Military Engineer Services - Rajasthan
40876286 tender for periodical services including certain b / r and e / m repair work to various ascon nodes under age b / r ii at suratgarh mil stn ; 1 demolition of brick work, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by engineer in charge. 2 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) and rubbish off the premises complete all as specified and directed by engineer in charge. 3 dismaintling of wall and ceiling boards ( fibre, pulp, insulation, etc. ) or insulation boards / slabs / blankets, any thickness, including cover fillets including cover fillets complete all as directed by engineer in charge. 4 dismantling asbestos cement sheet ( corrugated, semi corrugated etc ) as in roofs etc including ridges complete all as specified and directed by engineer in charge. 5 dismantlig of timber scantling unframed work under 40 sqcm in section as in fillets, rails, posts, rafters, purlins in any position complete all as specified and directed by engineer in charge. 6 taking down steel window / ventilator of any description and of any type with or without guard bars and making good the disturbed portion complete all as specified and directed by engineer in charge. 7 taking down cement plaster or cement lime plaster on stone surface / brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by engineer in charge. 8 taking down chowkat or frame with shutters including fitting and fixtures area not exc 1.5 sqm each ( without taking off the wooden shutters from the frame ) including cutting holes for hold fasts and making good disturbed surface with cement mortor or pcc after fixing new chowkats complete all as specified and directed by engineer in charge. 9 taking down chowkat or frame with shutters including fitting and fixtures area exc 1.5 sqm but not exc 4 sqm each ( without taking off the wooden shutters from the frame ) including cutting holes for hold fasts and making good disturbed surface with cement mortor or pcc after fixing new chowkats complete all as specified and directed by engineer in charge. 10 taking down and refixing door shutters of any description having area exc 1.00 sqm but not exc 2.00 sqm, each in the same opening including easing of door / window / cup board shutters for easy closing / opening incl tighening of hinges or changing the position of hinges adjustment of tower bolts, sliding bolts etc complete all as specified and directed by engineer in charge. 11 supply only integral water proofing compound ( isi marked ) complete all as specified and directed by engineer in charge. 12 m & l for plain cement concrete ( 1:3:6 ) type c 1 using 12.5mm graded stone aggregate as in filling of pressed steel frame, chowkats, hold fast blocks and other similar items etc complete all as specified and directed by engineer in charge. 13 m&l for brick work with sub class ‘b’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar ( 1:6 ) complete all as specified and directed by engineer in charge. 14 m&l for 30mm thick flush shutter solid core construction with block board core & ply wood face panels, commercial type on both faces complete all as specified and directed by engineer in charge. 15 s&f 35mm thick factory made glazed and skeleton shutters made of second class hard wood ( bonsum / hollock ) , open rebated and prepared to receive glass, gauze etc ( without sash bars ) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in ssr part i section 8 clause 8.24 ( a ) kiln seasoned and chemically pressure treated fixed to chowkat complete all as specified and directed by engineer in charge. 16 s&f factory made solid pvc door frame of size 50mm x 47mm made out of 5mm thick plain colour pvc sheet reinforced with ms square tube complete all as specified & shown in relevant drawing of item no. 08095 in mes schedule ( part ii ) and directed by engineer in charge 17 s&f 30mm thick factory made solid core pvc door shutter ( style ) consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour pvc sheet, c channel having pvc sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail; panelling of plain colour pvc sheet to be fitted in mild steel frame welded / sealed to the styles and rails with suitable pvc sheet beading and joined together with solvent cement, complete, all as specified & shown in relevant drawing of item no. 08080 in mes schedule ( part ii ) and directed by engineer in charge. 18 s&f 200 mm long aluminium anodized barrel tower bolts of extruded section ( isi marked ) complete all as specified and directed by engineer in charge. 19 s&f as in repair 200 mm long aluminium anodized barrel tower bolts of extruded section ( isi marked ) complete all as specified and directed by engineer in charge. 20 s&f as in repair 150 mm long aluminium anodized barrel tower bolts of extruded section ( isi marked ) complete all as specified and directed by engineer in charge. 21 s&f 100mm size mild steel butt hinges cold rolled medium weight ( isi marked ) complete all as specified & directed by engineer in charge. 22 s&f as in repair 100mm size mild steel butt hinges cold rolled medium weight ( isi marked ) complete all as specified & directed by engineer in charge. 23 s&f 100mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin, anodized type b 21 ( isi marked ) complete all as specified and directed by engineer in charge. 24 s&f as in repair 100mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin, anodized type b 21 ( isi marked ) complete all as specified and directed by engineer in charge. 25 s&f 300mm long aluminium alloy anodised sliding door bolts with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy ( isi marked ) complete all as specified & directed by engineer in charge. 26 s&f as in repair 300mm long aluminium alloy anodised sliding door bolts with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy ( isi marked ) complete all as specified & directed by engineer in charge. 27 s&f 150mm long extruded aluminium handles, anodised, fabricated type ( isi marked ) complete all as specified and directed by engineer in charge 28 s&f as in repair 150mm long extruded aluminium handles, anodised, fabricated type ( isi marked ) complete all as specified and directed by engineer in charge 29 s&f as in repair galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified and directed by engineer in charge. 30 s&f as in repairs powder coated mild steel drapery rod of 20 mm inner dia ( in lengths as directed ) of approved colour with & including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with pvc rawl plug & steel screws on walls / beam, including pvc curtain rings of matching colour @ 10cm c / c all as specified & as directed. 31 s&f as in repair mild steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate fixed to wooden frame or welded to steel frame making suitable cut out in wall and making good in cm 1:4 complete all as specified and directed by engineer in charge. 32 s&f as in repair pvc strips for wooden shutter for insects / dust proofing complete all as specified and directed by engineer in charge 33 m&l for mild steel roof trusses ( framed ) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc complete all as specified and directed by engineer in charge. 34 s&f factory made steel window with side hung shutters including projecting type hinges with steel handle, steel peg stay, fixing lugs etc complete with glazing bars including one shop coat of red oxide primer and cutting holes in brick wall built in cement mortar for inserting lugs and making good dismantled portion in cement mortor ( 1:3 ) or cement concrete ( 1:2:4 ) type b i complete all as specified & directed by engineer in charge 35 s&f factory made steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of zinc chromate primer and cutting holes in brick wall built in cement mortar for inserting lugs and making good dismantled portion in cement mortor ( 1:3 ) or cement concrete ( 1:2:4 ) type b i complete all as specified and directed by engineer in charge. 36 s&f pressed steel frames for door of size 125x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc made out of mild steel sheet of 1.25mm thickness complete all as specified and as directed. 37 s&f pressed steel frames for door of size 105x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc made out of mild steel sheet of 1.25mm thickness complete all as specified and as directed. 38 m & l for pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed by engineer in charge. 39 m & l for pre painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed by engineer in charge. 40 s&f as in repair 18 / 19 mm thick prelaminated particle board exterior grade, prelaminated both sides with decorative choice lamination fixed with screws to timber frame including 6mm thick teak wood lipping fixed with head less nails / screws for shelves / partition / pelmet boxes / kitchen cabinet / cupboard shutter complete all as specified and directed by engineer in charge. 41 s&f as in repair anodised aluminium snap grid frame work of size 605mm x 605mm for false ceiling including necessary notching. the snap grid shall consist of anodized aluminium main & cross tee of size 36.5mm x 25mm x 1.4mm weighing 0.24 kg / rm and 23.5mm x 26.4mm x1.40mm weighing 0.191kg / rm respectively. the main and cross tee shall be jointed at junction crossing with anodized aluminium angle bracket of size 15mm x 15mm x 1.5mm weighing 0.12kg / rm fixed with suitable ms bolts, nuts and washer. the snap grid ( main / cross tee section ) shall be supported at ends all along the wall with anodized aluminium angle of size 35mm x 25mm x 2mm weighing 0.36 kg / rm fixed to wall with suitable arrangement duly suspended with 3mm dia gi wire length as required @ 600mm c / c with adjustable device including plugging in brick / concrete work with steel raw plugs including making good all the disturebed portion complete all as specified and directed by engineer in charge. 42 m&l for 8mm thick non asbestos fibre cement building boards fixed or laid / inserted to timber / gi / aluminium framework with screws complete all as directed. & directed by engineer in charge. 43 m&l for non skid ceramic joint free coloured tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar ( 1:6 ) complete all as specified and directed by engineer in charge. 44 m&l for non skid ceramic joint free coloured tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar ( 1:4 ) complete all as specified and directed by engineer in charge. 45 m&l for glazed ceramic tiles ( coloured ) 450mm x 350mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar ( 1:4 ) including necesary cutting as per site requirment complete all as specified and directed by engineer in charge. 46 m&l for vitrified ceramic light shade ( as approved ) coloured tiles 10mm thick ( square / rectangular ) , polished, area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar ( 1:4 ) complete all as specified and directed by engineer in charge. 47 m&l for 15mm thick rendering in cement mortar ( 1:4 ) on brick walls / concrete surfaces mixed with water proofing compound as per manufacturer’s instructions including finishing the surfaces even and smooth without using extra cement complete all as specified and directed by engineer in charge.note : supply only water proofing compound shall be measured and paid for separately under respective item of boq. 48 m&l for 10mm thick rendering in cement mortar ( 1:6 ) on fair faced surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement complete all as specified and directed by engineer in charge. 49 m&l for rough cast finish plaster with a mixture consisting of crushed stone or fine gravel aggregate mixed with coarse sand and cement in the ratio of 1:1:1 over & including 12mm thick rendering in cement mortar 1:3 on fair faces of brick masonry or concrete surfaces of walls complete all as specified and directed by engineer in charge. 50 m&l for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed by engineer in charge. 51 m&l for preparation of newly plastered surface of walls & applying two coats of cement base paint of approved shade / tint and filling cement based putty in cracks complete all as specified and directed by engineer in charge. 52 m&l for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by engineer in charge. 53 m&l for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying two coat of white wash complete all as specified & directed by engineer in charge. 54 m&l for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, washing, rubbing down and stopping of distempered surface etc and applying two coat of distemper oil emulsion complete all as specified & directed by engineer in charge. 55 m&l for preparation of new plastered and unplastered surfaces of wall and applying two coats of oil bound distemper including alkali resistant priming preparatory to distempering complete all as specified & directed by engineer in charge. 56 m&l for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot mulds, moss and efflorescent, salts, filling of cracks etc and applying a coat of cement based paint complete all as specified & directed by engineer in charge. 57 m&l for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by engineer in charge. 58 m&l for preparation of old painted wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by engineer in charge. 59 m&l for preparation of old painted steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed by engineer in charge. 60 hacking out old broken glass any thickness, size, quality or description from wooden / metal frame and punching or drilling out old glazing pins / spring clips complete all as specified and directed by engineer in charge. 61 s&f 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing / new surfaces, complete all as specified and as directed. 62 s&f 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed by engineer in charge. 63 taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by engineer in charge. 64 s&f 15mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by engineer in charge. 65 taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by engineer in charge. 66 s&f 20 mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by engineer in charge. 67 s&f as in repair gun metal globe or gate valve 20mm bore with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by engineer in charge. 68 s&f as in repair ptmt swivel shower rose of any colour with swivel joints including shower arm of 15mm bore, 195 mm long with bend of 45 degree with flanges of ptmt ( complete minimum weight 80 grams ) complete all as specified & directed by engineer in charge. 69 s&f as in replacement 600mm long pvc connection suitable for 15 mm bore with ptmt nuts on both sides complete all as specified and directed by engineer in charge. 70 s&f as in repair rotational moulded polyethylene water storage tank isi marked ( cylindrical vertical three layered with closed top ) hoisted and fixed in position of capacity 500 litres including ball brass valve, high pressure with polythene float and flynut screwed for 20 mm dia gi pipe, 25mm bore gi washout pipe 15 cm long fitted with check nut, 20mm bore over flow pipe 1.50 metre long fitted with brass anti mosquito nest coupling at the end of over flow pipe & 15mm bore gi air vent pipe 1.30 metre long fitted with tee at the end of air vent pipe ( all gi pipes shall be medium grade ) complete all as specified and directed by engineer in charge. 71 all as per srl item no. 70 here in before but 1000 ltrs capacity 72 s&f as in repair 15 mm bore bib tap, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by engineer in charge. 73 s&f as in replacement ball valves, high pressure of ptmt with epoxy coated aluminum rod & high density plastic ball, screwed for iron pipe 15mm dia ( minimum weight 210 gms ) complete all as specified and as directed by engineer in charge. 74 s&f as in repair vitreous china wash basin white flat back of size 630 x 450mm including a pair of angle iron brackets, pvc connection of size 450mm, 15mm dia fancy type, cast copper alloy chromium plated pillar tap with capastan head screwed down high pressure with long screwed shank and fly nuts, 32mm dia full threaded ptmt waste coupling and 32mm dia waste pipe including cutting for and pinning in ends of brackets and 32mm dia high density polythelene ( hdpe ) pipes for pressure rating 6 kg / sqcm with all fittings such as sockets, bends, tapers, etc complete all as specified and directed by engineer in charge. 75 s&f as in repair vitreous china squatting pan orissa pattern, white of size 580x440mm with integral foot rests ( excluding flushing cistern and flush pipe ) including cast iron p or s trap, pcc filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by engineer in charge. 76 s&f as in repairs vitreous china wash down water closet pan ( pedestal pattern ) , white including connection to drain ( or outgoing pipe ) and to flushing pipe, anti sypohonage pipe etc. & with plastic wc seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device and jet spray complete all as specified & as directed by engineer in charge. 77 s&f as in repair 10 litre capacity pvc valveless symphonic action type low level flushing cistern ( isi marked ) including 32 mm dia pvc flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by engineer in charge. 78 s&f as in repair vitreous china half stall type, flat back urinal of size 390 x 375 x 590mm, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including ptmt grating and union for discharge pipe, chromium plated urinal spreader including waste pipe of polythelene of low or high density or pvc 32mm dia complete all as specified and directed by engineer in charge. 79 s&f as in repairs pvc waste pipe 32 to 40mm bore suitable for whb or sink complete all as specified and directed by engineer in charge. 80 s&f as in repair 600mm x 450mm beveled edge looking mirror of selected quality glass not less than 5.5mm thick, mounted on 6mm thick commercial plywood including pvc moulded framing and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by engineer in charge. 81 s&f as in repair 100mm bore cast iron sand cast soil, waste and vent pipe in any length with or without ears fixed with cement joints, laid in trenches or in floor complete all as specified & directed by engineer in charge.note : cost of excavation & earthwork is deemed to included to in the unit rate of this items nothing extra shall be paid on this account. 82 s&f 100mm bore cast iron bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) with oval access door complete all as specified and as directed by engineer in charge. 83 m&l as in repair 100mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete ( 1:2:4 ) type b 1 using 20mm graded stone aggregate complete all as specified and directed by engineer in charge. 84 s&f in replacement 110mm bore pvc ( swr ) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite number of clamps made out of flat iron 25x4mm complete all as specified and as directed by engineer in charge. 85 s&f in replacement 75mm bore pvc ( swr ) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite number of clamps made out of flat iron 25x4mm complete all as specified and as directed by engineer in charge. 86 s&f 110 mm bore pvc ( swr ) bends any radius jointed with adhesive complete all as specified and as directed by engineer in charge. 87 s&f 75 mm bore pvc ( swr ) bends any radius jointed with adhesive complete all as specified and as directed by engineer in charge. 88 s&f in repair stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm pvc pipe complete all as specified and directed by engineer in charge 89 s&f in repair stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm pvc pipe complete all as specified and directed by engineer in charge 90 taking down carefully or drawn out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, mcb, db, lamp, earth plug etc ( excluding ms sunken boxes ) and making good the disturbed surfaces of wall / ceiling complete all as specified and as directed by engineer in charge. note : taking down of serviceable fittings shall be measured and paid separately. 91 m&l for point wiring complete with 1.5 sqmm ( nominal cross sectional area ) frlsh pvc insulated multistandard unsheathed copper conductor cable with colour coding drawn in and including new pvc rigid conduit medium grade 20mm dia and suitable fittings, fixed onconcealed or above ceiling with accessories such as pipe hooks, elbows, junction box, terminated in new sunken box and covered with new 3mm thick bakelite plastic laminated sheet top cover fixed flush with wall using brass screws & cup washers including cutting chases in wall for conduits and making good the disturbed surfaces of wall and including 1.5 sqmm pvc insulated unsheathed multistandard copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point, fan point controlled by one way switch complete all as specified and directed by engineer in charge. 92 all as per serial item no. 91 here in before but for one 3 pin 5 amp socket outlet on the same board with other switches. 93 all as per serial item no. 91 here in before but for one 3 pin 5 amp socket outlet on independent board. 94 all as per serial item no. 91 here in before but for one bell or buzzer point controlled by by one push button on independent board. 95 all as per srl item no. 91 above, but wiring with cable of cross sectional area 2.5 sqmm ( nominal area ) multi stranded copper conductor frlsh, pvc unsheathed cable 1100 volts shade for one switch socket combination 6 pin, 5 / 15 amps on independent board including 2.5 sqmm pvc insulated multistandard unsheathed copper conductor wire as earth continuity to common earth dolly. 96 m&l for point wiring complete with 1.5 sqmm ( nominal cross sectional area ) frlsh pvc insulated multistandard unsheathed copper conductor cable with colour coding drawn in open conduit or existing concealed conduit in existing sunken box and covered with new 3mm thick bakelite plastic laminated sheet top cover fixed flush with wall using brass screws & cup washers including cutting chases in wall for conduits and making good the disturbed surfaces of wall and including 1.5 sqmm pvc insulated unshethed multistandard copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point, fan point, bell point controlled by one switch complete all as specifiedand directed by engineer in charge. 97 all as per serial item no. 96 here in before but for one 3 pin 5 amp socket outlet on the same board with other switches. 98 all as per serial item no. 96 here in before but for one 3 pin 5 amp socket outlet on independent board. 99 all as per serial item no. 96 here in before but for one light point controlled by two way switches. 100 all as per serial item no. 96 here in before but for one bell or buzzer point controlled by by one push button on independent board. 101 all as per srl item no. 96 above, but wiring with cable of cross sectional area 2.5 sqmm ( nominal area ) multi stranded copper conductor frlsh, pvc unsheathed cable 1100 volts shade for one switch socket combination 6 pin, 5 / 15 amps on independent board including 2.5 sqmm pvc insulated multistandard unsheathed copper conductor wire as earth continuity to common earth dolly. 102 s&f switch piano flush button 5 amps single pole, one way complete all as specified and directed by engineer in charge. 103 s&f switch piano flush button 5 amps single pole, two way complete all as specified and directed by engineer in charge. 104 s&f switch piano flush button 15 amps single pole, one way complete all as specified and directed by engineer in charge. 105 s&f socket outlet 3 / 5 pin, 5 amps 240 volts, flush type complete all as specified and directed by engineer in charge. 106 s&f socket outlet 3 / 5 pin, 15 amps 240 volts, flush type complete all as specified and directed by engineer in charge. 107 s&f bell push, flush type, 5 amp, 230 volts grade complete all as specified and directed by engineer in charge. 108 s&f lamp holder, insulated body with back plate etc complete all as specified and as directed by engineer in charge. 109 s&f ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by engineer in charge. 110 s&f electric bell ( ding dong ) , ac, 230 volts, single pole & connecting up complete all as specified and directed by engineer in charge. 111 s&f electronic fan regulator suitable for ceiling fan 1200mm / 1400mm sweep, socket size, rotary type complete all as specified and directed by engineer in charge. 112 s&f sheet metal plug & socket db, sp, with a two pin and earth plug with socket, 230 volts with & including one mcb sp ‘c’ curve 10 ka, 20 amps complete all as specified and directed by engineer in charge. 113 s&f energy efficient decorative ultra slim, prewired, maxoled batten for t 8 led retro lamp, polycarbonate body, 1.2m length, ultra bright, glass shell, glare free, wide angle single / double side connection retrofit led tube with g 13 lamp holder / patti 20 watt led light fitting ( day cool light ) including 20 watt led tube with all accessories prewired fixed on wall / hanging complete all as specified and as directed by engineer in charge. make : havells cat part no lhfxcenntn1w020 & lhlddcxcml8q020 / crompton cat part no dijb12lt8 20 & lgt8 16 865 2 or equivalent cat part no of makes mentioned in appendix a here in after. 114 s&f energy efficient decorative ultra slim prewired 9 / 10watt ( 600mm length ) led light fitting ( mirror light ) ( day cool light ) , surface and wall mounted led batten, extruded aluminium housing with polycarbonate diffuser & integrated electronic driver and all accessories fixed on wall / hanging complete all as specified and as directed by engineer in charge. make : havells cat part no lumilinebs9wled865s pcwh / syska cat part no ssk t5t 9w / crompton cat part no lctln 10 cdl or equivalent cat part no of makes mentioned in appendix a here in after. 115 s&f energy saving 9 / 10 watt environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge lit led luminaire comprising of high brightness leds, ip 65 protection fixed on wall complete all as specified and as directed by engineer in charge. make : havells cat part no hexaft10wled857ssy mbopc / syska cat part no ssk bh 9w / crompton cat part no lbhe 10 cdl or equivalent cat part no of makes mentioned in appendix a here in after. 116 supply and fixing led lamp minimum 3 star rated 10w led b 22 base complete all as specified and directed by engr in charge with following specifications ( a ) lumen system efficacy of lamp should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts ( c ) temp operating range : minus 10°c to plus 45°c ( d ) power factor : minimum 0.90 ( e ) cri: morethan80 117 supply, fixing and testing led street / security light fitting of 25 watt, 5700k 6500 k ( including led drive and internally prewired ) complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminum alloy. the luminaries shall be monolithic construction totally enclosed dust and water proof with ip 65 / 66 protection as per is 10322 1982 ( part i ) with latest amendments and input voltage range 140 300 v, ac, frequency 50 60 hz , p.f should be more than 0.9 with total harmonic distortion thd ( i ) less than 15% , cool white colour and lamp starting time should not be more than 10 second including 10 kv surge protection in built or external. driver should be constant current constant voltage driver. driver should have high voltage withstanding capacity upto 300 v, ac. driver should also have double phase protection, no load , open circuit and short circuit protection .led light fitting should be suitable for ambient temperature from 10 degree centigrade to 50 degree centigrade and humidity level 10% to 90 % rh. covers should be polycarbonate / toughened glass to ensure minimum ip 65 degree protection. cover should not degrade due to heating and ageing. the efficiency of led luminaries system shall be more than 100 lumens per watt and must be certified by the lm 79 test report and including connection for street light from pole box with 1.5 sqmm, 3 core pvc insulated stranded copper conductor frlsh cable, 1100 volts grade isi marked including addition / alteration in bracket ( if required ) for fixing light fitting complete all as specified and directed by engineer in charge. 118 notes for srl item no 117 : ( a ) tenderer shall submit test report of led street light fitting from government accredited test laboratory for lm 79 and lm 80 . ( b ) contractor has to furnish a replacement warranty of 05 years for led light fittings complete including lamps from the date of completion of ca. contractor shall obtain warranty from the manufacturer of product on their letter head and submit the same to deparment alonwith his letter head. the product will be replaced free of cost in the following case : ( i ) manfacturing defects ( ii ) failure due to mechanical and electrical impact. ( iii ) drop in lumen ( or lux at 1 m ) below 90% of clamied values of lumen ( or lux at 1 m ) of the led / luminaries. ( c ) all led light / luminare must meet the provision laid down in is 16101 , 16102 part i / ii , 16103 part i , 16104 , 16105 , 16106 , 16108 / 2012 and 15885 part ii / section 13. ( d ) scope of work shall include supply and fixing street light fittings on street light bracket fixed on poles, if street light fitting requires to fixed on existing street light bracket and any addition alterration required in bracket for fixing street light, in that case cost of additional / alteration is included in the unit rate of this item, which also includes needfult & p andrequired accessories such as 1.5 sqmm, 3 core pvc insulated stranded copper conductor cable for connection from pole box to light fitting etc complete including making connection, testing etc complete .no extra payment is admissible on this account. ( e ) light fittings shall be provided with 10 kv surge protection as mentioned in description of item. if 10 kv surge protection is not provided in light fitting for which cat part is mentioned in boq. contractor has to provide light fitting with 10 kv surge protection without any extra cost to department. ( f ) contractor shall write ca no on street light fitting with synthetic enamel paint which should be visible from ground level. cost of the same is included in the unit rate of this item nothing shall be extra paid on this account. 119 s&f as in repair flush mounting factory made spn db 4 way, 240 volt, double door, ip 43 protection, ik 09 with metal door with 100 amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by engineer in charge. 120 s&f as in repair flush mounting factory made spn db 8 way, 240 volt, single door, ip 43 protection, ik 09 with metal door with 100 amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by engineer in charge. 121 s&f as in repair flush mounting factory made tpn db 4 way, 415 volt, double door, ip 43 protection, ik 09 with metal door with 160 amps copper bus bar, with 02 neutral bar, 02 earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by engineer in charge. 122 s&f mcb 6 to 32 amps, single pole 240 volts, 10 ka, ‘c’ curve, complete all as specified and directed by engineer in charge. 123 s&f as in repair mcb 40 63 amps, single pole & neutral 240 volts, 10 ka, ‘c’ curve, complete all as specified and directed by engineer in charge. 124 s&f as in repair mcb 63 amps, triple pole & neutral 240 volts, 10 ka, ‘c’ curve, complete all as specified and directed by engineer in charge. 125 s&f as in replacement switch piano flush button 5 amps single pole, one way complete all as specified and directed by engineer in charge. 126 s&f as in replacement switch piano flush button 5 amps single pole, two way complete all as specified and directed by engineer in charge. 127 s&f as in replacement switch piano flush button 15 amps single pole, one way complete all as specified and directed by engineer in charge. 128 s&f as in replacement bell push, flush type, 5 amp, 230 volts grade complete all as specified and directed by engineer in charge. 129 s&f as in replacement socket outlet 3 / 5 pin, 5 amps 240 volts, flush type complete all as specified and directed by engineer in charge. 130 s&f as in replacement socket outlet 6 pin, 15 amps 240 volts, flush type complete all as specified and directed by engineer in charge. 131 s&f as in replacement lamp holder, insulated body with back plate etc complete all as specified and as directed by engineer in charge. 132 s&f as in replacement ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by engineer in charge. 133 s&f as in replacement switch socket combination 3 pin, 15 amps, 240 volts, flush type complete all as specified and directed by engineer in charge. 134 s&f as in replacement electric bell ( ding dong ) , ac, 230 volts, single pole & connecting up complete all as specified and directed by engineer in charge. 135 s&f as in replacement electronic fan regulator suitable for ceiling fan 1200mm / 1400mm sweep, socket size, rotary type complete all as specified and directed by engineer in charge. 136 s&f as in repair 3mm thick phenolic laminated sheet cover of size 8 x 5 for provn fixing of switch & socket & regulartor fixed with machine screws / washer complete all as specified and directed by engineer in charge. 137 s&f as in repair 3mm thick phenolic laminated sheet cover of size 9 x 5 for provn fixing of switch & socket & regulartor fixed with machine screws / washer complete all as specified and directed by engineer in charge. 138 s&f as in repair 3mm thick phenolic laminated sheet cover of size 9 x 11 for provn fixing of switch & socket & regulartor fixed with machine screws / washer complete all as specified and directed by engineer in charge. 139 s&f as in repair 3mm thick phenolic laminated sheet cover of size 11 x 5 for provn fixing of switch & socket & regulartor fixed with machine screws / washer complete all as specified and directed by engineer in charge. 140 s&f as in replacement energy efficient decorative ultra slim, prewired, maxoled batten for t 8 led retro lamp, polycarbonate body, 1.2m length, ultra bright, glass shell, glare free, wide angle single / double side connection retrofit led tube with g 13 lamp holder / patti 20 watt led light fitting ( day cool light ) including 20 watt led tube with all accessories prewired fixed on wall / hanging complete all as specified and as directed by engineer in charge. make : havells cat part no lhfxcenntn1w020 & lhlddcxcml8q020 / crompton cat part no dijb12lt8 20 & lgt8 16 865 2 or equivalent cat part no of makes mentioned in appendix a here in after. 141 s&f as in replacement energy efficient decorative ultra slim prewired 9 / 10watt ( 600mm length ) led light fitting ( mirror light ) ( day cool light ) , surface and wall mounted led batten, extruded aluminium housing with polycarbonate diffuser & integrated electronic driver and all accessories fixed on wall / hanging complete all as specified and as directed by engineer in charge. make : havells cat part no lumilinebs9wled865 spcwh / syska cat part no ssk t5t 9w / crompton cat part no lctln 10 cdl or equivalent in makes mentioned in appendix a here in after. 142 s&f as in replacement energy saving 9 / 10 watt environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge lit led luminaire comprising of high brightness leds, ip 65 protection fixed on wall complete all as specified and as directed by engineer in charge. make : havells cat part no hexaft10wled857ssy mbopc / syska cat part no ssk bh 9w / crompton cat part no lbhe 10 cdl or equivalent in makes mentioned in appendix a here in after. 143 supply and fixing in replacement led lamp minimum 3 star rated 12w led b 22 base complete all as specified and directed by engr in charge with following specifications ( a ) lumen system efficacy of lamp should be minimum 100 lumen per watt. ( b ) input voltage range : 140 to 270 volts ( c ) temp operating range : minus 10°c to plus 45°c ( d ) power factor : minimum 0.90 ( e ) cri: morethan80 144 s&f in replacement led post top 40 watt decorative circular design energy saving, ip 65 protection environmental freindly, long life aesthetically designed with symmetrical light distribution, cast aluminium body landscape luminaire with high power leds with polycarbonate type diffuser including two coat of black painting on existing post and cement work in base stand ( spigot housing with decorative opal acrylic diffusser and ip 65 protection with all accessories complete all as specified and as directed by engineer in charge. 145 s&f in replacement sub main wiring complete with 2 single core 6 sqmm ( nominal area ) multi stranded copper conductor pvc insulatedunsheathed cable frlsh drawn in and including heavy duty pvc conduit isi marked not less than 25mm dia concealed including single core multistranded copper conductor 6 sqmm size cable as earth continuity wire drawn in same conduit complete all as specified and directed by engineer in charge note :two runs of 6 sqmm single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with fittingsshall be measured as one length. 146 supply, fixing and testing as in replacement led bldg / security light fitting of 25 watt, 5700k 6500 k ( including led drive and internally prewired ) complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminum alloy. the luminaries shall be monolithic construction totally enclosed dust and water proof with ip 65 / 66 protection as per is 10322 1982 ( part i ) with latest amendments and input voltage range 140 300 v, ac, frequency 50 60 hz , p.f should be more than 0.9 with total harmonic distortion thd ( i ) less than 15%, cool white colour and lamp starting time should not be more than 10 second including 10 kv surge protection in built or external. driver should be constant current constant voltage driver. driver should have high voltage withstanding capacity upto 300 v, ac. driver should also have double phase protection, no load , open circuit and short circuit protection .led light fitting should be suitable for ambient temperature from 10 degree centigrade to 50 degree centigrade and humidity level 10% to 90 % rh. covers should be polycarbonate / toughened glass to ensure minimum ip 65 degree protection. cover should not degrade due to heating and ageing. the efficiency of led luminaries system shall be more than 100 lumens per watt and must be certified by the lm 79 test report and including connection for street light from pole box with 1.5 sqmm, 3 core pvc insulated stranded copper conductor frlsh cable, 1100 volts grade isi marked including addition / alteration in bracket ( if required ) for fixing light fitting complete all as specified and directed by engineer in charge. 147 notes for srl item no 145 : ( a ) tenderer shall submit test report of led street light fitting from government accredited test laboratory for lm 79 and lm 80 . ( b ) contractor has to furnish a replacement warranty of 05 years for led light fittings complete including lamps from the date of completion of ca. contractor shall obtain warranty from the manufacturer of product on their letter head and submit the same to deparment alonwith his letter head. the product will be replaced free of cost in the following case : ( i ) manfacturing defects ( ii ) failure due to mechanical and electrical impact. ( iii ) drop in lumen ( or lux at 1 m ) below 90% of clamied values of lumen ( or lux at 1 m ) of the led / luminaries. ( c ) all led light / luminare must meet the provision laid down in is 16101 , 16102 part i / ii , 16103 part i , 16104 , 16105 , 16106 , 16108 / 2012 and 15885 part ii / section 13. ( d ) scope of work shall include supply and fixing street light fittings on street light bracket fixed on poles, if street light fitting requires to fixed on existing street light bracket and any addition alterration required in bracket for fixing street light, in that case cost of additional / alteration is included in the unit rate of this item, which also includes needfult & p andrequired accessories such as 1.5 sqmm, 3 core pvc insulated stranded copper conductor cable for connection from pole box to light fitting etc complete including making connection, testing etc complete .no extra payment is admissible on this account. ( e ) light fittings shall be provided with 10 kv surge protection as mentioned in description of item. if 10 kv surge protection is not provided in light fitting for which cat part is mentioned in boq. contractor has to provide light fitting with 10 kv surge protection without any extra cost to department. ( f ) contractor shall write ca no on street light fitting with synthetic enamel paint which should be visible from ground level. cost of the same is included in the unit rate of this item nothing shall be extra paid on this account. 148 s&f as in repair capacitor of 3.15 mfd capacity, 230 volts including provision of insulation sleeves isi marked complete all as specified and directed by engineer in charge. 149 s&f as in replacement plug top 3 pin, 5 amp, 230 volt ac complete all as specified and as directed by engineer in charge. 150 s&f as in replacement plug top 3 pin, 15 amp, 230 volt ac complete all as specified and as directed by engineer in charge. 151 m&l for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to earth lead of gi wire 4 mm dia ( 8 swg ) by means of bolts, nuts and washers of the earth wire galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia and water pipe 20mm dia gi light grade top of pipe with funnel & wiremesh, and bottom connected to earth plate by slit and two bolts / nuts / washers, pcc chamber in cement concrete ( 1:2:4 ) type b 1 and 40mm thick rcc cover, excavation & earth work complete all as shown in electrical plate no. 3 of mes schedule part i of ssr 2009 including taking down old eathing complete all as specified and directed by engr in charge.notes : ( i ) cost of gi wire upto 7.5m is included in this item. ( ii ) pcc 1:2:4, excavation, earthwork is included in the quoted rate of this item. ( iii ) cost of gi tubing upto 7.5m is included in the quoted rate of this item. ( iv ) outer edge of earth pit chamber shall be 1.5 metre away from the outer edge of pcc chamber. ( v ) minimum weight of reinforcement for rcc cover shall be 1 kg. 152 supplying and fixing as in repair 1100 volts grade heavy duty cable pvc insulated solid aluminium conductor, served with inner sheathing of pvc tape and overall pvc sheathed in service connections in and including wherere required pvc conduit 20mm diaof 6 sqmm, one twin core cable flat or circular complete all as specified and directed by engineer in charge.notes : ( i ) excavation, earth work, sand cushioning, cable protection inlcuded in this item. nothing shall be extra paid on this account. ( ii ) road cutting / floor cutting / cutting holes etc in walls required for laying / fixing of cable etc shall be made good as per existing. nothing extra shall be admissible on this account. quoted rates shall deemed to be inclusive of the above provisions. 153 s&f as in repair switch socket combination 3 pin, 5 amps, 240 volts, flush type complete all as specified and directed by engineer in charge. note : a sum of rs. 68575 / will be deducted on account of credit for dismantled / demolished / taken down material. please refer details on srl page no. 28 to 30 ( schedule of credit ) of tender documents....