Rajasthan Rajya Vidyut Utpadan Nigam Limited - Rajasthan

37860579 procurement of complete double acting pneumatic air cylinders for dome valve installed in fly ash handling system including rcc main silo , double acting pneumatic cylinder (complete cylinder assembly) with exhaust valve. size 160x250 mm model: vnc s20 160 x250 mm max pr: 10 bar make: neucon/airmax/schader/pioneer cylinder type double acting, bore dia. 160mm, stroke length 250mm, piston rod dia 40mm, piston rod thread m36x2p, pneumatics connection 3/4 bsp, barrel material aluminum hard anodized, piston rod/shaft material bs 970 90, en 8 hard chorme plated, seals hi nitrile, end cover aluminum alloy alsi 132, operating pressure 6.3 bar, testing pressure 10 bar, temperature 0 to 80?c, mounting accessories swivel flange & rod end fork with exhaust valve (drawing attached for reference) , seal kit for above pneumatic cylinder. seals hi nitrile, operating pressure 6.3 bar,testing pressure 10 bar, temperature 0 to 80°c , double acting pneumatic cylinder (complete cylinder assembly) with exhaust valve. size 100x250 mm, model: vncs20100x250 mm max pr: 10 bar make: neucon/airmax/schader/pioneer cylinder type double acting, bore dia. 100mm,stroke length 250mm, piston rod dia 25mm, piston rod thread m20x1.5p, pneumatics connection 1/2 bsp, barrel material aluminum hard anodized, piston rod/shaft material bs 970 90, en 8 hard chorme plated, seals hi nitrile, end cover aluminum alloy alsi 132, operating pressure 6.3 bar, testing pressure 10 bar, temperature 0 to 80?c, mounting accessories swivel flange & rod end fork with exhaust valve (drawing attached for reference) , seal kit for above pneumatic cylinder. seals hi nitrile, operating pressure 6.3 bar, testing pressure 10 bar, temperature 0 to 80°c...

North Western Railway - Rajasthan

37835863 supply of interchangeable, preset torque wrench with pre set value locking and safety device.having a spigot dia. of 16 mmmade of single piece of aluminium alloy body.torque range: 80 400 nm ( 60 300 lbf. ft. ) weight: 2.00 kgs. or less, length: 633mmsupply along with 1 / 2 inch sq. drive ratchet head for vande bharat train . make gedore / armstrong / ridgid / similar ....

Department Of Atomic Energy - Rajasthan

37710289 bids are invited for wrought aluminium and aluminium alloys bars, rods and sections (general engineering purposes) is:733 (q3) total quantity : 20...

Medical And Health Services - Rajasthan

37689695 supply of x ray and ecg items tender to buy x ray films, ecg jelly, ecg paper roll etc. at govt. dist. hospital, sri ganganagar , x ray film blue base blue sensitive high speed14”x17”fuji//nieue plus/vms / carestream/agfa/konika/ laser/e ray , x ray film blue base blue sensitive high speed 12”x15”fuji//nieue plus/vms / carestream/agfa/konika/ laser/e ray , x ray film blue base blue sensitive high speed 10”x12” fuji//nieue plus/vms / carestream/agfa/konika/ laser/e ray , x ray film blue base blue sensitive high speed 8”x10”fuji//nieue plus/vms / carestream/agfa/konika/ laser/e ray , dental x ray film high speedsize 2 [3cm*4cm fuji//nieue plus/vms / carestream/agfa/konika/ laser/e ray , x ray developer liquidfor automatic film processorto make 19 ltr. kodak/photon/carestream/fuji/champion , x ray fixer liquid for automatic film processorto make 19 ltr. kodak/photon/carestream/fuji/champion , digital x ray film dry view dve laser imaging film 8x10carestream [proprietary item] , digital x ray film dry view dve laser imaging film 10x12carestream [proprietary item] , fuji medical dry imaging films 8”x10” di hlfuji [proprietary item] , fuji medical dry imaging films10”x12” di hlfuji [proprietary item] , manual alluminium alloy xray cassette with intensifyscreen speed 800, blue sensitive14”x17” kiran/fujifilm/atico/ super photo chem , manual alluminium alloy xray cassette with intensifyscreen speed 800, blue sensitive 12”x15” kiran/fujifilm/atico/ super photo chem , manual alluminium alloy xray cassette with intensifyscreen speed 800, blue sensitive 10”x12” kiran/fujifilm/atico/ super photo chem , manual alluminium alloy xray cassette with intensifyscreen speed 800, blue sensitive 8”x10” kiran/fujifilm/atico/ super photo chem , direct view cr cassette with pq screen for dv classic cr14”x17” carestream [proprietary item] , direct view cr cassette with pq screen for dv classic cr 14”x14” carestream [proprietary item] , direct view cr cassette with pq screen for dv classic cr10”x12” carestream [proprietary item] , lead number (0 9) & (r&l) per set , dental x ray film holder , dental x ray film developer & fixer each 2.25 lts. , chest stand iron floor model , x ray view box (single film) , ecg jelly 250 ml /each , ecg paper roll (single channel) bpl / 50mmx20mtrs , ecg paper roll (three channel) bpl / 80mm x20mtrs , ecg paper roll (three channel) cardio fax 3r/other / 106mmx20mtrs , ecg paper roll (three channel) bpl / 108mmx20mtrs , ecg paper roll (6 channel) bpl / 120mmx15mtrs , ecg paper roll 210mm x 20ml/comon , usgroll / 110mmx20mtrs , usg jelly/ 250ml , ecg roll 8108 , ecg roll 8108 view (z fold) , ecg leads , ecg cups , b.p. instrument (digital) , b.p. instrument (led) , b.p. instrument (mercury) , b.p. bulb , b.p. cuff , b.p. bladder , b.p. regulator...

Department Of Local Bodies - Rajasthan

37370165 annual rate contract for electrical maintenance work with equipment for sub offices of municipal corporation bikaner. 1 wiring of light point / fan point / exhaust fan point / call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade ( is:694 ) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi marked mms ( is:9537 p iii ) vergin material pvc conduit & its all accessories ( j.b. , bends etc. ) , round tiles, 18 swg g.i. box with earth terminal, 6 a switch , 3 pin ceiling rose / lamp holder / 3 point connector, 3.0 mm thick isi marked phenolic laminated sheet ( is : 2036 1995 ) , al. alloy / cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 . for additional technical parameters of products / work , refer annexure a attached with this bsr . short point ( up to 3 mtr. ) 2 medium point ( up to 6 mtr. ) 3 long point ( up to 10 mtr. ) 4 wiring of 3 / 5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade ( is:694 ) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi marked mms ( is:9537 p iii ) vergin material pvc conduit & its all accessories ( j.b. , bends etc. ) , round tiles, 18 swg g.i. box with earth terminal of required size, 6 a switch, 3 / 5 pin 6 a socket, 3.0 mm thick isi marked phenolic laminated sheet ( is : 2036 1995 ) , al. alloy / cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07. for additional technical parameters of products / work , refer annexure a attached with this bsr . on board 5 short point ( up to 3 mtr. ) 6 medium point ( up to 6 mtr. ) 7 long point ( up to 10 mtr. ) 8 s&f following sizes ( dia. ) of isi marked mms ( is:9537 p iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories ( is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr .mms ( is:9537 p iii ) pvc conduit 25mm 9 mms ( is:9537 p iii ) pvc conduit 32mm 10 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm ) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a or c , flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc / ms conduit / casing capping including all as per pre approved by engineer in charge, making connections, etc. as required. oem must have its own in house nablab setup for all testing facilities for wires. for additional technical parameters of products / work , refer annexure a attached with this bsr .1 x 1.5 sq.mm 11 2 x 1.5 sq.mm 12 1 x 2.5 sq.mm 13 2 x 2.5 sq.mm 14 2 x 4.0 sq.mm 15 supply & drawing wiring for sub mains as per pwd specification for electrical works with isi marked ( is:694 ) , 1100 volts grade pvc insulated flat twin core sheathed solid aluminium conductor with 10 swg g.i. support wire duly clipped including all as per pre approved by engineer in charge, making connections, as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products / work , refer annexure a attached with this bsr . 4.0 sq.mm 16 6.0 sq.mm 17 10.0 sq.mm 18 supplying and laying isi marked p.v.c. insulated submersible cable as per pwd specification for electrical works confirming to is:694 and as per is 8130 : 2013 of 1.1 kv grade .wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm ) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a or c , flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4 including making connection etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. all as per pre approved by engineer in charge, making connections. for additional technical parameters of products / work , refer annexure a attached with this bsr . 2.5 sq.mm 3 core flat / round. 19 providing & fixing of 240 / 415 v ac mcb with positive isolation of breaking capacity not less than 10 ka ( b / c tripping characteristic as per type of load and site requirement ) 4kv impulse withstand voltage, as per pwd specification for electrical works with isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted with existing distribution board / sheets, min. operation 20, 000 upto 32 a rating and 10, 000 upto 63 a, 5000 for 80 a rating including making connections, testing etc. as required. . oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . single pole mcb 6 a to 32 a rating 20 double pole mcb6 a to 32 a rating 21 four pole mcb40 a rating 22 four pole mcb50 63 a rating 23 providing & fixing of ik09 recessed / surface mounting heavy duty horizontal type sheet steel not less then 1.2 mm thick distribution board as per pwd specification for electrical works isi marked conforming to is 13032 & is 8623 / conforming to iec 61439 3. phosphatised / powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar, masking sheet, including making internal db terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . ip 43 double door ( single phase ) . 8 way ( 8 o / g +2 i / c ) 24 ip 43 double door ( three phase ) 8 way ( 24 o / g + 8 i / c ) 25 providing & fixing of isi marked ( is :3854 ) 6 amp. flush type non modular switch as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, minimum width of switch toggle ( push part ) should not less then 16 mm, brass terminal & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 26 providing & fixing of isi marked ( is :3854 ) 16 amp. flush type non modular switch as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material , minimum width of switch toggle ( push part ) should not less then 16 mm, brass terminal & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 27 providing & fixing of of 3 pin 6 amp. flush type non modular socket as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 28 providing & fixing of 3 / 6 pin 16 amp flush type non modular socket as per pwd specification for electrical works, made out fromindustrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 29 providing & fixing of isi marked ( is :3854 ) 6 amp. combined flush type non modular socket and switch set as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, minimum width of switch toggle ( push part ) should not less then 18 mm, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 30 providing & fixing of isi marked ( is :3854 ) 16 amp. combined flush type non modular socket and switch set with indicator and fuse set as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 31 providing and fixing of non modular power plug point accessories as per pwd specification for electrical works with 18 swg g i box of size 175 x 100 x 60 mm with earthing terminal / connector on recessed / surface with suitable size phenolic laminated sheet ( is : 2036 1995 ) cover including cost of 16 amp. switch ( is :3854 ) and 3 / 6 pin 16 amp. socket outlet [ as per detailed in respective item in bsr ] , making connection , testing , etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 32 providing & fixing of isi marked ( is:1293 ) 6 amp unbreakable 3 pin plug top with lamp indicator as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, brass terminal including making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 33 providing & fixing of isi marked ( is:1293 ) 16 amp unbreakable 3 pin plug top with lamp indicator as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, brass terminal including making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 34 providing & fixing of non modular socket size flush type 120 watt rotary minimum 5 step fan regulator as per pwd specification for electrical works, isi marked ( is:11037 ) made out from industrial grade polycarbonate or fire resistant abs material including making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 35 providing & fixing of isi marked ( is:2268 1994 ) single / multi tone electronic call bell as per pwd specification for electrical works, including making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 36 supply, fixing and testing of following capacity wall mounted stablisers having output voltage variation from 200v to 250v ( + / 5% ) with input voltage variation from 170v to 260v, time delay facility from 2 to 4 minute and high cutoff at 270v complete in all respect e074601 3 kva 37 providing & fixing of ip51 direct or ct operated, 1x240 / 3x240 volts, 50 hz static watt hour meter ( kwh ) as per pwd specification for electrical works, isi marked ( is :13010 2002 ) having resolution 0.1 / 0.01 kwh , accuracy class 1 as per is:13779, led indicators for tamper operation ( reverse & / or earth connection ) , pulsating led indicator for meterology , lcd display, cover plate for body and terminal sealing , push button for all standard parameters, including making connection , testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 10 a to 60 ampere single phase meter. 38 providing & fixing of iso certified company made tp&n 415 v side handle operated double break fuse switch unit in sheet steel enclosure as per pwd specification for electrical works conforming to is / lec 60947 3 : 1999 ( w / o hbc fuses ) including making connections with suitable lugs, testing etc. as required. appropriate type test certificate / oem test report shall be submitted . all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 100 a rating 39 providing & fixing of iso certified company made 240 / 415 v porcelain kitkat fuse ( / hbc type ) as per pwd specification for electrical works conforming to is:2086, 1983 on existing board / sheet including making connections with lugs, testing etc. as required . appropriate type test certificate / oem test report shall be submitted . all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 63 a , 415 v. 40 100 a , 415 v 41 providing & fixing of iso certified company made bus bar chamber housed in sheet metal box as per pwd specification for electrical works confirming to iec 60439 / is 8623 & iec 60529 / is 2147 made out from 1.6 mm thick powder coated crca sheet, degree of protection ip 31 front openable bus bar made out of aluminium or wrought aluminium alloy suitable for 200 amp. capacity , bus bar fixed on porcelain / dmc insulators at approved spacing including making connections etc. as required. appropriate type test certificate / oem test report shall be submitted . all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 300 mm long , 4 strip. 42 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed unarmoured / armoured aluminium cable of 1.1 kv grade as per pwd specification for electrical works in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points ( a ) , ( b ) , ( c ) , mentioned below: ( a ) material : h4 grade aluminium conductor of purity >99.6 % & as per is:1554 p i / is :7098 p – i ( b ) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999 for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 ( part 0 to 64 ) for testing procedures. ( c ) oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities for cables . appropriate type testcertificate / oem test report shall be submitted . all above as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr. e110110 un armoured 16.0 sq. mm 4 core. 43 un armoured25.0 sq. mm 4 core 44 providing & laying of double wall corrugated pipe confirming to is : 14930 p 1 & 2 with hdpe coupler at 1 mtr. depth below the ground for laying cable including making the trench and back filling , compaction of earth as required ( excavation of earth to be paid extra as required. ) of following outer dia. / inner dia as per is:4984:1995. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr .55 / 50 mm. 45 sitc of chemical gel earthing system of dual pipe technology made of with b class g i pipe as per is 1239 ( part 1 ) :2004 of medium duty of following sizes as per points mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : ( a ) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, cpri / erda tested with rms capacity of minimum 35 40 ka for withstanding 1 second . ( b ) to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated lab for low resistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major content as per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts ( c ) heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height 250 to 300 mm. ( d ) testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. ( e ) self certificate for confirming above standards from oem is mandatory. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . e140510 with pipe in pipe technology ( outer pipe dia. / inner pipe dia. ) minimum 100 mm dia borewell gi pipe 2000 mm long, 50 / 25mm, terminal 40mm x 6 mm gi strip. 46 supply & laying following size earth strip in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, jointing shall be done by overlapping and with 2 set of brass ( for custrip ) / gi ( for gi strip ) nut bolt & spring washer spaced at 50cm making connection etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 25mm x 3mm g.i. ( hot dipped ) strip 47 supply & laying following size earth wire in horizontal or verticalrun in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu thimble etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 8 swg copper wire. 48 providing & fixing of iso certified company made bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan as per pwd specification for electrical works, conform to all the performance requirements laid down in is:374 2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) or quality certification such as iso 9001 or above. with down rod up to 30 cm with secondary support. 1200 mm sweep bee 2 star rated ( service value >=4.5 to < 5 ) . 49 providing & fixing of of double ball bearing, copper wounded capacitor start single phase metallic blade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. oem shall be an iso certified company. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 225 mm sweep 50 providing & fixing of heavy duty capacitor start, copper wound double ball bearing 900 / 1400 rpm single phase exhaust fan as per pwd specification for electrical works, conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. oem shall be an iso certified company. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 300 mm sweep ( 900 / 1400 rpm ) . 51 providing & fixing of capacitor start, copper wound, metal body, metal blade three speed wall mounting fan of following sweep with the help of anchor bolts including making connection testing etc. as required. oem shall be an iso certified company. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 400 mm sweep ( oscillating type ) . 52 providing & fixing of fluorscent tube rod in existing fixtures as required complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . flourscent powder coated. 36 / 40 watts. 53 providing & fixing of energy efficient / energy saving ip 20 led direct retrofit bulb in existing holder or fixture as required with system lumen efficacy =100 lm / watt output , pf 0.95 , cri >70, minimum life time of minimum 25000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 / lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product / work, refer annexure a attacheded with this bsr. 9 watt 54 15 watt 55 rewinding of ceiling fan motor ( starting and running winding ) including all necessary material. the motor is to be wound taking no. of coils, turns and pitch as it was originally wound with required size super enamelled wire with e class insulation material and making connections etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. ( new model ceiling fan ) . 900 / 1200 mm sweep ( new model ceiling fan ) 56 labour charges for removing and refixing of ceiling fan / exaust fan from site 57 charges for oiling, overhauling of ceiling fan, table fan, pedestal fan irrespect to the size of fan including removing, refixing of fan from site and testing etc. as required. fans with removing & refixing at suitable location. 58 providing and replacement of ball bearing of ceiling / exhaust fan and refixing the same at suitable location as requiredand as per oem recommendations. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 59 p & replacement of cover / bearing seat of ceiling / exhaust fan. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 60 p & f aluminium blades ( a set of 3 blades ) duly painted and well finished 900 / 1200 mm. the material of the fan blade shall be of designation 31500b with condition hx6 aluminium alloy sheet confirming to is 737 / 2008. 61 servicing and overhauling of 20 sweep desert cooler including oiling, greasing, painting of tank from inside with rubber paint after properly desmantling each assembly and refixing the same as required. 62 painting of desert cooler with two coats of rubber paint inside of water tank and two coat of synthetic enamelled paint on both side of cooler body, fan body, grills etc.after cleaning with sand paper, complete in all respect as required. 63 replacement of cooler pads ( heavy ) set of 3 no. of size 25 x 27 64 p & f aluminiun blade for 20 desert cooler fan as required. 65 p & f of isi marked vertical pump suitable for 20 desert cooler including making connection testing etc. as required. isi marked vertical pump. 66 p & f fan motor suitable for 20 desert cooler including making connection testing etc. as required. with copper winding motor isi marked. 67 rewinding of heavy duty exhaust fan motor including all necessary material, the motor is to be wound taking no. of coils, turns and pitch as it was originally wound with required size supernamelled wire with e class insulation material and making connections etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 300 / 380 mm sweep. 68 rewinding of motor of desert cooler pump with super enamelled copper wire, e class insulation material including removing, refixing, testing etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 69 rewinding of motor of desert cooler fan with super enamelled copper wire, e class insulation material including removing, refixing, testing etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by thecontractor. 70 supplying and charging of fresh refrigerant and testing of performance of air conditioner / fridge / water cooler of following capacity including capillary and strainer / filter. 1.5 tr window / split a.c. 71 2.0 tr window / split a.c. 72 25 / 50 / 40 / 80 ltr. water cooler 73 replacement of defective compressor by company repaired compressor as per oem recommendations of following gadgets including testing etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 1.5 tr a.c. 74 2.0 tr a.c. 75 25 / 50 / 40 / 80 ltr. water cooler 76 p & replacement of condensing / cooling coil of copper fins for following capacity a.c. / water cooler / fridge as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 1.5 tr a.c. 77 2.0 tr a.c. 78 25 / 50 / 40 / 80 ltr. water cooler 79 servicing of 1.0 / 1.5 / 2.0 tr capacity split / window type air conditioner. 80 p & replacement of overload protection of a.c. / water cooler as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 81 p & replacement of thermostat of a.c. / water cooler / fridge as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 82 p & replacement of selector switch of 1.0 / 1.5 / 2.0 tr a.c fan as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 83 p & replacement of starting relay of a.c / water cooler / fridge compressor as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 84 s & f of capacitor of 230v / 275v, 50hz rating of plastic casing and terminals lugs or copper wire. starting capacitor.40 60 micro farad. 85 60 80 micro farad. 86 running capacitor 2.5 / 3.15 micro farad. 87 4.0 micro farad 88 6.0 micro farad 89 8.0 micro farad 90 10.0 micro farad 91 providing & fixing of ip20 led surface / recessed / suspended mounting mid power smd type led light fixture made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 2.5 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection and in compliance to iec standards ( integral with light fixture ) . system lumen efficacy min. 100 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl acredeated lab setup for all testing facilities for led fixtures. ( lm79 / lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . for additional technical parameters of product / work, refer annexure a attacheded with this bsr. recessed mounting 48w led light fixture 2x2 with acrylic / prismatic front cover. 92 gas charging of vrf / vrv system with r410a refrigerant gas. before gas charging system shall be flushed with high purity nitrogen gas to remove carbon content, dirt particles to make sure that there is no chance of mixing any impurity with refrigerant gas. thereafter system shall be tested with nitrogen gas at 1.5 times of working pressure of r410 refrigerant gas to ensure leakproof system. whole system shall be vacuumed up to 500 micron level which ensures the zero moisture content level in piping to ensure better cooling efficiency and long life of the system. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr ....

Military Engineer Services - Rajasthan

37255521 welcome maintenance for offrs qtrs under age b / r ii under ge ( n ) bikaner. 1 m&l preparingof old decorated surfaces of walland applying one coat of distemper oil emuision complete all as specified and as directed by engr in charge. 2 m&l preparingof old decorated surfaces of walland applying two coat of distemper oil emuision complete all as specified and as directed by engr in charge. 3 m&l preparing surfaces of plaster or unplaster old surface of wall and applying one coat of white wash complete all as specified and as directed by engr in charge. 4 m&l preparing surfaces of plaster or unplaster old surface of wall and applying two coat of white wash complete all as specified and as directed by engr in charge. 5 m&l preparing surfaces of plaster or unplaster old surface of wall and applying one coat of white wash on ceiling complete all as specified and as directed by engr in charge. 6 m&l preparing surfaces of plaster or unplaster old surface of wall and applying two coat of white wash on ceiling complete all as specified and as directed by engr in charge. 7 m&l preparing old surfaces of wall and applying one coats of plastic emulsion paint complete all as specified and as directed by engr in charge. 8 m&l preparingold surfaces of ceiingand applying one coats of plastic emulsion paint complete all as specified and as directed by engr in charge. 9 m&l preparing old surface of wood of any desc over 10cm width or girth and applying two coats of synthetic enamel paint .over pink primer complete all as specified and as directed by engr in charge. 10 m&l preparing new surface of steel of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide complete all as specified and as directed by engr in charge. 11 m&l preparing the old painted wooden surfaces of any description over 10 cm width or girthand applying one coat of synthetic enamel paint.complete all as specified and as directed by engr in charge. 12 m&l preparing new surface of steel of any desc over 10cm width or girth and applying one coat of synthetic enamel paint over red oxide complete all as specified and as directed by engr in charge. 13 m&l complete removal of existing treatment and applying a thin layer of putty on wall surfaces complete all as specified and as directed by engr in charge. 14 m&l preparing new surface of old or new incl removal of old treatment ans applying a thin layerof plaster of paries to give a uniform finish as approved by engr in charge 15 m&l demolition of cement conc. in any description and incl any position not otherwise specially provided complete all as specified and directed 16 m&l dismanting floor, hearth or wall tiling including cement mortar bedding and removal of rubbish out of the premises complete all as specified and as directed by engr in charge. 17 hacking out old broken glass ( any thickness, size, quality or description ) fromwooden frame or stone concrete or brick surrounds glazed with putty or fixed with beads.complete all as specified and as directed by engr in charge. 18 dismantlingpipes of any desc fixed to wall or laid under floor complete all as specified and as directed by engr in charge. 19 dismantling cast iron pipes of any desc fixed to wall or laid under floor complete all as specified and as directed by engr in charge. 20 taking down cement plaster on brick or stone walls, including raking out joints, hacking for key, scrubbing down with water etc. 21 taking up or down steel tubing 15 mm diaand connections and stacking neatly for offering credit complete all as specified and as directed by engr in charge. 22 all as per item n 21 above, but 20 mm dia. complete all as specified and as directed by engr in charge. 23 taking down chowkhats or frameswith shutters ( without taking off shutters from the frames ) of size n. exc 1.5 sqm each complete all as specified and as directed by engineer in charge. 24 taking down chowkhats or frameswith shutters ( without taking off shutters from the frames ) of size exc 1.5 sqm but not exc 4.0 sqm each complete all as specified and as directed by engineer in charge. 25 taking down shutters of any description, areaexceeding 1.00 sqm and n.exc 2.00 sqm eachcomplete all as specified and as directed by engineer in charge. 26 m&l for welding in repairs n.exc 2.5 cm in length and not exceeding 6mm thick of metal complete all as specified and directed by engineer in charge. 27 s&f 1.25 mm thick pressed steel frames of size 125mm x 60mm for single doorsincluding necessary fixing lugs, hinges, lock strike plate, etc complete all as per is provns.complete all as specified and as directed by engr in charge. 28 s&f 1.25 mm thick pressed steel frames of size 105mm x 60mm for single doorsincluding necessary fixing lugs, hinges, lock strike plate, etc complete all as per is provns.complete all as specified and as directed by engr in charge. 29 s&f second classhard wood plain, framed, panelled shutters 35mm thick, ( any number of panels ) with panels of timber flat on both sides ( feather edged ) or of veneered partcile board medium density wood particle board with commercial faces venners supplied and fixed to chowkats.complete all as specified and as directed by engr in charge. 30 s&f second class hard wood, glazed and skelleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etcwithout sash bar, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing gauze etc, size of members as directedsupplied and fitted to chowkats complete all as specified and as directed by engr in charge. 31 m&l for 25 mm thick flush shutters for cupboards solid core construction, with block board core, and ply wood face panels, both faces covered with decorative face veneer with lipping to matchcomplete all as specified and as directed by engineer in charge. 32 s&f solid pvc door frame of size 50 mm x 47 mm made out of 5 mm plain colour pvc sheet reinforced with m.s. square tube suppling & fixing in opening all as specified and as directd. 33 s&f factory made solidpanel pvc door shutter 30mm thick ( style ) consisting of framemade out of ms tubes for top and bttom rails. ms frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colourpvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail, panneling of plain color pvc sheetto be fitted in the ms frame welded / sealed to the stiles &rails with suitable pvc sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site all as specfied and as directed. 34 s&f steel window / ventilators pressed steelframed ( box type ) factory made glaged and guaged with side hung shutters including pintolhinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded incl a prov of cooler / ac opening with shutter including one shop coat of red oxide primer complete all specified.note :i ) he window shall be fabricated as per drg no cebz / 888r & 889 sheet 1 to 4. ii ) ms fillets, glazing, wire gauge shall be measured and paid separately. 35 s&f framed work such as grills , framed guard bars barred iron doors ;ladders framed balusters railings and similar work conforming to fe 410 0or fe 310 0 complete all as specified and as directed by engr in charge. 36 s&f stainless steel wire cloth o.36mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples.complete all as specified and as directed by engr in charge. 37 s&f stainless steel wire cloth o.36mm nominal dia of wire and average width of aperature 1.40mm and fixed in repairwith stainless steel wire staples.complete all as specified and as directed by engr in charge. 38 m&l for second classhard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the soild, rounded or chamfered, put together with glue pinned at joints.complete all as specified and as directed by engr in charge. 39 m&l second classhard wood, in scantling wrought, in timber fixed complete all as specified and as directed by engr in charge. 40 teakwood beading 20x60mm half round complete supplied and fixed complete all as specified and as directed by engr in charge. 41 s&f 18 / 19 mmplywood, grade 1 ( with bwr resistant / termite proof ) with fixed with screws to timber frame work as in cup boards / cabinets etc complete all as specified and as directed by engr in charge. ( make : century / kitply / or other app by ge ) 42 m&l for water proofing block boards 18 / 19 mm , grade 2 exterior quality grade , commercial type fixed with screws to timber frame work. complete all as specified and as directed by engr in charge. 43 m&l for 0.9 mm thick decorative choice of laminates type i of surface finishwhitestuck with importedadhesive on sides of board as directed by eng in charge . ( make corby, or euro ) 44 m&l prelaminated partical board 19 / 20mm medium density , prelaminated with one side with decorative choicelaqmination and other side balancingwith white laminationfixed with screws as in shelves to kitchen almirah and cub board fixed in repair.complete all as specified and as directed by engr in charge. 45 s&f 12mm thick plywwod grade bwr , type bb , fixed with screws to timber frame work.complete all as specified and as directed by engr in charge. 46 s&f 6mm thick plywwod grade bwr , type bb , fixed with screws to timber frame work.complete all as specified and as directed by engr in charge. 47 m&l for 0.9 mm thick decorative choice of laminationtype 1 of surface finish , colour and pattern as approved adhesive as per manufacturers instructions complete all as specified and as directed by engr in charge. 48 m&l for 1.50 mm thick pvc laminated decorative impressionchoice of laminationtype 1 of surface finish , colour and pattern as approved adhesive as per manufacturers instructions ( corby / duco ) . 49 s&f stain less steel catcherof superior quality complete all as specified and as directed by engr in charge. 50 s&f stain less steel pivoted type hingesof superior quality complete all as specified and as directed by engr in charge. 51 s&f 75mm long brass handle of desired finish with screws as approved by engg in charge. 52 s&f 35mm long mortice lockcomplete all as specified and as directed by engr in charge. ( make :godrej / harrison ) 53 s&f 75mm long brass tower bolt of desired finish with screws as approved by engg in charge. 54 s&f drawer side channel of std size and incl of rooler for moving drawer, mild steel bright finish, or electrogalavanised width of flap 30mm & length 60 mm all as specified. 55 s&f stainless steel fancy type, bright finish handles fixed with screw, of 125mm size all as specified. 56 s&f stainless steel multipurpose bracket in wooden / partitions for storing rations types made of 4mm dia stainless steel rods, fixed in side partition etccomplete.make: usha shriram enpt or equivalent ) . 57 s&f stainless steel luddel craddle hanging stand for cutlery all as specified and directed dy engr in charge.make: usha shriram enpt pvt ltd. 58 s&f stainless steelzero crank hinges fancy type ( with euro concealed hinges make: avis gold or equivalent ) fixed to shutter in cub board of std size and shape all asdirected dy engr in charge. 59 s&f 7s&f sinks made of stainless steel lmmthickkitchenorlaboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including fixing contilever brackets and connecting union to pipe complete all as specified and as directed by engr in charge. 60 m&l for recessed type stain less steelhandle for cup boards size 150 mm long complete all as specified and as directed by engr in charge. 61 m&l for roller ( pvc / stain less steel ) suiltable for sliding shutters . as app by eng in charge 62 pvc toilet cabinet with shelves and shutters fixed with looking mirror of size 600 x 450 mm complete all as specified and as directed by engr in charge. ( make : commander or equivalent ) 63 s&f continous ( piano ) hinges 30mm wide mild steel bright hinges 30 mm with flap, ms bright finished or electrogalvanised complete all as specified and as directed by engr in charge. 64 hasp and staple 100mm aluminium anodised, safety type, with mild steel hinges pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by engr in charge. 65 s&f mild steel peg set stay 300 mm with and incl screws and bolts complete all as specified and as directed by engr in charge. 66 butt hings, 100 mm long, extructed aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type c 21.complete all as specified and as directed by engr in charge. 67 s&f butt hings, 100 mm long, extructedisi marked complete all as specified and directed by engr in chargefixed complete all as specified and as directed by engr in charge. 68 s&f extruded aluminium alloy handles, 100 mm long, fabricated type anodised complete all as specified and as directed by engr in charge. 69 s&f aluminium, anodised , 100 mm long, barrel tower bolts of extruded section and fixed complete all as specified and as directed by engr in charge. 70 s&f extruded aluminium alloy handles, 150 mm long, fabricated type anodised complete all as specified and as directed by engr in charge. 71 s&f aluminium, anodised , 150 mm long, barrel tower bolts of extruded section and fixed complete all as specified and as directed by engr in charge. 72 supply and fix floor door stopper of aluminium alloy body, overall length of cover plate 140 mm and tongue anodised with hard drawn steel sring fixed in floor complete all as specified and as directed by engr in charge. 73 s&f aluminium alloy, anodised, slidding door bolt300mm long, with hasp staple ( bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and as directed by engr in charge. 74 s&f mild steel, 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete fixed in repair complete all as specified and as directed by engr in charge. 75 s&f figured glass, pin head type, 4mm thick and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and as directed by engr in charge. 76 s&f 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not execeeding 0.5 sqm in each pane for metal frames complete all as specified. 77 s&f anodised aluminium with powder coating frame for doors, windows , ventilators with one or more rebates includirg joining cleat for fixing etc. complete all as specified and as directed. 78 s&f anodised aluminium frame for doors, windows , ventilators with one or more rebates includirg joining cleat for fixing etc. complete all as specified and as directed. 79 s&f sheet glass, ordinary quality 5.5 mm thick for aluminium door , window and vent.and glazing in square n exc 0.5 sq.m in each pane complete all as specified. 80 s&f neoprene / epdm rubber gasket for fixing sheet glass complete all as specified. 81 m & l pcc25 mm thick 1:2:4 type b0 ( 12.50 mm graded aggregate ) in any position in ground floor / roof complete all as specified and as directed by engr in charge. 82 m & l pcc75 mm thick 1:3:6 type b0 ( 12.50 mm graded aggregate ) in any position in ground floor / roof finishing cement concrete surface without using extra cement complete all as specified and as directed by engr in charge. 83 m & l pcc1:2:4 type b1 ( 20 mm graded aggregate ) as in hold fast blocks rungs etc icluding necessary form work complete all as per specified and directed ny engr in charge 84 m & l pcc 1:3:6 type c0 ( 12.50 mm graded aggregate ) as in filling in pressed steel frames complete all as specified and as directed by engr in charge. 85 m and l for coloured non skid ceramic tiles exceeding 0.11 sqm but not exceeding 0.18 sqm 7 to 8mm thick in floorsset and jointed in neat cement slurry and pointed incoloured cement to match the floorlaid over 15mm thick screed in cement mortar 1:6.complete all as specified and as directed by engr in charge. 86 m&l glazed ceremic tiles white450x300mmx7mm thickcoloured, set and jointed in neat cement slurry and pointed in white cement or coloured to match colour matching with floortiles as on vertical surfaces laid over 10mm thick cement screed in 1:4.complete all as specified and as directed by engr in charge. 87 m&l chequered cement concrete tiles 25 cm x 25 cmx25mm thick with grey cement and no pigment set jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed in cement and sand mortar 1:4 complete all as specified 88 m&l for vitrified tiles not exceeding 0.36 sqm 10 mm thick in floors set and jointed in neat cement slurry and pointed in neat cement s;urry in floors including 15 mm thick screed bed in cement and sand mortar 1:4 complete all as specified 89 m&l for vitrified tiles not exceeding 0.36 sqm 10 mm thick in floors set and jointed in neat cement slurry and pointed in neat cement s;urry in floors including 15 mm thick screed bed in cement and sand mortar 1:4 complete all as specified but in vertical surface. 90 m and l for 20mm thick granitemachine cutslab table rubbed and polished graniteas on cooking platforms incl. pointing in white cement 1:2using marble dustwith admixture of pigmentto match with marble shadelaid over 20mm thick cement screed in cement mortar 1:6.complete all as specified and as directed by engr in charge. 91 rendering 10 mm thick in cm 1:6 on other than fair faces of brick work or concrete surfacesfinished fair and even complete all as specified and as directed by engr in charge. 92 rendering 15 mm thick in cm 1:4 on fair faces of brick work or concrete surfacesfinished fair and even complete all as specified and as directed by engr in charge. 93 rendering 5mm thick on fair faces ofconc. surfaces in cement mortar 1:3, even and smooth w / o using extra cement as on ceiling.complete all as specified and as directed by engr in charge. 94 s&f tubes, medium grade galvanised, 15 mm borewith all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed by engr in charge. 95 s&f tubes, medium grade galvanised, 20 mm borewith all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed by engr in charge. 96 s&f aluminium sheeting 0.56 mm thick alloy 31000 h4 in ridges, hips, valley gutter drip and straight flashing ( length and girth as fixed ) complete all as specified and as directed by engr in charge. 97 s&f mild steel work as in hold fasts, clamps, bands, straps etc conforming to fe 410 0 complete all as specified and as directed by engr in charge. 98 s&f sinks with drainage board made of stainless steel 1mm thick kitchen or laboutery with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460mm bowl size 410 mm 330 mm x 160mm complete all as specified and as directed by engr in charge. 99 s&f stainless steel plate rack, tubular type, with fixing arrangement900mm x 900 mm size all as directed and as approved by engr in charge. 100 s & f glass corner of size 300mmx300mm with5.5 mm thick glass andsteelness steel clip and steelness steel railing allround the shelfcomplete all as specified and directed by engineer in charge . 101 s&f 600x450mm bevelled edge mirror of selected quality glass mounted on 6mm th ac building board or commercial ply complete all as specified and as directed by engr in charge. 102 s&f 5mm thick looking mirror of selected quality with and including stainless steel spacers any size as approved by engrbevelled edge mirror of selected quality glass mounted on 6mm th ac building board or commercial ply complete all as specified and as directed by engr in charge. 103 s&f pvc ( swr ) pipes 75 mm bore, single socketed, in any length with rubber ring jointed fixed to walls complete all as specified and as directed by engr in charge. 104 s&f pvc ( swr ) pipes 110mm bore, single socketed, in any length with rubber ring jointed fixed to walls.complete all as specified and as directed by engr in charge. 105 s&f pvc ( swr ) branch piece, single ( single y ) equal or unequal, 75mmbore.complete all as specified and as directed by engr in charge. 106 s&f pvc ( swr ) vent cowl 75 mm complete all as specified and as directed by engr in charge. 107 s&f pvc ( swr ) floor trap 75 mm, plain with grating including jointing with solvent cement complete all as specified and as directed by engr in charge. 108 s&f pvc ( swr ) branch piece, single ( single y ) equal or unequal 110mmbore.complete all as specified and as directed by engr in charge. 109 s&f pvc ( swr ) bends any radius 75mm bore complete all as specified and as directed by engr in charge. 110 s&f pvc ( swr ) bends any radius 110mm bore complete all as specified and as directed by engr in charge. 111 s&f pvc ( swr ) gully trap 125 / 110 mm setting and jointing with solvent cement complete all as specified and as directed by engr in charge. 112 s&f in repair stack clamp out of 40mm x3mm flat iron stays with rubber gasket covering including bolt and nuts, spacer and securing ends of stays to walls or roof for 50mm bore piece complete all as specified and as directed by engr in charge. 113 s&f in repair stack clamp out of 40mm x3mm flat iron stays with rubber gasket covering including bolt and nuts, spacer and securing ends of stays to walls or roof for 100mm bore piece complete all as specified and as directed by engr in charge. 114 disconnecting existing tanks, setting aside ( or lowering if required ) for repairs cleaning etc andhoisting if required reconnecting and refixing in position after cleaning and removing all scale and dirtetc from tanks and from mouths of circulating pipes etc complete ( capacity of tanksexc 250 ltr and n exc 500 ltrs ) complete all as specified and as directed by engr in charge. 115 s&f rotational moulded double layer ( isi marked of app make ) polythene water storage tank ( cylindrical vertical with closed top ) hoisted and fixed in position of 500 ltrs including dismantling existing.complete all as specified and as directed by engr in charge. 116 s&f ball valve high pressure of ptmt with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixedfixed in repair.of 20mm complete all as specified and as directed by engr in charge.make : prayag or equivalent. 117 s&f brass cp wall mixer non telephonic for mixing hot and cold water screwed down for iron pipe 15mm bore.complete all as specified and as directed by engr in charge. ( make : parryware or hindware or equivalent ) . 118 s&f brass cp whb mixer non telephonic for mixing hot and cold water screwed down for iron pipe 15mm bore complete all as specifie and as directed by engr in charge . ( make : parryware or hindware or equivalent ) . 119 s&f vitreous china wash down water closet pan with fixing bolts, trap ( pedestal pattern ) , white, ( excludingflushing cistern and flush pipe ) complete fixed in repairs complete all as specified and as directed by engr in charge. 120 supply and fix vitreous chinawash hand basin flat back size 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand etc complete fixed in repairs complete all as specified and as directed by engr in charge. 121 s & f pvc valveless ( syphon internal fitting ) of pvc low levelaction type flushing cistern, 10 ltr capacity low level , whitewith inlet, ball valve, float and handle including brackets fixed in repairs complete all as specified and as directed by engr in charge. 122 s & f pvc valveless syphonic action type flushing cistern, 10 ltr capacity low level , whitewith inlet, ball valve, float and handle including brackets fixed in repairs.complete all as specified and as directed by engr in charge. 123 s&f pvc connections 15 mm size with ptmt nuts of length 450 mm complete all as specified and as directed by engr in charge. 124 s&f stainless steel tubular towel rail, 200 mm dia d type 60cm long between flanges complete all as specified and as directed by engr in charge. 125 s&f bib tap 15 mm dia, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwedfor iron pipeand fixed in repairs complete all as specified and as directed by engr in charge. ( make : parryware or hindware or equivalent ) 126 s&f bib tap 15 mm dia, long body fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwedfor iron pipeand fixed in repairs complete all as specified and as directed by engr in charge. ( make : parryware or hindware or equivalent ) 127 s&f stop valve, 15 mm dia, fancy type, chromium plated, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repairs complete all as specified and as directed by engr in charge. 128 s&f stop valve, 15 mm dia, concealed stop valvefancy type, chromium plated, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repairs complete all as specified and as directed by engr in charge. 129 s&f pillar taps, 15mm dia, fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, long screwed shanks and fly nuts, screwed for iron pipe and fixed in repairs.complete all as specified and as directed by engr in charge.make: jaquar or equivalent 130 s&f brass chromium plated shower rose 125 mm size including fixing to steel pipe or union fixed in repairs complete all as specified and as directed by engr in charge.make: jaquar or equivalent 131 sf brass chromium plated shower arm 15 mm 195 mm long with bend 45 degreemm size including fixing to steel pipe or union fixed in repairs complete all as specified and as directed by engr in charge.make: jaquar or equivalent 132 s&f sheet glass shelf assembly in repair , oconsisting of 5.5 mm thick sheet glass shelf 12 cm wide chromium plated bracket guard and railing 60 cm long complete all as specified. 133 s&f plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by engr in charge. 134 s&f cp health faucetfixed type suitable for ewcs with 1, 5 mtr stainless steel tube complete all as specified and directed by engineer in charge make : jaquar, prayag 135 s&f cp toilet paper holder fancy type complete all as specified and directed by engineer in charge.make: jaquar or equivalent 136 s&f angle valve cast copper alloy fancy type cp with long shank and cup and screwed for iron pipefixed in repair complete all as specified and as directed by engr in charge.make: jaquar or equivalent 137 s&f waste pipe 32mm for whb with coupling fixed in repairs complete all as specified and as directed by engr in charge. 138 m&l for along the wall below concrete or masonry using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed by engr in charge. 139 m&l for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 ( 1 cement: 2 coarse sand ) to match the existing floors complete all as specified and as directed by engr in charge. 140 s&f grating doom 125 mm dia with waste hole of ptmt ( minimum weight 40 gms ) complete all as specified and as directed by engr in charge. 141 s&f chromium plated soap dish complete all as specified and directed by engineer in charge. 142 s&f aluminium snake bead with bush duly fitted with screws with length equal to door width as specified and directed by engr in charge 143 m&l for repairingof rolling shutters making functional by providing greasing oiling , welding etc.including taking down rolling shutters or hood if required complete all as specified and as directed. 144 s&f safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed by engr in charge. 145 s&f ball bearing for rolling shutters.complete all as specified and as directed by engr in charge. 146 m&l for 25mm to 30mm thick plaster of paris ( pop ) ( gypsum anyhydrous ) raised moulding to flat surface of ceiling including preparation of surfaces all as directed.complete all as specified and as directed by engr in charge. 147 m&l for green sheet pvc of best quality to cover the surface where required complete all as specified and as directed. 148 s&f water closet pedestral pattern white or coloured ( as approved by engr in charge ) make :cera cat no.s1013113 ( cristy single piece suite p or s trap incl seat cover ) or equivalent in hindware , jaquar, parryware ) complete all as specified and as directed. 149 s&f in aluminium composite panel of any colour of having thickness of approx 3 4mm thick which are used in aluminium doors / partitions of all as specified and as directed. 150 s&f in pre laminated pvc boards of heat and fire resistant , non toxic , anti chemicaland corrosion resistant, termite proof and resistant to fungal attacks used in kitdhen cabinets of any finish complete all as specified and as directed. 151 m&l washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 ( 1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per square metre, top layer 15mm cement plaster 1:1 / 2:2 ( 1 cement: 1 / 2 coarse sand : 2 stone chipping 10mm nominal size ) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified ( paymentfor providing grooves shall be made separately ) . 152 s&f 10.00 mm thick gypsum boards as in ceiling as per approved desidg including recessing for provision of ceiling lights , moisture resistant , incl intermediate , perimeter channel ceiling channel , alon nuts and bolts connecting plates gypsum boards , dry wall screws soffits cleats , ceiling section, rowel plugs fixtures and screws complete all as spfd and as shown in sketch and applying twwo coats of emulsion paint over a coat primer on exposed surfaces.design of ceiling board as app by engr in charge. ( note: no extra payment shall be claimed from contractor for designs to ceiling falls etc ad shall be measured in plan only ) 153 m&l for 1.5mm thick self adhesive waterproofing membrane consisting of self adhesive sbs ( styrene butadiene styrene ) modified / bitumen compound covered on the top side with high density cross laminated polyethylene film and on the underside with an easy to peel silicon film all as per manufacturer’s instructions having minimum overlaps 50mm on sides and 100mm on ends, provided with & including suitable bitumen primer @ 0.30 litre per sqm as recommended by membrane manufacturer after cleaning the roof surface / sunken floor from all loose, dust, dirt, foreign material and particularly oil and grease marks, complete all as specified and as directed.make : m / s texsa india ltd / m / s pidilite industries ltd / m / s sika india pvt ltd / m / s stp limitednote : the net area of waterproofing treatment shall be measured and paid for without any extra allowance for side & end laps for membrane and this aspect shall be deemed included in the quoted rates. 154 taking down carefully ( aluminium ) point wiring complete of any type ( batten / surface conduit or concealed ) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper / white washing / colour washing to match with the existing surface complete all as spcified and directed. 155 taking down submain wiring aluminium / copper of any size including earth continuity condutor on teak wood or conduit and removing from site and making good the disturbed surface of wall etc complete all as specified and directed. 156 taking down old u / s existingdb tpn 4 way anddb spn 12 way including mcb / mccb of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed. 157 m & l for point wiring with and including single core frlsh pvc insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm 1100 volts grade drawn through and including suitable size of pvc concealed conduit with accessorieswithlaminated top cover fixed on ms sunken box for housing of switch, socket, regulator etc complete with and including 1.5 sqmmfrlsh pvc insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete all as specified and as directed by engr in charge for the following : ( a ) one light / fan / ex fan / bell / point controlled by one switch. 158 ( b ) one pin 5 amps socket point on the same board with other switches complete 159 ( c ) one 3 pin 5 amps socket on independent board. 160 ( d ) all as per item no 4 above but but one light point controlled by two 02 way switchboard complete and all as directed by engr in charge. 161 ditto all as per item no 157 above but with 4.0 sqmm copper wire for 3 pin socket outlet 20 amp on independent board complete and all as directed by engr in charge. 162 s&f switch piano type, 5 amp, single pole one way, 230 volts, flush type complete all as specified and as directed by engr in charge. 163 s&f switch piano flush type single pole, one way 15 / 20 amps 230 voltscomplete all as specified & directed by engr in charge. 164 m&l socket outlet 3 pin5 amps flush type230 voltscomplete all as specified and directed by engr in charge. 165 m&l for socket outlet 2 in 1, 3 pin, 5 & 15 amps, 230 volts t complete all as specified & directed by engr in charge. 166 s&f ceiling rose, surface backelite , three terminal ac, 230 voltcomplete all as specified. 167 supply and fixing led mirror light fitting , type with high out put diffuser 2 feet, 5watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete.havells cat part no enduralinearneobs10wled865spcwh / wipro cat part no ll20 111 xxx 65ne3 / bclsb 10 wh 168 s&f led tube light fitting, 1x 20 22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24 / 0.20 sqmm complete all as specified and directed by engr in charge. make :philips bn021 led 20s psu cw gr s2 / crompton greaves lddr20 cdl dazzle ray / bajaj bclab 20w 169 s&f single pole and neutralenclosure with a two pin and earth plug and socket complete with one single pole mcb 20 amp complete all as specified and as directed by engineer in charge. 170 supply and fixing fan regulator electronicsocket typefive step controlled 230v ac 50 hz forcomplete all as specified and directed by engr in charge. 171 s&f sheet metal enclosure mcb db, double door, tpn 4 way with 200 amps rated busbar all as specified and as directed. make: hegar / legrand / seimens 172 s & f double door, sheet metal enclosure, powder coated for mcb db spn 12 way fittedwith neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to is 13032 1991 complete all as specified and as directed by engr in charge. 173 s & f mcb sp, 5 32 amps , 240 volts, breaking capacity 10ka complete all as specified and as dircted by engr in charge. 174 s&f mcb 63amps, c curve tpn, 415 volts, complete all as specified and as directed by engr in charge. 175 supply and fixing bell push, flush type, 5 amp 230v ac 50 hz forcomplete all as specified and directed by engr in charge. 176 supply and fixing buzzer, ding dong ac. 230 volts, single pole complete all as specified and directed by engr in charge. 177 m & l lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by engr in charge. 178 taking dowen and refixing led light fitting mirror type with high out put diffuser 2 feet, 10 / 5 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete. 179 taking dowen and refixingled tube light fitting, 1x 20 22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24 / 0.20 sqmm complete all as specified and directed by engr in charge. 180 s&f mccb 100 amps, 4 pole, 415 volts, fixed type breaking capacity 16ka complete all as specified and as directed by engr in charge. 181 s&f mccb 40 amps, 4 pole, 415 volts, fixed type breaking capacity 16ka complete all as specified and as directed by engr in charge. 182 s&f in replacement decorative wall light fittings complete made up of polycarbonate, including withfor 9 w led lamp complete all as specified and directed by engr in charge. make / sample approved by engr in charge : surya / havells / phillips 183 s&f in replacement bad side light fitting with suitable led bulb complete all as specified and directed by engr in charge. sample approved by engr in charge and ge . 184 s & f led light fitting 1x9w / 1x10wbulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size. 185 s&f switch piano single pole 5 amps, two way, complete all as specified and as directed by engineer in charge 186 supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230v, 50 hz, rpm 1200, copper winding of sweep 300m 187 m & l for submain ( single phase ) wiring complete with and including 10 sqmm two single core, ( frlsh ) fire retardant, pvc insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, drawn through existing pvc conduitincluding accessories and fixed on walls and10sqmm, fire retardant, pvc insulated, multistranded copper conductor cable for earthing and connected to common earth dolly complete all as specified and as directed by engr in charge. note : ( i ) two runs of10.0 sqmm pvc insulated wire and one run of 10sqmm wire and one run of pvc conduit shall be measured as one unit length. 188 m & l for submain ( single phase ) wiring complete with and including 4.0 sqmm two single core, ( frlsh ) fire retardant, pvc insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, drawn through pvc conduit of suitable size including accessories and fixed on walls and 4 sqmm, fire retardant, pvc insulated, multistranded copper conductor cable for earthing and connected to common earth dolly complete all as specified and as directed by engr in charge. note : ( i ) two runs of 4.0 sqmm pvc insulated wire and one run of 4 sqmm wire and one run of pvc conduit shall be measured as one unit length. 189 s & f mcb spn, 5 32 amps, 240 volts, breaking capacity 16ka complete all as specified and as dircted by engr in charge. 190 m&l for submain wiringusing 4 runs of single core frls pvc insulated, unsheathed stranded copper conductor cable of size 4runs of 10 sqmm of voltage rating 1100v for three phase & neutral, drawn in and including concealed pvc conduit of dia not less than 25 mm dia with standard acessories, along with two run of frls pvc insulated, unsheathed, stranded copper conductor of size 2x6.0 sqmm as earth continuity conductor all as specified and directed ( note 4 runs of single core frls pvc cable 10sqmm for three phase & neutral with two run of earth conductor as earth and conduit shall be measured as one unit ) ...

Ajmer Development Authority - Rajasthan

37187531 tender for repair and maintenance of ac , cooler etc. 1 rewinding of ceiling fan motor ( starting and running winding ) including all necessary material. the motor is to be wound taking no. of coils, turns and pitch as it was originally wound with required size super enamelled wire with e class insulation material and making connections etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. ( new model ceiling fan ) 2 900 / 1200 mm sweep ( new model ceiling fan ) 3 1400 mm sweep ( new model ceiling fan ) 4 all sizes ( old model ceiling fan ) 5 labour charges for removing and refixing of ceiling fan / exaust fanfrom site 6 charges for oiling, overhauling of ceiling fan, table fan, pedestal fan irrespect to the size of fan including removing, refixing of fan from site and testing etc. as required. 7 fans w / o removing & refixing 8 fans with removing & refixing at suitable location 9 p & f aluminium blades ( a set of 3 blades ) duly painted and well finished 900 / 1200 mm. the material of the fan blade shall be of designation 31500b with condition hx6 aluminium alloy sheet confirming to is 737 / 2008 10 p & f aluminium blades ( a set of 3 blades ) duly painted / powder coated. ( 1400 / 1500 mm ) the material of the fan blade shall be of designation 31500b with condition hx6 aluminium alloy sheet confirming to is 737 / 2008 11 p & f of rubber gromet ( fan insulator ) 12 providing and replacement of gun metal bush of ceiling / exhaust / cooler fan / as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 13 p & f 3 speed rotary switch for desert cooler complete with testing etc as required. 14 replacement of cooler pads ( heavy ) setof3 no. of size 25 x 27 15 p & replacement of m.s. shaft of fan motor for desert cooler / exhaust fan. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 16 p & replacement of supporting legs ( 4 no. ) of vertical pump of desert cooler as required for desert cooler / exhaust fan. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 17 p & f of stud with nuts and washer for desert cooler / exhaust fan.all the scrap material should be retained by the contractor. 18 servicing and overhauling of 20 sweep desert cooler including oiling, greasing, painting of tank from inside with rubber paint after properly desmantling each assembly and refixing the same as required. 19 paintingof desert cooler with two coats of rubber paint inside of water tank and two coat of synthetic enamelled paint on both side of cooler body, fan body, grills etc.after cleaning with sand paper, complete in all respect as required. 20 p & f isi marked commercial plywood 4.0 mm thickincluding cutting, hardwares etc. as required. 21 labour chargesfor fixing of desert cooler in windows including handling of cooler upto desired location, making electrical / water connections, testing etc. as required. 22 ground floor 23 first floor 24 p & fof isi marked vertical pump suitable for 20 desert coolerincluding making connection testing etc. as required. isi marked vertical pump 25 p & f of submerciblepump setsuitable for 18 / 24 desert coolers. 26 p & f of submerciblepump setsuitable for 36 desert coolers. 27 p & ffan motor suitable for 20 desert coolerincluding making connection testing etc. as required.with aluminiumwinding motor isi marked 28 rewinding of heavy duty exhaust fan motor including all necessary material, the motor is to be wound taking no. of coils, turns and pitch as it was originally wound with required size super enamelled wire with e class insulation material and making connections etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 29 300 / 380 mm sweep 30 450 mm sweep 31 rewinding of motor of desert cooler pump with super enamelled copper wire, e class insulation material including removing, refixing, testing etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 32 rewinding of motor of desert cooler fan with super enamelled copper wire, e class insulation material including removing, refixing, testing etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 33 providing and replacement of heating element of blower type heat convector as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 34 providing and replacement of heating element rod of radiation type heat convector as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 35 supplying and charging of fresh refrigerant and testing of performance of air conditioner / fridge / water cooler of following capacity including capillary and strainer / filter. 36 1.0 tr window / split a.c. 37 1.5 tr window / split a.c. 38 2.0 tr window / split a.c. 39 25 / 50 / 40 / 80 ltr. water cooler 40 60 / 120 ltr. water cooler 41 replacement of defective compressor by company repaired compressor as per oem recommendationsof following gadgets including testing etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 42 1.0 tr a.c. 43 1.5 tr a.c. 44 2.0 tr a.c. 45 25 / 50 / 40 / 80 ltr. water cooler 46 60 / 120 ltr. water cooler 47 p & replacement of condensing / cooling coil of copper fins for following capacity a.c. / water cooler / fridge as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 48 1.0 tr a.c. 49 1.5 tr a.c. 50 2.0 tr a.c. 51 25 / 50 / 40 / 80 ltr. water cooler 52 60 / 120 ltr. water cooler 53 servicing of 1.0 / 1.5 / 2.0 tr capacity split / window type air conditioner...

Rajasthan Medical Services Corporation Limited - Rajasthan

37044189 supply of trauma centre laryngoscope adult , x ray view box led x ray film view box with 1 film viewer , split air conditioner 1.5 ton 5 star , ups for desktop computer 1kva , multi functional printer laser type , radiology high frequency x ray machine 100ma mobile , bipap mask ventilator well cushioned face mask with ventilator , ambu bag adult and paediatric silicone resuscitators , thomas splint , intubation lma laryngeal mask airway reusable , gauze place bin , kidney tray 8 and 12 , bed pan , ss kick bucket , magles forceps , containers waste collection bins red 1 yellow 1 green 1 and black 1 4 each , cervical collar , forceps set and first aid surgical kit or dressing kit , desktop computer , pulse oxymeter , ot lighting led ot light single dome , mattress and cushion , automated external defibrillators , b type medical oxygen cylinder 40cuft and flow meter or holder , patient stretcher trolleys , a type nitrous oxide cylinder aluminium alloy , artery forceps eriles curved on flat box joint 12 inches , artery forceps eriles curved on flat box joint 15 inches , artery forceps eriles curved on flat box joint 6 inches , artery forceps eriles curved on flat box joint 8 inches , artery forceps eriles straight box joint 6 inches , bed side locker , bone cutting drilling and reaming system , cctv camera surveillance system surveillance camera set 16 cameras 1 dvr set and led tv , dressingdrum , fracture table , icu bed , medicine cabinet , mini laparotomy set , split air conditioner two ton , steriliser forceps cheatle pattern 10 inches , vacuum cleaner wet and dry...

Medical Health And Family Welfare - Rajasthan

37041237 bids are invited for trauma center 1 35 laryngoscope adult , x ray view box led x ray film view box with 1 film viewer , split air conditioner 1.5 ton 5 star , ups for desktop computer 1kva , multi functional printer laser type , radiology high frequency x ray machine 100ma mobile , bipap mask ventilator well cushioned face mask with ventilator , ambu bag adult and paediatric silicone resuscitators , thomas splint , intubation lma laryngeal mask airway reusable , gauze place bin , kidney tray 8 and 12 , bed pan , ss kick bucket , magles forceps , containers waste collection bins red 1 yellow 1 green 1 and black 1 4 each , cervical collar , forceps set and first aid surgical kit or dressing kit , desktop computer , pulse oxymeter , ot lighting led ot light single dome , mattress and cushion , automated external defibrillators , b type medical oxygen cylinder 40cuft and flow meter or holder , patient stretcher trolleys , a type nitrous oxide cylinder aluminium alloy , artery forceps eriles curved on flat box joint 12 inches , artery forceps eriles curved on flat box joint 15 inches , artery forceps eriles curved on flat box joint 6 inches , artery forceps eriles curved on flat box joint 8 inches , artery forceps eriles straight box joint 6 inches , bed side locker , bone cutting drilling and reaming system , cctv camera surveillance system surveillance camera set 16 cameras 1 dvr set and led tv , dressingdrum , fracture table , icu bed , medicine cabinet , mini laparotomy set , split air conditioner two ton , steriliser forceps cheatle pattern 10 inches , vacuum cleaner wet and dry total quantity : 4624...

Department Of Local Bodies - Rajasthan

36994828 rate contract for repair and maintenance of electrical accessories and wiring in nagar nigam buildings. 1 wiring of light point / fan point / exhaust fan point / call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade ( is:694 ) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi marked mms ( is:9537 p iii ) vergin material pvc conduit & its all accessories ( j.b. , bends etc. ) , round tiles, 18 swg g.i. box with earth terminal, 6 a switch , 3 pin ceiling rose / lamp holder / 3 point connector, 3.0 mm thick isi marked phenolic laminated sheet ( is : 2036 1995 ) , al. alloy / cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 . for additional technical parameters of products / work , refer annexure a attached with this bsr . short point ( up to 3 mtr. ) 2 medium point ( up to 6 mtr. ) 3 long point ( up to 10 mtr. ) 4 wiring of 3 / 5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade ( is:694 ) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi marked mms ( is:9537 p iii ) vergin material pvc conduit & its all accessories ( j.b. , bends etc. ) , round tiles, 18 swg g.i. box with earth terminal of required size, 6 a switch, 3 / 5 pin 6 a socket, 3.0 mm thick isi marked phenolic laminated sheet ( is : 2036 1995 ) , al. alloy / cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07. for additional technical parameters of products / work , refer annexure a attached with this bsr . on board 5 short point ( up to 3 mtr. ) 6 medium point ( up to 6 mtr. ) 7 long point ( up to 10 mtr. ) 8 s&f following sizes ( dia. ) of isi marked mms ( is:9537 p iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories ( is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr .mms ( is:9537 p iii ) pvc conduit 25mm 9 mms ( is:9537 p iii ) pvc conduit 32mm 10 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm ) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a or c , flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc / ms conduit / casing capping including all as per pre approved by engineer in charge, making connections, etc. as required. oem must have its own in house nablab setup for all testing facilities for wires. for additional technical parameters of products / work , refer annexure a attached with this bsr .1 x 1.5 sq.mm 11 2 x 1.5 sq.mm 12 1 x 2.5 sq.mm 13 2 x 2.5 sq.mm 14 2 x 4.0 sq.mm 15 supply & drawing wiring for sub mains as per pwd specification for electrical works with isi marked ( is:694 ) , 1100 volts grade pvc insulated flat twin core sheathed solid aluminium conductor with 10 swg g.i. support wire duly clipped including all as per pre approved by engineer in charge, making connections, as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products / work , refer annexure a attached with this bsr . 4.0 sq.mm 16 6.0 sq.mm 17 10.0 sq.mm 18 supplying and laying isi marked p.v.c. insulated submersible cable as per pwd specification for electrical works confirming to is:694 and as per is 8130 : 2013 of 1.1 kv grade .wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm ) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a or c , flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4 including making connection etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. all as per pre approved by engineer in charge, making connections. for additional technical parameters of products / work , refer annexure a attached with this bsr . 2.5 sq.mm 3 core flat / round. 19 providing & fixing of 240 / 415 v ac mcb with positive isolation of breaking capacity not less than 10 ka ( b / c tripping characteristic as per type of load and site requirement ) 4kv impulse withstand voltage, as per pwd specification for electrical works with isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted with existing distribution board / sheets, min. operation 20, 000 upto 32 a rating and 10, 000 upto 63 a, 5000 for 80 a rating including making connections, testing etc. as required. . oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . single pole mcb 6 a to 32 a rating 20 double pole mcb6 a to 32 a rating 21 four pole mcb40 a rating 22 four pole mcb50 63 a rating 23 providing & fixing of ik09 recessed / surface mounting heavy duty horizontal type sheet steel not less then 1.2 mm thick distribution board as per pwd specification for electrical works isi marked conforming to is 13032 & is 8623 / conforming to iec 61439 3. phosphatised / powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar, masking sheet, including making internal db terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . ip 43 double door ( single phase ) . 8 way ( 8 o / g +2 i / c ) 24 ip 43 double door ( three phase ) 8 way ( 24 o / g + 8 i / c ) 25 providing & fixing of isi marked ( is :3854 ) 6 amp. flush type non modular switch as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, minimum width of switch toggle ( push part ) should not less then 16 mm, brass terminal & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 26 providing & fixing of isi marked ( is :3854 ) 16 amp. flush type non modular switch as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material , minimum width of switch toggle ( push part ) should not less then 16 mm, brass terminal & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 27 providing & fixing of of 3 pin 6 amp. flush type non modular socket as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 28 providing & fixing of 3 / 6 pin 16 amp flush type non modular socket as per pwd specification for electrical works, made out fromindustrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 29 providing & fixing of isi marked ( is :3854 ) 6 amp. combined flush type non modular socket and switch set as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, minimum width of switch toggle ( push part ) should not less then 18 mm, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 30 providing & fixing of isi marked ( is :3854 ) 16 amp. combined flush type non modular socket and switch set with indicator and fuse set as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 31 providing and fixing of non modular power plug point accessories as per pwd specification for electrical works with 18 swg g i box of size 175 x 100 x 60 mm with earthing terminal / connector on recessed / surface with suitable size phenolic laminated sheet ( is : 2036 1995 ) cover including cost of 16 amp. switch ( is :3854 ) and 3 / 6 pin 16 amp. socket outlet [ as per detailed in respective item in bsr ] , making connection , testing , etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 32 providing & fixing of isi marked ( is:1293 ) 6 amp unbreakable 3 pin plug top with lamp indicator as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, brass terminal including making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 33 providing & fixing of isi marked ( is:1293 ) 16 amp unbreakable 3 pin plug top with lamp indicator as per pwd specification for electrical works, made out from industrial grade polycarbonate or fire resistant abs material, brass terminal including making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 34 providing & fixing of non modular socket size flush type 120 watt rotary minimum 5 step fan regulator as per pwd specification for electrical works, isi marked ( is:11037 ) made out from industrial grade polycarbonate or fire resistant abs material including making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 35 providing & fixing of isi marked ( is:2268 1994 ) single / multi tone electronic call bell as per pwd specification for electrical works, including making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 36 supply, fixing and testing of following capacity wall mounted stablisers having output voltage variation from 200v to 250v ( + / 5% ) with input voltage variation from 170v to 260v, time delay facility from 2 to 4 minute and high cutoff at 270v complete in all respect e074601 3 kva 37 providing & fixing of ip51 direct or ct operated, 1x240 / 3x240 volts, 50 hz static watt hour meter ( kwh ) as per pwd specification for electrical works, isi marked ( is :13010 2002 ) having resolution 0.1 / 0.01 kwh , accuracy class 1 as per is:13779, led indicators for tamper operation ( reverse & / or earth connection ) , pulsating led indicator for meterology , lcd display, cover plate for body and terminal sealing , push button for all standard parameters, including making connection , testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 10 a to 60 ampere single phase meter. 38 providing & fixing of iso certified company made tp&n 415 v side handle operated double break fuse switch unit in sheet steel enclosure as per pwd specification for electrical works conforming to is / lec 60947 3 : 1999 ( w / o hbc fuses ) including making connections with suitable lugs, testing etc. as required. appropriate type test certificate / oem test report shall be submitted . all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 100 a rating 39 providing & fixing of iso certified company made 240 / 415 v porcelain kitkat fuse ( / hbc type ) as per pwd specification for electrical works conforming to is:2086, 1983 on existing board / sheet including making connections with lugs, testing etc. as required . appropriate type test certificate / oem test report shall be submitted . all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 63 a , 415 v. 40 100 a , 415 v 41 providing & fixing of iso certified company made bus bar chamber housed in sheet metal box as per pwd specification for electrical works confirming to iec 60439 / is 8623 & iec 60529 / is 2147 made out from 1.6 mm thick powder coated crca sheet, degree of protection ip 31 front openable bus bar made out of aluminium or wrought aluminium alloy suitable for 200 amp. capacity , bus bar fixed on porcelain / dmc insulators at approved spacing including making connections etc. as required. appropriate type test certificate / oem test report shall be submitted . all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 300 mm long , 4 strip. 42 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed unarmoured / armoured aluminium cable of 1.1 kv grade as per pwd specification for electrical works in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points ( a ) , ( b ) , ( c ) , mentioned below: ( a ) material : h4 grade aluminium conductor of purity >99.6 % & as per is:1554 p i / is :7098 p – i ( b ) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999 for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 ( part 0 to 64 ) for testing procedures. ( c ) oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities for cables . appropriate type testcertificate / oem test report shall be submitted . all above as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr. e110110 un armoured 16.0 sq. mm 4 core. 43 un armoured25.0 sq. mm 4 core 44 providing & laying of double wall corrugated pipe confirming to is : 14930 p 1 & 2 with hdpe coupler at 1 mtr. depth below the ground for laying cable including making the trench and back filling , compaction of earth as required ( excavation of earth to be paid extra as required. ) of following outer dia. / inner dia as per is:4984:1995. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr .55 / 50 mm. 45 sitc of chemical gel earthing system of dual pipe technology made of with b class g i pipe as per is 1239 ( part 1 ) :2004 of medium duty of following sizes as per points mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : ( a ) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, cpri / erda tested with rms capacity of minimum 35 40 ka for withstanding 1 second . ( b ) to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated lab for low resistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major content as per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts ( c ) heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height 250 to 300 mm. ( d ) testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. ( e ) self certificate for confirming above standards from oem is mandatory. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . e140510 with pipe in pipe technology ( outer pipe dia. / inner pipe dia. ) minimum 100 mm dia borewell gi pipe 2000 mm long, 50 / 25mm, terminal 40mm x 6 mm gi strip. 46 supply & laying following size earth strip in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, jointing shall be done by overlapping and with 2 set of brass ( for custrip ) / gi ( for gi strip ) nut bolt & spring washer spaced at 50cm making connection etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 25mm x 3mm g.i. ( hot dipped ) strip 47 supply & laying following size earth wire in horizontal or verticalrun in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu thimble etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 8 swg copper wire. 48 providing & fixing of iso certified company made bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan as per pwd specification for electrical works, conform to all the performance requirements laid down in is:374 2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) or quality certification such as iso 9001 or above. with down rod up to 30 cm with secondary support. 1200 mm sweep bee 2 star rated ( service value >=4.5 to < 5 ) . 49 providing & fixing of of double ball bearing, copper wounded capacitor start single phase metallic blade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. oem shall be an iso certified company. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 225 mm sweep 50 providing & fixing of heavy duty capacitor start, copper wound double ball bearing 900 / 1400 rpm single phase exhaust fan as per pwd specification for electrical works, conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. oem shall be an iso certified company. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 300 mm sweep ( 900 / 1400 rpm ) . 51 providing & fixing of capacitor start, copper wound, metal body, metal blade three speed wall mounting fan of following sweep with the help of anchor bolts including making connection testing etc. as required. oem shall be an iso certified company. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 400 mm sweep ( oscillating type ) . 52 providing & fixing of fluorscent tube rod in existing fixtures as required complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . flourscent powder coated. 36 / 40 watts. 53 providing & fixing of energy efficient / energy saving ip 20 led direct retrofit bulb in existing holder or fixture as required with system lumen efficacy =100 lm / watt output , pf 0.95 , cri >70, minimum life time of minimum 25000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 / lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product / work, refer annexure a attacheded with this bsr. 9 watt 54 15 watt 55 rewinding of ceiling fan motor ( starting and running winding ) including all necessary material. the motor is to be wound taking no. of coils, turns and pitch as it was originally wound with required size super enamelled wire with e class insulation material and making connections etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. ( new model ceiling fan ) . 900 / 1200 mm sweep ( new model ceiling fan ) 56 labour charges for removing and refixing of ceiling fan / exaust fan from site 57 charges for oiling, overhauling of ceiling fan, table fan, pedestal fan irrespect to the size of fan including removing, refixing of fan from site and testing etc. as required. fans with removing & refixing at suitable location. 58 providing and replacement of ball bearing of ceiling / exhaust fan and refixing the same at suitable location as requiredand as per oem recommendations. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 59 p & replacement of cover / bearing seat of ceiling / exhaust fan. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 60 p & f aluminium blades ( a set of 3 blades ) duly painted and well finished 900 / 1200 mm. the material of the fan blade shall be of designation 31500b with condition hx6 aluminium alloy sheet confirming to is 737 / 2008. 61 servicing and overhauling of 20 sweep desert cooler including oiling, greasing, painting of tank from inside with rubber paint after properly desmantling each assembly and refixing the same as required. 62 painting of desert cooler with two coats of rubber paint inside of water tank and two coat of synthetic enamelled paint on both side of cooler body, fan body, grills etc.after cleaning with sand paper, complete in all respect as required. 63 replacement of cooler pads ( heavy ) set of 3 no. of size 25 x 27 64 p & f aluminiun blade for 20 desert cooler fan as required. 65 p & f of isi marked vertical pump suitable for 20 desert cooler including making connection testing etc. as required. isi marked vertical pump. 66 p & f fan motor suitable for 20 desert cooler including making connection testing etc. as required. with copper winding motor isi marked. 67 rewinding of heavy duty exhaust fan motor including all necessary material, the motor is to be wound taking no. of coils, turns and pitch as it was originally wound with required size supernamelled wire with e class insulation material and making connections etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 300 / 380 mm sweep. 68 rewinding of motor of desert cooler pump with super enamelled copper wire, e class insulation material including removing, refixing, testing etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 69 rewinding of motor of desert cooler fan with super enamelled copper wire, e class insulation material including removing, refixing, testing etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by thecontractor. 70 supplying and charging of fresh refrigerant and testing of performance of air conditioner / fridge / water cooler of following capacity including capillary and strainer / filter. 1.5 tr window / split a.c. 71 2.0 tr window / split a.c. 72 25 / 50 / 40 / 80 ltr. water cooler 73 replacement of defective compressor by company repaired compressor as per oem recommendations of following gadgets including testing etc. as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 1.5 tr a.c. 74 2.0 tr a.c. 75 25 / 50 / 40 / 80 ltr. water cooler 76 p & replacement of condensing / cooling coil of copper fins for following capacity a.c. / water cooler / fridge as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 1.5 tr a.c. 77 2.0 tr a.c. 78 25 / 50 / 40 / 80 ltr. water cooler 79 servicing of 1.0 / 1.5 / 2.0 tr capacity split / window type air conditioner. 80 p & replacement of overload protection of a.c. / water cooler as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 81 p & replacement of thermostat of a.c. / water cooler / fridge as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 82 p & replacement of selector switch of 1.0 / 1.5 / 2.0 tr a.c fan as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 83 p & replacement of starting relay of a.c / water cooler / fridge compressor as required. replacement of material or components shall be use as per guidelines of oem of original product. all the scrap material should be retained by the contractor. 84 s & f of capacitor of 230v / 275v, 50hz rating of plastic casing and terminals lugs or copper wire. starting capacitor.40 60 micro farad. 85 60 80 micro farad. 86 running capacitor 2.5 / 3.15 micro farad. 87 4.0 micro farad 88 6.0 micro farad 89 8.0 micro farad 90 10.0 micro farad 91 providing & fixing of ip20 led surface / recessed / suspended mounting mid power smd type led light fixture made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 2.5 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection and in compliance to iec standards ( integral with light fixture ) . system lumen efficacy min. 100 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl acredeated lab setup for all testing facilities for led fixtures. ( lm79 / lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . for additional technical parameters of product / work, refer annexure a attacheded with this bsr. recessed mounting 48w led light fixture 2x2 with acrylic / prismatic front cover. 92 gas charging of vrf / vrv system with r410a refrigerant gas. before gas charging system shall be flushed with high purity nitrogen gas to remove carbon content, dirt particles to make sure that there is no chance of mixing any impurity with refrigerant gas. thereafter system shall be tested with nitrogen gas at 1.5 times of working pressure of r410 refrigerant gas to ensure leakproof system. whole system shall be vacuumed up to 500 micron level which ensures the zero moisture content level in piping to ensure better cooling efficiency and long life of the system. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr ....

Pradhan Mantri Gram Sadak Yojana - Rajasthan

36595163 tender for construction & maintenance pkg. no. rj06p316 t 13 bachhamadi to nh 21 via nagla bartai march, 2023 2 construction of reference bench mark ( 1 no. ) , working bench mark ( 4 nos. ) and near all drainage structures and bridges ( as per direction of engineer in charge ) , reference pillar / burgees @ 50m interval on both side of formation width including marking of centre line, setting out curves, recording of levels, white washing and lettering etc. complete as per mord specifications cl. 108. 3 clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlierand disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per mord specification clause 201.by mechanical means in area of non thorny jungle 4 scarifying old bituminous road by making 50x50mm furrows criss cross at 1.0 metre intervals at 45 degree to the center line of the carriageway 5 excavation for roadwork in soil with hydraulic excavator of0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per mord specification clause 302.3 6 construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of tables 300.1 and 300.2 with a lead upto 50 m as per mord specification clause 301.5 7 construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m as per mord specification clause 303.1. 8 construction of granular sub base by providing well graded material, mixing in a mechanical mix plant at omc , carriage of mixed material to work site upto lead of 1000m spreading in uniform layers with tractor mount grader on prepared surface, mixing by mix in place method with rotavatorat omc, and compacting with smoothwheelroller to achieve thedesired density, complete as per mord specification clause 401. for grading i material 9 providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing thematerial with water at omc in mechanical mixer ( pug mill ) , carriage of mixed material by tipper to site, layingin uniform layers in sub base / base course on a well prepared sub base and compacting with smoothwheel roller of 80 to 100kn weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per tables 400.11 & 400.12 and mord specification clause 406. extra rate for carriage of mixed material additional lead of 20 km from in item 4.9 10 providing and applying primer coat with bitumen emulsion ( ss 1 ) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 1.0 kg / sqm using mechanical means as per mord specification clause 502. low porosity 11 providing and applying tack coat with bitumen emulsion ( rs 1 ) using emulsiondistributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with hydraulic broom as per mord specification clause 503. 12 providing and laying bituminous macadam with hot mix plant using crushed aggregates ofgrading as per table 500.4 premixed with bituminous binder, transported to site with all leads laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolledto achieve the desired compaction as per mord specification clause 504.bitumen ( vg 30 ) 13 providing, laying and rolling of open graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing of aggregate and plastic waste cutting in a hotmix plant, laying and rolling with a three wheel 80 100 kn static roller capacity, finished to required level and grades to be followed by seal coat of either type a or type b or type c as per mord specification clause 508. waste plastic @ 8% of bitumen. case ii by mechnical meansbitumen vg 30 14 providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using type a, type b and type c as per mord specification clause 510 by mechanical means case ii:type b bitumen ( vg 30 ) 15 supply & planting of shady plants ( neem, peepal, goolar, jamun, imli or other specified ) along road side including the following activities: 1. preparation of soil including cleaning & removing of unwanted shrubs removal of stones & garbage. 2. supply of plant at site of two years of age & height more than 1.50 mtr 3. supply of dry manure ( farm yard manure organic ) 4. supply of insecticides 5. digging of pits size 60x60x60 cms. including removal of stones. manuring application of insecticides & watering at least 15 liter per plant after planting. 6. half brick circular tree guard in second class bricks, internal dia 1.25 meter and height 1.20 meter above ground and 0.20 meter below ground, bottom two courses laid dry and top three courses in cement mortar 1:6 ( 1cement : 6 sand ) and the intermediate courses being in dry honey comb masonry, as per design complete. 16 construction of foundation / inaugration pedastal in 23 cm thick brick masonry in cm 1:4 of size 1.20m x 1.80m above ground level with adequate foundation including providing and fixing of granite stone of size 0.75m x0.60m with engraving letters and figures, cement plaster, white washing etc. complete as per direction of engineer in charge. 17 providing and fixing of retro reflectorised cautionary, mandatory and informatory sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as perdrawings and mord specification clause 801 18 900 mm equilateral & triangle 19 600 mm circular 20 800 mm x 600 mm rectangular 21 providing and fixing of typical pmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges.the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly embedded in cement concrete m 15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level.the top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 swg steel plate tube.all m.s. will be stove enameled on both sides.lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour.all sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing clause 1701 and annexure 1700.1 22 providing and fixing of pmgsy logo with definition plate ( as per mord design / drawing ) 2mm thick ms plate framed to angle iron 40x40x6mmincluding orange luminous colour paint on logo, size of diamand plate 600x600mm definition plate 900x250mm supported on ms post of angle iron of size 65x65x6mm, 3m long stove enameled paint with hold fastfirmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and mord specification clause 1700 23 providing and erecting direction and place identification retro reflectorised sign asper irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3, fixed over aluminium sheeting, 2 mm thickwith areaexceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 nos.firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and mord specification clause 1701 24 providing and erecting typical citizens information board as per approved drawing & specification of mord made of two ms sheet of 1.6 mm thick each of size 900mm x 750mm stiffend by angle iron 25mmx25mm x 3mm all around the plate & plates fixed on frame of 75mm dia pipe of 12 swg sheet ( vertical post 3050 mm with angle holdfasts and horizontal member 900mm ) to be joined by embedded in cement concrete m 15 grade of block of 600mmx 600mm x 750 mm size below ground level as per enclosed drawings & as directed by engineering incharge. all ms will be stove anmeled on both side lettering. figuring and border will be with ready mixed synthethic enamel paint of superior quality in required shade and colour etc complete in all respect. all sections of framed post and steel tube will be painted with primer and two coat of epoxy paint as per drawing and as per mord specification. 25 reinforced cement concrete m15grade kilometre stone / local stone of standard design as per irc:8 fixing in position including painting and printing, etc as per drawing and mord specification clause 1703 26 ( a ) 5th kilometre stone ( precast ) 27 ( b ) ordinary kilometer stone ( precast ) 28 ( c ) 200 m stone ( precast ) 29 cut stone boundary pillars / local stone of standard design as per irc:25, fixed in position including finishing and lettering but excluding painting as per drawing and technical specification clause 1704 30 providing and laying rounded hump type speed breakers for crossing speed 25 km / h as per irc design including providing and applying bitumen emulsion tack coat, making speed breaker in designed profile with bituminous macadam, providing seal coat type b for sealing the voids and marking chequered pattern with thermoplastic paint complete as perirc : 99 1988 31 marking centre line and stop lines etc. on road as per irc pattern with thermoplastic paint of approved quality and make without glass beads laid on the road surface at temperature 160 c with a special applicator machine complete with a special applicator machine complete with labour material and traffic diversion arrangements. 32 providing and erecting typical maintenance information board as per approved drawing & specification of mord made of ms sheet of 1.6 mm thick of size 900mm x 1500mm stiffend by angle iron 25mmx25mm x 3mm all around the plate & plates fixed on frame of 75mm dia pipe of 12 swg sheet ( vertical post 3050 mm with angle holdfasts and horizontal member 900mm ) to be joined by embedded in cement concrete m 15 grade of block of 600mmx 600mm x 750 mm size below ground level as per enclosed drawings & as directed by engineering incharge. all ms will be stove anmeled on both side lettering. figuring and border will be with ready mixed synthethic enamel paint of superior quality in required shade and colour etc complete in all respect. all sections of framed post and steel tube will be painted with primer and two coat of epoxy paint as per drawing and as per mord specification. 33 providing and fixing of road stud 100 x 100 mm die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per bs:873 ( part 4 ) 1973. 34 supply & fixing of mandatory / regulatory reflective sign board fixed on 3 meter long angle iron of size 65x65x6 mm complete as per irc 67 1977 made of 2 mm thick m.s. sheet stove enamelled paint and reflective symbol. 35 stop signs with definition plate size 30x20 cm 90 cm octagon 36 60 cm octagon 37 supply of caution diversion sign board size 1800 x 600 mm having centre height of 75 cm made out or 1.25 mm thick m.s. sheet duly framed with angle iron size 40 x 40 x 5 mm fixed on two moving wheels and stands, made out of 75 x 40 mm channel having two solid rubber wheels mounted on ball bearings, boards is processed in stoving enamel blue and machine cut sheet reflective letter and arrow on one side and the other side having arrow only complete in all respect. 38 supplying & fixing route marker reflective sign boards consisting of shield marked on m.s. flat 14 gauge of size 40 x 60 cm and definition plate of 30 x 25 cm, 14 gauge, fixed on mild steel posts of t iron or angle iron for nh / sh : 39 supplying of men at work sign board ( folding type ) made of 1.25 mm thick m.s. sheet size 900x900x900 mm painted in white stove enamelled paint and reflective machine cut sheet men’s emblem and letter men at work in red colours and additional attachment of size 150x900 mm plate for gang number and name with white stoving enameled back ground both plates are fixed on a folding stand of m.s. ( heavy ) steel tube of size 13.2 mm outer dia as per is 1239 ( part i ) 1979 duly painted in grey colour and both the plates are painted on back side in grey enamel paint. 40 p & f delinator with 30 cm. outer dia rcc hume pipe np 2 ( as per is 458 / 1971 ) pipe 1. om. long 40 cm embedded in cement concrete ( 1:4:8 ) block of size 50x50x40 cm. including excavation upto 40 cm depth. the inside of pipe shall be filled with c.c. ( 1:4:8 ) stone grit max size 20 mm or less upto the top with semi circular humping. the pipes shall be painted white / black with enamel paint with red dots two nos. on each side 41 supplying of cat’s eye made of aluminium alloy size 75x100x22 mm having 21 biconvex lenses embedded in circular disk of abs plastic on each side. 42 providing and erecting a thrie metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 85 cm above road / ground level, fixed on ismc series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 2 m high with 1.15 m below ground level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to is:1367 and is:1364, metal beam rail to be fixed on the vertical post with a space of channel section 150 x 75 x 5 mm, 546 mm long complete as per clause 810 43 supply of chevron sign of size 75x60 cm made out of aluminum sheet 2 mm thick with fixing provision on m.s. angle iron post 50x50x6 mm 3 m long screwed with stainless steel nut bolts of 8 m dia, plate is covered by high intensity grade yellow retro reflective sheeting and black screen printed arrow on retro reflective sheet, complete in all respect. comp. in all respect duly post painted in alternate band of black / white synthetic enamel paint & hold fast at bottom 44 earthwork in excavation for structures as per drawing and mord specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitablematerial.ordinary soil upto 3 m depth 45 providing concrete for plain / reinforced concrete in open foundations complete as per drawings and mord specifications clause 802, 803, 1202 & 1203 p.c.c grade m 10 nominal mix 1:3:6 46 stone masonry in cement mortar for substructure complete as per drawing & mord specification clauses 702, 704, 1202 and 1204 random rubble masonry in 1:6 cement mortar 47 providing pcc m 20 architectural coping on the top of wing wall, return wall etc. complete as per drawing and mord specification clauses 615, 710and 1204.3.11 75 mm thick 48 pointing with cement mortar ( 1:3 ) on stone work as per drawing and mord specification clauses 613.3 and 1204 flush and rulled type 49 construction of dry lean cement concrete sub base over a prepared sub grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600 1, cement content not to be less than 150 kg / cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8 10 tonnes vibratory roller, finishing and curing. 50 construction of plastic cell filled cement concrete pavement, with m30 grade concrete, thickness as per design, over a prepared sub base, with 53 grade ordinary portland cement ( opc ) or any other type as per clause 1501.2.4 m30 ( grade ) .coarse and fine aggregates conforming to is : 2386, maximum in a concrete mixer of not less then 0.2 cum capacity and appropriate weigh batcher using approved mix design ( as per irc 44 2088, laid in approved fixed side formwork ( steel channel, wedges, steel plates including levelling the formwork as per drawing ) , spreading the concrete with shovels, rakes, compacted using screed and plate vibrators and finished in continuous operation, concrete should have a slump of 30 50mm with use of approved plasticizer if required formwork of plastic cells should be made of high density polyethylene ( hdpe ) , sheets having thickness ranging from 0.19 0.22mm with sides 150mmx150mm and height as fixed by engineer in charge. to be laid in full width of the carriageway. iron spikes of about 200mm long are to be used to keep the cell walls taut. nylon thread or rope may be used to preventcollapse of cells during placement of concrete. iron spikes to be taken out for use in other place as soon as the concrete is in place. curing of concrete slabs for 14 days, curing compound ( where specified ) and water finishing to lines and grade as per drawing and mord specification of cell filled concrete pavement.150mm thickness 51 providing and laying reinforced cement concrete pipe np3 for culverts on first class bedding of granularmaterial in single row includingfixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets clause 1106.np3 pipes 300 mm dia 52 routine maintenance work after completiion of works for five years fixed amount....

Medical Health And Family Welfare - Rajasthan

36433514 electrical work in the construction of phc building at badka ( laxmangarh ) distt. alwar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 medium point ( up to 6 mtr. ) 8 long point ( up to 10 mtr. ) 9 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 10 on board 11 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 12 20 mm 13 25 mm 14 32 mm 15 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 16 1 x 1.5 sq.mm 17 3x 1.5 sq.mm 18 2 x 2.5 sq. mm. + 1x1.5sqmm 19 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 20 4 x 10.0 sq.mm 21 4 x 6.0 sq.mm 22 1 x 4.0 sq.mm 23 1 x 2.5 sq.mm 24 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. 25 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 26 2 pair 27 p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.for additional technical parameters of product / work refer annexure a attached with this bsr 28 40mm x 40mm x 5mm 29 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 30 6.4 mm thick 31 p & f phenolic laminated sheet 2.0 mm thick of following size . including screws, cup washer as required.for additional technical parameters of product / work refer annexure a attached with this bsr 32 75 mm dia 33 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 34 single pole mcb ( with b / c curve tripping characteristics ) 35 6 a to 32 a rating 36 double pole mcb ( with b / c curve tripping characteristics ) 37 6 a to 32 a rating 38 four pole mcb ( with b / c curve tripping characteristics ) 39 6 a to 32 a rating 40 50 / 63 a rating 41 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 42 metal door ( single phase ) ik 09 and ip 43 with metal end box 43 16 way ( 16+2 ) 44 metal door ( three phase ) ik 09 and ip 43with metal end box 45 6 way 46 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 47 20 amp, 3 pin + scrapping earth, 4 module 48 p & f of industrial plug and socket conforming to iec 60309 1 / 2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. for additional technical parameters of product / work refer annexure a attached with this bsr 49 ip 67 panel mounted socket 50 32 a 3 pin ( 2p+e ) 51 providing & fixing of flush typenon modular single line telephone jackmade out fromindustrial grade polycarbonate or fire resistant abs material, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 52 providing & fixing of ding dong / musical chime bell as per pwd specification for electrical works, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 54 5 step fan regulator 2 module 360 dgree rotating 55 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 56 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 57 10 pairs 58 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 59 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 60 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 61 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 62 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 63 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 64 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 65 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 66 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 67 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 68 electrolytic grade aluminium bus bar 6010 grade 69 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 70 ring type tape wound ct 71 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 72 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 73 red / yellow / green colour 74 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 3.3 kv, class a 2 mm thick with proof voltage 10 kv ac ( rms ) and break down voltage 30 kv ac ( rms ) 76 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 77 4 pole mccb with thermal magnetic release 78 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 79 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 80 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 open execution type 82 160 a 83 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 84 10.0 sq. mm 85 2 core 86 35.0 sq. mm 87 3.5 core 88 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 89 3.5 x 35.0 sq.mm 90 supplying and makingend termination with heavy aluminiumlugs ( pin / ring type ) confirming to is 8309 1993 & is 8337 1976 duly crimped with crimping tool, pvc tape etc of following size.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 91 35.0 sq.mm 92 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 93 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 94 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 95 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 96 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 97 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 98 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 17.2 mm thick and 3 mtr. long 100 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 8 swg copper wire 102 8 swg g.i. ( hot dipped ) wire 103 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 up to 457 mm size 105 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 106 1200 mm sweep bee 2 star rated ( service value >=4.5 to < 5 ) 107 1200 mm sweep bee 3 star rated ( service value >=5.0 to< 5.5 ) 108 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 109 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 110 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 111 225 mm sweep 112 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 113 300 mm sweep ( 900 / 1400 rpm ) 114 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 450 mm sweep wall mounting and three speed regulator with minimum air delivery 150 cum. / minute 116 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 up to 380 mm size 118 providing & fixing of vertical ( bee 5 star rated ) / horizontal ( bee 3 star rated ) storage water heater with outer casing made of engineering plastic sheet ( upto 25 ltr ) / metal rust proof body ( 35 & 50 ltr ) , glass line / titanium enamel coated pressure pump compatible 8 bar pressure inner tank, glass line coated , mineral filled heating element, stem type, snap actionadjustable thermostat , dual indicating lampsinjected puf insulation, multi function valve etc. as required held in position with 2 / 4 no. 10 / 12 mm anchor fastener, duly wired with 3 core 2.5 / 4.0 sqmm pvc insulated & sheathed copper conductor and 16 a / 25a three pin plug top with portable residual current device ( prcd ) , including making inlet, outlet flexible alloyconnection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 119 15 ltr. 120 sitc ofmnre approved & confirming to is:12933 p 1, 2, 3 & 5 flat plate collector type solar hot water system havingcollector withzincalum sheet outer body , glass line / titanium enamel coated inner tank with metal rust proof puf insulated body includingelectrical back up, thermostat, powder coated / hot dipped galvanized ms standfor collector & tank etc. as required. of following capacity complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 121 200 litre / day 122 providing & fixing of energy efficient direct fit ( retrofit ) polycarbonate / glasshousingsmd mid power led tube rod ( with integral driver & alumn. heat sink ) , on existing fixture.system lumen efficacy = 100 lm / watt output, internal surge protection of 2.5 kv , thd < 20% , p.f.=0.95, cri >80 , life time of minimum35000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 123 1200mm , min. lumens output 2000 lmled tube rod with polycarbonate housing 124 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 125 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 126 surface mounting ( with extruded alumn. housing ) 127 minimum lumen output 1950 lm 128 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 129 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 130 recessed mounting 131 minimum lumen output 4200 lm 132 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 led street light fixture with minimum lumen output 2450 lm 134 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 135 25 mm dia. 136 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 138 cat 6, un sheilded information outlet 139 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 single aperture 141 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 142 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 143 1 mtr 144 supply, installation, & testing of 19 1u rack mounted / surface mounted aluminum / crca 1.2mm powder coated, multimode glass fiber optic cable patch panel / liu loaded with flangless / screwable adapters for st / e 2000 / sc / lc / mt rj / pc type, it should have easy removable top plate with push buttons, there should be a splice tray installed in the patch panel / liu which can handle the fiber cores, splice tray should be pc+abs material, it should include accessories like mounting hardware, gormetts, heat shrink tubes / sleevs, screws, nuts to install the panel for rack / wallmount applications as per requirement complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 multi mode liu 12 ports 146 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 6 u rack with width 600 mm &depth 400 mm + 100 mm 148 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 149 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 1.0 hp, 1 ø, ( 7 12 ) mtr, ( 405 240 ) lpm 151 sitc of monoblock motor pump set isi marked ( is:9079 2002 ) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single / three phase ( 240 440 v ) permanent split capacitor type ( psc ) , fitted with thermal overload protection, including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 1.0 hp, 1 ø, ( 10 120 ) mtr, ( 30 12 ) lpm 153 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 154 1.5 tr iseer not less then 3.8 155 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 156 25 mm 157 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 4 kva 159 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 160 150 mm dia per running inch length 161 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 162 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 163 4 kg...

Medical Health And Family Welfare - Rajasthan

36432928 electrical work in the construction of phc building at duhar chougan ( thanagazi ) distt. alwar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 medium point ( up to 6 mtr. ) 8 long point ( up to 10 mtr. ) 9 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 10 on board 11 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 12 20 mm 13 25 mm 14 32 mm 15 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 16 1 x 1.5 sq.mm 17 3x 1.5 sq.mm 18 2 x 2.5 sq. mm. + 1x1.5sqmm 19 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 20 4 x 10.0 sq.mm 21 4 x 6.0 sq.mm 22 1 x 4.0 sq.mm 23 1 x 2.5 sq.mm 24 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. 25 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 26 2 pair 27 p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.for additional technical parameters of product / work refer annexure a attached with this bsr 28 40mm x 40mm x 5mm 29 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 30 6.4 mm thick 31 p & f phenolic laminated sheet 2.0 mm thick of following size . including screws, cup washer as required.for additional technical parameters of product / work refer annexure a attached with this bsr 32 75 mm dia 33 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 34 single pole mcb ( with b / c curve tripping characteristics ) 35 6 a to 32 a rating 36 double pole mcb ( with b / c curve tripping characteristics ) 37 6 a to 32 a rating 38 four pole mcb ( with b / c curve tripping characteristics ) 39 6 a to 32 a rating 40 50 / 63 a rating 41 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 42 metal door ( single phase ) ik 09 and ip 43 with metal end box 43 16 way ( 16+2 ) 44 metal door ( three phase ) ik 09 and ip 43with metal end box 45 6 way 46 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 47 20 amp, 3 pin + scrapping earth, 4 module 48 p & f of industrial plug and socket conforming to iec 60309 1 / 2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. for additional technical parameters of product / work refer annexure a attached with this bsr 49 ip 67 panel mounted socket 50 32 a 3 pin ( 2p+e ) 51 providing & fixing of flush typenon modular single line telephone jackmade out fromindustrial grade polycarbonate or fire resistant abs material, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 52 providing & fixing of ding dong / musical chime bell as per pwd specification for electrical works, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 54 5 step fan regulator 2 module 360 dgree rotating 55 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 56 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 57 10 pairs 58 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 59 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 60 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 61 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 62 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 63 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 64 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 65 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 66 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 67 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 68 electrolytic grade aluminium bus bar 6010 grade 69 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 70 ring type tape wound ct 71 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 72 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 73 red / yellow / green colour 74 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 3.3 kv, class a 2 mm thick with proof voltage 10 kv ac ( rms ) and break down voltage 30 kv ac ( rms ) 76 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 77 4 pole mccb with thermal magnetic release 78 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 79 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 80 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 open execution type 82 160 a 83 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 84 10.0 sq. mm 85 2 core 86 35.0 sq. mm 87 3.5 core 88 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 89 3.5 x 35.0 sq.mm 90 supplying and makingend termination with heavy aluminiumlugs ( pin / ring type ) confirming to is 8309 1993 & is 8337 1976 duly crimped with crimping tool, pvc tape etc of following size.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 91 35.0 sq.mm 92 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 93 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 94 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 95 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 96 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 97 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 98 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 17.2 mm thick and 3 mtr. long 100 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 8 swg copper wire 102 8 swg g.i. ( hot dipped ) wire 103 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 up to 457 mm size 105 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 106 1200 mm sweep bee 2 star rated ( service value >=4.5 to < 5 ) 107 1200 mm sweep bee 3 star rated ( service value >=5.0 to< 5.5 ) 108 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 109 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 110 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 111 225 mm sweep 112 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 113 300 mm sweep ( 900 / 1400 rpm ) 114 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 450 mm sweep wall mounting and three speed regulator with minimum air delivery 150 cum. / minute 116 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 up to 380 mm size 118 providing & fixing of vertical ( bee 5 star rated ) / horizontal ( bee 3 star rated ) storage water heater with outer casing made of engineering plastic sheet ( upto 25 ltr ) / metal rust proof body ( 35 & 50 ltr ) , glass line / titanium enamel coated pressure pump compatible 8 bar pressure inner tank, glass line coated , mineral filled heating element, stem type, snap actionadjustable thermostat , dual indicating lampsinjected puf insulation, multi function valve etc. as required held in position with 2 / 4 no. 10 / 12 mm anchor fastener, duly wired with 3 core 2.5 / 4.0 sqmm pvc insulated & sheathed copper conductor and 16 a / 25a three pin plug top with portable residual current device ( prcd ) , including making inlet, outlet flexible alloyconnection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 119 15 ltr. 120 sitc ofmnre approved & confirming to is:12933 p 1, 2, 3 & 5 flat plate collector type solar hot water system havingcollector withzincalum sheet outer body , glass line / titanium enamel coated inner tank with metal rust proof puf insulated body includingelectrical back up, thermostat, powder coated / hot dipped galvanized ms standfor collector & tank etc. as required. of following capacity complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 121 200 litre / day 122 providing & fixing of energy efficient direct fit ( retrofit ) polycarbonate / glasshousingsmd mid power led tube rod ( with integral driver & alumn. heat sink ) , on existing fixture.system lumen efficacy = 100 lm / watt output, internal surge protection of 2.5 kv , thd < 20% , p.f.=0.95, cri >80 , life time of minimum35000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 123 1200mm , min. lumens output 2000 lmled tube rod with polycarbonate housing 124 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 125 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 126 surface mounting ( with extruded alumn. housing ) 127 minimum lumen output 1950 lm 128 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 129 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 130 recessed mounting 131 minimum lumen output 4200 lm 132 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 led street light fixture with minimum lumen output 2450 lm 134 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 135 25 mm dia. 136 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 138 cat 6, un sheilded information outlet 139 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 single aperture 141 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 142 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 143 1 mtr 144 supply, installation, & testing of 19 1u rack mounted / surface mounted aluminum / crca 1.2mm powder coated, multimode glass fiber optic cable patch panel / liu loaded with flangless / screwable adapters for st / e 2000 / sc / lc / mt rj / pc type, it should have easy removable top plate with push buttons, there should be a splice tray installed in the patch panel / liu which can handle the fiber cores, splice tray should be pc+abs material, it should include accessories like mounting hardware, gormetts, heat shrink tubes / sleevs, screws, nuts to install the panel for rack / wallmount applications as per requirement complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 multi mode liu 12 ports 146 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 6 u rack with width 600 mm &depth 400 mm + 100 mm 148 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 149 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 1.0 hp, 1 ø, ( 7 12 ) mtr, ( 405 240 ) lpm 151 sitc of monoblock motor pump set isi marked ( is:9079 2002 ) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single / three phase ( 240 440 v ) permanent split capacitor type ( psc ) , fitted with thermal overload protection, including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 1.0 hp, 1 ø, ( 10 120 ) mtr, ( 30 12 ) lpm 153 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 154 1.5 tr iseer not less then 3.8 155 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 156 25 mm 157 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 4 kva 159 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 160 150 mm dia per running inch length 161 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 162 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 163 4 kg...

Medical Health And Family Welfare - Rajasthan

36432910 tender for electrical work in the construction of phc building at basai jogiyan ( thangagazi ) distt. alwar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 medium point ( up to 6 mtr. ) 8 long point ( up to 10 mtr. ) 9 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 10 on board 11 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 12 20 mm 13 25 mm 14 32 mm 15 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 16 1 x 1.5 sq.mm 17 3x 1.5 sq.mm 18 2 x 2.5 sq. mm. + 1x1.5sqmm 19 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 20 4 x 10.0 sq.mm 21 4 x 6.0 sq.mm 22 1 x 4.0 sq.mm 23 1 x 2.5 sq.mm 24 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. 25 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 26 2 pair 27 p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.for additional technical parameters of product / work refer annexure a attached with this bsr 28 40mm x 40mm x 5mm 29 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 30 6.4 mm thick 31 p & f phenolic laminated sheet 2.0 mm thick of following size . including screws, cup washer as required.for additional technical parameters of product / work refer annexure a attached with this bsr 32 75 mm dia 33 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 34 single pole mcb ( with b / c curve tripping characteristics ) 35 6 a to 32 a rating 36 double pole mcb ( with b / c curve tripping characteristics ) 37 6 a to 32 a rating 38 four pole mcb ( with b / c curve tripping characteristics ) 39 6 a to 32 a rating 40 50 / 63 a rating 41 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 42 metal door ( single phase ) ik 09 and ip 43 with metal end box 43 16 way ( 16+2 ) 44 metal door ( three phase ) ik 09 and ip 43with metal end box 45 6 way 46 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 47 20 amp, 3 pin + scrapping earth, 4 module 48 p & f of industrial plug and socket conforming to iec 60309 1 / 2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. for additional technical parameters of product / work refer annexure a attached with this bsr 49 ip 67 panel mounted socket 50 32 a 3 pin ( 2p+e ) 51 providing & fixing of flush typenon modular single line telephone jackmade out fromindustrial grade polycarbonate or fire resistant abs material, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 52 providing & fixing of ding dong / musical chime bell as per pwd specification for electrical works, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 54 5 step fan regulator 2 module 360 dgree rotating 55 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 56 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 57 10 pairs 58 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 59 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 60 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 61 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 62 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 63 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 64 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 65 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 66 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 67 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 68 electrolytic grade aluminium bus bar 6010 grade 69 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 70 ring type tape wound ct 71 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 72 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 73 red / yellow / green colour 74 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 3.3 kv, class a 2 mm thick with proof voltage 10 kv ac ( rms ) and break down voltage 30 kv ac ( rms ) 76 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 77 4 pole mccb with thermal magnetic release 78 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 79 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 80 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 open execution type 82 160 a 83 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 84 10.0 sq. mm 85 2 core 86 35.0 sq. mm 87 3.5 core 88 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 89 3.5 x 35.0 sq.mm 90 supplying and makingend termination with heavy aluminiumlugs ( pin / ring type ) confirming to is 8309 1993 & is 8337 1976 duly crimped with crimping tool, pvc tape etc of following size.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 91 35.0 sq.mm 92 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 93 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 94 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 95 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 96 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 97 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 98 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 17.2 mm thick and 3 mtr. long 100 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 8 swg copper wire 102 8 swg g.i. ( hot dipped ) wire 103 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 up to 457 mm size 105 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 106 1200 mm sweep bee 2 star rated ( service value >=4.5 to < 5 ) 107 1200 mm sweep bee 3 star rated ( service value >=5.0 to< 5.5 ) 108 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 109 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 110 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 111 225 mm sweep 112 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 113 300 mm sweep ( 900 / 1400 rpm ) 114 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 450 mm sweep wall mounting and three speed regulator with minimum air delivery 150 cum. / minute 116 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 up to 380 mm size 118 providing & fixing of vertical ( bee 5 star rated ) / horizontal ( bee 3 star rated ) storage water heater with outer casing made of engineering plastic sheet ( upto 25 ltr ) / metal rust proof body ( 35 & 50 ltr ) , glass line / titanium enamel coated pressure pump compatible 8 bar pressure inner tank, glass line coated , mineral filled heating element, stem type, snap actionadjustable thermostat , dual indicating lampsinjected puf insulation, multi function valve etc. as required held in position with 2 / 4 no. 10 / 12 mm anchor fastener, duly wired with 3 core 2.5 / 4.0 sqmm pvc insulated & sheathed copper conductor and 16 a / 25a three pin plug top with portable residual current device ( prcd ) , including making inlet, outlet flexible alloyconnection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 119 15 ltr. 120 sitc ofmnre approved & confirming to is:12933 p 1, 2, 3 & 5 flat plate collector type solar hot water system havingcollector withzincalum sheet outer body , glass line / titanium enamel coated inner tank with metal rust proof puf insulated body includingelectrical back up, thermostat, powder coated / hot dipped galvanized ms standfor collector & tank etc. as required. of following capacity complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 121 200 litre / day 122 providing & fixing of energy efficient direct fit ( retrofit ) polycarbonate / glasshousingsmd mid power led tube rod ( with integral driver & alumn. heat sink ) , on existing fixture.system lumen efficacy = 100 lm / watt output, internal surge protection of 2.5 kv , thd < 20% , p.f.=0.95, cri >80 , life time of minimum35000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 123 1200mm , min. lumens output 2000 lmled tube rod with polycarbonate housing 124 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 125 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 126 surface mounting ( with extruded alumn. housing ) 127 minimum lumen output 1950 lm 128 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 129 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 130 recessed mounting 131 minimum lumen output 4200 lm 132 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 led street light fixture with minimum lumen output 2450 lm 134 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 135 25 mm dia. 136 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 138 cat 6, un sheilded information outlet 139 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 single aperture 141 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 142 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 143 1 mtr 144 supply, installation, & testing of 19 1u rack mounted / surface mounted aluminum / crca 1.2mm powder coated, multimode glass fiber optic cable patch panel / liu loaded with flangless / screwable adapters for st / e 2000 / sc / lc / mt rj / pc type, it should have easy removable top plate with push buttons, there should be a splice tray installed in the patch panel / liu which can handle the fiber cores, splice tray should be pc+abs material, it should include accessories like mounting hardware, gormetts, heat shrink tubes / sleevs, screws, nuts to install the panel for rack / wallmount applications as per requirement complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 multi mode liu 12 ports 146 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 6 u rack with width 600 mm &depth 400 mm + 100 mm 148 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 149 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 1.0 hp, 1 ø, ( 7 12 ) mtr, ( 405 240 ) lpm 151 sitc of monoblock motor pump set isi marked ( is:9079 2002 ) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single / three phase ( 240 440 v ) permanent split capacitor type ( psc ) , fitted with thermal overload protection, including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 1.0 hp, 1 ø, ( 10 120 ) mtr, ( 30 12 ) lpm 153 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 154 1.5 tr iseer not less then 3.8 155 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 156 25 mm 157 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 4 kva 159 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 160 150 mm dia per running inch length 161 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 162 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr ....

Public Works Department - Rajasthan

36408724 tender for electrical work in govt. srg hospital jhalawar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) on surface isi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface moulded virgin materialupvcmodular box , 10 a modular switch, modular faceplate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required. for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 2 short point ( up to 3 mtr. ) 3 medium point ( up to 6 mtr. ) 4 long point ( up to 10 mtr. ) 5 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) of approved make on surfaceisi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface 2 no. moulded virgin materialupvcmodular box , 2 nos 10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 6 medium point ( up to 6 mtr. ) 7 long point ( up to 10 mtr.. ) 8 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) on surfaceisi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface moulded virgin materialupvcmodular box, modular 10a switch, 3 / 5 pin6 amodular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 9 on board 10 s&f following sizesof isi marked ( is:14927 p ii ) virgin materialupvc trunking along with accessorieslike coupler, inner, outer, elbow, square box, tee, end cap etc. on surfacewithscrews, expansionfastenersas required. for additional technical parameters of product / work refer annexure a attached with this bsr 11 25 mm x 12 mm 12 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 13 2 x 2.5 sq. mm. + 1x1.5sqmm 14 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 15 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 16 3.0 mm thick 17 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 18 single pole mcb ( with b / c curve tripping characteristics ) 19 6 a to 32 a rating 20 double pole mcb ( with b / c curve tripping characteristics ) 21 40 a rating 22 four pole mcb ( with b / c curve tripping characteristics ) 23 50 / 63 a rating 24 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 25 metal door ( single phase ) ik 09 and ip 43 with metal end box 26 4 way ( 4+2 ) 27 p & f isi marked ( is:3854 ) 6 amp. flush type non modular switchwith cm / l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 28 p & f isi marked ( is :3854 ) 16 amp. flush type non modular switch cm / l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 29 providing & fixing ofof 3 / 5 pin 6 amp. flush typenon modular socketmade out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 30 providing & fixing of3 / 6 pin 16 amp flush type non modular socketmade out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 31 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 32 4 pole mccb with thermal magnetic release 33 160 amp , 25 ka, adjustable o / l & adjustable s / c setting, 34 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 35 10.0 sq. mm 36 2 core 37 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 38 up to 457 mm size 39 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 40 300 mm sweep ( 900 / 1400 rpm ) 41 380 mm sweep ( 900 / 1400 rpm ) 42 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 43 up to 380 mm size 44 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminiumhousing with in built driver, system lumen efficacy = 110 lm / watt output, internal surge protection of 2.5 kv with short & open circuit protection , thd < 10% , p. f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 45 1170mm ( + / 10% ) led batten with min. lumen output 2200 lm 46 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 47 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 48 recessed mounting 49 minimum lumen output 1300 lm 50 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 51 1200 mm sweep bee 1 star rated ( service value >=4.0 to < 4.5 ) 52 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 600 mm sweep wall mountingwith minimum air delivery 270 cum. / minute...

Public Works Department - Rajasthan

36407422 tender for electrical work in govt. janana hospital jhalawar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) on surface isi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface moulded virgin materialupvcmodular box , 10 a modular switch, modular faceplate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required. for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 2 short point ( up to 3 mtr. ) 3 medium point ( up to 6 mtr. ) 4 long point ( up to 10 mtr. ) 5 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) of approved make on surfaceisi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface 2 no. moulded virgin materialupvcmodular box , 2 nos 10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 6 medium point ( up to 6 mtr. ) 7 long point ( up to 10 mtr.. ) 8 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) on surfaceisi marked ( is:14927 p ii ) virgin materialupvc trunking & its accessories, hot dipped galvanizedmodular box of 1.2 mm thickwith earth terminal / surface moulded virgin materialupvcmodular box, modular 10a switch, 3 / 5 pin6 amodular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 9 on board 10 s&f following sizesof isi marked ( is:14927 p ii ) virgin materialupvc trunking along with accessorieslike coupler, inner, outer, elbow, square box, tee, end cap etc. on surfacewithscrews, expansionfastenersas required. for additional technical parameters of product / work refer annexure a attached with this bsr 11 25 mm x 12 mm 12 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 13 2 x 2.5 sq. mm. + 1x1.5sqmm 14 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 15 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 16 3.0 mm thick 17 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 18 single pole mcb ( with b / c curve tripping characteristics ) 19 6 a to 32 a rating 20 double pole mcb ( with b / c curve tripping characteristics ) 21 40 a rating 22 four pole mcb ( with b / c curve tripping characteristics ) 23 50 / 63 a rating 24 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 25 metal door ( single phase ) ik 09 and ip 43 with metal end box 26 4 way ( 4+2 ) 27 p & f isi marked ( is:3854 ) 6 amp. flush type non modular switchwith cm / l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 28 p & f isi marked ( is :3854 ) 16 amp. flush type non modular switch cm / l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including cutting hole in tile and making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 29 providing & fixing ofof 3 / 5 pin 6 amp. flush typenon modular socketmade out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 30 providing & fixing of3 / 6 pin 16 amp flush type non modular socketmade out from industrial grade polycarbonate or fire resistant abs material, brass terminal with porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 31 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 32 4 pole mccb with thermal magnetic release 33 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 34 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 35 10.0 sq. mm 36 2 core 37 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 38 up to 457 mm size 39 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 40 300 mm sweep ( 900 / 1400 rpm ) 41 380 mm sweep ( 900 / 1400 rpm ) 42 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 43 up to 380 mm size 44 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminiumhousing with in built driver, system lumen efficacy = 110 lm / watt output, internal surge protection of 2.5 kv with short & open circuit protection , thd < 10% , p. f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 45 1170mm ( + / 10% ) led batten with min. lumen output 2200 lm 46 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 47 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 48 recessed mounting 49 minimum lumen output 1300 lm 50 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 51 1200 mm sweep bee 1 star rated ( service value >=4.0 to < 4.5 ) 52 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 600 mm sweep wall mountingwith minimum air delivery 270 cum. / minute...

Department Of Atomic Energy - Rajasthan

36307568 bids are invited for wrought aluminium and aluminium alloys sheet and strip (general engineering purposes) is:737 (q3) mse total quantity : 70...

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

36306257 supply of vocational lab equipment trade health care ambu mask ( adult ) 1600ml. self­inflating double ended silicone bag with mounts incorporating reservoir valve and side feed oxygen inlet. 2 aed trainer with adult pad vermed physio­control multifunctiondefibrillator 3 stop watch royals digital stopwatch timer 4 oxygen cylinder portable oxygen cylinder ( 10 l, 150 breaths ) 5 oxygen key for in gas cylinder 6 oxygen cylinder trolley suitable for 20 litre size gas cylinder 7 hospital bed single function bed in which head end of the patient can be raised with a handle length: at least 2000 mm , breadth at least 900mm & height at least 500 mm 8 bedside locker • 760mm l x 360mm w x 750 mm h • square & rectangular tube frame • ss top • trolley mounted on 50 mmdia wheels• pre­treated& powder coated made of square / rectangular tube frameas well as stainless steel top and trolley mounted famish on 50 mmdia wheels isi / ce certification 9 cardiac table ­ over bed table ( cardiac table ) table top height adjustable • frame: tubular mild steel. • finishing: epoxy powdercoated, chrome plated adjustable 10 mattress ­ alternating pressure mattress system with adjustable pump the otica alternating pressure mattress was designed specifically to provide relief from bed sores and ulcers caused from prolonged bedrest. 11 bed sheet, pillow, pillow cover­ made from cotton. size approx. : 145 x225 cm. 12 blanket ­ pure woollen hosiery blanket single bed 13 wheel chair ­ nylon upholstery • full­length arms padded • carry straps on seat allow for ease of folding and lifting • footrest • fold ­down back• light weight 14 walker ­ standard oem product 15 crutch ­ standard oem product 16 table ( 3 ft by 6 ft ) ­ made of wooden 17 cupboard ­ steel cupboard for storage 18 stretcher ­ should be light, safe and reliable, made of aluminium 1alloy and hold for the same, easy to lock and unlock featuresproduct dimensions: 192 x 43 x 8cm net weight: 9kg stretcher bearing: 120kg 19 cane ­ 360 degree anti­slip pivoting base provides easy walk on all terrain. the support weight is up to 100 kg, 5 levels adjustable height from 34 inch to 39 inch in 1 inch increment.this walking stick provides additional support for people with arthritic / painful hands when walking indoors and outdoors. 20 back rest ­ • angle adjustable • foldable for easy storage 21 foot rest ­ overall approx. step size: 505l x 305w x 230h mm. 800 • frame made of 1 x 18g crc tubes fitted with pvc stumps. • pre­treated& epoxy powder coated. 22 steel basin ( large ) ­ stainless steel kitchen sink ( 16 x 18 x 8 inches, silver ) 23 bed pan ­ standard product 24 urinal ( male ) ­ standard product 25 urinal ( female ) ­ standard product 26 air cushion ­ standard oem product 27 sand bag ­ standard oem product 28 weighing machine ­ standard oem with isi / ce certification 29 steel tray ( large ) ­ standard product 30 steel tray ( medium ) ­ standard product 31 artery forcep ­ standard product rust free 32 dissecting forcep ­ standard product rust free 33 scissor ­ standard product rust free 34 nail cutter & filer ­ standard product rust free 35 splint ( large ) ­ malleable splints, made of aluminium alloy, can bestrapped, x ray compatible, easy to fix 36 splint ( medium ) ­malleable splints, made of aluminium alloy, can bestrapped, x ray compatible, easy to fix 37 splint ( small ) ­ malleable splints, made of aluminium alloy, can bestrapped, x ray compatible, easy to fix 38 cervical collar ( large ) ­ standard oem with isi / ce certification 39 cervical collar ( medium ) ­ standard oem with isi / ce certification 40 cervical collar ( small ) ­ standard oem with isi / ce certification 41 spine board ­ standard product •tapering from approx. 18 to 14 from head end to foot end. 74.2 long x 3.2 high at height of concave patient surface. • internal padding ­ non­absorbent, contoured, bevelled edges, adhesive backed, easy for sanitizing and re­applying. 65 x 11.375 x6mm. 42 steel plate ­ standard product rust free 43 steel glass ­ standard product rust free 44 steel bowl ­ standard product rust free 45 spoon ­ standard product rust free 46 steel jug ­ standard product rust free 47 bath tub ­ standard product 48 kidney tray ­ standard product large & small 49 iv stand ­ • 22 diameter chrome plated heavy bar steel base • lock to ensure secured height positioning • two­hook rams horn with secure­ grip tips • based on a four leg stand • height adjustment from 51 1 / 2 to 93 • bottom pole diameter is 1, upper pole diameter is 0.75 50 measuring glass ­ standard product non breakable 51 measuring tape ­ standard product 52 goggles ­ standard product 53 suction apparatus ­ a / c power with collection capacity of 200 ml with 20 litres per minute flow rate. backup for 20 min. provision with manualoperation in case of any power failure 54 syringe destroyer ­ standard oem with isi / ce certification electronicwith cutter. 55 syringesteriliser ­ standard oem with isi / ce certification electronicwith cutter. 56 needle burner ­ standard oem with isi / ce certification electronic withcutter. 57 thermometer ­ standard oem with isi / ce certification electronic withcutter. 58 syringe 50 cc / ml ­ standard oem with isi / ce certification electronicwith cutter. 59 b.p. monitoring machine ­ standard oem with isi / ce certificationelectronic with cutter. 60 hot water bottle ­ as per standard 61 ice caps ­ as per standard 62 transfer forceps ­ as per standard 63 drum ­ as per standard 64 dressing kit ­ as per standard 65 dressing scissor ­ as per standard 66 folley catheter ­ as per standard 67 euro bags ­ standard oem with isi / ce certification 68 ryle’s tube ­ as per standard 69 vaccutanour ( red / black / violet ) ­ as per standard 70 tourniquet ­ as per standard 71 examination table ­ as per standard 72 call bell ­ as per standard 73 rubber sheet / mackintonossh ­ as per standard 74 draw sheet ­ as per standard 75 bandage ­ as per standard 76 suction catheater ­ as per standard 77 bulb syringe ­ as per standard 78 oxygen mask ­ face mask with 2 m long star multi channel tube, size 79 stethoscope ­double sided aluminium chest piece with matt anodising. it is precisely machined for enhanced performance & durability. it features dual tunable diaphragms with brass chrome plated rings. the larger diaphragm is used for adult patients whereas the smaller diaphragm is used for paediatric patients. 80 towel­ cotton 81 gown ­ different size 82 gloves ( disposable ) – packet ­ as per standard 83 gloves ( surgical ) – packet ­ as per standard 84 liquid soap bottle ­ as per standard 85 mask – packet ­ as per standard 86 shoe cover ­ packet ­ as per standard 87 hair cap ­ packet ­ as per standard 88 sponge cloth ­ as per standard 89 wet wipes ­ packet ­ as per standard 90 comb ­ as per standard 91 tooth brush ­ as per standard 92 toothpaste ­ as per standard 93 hair oil ­ as per standard 94 shampoo bottle ­ as per standard 95 bath soap ­ as per standard 96 talcum powder ­ as per standard 97 different colour plastic bags with dustbins ( red ) ­ as per standard 98 different colour plastic bags with dustbins ( blue ) ­ as per standard 99 different colour plastic bags with dustbins ( black ) ­ as per standard 100 different colour plastic bags with dustbins ( yellow ) ­ as per standard 101 uro bag ­ t tap type 2000 millilitre 102 sample collection bottle ­ as per standard 103 gauze piece ( 4x4 ) ­ as per standard 104 betadine solution bottle ­ germicide gargle 105 cotton rolls ­ as per standard 106 cotton absorbent ­ supper cotton 107 normal saline bottle ­ as per standard 108 micro pore ­ 9.14 meter ( length on a roll ) without dispenser surgicaltapes 109 spatula ­ to collect pep smear, cytology specimen. 110 hydrogen peroxide bottle ­ stabilized hydrogen peroxide 111 cleaning solution ( colin ) ­ as per standard 112 stationary set­ multi­functional multi toolkit for office works, stationary organizer | stapler, scissor, punch, ruler, sharpener, opener, remover, ring, clip holder ( all in one kit ) 113 paper ( ream of 500 ) ­ a4 size 114 extension cord ­ with 4 sockets 115 speaker­ as per standard 116 fire extinguisher ­ 2 kg 117 alcohol based hand sanitizer ­ herbal, alcohol 118 n­95 mask ­ capelo with exhalation valve 119 rubber gloves ­ latex ­ water proof ­ hand gloves ­ pairs 120 unbranded steel tool box ­ for basic tools 121 temperature gun ­ non­contact digital infrared thermometer 122 manikin ( male & female ) ­ standard oem with isi / ce certification 123 oximeter ­ finger tip pulse oximeter with spo2, perfusion index andpulse rate readings, oleds display...

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

36124027 supply of medical and surgical related items for cwsn students 1 braille kit 10 braille slate, stylus, english trainer plate, geometry set, taylors frame, type sets, abacus, instruction manuals 2 taking calculator 10 a talking calculator has a built in speech synthesize that reads aloud each number, symbol or operation key a user pressrs; it also vocalizes the answer to the problem. it is a large size calcuator which also has provision for attaching earphones 3 geomrtary kit (blind) 10 kit consistin of a scale aluminum frame compass protractor a circular disk ect. having tactile marking enabling a person with blindness to construct figures accurately. 4 hearing aid two pair 10 type: bte suitable for: mild to moderate maximum power output:135 db spl 5 smart cane 10 an electronic travel aid which fits on top fold of the white cane. enhances white canes capability by detecting objects from knee to head height in front of a person. inbuilt rechargeable battery with 10 hours back up. 6 low vision devices 10 magnifier lenses, gogalss 7 mr kit 10 infinite loop stepping stones massage ball olive massage ball squeezer air cushion 8 daisy player 10 8gb flash storage and also support up to additional 32gb sdhc card high quality speakers guarantees louder and clearer voice; support daisy format : daisy 2.02, daisy 3.0 page 24 of 26 9 chess board for blind 10 brand generic material wood, plastic genre chess number of players 2 item dimensions lxwxh 34.8 x 22.1 x 3.8 centimeters 10 speech trainer (digital) 10 high sound quality with full acoustic energy output. portable lcd screen for navigation digital speech trainer output by headphone and inbuilt speaker visual, audio and tactile modality 11 oto scope 10 special feature battery required, led flash light power and plug description battery powered light source type led material abs included components mini portable fiber optical pen 12 tongue pressure 10 13 group hearing aid 10 headphone output (students unit) headphone impedance operating power (230 v ac) dimensions/weight teachers unit 14 walker 10 walker height can be adjusted from 62 cm to 70 cm from the ground to the walker hand grips. sturdy aluminum frame, high grade rubber shoe and rubber foam grip ensures maximum strength while remaining lightweight. it comes with rotating wheels for easy movements 15 wheel chair 10 type manual wheelchair seat type solid seat wheel type cast plastic wheel tyre type pneumatic arm design type full length arms backrest type fixed wheel lock type lever weight carrying capacity 100 kg foldable seat yes page 25 of 26 16 c.p. walker 10 type – c.p walker for kids square adjustable ring to hold the child in an upright position adjustable square ring 14” x 14” square ring adjustable height 22” to 30” overall length 24” overall width 22” overall height 32” wheel type 4 caster wheel of 2” frame 22 mm circular pipe of 18 gauge 17 c.p. chair 10 material: aluminium alloy overall height: 86 111 cm weight: 3.5 5 kg 18 white cane (foldable) 10 colour: white, black top bottom material: industrial grade aluminum elastic: double elastic with 3mm pure white for greater strength. unique joint design: connecting bushes for smooth functioning, great stability, and toughness foldable: yes, folding with 5 segments powder coating: high quality, fine surface finish size: 1150 mm length, 12.7mm diameter weight: 170g included components: whitecane 19 taking dictionary 10 talking dictionary software is a enabled english dictinary and thesaurus.like all tha talking software product talking dictionary has been disigned for use by the non sighted person.all of the controls are easily rememberd keyboard shortcuts and it is a very fast and easy programeto use .talking dictionary is designed to be usesd as a stand alone programe. what this means is that you do not need any kind of skreen reading softwarw or any thing else to use this programe 20 refreshable braille display 10 the braille me is a new smart braille display by innovision tech. this refreshable braille display is a 6 dot, 20 cell display with a perkins style keyboard that can be paired with ios and android devices, and has a micro usb, sd card slot and dc jack. this lightweight (1.3 lbs) device is compatible with voiceover, brailleback and nvda screen readers and supports 50+ languages. page 26 of 26 21 digital protbale audio meter ...

Department Of Defence - Rajasthan

35981320 bids are invited for miscellaneous items fan hook 5 inch , pvc pipe inch dia 10 feet long , pvc pipe 15 mm dia 10 feet long , pvc bend inch dia , pvc bend 1 inch dia , insulation tape 30 mtr x20 mm , balli hard wood size 3 inch to 6 inch dia 10 feet long , aluminium alloy straight 06 steps ladder, load cap 150 kgs , aluminium alloy straight 08 steps ladder, load cap 150 kgs , 04 step heavy duty foldable aluminium ladder , helmet grease gun 10 kgs cap , hyd jack 10 20 ton cap , battery charger 72 v , hand operating rotary pump for lifting of pol , measuring cane 10 ltrs cap , measuring cane 05 ltrs cap , ms pipe 1.5 inch dia 2 mm wall thick , ms sheet size 6 feet x 4 feet x 1 mm , ms wire 6 mm dia , sealing wire 0.8 mm dia , round lead seal 12 mm dia , lead sealing plier engraved with 1071 mark , dewatering pump set 05 hp with deisel engine drive, npsh 06 meter, suction and delivery in mm80 x 65, rpm 1500, total head 18 meter , microtek line interactive ups 1000 va with avr with 02 year warranty total quantity : 2018...

Military Engineer Services - Rajasthan

35865736 tender for repair and maintenance of misc b / r and e / m nature work in area under age ( i ) pokaran taking down carefully by unscrewing from boards / outlet boxes, switches, bell push, socket outlets, fan regulators, buzzers, holder and taken as schedule of credit. 2 disconnecting and removingthe mcbs, mccbs, dbs, metal clad switch from any height , stripping out the fitting for examine replacement of unserviceable spare parts, reassembling, refixing in original position includingminor repairs for the smooth functioning and testing complete all as specified & directed by engg in charge 3 m&l for attending, repair and rectification ofany type of internal elect supply complaint viz light point / fan point / 5 / 15 amps switch socket / submain wiring / mcbs / dbs / no electric supply on 230v / 415v system along with necessary t&p, safety devices, without replacement of items as per site requirement and as directed by engr in charge.note :1.the contractor shall detail / depute his supvr / electrician to receive the complaints from the concerned complaint cell and rectify the same on the given day alongwith necessary manpower and t & p as required.after completion of the complaints attended, the docket / slips shall be handed over to the concerned complaint cell.2. the cost of the stationery such as complaint register and docket book shall be deemed to be included in the rate quoted. 4 s & fswitch piano single pole flush type 5 amps, 230 volts. 5 s & fswitch piano single pole flush type 15 amps, 230 volts. 6 s & f single pole modular switch 1 way 6 amps, 1 module 7 s & fsingle pole modular switch 1 way 16 amps, 1 module 8 s&fbell push 5 a flush type 9 s&f modular bell push 6a, 1 module 10 supply and fixsocket outlet modular type multipurpose 2 / 3 pin, 6 amps, 230 volts combined 2 module 11 supply and fixsocket outlet modular type multipurpose 3 / 5 pin, 6 / 16 amps, 230 volts combined 2 module 12 supply and fixsocket outlet flush type multipurpose 2 in 1, 3 pin, 5 amps, 230 volts all as specified 13 supply and fixsocket outlet flush type multipurpose 2 in 1, 3 pin, 5 / 15 amps, 230 volts all as specified 14 s & fswitch socket combination flush type multipurpose 2 / 3 pin 5 amps 2 in 1230 volts all as specified. 15 s & fswitch socket combination 5 in 1 multipurpose 3 / 5 pin 5 / 15 amps flush typewith complete all as specified. 16 s & fmodular ceiling fan regulator stepped socket size ( modular ) suitable to work on 230 volts complete all as specified, 2 module 17 s & felectronic type regulator single module stepped heavy duty for ceiling fan suitable to work on 230 volts complete all as specified. 18 s & f electronic type regulator two module stepped heavy duty for ceiling fan suitable to work on 230 volts complete all as specified. 19 s&fbell ( buzzer / ding dong ) working on 230 volts ac supply 20 s & f lamp holder insulated body surface bakelite with back plate suitable for angle / batten fittings 21 s & fwall mounted 2 ft led batten of 9 watt with led lamp, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver complete including taking down all as specified and directed by engg in charge. make : havells cat part no luminebs9wled865spcwh / bajaj cat part no. bclsb10nw or equivalent. 22 s & f 4 ft box type tube light fitting with led tube rod of 18 / 22 watt , extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver complete including taking down all as specified and directed by engg in charge . make : havellscat part no regalbatten8upto1x22wssbswh and crystal1213t8dstl20wled865sglass / luker cat part no.llts1 or equivalent 23 supply and fix 4ft led tube rods of 18 / 20 / 22 watt complete including taking down all as specified and directed by engg in charge make: havells cat part no. crystal1213t8dstl20wled865sglass / bajaj cat part no.18wcdl orequivalent 24 s & f security lights of 1x25 watt led light with high power led and unique peanut lens to ensure uniform distribution and including provision of 1.5 sqmm 3 core multistranded copper conductor cable from light fitting to junction box complete all including taking down as specified and directed by engg in charge.make : havells cat part no endura pearl sl25wled757sasytopcmp / luker cat part no lst24 or equivalent 25 m & l bracket made out of gi pipe of suitable dia not less than 1.2 mtr long and fixed on walls with 2 nos ms clamps made out of ms flat of suitable size thick complete with ms nuts, bolts and washers etc bent to required shape complete including taking down all as specified and directed by engr in charge 26 s & f 15 watt recess mounted circular downlight with white powder coated polycarbonate housing and pressure diacast , heat sink having high efficiency and including taking down all as specified and directed by engr in charge make : havells cat part no enduraneodlr15wled840mod and analogdrivernm12 / 15w / crompton cat part no.scr 15w cdl orequivalent 27 s & f 15 watt surface mounted circular downlight with white powder coated polycarbonate housing and pressure diacast , heat sink having high efficiency and all including taking down as specified and directed by engr in charge. make : havells cat part no enduraneohesurfacedls15wled840s / crompton cat part no. lcdspln r 12 ww or equivalent 28 s & f 24 watt recess softline luminaire ( 1x1 ) suitable for armstrong / grid ceiling with high brightnesswhite leds and pmma extruded diffuser giving glare free light and good aesthetic appeal and all including taking down as directed by engg in charge. make : havells cat part no pluto 1x1 plr15wled857s / crompton cat part no. ccr 141 24 57 sl nwh or equivalent 29 all as per sl item no 49. here in before, but 2x2 fittings of 45 wattsincluding taking down all as specified and directed by engr in charge. make : havells cat part no venus neo he 2x2plr42wled857mod , leddriver63v1a42ws / crompton cat part no.ccr 126 50 40 sl nwh or equivalent 30 s & f 10 watt bulk head luminaire suitable for outdoor with high brightness giving glare free light and including taking down all as directed by engg in charge. make :havels cat part no. hexaft10wled857ssymbopc / bajaj bibwp10wled or equivalent 31 s & f mcb sp 6 to 32 amps 240 volts for fixing on mcb dbsall as specified. 32 s & f mcb sp40 to 63 amps 240 volts for fixing on mcb dbsall as specified 33 s & f mcb spn 16 to 32 amps 240 volts for fixing on mcb dbsall as specified 34 s & f mcb spn 40 to 63 amps 240 volts for fixing on mcb dbsall as specified 35 mcb four pole, 415 volts suitable for fixing in mcb db of capacity63 amps including removing the existing us one and making good the distrubed surface to match with the existing surface. 36 mcb four pole, 415 volts suitable for fixing in mcb db of capacity100 amps including removing the existing us one and making good the distrubed surface to match with the existing surface. 37 s & f sheet metal enclosure mcb dbspn 4 way with 200 amps rated bus bar 240 volts double door with locking system complete all as specified 38 all as per sl item no 37 here in before, but spn 8 way db 39 all as per sl item no 37 here in before but spn 12 way db 40 s & f horizontal type tpn db 4 way double door made out of crca sheet housing duly powder coated & confirming to is specification complete all as directed by engr in charge. 41 s & f vertical loadline type tpn db 4 way double door with incoming as mccb tp 415 volts ac 3 phase50 hz with fixed magnetic setting for current rating of 100 amps 16 ka ( mccb tp confirming to is specification made out of crca sheet housing duly powder coated & confirming to is specification complete all as directed by engr in charge. 42 s & f single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole mcb 20 amps ( ac box ) all as specified and directed 43 s&f mccbs 415v, 25ka, 100 amps 4 pole suitable for db including removing the existing unserviceable one and making good the distrubed surface to match with the existing surface. 44 all as per sl item no 43 here in before, but 63 amps, 10 ka 45 m & l submain wiring with 2 runs of single core 4 sqmm pvc insulated frls multistranded 1100 volts grade wire, copper conductor drawn through and including non metalic rigid pvc conduit and conduit accessories of medium grade not not less than 25mm dia including one run of single core 4 sqmm pvc insulatedsheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from db to db / main board including removing the existing unserviceable submain riwing complete all as specified and as directed. 46 all as per sl item no 45, but 2 runs of single core 6 sqmm and one run of single core 6 sqmm as earth continuty conductornote :for sl item no 66 to 67: two runs of cable, one run of earth wire and one run of pvc conduit will be measured as one unit 47 supply and fix 36 watt cfl 4 pin typecomplete all as specified and directed by engg in charge. 48 supply and fix 18 watt cfl 2 pin typecomplete all as specified and directed by engg in charge. 49 supply and replace electronic driver fordownlight of any capacity / watt as per site required all as specified and directed by engineer in charge. 50 supply and replace electronic driver for led light of2x2 fittingof any capacity / watt as per site required all as specified and directed by engineer in charge. 51 supply and replace bi pin holdersuitable for 40 / 28 watts tubes ( pin & screw type ) 52 supply and replace cfl holdersuitable for 2 / 4 pin for 9 to 36 watts 40 / 28 watts tubes ( pin & screw type ) 53 supply and replace fan condenser 2.5 mfd 54 supply and replace fan condenser of 4.00 mfd 55 supply and replace split pins / lock pins for ceiling fans 56 supply and replace ms clamp with rubber bushes, bolts & nuts for ceiling fan along with lock pin all as specified 57 m & l for repairs to copper inner container like denting, soldering, brazing, leak testing and reassembling of any ltrs capacity water heater ( geyser ) complete all as specified. 58 supply and replace geyser element2000 watts of any type or as per site requirement 59 supply and replace thermostat 60 supply and replace indicator bulb 230 v suitable for any make and colour. 61 supply and replace pvc cold / hot water connection pipe 45 cms long 15 mm dia 62 m & l rewinding of burnt ceiling fan of1200 / 1400mm sweep motor with supper enameled copper wire of suitable size including repainting it white , replacement of sealed bearing and shaft of any make, type, model incl transportationcomplete all as specified and directed by engineer in charge. 63 m & l rewinding of burnt exhaust fan of 225 / 300mm sweep motor with supper enameled copper wire of suitable size including repaintingas per site requirement, replacement of sealed bearing and shaft of any make, type, model incl transportationcomplete all as specified and directed by engineer in charge. 64 s&f ceiling fan downrod of required heightincluding drilling of holes and threads for the same as per the site requirement all as direted by engineer in charge. 65 s & f ceiling rose three terminal surface bakelite type ac 50 hz 230 volts of size 65 x 50 mm complete all as specified. 66 supply and replace pvc round blocks 67 supply and replace pvc dummy sheets circular type of 4 68 supply and replace pvc dummy sheets circular type of 6 69 supply and replace rigid pvc casing & capping 20 / 25 mm wide 70 supply and replace pvc rectangular box ( gang box ) with 5 amps switch socket 71 supply and replace pvc rectangular box ( gang box ) with 5 / 15 amps switch socket 72 supply and replace pvc wire of flexible cord with copper conductor multistanded of twin core 23 / 0.198sqmm 73 supply and replace pvc insulated frls copper wire of size 1.5 sq mm multistranded 1100 volts grade 74 supply and replace pvc insulated frls copper wire of size 2.5 sq mm multistranded 1100 volts grade 75 supply and replace pvc insulated frls copper wire of size 4.0 sq mm multistranded 1100 volts grade 76 supply and replace pvc insulated frls copper wire of size 6.0 sq mm multistranded 1100 volts grade 77 supply and replace service wire twin core of 10.0 sq mm multistranded 1100 grade 78 supply and replace plug top 5 amps 3 pin 250 volts 79 supply and replace plug top 15 amps 3 pin 250 volts 80 supply and fix white hylam plain laminate sheet ofthickness as per the site requirement and as directed by engr in charge. 81 repair / maintenance of 25 ltrs ro plant of any make by removing of all electrical connections and water connections, rectification of all electric complaints including replacement of wiring and cleaning of all filters all as specified by engr in charge 82 s&f filters of 25 ltrs ro plant all as specified and directed 83 taking down chowkats or frames with shutters ( w / o taking of shutters from the frame ) exc. 1.5 sqm but n.exc. 4 sqm & removing from site. 84 taking down chowkats or frames with shutters ( w / o taking of shutters from the frame ) area n. exc 1.5 sqm removing from site 85 taking down shutter of any description and removing frome siteexc. 1 sqm & n. exc. 2 sqm each leaf. 86 taking down shutter of any description and removing frome siten exc. 1 sqmeach leaf. 87 m&l for joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. ( cut to ordinary lengths i.e. within 20mm of the length indicated ) fe 410 w ( gde e 250 ) quality a 88 s&f 35mm thick plain framed, panelled shutter ( two panel ) with lock rail and panel of 9 mm b.w.p commercial ply or 12 mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per is: 1003 ( part i ) , kiln seasoned and chemically pressure treated 89 supply and fix flush shutter solid core construction with block board core and plywood face panels commercial typeboth side, 30mm thick. 90 s / f 2nd class h.w. skeleton shutter 35 mm thick open rebated & prepared to receive glass, gauze, etc. divided into squares with plain chamfered or rounded & rebated sash bars ( of any nos ) as spd in ssr pt i sec 8 cl. 8.20. ( a ) . 91 s&f solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s square tube, supplying & fixing in opening as per specification & drawing 92 s&f factory made solid panel pace door shutter 30mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails, m.s. frame shall be covered with heat moulded plain colour pvc `c channel heaving a pvc sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s frame wedded / sealed to the stiles, & rails with suitable pvc sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing. 93 steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded 94 steel ventilator with top hung shutter including hinges, steel peg stay, complete 95 s&f 4 mm thick sheetglass ordinary quality and glazingwith oilputty in squaren exc 0.50 sqn in each pane. 96 s&f 4 mm thick figured glass, pin headed type and glazingwith oilputty in squaren exc 0.50 sqn in each pane. 97 resecuring or easing & adjusting, taking down shutters of any description n exc 1 sqm each refixing in same opening 98 resecuring or easing & adjusting, taking down shutters of any description exc 1 sqmn exc 2 sqm each, refixing in same opening 99 s&f 100 mm long mild steel but hinges medium weight cold rolled. 100 s&f in repairs 100 mm long mild steel but hinges medium weight colld rolld. 101 s&f 150 mm long aluminium anodised barrel tower bolt of extruded section. 102 s&f in repairs150 mm long aluminium anodised barrel tower bolt of extruded section . 103 supply and fix 150mm long extruded aluminium alloy handles, 150mm long fabricated type., anodised 104 supply and fix in repairs extruded aluminium alloy handles, 150mm long fabricated type., anodised 105 s&f 300 mm long aluminium alloy anodised sliding door bolt with hasp staple ( bolt type ) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast alu allow. 106 s&f in repairs 300 mm long aluminium allow anodised sliding door bolt with hasp staple ( bolt type ) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast alu allow. 107 s&f stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples 108 supply & fix in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples 109 supply and fix in repairs floor door stopper of aluminium body and tongue anodised with hard drawn steel spring fixed in floor over all length of cover plate 150mm. 110 supply and fix repairs decorative type curtain rod , stainless steel, 25 mm dia with not less than 1mm wall thickness complete all as specified and directed. 111 supply and fix decorative type brackets , stainless steel, suitable for above curtain rod complete all as specified and directed. 112 hacking out old broken glass ( any thickness, size, quality or description ) frommetal frame including punching or drilling out old glazing pins / spring clips and providing and fixing new ones 113 s&f 3 mm thick sheet glass ordinary quality & glazing with oil putty in squares n. exc. 0.5 sqm in each pane. 114 s&ffigured glass 3 mm thick, pin head type & glazing with oil putty in squares n. exc. 0.5 sqm in each pane 115 prelaminated particle board, interior grade, prelaminated both side 18 / 19 mm thick with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work but prelaminated both sides with decorative choice laminations 116 s&f continuous ( piano ) hinges, mild steel, bright finish or electro galvanizedwidth of flaps ( when open ) 30 mm. 117 m&l iind class hard wood plain fillets, square, rectangular or triangular in section, clean swan, se cured with nails or brads, sectional area not exc 3.00 sqcm. 118 s & f aluminium anodised hasp and staple 75mm , safety type, mild steel hinge pin including bolt to hinge plate and fixed with screws 119 s&f 100 mm long aluminium anodised barrel tower bolt of extruded section . 120 supply and fix extruded aluminium alloy handles, 100 mm long fabricated type., anodised 121 s&f, anodised aluminium frame & shutter for door, window and ventilator including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, hinges, tower bolt, etc complete all as specified & directed by engineer in charge. 122 supply only 5.5 mm thick sheet glass, selected quality, in square exc 0.5 sqm each pane including solar control film 25 micron reflective type over it. 123 supply only 5.5 mm thick sheet glass, selected quality, in square nexc 0.5 sqm each pane including solar control film 25 micron reflective type over it. 124 s&f door closer ( aluminium extuded body section ) hydreulically regulated, , designation no 1 universal type, suitable for door shutters up to 700mm in width and of wieght not more than 35kg complete all as directed. 125 s&fmild steel 4 lever mortice lock, vertical type of size 100mm all as directed. 126 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises 127 m&l for colored non skid ceramic tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colored cement to match, including 15 mm thick screed bed or bedded layer in cement mortar 1:6 for laying floor finish. 128 m&l for colored glazed ceramic tiles ( 300mm x450mm ) x 7 mm thick on vertical surfaces set and jointed in neat cement slurry and pointed in white or colored cement to match including 10 mm thick plaster in cement mortar ( 1:4 ) on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing to receive / fixing dado / skirting tile. 129 dismantling of stone slab in any description or thickness, laid bedded jointed in any morter. 130 material and labour for granite ( of any type ) 18 to 20 mm thick work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match withshadeincl 15mm thick screed bed in cm 1:6 complete. 131 drilling holes for bolts, pipes, etc. n. exc 25mm dia in granite or trape stonefor gas connection pipe 132 rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations 133 s&f vitreous china coloured wash hand basin 580mm x 450mmfixed in repairs including 15 mm pillar cock cast copper alloy cp, 15mm cast copper stop valve, 32 mm brass cp waste fitting & 15 mm pvc connection pipe 450 mm long fixed in repairs 134 s&f vitreous china wash down water closet coloured pan ( pedestal pattern ) , white ( excluding fixing bolt, flushing cistern and flush pipe ) complete connected to drain fixed in repair 135 supply and fix in repairs vitreous china squatting pan, ‘orissa’ pattern, size 580 x 440 mm white, with integral foot rests ( excluding flushing cistern and flush pipe ) 136 s&f in repairs plastic water closet seat cover black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminum hinging device 137 s&f pvc flushing cistern 10 ltrs capacity isi marked incl pvc down take pipe and connection etc all complete in repairs. 138 supply and fix in repairs vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white ( minimum ) , with grating and union ( exclusive of fixing supply pipe to flushing cistern, trap and waste pipe ) fixed in repair 139 s&f for stop cock copper alloy cp screwed down high pressure with crutch or butterfly handle screwed both ends for iron / pipe or for union and fixed 15 mm bore in repairs 140 s&f bib taps cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs 141 s&f in repairs cp health faucet spray with 1.5m long pipe with wall hook& fixed in repair complete 142 supply and fix in repairs bib taps two way type , cast copper alloy with crutch or butterfly handle, sc rewed down, screwed for iron pipe or for brass ferrule 15 mm boreand fixed 143 s&f in repairs 32mm dia pvc waste pipeforkitchen sink , whb , urinal etc 144 supply and fix 15mm bore pillar taps of cast copper with capstan head cp screwed down high pressure with or without lettered hot and cold with long screwed shank and fly nut for iron pipe and fixed in repairs 145 s&f in repair brass cp mixer for mixing hot & cold water screwed down for iron pipe and fixed 146 s&f pvc connections 15 mm size with ptmt nuts to length 450 mm in repairs. 147 s&f , brass, chromium plated, tubular towel rail, 20mm dia, d type, 60cm long between flanges 148 s&f in repairs soap dish, any type, fixed to plugs with chromium plated brass screws 149 supply and fix in repairs brass chromium plated shower roses 125mm sizewith or without swivel joints, any size, including fixing to steel pipe or union 150 s / f s s grating dome of 100 mm dia ( min wt 25 gms ) to floor traps in repairs. 151 s & f 600mmx450mm beveled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers 152 taking down steel tubing and connections including cleaning for re fixing or removal to store of 15 mm bore 153 taking down steel tubing necessary fittings connection etc for 20 mm bore pipe 154 cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth 155 s&f gi tubes of medium grade with all fitting and fixed complete to walls and ceilings or laid in floors of 15 mm dia 156 s&f tubes medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floors 20 mm dia 157 supply and fix pvc ( swr ) floor trap, plain with grating including jointing with solvent cement 75 mm dia out let 158 s&f in repair pvc ( swr ) pipes single socketed in any length with rubber ring joints fixed to walls 110 mm dia 159 s&f in repair pvc ( swr ) pipes single socketed in any length with rubber ring joints fixed to walls 75 mm dia 160 supply and fix in repairs ball valves high pressure of ptmt with epoxy coated aluminium rod and highdensity plastic ball screwed for iron pipe and fixed in repairs of pipe 15 mm dia. 161 supply and fix in repairs ball valves high pressure of ptmt with epoxy coated aluminium rod and highdensity plastic ball screwed for iron pipe and fixed in repairs of pipe 20 mm dia. 162 supply and fix in repairs 15 mm dia bib tap standard of ptmt any colour high pressure screwed for iron pipe and fixed . ( minimum weight 15mm 90gms / 20mm 125gms ) 163 supply and fix in repairs 15 mm dia pillar taps of ptmt any colour high pressure screwed for iron pipe and fixed ( minimum weight 15mm 110gms ) ) 164 supply and fix in repairs 15 mm dia stop valve of ptmt any colour high pressure screwed for iron pipe and fixed ( minimum weight 15mm 90gms / 20mm 112gms ) 165 s&f in repairs sinks made of stainless steel of 1 mm thick kitchen sink with plug washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495 x 420 mm bowl size 410 mm x 330 mmx 160 mm 166 s&f in repair sinks made of stainless steel 1mm thick in kitchen sink with plug washers and waste pipe including bedding in cement mortar to dwaft wall or incl fixing cantilever brackets and connecting unionto pipe over all size 915 x 460 mm bowl size 410mm x 330 mm x 160mm all as specified and directed. 167 dismantling water tanks & removing from site, capacity of tanks exc 250 litres & n. exc. 500 litres capacity each 168 dismantling water tanks & removing from site, capacity of tanks 500 ltr and n exc 1000 ltr 169 s&f rotational moulded polyethelene water storage tanks ( cylindrical, vertical with closed top ) hoisted & fixed in position all as specified in ssr pt i, 500litre capacity. 170 s&f rotational moulded polyethelene water storage tanks ( cylindrical, vertical with closed top ) hoisted & fixed in position all as specified in ssr pt i, exc 1000 ltr capacity...

Indian Army - Rajasthan

35791200 bids are invited for 1 g1 5305 002681 screw wood slotted csk head mild steel n 2 g1 5305 002673 screws wood slotted countersunk head mil 3 g1 5325 000169 eyelet aluminium alloy no.28 4 g1 5305 002699 screw wood slotted csk head mild steel n 5 g1 5305 002713 screw wood slotted csk head mild steel n 6 g1 5305 002686 screw wood slotted csk head mild steel n 7 g1 5305 002700 screw wood slotted csk head mild steel n total quantity : 25391...

Department Of Defence - Rajasthan

35763764 bids are invited for misc items fan hook 5 inch , pvc pipe inch dia 10 feet long , pvc pipe 15 mm dia 10 feet long , pvc bend inch dia , pvc bend 1 inch dia , insulation tape 30 mtr x20 mm , balli hard wood size 3 inch to 6 inch dia 10 feet long , aluminium alloy straight 06 steps ladder, load cap 150 kgs , aluminium alloy straight 08 steps ladder, load cap 150 kgs , 04 step heavy duty foldable aluminium ladder , helmet grease gun 10 kgs cap , hyd jack 10 20 ton cap , battery charger 72 v , hand operating rotary pump for lifting of pol , measuring cane 10 ltrs cap , measuring cane 05 ltrs cap , ms pipe 1.5 inch dia 2 mm wall thick , ms sheet size 6 feet x 4 feet x 1 mm , ms wire 6 mm dia , sealing wire 0.8 mm dia , round lead seal 12 mm dia , lead sealing plier engraved with 1071 mark , dewatering pump set 05 hp with deisel engine drive, npsh 06 meter, suction and delivery in mm 80 x 65, rpm 1500, total head 18 meter , microtek line interactive ups 1000 va with avr with 02 year warranty total quantity : 2018...

Military Engineer Services - Rajasthan

35657758 tender for addn or altn to building no p 137 at af stn mount abu s&f solid pvc wall lining consisting of 5mm thick wood grain printed pvc sheet inclusive of solvent cement and fixing at site on pvc frame as per specifications and drawing all as directed by engr in charge. 2 s&f 5mm thick pvc sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make pvc frame as per specification and drawing. 3 dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings 4 m&l for galvanised corrugated mild steel sheeting of thickness 0.63 mm with two corrugations side lap, fixed with coach screws and washers in roofs walls etc with grade of zinc coating 275 fixed with l type or j type or cranked hook bolts in lieu of screws 5 m&l for plain galvanised mild steel sheeting of thickness 0.63 mm as in ridges , valley gutterswith grade of zinc coating 275 6 s&f joist channel angle, tee section, ms pipe, ms square tube , steel trusses as required , ms plate fixed in purlin rafter cleat, support and including cutting of grooves in stone masonry and ms frame work fixed into the walls etc incl welding, riveting, j hook etc conf to fe 290 gde e 165 all as directed by engr in charge 7 m&l preparation of new steel surfaces over 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide. 8 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises 9 m&l for 600mmx600mmx10 mm thick vetrified light shade ceramic tiles shade as approved flooring ( in any pattern ) andjointed with neat cement slurry over 15 mm thickcement screed in cm 1:6 and pointed with coloured cement matching with surfaces of tiles as in floor complete all as specified and directed. 10 excavation in trenches in hard rocks not exc 1.5m in width and not exc 1.5 in depth for foundation and getting out. 11 m&l cement concrete type d21:4:8 ( 40 mm graded aggregate ) as in foundation, filling and mass concrete. 12 m&l brick work with sub class b bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. 13 m&l for 15 mm thick rendering on fair faces of brickwork or concrete surfaces in cm 1:4 surface finished even and smooth without using extra cement with water proofing compound complete all as specified and directed.. 14 m&l for returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm 15 removing excavated materialsto a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point rocks 16 taking down chowkhats or frames with shutter ( without taking off shutter from the frame ) exc 1.50 & n.exc. 4 sqm in each complete all as specified & directed. 17 s&f solid pvc double door frame of size solid pvc double door frame of size 50mm x 95mm made out of 5mm plain colour pvc sheet reinforced with m.s. tube, suppling & fixing in opening as per specified and directed. 18 s&f factory made solid pvc moulded door shutter with particle board core, 28 to 30mm thick ( stiles ) , with 2, 4, or 6 raised panel design with 2mm thick moulded pvc sheet on the front face & 2mm plain colour pvc sheet on back face, supplying & fixing in frame at site as per specified and directed. 19 s&f aluminium alloy anodised sliding door bolt with hasp & staple ( bolt type ) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm. 20 s&f 150 mm long aluminium, anodised, barrel tower bolts of extruded section 21 s&f 150 mm size, aluminium handles, cast type, anodised. 22 s & f 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised. 23 m&l for preparing of old surfaces of any description and applyingtwo coats of plastic emulsion exterior paint inover a coat of primer complete all as specified & directerd. 24 cleaning of roof slab / chajja with sweeping with brooms, removing all depositions / mud / vegetations etc complete all as specified and directed by engineer in charge. 25 m&l for preparing new surfaces of roof and applying two coat of dr. fixit roof seal top coat ( classic ) or equivalent and a coat of dr. fixit roof seal top coat ( diluted with water in the ratio 2:1 ) as self priming seal acrylic coating as per manufacturer’s instruction to stop leakage / seepage from roof ( gi sheet ) / wall butbefore primer, all the bolt joints are to be filled with dr. fixit feviseal hy 100or equivalentand the leakage is to be sealed ( rate include in this item ) complete all as specified and directed by engineer in charge.note: 1. two coat of roof seal top coat ( classic ) @ 2.0 2.2 sqm / ltr / coat, without water dilution at rate of application being the same for both coats. this would ensure correct consumption of material to deliver a total 450 500 micron thickness and a coat of self priming @ 9 10 sqm / ltr.2. quoted rate shall be deemed to be included for work in buildings / structure of any height. 26 m&l 75 mm thickpcc1:4:8typed 2 ( using 40mm grade stone aggregate ) asinsub floors, sub bases , flooring etc 27 m&l chequered pvc moulded cement concrete tilesdark shade 30 cm x 30 cm x 22 mm thick set , jointed and pointed in neat cement slurryin floorswith gray cement and pigment with screed bed 15 mm cm 1:6 complete all as specified by engr in charge 28 taking down copper / aluminium point wiring ( light, fan, socket or power ) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit ( credit for above items should be made as per conditions separately ) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed by engineer in charge. 29 point wiring complete concealed type incl cutting chases in stone wall for conduits and sinkings for boxes and making good to walls, floors etc with 1.5 sqmm single core multi standard copper conductor pvc ( frlsh ) insulated sheathed cable in and incl pvc conduit heavy duty ( wall fitness not less than 1.8 mm ) with accessories existing pressed steel terminal boxes ( sunk in wall ) including new 3.00 mm thick plastic laminated sheet top cover with 1.50 sqmm pvc insulated unsheathed copper conductor frls for common earth and connecting to earth dolly for: ( a ) one light point / exhaust fan / ceiling controlled by one switch one way & ceiling fan with one way switch & regulator. 30 ( b ) one socket out let 5 amps 5 pin on same board with other switch complete all as specified and directed by engineer in charge. 31 ( c ) one switch socket combined5 amps 5 pin on independent board complete all as specified and directed by engineer in charge. 32 all as per item no 5 here in before but with frlsh multistranded cable of size 4 sqmm and multistanded insulated copper earth continuity conductor of size 4 sq mm complete all as specified and directed by engineer in charge. for: ( a ) one switchsocket combination outlet 16 amp power point on independent board. 33 s&fceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified and directed by engineer in charge. 34 s&fmodular switch 6 amp 250 v ac one way one module complete all as specified and directed by engineer in charge. 35 s&f modular switch socket combined, 6a 2 / 3 pin combined 2 module complete all as specified and directed by engineer in charge. 36 s&f modular switch socket 6a / 16a 2 / 3 pin combined 2 module complete all as specified and directed by engineer in charge. 37 s&f aesthetically designed ledpanel for surface mounting which provides soft light and glare free symmetrical illumination 34 watt, of size 2 x 2 led light fitting, including twin core flexible copper cable for connection of the lights and connectors where required complete all as specified and directed by engineer in charge.make havells cat part no:plano2x2plr34wled865s 38 m&l for dismantling of ac of capacity 1.5 / 2.0 ton split typecomplete all as specified and directed by engineer in charge. 39 m&l for fixing of ac 1.5 / 2.0 ton split type with all connection in the original conditioncomplete all as specified and directed by engineer in charge....

Military Engineer Services - Rajasthan

35594842 tender for welcome maintenance at jalipa mil stn under ge army barmer taking down cement plaster of any description, on brick or stone walls etc.including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. ( note : work will be done / executed in patches without damaging other undamaged portion, of any size as directed ) 2 m&l for rendering 10mm thick plaster in cm ( 1:6 ) on faces of brick work or concrete surfaces, finished even and smooth ( without using extra lime or cement ) complete all as specified and directed. 3 m&l for rendering 5mm thick plaster in cm ( 1:3 ) on faces of brick work or concrete on surfaces of ceiling, finished even and smooth without using extra cement complete all as specified and directed. 4 m&l for rendering 15mm ( in two layers 10mm+5mm ) thick plaster in cm ( 1:4 ) on faces of brickwork or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. 5 m&l for preparing new plastered or unplastered surfaces of walls and applying two coats of oil emulsion distempering over a coat of interior wall primer complete all as specified and directed. 6 m&l for preparing new plastered or unplastered surfaces of walls and applying three coats of white wash complete all as specified and directed. 7 m&l for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. 8 m&l for 3mm thick wall care putty on wall complete all as specified and directed. 9 m&l for preparation of new plastered surfaces of walls and applying two coat of cement based paint over a coat of primer complete all as specified and directed. 10 hacking out old broken glass ( any thickness, size, quality or description ) from from metal frame including punching or drilling out old glazing pins / spring clips, glazed with putty or fixed with beads and providing and fixing new ones complete all as specified and directed. 11 m&l for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square in n exc 0.5 sq.m in each pane complete all as specified and directed. 12 m&l for 3mm thick figured glass, pin head type and glazing with oil putty in squares in n exc 0.5 sq.m in each pane complete all as specified and directed. 13 m&l for preparing old plastered or unplastered surfaces of walls including filling of cracks / holes by crack filler, removing unnecessary nails and applying one coat of white wash complete all as specified and directed. 14 m&l for preparing old plastered or unplastered surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails and applying two coats of white wash complete all as specified and directed. 15 m&l for complete removal of existing treatment, plastered or unplastered old surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails and applying three coats of white wash complete all as specified and directed. 16 m&l for preparing old plastered or unplastered surfaces of ceiling, including filling of cracks / holes by crack filler, removing unnecessary nails and applying one coat of white wash complete all as specified and directed. 17 m&l for preparing old plastered or unplastered surfaces of ceiling, including filling of cracks / holes by crack filler, removing unnecessary nails and applying two coat of white wash complete all as specified and directed. 18 m&l for complete removal of existing treatment, plastered or unplastered old surfaces of ceiling, including filling of cracks / holes by crack filler, removing unnecessary nails and applying three coats of white wash complete all as specified and directed. 19 m&l for preparing old plastered or unplastered surfaces of walls including filling of cracks / holes by crack filler, removing unnecessary nails and applying one coat of oil bound distemper / emulsion complete all as specified and directed. 20 m&l for preparing old plastered or unplastered surfaces of walls including filling of cracks / holes by crack filler, removing unnecessary nails and applying two coats of oil bound distemper / emulsion complete all as specified and directed. 21 m&l for complete removal of existing treatment, plastered or unplastered old surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails applying two coats of oil bound distemper / emulsionover a coat of interior wall primer over 3mm thick wall care putty complete all as specified and directed. 22 m&l for preparing old plastered or unplastered surfaces of walls including filling of cracks / holes by crack filler, removing unnecessary nails and applying one coat of cement based paint complete all as specified and directed. 23 m&l for preparing old plastered or unplastered surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails and applying two coats cement based paint complete all as specified and directed. 24 m&l for preparation of old painted wood and wood based surfaces of any description over 10cm in girth or width and painting with one coat of synthetic enamel paint complete all as specified and directed. 25 m&l for preparation of old painted wood and wood based surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paint complete all as specified and directed. 26 m&l for preparation of old painted steel or iron surfaces of any description over 10cm in girth or width and painting with one coat of synthetic enamel paintcomplete all as specified and directed. 27 m&l for preparation of old painted steel or iron surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paintcomplete all as specified and directed. 28 demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed. 29 m&l for granite ( of any type ) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting andpolishing types including 15mm thick screed bed in cm ( 1:6 ) , complete all as specified and directed. 30 m&l for glazed ceramic tilesof size350mm x 250mm x 7mm / 450mm x 350mm x 7mm thick ( coloured ) of superior qualityfixed on vertical surfaces such asskirting / dado etc, set and jointed in neat cement slurry over 10mm thick backing coat in cm ( 1:4 ) and pointed in coloured cement to match complete all as specified and directed. 31 m&l for non skidceramic tiles of size 7 to 8mm thick ( coloured ) ( square / rectangular ) area of each tile exc 0.06 but n exc 0.11 sqm, in floors, set & jointed in neatcement slurry and pointed in coloured cement over 15mm thick screed bed in cm ( 1:6 ) complete all as specified and directed. 32 taking up or down 15mm bore steel water tubing & connections from walls / ceilings / floors including cleaning for refixing or removal to store all as specified and directed. 33 taking up or down 20mm bore steel water tubing & connections from walls / ceilings / floors including cleaning for refixing or removal to store all as specified and directed. 34 s&f for 16mm bore of cpvc of food grade pipes sdr 11 and plain cpvc sdr 11 fittings on walls / ceiling or laying in floors complete all as specified and directed. 35 s&f for 20mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed. 36 cutting chases in brick walls, stone, concrete block or slab walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth all as specified and directed. 37 s&f in repair 150 mm long aluminium anodizes barrel tower bolts of extruded section complete all as specified and directed. 38 s&f in repair 150mm size aluminium anodized handle complete all as specified and directed. 39 s&f in repair 250mm long aluminium alloy anodized sliding door bolts with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. 40 s&f in repair mild steel ordinary rat tail rod pattern spring 300mm size including roller & roller plate and incl welding complete all as specified and directed. 41 s&f in repair 100mm size mortise lock, aluminium, vertical type, four leavers, all as specified and directed. 42 s&f in repair pvc cabinet 450x600mm overall size with looking mirror of selected qality 5mm thick glass mounted over pvc framing as per sample complete all as specified. ( make : neelkamal / prayag ) 43 s&f in repair 450mmx600mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. 44 s&f for brass knobs 35 40mm dia complete all as specified and directed. 45 s&f ball catches with 8mm dia steel ball, and brass body and striking plate 140mm length including letting in and fixed complete all as specified and directed. 46 s&f in repair aluminium floor door stoppers double legged length 140mm with hard drawn steel spring fitted in floor complete all as specified and directed. 47 dismantling of boarding any description fixed in any position with nails complete all as specified and directed. 48 m&l for prelaminated particle board of 18 / 19mm thick, interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination with teak wood leaping on exterior face, fixed with screws as in cupboard shutters of bed room, kitchen andinternal shelves complete all as specified and directed. 49 s&f width of flaps ( when open ) in 40 mm continuous ( piano ) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed. 50 s&f for 75mm size ms butt hinges cold rolled medium weight complete all as specified and directed. 51 s&f in repair stainless steel wire cloth 0.36mm nominal dia of wire andaverage width of aperture 1.40mm and fixed with stainless steel wire stapples of any type of windows and doors i.e. wooden, steel or aluminium including opening and refixing of frame, shutter or shutter elements if required and new wooden beads in wooden doors, complete all as specified and directed. 52 s&f in repair 20mm dia stainless steel curtain rod with fancy type fixing brackets, stops, rollers etc. complete all as specified and directed. 53 s&f in repairs mild steel window handles of approved quality with fixing nuts complete all as specified and directed. 54 s&f in repairs ms peg stay for steel window 300mm long with nuts complete all as specified and directed. 55 s&f in repair 15mm bore bib taps cp fancy type, cast copper, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 56 s&f in repair 15mm bore dia pipe cp wall mixer for mixing ( hot / cold ) water, with wall cap / band of cp brass, screwed down, screwd foriron pipes 15mm bore complete all as specified and directed. 57 s&f in repair 15mm bore brass cp sink mixer fancy type with swinging casted spout ( wall mounted type ) for kitchen sink screwed down for iron pipe and fixed complete all as specified and directed. 58 s&f in repair 15mm bore centre hole basin mixer fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `hot and `cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed. 59 s&f in repair 15mm bore cp fancy type stop valves / angle cock, cast copper alloy, screwed both ends for iron pipe or for union complete all as specified and directed. 60 s&f in repair 15mm bore two way bib taps ( for health faucet / jet spray ) fancy type, chromium plated, cast copper ally with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 61 s&f in repair 32mm dia pvc waste pipe for whb / sink complete all as specified and directed. 62 s&f in repair 15mm bore, 450mm long, pvc connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and directed. 63 s&f in repair vitreous china wash down water closet pan ( pedestal pattern ) , white including p or s trap, connection to drain ( or outgoing pipe ) and to flushing pipe with and including plastic water closet seat, white closed pattern with flat bottom, cover and mild steel hinges device complete all as specified and directed. 64 s&f in rep vitreous china squatting pan “orissa” pattern, of size 580mm x 440mm white with integral foot rests and trap ( excluding flushing cistern and flush pipe ) including trap and provn of cement concrete bedding complete as fixed complete all as specified and directed. 65 s&f in repairs wash hand basins, vitreous china, of size 550x400mm ( flat back, or angle back type ) including cutting for and pinning in ends of brackets or erecting standinclusive of fixing of supply and waste pipe etc complete all as specified and directed. 66 s&f in repair plastic water closet seat for pedestal / semi pedestal closet pan, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified. 67 s&f in repair pvc valveless flushing cistern, low level white with inlet ball valve float and handle including brackets complete fixed capacity of flush 10 ltrs complete all as specified and directed. 68 s&f in repair brass chromium plated shower rose 125mm size complete all as specified and directed. 69 s&f in repair health faucet ( abs body ) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and abs wall hook including making connections and fixed in position complete in all respect complete all as specified and directed. 70 s&f in repair ss soap dish, approximate size 150x 150x80mm, fixed to plugs with chromium plated brass screws complete all as specified and directed. 71 s&f in repair toilet paper holder with flat recessed type stainless steel fixed to walls with chromium plated ( cp ) brass screws complete all as specified and directed. 72 s&f in repair sheet glass corner wall mounted shelf assembly consisting of 8mm thick sheet glass 220mmx220mm size with chromium plated bracket guard and railing 50mm high complete all as specified and directed. 73 s&f in repair brass chromium plated tubular towel rail 20mm dia, d type, 60cm long between flanges complete all as specified and directed. 74 s&f in repair jet spray ( abs body ) mild steel chromium plated suitable for 15mm dia pipe with 1.00 metre long flexible tube including making connections and fixed in position complete in all respect complete all as specified and directed. 75 s&faluminium window / ventilator frame with side hung shutters ( fully glazed ) and aluminium grill 7.50mm thick as per design code no. 007 of dural grill or equivalent make as approved comprising of chokhat and shutters weight not less than 0.55kg / rm including jointing cleat, aluminium snap beading 20x15mm, rubber gasket, glazing clip, sheet glass 3.00mm thick selected quality for panels and aluminium hardware fitting fixed with steel chromium plated screws such as 02nos, 100mm size aluminium d type handles, 02 nos 75mm size stainless steel medium weight hinges, 02nos 100mm long aluminium tower bolts, one peg stay 150 mm long etc including taking down complete all as specified and directed . 76 s&f powder coated aluminium door frame with side hung shutters ( fully glazed ) comprising of chokhats section 101.04 x 44.45 x 1.5mm thick, shutter top rail 86.17 x 44.45 x 2.3mm, bottom and lock rail 150 x 44.45 x 2.3mm and style 53.7 x 44.45 x 2.3mm and including jointing cleat, aluminium snap beading 20 x 15mm, rubber gasket, glazing clip, sheet glass 5.5mm thick figured / solar control film glass selected quality for panels and aluminium hardware fitting fixed with steel chromium plated screws such as 02 nos disc type round handles, 03 nos 100mm size hinges, 03 nos 150mm long tower bolts, one floor door stopper with hard drawn steel spring 140mm long, 01 number of double action floor spring hydraulically regulated made upto minimum 1.25mm thick aluminium alloy sheet junction box for each leaf main body with stainless steel sheet cover governing pivot of brass, other parts made of mild steel heavy duty etcincluding taking down complete complete all as specified and directed. 77 s&f aluminium door frame with side hung shutters ( fully glazed ) comprising of chokhats section 101.04 x 44.45 x 1.5mm thick, shutter top rail 86.17 x 44.45 x 2.3mm, bottom and lock rail 150 x 44.45 x 2.3mm and style 53.7 x 44.45 x 2.3mm and including jointing cleat, aluminium snap beading 20 x 15mm, rubber gasket, glazing clip, sheet glass 5.5mm thick figured / solar control film glass selected quality for panels and aluminium hardware fitting fixed with steel chromium plated screws such as 02 nos disc type round handles, 03 nos 100mm size hinges, 03 nos 150mm long tower bolts, one floor door stopper with hard drawn steel spring 140mm long, 01 number of double action floor spring hydraulically regulated made upto minimum 1.25mm thick aluminium alloy sheet junction box for each leaf main body with stainless steel sheet cover governing pivot of brass, other parts made of mild steel heavy duty etc including taking down complete all as specified and directed. 78 m&l for prepration of surface by cleaning to remove loose particles, dust, latance etc, cutting grooves again remove loose particles, dust, latance etc properly, filling cracks / damaged portions / hollow areas / gaps of rcc and masonary upto 10mm to 15mm widhth and 10mm to 20mm deep by using polymer modified cement mortars and making good surface like existing painted surface with the help of cement mortar and paint all directed and as per manufacturers instructions. make : m / s asian paint / berger / m / s pidilite industries ltd / stp ltd / choksey. 79 m&l for prepration of preparation of new / old decorated plastered or unplastered surfaces of walls / chajjas by cleaning to remove loose particles, dust, latance etc., filling of holes / cracks with cns filler material. applying one priming coat ofsmart care damp proof with thinner at the rate of 0.40 ltr / sqm ( 0.20ltr smart damp proof : 0.20ltr water ) . applying second coat ofsmart care damp proof after 05 to 06 hrs at the rate of 0.40 ltr / sqm, and apply the third coat after 6 to 8 hrs once the second coat is dry at the rate of 0.40 ltr / sqm all directed and as per manufacturers instructions. make : m / s asian paint / berger / pidilite industries ltd / stp ltd. / choksey. note : cracks filler, priming coat and damp proofing coat shall be used of same make / manufacturer. 80 taking down copper / aluminium point wiring ( light, fan, socket or power ) complete including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing unserviceable materials for taking credit ( credit for above items should be made as per conditions separately ) and making good disturbed surfaces of walls, floors etc complete all as specified and directed. 81 taking down unserviceable main switch / db, teak wood boards etc complete all as specified and directed 82 taking down old unserviceable sub main wiring and making good the disturbed surfaces complete all as specified and directed. 83 m&l for point wiring surface type with single core 1.5 sqmm pvc insulated unsheathed single core multistranded copper conductor cable ( frls ) including 1.5 sqmm pvc insulated unsheathedcopper conductor as earth continuity conductor drawn in and including isi marked pvc casing caping not less than 20mm width with its accessories, including necessary modular metal flush box / pressed steelterminal boxes and modular white cover plate / 3 mm thick isi marked laminated sheet cover and ss screws with cup washers for fixing switches, sockets, fan regulators etc. including making good disturbed surfaces if any with cement mortar 1:3 for fixing switches / sockets / regulators etc. for one light point controlled by one switch complete all as specified and directed. 84 all as per srl item no 83 above but for call bell point controlled by one switch. 85 all as per srl item no 83 above but for one light point controlled by two 2 way switches. 86 all as per srl item no 83 above but for one fan point controlled by one switch. 87 all as per srl item no 83 above but for one 3 pin 5 amps socket outlet point on independent board. 88 all as per srl item no 83 above but for one 3 pin 5 amps socket point on the same board with other switches. 89 all as per srl item no 83 above but with cable 2.5 sqmm including 2.5 sqmm cable as earth wire for 15 / 16 amp socket. 90 all as per srl item no 83 above but with cable 4 sqmm including 4 sqmm cable as earth wire for 15 / 16 amp socket. 91 m & l switch piano, flush type single pole, one way 5 amps complete all as specified and directed. 92 m&l socket outlet 2in1, 3pin, 5a complete all as specified and directed. 93 m&l switch socket combination 2 in 1, 3 pin, 5 amps and 15 amps flush type universal complete all as specified and directed. 94 m&l ceiling rose surface bakelite 65x50 mm two to three terminals complete all as specified and directed. 95 supply and fix steped type electronic fan regulator flush type, 230 volt, ac complete all as specified and directed. 96 m&l bell push, flush type, 5 amps complete all as specified and directed. 97 m&l call bell ac, 230 volts single pole complete all as specified and directed. 98 supply and fixing 06 to 32 a rating 240v, 10 ka c curve miniature circuit breaker ( mcb ) of single pole and current carrying capacity in the mcb db complete with connection testing and commissioning complete all as specified and directed. 99 all as per srl item no 98 above but spn 6 32 amps. 100 supply and fixing 415v 10ka c curve miniature circuit breaker ( mcb ) of tripple pole and neutral ( tpn ) and current carrying capacity 40 to 100 a in the db complete with connection testing and commissioning complete all as specified and directed. 101 supply and fix single pole and neutral enclosures with a two pin and earth plug and socket complete with one double pole mcb 20 a, 240 v complete all as specified and directed. 102 s&f mcb, db double door type, made out of crca mild steel sheet flushed in wall, spn 8 way , 240 volts ip 43, with pvc mcb blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of mcbs and isolators etc including complete all as specified and directed. 103 s&f mcb, db double door type, made out of crca mild steel sheet flushed in wall, tpn 4 way with 200 amps rated bus bar , 415 volts ip 43, withpvc mcb blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of mcbs and isolators etc includingcomplete all as specified and directed. 104 m&l sub main wiring surface type with two runs of single core, pvc insulated, unsheathed multi standard copper conductor cable of size 4 sqmm, 1100 volts grade ( frls ) and one run of 4 sqmm pvc insulated multi stranded copper conductor for earth continuityconductor drawn through and including suitable size isi marked rigid pvc conduit with all necessary accessories such as bends, tees, junction boxes, elbowscomplete all as specified and directed. ( note : two runs of 4 sqmm cable, one run of 4 sqmm continuity earth wire and one run of pvc conduit with all necessary accessories will be measured as one length ) . 105 m&l sub main wiring surface type with two runs of single core, pvc insulated, unsheathed multi standard copper conductor cable of size 6 sqmm, 1100 volts grade ( frls ) and one run of 6 sqmm pvc insulated multi stranded copper conductor for earth continuityconductor drawn through and including suitable size isi marked rigid pvc conduit with all necessary accessories such as bends, tees, junction boxes, elbowscomplete all as specified and directed. ( note : two runs of 6 sqmm cable, one run of 6 sqmm continuity earth wire and one run of pvc conduit with all necessary accessories will be measured as one length ) . 106 supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 v, 1200 mm sweep, min air delivery 210 cfm with service value 6.00 bee. five star rated with brushless direct current motor ( bldc ) complete including connecting with 3 core flexible copper conductor including taking down the existing ceiling fan and depositing the same in mes store complete all as specified and directed. 107 supply and fix ceiling fans, complete with three blade, down rod, accessories 230v, 1200mm sweep, with squirrel cage induction motorcomplete including connecting with 3 core flexible copper conductor including taking down the existing ceiling fan and depositing the same in mes store complete all as specified and directed. 108 supply and fix exhaust fan, steel body ac single phase. 230v of size 300m sweep with, blades, and frame and louvers complete including connecting with 3 core flexible copper conductor including taking down the existing exhaust fan and depositing the same in mes store complete all as specified and directed. 109 supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230v, 50 hz, rpm 1200, copper winding of sweep 250mm complete including connecting with 3 core flexible copper conductor including taking down the existing exhaust fan and depositing the same in mes store complete all as specified and directed. 110 supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 kw capacity 25 litre, bee 5 star rated complete with all accessories such as safety valve, thermostate, nrv, connection piece etc. and fixing on wall with toggle bolts and connecting with pvc flexible pipe complete including taking down the existing storage water heater and depositing the same in mes store complete all as specified and directed. note: pvc connection pipe, ground toggle bolts for fixing water heater will be measured and paid separately under relevant items. 111 supply only ground toggle bolts ( tower / anchor ) , 6 long along with washers and nuts for fixing geysers 25 / 50 ltrs capacity. 112 supply only pvc connection 15 mm bore with ptmt nuts of length 600mm in repairs complete all as specified and directed. 113 supply only pvc metal braided connection pipes for hot water supply with brass adopters 600mm long. 114 supply and fix in repair led bldg security light fitting 25 watt 230 v ac outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65 / 66 protection complete all as specified and directed. 115 supply and fix in repair led lights fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed 116 supply and fix in repair led light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 117 s & f in repair led light fitting 1x9w / 1x10wbulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 118 supply and fix in repair lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. 119 taking out old u / s rubber reel of ceiling fan any make / size and supply and fixing heavy duty shackle type rubber reel complete with clamps. nut, bolt with split pin and washers complete all as specified and directed. 120 taking out defective capacitor and supply and fixing capacitor of rating 2.5 / 3.15 mfd230 vall as specified and directed. 121 supply & fix in repair fan regulator electronic step type 300 watt 240 volts including dismantling of old unserviceable regulator complete all as specified and directed. 122 supply and fix in repair modular switch 1 way 6 a, 1 module complete all as specified and directed. 123 supply and fixin repair modular switch 1 way 16 a, 1 module complete all as specified and directed. 124 supply and fixin repair modular bell push 6 a, 1 module complete all as specified and directed. 125 supply and fix in repairmodular socket, 6 a 2 / 3 pin combined 2 module complete all as specified and directed. 126 supply and fixin repair modular socket, 6a / 16a 2 / 3 pin combined 2 module complete all as specified and directed. 127 supply and fix in repair switch piano, flush type single pole, one way 5 amps complete all as specified and directed 128 supply and fix in repair switch socket outlet 2in1, 3pin, 5a complete all as specified and directed 129 supply and fixin repair switch socket combination 2 in 1, 3 pin, 5 amps and 15 amps flush type universal complete all as specified and directed 130 supply and fix in repair bell push, flush type, 5 amps complete all as specified and directed. 131 supply and fixin repair call bell ac, 230 volts single pole complete all as specified and directed 132 s&f in repair pvc board 30 x 25 x 5 cm depth medium quality isi marked complete all directed. for fixing of switches, sockets and regulators including taking down the old one complete all as specified and directed. 133 m & l for inverter point wiring forlight, ceiling fan and 5 amp socket with 2.5 sqmm, pvc insulated, unsheathed, single core multistandard copper conductor cable ( frls ) , 1100 volts grade including 2.5 sqmm pvc insulated, unsheathed, copper conductor cable for earth continuity wire to be drawn through in and including pvc conduit medium grade isi markedwith its acessories upto the main dband 15 a switch socket combination with gang box flushed in wallfor inverter power supply complete all as specified and directed....

Indian Army - Rajasthan

35581622 bids are invited for 1 g1 5305 002681 screw wood slotted csk head mild steel n 2 g1 5305 002673 screws wood slotted countersunk head mil 3 g1 5325 000169 eyelet aluminium alloy no.28 4 g1 5305 002699 screw wood slotted csk head mild steel n 5 g1 5305 002713 screw wood slotted csk head mild steel n 6 g1 5305 002686 screw wood slotted csk head mild steel n 7 g1 5305 002700 screw wood slotted csk head mild steel n total quantity : 25391...

Rajasthan Rajya Vidyut Utpadan Nigam Limited - Rajasthan

35524588 requirement of spares for 33kv double circuit line installed at different river water pump houses of ctpp, chhabra , 33kvsuspension type ( 4 bolt ) b & s type hardware 45 kn clamp 4 bolt type material hot dip galvanized aluminum alloy as per bs 729, bolts utype 16mm ( galvanized ) , cotter pin 16mm stainless steel , 33kv overhead steel core aluminum conductor ( acsr ) dog conductor, isi marked ( is 398 part ii 1996 ) number of strands and wire diameter in mm a. aluminium 6 / 4.72 ±0.05mm b. steel 7 / 1.57±0.03mm , special stud structure for 33kv lattice structure made of m.s. angle, channel, flats complete in all respects with bracings. ( structure must be paintedof approved make two coat of red oxide paint and two coat of aluminum paint completed ) 100x50mm channel, height 12.8m thickness not less than 6mm , gi stay set confirming to pattern 1 of bs: 16 / 1974 complete with stay rod including stay wire with anchor plate fitted with cast iron cross head and steel bow complete. required for 33kv lattice tower...

Rajasthan State Ganganagar Sugar Mills Limited - Rajasthan

35338085 construction of various civil work under package 1 at kaminpura sugar factory, sri ganganagar , construction of godown ( 30 x 20 ) feetfor winery in rsgsml campus kaminpura district sriganganagar , earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils , providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.a ) m10 grade nominal mix a ) m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size ) . , a ) m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size ) . , b ) m20 grade nominal mix: 1: 1.5: 3 ( 1 cement: 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size ) . , brick masonry with f.p.s. bricks of class designation 75 in foundation and plinth with bricks : cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) . , providing and laying in position specified grade of cement concrete for all rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix , centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. , providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircasesand spiral staircases etc. m20 grade nominal mix / design mix , centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. , brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in : cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) , providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor five level. ( original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to is:1786 ) : cold twisted deformed bars ( is : 1786 ) . , providing and fixing steel gate, grating, and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide , plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : , a ) 20mm thick. , b ) 12mm thick , painting with synthetic enamel paint of approved brand and manufacture to give an even shade: two or more coats on new work , wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding : two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. , painting exterior surface of wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision : new work. , supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. , providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section ( is 1038 1983 ) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 ( 1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size ) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooperglazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required : partly fixed and partly openable [ fixed area not to exceed 33% ] , supplying and fixing rolling shutters of approved make, made of 80 x 1.25mm. m.s. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 25.3cm. long wire springs grade no. 2 and m.s. top cover 1.25mm thick for rolling shutters as per design & is 6248 1979. ( clear openable area to be measured for payment ) . , steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m ) fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete : hot finished welded type tubes. , structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting ( height upto 10 m ) , fixing in position and applying a priming coat of approved steel primer all complete. , supply and installation of multi rib proofing / cladding sheet manufacture out of 0.60mm tct ( total coated thickness ) high tensile zinc aluminum alloy coated galvalume steel ( as per 150gsm zinc aluminum coated 550mpa tuekd strength ) confirming to is: 1397 / astm a 792 sheet to have wide pens 30mm high nb at 250 centre and centre width of 1020mm sheets be casted with regular modified polyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have proportionality with siphoned plate made to prevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. the sheet shall be supplied in cost one length and for a minimum up to 12mts with all scaffolding. , construction of shed ( jaggery production ) at rsgsm ltd kaminpura distt. sriganganagar , earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils , providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stoneaggregate 40mm nominal size ) . , brick masonry with f.p.s. bricks of class designation 75 infoundation and plinth with bricks cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) , providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix , centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. , providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor five level. ( original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to is:1786 ) thermo mechanically treated bars ( conforming of relevent is code ) , supplying and filling in plinth with blown sand under floors including watering ramming consolidating and dressing complete including cost of sand. , dry brick on edge flooring in required pattern with bricks of class designation 75 on a bed of 12 mm mud mortar including filling joints with river sandcomplete. , providing and laying m30 grade controlled cement concretepavements including mixing and vibrations concrete with necessary needle vibrators and surface with screed board vibrating complete in all respect with 20 / 25 mm stone aggregate ( crusher broken ) including anti skid textured finish to required camber / super elevation and grade including curing etc. as per specification with cement concrete m 30 grade including cost of steel frame work for sides of c.c. pavement consisting of m. s. channels flats and angles with required steel pegs ( some of them may left embedded in concrete / including providing frame work ) , structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting ( height upto 10 m ) , fixing in position and applying a priming coat of approved steel primer all complete: , supply and installation of multi rib proofing / cladding sheet manufacture out of0.50mm tct ( total coated thickness ) high tensile zinc aluminum alloy coated galvalume steel ( as per 150gsm zinc aluminum coated 550mpa tuekd strength ) confirming to is: 1397 / astm a 792 sheet to have wide pens 30mm high nb at 250 centre and centre width of 1020mm sheets be casted with regular modified polyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have proportionality with siphoned plate made to prevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. the sheet shall be supplied in cost one length and for a minimum up to 12mts with all scaffolding.add extra for 0.60mm tct ( total coated thickness ) high tensile zinc aluminum alloy coated galvalume steel sheet in place of 0.50mm thick 0.50mm thick , plaster on new surface on walls in cement sand mortar 1:4 including rackingofjointsetc. complete fine finish :20mm thick . , painting with synthetic enamel paint of approved brand and manufacture togive an even shade : two or more coats on new work , construction of rcc tank ( 17x 8 x 8 ) at rsgsm ltd kamanipura distt. sriganganagar , earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils , providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stoneaggregate 40mm nominal size ) . , providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix , centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. , providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor five level. ( original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to is:1786 ) thermo mechanically treated bars ( conforming of relevent is code ) , stone slab roofing on ground floor with fine grained stone slab from approved quarry including filling of joints of parapet and slab on both sides in cement sand mortar 1:4, with ceiling pointing in cement sand mortar 1 : 3 complete as per specification and instruction of engineer in charge , providing and laying brick kharanjaon roofs with cement mortar 1:4 ( 1 cement : 4 coarse sand ) mixed with 2% integral water proofing compound in square pattern 75mm to 100mm thick average , grading roof for water proofing treatment withwater proffing compoundcement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) ...

Rajasthan State Sports Council - Rajasthan

35208753 supply of sports equipment boq , shotput iron 3 kg turned & round shape with proper grip, as per internatinal norms & standards , discus 1kg fiber made, durable quality& proper grip, as per international norms&standards , javelin 500 gms made of aluminium alloy extra durability & stability, javelin head made of steel for extra durability, as per international norms&standards , shuttle cock feather duck / goose feather.16 to 18 feathers. fixed in base of cock with proper flight, as per inernatinal norms& starndards , badminton racket graphite frame with graphite shaft synthetic grip with proper gutting, as per international norms & standards , basketball net nylon made, white colour with 12 loops, as per international norms & standards , basketball rubber no 6 rubber material, circumference 29.5to 30 weight 20oz, as per international norms & standards , cricket bat k / w size no. 6 kashmir willow with cane handle, well balanced & striking power with fine grip , cricket ball tennis made of fine felt & proper bounce , football synthetic or p.u. material, standard size no, 5 with bladder, properly stiched circumference 68to cms, wight 410 to 450 gms, as international norms & standards , handball synthetic men size synthetic made, size no 3, circumference 56 58 cms, weight 425 to 475 gms, as per international norms & standards , handball net hdpe / polyproplene material with dori, as per international norms & standards , hocky stick wooden hocky stick made of cane material with p.u grip, with astro truff pattern balde shape, length 35 to 37.5 international norms & standards , hocky truf ball hocky ball, made of eva material, hollow inside pattern, dimple shaped for astro truff, dia of ball 2.8 to 2.96.weight 153 to 158gms, as per international norms & standards , lawn tennis ball made of fine felt, with proper pressure & bounce, size 2.57 to 2.70 in diameter, weight 1.98 oz to 2.10 oz., yellow colour packed in vaccum proof box, should be ideal for all courts, as per international norms & standards , lawn tennis racket made of 100% graphite meterial with p.u grip, as per international norms & standards , valleyball net twistered hdpe thread material, size 10mtr x 1mtr, non tearing vinyal all around tape, machine knitted, uv treated, mesh size10cms ( approx ) , pvc coated metal wire with rust proof eylets, as per international norms & standards , volleyball synthetic made of synthetic / p.u material, multi coloured, hand stitched with latex badder inside, diameter 65 to 67 cms, weight 260 to 280 gms, as per international norms & standards , skipping rope made of pvc rope with plastic handles, prferbly with ball bearings, length 9ft approx. , shooting ball as per international norms & standards...

Rajasthan Rajya Vidyut Utpadan Nigam Limited - Rajasthan

35128194 procurement of spares for 33kv double circuit line installed at different river water pump houses of ctpp, chhabra , 33kvsuspension type ( 4 bolt ) b & s type hardware 45 kn clamp 4 bolt type material hot dip galvanized aluminum alloy as per bs 729, bolts utype 16mm ( galvanized ) , cotter pin 16mm stainless steel , 33kv overhead steel core aluminum conductor ( acsr ) dog conductor, isi marked ( is 398 part ii 1996 ) number of strands and wire diameter in mm a. aluminium 6 / 4.72 ±0.05mm b. steel 7 / 1.57±0.03mm , special stud structure for 33kv lattice structure made of m.s. angle, channel, flats complete in all respects with bracings. ( structure must be paintedof approved make two coat of red oxide paint and two coat of aluminum paint completed ) 100x50mm channel, height 12.8m thickness not less than 6mm , gi stay set confirming to pattern 1 of bs: 16 / 1974 complete with stay rod including stay wire with anchor plate fitted with cast iron cross head and steel bow complete. required for 33kv lattice tower...

Department Of Atomic Energy - Rajasthan

34619285 bids are invited for wrought aluminium and aluminium alloys bars, rods and sections ( general engineering purposes ) is:733 ( q3 ) total quantity : 70...

Rajasthan Rajya Vidhyut Utpadan Nigam Limited - Rajasthan

34479050 requirement of fire fighting items for ssctpp, suratgarh , supply items , spindle ss 304 as per is :6603, for hydrant valve. , bonnet ss 304 as per is: 3444 gr. 1, for hydrant valve. , ss 304 lugs bush assembly for landing valve as per is: 6603, for hydrant valve. , hose couplingss 304 as per is:3444 gr.1 , for hydrant valve. , quartzoid bulb detector thread: 1/2, airproof test pressure 24 bars (2.4 mpa), temperature: 79 degree celsius, certification: 9001 2000 certified. it operates as a valve by allowing the flow of water contained in fire qbd system when the heat sensitive element (glass bulb or fusible link) is operated. , fire axe as per is: 926, made of forged steel, hardened, and having insulated, for fire service use. , fire bucket 9 litres capacity bucket as per is standard design as per is: 2545 made out of heavy duty g.i. , bonnet for hydrant valve base plate sheet (metallic) with base plate check nut as per is: 304 made of ss with neoprene rubber washer for spindle. , fire beater as per is: 8096, made of carbon (mild) steel mesh, and having bamboo handle, suitable for fire fighting class a , hand wheel material c.i is: 210 for hydrant valve. , suction hose 100 mm armored suction hose complete with round thread with gun metal couplings to suit the pump inlet 2.5 m long as per is: 2410 and is: 902. , suction strainer for 100 mm suction hose as per is: 907. , two way dividing breaching made of light alloy as per is: 5131. , hand controlled branch multi purposes branch (nozzle) the nozzle should be adjustable gallonage with multiple flow settings & 63 mm bim inlet hand nozzle. the nozzle should have selectable flow setting of 115 230 360 475 550 lpm @ 7 bar with flush mode without shut off the nozzle made of pyrolite material, with pistol grip made of zytel and with celcon ball valve. the nozzle shall have feature for straight stream & spray pattern. the length of branch should not exceed more than 10.5” and weight should not exceed more than 2.5kg. the branch should be simple to operate pattern control (1/4 turn from straight stream to fog). it should have minimum fog angle of 110° and raised lug marks straight stream for limited visibility operations. it should be capable of flushing without shutting down or changing stream patterns. the branch should be nfpa 1964 compliant, fm approved & ce certified. the warranty for branch should be minimum five years. , fire hook as per is:927. , 100 mm suction hose conforming to is: 241 in 4.5 m length with 100 mm suction hose coupling conforming to is: 902. , suction adaptors 100 mm female to 63 mm instantaneous male. , rubber washer for 63 mm couplings. , high range zero torque nozzle specifically designed with ergonomics, handling, control, and reduced firefighter fatigue in mind. in addition, the pistol grip and inlet swivel are positioned to eliminate the reaction force torque found in all conventional pistol grip designs. nozzle shall be combination of solid stream and fog nozzle with the capability to flow either stream independently or simultaneously. the solid bore shall have field changeable tips with orifices of either 3/8, ½, 5/8, ¾, 7/8, 15/16, 1, or 11/8 and the fog shall flow. the nozzle shall have spinning teeth, multiple pattern detents, flush without shutting down, twist shutoff of the fog stream, and a full time swivel inlet 2 ½”. the weight of nozzle not more than 4 kg. the bale shutoff of the smooth bore shall be with dual drive trunnions. the nozzle shall also be constructed of lightweight pyrolite, have a shutoff ball with flow diversion for the fog waterway, have a 05 year warranty and meet nfpa 1964. , jet spray shut off type fog nozzle120 conforming to is:952 , 63 mm male instantaneous inlet connection, gunmetal material with natural polished, operating pressure 10 kg/cm2 , jet fog typenozzle, conforming to bs: 336 , 63 mm male instantaneous inlet connection, aluminum alloy material with natural finish, operating pressure 10 kg/cm2 , revolving type branch pipeconforming to is:906 63 mm male instantaneous inlet connection, gunmetal material with natural polished, operating pressure 10 kg/cm2, flow 245 lpm @ 7 kg/cm2. , inline foam generator, inlet connection 63 mm male instantaneous as per bs 336/is: 903 , outletconnection 63 mm female instantaneous as per bs 336/is: 903, foam induction 3 t0 6 %, maximum working pressure 10 kg/cm2 , fb 5x pickup tube, operating pressure 5 to 5.5 bar. , fb 5x with pickup tube as per is: 2097 , jet length (maximum) 20 meter, 63 mm male instantaneous coupling , aluminum alloy, angle of operation 30 degree celsius. , seat washer material neoprene rubber is:937, for hydrant valve...

North Western Railway - Rajasthan

34320589 supply of bi metallic parallel clamp ( 15 / 20 ) made of aluminium alloy complete with fasteners confirming to rdso drawing no. eti / ohe / p / 1560 rev d or latest and rdso spec. no. ti / spc / ohe / fittings / 0130 ( 10 / 13 ) rev. 1 or latest.bi metallic parallel clamp ( 15 / 20 ) made of aluminium alloy complete with fasteners confirming to rdso drawing no. eti / ohe / p / 1560 rev d or latest and rdso spec. no. ti / spc / ohe / fittings / 0130 ( 10 / 13 ) rev. 1 or latest., bi metallic parallel clamp ( 15 / 20 ) made of aluminium alloy complete with fasteners confirming to rdso drawing no. eti / ohe / p / 1560 rev d or latest and rdso spec. no. ti / spc / ohe / fittings / 0130 ( 10 / 13 ) rev. 1 or latest....

Department Of Atomic Energy - Rajasthan

34136225 bids are invited for cast aluminium alloy cryogenic shell , sealing tape roll for cast aluminum alloy cryogenic cell and sealing tape roll pipe freezing purpose. total quantity : 21...

Military Engineer Services - Rajasthan

34098552 special repair to bldg no. t 39 and special repair to road furniture item at mil cantt ajmer under ge nasirabad. special repair to bldg no. t 39 and special repair to road furniture item taking down cement or cement lime plaster on stone / brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 2 m& l for 15 mm thickrendering in cement mortar ( 1:6 ) , on stone masonary surfaces finished even and smooth, complete all as specified and directed 3 m&l for rendering 15mm thick in cm 1:4 on stone masonry, external surfaces finished even and smooth, complete all as specified and directed 4 m & l forpreparation ofnew plastered surfaces of wallsand providing two coat of cement base paint over a coat of primer, complete all as specified and directed. 5 m & l forpreparation old decorated surfaces of wallsand providing one coat of cement base paint complete all as specified and directed. 6 m & l for complete removal of existing treatment andpreparationwall surfaces and applying two coats of oil bounddistemperover a coat of primer over 1 mm thick wall care of putty complete all as specified and directed 7 m&l for preparation of new plastered surfaces and applying two coats of oil bounddistemperover a coat of primer over 1 mm thick wall care of putty complete all as specified and directed. 8 m&l for preparation of old wooden surfaces of any descriptionover 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 9 m&l for preparation of old concretesurfaces of any descriptionover 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 10 s & f second class hw 35mm thick, factory made, plain framed, paneled shutter ( three panels ) with panels of 9mm thick bwpgrade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to is 710. the size of rails & style shall be as per is 1003 ( part i ) kiln seasoned & chemically pressure treated complete all as per specified and directed. 11 s&f 2nd class hw 35 mm thick, gauged and skeleton shutters ( three panels ) , factory made open rebated and prepare to receive glass, gauge etc ( with sash bar ) , edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. size of members of shutter shall be as specified in ssr 2009 part i, section 8 clausemember shall be kiln seasoned& chemically pressure treated complete all as specified and directed. 12 s&f steel window / ventilator glazed and gauged ( combination ) with side hung / top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete incl necessary ac / cooler arrangement in window & guard barscomplete all as as specified and directed. note : wire mesh and sheet glass shall be measured & paid separately under respective items. 13 s & f aluminium handle fabricatedtype, anodised 150mm size conforming to is complete all as specified and directed. 14 s & f 300mm long aluminium alloy, anodised, sliding door bolts with hasps, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all asspecified anddirected. 15 s&f aluminium, anodised, barrel tower bolt of extruded section, isi marked, 150 mm long complete all as specified and directed. 16 s&f mild steel butt hinges, medium weight, cold rolled, isi marked of size 100 mm, complete all as specified and directed. 17 m & l for rolled mild steel work angle ironas in door frame ( chowkhats ) of frame confirming to fe 290 or fe 330 including complete all as specified and directed. 18 taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) exc 1.50 sqm and n.exc 4.00 sqm each and removing from site complete and making good disturbed surfaces of wall in cm ( 1:3 ) all as specified and directed. 19 taking down unserviceable chowkhats or frame with shutters ( without taking off shuters from the frames ) of any description n exc 1.50sqm and removing from site and making good disturbed surfaces of wall in cm 1:3 complete all as specified & directed. 20 m & l for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of ist quality over a coat of pink primer complete all as specified and directed. 21 m&l for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed. 22 s&f stainless steel wire cloth 0.36mm nominal dia of wire & average width ofaperture 1.40mm & fixed with wire staples complete all as spd & directed. 23 s&f 3.00 mm thick sheet glass, ordinary quality & glazing with oil putty not exc0.50 sqm each pane complete all as spd & directed. 24 s&f in repair road stud ( cat eye ) abs bodyconforming to irc 67 1977giving reflection on both sides including fixing with epoxycomplete all as specified and directed. 25 s&f in repair solar road studs made up of highly compressive materials , water resistant alluminium alloy and polycarbonates 122 x 122x 20mm with 6 ledprismatic reflective lens on each side with stemfixed inroadcomplete all as specified and directed by engineer in charge. 26 m&l for 2 3 mm thick and 100 mm wide thermo plastic reflective painting white or golden yellow all as specified as on road surfaces in marking speed breakers, centre line, edge line etc complete all as specified and directed. 27 exavating in post holes ( or similar holes ) each n.exc 0.5 cum getting out in soft / lose soil returning, filling in and ramming earth in layers n.exc 25cm, watering and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specified and directed. 28 m&l for pcc 1:3:6 type c 2 using 40mm graded aggregate as in foundation filling and mass concrete complete all as specified and directed. 29 m&l for 1.65mm thick & 50 mm bore ( outer dia 60.3mm ) stainless steel pipe of schedule 5 s sign board complete all as specified and directed. 30 s&f informatory sign board in reqd size and each sign board made of two 4mm thick aluminium composite panel ( acp ) , both side face to fully covered with 3m scotchlite brand high intersity prismatic grade retro reflective sheet shall be astm d 4956 type iv in required colour.the retro reflective sheet shall be processed on acp by 3m equipment heat lamp vacum applicaror and letter, signs and symbol shall be cut by computerized plotter or digital printed on retro reflective sheet with high quality eco solvent digital roland and fabricated out of high internsity prismatic grade sheeting with text matter ( as reqd ) and border of same sheeting.signboard shall be supplied along with supported circular hollow stainless steel section frame of size 25mmx25mmx1.29mm thick along with proper clamping with same section of stainless steel and nut bolts / welding, complete all as specified and directed. 31 s&f guide post delinators model no. 952 gp abs round body fitted with 2 nos 100 mm dia highly reflective reflectors made out of pmma and mounted on ms pipe of 50 duly powder coated, anti rust & anti theft steel net make ( dark eye ) complete fixing incl necessary excavation, pcc etc required complete all as specified and as directed by the engineer in charge. 32 taking down carefully copper / aluminium point wiring ( light, fan, socket or power ) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from siteand making good disturbed surface of walls, floors etc complete all as specified and as directed by the engineer in charge. 33 disconnecting unserviceable sub main wiring / service connection of any size and including steel conduit and accessories and removing from site and making good the disturbed surfaces complete all as specified and as directed by the engineer in charge. 34 taking downmcb dbs complete with mcbs / isolator etc removing materials from siteand making good disturbed surface of walls, floors etc complete all as specified and as directed by the engineer in charge. 35 m&l for point wiring with 1.5 sqmm, pvc insulated, unsheathed, stranded copper conductor single core frls cable, is 694 marked, drawn through and including non metallic rigid pvc concealed conduit 20mm dia or higher complete with all pvc conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. / fittings isi marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 sqmm stranded copper conductor pvc insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for: 36 one light point controlled by one, one way switch. 37 one ceiling fan / exhaust fan point controlled by one, one way switch. 38 one three pin 5 amp socket on same board with other switches. 39 one 3 pin 5 amp socket on independent board. 40 all as per item no. 35.00 here in before but with 2.5 sqmm, for one 5 pin 5 / 15 amp socket on independent board including 2.5 sqmmstranded copper conductor ( frls ) pvc insulated green in colour as continous earth conductor connected to common earth complete all as specified and as directed by the engineer in charge. 41 s&f of submain wiring with two runs of single core pvc insulated and unsheathed multistranded ( frls ) copperconductor cable of size 6.00 sqmm lt, 1100 volts grade, drawn through and including 25 mm dia or higher pvc nonmetallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistrandedcopper conductor cable green colour as earth continuity conductor complete all as specified and as directed by the engineer in charge. 42 s&f switch piano flush type 5 amps, single pole one way 240 volts complete all as specified and as directed by the engineer in charge. 43 s&f switch piano flush type 15 amps, single pole one way 240 volts complete all as specified and as directed by the engineer in charge. 44 s&fsocket outlet 3 pin 5 / 6 ampflush type complete all as specified and as directed by the engineer in charge. 45 s&fsocket out let 2 in 1, multipurpose 3 pin 15 / 16 amp flush type isi marked complete all as specified and as directed by the engineer in charge. 46 s&f ceiling fan regulator electronic flush , steped ( four step ) 230 volts ac complete all as specified and as directed by the engineer in charge. 47 s&f ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified and as directed by the engineer in charge. 48 s&f of lamp holder pvc / polycarbonate type with back plate complete all as specified and as directed by the engineer in charge. 49 s&f led tube light fitting in acrylic linear tube ( 1x 18 watt ) , 230v for single led tube lightincluding 1 x 18 w ledretrofitbar professional cw 6500 k cover channel, bipin holders, led power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. make : havells cat part no photonultra2.01212t8sstl20wled 865spc ( for tube ) regalbattent8upto1x22wdsbswh ( for batten ) bajaj cat part no blrb 18w cwc for tube , blrb db 118 for batten , or equivalent model of philips / crompton 50 supply and fixing led light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.make : bajaj / havells / cg 51 s & f led light fitting 1x10wbulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.make : bajaj / havells / cg 52 supply and fixing testing and commissioning energy saving street light luminaire 35 watt led , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete, ip 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by engr in charge. make havells cat part no enduracityliteplat plussl35wled757sasybopc or equivalent model ofsurya / control& switchgear / bajaj 53 supply and fixingstreet light bracket made of 32 mm gi pipe , 1.2 mtr lenght fixed withtwo nos of clamp , nut and bolts for fixing of street lightcomplete all as specified and directed by engr in charge. 54 s & f of mcb sp, 240 volt, 6 amp to 40 amp capacity, 10 ka, c curve complete all as specified and directed. 55 s & f of mcb spn, 240 volt, 63 amp capacity, 10 ka, c curve complete all as specified and directed. 56 s&f of mcb distribution board single pole & neutral with 200 amps rated bus bar, double door ip 43 dbs , made outof sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing mcbs including blanking platecomplete all as specified and as directed by the engineer in charge. 57 s&f exhaust fans ac single phase 230v of size 300mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed.make : usha / crompton / bajaj 58 m&l for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore gi med grade with funnel and wire mesh pcc chamber in cement concrete 1:3:6 type c 2 and rcc cover with handle all as specified and shown in elect plate no 3 of ssr part i of 2009 incl dismantling of old unserviceable existing earthing complete all as specified and as directed by the engineer in charge. 59 s&f of led lamp 9 / 10 watt complete all as specified and as directed. make : havells / crompton / bajaj / usha 60 supply & fixing ceiling fan 1200 mm sweep , 230 volts, ac , 50 hz, copper winded motor, bee 5 star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy complete all as specified and as directed.make: crompton / havells / orient 61 s&f single pole and neutral enclosure with a two pin and earth plug and earth plug and socket complete with one single pole 20 amp mcb sp c series for ac complete all as specified and directed. 62 supply, laying and testing cable xlpe insulated , screened, pvc bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and as directed by the engineer in charge. 63 supply and fixingtubes light grade gi tubing 40 mm dia withall fitting laid in trenches, fixed on pole / on wall for cable protection complete all as specified and as directed by the engineer in charge. 64 excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft / loose soil complete all as specified and as directed. 65 returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft / loose / hard / dense soil complete all as specified and as directed. 66 removing excavated material ( soils ) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point 67 supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed.note: depth of sand cushioning will be measured after punning down and levelling the sand properly. 68 m&l for laying of bricks locally available sub class b bricks, non modular sizes as per is 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed. 69 total in figures 70 quoted amount in words...

Rajasthan Cooperative Dairy Federation Limited - Rajasthan

34047381 supply of isi marked aluminium milk can of cap. 40 litre with lid, aluminium milk can lid for 40 litre cap. milk cans as per isi specifications and milk cans ( aluminium alloy ) isi marked cap. 40 litre with lid under buy back system , isi marked aluminium milk can of capacity 40 litre with lid on running rate contract basis for one year. , aluminium milk can lid for 40 litre capacity milk cans as per isi specifications on running rate contract basis for one year. , milk cans ( aluminium alloy ) isi marked capacity 40 litre with lid under buy back system on running rate contract basis for one year....

Rajasthan Cooperative Dairy Federation Limited - Rajasthan

34040346 supply of isi marked aluminium milk can of cap. 40 litre with lid, aluminium milk can lid for 40 litre cap. milk cans as per isi specifications , milk cans ( aluminium alloy ) isi marked cap. 40 litre with lid under buy back system...

Central Reserve Police Force - Rajasthan

34026795 bids are invited for opc 43 grade cement , acrylic distemper 1st quality , white cement , synthetic enamel paint , putty for wood work , thinner , sandpapers of assorted gratings , 4mm thick sheet of aluminium alloy grade for aluminuum formwork , stainless steel kitchen sink without drain board , fine sand , wire brush , white vitreous china dual purpose closet anglo indian w c suitable for use as squatting pan or european type water closet as per manufacturers specifications , 8 mm dia c.p. brass s s jet with flexible tube upto 1 metre long with s s tringular plate for eureopean type w c , 2nd class teak wood moulded beading or taj beading , patti putty , paint brush 2 inch , paint brush 4 inch , paint brush6inch , paint roller brush , stainner , gi elbow 15 mm , c.pbrass shower , 1.5 sq mm isi marked, frls pvc insulatedsingle core copper conductor cable , 2.5 sq mm isi markedfrls pvc insulated, single core copper conductor cable , 3mm thick phenolic laminated sheet , ceiling rose, 3 pin, 5amps isi marked , s p 5 to 6 amps one way modular switchisi marked , modular base and cover plate for 3 module ,modular base and cover plate for 6 module , astrononicaltime switch suitable for 2 output , 3 pole mccb 100a 16ka ,3 pole mccb 150a 16ka , 18 watt led tubelight total quantity : 55633...

Rajasthan Cooperative Dairy Federation Limited - Rajasthan

34023414 provide of isi marked aluminum milk can of cap. 40 litre with lid, aluminum milk can lid for 40 litre cap. milk cans as per isi specifications , milk cans ( aluminum alloy ) isi marked cap. 40 litre with lid under buy back system...

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

33977251 supply and installation tools, equpment &amp furniture for lab of vocational education 1 ambu mask (adult) 1600ml. self inflating double ended silicone bag with mounts incorporating reservoir valve and side feed oxygen inlet. nos 3 2 aed trainer with adult pad vermed physio control multifunction defibrillator nos 1 3 stop watch royals digital stopwatch timer nos 3 4 oxygen cylinder portable oxygen cylinder (10 l, 150 breaths) nos 1 5 oxygen key for in gas cylinder nos 1 6 oxygen cylinder trolley suitable for 20 litre size gas cylinder nos 1 7 hospital bed single function bed in which head end of the patient can be raised with a handle length: at least 2000 mm ,breadth at least 900 mm & height at least 500 mm nos 2 8 bedside locker • 760mm l x 360mm w x 750 mm h • square & rectangular tube frame • ss top • trolley mounted on 50 mmdia wheels • pre treated & powder coated made of square / rectangular tube frame as well as stainless steel top and trolley mounted famish on 50 mmdia wheels isi / ce certification nos 2 9 cardiac table over bed table (cardiac table) table top height adjustable • frame: tubular mild steel. • finishing: epoxy powder coated, chrome plated adjustable nos 2 10 mattress alternating pressure mattress system with adjustable pump the otica alternating pressure mattress was designed specifically to provide relief from bed sores and ulcers caused from prolonged bed rest. nos 2 11 bed sheet, pillow, pillow cover made from cotton. size approx. : 145 x 225 cm. nos 4 12 blanket pure woollen hosiery blanket single bed 13 wheel chair nylon upholstery • full length arms padded • carry straps on seat allow for ease of folding and lifting • footrest • fold down back • light weight nos 2 14 walker standard oem product nos 2 15 crutch standard oem product nos 2 16 table (3 ft by 6 ft) made of wooden nos 2 17 cupboard steel cupboard for storage nos 1 18 stretcher should be light, safe and reliable, made of aluminium 1alloy and hold for the same, easy to lock and unlock features product dimensions: 192 x 43 x 8cm net weight: 9kg stretcher bearing: 120kg nos 1 19 cane 360 degree anti slip pivoting base provides easy walk on all terrain. the support weight is up to 100 kg, 5 levels adjustable height from 34 inch to 39 inch in 1 inch increment. this walking stick provides additional support for people with arthritic / painful hands when walking indoors and outdoors. nos 4 20 back rest • angle adjustable • foldable for easy storage nos 4 21 foot rest overall approx. step size: 505l x 305w x 230h mm. 800 • frame made of 1 x 18g crc tubes fitted with pvc stumps. • pre treated & epoxy powder coated. nos 4 22 steel basin (large) stainless steel kitchen sink (16 x 18 x 8 inches, silver) nos 4 23 bed pan standard product nos 24 urinal (male) nos 2 25 urinal (female) nos 2 26 air cushion standard oem product nos 2 27 sand bag standard oem product nos 2 28 weighing machine standard oem with isi / ce certification nos 1 29 steel tray (large) standard product nos 8 30 steel tray (medium) nos 8 31 artery forcep standard product rust free nos 5 32 dissecting forcep nos 8 33 scissor 34 nail cutter & filer nos 5 35 splint (large) malleable splints, made of aluminium alloy, can be strapped, x ray compatible, easy to fix nos 10 36 splint (medium) malleable splints, made of aluminium alloy, can be strapped, x ray compatible, easy to fix nos 10 37 splint (small) malleable splints, made of aluminium alloy, can be strapped, x ray compatible, easy to fix nos 10 38 cervical collar (large) standard oem with isi / ce certification nos 6 39 cervical collar (medium) standard oem with isi / ce certification nos 6 40 cervical collar (small) standard oem with isi / ce certification nos 6 41 spine board standard product •tapering from approx. 18 to 14 from head end to foot end. 74.2 long x 3.2 high at height of concave patient surface. • internal padding non absorbent, contoured, bevelled edges, adhesive backed, easy for sanitizing and reapplying. 65 x 11.375 x 6mm. nos 4 42 steel plate standard product rust free nos 4 43 steel glass nos 4 44 steel bowl nos 4 45 spoon nos 8 46 steel jug nos 2 47 bath tub standard product nos 2 48 kidney tray standard product large & small nos 2 49 iv stand • 22 diameter chrome plated heavy bar steel base • lock to ensure secured height positioning • twohook rams horn with secure grip tips • based on a four leg stand • height adjustment from 51 1/2 to 93 • bottom pole diameter is 1, upper pole diameter is 0.75 nos 2 50 measuring glass standard product non breakable nos 4 51 measuring tape standard product nos 4 52 goggles 53 suction apparatus a/c power with collection capacity of 200 ml with 20 litres per minute flow rate. backup for 20 min. provision with manual operation in case of any power failure nos 2 54 syringe destroyer standard oem with isi / ce certification electronic with cutter. nos 4 55 syringe steriliser nos 4 56 needle burner nos 1 57 thermometer nos 8 58 syringe 50 cc/ml nos 8 59 b.p. monitoring machine nos 5 60 hot water bottle as per standard nos 6 61 ice caps as per standard nos 4 62 transfer forceps as per standard nos 4 63 drum as per standard nos 1 64 dressing kit as per standard nos 1 65 dressing scissor as per standard nos 5 66 folley catheter as per standard nos 2 67 euro bags standard oem with isi / ce certification nos 6 68 ryle’s tube as per standard nos 4 69 vaccutanour (red/black/viol et) as per standard nos 10 70 tourniquet as per standard nos 2 71 examination table as per standard nos 1 72 call bell as per standard nos 2 73 rubber sheet/mackinto nossh as per standard nos 10 74 draw sheet as per standard nos 4 75 bandage as per standard nos 10 76 suction catheater as per standard nos 2 77 bulb syringe as per standard nos 2 78 oxygen mask 79 stethoscope double sided aluminium chest piece with matt anodising. it is precisely machined for enhanced performance & durability. it features dual tunable diaphragms with brass chrome plated rings. the larger diaphragm is used for adult patients whereas the smaller diaphragm is used for paediatric patients. nos 5 80 towel cotton nos 4 81 gown different size nos 10 82 gloves (disposable) – packet as per standard nos 8 83 gloves (surgical) – packet as per standard nos 8 84 liquid soap bottle as per standard nos 4 85 mask – packet as per standard nos 4 86 shoe cover packet as per standard nos 4 87 hair cap packet as per standard nos 1 88 sponge cloth as per standard nos 2 89 wet wipes packet as per standard nos 2 90 comb as per standard nos 4 91 tooth brush as per standard nos 4 92 toothpaste as per standard nos 2 93 hair oil as per standard nos 2 94 shampoo bottle as per standard nos 2 95 bath soap as per standard nos 8 96 talcum powder as per standard nos 2 97 different colour plastic bags with dustbins (red) as per standard nos 1 98 different colour plastic bags with dustbins (blue) as per standard nos 1 99 different colour plastic bags with dustbins (black) as per standard nos 1 100 different colour plastic bags with dustbins (yellow) 101 uro bag t tap type 2000 millilitre nos 10 102 sample collection bottle as per standard nos 10 103 gauze piece (4x4) as per standard nos 10 104 betadine solution bottle germicide gargle nos 4 105 cotton rolls as per standard nos 2 106 cotton absorbent supper cotton nos 2 107 normal saline bottle as per standard nos 2 108 micro pore 9.14 meter (length on a roll) without dispenser surgical tapes nos 5 109 spatula to collect pep smear, cytology specimen. nos 10 110 hydrogen peroxide bottle stabilized hydrogen peroxide nos 2 111 cleaning solution (colin) as per standard nos 2 112 stationary set multi functional multi toolkit for office works, stationary organizer | stapler, scissor, punch, ruler, sharpener, opener, remover, ring, clip holder (all in one kit) nos 5 113 paper (ream of 500) a4 size nos 1 114 extension cord with 4 sockets nos 1 115 speaker as per standard nos 1 116 fire extinguisher 2 kg nos 2 117 alcohol based hand sanitizer herbal, alcohol nos 5 litre 118 n 95 mask capelo with exhalation valve nos 10 119 rubber gloves latex water proof hand gloves pairs nos 10 120 unbranded steel tool box for basic tools nos 1 121 temperature gun non contact digital infrared thermometer nos 2 122 manikin (male & female) standard oem with isi / ce certification nos 1 each 123 oximeter finger tip pulse oximeter with spo2, p ...

Airports Authority Of India - Rajasthan

33896386 bids are invited for supply of heavy duty alluminium alloy tiltable tower , supply of heavy duty aluminium industrial ladder , supply of heavy duty aluminium stool cum ladder , supply ofmicroprocessor controlled digital meggar , supply of digitallux meter with rangeprovision of various electrical tools and plants at civil total quantity : 5...

Rajasthan State Sports Council - Rajasthan

33500157 sports equipment supply of various sports equipment of sports games , archery , arrow wooden bamboo made with nock & point complete with fletches , arm guard plastic made with fine elastic & proper grip , finger tab ordi leather made with fine elastic & proper grip , target face 40 cms threaded paper with proper marking, as per international norms & standards , target face 80 cms threaded paper with proper marking, as per international norms & standards , target face 122 cms threaded paper with proper marking, as per international norms & standards , target face 6 ring threaded paper with proper marking, as per international norms & standards , arrow rest metal wire , target butteress compound jute made with proper infilled with wastage, as per international norms & standards , target stand four leg wooden made, with folding legs & proper painted , side quiver matti made with belt, long quiver , target pin polycarbonate with fibe nock, as per international norms & standards , chest guard met material with fine elastic & proper grip , bow wooden bamboo made with stabilizer , spine vanes spin wing, as per international norms & standards , arrow x 10 ( impo. ) complete barreled carbon with nock & point complet with fletches, as per international norms & standards , bow complete set compound all are perfect equipment for professional use, as per international norms &standards , bow complete set recurve ( imported ) all are perfect equipment for professional use, as per international norms &standards , nook biter polycarbonate made , flex packet as per international norms & standards , spin wing spin wing, as per international norms & standards , bow stand indian metallic made , carry bag matti made , tungustion point as per international norms & standards , athletic , high jump stand mettalic / aluminium, heavy base with proper marking, as per international norms & standards , high jump mat with rain cover&trolley made of high density foam with rain cover & mettalic trolley on wheels, standards size, as per international norms & standrds , cross bar high jump fiber fiber made with plastic ends on both corners, length 4mtr, as per international norms & standards , hurdle training adjustable height forn training purpose only , hammer iron 7.26kg round shape with handle & wire, as per international norms & standards , hammer iron 3kg round shape with handle & wire, as per international norms & standards , hammer iron 4kg round shape with handle & wire, as per international norms & standards , hammer iron 5kg round shape with handle & wire, as per international norms & standards , hammer iron 6kg round shape with handle & wire, as per international norms & standards , hammer iron 7kg round shape with handle & wire, as per international norms & standards , hammer iron 16 pond ( 7.26kg ) round shape with handle & wire, as per international norms & standards , hammer iron 12 pond ( 5.45kg ) round shape with handle & wire, as per international norms & standards , hammer wire with handle aluminium / mettalic, as per international norms & standards , relay batton pvc made, florocent & assorted colours, standard size, as per international norms & standards , stop board ( toe board ) wooden / aluminium made, as per international norms & standards , stop watch 100 mm electronic 100 lap manoery, 1 / 1000 second stop watch, measuring mode elapsed time, lap time, split time, lap counter, ( up to 99 ) , beeper sound alarm, regular time keeping hours, minute, second, am / pm, year, month, date, day , shotput iron 3kg turned & round shape with proper grip, as per international norms &standards , shotput iron 4kg turned & round shape with proper grip, as per international norms &standards , shotput iron 5kg turned & round shape with proper grip, as per international norms &standards , shotput iron 6kg turned & round shape with proper grip, as per international norms &standards , shotput iron 6.26kg 119mm to 121mm turned & round shape with proper grip, as per international norms &standards , shotput iron 7.26kg 120mm to 129mm turned & round shape with proper grip, as per international norms &standards , strating block steel / aluminium made, heavy slotted channel, extra large paddles for easy start, as per international norms & standards , discus 1kg fiber made, durable quality & proper grip, as per international norms & standards ( , discus 1.50kg fiber made, durable quality & proper grip, as per international norms & standards , discus 1.75kg fiber made, durable quality & proper grip, as per international norms & standards ( vinex / nelco / ate or equivalent ) , discus 2kg fiber made, durable quality & proper grip, as per international norms & standards , discus 750gms fiber made, durable quality & proper grip, as per international norms & standards , discus 700gms fiber made, durable quality & proper grip, as per international norms & standards , discus 600gms fiber made, durable quality & proper grip, as per international norms & standards , discus 1.25kg fiber made, durable quality & proper grip, as per international norms & standards , hammer handle aluminium / mettalic, as per international norms & standards , hanging bell brass made with heavy metallic base for proper stability wuth wheels , polymatric box metallic made, powder coated, top covered with rubber sheet , javelin 600 gms range 60 70 mtr made of hardened best quality dura aluminium, designed crafted of maximum throw distance, javelin head made of stainless steel for extra durability, as per international norms & standards , javelin 700 gms range 70 80 mtr made of hardened best quality dura aluminium, designed crafted of maximum throw distance, javelin head made of stainless steel for extra durability, as per international norms & standards , javelin 800 gms range 70 80 mtr made of hardened best quality dura aluminium, designed crafted of maximum throw distance, javelin head made of stainless steel for extra durability, as per international norms & standards , javelin 500 gms made of aluminium alloy extra durability & stability, javelin head made of steel for extra durability, as per international norms & standards , javelin 600 gms made of aluminium alloy extra durability & stability, javelin head made of steel for extra durability, as per international norms & standards , javelin 700 gms made of aluminium alloy extra durability & stability, javelin head made of steel for extra durability, as per international norms & standards , javelin 800 gms made of aluminium alloy extra durability & stability, javelin head made of steel for extra durability, as per international norms & standards , nokal ball javelin pvc made, accurate shape & weight , pole vault fiber fiber glass made, as per international norms & standards , pole vault stand metallic made, adjustable height 366cms to 640 cms, as per international norms & standards , pole vault upright with box metallic / stainless steel made, box socket at bottom for drainage of water, as per international norms & standards , pole vault fiber cross bar 4.5mtr. fiber made with plastic ends on both corners, length 4.5mtr, as per international norms & standards , kettle ball 60kg metallic made with proper grip, for training , drag run metallic made, size 4ft x 2ft approx, for training , gym ball 75cms anti burst material with foot pump, for training , gym ball 85cms anti burst material with foot pump, for training , swiss ball anti burst material, for training , agility ladder plastic made, for training , exercise roller eva foam material, water proof & anti slip, for training , ab roller non slip grip for stability & control & non skip wheels, for training , running parachute parachute cloth, for training , theraband latec rubber material, for training , long jump take off board wooden / aluminium made, as per international norms & standards , handles ( hurdle ) steel / aluminium made, wider flat base for superior on the ground, weight of the hurdle adjusts automatically according to the height regulation tip over position, as per international norms & standards , jumping box ( spring board ) made off laminated plywood with very heavy & strong steel frame with heavy duty springs, upholsteed with high quality carpet, as per international norms & standards , take off board wooden / aluminium made, as per international norms & standards , pole vault pole fiber fiber glass, approved by laaf, as per international norms & standards , pole vault pit p.u foam especially designed for smooth & soft landing cover made vinyl fabric for extra durability with metallic trolley, mesh top allows desired escape of air to provide maximum compression on landing, laaf approved , pole vault uprights iron / stainless steel, extension arm for safety, adj. height 366 640 cms, approved by laaf , high jump uprights iron / aluminum height adjustable: 160 cms to 270 cms, laaf approved , high jump pit p.u foam especially designed for smooth & soft landing cover made vinyl fabric for extra durability with metallic trolley, mesh top allows desired escape air to provide maximum compression on landing, laaf approved , boxing , boxing gloves 10 oz leather made, moulded shock absorbent foam padded with proper velcro, as per international norms & standards , boxing gloves 12 oz leather made, moulded shock absorbent foam padded with proper velcro, as per international norms & standards , boxing gloves 16 oz leather made, moulded shock absorbent foam padded with proper velcro, as per international norms & standards , boxing head guard leather made with proper padding & proper velcro, as per international norms & standards , punching gloves leather made with proper padding & proper velcro , boxing punching pad leather made with proper padding, proper grip & protection , boxing punching bag leather leather made, compressed flock filled with mettalic chain , boxing ring complete set made of heavy duty steel for extra stability and durability of the ring. corner posts made of heavy duty steel ( 4’’ diameter ) with screw loops for tightening the ring ropes.ropes are fully adjustable and are covered with the finest quality fabric.corner cushions’ covers are made of pvc coated fabric and filled with extra durable dense foam for better protection. floor cushions are made of 10 mm closed cell high density e.p. for hock reducation. floor is covered with pvc coated fabric for non slippery surface. platform made of sensoned hard wood. also includes 2 stools, 2 spit bins and 3 stairs. , badminton , shuttle cock feather duck / goose feather, 16 to 18 feathers, fixed in base of cock with proper flight, as per international norms & starndards , shuttle cock nylon nylon material with basse of cork or foam, with proper flight , badminton net hdpe material, colour drak brown, mesh size 15 20 square mm approx with tetron tape on top end with proper eyelets with nylon dori, as per international norms & standards , badminton racket graphite frame with graphite shaft, synthetic grip with proper gutting, as per international norms & standards , portable synthetic court flooring synthetic flooring with proper marking & installation etc., as per international norms & standards , basketball , basketball post fixed type, heavy duty pipe, complete set with boards, rings & nets etc., as per international norms & standards , basketball net nylon made, white colour with 12 loops, as per international norms & standards , basketball rubber no 6 rubber material, circumference 28.5 to 29 , weight 18oz to 20oz, as per international norms & standards , basketball rubber f / s 7 rubber material, circumference 29.5 to 30 , weight 20oz to 22oz, as per international norms & standards , basketball leather f / s 7 leather pasted, circumference 29.5 to 30 , weight 20oz to 22oz, as per international norms & standards , basketball fiber board boards made of acrylic fibre sheet with mettalic frame on alll around corners with proper marking, as per international norms & standards , basketball ring made of 20mm thick solid pipe with proper hooks to tie with net. , cricket , cricket bat e / w full size english willow standard size & width with cane handle, well balanced & striking power with fine grip, as per icici rules , cricket bat k / w full size kashmir willow standard size & width with cane handle, well balanced & striking power with fine grip, as per icici rules , cricket bat k / w size no. 6 kashmir willow with cane handle, well balanced & striking power with fine grip , cricket bat k / w size no. 5 kashmir willow with cane handle, well balanced & striking power with fine grip , cricket ball leather match quality made of leather, standard size & weight, hand stitched, as per icici rules for pratic quality , cricket ball leather practice quality made of leather, standard size & weight, hand stitched, as per icici rules for pratic quality , cricket net 100x15 made of thick hdpe material with interlocking on all around corner with nylon dori, mesh size 1.75 square inch approx, , cricket ball synthetic made of synthetic material for practice , cricket ball tennis made of fine felt & proper bounce , elbow guard made of foam filled with eva or equivalent material for protection fine velcro , batting gloves full size made of foam or leather filled with cotton or equivalent material for protection & velcro for proper grip, as per norms & standards of icici , helmet made of protective material with padding inside for proper grip with metallic or titanium grill for protection, as per norms & standards of british , abdominal guard for batsmen made of very protective plastic or equivalent material , cricket matting full made of 4 shaft jute coir with lining on all corner for better life, size 66x8 approx for pratice purpose , cricket matting half made of 4 shaft jute coir with lining on all corner for better life, size 33x8 approx for pratice purpose , thigh pad made of foam filled with eva or equivalent material with velcro attached, as per icici rules , batting legguard full size made of foam or leather filled with cotton or equivalent material for protection & velcro for proper grip, as per norms & standards of icici , wicket keeping pad full size made of foam or leather filled with cotton or equivalent material for protection & velcro for proper grip, as per norms & standards of icici , wicket keeping gloves made of foam or leather material with cotton or eva or any other protective material with rubber pimpled grip on palm side, as per norms & standards of icici rules , stumps with bails made of wood, natural or polised with wooden bails, as per norms & standards of icici rules , pitch roller petrol / diesel operated capacity 1 / 2 ton as per international norms & standards , pitch roller petrol / diesel operated capacity 1 ton petrol / diesal operated capacity 1 ton with heavy duty engine, speed should be maximum 5kmph, minimum 30liter tank capacity with mechanical steering with proper head light, latest design or pattern , grass cutter grass cutting machine, main deck made of steel with heavy duty engine with fuel tank capacity of more than one liter, latest pattern , football , football synthetic or p.u. material, standard size no. 5 with bladder, properly stiched, circumference 68 to cms, weight 410 to 450 gms, as per international norms & standards , football net hdpe material with dori, mesh size 120 square mm approx., as per international norms & standards , shoting board wooden with mettalic frame, portable type , target ring parachute cloth with proper holes with marking & fixed with two vertical plastic poles , football pendulam synthetic or p.u. material with polyprolene or nylon dori stiched with football for hanging purpose , handball , handball synthetic men size synthetic made, size no 3, circumference 56 58 cms, weight 425 to 475 gms, as per international norms & standards , handball synthetic women size synthetic made, size no 2, circumference 52 54 cms, weight 325 to 375 gms, as per international norms & standards , handball synthetic mini size synthetic made, size no 1, circumference 48 50 cms, weight 225 to 275 gms, as per international norms & standards , handball goal post mettalic, made of 80mm square pipe, size 3mtr x 2mtr with back support, portable type with proper painted , as per international norms & standards , handball net hdpe / polyproplene material with dori, as per international norms & standards , hockey , hockey fiber hockey stick made of 100% glass fiber material with p.u grip, with astro truff pattern blade shape, length 35 to 37.5, as per international norms & standards , hockey stick wooden hockey stick made of cane material with p.u grip, with astro truff pattern blade shape, length 35 to 37.5, as per international norms & standards , hockey stick graphite hockey stick, made of composite material of carbon, kelvar fiber & glass fiber with p.u grip, with astro truff pattern blade shape, length 35 to 37.5, as per international norms & standards , hockey stick carbon hockey stick, made of composite material of maximum quantity of carbon material alongwith kelvar fiber with p.u grip, with astro truff pattern blade shape, length 35 to 37.5, as per international norms & standards , hockey truf ball hockey ball, made of eva material, hollow inside pattern, dimple shaped for astro truff, dia of ball 2.8 to 2.96, weight 153 to 158gms, as per international norms & standards , hockey helmet fine material with proper padding inside for better grip, should be completely protective , shin guard moulded with proper grip & protection, as per international norms & standards , hockey net hdpe material with dori, as per international norms & standards , hockey goal post wooden / mettalic, width 12ft x height 7ft, as per international norms & standards , goal keeper kit full light weight, all equipments well protected, goal keeper kit should br consisting of these items helmet, chest guard with shoulder guard, hand gloves, abdominal guard, padding shorts, legguards, kicker, over t shirts & shorts, shoes, stocking, teeth guard, neck guard, goolie stick, kit bag, as per international norms & standards , rebound board wooden with mettalic frame, portable type , hand gloves made of lykra cloth with plastic on knuckle portion for protection, with proper velco, as per international norms & standards , face mask made of polycarbonate with proper grip & visibilty, as per international norms & standards , lawn tennis , lawn tennis ball made of fine felt with proper pressure & bounce, size 2.57 to 2.70 in diameter, weight 1.98 oz to 2.10 oz., yellow colour packed in vaccum proof box, should be ideal for all courts, as per international norms & standards , racket made of 100% graphite material with p.u grip, as per international norms & standards , net made of hdpe material with non tearing top tape, mesh size of 2 square inch approx., length 42ft x width 3.5ft, as per international norms & standards , trolley mettalic with wheels , cone ( small ) made of plastic / pvc, uv treated, florosent colours, size 9 approx. , racket overgrip soft material with proper elasticity & grip , string reel ( 200m ) made of polyster material with maximum power and control, length 200mtr , netball , netball synthetic / rubber made, hand stitched with latex bladder inside, standard size & weight, as per international norms & standards , netball net nylon made, white colour with 12 loops, as per international norms & standards , bibs made of polyster colth, florocent colour with number printing , netball pole fixed / portable type, mettalic complete with mettallic ring & net, as per international norms & standards , table tennis , ball made of plastic plastic made, size 40mm+, colour white, weight 2.7 gms approx, as per international norms & standards , net made of hdpe material, standard size, as per international norms & standards , bat table tennis bat made of ply with red & black rubber on each side of bat, as per international norms & standards , table tennis table made of thick board with mettalic frame with wheels, dupont polyurethane anti glare painted, complete with t.t clumps & net, standards size 2740 x 1525 x 760mm, as per international norms & standards , volleyball , volleyball practice made of synthetic / p.u material, multi coloured, hand stitched with latex bladder inside, diameter 65 to 67 cms, weight 260 to 280gms, as per international norms & standards , volleyball leather pasted made of leather pasted, multi coloured, hand stitched with latex bladder inside, diameter 65 to 67 cms, weight 260 to 280gms, as per international norms & standards , volleyball net twistered hdpe thread material, size 10mtr x 1mtr, non tearing vinyal all around tape, machine knitted, uv treated, mesh size 10cms ( approx. ) , pvc coated metal wire with rust proof eylets, as per international norms & standards , volleyball antena made of fiber glass, colour preferbly red & white with non tearing marking tape, as per international norms & standards , volleyball pole mettalic with adjustable height pattern, complete with pullies & tightner etc., as per international norms & standards , wrestling , wrestling mat with cover made of japanease synthetic rubber ( jsr ) sheet, size 144 sqmtr, consisting of 72 mats of size 2mtr x 1mtr with velcro attached on mats whenever required with single pc., non tearing material cover with proper marking, as per international norms & standards , rassa thick jute or p.p made with hooks on top end for hanging, length 7mtr , wrestling dunny made of non tearing material with rubber or cotton filled, with proper grip etc., different weights , judo , judo mat made of japanease synthetic rubber sheet & epe material, size 196sqmtr, consisting og 98mats of size 2mtr x 1mtr, single mats with non tearing cover and non slippery bottom, as per international norms & standards , judo dress made of cotton fabric with belt with proper grip, colour: white & blue both, as per national norms & standards , kho kho , kho kho pole wooden made, as per international norms & standards , general , skipping rope made of pvc rope with plastic handles, perferbly with ball bearings, length 9ft approx. , foot pump foot operated with meter , medicine ball 1 kg rubber or synthetic made with proper & fine grip , medicine ball 2 kg rubber or synthetic made with proper & fine grip , medicine ball 3 kg rubber or synthetic made with proper & fine grip , medicine ball 4 kg rubber or synthetic made with proper & fine grip , medicine ball 5 kg rubber or synthetic made with proper & fine grip , stop watch electronic beep alarm with chime & snooze, 30 second correction for 12 / 24 hour, disply for user option, maximum counting 20hours, 59 minutes, 59 seconds , stop watch 100 lap manoery, 1 / 1000 second stop watch, measuring mode elapsed time, lap time, split time, lap counter, ( up to 99 ) , beeper sound alarm, regular time keeping hours, minute, second, am / pm, year, month, date, day , weight machine electronic anti skid platform for user safety, auto shutt off, capacity 150kgs, overloaded indicator, lcd disply , plastic cone made of plastic / pvc, uv treated, florosent colours, size 9 approx. , measuring tape 100mtr fiber glass material, open frame case with non slip cushion handle rubber grip, protruding marker at the bottom of the case allowa easy measuring of land , measuring tape 50mtr fiber glass material, tape have tensile strength, tape in non conductive, water resistance , softball , ball made of leather , hand stitched, diameter 12inch, weight 177 to 198 gms, as per international norms & standards , batting tee rubber made, for training purpose , bat mettalic with proper grip & striking power, as per international norms & standards , gloves leather made, hand stitched with proper grip & protection, for rigthy & lefty players, as per international norms & standards , net hdpe material with nylon dori, mesh size 1.75 square inch approx, size 100 x20 , helmet helmet with proper padding inside for better grip., should be vert protective, as per international norms & standards , catcher gloves mitt leather made, hand stitched with proper grip & protection, as per international norms & standards , catcher kit catcher kit of fine quality & protection consisting of following things packed in bag chest guard, legguard, mitt, helmet, abdominal guard, inner gloves & kit bag, as per international norms & standards , catcher chest guard foam made with eva sheet inside, proper grip & protection, as per international norms & standards , base plate fixed type, the complete set consisiting of 3pcs bases plate, 1pc triangle plate, 1pc diamond plate, standard size, as per international norms & standards , practice ball plastic plastic made, preferably rubber coated for better grip, for training , weight lifting , weight lifting plateform 4mtr x 4mtr made of very fine wood, portable type size 4mtr x 4mtr, as per international norms & standards , dumbbel good quality metallic dumbbell with rubber coatedfor 2.5kg, 5kg, / 7.5kg and so on good quality metallic dumbbell with vinyl coated for 1 kg, 2kg, 3kg, 4kg, 5kg , weight lifting set one 20 kg olympic lifting barbell, two 2.5 kg steel collars, two 25 k.g bumper plates, two 20 k.g bumper plates, two 15 kg two 10 kg bumper plates, two 5 kg bumper plates, two 2.5 k.g plates, two 1.5 k.g plates, two1 k.g plate, two 500 gram plate as per international norms & standards , wushu , wushu head guard leather made with proper padding & proper velcro, as per international norms & standards , mat made of high density japnease synthetic rubber sheet with non tearing cover size 2mtr x 1mtr., as per international norms & standards , chest guard made of foam with eva material filled inside for proper protection, reversable colour red & blue as per international norms & standards , gloves leather made, moulded shock absorbent foam padded with proper velcro, as per international norms & standards , shin guard made of foam with eva material filled inside for proper protection, with velcro, as per international norms & standards , kicking pad made of foam wirh eva sheet inside with proper grip , punching bag leather made, compressed flock filled with mettalic chain , gymnastic , uneven bar asymmetric bar made of wood, covered with fiber glass for good griping, as per international norms & standards , balancing beam metallic made, adjustable height 1.10 cms to 1.50cms with solid base & support, as per international norms & standards , roman ring made of heavy tubular steel structure 100x50x3 mm pipe with springs & wire etc., as per international norms & standards , jumping board made off laminated plywood with very heavy & strong steel frame with heavy duty springs, upholsteed with high quality carpet, as per international norms & standards , crash mat made of high density p.u foam covered with polyvinyal material, size 3mtr x 2mtr x 30cms, as per international norms & standards , parallel bar made of heavy duty tubular metallic structure with double lockong system & fiber glass bases, adjustable height from 1.20mtr to 2.00 mtr, size 3.5mtr, as per international norms &standards , vaulting table metallic with heavy base with metallic support, lastest pattern, adjustable height 100cms to 135cms with safety padding, as per international norms & standards , pommal horse metallic with heavy base with metallic support & spring , safety system, adjustable height 95 cms to 135cms , as per international norms & standards , wall bar made of superior wood, as per international norms & standards , taewkondo , chest guard made of foam with eva material filled inside for proper protection, reversable colour red & blue as per international norms & standards ( vinex / taishan / nivia or equivalent ) , head guard moulded, pvc material with proper grip, shape & protection, as per international norms & standards , arm guard made of foam with eva material filled inside for proper protection, with velcro, as per international norms & standards , shin guard made of foam with eva material filled inside for proper protection, with velcro, as per international norms & standards ) , punching bag leather made, compressed flock filled with mettalic chain , mat set made of fine eva material, reversable type with interlocking pattern as per international norms & stnadrds , hand gloves made of foam with eva material filled inside, with proper grip & protection, as per international norms & standards , foot guard made of foam with eva material filled inside, with proper grip & protection, as per international norms & standards , power pad made of foam wirh eva sheet inside with proper grip , bag kit pad made of foam wirh eva sheet inside with proper grip , fan pad made of foam wirh eva sheet inside with proper grip , kabaddi , kabaddi mat kabaddi mat : made of fine eva material, reversable type, interlocking pattern, size 400 square mtr, consisting of 400pcs of 1mtr x 1mtr with thickness 35 to 40mm, as per international norms & standards , swimming , kick board kick board is constructed of durable closed cell eva foam, for extended life and performance in the water material : eva foam made of fine eva material with proper grip , line rope antiwave lane made of pvc material with mettalic wire & hooks etc., standards length, as per international norms & standards , pull buoy kick board is constructed of durable closed cell eva foam, for extended life and performance in the water material : eva foam , hand paddles ergonomically engineered shape for improved grip and reduced hand fatigue material : polyprogylene , fins a 100% duraft silicone construction and state of the art comport fit. should be of small length , pace clock with a 15 inch face, this clock style timer is easy to see from far away push button start / stop counts up with 1 second resolution to 60 minuntes then repeats. , trx band resistance bands can be used for multiple exercises, such as general exercises, stretching, strength building, power weight programs. , slam ball heavy duty rubber shell different weights. , swimming stretch cord ( 25m ) long 25m resistance stretch cord with belt for waist. , swim parachute nylon parachute with long cord around the waist. , chin up bar made of heavy duty steel with high density foam grips and upgrade screw, strengthened beams and triangular support structure. , water polo ball yellow ball, fina standards. , water polo goal post. as per international norms & standards...

North Western Railway - Rajasthan

33391122 supply of 3/4 inch sq. drive ratcheting head3/4 inch sq. drive ratcheting head,3/4 inch sq. drive ratcheting head, max. recommended working torque: 480 ft. lbs with torque preset at 590 nm torque, preset click type, interchangeable heads permit ratcheting accuracy: plus/minus 4% (clockwise), plus/minus 6% (counter clockwise) from 20% to 100% of full scale with 02 sockets of size 36mm. made in single piece of aluminium alloy housing. make snapon or armstrong or samtool or gedore. calibration certificate to be provided by nabl accredited lab or oem. certificate of genuineness to be furnished at time of supply by oem/authorised dealer....

North Western Railway - Rajasthan

33391121 supply of sq. drive ratcheting headsq. drive ratcheting head,1/2 inch sq. drive ratcheting head, max. recommended working torque: 240 ft. lbs with torque preset at 340 nm torque, preset click type, interchangeable head permit ratcheting accuracy: plus/minus 4% (clockwise), plus/minus 6% (counter clockwise) from 20% to 100% of full scale with two sockets of size 30mm. made in single piece of aluminium alloy housing make snapon or armstrong or samtool or gedore. calibration certificate to be provided by nabl accredited lab or oem. certificate of genuineness to be furnished at time of supply by oem/authorised dealer. , 3/4 sq. drive cordless impact wrench having brushlessless motor and iq power control system with 4 models: full power, half power, wrench tight and hand tight. free speed: 0 2450 rpm, max. torque: 1000ft. lb. (1360 nm), nut busting torque:1500ft. lb. (2033 nm), weight inclusive battery:3.5 kg approx. with 20v batteries 5 ah 2 nos. and one charger as per ingersoll rand model no. w7172 k22. shall be supplied along with impact socket 3/4x38 mm 02 nos. and 3/4x42 mm 02 nos. (with warranty period of 2 years) make ingersoll rand/atlascopco/uryucalibration certificate to be provided by nabl accredited lab or oem. certificate of genuineness to be furnished at time of supply by oem/authorised dealer....

Military Engineer Services - Rajasthan

33366163 special repair to road and road furniture from cp 01 to mes pump house circle and widening of road from cp 01 to mes power house no. 2 in jodhpur mil stn under ge ( a ) central 1 surface excavation not exceeding 15 cm deep and averaging 15cm deep and getting out in soft / loose soil complete all as specified and directed. 2 m&l for wbm 75 mm thick ( compacted thickness ) in 2 layers, with coarse aggregates of grading 2 ( 63 to 40mm size ) , rolled 8 to 10 tonne power roller and compacted to required camber and gradient complete all as specified and directed. 3 m&l for 200 mm thick soling ( or sub base ) with broken boulders or quarried stone, inter stices filled, surface formed androlled 8 to 10 tonne power roller and compacted to required camber and gradient complete all as specified and directed. 4 preparing surfaces of wbm by brooming with wire brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surfacegunny bag to remove all loose dirt etc complete all as specified and directed. 5 m&l for applying evenly a priming / tack coat with bituminous primer of paving bitumen @ 10 kg per 10 sqm, complete all as specified and as directed. 6 m&l for laying premix bituminous, macadam ( bitumen content 4% by wt of total mix ) laid / rolled and compacted to required gradient and camber ( consolidated thickness 75mm or less ) complete all as specified and directed 7 m&l for applying evenly a priming / tack coat with bituminous primer of paving bitumen @ 5 kg per 10 sqm on blacktop surfaces complete all as specified and as directed. 8 m & l forbituminous premix semi dense asphaltic concrete 30 mm consolidated thickness using paving bitumen vg 30 with 5.5% binder content by weight of total mix. rolled and compacted to required camber and gradient complete, and rolled with 8 to 10 tonne power roller complete all as specified and directed.note : bitumen used in the work shall be paving bitumen grade vg 30 irrespective whatever specified. 9 m & l for stone kerb of roughly squared stones of size 10cm x 30cm, dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in cement mortar ( 1:6 ) and struck flush complete all as specified and directed. 10 m&l for preparing bituminious surfaces of road and marking 2.5 mm thick centre line, stop line, dashes, arrows etc. and the like n. exc 10 cm wide on roads pavements with hot applied thermo plastic road marking paint with 8% glass beads of approved colour confirming to bs 3262 1989 with special applicator machine all as per manufactures instruction complete all as specified and directed. 11 s&f of retro reflective road cat eyes of size 100 x 100 90 x 18 20 mm with fine grained micro glass particles of regular size with bottom portion embedded on road surface using cut back bitumen emulsion complete all as specified and directed. 12 m&l moorum / red bajri spread, rolled and consolidated to gradient alongside paved roads as in berms incld necessary watering & rollingcomplete all as specified and directed. 13 repair to potholes any depth , not exc 1 sqm each including sweeping free from dust and mud or water , scouring sunken surfaces in roads, paths etc cutting around edges to at least 25 mm in depth , making good by filling in sceened & graded road metal, watering and well ramming ( including supply of road metal ) 14 preparing surfaces of existing black top surfaces by brooming with wire brushes for removing caked mud etc sweeping with gunny bag to remove all loose dirt etc andapplying evenly a priming / tack coat with bituminous primer of paving bitumen @ 5 kg per 10 sqm on blacktop surfaces complete all as specified and as directed. 15 s&f in repair solar delinator height 1000 x 47 mm made of polycarbonate and toughened aluminium alloy body. height 145 mm, diameter 80 mm, comprises of 4 super bright leds which give 360 degree viewing. solarpanel 2.5v, 120 mm ( approx ) 1.25 v rechargable battery 01 no, back up 12 hours of continues lighting at night complete all as specified and directed. 16 s&f of solar reflective studs abs body 100 x 100 x 18.50mm blinker high quality and fixed with epoxy adhesive as approved by ge & as directed by engineer in charge. 17 s & f in repair factory madereflective safety traffic mirror, 900 mm dia for road and side walk of stainless steelface, 0.90 mm thick large radius of curvature for minium distance distrotation orange powder coated steel back and hood orange vinyl extrusion with 75 mm clamp brackets for pole mouting complete all as specified and directed. 18 m&l for chipping damaged surface of road thickness not more than 50 mm all as directedincluding removing screened materials to out side mod land, complete all as specified and directed....

North Western Railway - Rajasthan

33166933 supply of 3/4 inch sq. preset torque3/4 inch sq. preset torque,3/4 inch sq. preset torque with preset value locking and safety device made in single piece of aluminium alloy housing to be fixed at 250nm,(torque range 140 620 nm) with following accessories 1, 3/4 inch ratchet head fitting 01 no 2open end fitting (size 46 mm) 01 no 3 ring and fitting (size 46mm) 01no make inger soll rand ,chicago pneumatic snapon or armstrong or samtool or gedore.calibration certificate to be provided by nabl accredited lab or oem. certificate of genuineness to be furnished at time of supply by oem/authorised dealer....

North Western Railway - Rajasthan

33149413 supply of preset torque wrenchpreset torque wrench,preset torque wrench with pre set value locking and safety device having a spigot dia. of 16 mm. required specifications: (1)made in single piece of aluminium alloy housing (2)to be fixed at: 200 nm (3)torque range: 80 400 nm (60 300 lbf. ft.) (4)weight: 2.000kg (5)length: 633mm (6)supply along with suitable end fitting and socket (7)1/2 sq. drive ratchet head (8)1/2 sq. drive socket size: 30mm make:bosch/gedore/griphold/armstrong/facom/proto/ridgid. calibration certificate to be provided by nabl accredited lab or oem. certificate of genuineness to be furnished at time of supply by oem/authorised dealer....