40784310
tender for special repair to bldg no p 152 ( jcos mess ) at mil station sri ganganagar.; 1 dismatiling brick tiles or terracing tiles, single layer on roofs complete all as specified and directed by engineer in charge. 2 demolition of mud in roofs, any thickness, including plastering and leeping ( whether full thickness removed or only a part thereof ) complete all as specified and directed by engineer in charge. 3 s&f heat resistance tiles ofsize 300x300x10mm thick on roof slab of any colour approved over and laid including 15mm thick in cm 1:4.techinical specification of roof tiles shall be as prer is 4457:2007 complete all as specified and directed by engineer in charge. 4 m&l for roof treatment to rcc roofas follows : ( a ) cleaning the roof surfaces thoroughly using wire brushes to remove sharp projections, cleaning joints, washing, drying and removing all dirt / dust to receive concrete padding / plaster etc complete. ( b ) providing 15 mm thick screed bed or bedding layer in cement mortar ( 1:4 ) with wpc , finished even and smooth without using extra cement. ( c ) providing one coat of approved bituminous primer @ 100 gms per sqm, over dried plastered surface. ( d ) laying 3 mm thick app based polymeric membrane, ( mineral finish ) minimum weighing 3 kg / sqm reinforced withnon woven polyster fabric ( weight not less than 150 gms / sqm ) by torch application. the overlapping while torching shall be 75 mm on longitudinal direction and 100 mm on the transverse direction complete all as specified and directed by engineer in charge.makes: stp, dr fixit, sikka, torch tar notes: ( i ) all joints and change in directions should be covered with cement mortar ( 1:3 ) mixed with sbr latex @ 200 ml / bag of cement / as per site requirement and cured well before laying membrane by torching. ( ii ) all angles and abuttments should be sealed well with extra care to ensure full bondage. ( iii ) water proofing treatment shall be got carried out by approved authorised applicator of manufacturer only.the name of firm shall be got approved from ge before carrying out the work. ( iv ) the independent testing of membrane for technical parameters given in particular specificationsshall be carried out from govt approved labs having fascilities for testing of membrane. ( v ) the guarantee of treatment shall be for minimum 10 yearsreckoned from date of completion of whole work complete all as specified and directed by engineer in charge. 5 m&l pcc 1:2:4, type b1 using 20 mm graded stone aggregate as in roof kerbs / benching / coved fillets etc rounded or chamfered on edges, complete all as specified and directed by engineer in charge. 6 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , and rubbish off the premises complete all as specified and directed by engineer in charge.. 7 m&l 300x600 x7 mm thick glazed ceramic coloured tiles as in vertical sufaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles and incliding 10mm thick backing coat in cm 1:4. complete all as specified and directed by engineer in charge. 8 m&l non skid ceramic coloured tiles 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles and incliding 15mm thick screed in cm 1:6 complete all as specified and directed by engineer in charge. 9 m&l light shade vitrified ceramic tiles 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over screed bed or bedding layer of mortar 15 mm thick in cm 1:6 for laying floor finishes complete all as specified and directed by engineer in charge. 10 m & lmachine cut kota stone slab flooring 18 20mm thick ( minimum size 55 cms x 55 cms ) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing including 15mm thick of screed bed in cm 1:6.complete all as specified and directed by engineer in charge. 11 m & l machine cut kota stone slabs as in vertical surfces such as risers of steps 18 20mm thickover cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing also moulding edgesincluding 10mm thick of backing coat in cm 1:4, complete all as specified and directed by engineer in charge. 12 m&l granite ( of any type ) work18 to 20 mm thick ( table rubbedand polished ) in steps, jambs, pillars, window cills, cooking platforms, hand wash platform and like laid over and including 12 mm thick cement mortar in cm 1:4including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by engineer in charge. 13 demolition of reinforced cement concrete of any description and in any position not other wise specifically provided for ( reinforcement cut as required to facilitate demolition ) complete all as specified and directed by engineer in charge. 14 m&l providingreinfoced cement concrete ( nominal mix ) in cement concrete 1:2:4 type b1 ( 20mm graded aggregate ) as chajjas, lintel, plinth beametcand similar workcomplete all as specified and directed by engineer in charge. ( note : the rate quoted shall be deemed to include use and waste of necessary form work ) 15 m&l tmt bar 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9 mm dia complete all as specified and directed by engineer in charge. 16 m&l for providing precast rcc jallies ( cement concrete type b0 1:2:4 12.5mm gragded aggregate ) louvres and jallies, 40 mm thick ( measured solid ) , including allmouldings & set in cm 1:4 complete all as specified and directed by engineer in charge. 17 demolition concrete in ground floors and pavings n exc 15cm thickness ( below or above ground level ) complete all as specified and directed by engineer in charge. 18 m&l75 mm thick cement concrete type d2, 1:4:8 ( using 40mm graded stone aggregate ) filling sub base as in floors, paving, sub floor etc finished even and smoothcomplete all as specified and directed by engineer in charge. 19 m&l 25mm thick cement concrete flooring type b0, 1:2:4 using 12.5 mm graded aggregate finished even and fair complete all as specified and directed by engineer in charge. 20 m&l for sand filling ( 25mm thick ) under floors or in foundations including watering and consolidation complete all as specified and directed by engineer in charge. 21 m&l machine pressed precastrubber moulded concretecoloured interlocking paver block any shape and size confirming to is 15468 2006 of 60 mm thickness with grey cement and pigmentm 35 grade 20mm graded stone aggregate ) complete all as specified and directed by engineer in charge. 22 m&l providing precast cement concrete in pcc ( 1:2:4 ) type b 1 with 20 mm graded aggregate for kerb stone and similar works with plain fair finishes including chamfers, weatherings, throat ing etc. and setting in mortar ( 1:4 ) complete with joints to match complete all as specified and directed by engineer in charge. 23 m & l for 75mm thick cement concrete type c 1, 1:3:6 using 20mm graged aggregate as in plinth protection complete all as specified and directed by engineer in charge. 24 m & l for 40mm thick cement concrete type b 1, 1:2:4 using 20mm graged aggregate as in flooring , finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by engineer in charge. 25 dismantling of brick work built in cement mortar of any description complete all as specified and directed by engineer in charge. 26 m&l for brick work with sub class b bricks ( old size ) straight or curved on plan exc 6 m mean radius built in cm 1:6complete all as specified and directed by engineer in charge. 27 m&l for brick work with sub class b bricks straight or curved on plan exc 6 m mean radius built in cm 1:6 but except bricks complete all as specified and directed by engineer in charge. 28 taking down cement plaster any description including raking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed by engineer in charge. 29 m&l rendering 15 mm thick in cm ( 1:6 ) finished even and smooth without using extra cement as on brick work surfaces complete all as specified and directed by engineer in charge. 30 m&l 15mm thick rendering in cm 1:4 to brick / concrete wall surfaces finishedeven & smooth w / o using extra cement. complete all as specified and directed by engineer in charge. note: work is to be carried out upto 10 mtr height. 31 m&l 5 mm thick cement plaster in cement mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed by engineer in charge. 32 m&l for preparation ofnewly plastered surface of wall any description and applying twocoats of oil emulsion distemper over & including 3 mm thick wall putty over a coat of chalk whiting layer on plastered surfaces preparatory to distempering complete all as specified and directed by engineer in charge. 33 m & l preparation of new plastered surfaces of wall and applying two coats of cement base paint over & including 3 mm thick wall putty over one coat of alkali resistantprimer complete all as specified and directed by engineer in charge. 34 m & l for three coats of white washing on new plastered surfaces of on ceiling surface including preparation of surface complete all as specified and directed by engineer in charge. 35 m&l for preparation of old surface including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and removing all dirt and dust by watering making surface even and smooth and then applying two coats of cement base paint over over & including 3 mm thick wall putty well prepared old decorated plastered surface etc complete all as specified and directed by engineer in charge. 36 m & l for preparation of old decorated wall surfacesby brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spotsand then applying two coats of oil bounddistemper over & including 3 mm thick wall puttycomplete all as specified and directed by engineer in charge. 37 m & l forold decorated ceiling surfacesby brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spotsandthen applyingtwo coats of white washcomplete all as specified and directed by engineer in charge. 38 taking downsteel window / ventilators complete all as specified and directed by engineer in charge. 39 taking down chowkats or frames ( without taking off shutters from the frame ) not exceeding 1.5 sqm each complete all as specified and directed by engineer in charge. 40 taking down shutters of any description exc 1 sqm but n exc 2 sqm each complete all as specified and directed by engineer in charge. 41 taking down chowkats or frames with shutters ( without taking off shutters from the frame ) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified and directed by engineer in charge. 42 taking down shutters of any material and description exc 1 sqm but n exc 2 sqm each and refixing in same opening after resecuring easing duly completed repair work in all respects etc.complete all as specified and directed by engineer in charge. 43 taking down shutters of any material and description n exc 1 sqmeach and refixing in same opening after resecuring easing duly completed repair work in all respects etc.complete all as specified and directed by engineer in charge. 44 s&f steel windows with side hung shutters includinghinges with steel handle and steel peg stay, complete with glazing bars, devetailed or welded complete all as specified and directed by engineer in charge. 45 s&f 10mm dia m. s round guard bars for steel windows & including welding complete all as specified and directed by engineer in charge. 46 s&f ms falt iron 25 x 6mm as in hold fast confirming to fe 290 gde e 165 complete all as specified and directed by engineer in charge. 47 m&l for cutting holes in brick ( n.exc half brick ) walls in cement mortar forinserting holdfasts andmaking gooddismantled portion incement mortar 1:3 or cement concrete 1:2:4type b 1 complete all as specified and directed by engineer in charge. 48 s&f framed brackets of angles or tee with web and flange cut to shape, drilled and counter shunk for screw, including bending and welding angles asnecessary gusset plates riveting rails, braces, running rails and guides and hanging; also fastening and fixing complete conforming to fe 290 ( grade 165 ) complete all as specified and directed by engineer in charge. 49 s & f factory made pressed steel frames of frame size 125 x 60mmfor doors with one or more rebatesincluding necessary fixing lugs, hold fasts, hinges, lock strike plate, etc., complete all as specified and directed by engineer in charge. ( note : mild steel sheet shall be 1.25mm thick ) 50 s & f factory made pressed steel frames of frame size 105 x 60mmfor doors with one or more rebatesincluding necessary fixing lugs, hold fasts, hinges, lock strike plate, etc., complete all as specified and directed by engineer in charge. ( note : mild steel sheet shall be 1.25mm thick ) 51 m&l for providing cement concrete ( 1:3:6 ) type c1 using 20 mm gradded stone aggregate for filling in pressed steel frames and other similar items complete all as specified and directed by engineer in charge. 52 s & f 2nd class hard wood plain solid straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed by engineer in charge. 53 s & f 35mm thick factory made shutter, plain, framed, panelled shutters factory made ( any number of panels ) , with panels of timber flat on both sides ( feather edged ) , or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed by engineer in charge. 54 s & f factory made second class hard wood glazed and skeleton door, window shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares with plain, chamfered or rounded mitred and rebated sash bars any number& fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in ssr part i, section 8 clause 8.24 ( a ) complete all as specified and directed by engineer in charge. 55 s&f 18 / 19mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screws to timber frame work, including piano hinges, sliding channels and wheels with magneting cather / locking arrangements and beading etccomplete all as specified and directed by engineer in charge. 56 s & f continuous ( piano ) hinges, ( width of flap 40mm when open ) mild steel, bright finish or electrogalvanised complete all as specified and directed by engineer in charge. 57 s&f in repair aluminium 150 mm long hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed by engineer in charge. 58 s&ffiber glass reinforced plastic ( frp ) door frames of three legged of cross section 90mmx45mm having single rebate of 32mmx15mm to receive shutter of 30mm thickness. the laminate door frame molded with fire retardant grade unsaturated polyster resin and chopped mat. door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. the frame shall be covered with fiberglass from all sides. m s stay shall be provided at the bottom to steady the frame complete all as specified and directed by engineer in charge. 59 s&f factory made 30mm thick fiber glass reinforced plastic ( frp paneled doorshitter ofrequired colour and approved brand and manufacture made with fire retardant grade unsaturated polyster resin. moulded to 3mm thick frp laminate for forming places for fixing of fittings cast monolithically with 5mm thick frp laminate for panels and conforming to is 14856 2000 complete all as specified and directed by engineer in charge. 60 s&f 100 mmbutt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type c 21 complete all as specified and directed by engineer in charge. 61 s&f 125 mmbutt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type c 21 complete all as specified and directed by engineer in charge. 62 s&f 75 mmbutt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type c 21 complete all as specified and directed by engineer in charge. 63 s&f 125 aluminium anodised barrel tower bolts of extruded sction and fixedcomplete all as specified and directed by engineer in charge. 64 s&f aluminium handle cast type anodised, 150mm long complete all as specified and directed by engineer in charge. 65 s&f 300mm long aluminium alloy anodised sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed by engineer in charge. 66 s&f aluminium anodised barrel tower bolts of extruded section 150mm long complete all as specified and directed by engineer in charge. 67 s&f 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by engineer in charge. 68 s&f in repairs 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by engineer in charge. 69 s&f stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by engineer in charge. 70 s&f in repair stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by engineer in charge. 71 s & f for floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140mm anodised, with hard drawn steel spring, complete all as specified and directed by engineer in charge. 72 hacking out old broken glass ( any thickness, size, quality or description ) from wooden frames or stone, concrete or brick sorrounds, glazed with oil putty or fixed with beads complete all as specified and directed by engineer in charge. 73 s&f 4mm thick sheet glass ordinary quality and glazing with oil putty in squaren. exc 0.5 sqm in each plane complete all as specified and directed by engineer in charge. 74 s&f 4mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in suqares n.exc 0.5 sqm in each pane complete all as specified and directed by engineer in charge. 75 s&faluminium frame for doors, window, ventilatorswith one or more rebates including joining cleat for fixing including sliding chennals etc complete with powder coating on aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners . aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required all complete as per the direction of engineer in charge 76 s&f powder coated aluminium door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 nos in each door, hinges, powder coated aluminum snap beading screws etc. including sliding channel, wheel, cleats with whole arrangement complete all as specified and directed by engineer in charge 77 s&faluminiumwindowsand ventilator shutters, side hung typewithout sash bars, aluminium saction weighing 0.55 kg / m including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fitting such as aluminiumpeg stay 150mm long ( 1no ) , powder coated aluminiumhinges type b 21 100 mm long ( 2no ) , suitable powder coatedaluminium handle ( 1no ) , and powder coated aluminium self closing tower bolt 75mm long ( 1no ) complete all as specified and directed by engineer in charge. 78 s&f powder coated aluminium grills to aluminium windows including all necessary fixing arrangments of size 50 mm x 5 mm thick complete all as specified and as directed by engineer in charge.note: design shall be approvedby engineer in charge. note : minimum thickness of powder coating shall not be less than 50 micron. 79 s & f for 5.5mm thick sheet glass ( tinted ) , selected quality and glazing with necessory arrangement in square exc 0.5 sq. m in each pane complete all as specified and directed by engineer in charge. 80 m&l for preparation of old painted wooden surfaces of any description over 10cm width or girth not otherwise described and applying onecoat of synthetic enamel paint complete all as specified and directed by engineer in charge.. 81 m&l for preparation of new wooden and wood base surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primercomplete all as specified and directed by engineer in charge. 82 m&l for preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described and applying one coats of synthetic enamel paint complete all as specified and directed by engineer in charge. 83 m&l for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed by engineer in charge. 84 s&f in repairs white vitreous china squatting pan orissa pattern of size 580mm x 440 mm, with integral foot rest and p or s trap connection to trap and to flushing pipe front or back inlet including, trap complete all as specified and directed by engineer in charge. 85 s&f in repair vitreous china wash down water closet pan ( pedestal pattern ) , white complete, including white seat cover with hinging arrangement, ( excluding fixing bolts, flushing cistern and flush pipe complete all as specified and directed by engineer in charge. 86 s&f in repairs 10 ltr capacity low level pvc valveless, syphonic action type flushing cistern ( dual system ) , white, with inlet, ball valve, flush pipe, pvc connection 15 mm dia and 450 mm long float and handle including bracket. complete all as specified and directed by engineer in charge. 87 s&f in repair cp toilet paper holdercomplete all as specified and directed by engineer in charge. 88 s&f in repair cp soap dish complete all as specified and directed by engineer in charge. 89 s & f in repairs 20 mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by engineer in charge. 90 s & f in repair 15 mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by engineer in charge. 91 s&f in repairs chromium plated stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed by engineer in charge. 92 s&f in repairs chromium plated angle stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed by engineer in charge. 93 s&f in repair concealed chromium plated angle stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed by engineer in charge. 94 s&f in repairs chromium plated 15mm bib taps cast copper alloy, chromium platedfency type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by engineer in charge. 95 s&f in repairs pvc connection 15mm size with ptmt nuts of length 450mm long complete all as specified and directed by engineer in charge. 96 s&f in repairs pvc connection 15mm size with ptmt nuts of length 600 m long complete all as specified and directed by engineer in charge. 97 s&f cp gratings 100 mm diafixed in repairs. ( minimumweight25 gms ) complete all as specified and directed by engineer in charge. 98 taking up or down gi steel water tubing 15mm bore and connections including fittings from floor / walls / ceiling complete all as specified and directed by engineer in charge. 99 taking up or down gi steel water tubing 20mm bore and connections including fittings from floor / walls / centrings complete all as specified and directed by engineer in charge. 100 s & f galvanised steel water tubing 15 mm bore medium grade with all fittings concealed including cutting chases to brick wall / ceiling or laying in floors and making good complete all as specified and directed by engineer in charge. 101 fixing only tubes, of 15mm bore any grade, ( medium ) to walls and ceilings or laying in floors complete all as specified and directed by engineer in charge. 102 s & f gi steel water tubing 20mm bore medium grade with all fittings and fixed complete to walls ceiling or laid in floors complete all as specified and directed by engineer in charge. 103 fixing only tubes, of 20 mm bore any grade, ( medium ) to walls and ceilings or laying in floors complete all as specified and directed by engineer in charge. 104 dismantling water tanks any type exc. 250 ltr but nexc 500 ltr complete all as specified and directed by engineer in charge. 105 s & f rotational moulded polythylene water storage tank ( cylindrical vertical with closed top ) hoisted and fixed in position all as specified in ssr part i ( 1000 ltrs ) capacity. complete all as specified and directed by engineer in charge. ( note : pvc tanks shall be isi marked & having two layers ) 106 supply and fixing ball valves high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed for bore dia of pipe 20mm.complete all as specified and directed by engineer in charge. 107 dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required.complete all as specified and directed by engineer in charge. 108 s&f 100mm bore sand cast, cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or fixed to wall complete all as specified and directed by engineer in charge 109 s&f 75mm bore sand cast, cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or fixed to wall complete all as specified and directed by engineer in charge 110 s&fcast iron 100mm bore cast iron bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) complete all as specified and directed by engineer in charge. 111 s&fcast iron 75mm bore cast iron bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) complete all as specified and directed by engineer in charge. 112 s&f cast iron 100 mm bore branch pieces, single ( equal or unequal ) , ordinary or inverted ( spigot or socket type ) or with parallel branches complete all as specified and directed by engineer in charge. 113 s&f cast iron 75 mm bore branch pieces, single ( equal or unequal ) , ordinary or inverted ( spigot or socket type ) or with parallel branches complete all as specified and directed by engineer in charge. 114 s&fcast iron100 mmbore branch pieces, double ( equal or unequal ) , ordinary or inverted ( spigot or socket type ) or with parallel branches complete all as specified and directed by engineer in charge. 115 s&f cast iron 75 mm bore branch pieces, double ( equal or unequal ) , ordinary or inverted ( spigot or socket type ) or with parallel branchescomplete all as specified and directed by engineer in charge. 116 s& f 100 mm bore cast iron sockets ( double ) collars complete all as specified and directed by engineer in charge. 117 s& f 75 mm bore cast iron sockets ( double ) collars complete all as specified and directed by engineer in charge. 118 s&f 100 mm cast iron traps ‘p’ or ‘s’complete all as specified and directed by engineer in charge. 119 s&f100 mm cast iron cowls complete all as specified and directed by engineer in charge. 120 taking down eaves gutters and rainwater pipes, pvc ( swr ) pipes ( any size or pattern ) including all fittings heads , shoes, bends, and removal to store complete all as specified and directed by engineer in charge. 121 s&f 110 mm borediapvc ( swr ) pipes single socketed in any length with rubber ring joints, fixed to walls includingnecessary scaffolding upto the height of buildingfrom ground level complete all as specified and directed by engineer in charge. 122 s&f 110 mm dia pvc ( swr ) bend with oval access door complete all as specified and directed by engineer in charge. 123 supply and fixing drapery curtain rod 25mm dia, fancy type, fabricated out of stainless steel steel sheet not less than 20 guage, including brackets and pair of decorated end knobs ( finials ) , stop roller etc, pretreated powder coated natural color completeall as specified & directed by engineer in charge. 124 s&f in rep aluminium door closer hydraulically regulated, designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by engineer in charge. 125 s&f in replacement double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by engineer in charge. 126 s & f in repair stainless steel sink with drainage board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mmcomplete all as specified and directed by engineer in charge. 127 dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by engineer in charge. 128 m & l for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening and fixing complete conforming to fe 290 ( grade 165 ) complete all as specified and directed by engineer in charge. 129 m & l framed work as in doors or gates of angle or other section with gusset plates, for stainless steel framed work as in multipurpose vegitable rack, ration rack, utensils racks, plate rack ofgde 304 ordoors or gates of angle or other section with gusset plates, rails, braces, including ss wire guage arragements in sides etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening and fixing, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening and fixing complete complete conforming complete all as specified and directed by engineer in charge. 130 excavating post holes ( or similar holes ) each n.exc. 0.5 cum getting out returning filling, in and ramming with earth around in layers not exc. 25 cm includingwatering and removing surplus soil to a distance n.exc. 50m and making good surface in soft loose soil complete all as specified and directedbyendineer in charge. 131 m&l pcc 1:3:6 ( 40mm graded stone aggregate ) type c2, in foundation of posts and strutscomplete all as specified and directedbyendineer in charge. 132 s&f pre painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directedbyendineer in charge. 133 s&f pre painted galvalume aluminium zinc coating gi based plain steel sheet 0.50mm thick of any colour having tensile strength of 550mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directedbyendineer in charge. 134 s&f 0.56 mm thickplain, aluminium sheeting, alloy 31000 h4 for crumple / expansion joints, ridges, hips, valley gutter, drip, and straight flashing ( length and girth as fixed ) fixed with self tapping screws complete all as specified and directedbyendineer in charge. 135 s & f for steel work in tubular trusses , channels , purlines, crange gantries, rails including special shaped washer, platesnuts and bolts, gusset plates, including necessary drillingetc. complete using erw or induction butt welded tubes conforming to i. s.1161 1979 grade st. 240 complete all as specified and directedbyendineer in charge. 136 s & f for flat ironfor wind ties, plates ( plain or chequered ) channels, posts, square cut or notched ( ordinary and counter sunk ) forming holesetcfe 410 w ( gde e 250 ) quality a complete all as specified and directedbyendineer in charge. 137 s&f mild steel screw bolts ( machine made ) with hexagonal or square head at one end, and screwed the other, or screwed bothend to be fitted with washer and one hexagonal / square nut not exceeding 5cm long and dia of neck 11 to 15mm complete all as specified and directed by engineer in charge. 138 s&f for dwcpe ( s n 8 ) drain pipe 150mm internal dia confirming to is 16098 part ii 2013 laid in trenches on moorum bed to required slope including all accessories / fitting complete all as specified and directed by engineer in charge.note: moorum shall be paid separately. 139 excavation in trenches, n exc 1.5m wide and n exc 1.5 m depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and directed by engineer in charge. 140 returning, filling in, including spreading, levelling , watering and well ramming in layers not exc 25 cm.in soft / loose soil complete all as specified and directed by engineer in charge. 141 removing excavated material n exc. 50 mtr and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by engineer in charge. 142 m & l for pcc ( 1:4:8 ) type d2 ( 40mm graded stone aggregate ) as in foundation lean concrete complete all as specified and directed by engineer in charge. 143 m&l for pcc 1:3:6 type c 2 ( 40mm graded stone agg. ) concrete in surface channels and drains complete all as specified and directed by engineer in charge. 144 m&l for brickwork withsub class `b bricks, straight or curved on plan exc 6m meanradius, built in cm 1:4 in half brick thick wall / on edge wall complete all as specified and directed by engineer in charge. 145 taking down carefully copper / aluminium point wiring ( light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in cm 1:3 etc complete all as specified and directed by engineer in charge. 146 dismantling and taking down fluorescent / ledtube light / wall light / ceiling light single / bulk head / tube light / suspension light / mirror light double of any wattage or size street light fittings for repair / refixing purpose all as specified and directed by engr in charge. 147 fixing only led lights fitting 1x 20 / 25w, 220v, led tube light / security light / bulk head / mirror light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 148 m & lfor concealed conduit point wiring complete for light / fan on independent / combine boardwith cable 1.5 sqmm ( nominal area ) frlshpvc insulated multistranded unsheathed copper conductor, drawn in and includingpvc concealed conduitpipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , aftercutting in wall chasing for conduits and sinkings for sunkencast iron / pressed steelterminal boxes suitable lengthandthickness for mounting, switches, sockets, fan regulatorwith 3 mm thick plastic laminated sheet cover fixedwith brass screwed and cup washers, dulygrouting and painted with red oxide metal primer and making the gooddisturbed surfaces of wallin cm 1:3 with white wash or existing colour including provision ofcontinuousearth continuity conductoralong with point wiring of 1.5 sqmm copper pvc insulated cable for one light / fan point controlled by one switchand connected to commonearth dolly, complete all as specified anddirecedby the engineer in charge. 149 all as per srl item no 148 here in before but for one switch socket combination5 / 6 amp on independent board complete all as specified and directed by engineer in charge. 150 all as per srl item no 148 here in before but for one three pin socket outlet 5 amp on same board with other switches complete all as specified and directed by engineer in charge. 151 all as per srl item no. 148 here in before but for one switch socket combinationt 6 pin 5 / 15 amps on independent board with copper conductor 2.5 sqmm complete all as specified and directed by engineer in charge. 152 s & f switch piano flush type 5 / 6 amps single pole one way complete all as specified and directed by engineer in charge. 153 s & f switch socket combination 5 pin, type 5 / 6 amps flush type complete all as specified and directed by engineer in charge. 154 s & f switch socket combination 6 pin, 5 / 16 amps flush type complete all as specified and directed by engineer in charge. 155 s & f socket outlet 5 pin 5 amps flush type complete all as specified and directed by engineer in charge. 156 s & f ceiling rose surface bakelitethree terminals complete all as specified and directed by engineer in charge. 157 s & f in repair compact & decorative energy efficient led mirror light fitting with antiglare diffuser and decorative end caps suitable for 1x10 watt fitting 2 ft version including led lamp 10 watt complete all as specified and directed by engineer in charge. 158 s & f in replacement of existing light fitting withled batten with aliminium housing andintegrated electronic driver, 20 watt having input voltage ac90 300v, 50 hz , 6500k, and all other accessories including connection with flexiblecable copper conductortwin coreof size 23 / .2 mm upto ceiling rose / connector complete all as specified and directed by engineer in charge. 159 s & f angle holder insulated body with back plate for conduit fittings complete all as specified and directed by engineer in charge. 160 s&f led lamp 9w for angle holder complete all as specified and directed by engineer in charge. 161 s & fin replacement water tight bulk head fitting, comprision of connector , weather proof enamelled gallery , glass well, and including 10 watt led lamp all as specified and directed by engineer in charge. 162 s&f in replacementmcb protected socket 25amps in renewal with plastic box and plug topvertical din rail mount type suitable to operate at 240v current rating range 25a , 50hz 1ph, complied is specification 13032 & 8623 complete all as specified and directed by engineer in charge. 163 s&fin replacementround recess mounted led edge lit slim downlight 12 watt ( 6500k ) with opal diffuser and separate electronic driver die cat aluminum housing fineshed in premium white powder coating efficacy 100lm / w complete all as specified and directed by engineer in charge. 164 s&f decorative, wall mounting, made of polycorbonate suitable for 9 w led lamp, b22 base complete all as specified and directed by engineer in charge. 165 s & f stepped type, single socket fan regulator for ceiling fan 1200 / 1400mm sweep complete all as specified and directed by engineer in charge. 166 s & f in replacement of sub main wiring with two single core cables pvc insulated and un sheathed 6 sqmm ( nominal area ) frlsh multistranded copper conductor drawn in concealedpvc conduict dia 25mm “medium quality” conduit including 6.00 sq mm ( nominal area ) copper cableas earthcontinuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and coversincluding necessary connections, pvcflexible pipes are used in pannel board while connecting the cablecomplete all as specified and directed by engineer in charge. ( note : pvc cable and pvc conduit shall be isi marked ) 167 s & f in replacement of sub main wiring with two single core cables pvc insulated and un sheathed 4 sqmm ( nominal area ) frlsh stranded copper conductor drawn in concealedpvc conduict dia 25mm “medium quality” conduit including 4.00 sq mm ( nominal area ) copper cableas earthcontinuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and coversincluding necessary connections, pvcflexible pipes are used in pannel board while connecting the cablecomplete all as specified and directed by engineer in charge. ( note : pvc cable and pvc conduit shall be isi marked ) 168 s & f in repairs sheet metal enclosure for double door db made out of crca mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted sp & n 8 ways, 240 volts, isi marked, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation mcbs and isolators etc complete all as specified and directed by engineer in charge. 169 s & f in repairs sheet metal enclosure for double door db made out of crca mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted sp & n 12 ways, 240 volts, isi marked, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation mcbs and isolators etc complete all as specified and directed by engineer in charge. 170 s&f in repairs mccb tp&n 63 amps with breaking capcity 16ka , fixed tm and 415 volts ac supply isi marked complete all as specified and directed by engineer in charge. 171 s & f in repairs mcb ‘c’ series type suitable for 240 volts, ac supply5 to 40 amps, s p & n with over load and short circuit protection and rupturing capacity not less than 10ka complete all as specified and directed by engineer in charge. 172 s & f in repairsmcb ‘b’ series type suitable for 240 volts, ac supply5 to 40 amps , single pole with over load and short circuit protection and rupturing capacity not less than 10ka complete all as specified and directed by engineer in charge. 173 m & l for earthing complete with gi earth plate electrode 60 cm x 60 cm x 6 mmthick burried directly in ground ( earth pit not less than 2.25 mtr deep below ground level ) with top edge of plate not less than 1.5 mtr below ground level , connecting to gi earth lead 4 mm dia gi earth wire , by means of bolts, nuts and washers of giand protection by provisionof gi medium grade pipe 15 mm bore including provision of concrete pit in pcc ( 1:2:4 ) type b1 using 20 mm grade stone aggregate with 40 mm thick cover of rcc ( 1:2:4 ) reinforced with xpm ( weight not less than 4kgs / sqmm ) and frame of angle iron 25mmx25mmx6mm with lugs 02 nos and with 6 mm dia ms bar handle made to shape , gi light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmx 8 mm fi with fixing arrangement , funnel, wire mesh and earth work inhard dense soil , returning filling in and removal of surplus soil to a distance not exceeding50 mtrs all as per electric plate no.3 of ssr part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed by engr in charge 174 s&fin replacement security light fitting led type 25 watt with all necessary acessories, clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 hz ac & supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23 / 0.0076 complete all as specified and directed by engineer in charge 175 s&f in repairs sheet metal enclouser for doble door vertical dbs made out of crca mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting vtpn 4 way 415 voltisi marked 250amps busbar stove enameled dust and vermin proof, ip:43 protection suitable for incorporation fp mccb ( v tech ) n1 frame upto 125a, isolators and including give connection with wire and cable etc complete all as specified and directedby engineer in charge . 176 supply and fix pvc body tent / industrial type desert cooler ( 1135x600x1535mm ) alongiwth four wheels, electric driven ( single phase ) , 3 speed motor with 950 rpm, 30 inch axial type fan , noise level 68 db, having nominal air flow capacity of 18000cmh / 10500 cfm, large size, pad size ( 1100x100x1150mm ) , water tank 90l capacity, black color complete all as specified and directed by engineer in charge 177 hanging only ceiling fan ( m.d. supply ) and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed by engineer in charge 178 fixing only exhaust fan ( m.d. supply ) and connecting upincluding provision of cable from ceiling rose / connector to fan and clean the existing exhuast fan with chemical solution complete all as specified and directed by engineer in charge 179 s&f rj 45 data and tv socket eachfor connection of data network and tv cable ( dish ) complete all as specified and directed by engineer in charge 180 s&f rigid non metaliic pvc conduit 20mm dia inclusive of all tees, bends , elbows , reducers , bell mouth tube ends and complete with all fixing accessories such as couplers , lock nuts, saddles, pipehooks etc complete all as specified and directed by engineer in charge 181 s&fsteelbody exhaust fan of 300mm sweep , 240 volt , 900 rpm, 5 star rating complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core pvc insulated pvc sheathed copper conductor flexible cable 24 / 0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to disturbed wall in cm ( 1:4 ) white washing matching with existing color etc complete all as specified and directed by engineer in charge 182 supply and filling in sand for cable protection complete all as specified and directed by engineer in charge 183 supply and lay standard size bricks subclass b type complete all as specified and directed by engineer in charge 184 m&l for fixing gi tubing ( light grade ) 80mm bore for cable protection laid under path / trench / wall / on pole all as specified and directed by engr in charge. 185 supply and lay jointing and testing and commissioning in replacement of 35 sqmmx4 core xlpe insulated, screened , pvc bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & pvc sheathed lt cable 1100 v grade conforming to is 7098 laid in trenches / ducts / fixed on poles wall / laid under roads / paths / drain / culverts or passing through pipes complete all as specified and directed by engineer in charge. 186 m&l for galvanized steel water tubing medium grade of 25 mm bore with & including all fittings complete, laid in trenches / wall or floor , and connections of 25 mm bore, complete all as specified and directed by engineer in charge. 187 supply & fixing mild steel clamps made of flat iron 40x6mm in two halves for tapping through 40 to 100mm bore gi / di water pipe line including drilling and welding of 15 25mm gi socket and necessary rubber insertion, nut, bolts & washers complete all as specified and directed by engineer in charge. 188 s&f 20mm bore gun metal gate valve ( isi marked ) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 20mm bore, complete all as specified and directed by engineer in charge. 189 m&l for cutting existing steel tubing for alterations or additions for 40mm to 50 mm size screwing existing steel tubing for alterations or additions ( or lengthening screw on pipe to form connector ) complete all as specified and directed by engineer in charge. 190 s&f 25mm bore gun metal gate valve ( isi marked ) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 20mm bore, complete all as specified and directed by engineer in charge. 191 supply, fixing , testing & commisioning of electric chimney ( 90 cm ) with feature of baffle filter, inbuilit light, touch screen control panel, noise level, 58 db, stainless steel body, air suction capacity 1200 cmh, speed level 3 , motor power 180 watt, input vol 220 240 v / 50hz, remote controlled and fitting in wall as connecaled or duct all as specified and directed by eng in charge. 192 supply and fixing of ms powder coated fly catchers machine with dimensions ( l 24.5 x d 5.5 x h 17 ) , light source philips actinic uv tubes ( two tubes ) , capacity of 18 watt each of tube all as specified and directed by engr in charge. 193 note : ( i ) amount ofcredit for retrieved materials is mentionedin sch a section ii of tender documents in pdf form which will be deducted while acceptance of tender offline....
Due Date : December 07, 2023
Tender Value : ₹ Ref. Documents