Military Engineer Services - Rajasthan

40896071 tender for provision of certain sanctioned works in zone b under ge banar; 1 surface excavation not exc. 30 cm deep and averaging 15cm deep and getting out in soft / loose soil complete all as specified. 2 excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out any type of soil complete all as specified. 3 excavating in post holes ( or similar holes ) each n exc 0.5 cum, getting out, returing, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm watering and removing surplus soil to a distance n exc 50m and making and removing surplus soil to a distance n exc 50m and making good surface in hard / dense soil complete all as specified. 4 returning, filling in, including spreading, levelling, watering and wellramming in layers not exc 25cm in soft / loose soil complete all as specified. 5 removing excavated material n.exc. 50 m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified. 6 m&l cement concrete 1:4:8 type d2 ( 40mm graded stone aggregate ) in foundations, filling and mass concrete complete all as specified. 7 all as per ser item no 6.00 but pcc 1:3:6, type c2. 8 use & waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or to batter flat and rough finished surfaces of concrete complete all as specified. 9 use & waste formwork to edges of concrete flats, treads breaks in floors, window cills, concrete rallings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20 cm wide and rough finished surfaces of concrete complete all as specified. 10 use & waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) flat and rough finished surfaces of concrete complete all as specified. 11 m&l forrcc ( design mix ) m 25, using 20 mm graded stone aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified. 12 m&l forrcc ( design mix ) m 25, using 20 mm graded stone aggregate in beams, cantilevers, bressumers, lintels over 1.5m span complete all as specified. 13 m&l forprecast 1:2:4 rcc, using 20 mm graded stone aggregate in cover slab complete all as specified. 14 m&l forrcc ( design mix ) m 25, using 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified. 15 m&l mild steel tmtbarsin reinforcement 10mm dia and overcut to length bent to shape required including crankingbindingspirally, hooping for columns hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia complete all as specified. 16 m&l mild steel tmt barsin reinforcement5mm dia and over up to 10mm dia in stirups andcut to length bent to shape required including crankingbindingspirally, hooping for columns hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia complete all as specified. 17 m&l for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, modular bricks in cement mortar built in cm 1:6 complete all as specified. 18 m&l for 15mm thick rendering in cm 1:4 mixed with wpc on fair faces of brick work or concrete surfaces of wall complete all as specified.note: wpc shall be measured and paid separately. 19 material and labour for preparation of newly plastered surface of walls and applying two coats of cement base paint over one coat of alkali resistance primer complete all as specified. 20 m&l for integral water proofing compound in external plastering complete all as specified. 21 m&l for preparation of newly plastered or unplastered surfaces of and applying three coats of white wash complete all as specified. 22 all as per ser item no 21.00 but on wall ceiling. 23 m&l for 100 mm thick cement concrete for sub base type d2, 1:4;8 ( using 40 mm graded aggregate ) complete all as specified. 24 m&l 25 mm thick cement concrete for sub base b 1, 1:2:4 ( 20mm graded aggregate ) complete all as specified. 25 m&l for non skid ceramic colour tiles ( 300 x 300 mm ) x 7 mm thick in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick bedding of cm 1:4 layer in floor finishes complete all as specified. 26 m&l for coloured glazed ceramic tiles in vertical surface 350x250x7mm / 450x350x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles in vertical surface including 10mm thick renderingin cm 1:4 complete all as specified. 27 m&l for hardcore of gauge n exc. 63mm ( broken stone or boulders ) , deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified. 28 m&l 75 mm thick pcc ( 1:3:6 ) type c1 ( by using 20mm aggregate ) in plinth protection and similar work complete all as specified. 29 s&f 125 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified. 30 s&f 100 mm long extruded aluminium alloy handles, fabricated type., anodised complete all as specified. 31 m&l solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s square tube, supplying & fixing in opening as per specification complete all as specified. 32 m&l factory made solid panel of pvc door shutter 30mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails, m.s. frame shall be covered with heat moulded plain colour pvc `c channel heaving a pvc sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s frame wedded / sealed to the stiles, & rails with suitable pvc sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified. 33 s&f 100 mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type b 21 complete all as specified. 34 s&f steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified. 35 s&f sheet glass 4 mm thick, figured glass, pin headed type and glazing with oil putty or wooden beads supplied with shutters in square n.exc 0.5 sqm in each pane complete all as specified. 36 m&l two coats of synthetic enamel paint over a red oxide primer including prepration of newly treated steel surfaces of girth exc 10cm complete all as specified. 37 all as per ser item no 36.00 but n.exc 10 cm width or girth. 38 s&f 15mm dia galvanized steel tubing, medium grade, with all fitting and fixed complete to walls celling or laid in floors complete all as specified. 39 s&f 20mm dia galvanized steel tubing, medium grade, with all fitting and fixed complete to walls celling or laid in floors complete all as specified. 40 all as per ser item no 39.00 but 25 mm bore. 41 m&l for vitreous china wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified. 42 m&l for vitreous china squatting pan, `orissa pattern, size 580 x440 mm white, with integral foot rests ( excluding flushing cistern and flush pipe ) complete all as specified. 43 m&l for pvc valveless, syphonic action type, flushing cistern, 10 ltr capacity, low level, white, with inlet, ball valve, float and handle including brackets and including flushing pipe 32 mm dia of bore, high density polyethylene pipes of pressure rating 6 kg / sqcm complete all as specified. 44 s&f pvc connections 15mm size with ptmt nuts of length 450mm complete all as specified. 45 m&l for 15mm dia of bore cast copper alloy stop valves, fancy type, chromium plated, screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified. 46 s&f 15mm pillar taps, cast copper alloy, with capstand heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed to 15 mm size pipe complete all as specified. 47 s&f pvc waste pipe 32mm dia for whb complete all as specified. 48 s&f 15mm dia bib tap cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified. 49 m&l for 110mm pvc ( swr ) pipes, single socketed, in any length, with rubber rings joints, laid in trenches or in floors complete all as specified. 50 m&l for 75mm pvc ( swr ) pipes, single socketed, in any length, with rubber rings joints, fixed to walls complete all as specified. 51 m&l for 75mm dia of bore pvc ( swr ) floor trap plain with grating including jointing with solvent cement complete all as specified. 52 m&l for 110mm pvc ( swr ) bends any radius complete all as specified. 53 all as per ser item no 52.00 but 75 mm. 54 m&l for 75mm dia pvc ( swr ) vent cowl complete all as specified. 55 s&f 110mm pvc ( swr ) p trap complete all as specified. 56 m&l 110 mm pvc ( swr ) branch piece, single ( y ) equal or unequal complete all as specified. 57 cutting of bituminous / pcc / pqc road for laying of pipe line not exceeding 1.5 m depth / width inculding making good to distributed portion to match with existing road / path with pcc complete all as specified. 58 m&l 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick ac building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified. 59 s&f 500 litre capacity rotational moulded polyethylene water storage tanks ( cylinderical vertical with closed top ) hoisted and fixed in position all as specified in ssr part i including 20mm brass ball valve high pressure complete all as specified. 60 material and labour for square rubble walling jodhpur type regular course well bonded bedded and solidly hearted built in cement mortar ( 1:6 ) complete all as specified. 61 extra over on stone walling for hammer dressing to face stone with maximum depression on face from straight edge n.exc 20mm and dressing faces beds and joints as specified to square rubble walling regular course jodhpur type complete all as specified. 62 m&l for structural steel in roof trusses ( framed ) trussed, purlins, crane gantries, rails and fastening and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, columns, cleats etc ) 63 s&f rolled sections as in fencing post or similar work fe 410w ( gde e 250 ) quality a complete all as specified. 64 s&f pre painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50mm of an colour having tensile strenght of 550 mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified. 65 s&f pre painted galvalume aluminium zinc coating gi based plain steel sheet 0.50mm of an colour having tensile strenght of 550 mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified. 66 mild steel screw bolts ( machine made ) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut n exc 15 cm long dia of shank 11 to 15 mm complete all as specified. 67 m&l for sand filling under floor including watering and consolidation 25 mm thick complete all as specified. 68 m&l for glossy finished machine pressed precast concrete interlocking paver block any shape and size conforming to is 15658 2006 of 60 mm thickness m 35 grade with white cement glossiness in pigments and laid in position / patterncomplete all as specified. 69 m&l for pre cast concrete block as in kerb stone ( machine made ) with solid blocks type b1, 1:2:4 ( 20mm graded stone aggregate ) exc 10 cm in width and setting in cement mortar 1:4 complete all as specified. 70 pcc ( 1:4:8 ) type d2 using40mm graded crushed stone aggregatein concretebedding to drain pipes, including packing under and haunching against the sidesof pipes after they are laid and tested complete for 150mm bore pipe complete all as specified. 71 m&l reinforced concrete pipes 150mm bore, class np 2, laid and jointed complete all as specified. 72 m&l precast cement concrete block masonary with solid block of ( 1:4:8 ) type d2 exc 10 cmin width & setting in cm ( 1:6 ) complete all as specified. 73 m&l cement concrete ( 1:2:4 ) type b1 using 20 mm graded crushed stone aggregate in surface channels or drains and benching including finishing the top of benchingeven and smooth using extra cement complete all as specified. 74 extrafor formingfairfinisheddrain orchannel 30cminner girth in cementconcreteusing extracementincluding forms, moulds, mitred / stoppedends etc complete all as specified. 75 add to srl item no. 74.00 above for each 25mm girth or part thereofover 30cm. 76 m&l rendering 5 mm thick in cement mortar 1:3 on caling / roof projection / chajja complete all as specified. 77 m&l for pcc 1:2:4 type b 1 as in coping incl necessary form work complete all as specified. 78 m&l for keyed pointing in cm 1:3 to squared rubble, coursed or uncoursed stone masonary complete all as specified. 79 m&l for rendering screed bed or bedding layer of mortar 10 mm thick in cm 1:3 as in floor / roof to be finished smooth without using extra cement mixed with water proofing compound as per manufacturer instruction complete all as specified. 80 m&l for moorum / red bajri filling in floors or pavings, spreading and levelling in layers and well ramming including watering as required complete all as specified. 81 s&f viterous china bowl urinal flat back, size 465x355x265 mm white ( minimum ) , with grating and union for discharge pipe ( excluding flushing cistern, flush pipe and waste pipe ) complete all as specified. 82 s&f viterous china urinal partition white of size 310x700 mm complete all as specified. 83 m&l for urinal spreader of ptmt any colour for fixing with 15 mm dia pipe ( minimum weight 60 gms ) complete all as specified. 84 s&f for 32 mm bore waste coupling of ptmt ( half full threaded ) ( minimum weight 32 45 gms / 40 60 gms ) complete all as specified. 85 cutting into existing manholes for connecting new drains ( internal dia of pipe 150 mm ) making good to pipe and rendering, cutting out existing benching for and forming branch channel ( 1 / 2 round or 3 / 4 section ) in cement concrete 1:2:4 type b 1 smooth finished and reforming benching complete all as specified. 86 m&l for providing polythene film, black, 200 micron laid in floors complete all as specified. 87 m&l for cement concrete work in pavement / hardstanding of flexural strength, 40 kg / per square centimeter in field using 400 kg of cement per cubic meter thickness of concrete upto 20 cm complete all as specified. 88 m&l for finishing surfaces with brooming complete all as specified. 89 m&l for forming contraction ( dummy ) joints 65mm deep x 10mm wide and filled with sealing compound grade a complete all as specified. 90 m&l plain cement concrete 1:2:4 type b 1 using 20 mm graded stone aggregate asin cast in situ in lintels up to 1.5 m span, cills and other similar bands, plinth courses, parapets, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work complete all as specified. 91 supply only ms galvanized chain link fencing of size 100mmx100mm square mesh of 10 gauge type complete all as specified. 92 fixing only chain link fencingincluding line wires, any mesh, size andy type of standards, rails, straining bolts etc. complete including provision of binding wire complete all as specified. 93 m&l galvanized, 2 strand, steel barbed wire, 2.24 mm dia barbed with 2 mm dia barbs at 75 mmspacing and straining and fixing to any type of standard rails, straining boltsincluding securing or tying atcrossing with and provision of galvanized ms wire staples or steel pins etc ( each line wire to be measured ) complete all as specified. 94 m&l for point wiring of one light point controlled by one, one way switch complete with any length using approved colour coding as per is, with stranded copper conductor 1.5 sq.mm ( nominal area ) , single core, pvc insulated and unsheathed stranded frlscable 1100 volts grade, isi 694 marked, in pvc rigid conduits heavy duty isi marked totally concealed in wall / floor / roof including all accessories etc. with sunken boxes suitable for mounting switches / sockets etc. and pvc insulated stranded copper conductor 1.5 sq.mm single core cable as earth and connecting to common earth dolly complete all as specified for the following: note ( i ) cutting in chases and pointing in will be done by contractor without any cost. ( ii ) making good of distrubed surfaces matching with existing finishes will be done by contractor without any extra cost. 95 one 5 pin 5 amp socket outlet point on same board with other switches including earth wire. 96 s & f piano flush type switch 5 amps single pole all as specified. 97 s & f multipurpose socket outlet with piano flush type 3 pin 5 amps all as specified. 98 s&f ceiling rose surface type three terminalscomplete all as specified. 99 s & f led lights fitting 1x 20w, 220v, ac decorative box type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified. 100 supply and fixing earthing complete with gi earth plate eletrode 60 cm x 60 cm x 6.0 mm thick barried directly in ground vertically to a depth note less than 2.25 metres below ground level with top edge of earth plae at a depth note less than 1.5 metres below level ground, connected to gi iron or steel earth wire 4 mm dia ( 8 swg ) by means of nuts , bolts checks nuts, washers andearth wire protected by gi iron pipe 15 mm bore, medium grade and connected to main switch board or main control board as directed and including concrete pit in pcc ( 1:3:6 ) type c1, pre cast rcc coverslab 30cmx30cmx10cm with one lifting handle made of 8mm dia ms bar funnel wire mesh, 20mm bore gi or steel pipe medium grade for watering, charcoal or coke and salt in alternate larges, necessary excavatin and earth work in any type of soil complete all as shown electrical plate no 3 of mes schedule part i and testing after completion. 101 s&f mcb spn db 4 way, double door, with 200 amp rated busbar 240 v, complete all as specified. 102 supply and fixing mcb sp 6 32 amp 240 volts. 10 k complete all as specified. 103 mcb spn32 amp 240volt c series 10ka complete all as specified. 104 s & f led lights fitting 1x 10w, 220v, ac decorative / mirror type type with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 105 drilling ofwater pipe line of any type and size upto 50 mm size for connection of 25 / 20 mm gi pipe with clamp and other assesries complete all as specified. 106 supply and fixing 20 mm bore gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe, non rising forged brass spindle class i and fixed with required necessary gi fittings complete all as specified. 107 all as per ser item no 105.00 but 15 mm. 108 all as per ser item no 105.00 but 25 mm. 109 m&l for clean, dry sand in trenches / ducts for cushioning to cable complete all as specified. 110 supplying and laying pcc cable cover, flat, class lv, type 2 of size 300mm x 180mm x 40mm complete all as specified. 111 supply laying and testing cable xlpe insulated, screened, pvc bedded galvanised steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with standed allumiuium conductor of size 10 sqmm 2 core complete all as specified. 112 supply and lay galvanised medium grade including fitting 40 mm dia with all fittings laid in trenches / floor complete all as specified. 113 supply and fix heavy duty metal bodyexhaust fan 300 mm sweep, including louvers, grounting with nut bolts complete all as specified. 114 s & f led security lightluminaries 35 watt complete with all accessories andwall mounting bracket of suitable size including clamps, nut bolts etc. prewired complete all as specified....

Military Engineer Services - Rajasthan

40876954 tender for repair to certain black top road, culverts, retaining wall etc at rms dholpur; 1 m & l preparing existing black top surface by brushing with wire brushers for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and directed. 2 m&l for applying evenly a priming / tack coat with bituminous primer using paving bitumen vg 10 grade @ 05 kg per 10 sqm complete all as specified and directed. 3 m&l bituminous premix semi dense asphaltic concrete 30mm thick ( consolidated thickness ) using paving bitumen vg 30 with 5.5% binder content by weight of total mix laid with mechanical power and rolled with 8 to 10 tonne power roller and compacted to required camber and gradient complete all as specified and directed.note : ( i ) in case the binder contents by weight of total mix is less than 5.5% as per actual design mix , the price adjustment shall be made as per average rates of all paid voucher for bitumen pertaining to this work. if total binder contents as per actual design mix is more than 5.5%, no price adjustment shall be made for the same. ( ii ) job mix formula for bitumenous macadam shall be obtained from the institutions specified in ca prior to commencement of work and shall be got approved from the ge. 4 m&l for premix bituminous macadam with 4% bitumen binder of total mix laid / rolled and compacted to required gradient and camber ( consolidated thickness 75mm or less ) ( using paving bitumen vg 30 ) by weight of total mix spread, rolled and consolidated with 8 to 12 tonne power roller to required gradient and camber complete all as specified and directed.note: ( i ) in case the binder contents by weight of total mix is less than 4% as per actual design mix , the price adjustment shall be made as per average rates of all paid voucher for bitumen pertaining to this work. if total binder contents as per actual design mix is more than 4%, no price adjustment shall be made for the same. ( ii ) job mix formula for bitumenous macadam shall be obtained from the institutions specified in ca prior to commencement of work and shall be got approved from the ge. 5 supply and fixing cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with pama striplens reflector of model no. da 972.0 fixed with and incl ms stud of suitable size as per manufactures instructions complete all as specified and directed. 6 supply and fix solar cat eye aluminum alloy shall ( 100% water proofing design according to 65 ) of size 125mm x 125mm x 25mm ( shank 65mm ) of high efficiency mono rystafie solar panel 2.4v / 0.3 watt one ni ed rechargeable battery ( 1.2v / 1600ma ) consisting of super bright led with 10, 000 to 18, 000 mcd completed as per manufactures instructions etc. complete all as specified and directed. 7 m & l for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to bs 3262 1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed. 8 demolition of brick work or stone / bolder masonary, built in cement mortar including all quions, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed. 9 m&l for walling of random rubble, uncoursed well bonded bedded, and solidily hearted, built in cement mortar 1:6 complete all as specified and directed. 10 m&l for stone walling of random rubble, uncoursed well bonded bedded, and solidily hearted, built in cement mortar 1:6 but exceptstone complete all as specified and directed. 11 extra over stone walling for hammer dressing to face stones and dressing, of face beds and joints, as specified, of random rubble walling uncoursed or brought up to courses with maximum depression on face from straight edge held against the dressed surface n. exc. 40 mm, on lime or sand stones complete all as specified and directed. 12 m&l for plain cement concrete type b1 1:2:4 ( 20 mm graded aggregate ) as in lintels upto 1.5 m clear sp and other similar bands, plinth courses, string courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones bed plates, water troughs and the like including weathering, slightly rounded or chamfered anglesand throating, complete all as specified and directed. 13 m&l forflush pointing to random rubble masonry, uncoursed or brought up to courses in cement mortar 1:4 complete all as specified and directed. 14 demolition of cement concrete ( unreinforced ) in ground floors and pavings n exc 15 cm thickness ( below or above ground level ) and removing unserviceable material exc 100 mtr complete all as specified and directed. 15 m&l for pcc 1:3:6 type c2 using 40mm graded aggregate 75mm thick in floors / pvaings ( for both sides of road ) complete all as specified and directed....

Military Engineer Services - Rajasthan

40874623 tender for special repair of qtr 57 and 60 ( offers md accommodation ) of certain unit at mil station kota. ; 1 demolition / dismantling of existing roof treatment, any type from rcc roof slab including lime concrete / pcc padding over roof, removing layer of bitumen under lime concrete / pcc padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside md land, complete all as specified and directed. 2 demolition / dismantling of existing roof treatment, any type from rcc sunken slab including lime concrete / pcc filling materials around wc upto top of existing sunken slab, removing layer of bitumen under lime concrete / pcc sunken, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside md land, complete all as specified and directed. 3 taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. 4 taking down chowkhat or frames not exc 1.50 sqm each with shutters ( with out taking off shutters from the frame ) , complete all as specified and directed. 5 taking down chowkhat or frames exc 1.50 sqm and not exc 4.00 sqm each with shutters ( with out taking off shutters from the frame ) , complete all as specified and directed. 6 takingdown shutters of any description exc 1 sqm and not exc 2 sqm each and removing from site complete all as specified and directed. 7 takingdown shutters of any description exc 2 sqm each and removing from site complete all as specified and directed. 8 takingdown and re fixing after rescuring or easing and adjusting of any description exc 1 sqm & n. exc 2 sqm each in the same opening complete all as specified and directed. 9 takingdown and re fixing after rescuring or easing and adjusting of any description exc 2 sqm each in the same opening complete all as specified and directed. 10 demolition of cement concrete ( un reinforced ) of any description and in any position not otherwise specifically provided for and removing rubbish from premises ( distance exc 1.5 km but not exc 5 km ) , complete all as specified and directed. 11 demolition of cement concrete ( un reinforced ) in ground floor and pavings n.exc 15 cm thickness ( below or above gl ) and removing rubbish from premises ( distance exc 1.5 km but not exc 5 km ) , complete all as specified and directed. 12 demolition of cement concrete ( reinforced ) as in roofs, floors ( other than ground floors ) , beams, staircases, landing, chajjas and similar suspended work for and removing rubbish from premises ( distance exc 1.5 km but not exc 5 km ) , complete all as specified and directed. 13 dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. 14 demolition of stone slabs and tiles of any description or thickness in floors etc, laid, bedded and pointed in any mortar, complete all as specified and directed. 15 dismantling floor, hearth or wall tiling / terrazzo including cement mortar bedding ( but not backing ) , removing tiles and rubbish off the premises, complete all as specified and directed. 16 demolition of brick work or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles, complete all as specified and directed. 17 providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sqm of the vertical surface of the sub structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed. 18 treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 ( 1 cement: 2 coarse sand ) to match the existing floors complete all as specified and directed. 19 m&l brick work with old size pulverized fuel ash lime bricks ( fly ash bricks non modular size ) , straight or curved on plan exc 6 m mean radius, built in cm 1:6, complete all as specified and directed. 20 m&l for brick work with pulverised fuel ash lime bricks ( fly ash bricks non modular size ) , straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed. 21 m&l for pcc 1:3:6 type c 2 ( using 40mm graded stone aggreate ) , 75 mm thick as in plinth protection / path / pcc paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where dirtected and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling ( one part of hot bitumen 85 / 25 and three parts of fine sand by weight ) , complete all as specified & directed. 22 m&l for 100mm thick plain cement concrete 1:3:6 type c 2 ( using 40 mm graded crushed stone aggregate ) as in flooring / sub base finished surface even & fair to receive floor finishes / screed complete all as specified and directed. 23 m&l for 50mm thick plain cement concrete 1:2:4 type b 2 ( using 40 mm graded crushed stone aggregate ) as in flooring finished surface even & smooth without using extra cement complete all as specified and directed. 24 m&l providing cement concrete 1:2:4 type b 1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating & formwork, complete all as specified and directed. 25 m&l providing cement concrete 1:2:4 type b 1 using 20 mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed. 26 s & f 40mm gi pipe, medium grade, 60cm long out of which 20cm projected outside for spout pipe, placed in slope to drain water accumulated in sunken portion including making good in cm 1:3 for the damaged portion complete all as specified and directed. 27 m&l for pcc 1:2:4 mix type b 0 ( using 12.5 mm graded crushed stone agg ) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed. 28 m&l brushing neat cement slurry with 3.00 kg cement per sqm, complete all as specified and directed. 29 m&l for applying 15 mm thick screed in cm 1:4 on roof slabs with using liquid water proofing compound as per manufacturers instructions, complete all as specified and directed. ( liquid wpc shall be measured and paid separately ) . 30 m&l for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and supply and fix app polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 kg / sqm, black finish reinforced with non woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to is 3384 @ of 0.40 kg / sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. note: ( i ) coved fillets in pcc ( 1:2:4 ) type b 0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall / mumty / chimney / other vertical surfaces and thereafter surface painted with hot paving bitumen of grade 30 / 40 confirming to is 73, applied@1.20 kg / sqm over a coat of cold applied bituminous primer conforming to is:3384 @ 0.40 kg / sqm. 31 item 30.00 contd........ ( ii ) polymeric membrane shall be taken to a height of 45cm ( minimum ) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. ( iii ) the waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. ( iv ) in case of stone masonry parapet wall etc a groove of size 25mmx25mm ( minimum ) shall be made in coved fillet at the junction of roof and parapet wall / mumty chimney / other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. ( v ) cost of above aspects is deemed to be included in quoted rates. 32 m&l for cleaning of walls and floor of sunken portions including picking, sweeping clean and washing down with water to remove dust, dirt etc and supply and fix app polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 kg / sqm, black finish reinforced with non woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to is: 3384 @ 0.40 kg / sqm, torching overlaps with a propane or a butane gas torch with an overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold applied bituminous primer all as per manufacturer’s instructions, complete all as directed.note: ( i ) the waterproofing treatment shall be got carried out through the manufacturer or their authorized applicators only. 33 supply only approved liquid water proofing compound, complete all as specified and directed. 34 s&f 35mm thick factory made iind class hard wood ( hollock ) paneled door shutters two panel with lock rail and panel of 9mm b.w.p. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to is 710 or 12mm thick particle board veneered with commercial veneering on both faces. the size of rails & style as specified in ssr part i ( 2009 ) section 8 and as per is 1003 ( part i ) kiln seasoned as per is 1141 and chemically pressure treated as per is 401 complete all as specified and directed. 35 s&f 35mm thick factory made iind class hard wood ( hollock ) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass / gauge etc. the size of rails & style as specified in ssr part i ( 2009 ) section 8 and as per is 1003 ( part i ) kiln seasoned as per is 1141 and chemically pressure treated as per is 401 complete all as specified and directed.note : s & f glass / gauge shall be measured and paid for separately. 36 m&l in renewal of 18 / 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. 37 s&f in renewal of factory made pressed steel cupboard shutters alongwith frame, frame made of 1.25 mm thick pbi sheet and shutter made of 1.00 mm thick pbi sheet with 6 nos 3.15 mm thick and 100 mm long steel hinges per shutter, godrej pattern locking arrangement with 12 mm dia vertical rod and lock with duplicate key & chrome finish handle, duly spray painted in factory with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete with fastener, hold fast etc as required at site, complete all as specified and directed. ( total width including frame shall be measured for payment purpose ) . 38 s&f in renewal of 18 mm thick hdwpc ( high density wooden plastic composite ) kitchen cupboard / door shutter board, one side colour / white laminate and other side decorative as in modular kitchen / cabinet door shutters fixed with minifix hardware where ever required & including edge band 22 mm wide 0.80m thick of matching colour on exposed surfaces of board fixed with polymaster adhesive including trimming edges of edge band to true line of thickness of board by manual trimmer, fixed to wall etc, complete all as specified and directed. 39 s&f in renewal of 18 mm thick hdwpc ( high density wooden plastic composite ) board of both side white laminate as in back kitchen and other side un decorative as in back of kitchen cabinet / partition of cupboard etc, complete all as specified and directed. 40 s & f in renewal continuous ( piano ) hinges, stainless steel, matt or brush finish, width of flaps ( when open ) in 40mm complete all as specified and directed. 41 s&fof ball catches with 8 mm dia steel ball and brass body and striking plate including letting in and fixed, complete all as specified and dirceted. 42 s&f ss handles, fancy type, 100 mm size, complete all as specified and directed. 43 s & f auto closing hinges, three dimentional adjustment with suitable mounting plate made of stainless steel with nickel plated for corrosion resistance for cupboard and cabinet shutters of kitchen, complete all as specified and directed. 44 s & f in renewal of kitchen basket cutlery stainless steel of size 435mmx510mm & including ss guide channel etc, complete all as specified and directed. 45 s & f in renewal of kitchen basket plate rack stainless steel of size 435mmx510mm & including ss guide channel etc, complete all as specified and directed. 46 s & f in renewal of kitchen basket utensils stainless steel of size 435mmx510mm & including ss guide channel etc, complete all as specified and directed. 47 s&f of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140 mm, complete all as specified and directed. 48 s&f aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed, complete all as specified and directed. 49 s&f aluminium handles, cast type, anodised 100 mm size, complete all as specified and directed. 50 s&f aluminium handles, cast type, anodised 150 mm size, complete all as specified and directed. 51 s&f 100 mm sizemild steel butt hinges, isi marked, medium weight, cold rolled and fixed with screws, complete all as specified and directed. 52 s & f 250 mm long aluminium alloy, anodised sliding door bolts ( isi marked ) with bolt not less than 16mm dia with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy and fixed complete all as specified and directed. 53 s&f 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, welded to mild steel frame complete all as specified and directed. 54 s&f snake guard ( door seal aluminium plate with rubber beading ) for door etccomplete all as specified and directed. 55 supply only stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, fixed to door, window, ventilator etc complete all as specified and directed. ( note: cost of fixing of wire cloth shall be deemed included in the unit rates under respective items. ) 56 s & f for solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s. square tube, suppling & fixing in opening as per specification & drawing as applicable to item 08095 given in ssr part – ii ( 2020 ) . 57 s & f for factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in ssr part–ii. 58 providing and fixing factory made upvc white colour sliding window ( area not exceeding 2.00 sqm each ) , three track made of extruded profiles with wall thickness of 2.3mm ( + 0.2mm ) . window profile with hollow section with multi chamber. frame ( 88mm x 52mm ) , sliding sash ( 42mm x 67mm ) . sliding mesh sash ( 42mm x 57mm ) sliding interlock ( one vertical length in each shutters ) ( 45.5mm x 28mm ) , glazing bead ( 24.5mm x 16mm ) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. epdm gasket, 1.2+ 0.2mm thick galvanised steel frame ( 30mm x 18mm ) 2 nos, sliding sash ( 30mm x18mm ) , sliding mesh sash ( 26mm x 10mm ) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, hardware.touch lock of zinc alloyed ( white powder coated ) , steel roller system. stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories etc., complete all as specified and directed.note : ( i ) the unit rate quoted by contractor includes cost of glass and ss steel wire cloth and includes all other connected accessories. net opening will be measured for payment purpose. ( ii ) provision for fixing the ac and cooler shall be included in rate quoated by the bidder, no payment shall be made on this account and no misunderstanding entertained in later stage. ( iii ) bidder shall note that all the accessories ( packing, hinges, handles etc ) of upvc window shall be maintained by manufactureres till defect libility period and quoated rate shall be included this provision. 59 supply and fixing factory made upvc white colour fixed glazed window / ventilator made of ( small series ) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension ( area upto 0.75 sqm. ) comprising of upvc multi chambered frame and mullion ( where ever required ) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length ( shape & size according to upvc profile ) , upvc extruded glazing beads of appropriate dimension, epdm gasket, g.i. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. profile of frame shall be mitred cut and fusion welded at all corners, mullion ( if required ) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality including provision of exhaust fan etc., complete all specified and directed. note : ( i ) for upvc frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. ( ii ) the unit rate quoted by contractor includes cost of glass and ss steel wire cloth and includes all other connected accessories. net opening will be measured for payment purpose. ( iii ) provision for fixing the exhaust fan shall be included in rate quoated by the bidder, no payment shall be made on this account and no misunderstanding entertained in later stage. ( iv ) bidder shall note that all the accessories ( packing, hinges, handles etc ) of upvc window / ventilator shall be maintained by manufactureres till defect libility period and quoated rate shall be included this provision. 60 s&f factory made steel windows conforming to is 1038 with side hung shutters & including box type hinges, with 2 nos steel handles, 2 nos tower bolts & steel pag stay complete ( without glazing bars ) , dovetailed or welded including fixing of lugs in pcc 1:2:4, type b 1, using 20mm graded stone aggregate & making good walls & cills to match the existing and including one coat of red oxide / zinc chrome primer complete all as specified and directed.note : ( i ) ss or ms cloth wire shall be measured and paid for sepparately under respective items. ( ii ) window size and pattern wherever required and directed shall be suitable for installing desert cooler. 61 s&f factory made steel ventilator with top hung shutter including hinges, steel peg stay and including one coat of red oxide / zinc chrome primer complete all as specified and directed. 62 s&f factory made steel ventilator with fixed type shutter without glazing bars including hinges, steel peg stay and including one coat of red oxide / zinc chrome primer complete all as specified and directed. 63 welding in repairs thickness of metal to be welded not exc 6mm and length of welding exc 2.5 cm but not exc 5cm complete all as specified and directed. 64 s&f sheet glass 3 mm thick ordinary quality and glazing with oil putty etc in squares n.exe 0.50 sqm in each pane, complete all as specified and directed. 65 s & f of framed work as in doors or gates of angles or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with including either hooks and hinges or steel hanging door fittings ( excluding of steel sheeting or other covering running rails and guides ) and hanging also fastening and fixing, conforming to fe 290 grade e 165, complete all as specified and directed. 66 s&f mild steel framed work as in grills, grating etc. with end of bars shouldered and / or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: cages, frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to fe 290 grade e 165, complete all as specified and directed. 67 m & l for cutting holes in brick / stone masonary walls in cement mortar exc. half brick but not exc. one brick for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type b 1 as required, complete all as specified and directed. 68 dismantling plain or corrugated steel sheeting, any gauge, any thickness incl hooks and ridge as retrieved from site complete all as specified and directed. 69 s&f pre painted galvalume aluminium zinc coating gi based corrugated steel sheet, 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering, wall cladding etc, fixed to iron / wooden members with self drilling zincoulium coated metal screws having cap with rubber and metal washers, complete all as specified and directed. 70 re fixing only pre painted galvalume aluminium zinc coating ( gi based corrugated steel sheet, 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering, wall cladding etc, fixed to iron / wooden members with self drilling zincoulium coated metal screws having cap with rubber and metal washers, complete all as specified and directed.note : pre painted galvalume aluminium zinc coating sheets obtained from dismantling shall be reused under this item. 71 s&f in renewal of stainless steel tubular curtain rods, 25 mm dia, with fixing brackets and one pair of decorative end caps etc, complete all as specified and directed. 72 m&l 100 mm thick pcc 1:4:8 type d 2, using 40 mm graded crushed stone aggregate, as in sub base of floors, etc., finished surface even & fair to receive floor finishes / screed complete all as specified and directed. 73 m&l machine pressed precast concrete interlocking paver block any shape and size made with grey cement and pigment, confirming to is 15658 2006 of 60 mm thickness, m 35 grade, laid over and including 25 mm thick sand cushioning, complete all as specified and directed. 74 m&l for 25mm thick plain cement concrete 1:2:4 type b 1 ( using 20 mm graded crushed stone aggregate ) as in flooring / sub base finished surface even & fair to receive floor finishes / screed complete all as specified and directed. 75 m&l for joint free non skid ceramic coloured tiles, 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in cm 1:6, complete all as specified and directed. 76 m&l for light coloured vitrified tiles, 10mm thick ( square / rectangular ) area of each tile not exceeding 0.36 sqm ( 600x600mm ) , in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in cm 1:6, complete all as specified and directed. 77 m&l for light coloured vitrified tiles, 10mm thick ( square / rectangular ) area of each tile not exceeding 0.36 sqm ( 600x600mm ) , fixed on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 10 mm thick rendering in cm 1:4 backing, complete all as specified and directed. 78 m&l glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in cm 1:4 backing, complete all as specified and directed. 79 m&l for machine cut kota stone slab as in flooring 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing andmirror polishing by applying wax polish, laid over and including 15 mm thick screed bed in cm 1:4, complete all as specifiedand directed. 80 m&l for machine cut kota stone slab as in skirting, dado, risers etc, 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and mirror polishing by applying wax polish, laid over and including 15 mm thick rendering in cm 1:4, complete all as specifiedand directed. 81 m&l for grinding of the existing marble / kota stone flooring by mechanical process using corborundum stone of appropriate grit, cleaning & finally mirror polishing by applying wax polish complete all as specified and directed. 82 m&l black granite ( of any type ) slab 18 20 mm thick, table rubbed and mirror polished by applying wax polish as in cooking platform, jambs, cills, pillars, tread, risers, platform for whb etc including bull nosing to exposed outer edges, set in cm 1:4 bedding and pointing with white cement mixed with pigment and provn of hole for gas pipe, laid over and including 20 mm thick screed bed in cm 1:6, complete all as specified and directed.note : granite stone slab shall be laid in single piece with rounding of edges and a grove shall be provided beneath the projection portions of slab. 83 m&l for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed. 84 m&l for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed. 85 m&l for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4 ( using water proofing compound as per manufacturers instructions ) , surface finished even and smooth without using extra cement, complete all as specified and directed. ( liquid wpc shall be measured and paid separately ) . 86 m&l for rendering 5 mm thick on fair faces of ceiling in cement mortar 1:3 including finishing the surface even and smooth, complete all as specified and directed. 87 m&l for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over & including one coat of red oxide zinc chrome primer, complete all as specified and directed. 88 m&l for preparing old steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed. 89 m&l applying 2 coats of synthetic enamel paint over and including a coat of pink primer on wooden surfaces, exceeding 10 cm in width or girth, incl preparation of the new surfaces complete all as specified and directed. 90 m&l applying two coats of synthetic enamel paint on wooden surfaces, exceeding 10 cm in width or girth, incl preparation of the old surfaces complete all as specified and directed. 91 m&l preparation of newly plastered surfaces of walls and applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying two coats distempering with 1st quality acrylic distemper ( ready mixed ) having voc content less than 50 gms / litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification over new surfaces on walls complete all as specified and directed. 92 m&l for complete removal of existing treatment from previously treated plastered / unplastered surfaces of walls and applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying two coats distempering with 1st quality acrylic distemper ( ready mixed ) having voc content less than 50 gms / litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification over new surfaces on walls complete all as specified and directed. 93 m&l preparation of newly plastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10sqm over new surfaces over new surfaces on walls complete all as specified and directed. 94 m&l for complete removal of existing treatment from previously treated plastered / unplastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10sqm over new surfaces over new surfaces on walls complete all as specified and directed. 95 m&l for applying three coats of white wash on ceiling including preparation of new or previously untreated surfaces, complete all as specified and directed. 96 m&l for applying two coats of white wash after preparation of old previously treated plastered surfaces of walls, complete all as specified and directed. 97 m&l for applying one coat of white wash after preparation of old previously treated plastered surfaces of ceiling, complete all as specified and directed. 98 s&f in renewal of hdpe pvc connection 450 mm long suitable for 15 mm gi pipe with two ptmt nuts and rubber washers complete all as specified and directed. 99 s&f in renewal of vitreous china wash hand basin white with flat back of size 550x400 mm, excluding chain and plug, taps and porcelain stopper but incl pvc waste pipe of 32 mm bore, suitable size of waste fittings, one pair of 600 mm long cast iron brackets, complete all as specified and directed. 100 s&f in renewal of shower rose, chromium plated brass, 100 mm size with swivel joint, screwed to iron pipe or for union of 15 mm dia, complete all as specified and directed. 101 cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed. 102 taking up or down existing gi tubing and connections, including making good the disturbed surface for 15 mm bore pipes complete all as specified and directed. 103 taking up or down existing gi tubing and connections, including making good the disturbed surface for 20 mm bore pipes complete all as specified and directed. 104 supply, fixing, laying & testing 15 mm bore galvanised iron water tubing medium grade with and including all gi fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed. 105 supply, fixing, laying & testing 20 mm bore galvanised iron water tubing medium grade with and including all gi fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed. 106 dismantling existing water storage tank of any description of capacity exc. 250 ltr but n.exc. 500 ltr, complete all as specified and directed. 107 dismantling existing water storage tank of any description of capacity exc. 500 ltr but n.exc. 1000 ltr, complete all as specified and directed. 108 s&f in position rotational moulded polyethylene water storage tanks 500 lts capacity, white colour ( cylinderical verticalwith closed top ) hoisted and fixed in position, complete all as specified in ssr part i and as directed.note: pvc tank shall be isi marked and having three layers. 109 s&f in position rotational moulded polyethylene water storage tanks 1000 lts capacity, white colour ( cylinderical verticalwith closed top ) hoisted and fixed in position, complete all as specified in ssr part i and as directed.note: pvc tank shall be isi marked and having three layers. 110 s&f of 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed. 111 s&f in renewal of 20 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed. 112 s&f in renewal of 15 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed. 113 s&f in renewal of stop valve 15 mm nominal bore, cast copper alloy, fancy type, chromium plated with long shank and cup ( concealed type ) , screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to gi socket complete all as specified and directed. 114 s&f in renewal of bib taps, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handles, screwed down, screwed for 15 mm bore gi pipe or for brass ferrule orto gi socket complete all as specified and directed. 115 s&f in renewal of angle valve 15 mm bore cast copper alloy, cp, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed, complete all as specified and directed. 116 s&f in renewal of two way angle valve 15 mm bore, cast copper alloy, chromium plated with long shank and cup ( concealed type ) , screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to gi socket complete all as specified and directed. 117 s&f in renewal of kitchen sink mixer cp hot & cold, 15mm bore, bright finish with three joints screwed the ends for iron pipe and plugging etc completeall as specified and directed. 118 s&f in renewal of wall mixer fitting with built in non return valve with 3 in 1 wall mixer, chromium plated brass, fancy type for 15mm bore completeall as specified and directed. 119 s&f in renewal of basin mixture cp hot & cold, 15mm bore, bright finish with three joints screwed the ends for iron pipe and plugging etc completeall as specified and directed. 120 s&f in renewal of vitreous china floor mounted water closet pan ( pedestal pattern ) with & including superior quality dual type low level pvc flushing cistern, water jet spray and health faucet & including connection to drain or out going pipe and to flushing pipe, antisyphonage pipe etc., & including plastic seat cover white with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and directed. 121 s&f in renewal of vitreous china squatting pan orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed. 122 s&f in renewal of 10 ltr capacity pvc low level flushing cistern, top push type with inlet ball valve, pvc float, brackets & including superior quality pvc flush pipe of 32 mm dia, completeall as specified and directed. 123 s&f in renewal of sink with draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality pvc waste pipe and connecting union to pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm fixed on granite stone slab and top of granite stone match with top of kitchen sink complete all as specified and directed. note : granite stone slab shall be measured and paid in separately with appropriate item of boq. 124 s&f in renewal of sink with draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality pvc waste pipe and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed. 125 s&f in renewal of stainless steel utensil plate rack of size 900 x 600 x 200 mm, made of 0.60 mm thick stainless steel sheet and fixed in position, design and pattern as approved by the ge, complete all as specified and directed. 126 s&f in renewal of 600x450 mm bevelled edge mirror 5.5 6mm thick selected quality glass flaw less, mounted in 6 mm thick ac buildings board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 127 s&f in renewal of ptmt alloy toilet cabinet with mirror of overall size 350x450 mm and fixed to wall complete all as specified and directed. 128 s&f in renewal of soap dish fancy type, chromium plated, approx size 160x160x90mm, fixed to plugs with chromium plated brass screws etc, complete all as specified and directed. 129 s&f in renewal of toilet paper holder, chromium plated, fixed to plugs with chromium plated brass screws etc, complete all as specified and directed. 130 s&f in renewal of 300 mm corner glass shelf with abs brackets etc, complete all as specified and directed. 131 s&f in renewal of grating doom of 100 mm dia, made of mild steel chromium plated, complete all as specified and directed. 132 s&f in renewal of pvc ( swr ) 75 mm dia floor trap, with cp grating including jointing to waste pipe and fixed in cement concrete 1:2:4 type b1 ( using 20 mm graded stone aggregate ) complete all as specified and directed. 133 s&f in renewal of salt glazed stoneware gully traps of size 150x150, square or round mouthed, type p complete all as specified and directed. 134 s&f in renewal of 100mm cast iron sanitary connection socket to fit wc out let complete all as specified and directed. 135 s&f pvc ( swr ) pipe 75 mm bore, single socketed, in any length with rubber ring joints laid in trenches or in floor and including dismantling of old u / s existing pipes alongwith fittings and accessories complete all as specified and directed. 136 s&f pvc ( swr ) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to walls and including dismantling of old u / s existing pipes alongwith fittings and accessories complete all as specified and directed. 137 s&f pvc ( swr ) pipe 75 mm bore, single socketed, in any length with rubber ring joints and fixed to walls and including dismantling of old u / s existing pipes alongwith fittings and accessories complete all as specified and directed. 138 s&f pvc ( swr ) bend 75 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed. 139 s&f pvc ( swr ) bend 110 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed. 140 s&f pvc ( swr ) 110 mm bore junction single, ( single t ) equal or unequal with oval access door, incl jointing to waste pipe with solvent cement, complete all as specified and directed. 141 s&f pvc ( swr ) 75 mm bore junction single, ( single t ) equal or unequal with oval access door, incl jointing to waste pipe with solvent cement, complete all as specified and directed. 142 s&f pvc ( swr ) vent cowl 110 mm dia, incl jointing to waste pipe with solvent cement, complete all as specified and directed. 143 s&f stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, dia of pipe 100 / 110 mm, complete all as specified and directed. 144 s&f stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, dia of pipe 75 / 80 mm, complete all as specified and directed. 145 demolition and breaking up drain pipes 150mm dia ( salt glazed ware, ac or reinforced concrete ) set in cement mortar complete all as specified and directed. 146 m&l for cement concrete 1:4:8 type d 2 using 40mm graded stone aggregate as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, for 150mm bore of pipe complete all as specified and directed. 147 m&l 150 mm bore reinforced concrete pipes, class np2, laid to slope in trenches and jointed in cm 1:1 and tested, complete all as specified and directed. 148 excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying cables etc not exc 10 sqm on plan and getting out in soft / loose soil, complete all as specified and directed. 149 returning filling in excavated soil including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as specified and directed. 150 removing excavated materials ( soil ) not exc 50 m distance and depositing where directed at a level not exc 1.5 m above the starting point, complete all as specified and directed. 151 taking down carefully copper / aluminium point wiring ( light, fan, socket or power ) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed. 152 dismantling unserviceable main switch / dbs incl wooden board and deposit to mes store yard including making good disturbed surface of wall complete all as specified and directed. 153 taking down sub main wiring of any size / capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed. 154 m&l for point wiring with pvc insulated ( frls ) unsheathed multi stranded copper conductor cable of size 1.5 sqmm with pvc insulated ( frls ) unsheathed multi stranded copper conductor cable of size 1.5 sqmm as earth continuity wire to be drawn in and including pvc concealed conduit not less than 20 mm dia including with all accessories and fittings, fixed in concealed & including providing ms sheet metal sunken switch / terminal box 1.2mm thick for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surfaces, complete allas specified and directed for the following: one light / ceiling fan / exhaust fan / bell buzzer point controlled by one, one way switch of 5 / 6 amps.note : cutting chases and making good to match with the adjoining surface deemed to be included in the unit quoted rate. 155 all as per item no 153.00 ( here in before ) but one 5 pin, 5 / 6 amps socket outlet point on independent board, controlled by one, one way 5 / 6 amp switch. 156 all as per item no 153.00 ( here in before ) but one 5 pin, 5 / 6 amps socket outlet point on same board, controlled by one, one way 5 / 6 amp switch. 157 all as per item no 153.00 ( here in before ) but one light point controlled by two, two way switch of 5 / 6 amps. 158 m&l point wiring with pvc insulated ( frls ) unsheathed multi stranded copper conductor cable of size 2.5 sqmm, with pvc insulated ( frls ) unsheathed multi stranded copper conductor cablefrls of size 2.5 sqmm as earth continuity wire to be drawn in and including pvc concealed conduit not less than 20 mm dia including with all accessories and fittings, fixed in concealed for one socket outlet 15 amp on independent board & including providing ms sheet metal sunken switch / terminal box 1.2mm thick and fittings for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surface, complete all as specified and directed.note : cutting chases and making good to match with the adjoining surface deemed to be included in the unit quoted rate. 159 s&f modular switch 1 way 5 / 6 amps, 1 module, 240 volts, isi marked, complete all as specified & directed. 160 s&f modular switch 1 way 15 / 16 amps, 1 module, 240 volts, isi marked, complete all as specified & directed. 161 s&f modular socket, 5 / 6 amps, 2 / 3 pin combined 2 module, 240 volts, isi marked, complete all as specified & directed. 162 s&f modular socket, 6a / 16a amps, 2 / 3 pin combined 2 module, 240 volts, isi marked, complete all as specified & directed. 163 s&f modular bell push, 5 / 6 amps, 1 module, 240 volts, isi marked, complete all as specified & directed. 164 s&f in renewal of modular fan step regulator, 120w 2 module, complete all as specified & directed. 165 s&f in renewal of buzzer, ding dong ac. 230 volts, single pole complete all as specified and directed. 166 s&f in renewal of modular metal flush box 8 module, isi marked, complete all as specified & directed. 167 s&f in renewal of modular metal flush box 6 module, isi marked, complete all as specified & directed. 168 s&f in renewal of modular metal flush box 3 module, isi marked, complete all as specified & directed. 169 s&f in renewal of modular metal flush box 1 / 2 module, isi marked, complete all as specified & directed. 170 s&f modular white cover plate with frame, 8 module, isi marked, complete all as specified & directed. 171 s&f modular white cover plate with frame, 6 module, isi marked, complete all as specified & directed. 172 s&f modular white cover plate with frame, 3 module, isi marked, complete all as specified & directed. 173 s&f modular white cover plate with frame, 2 module, isi marked, complete all as specified & directed. 174 s&f modular white cover plate with frame, 1 module, isi marked, complete all as specified & directed. 175 s&f switch piano flush type 5 / 6amps, 230 volts, single pole, one way, isi marked, complete all as specified & directed. 176 s&f switch piano flush type 5 / 6amps, 230 volts, single pole, two way, isi marked, complete all as specified & directed. 177 supply and fixingswitch socket combination, 5 / 6 and 15 / 16amps, 230 volt, multi pin, flush type universal, complete all as specified and directed. 178 supply and fixing socket outlet, 5 / 6 amps, 230 volt, five pin, flush type universal, complete all as specified and directed. 179 s&f pvc / polycarbonate lamp holder, angular / batten type with back plate, isi marked complete all as specified & directed. 180 s&f in renewal of stepped type electronic fan regulator, flush type, 230 volts ac, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed. 181 s&f ceiling rose surface type pvc / polycarbonate isolated body, 65x 50mm, 3 terminals, complete all as specified & directed. 182 s&f in renewal of wall mounted 20 watt led tube light fittings, 4 feet in length, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed. 183 s&f in renewal of wall mounted 10 watt led tube light fittings, 2 feet in length, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed. 184 s&f in renewal of led street light fitting 35 watt 230 v ac outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65 / 66 protection, complete all as specified and directed. 185 m & l in renewal of street / road light gi mounting bracket made out of steel tube, medium grade, 32 mm dia ( or higher size to suit the opening of the fitting ) 0.550 mtr long by hydraulic pressed mechine bend to require arc shape and fixed to pole with 02 nos ms flat iron clamps of suitable size fixed with bolts, nuts and washers including drilling holes and grouting with the same for fixing bolts as required & incl duly painted with two coat of aluminum paint over a coat of aluminum red oxide primer and fixing with lights fittings on the existing old street light poles complete all as specified and directed. note : cost of necessary tools and plants such as ladders, hydra for renewal of mounting brackets, light fittings, nuts, bolts etc shall be deemed to be included in the unit rate quoted. 186 s&f mcb, 6 to 32 amps, single pole, 240 volt, 10 ka c curve including all accessories, complete all as specified and directed. 187 s&f mcb, 40 to 63 amps, single pole & neutral, 240 volt, 10 ka c curve including all accessories, complete all as specified and directed. 188 s & f in renewal of single pole and neutral enclosure with a two pin and earth plug and socket complete with & including one single pole mcb of 20 amps complete, all as specified & directed. 189 s & f mccb 125 amps, 415 volts, four pole, c curve, adjustable type with rupturing capacity 36ka conforming to is 8828 1996, iec 60898 and testing for proper functioning complete, all as specified & directed. 190 s & f factory made verticle tpn db, 4 way, double door, ip 43, as per is 8623 iii, impact resistance ik 09 with the provision of 125 amp mccb 4 pole, 25 ka as incomer, 160 amp rated busbar, blanking plates with all electrical connection complete all as specified and directed.note for items of mcb db ( 1 ) the unit rate includes for cutting the brick / stone walls to accommodate db to make flush to wall. ( 2 ) the unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface. 191 s & f factory made mcb db made of sheet steel phosphatised, powder painted with bus bar 200 a, neutral link, earth bar and din rail, 240 volts spn with 8 ways, double door, complete all as specified and directed. 192 s & f factory made mcb db made of sheet steel phosphatised, powder painted with bus bar 200 a, neutral link, earth bar and din rail, 240 volts spn with 12 ways, double door, complete all as specified and directed. 193 s&f of concealed sub main wiring with two runs of single core pvc insulated and unsheathed frls multistranded copper conductor cable of size 10 sqmm lt, 1100 volts grade, drawn through and including 20 mm dia pvc nonmetallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 10 sqmm single core multistrandedfrls copper conductor cable green colour as earth continuity conductor, including all necessary wall cutting and making good disturbed surface complete all as specified & as directed. note for items of submain wiring: ( i ) cutting chases of stone masonary wall and making good to match with the adjoining surface deemed to be included in the unit quoted rate. ( ii ) two runs of cable one run of earth wire and one run of pvc non metallic conduit of 20mm dia shall be measured as one run length. ( iii ) cable required for connection to dbs shall deemed to be included and shall not be measured separately. ( iv ) earth wire shall run inside the pvc conduit. 194 s&f of concealed sub main wiring with two runs of single core pvc insulated and unsheathed frls multistranded copper conductor cable of size 6 sqmm lt, 1100 volts grade, drawn through and including 20 mm dia pvc nonmetallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistrandedfrls copper conductor cable green colour as earth continuity conductor, including all necessary wall cutting and making good disturbed surface complete all as specified & as directed. 195 s&f of concealed sub main wiring with two runs of single core pvc insulated and unsheathed frls multistranded copper conductor cable of size 4 sqmm lt, 1100 volts grade, drawn through and including 20 mm dia pvc nonmetallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 4 sqmm single core multistrandedfrls copper conductor cable green colour as earth continuity conductor, including all necessary wall cutting and making good disturbed surface complete all as specified & as directed. 196 m&l for earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground ( earth plate not less than 2.25 mtr below normal ground level ) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade gi tubing for protection of earth wire, ms sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 cm compacted thickness all around the electrode with concrete earth pit of pcc 1:3:6 type 75 mm thick precast rcc ( 1:2:4 ) type b1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft / loose soil and disposal of spolis to a distance not exc 50 mtr and necessary connection and testing complete all as shown in electrical plate no. 3 and including dismantling and taking out old earthing complete all as specified and directed.notes: ( a ) irrespective of whatever is shown in plate no 5 of ssr, earth pit shall be casted in pcc ( 1:3:6 ) type c 1 and precast cover of rcc ( 1:2:4 ) type b 1 with suitable handle. ( b ) item includes the cost of gi pipe for protection of earth wire and earth wire upto 7.5 m. any variation below or above shall be measured and paid for separately under relevant item of this sch ‘a’. 197 s&f in renewal of exhaust fan, steel body ac single phase. 230v of size 230mm, sweep with, blades, and frame and louvers & including connecting with and including pvc insulatedthree core 23 / .0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing mes no with black syntheticenamel paint 2.0 cm high and including making appropriate hole in the wall / window complete all as specified and directed. 198 s&f in renewal of exhaust fan, steel body ac single phase. 230v of size 300mm, sweep with, blades, and frame and louvers & including connecting with and including pvc insulatedthree core 23 / .0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing mes no with black syntheticenamel paint 2.0 cm high and including making appropriate hole in the wall / window complete all as specified and directed. 199 m & l for taking down carefully of serviceable geyser from its existing position by disconnecting all connection and keeping it in safe custody and refixing / re installation the same with nuts, bolts, fastnersand electrical connection etc., complete all as specified and directed. 200 s&f in renewal of hdpe pvc connection 600 mm long suitable for 15 mm gi pipe with two ptmt nuts and rubber washers complete all as specified and directed. 201 m & l for taking down carefully ceiling fans, exhaust fans, wall fanscomplete with blade and deposited it into mes stores & re fixing of the same to the specified locations and including connecting of ceiling rose with and including pvc insulatedthree core 23 / .0076 copper conductor cable, complete all as specified and directed....

Fci Aravali Gypsum And Mineral India Limited - Rajasthan

40867073 tender for construction of watch & ward building pandoli chittorgarh civil work as per nit; 1 laying and jointing pvc pipe. heading 2 excavation by meachanical means ( hydraulic excavator ) manualmeansoverareas ( exceeding 30 cm in depth 1.5m in widh as wellas 10sqm on plain ) including disposal of excavated earth lead up to 50 m and lift up to 1.5 m disposed earth tobe levelled and neatly dressed all kinds of soil 3 providing and layingin position cements concrete including curing compaction etc complete in specified grade excluding the cost of centering & shuttering. all work up to plinth level ( i ) using 1:4:8 stone agg. 20 mm nominal size ( ) 4 ( ii ) using1: 2 :4 stone agg 20mm nominal size ( crusher broken ) 5 random rubble stone masonry forwith hard stone in foundation and plinth in cement sand mortarabove 30 cm thick walls in c.m 1:6 foundation 6 randam rubble stone masonary with hard stone in supersture above plinth levelupto five level above 30 c.m thick wall inc.m 1:6 7 filling available excavated earth ( excluding rock ) in trenches plinth side of foundation etc. in layers not exceeding 20cm in depth consolidation each deposited layer by ramming and watering including lead up to 50mtr and with all lift 8 brick masonry with f.p.s bricks of class designation 75in super structurebove plinth level upto floor v level inall shapes and sizes in c, m .1:4 9 supplying and fixing stone lintel / bed plates of approved quarry rough dressed in cement mortar 1:4 up to 15 cm. thickqty c.o from item no 5 of deduction lintel 10 p / f steel gate grating and grill madeof angle tee square bar or other flat black pipe with holdfast and fitting complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide.40x40x6 mm 11 providing and fixinghorizontel chajja of red / white sand stone 40 mm thick and up to 80 mmprojection inthick stone chajjas in cementmortar 1:4 including pointing in white cement mortar 1:2 with an admixture of pigment matching the stone shade. 12 providing and laying in position specified grade of cemrnt concrete for r.c.c structural element upto floor five level including curing compaction , finishing with rendering in cement sand mortar 1:3 and making good the joints and cost of plastizers excluding the cost of centering , suttering and reinforcement for beams ( any thickness ) suspended floor, roofs, griders having slops up to to 15 o landing balconies, sheleves, chajjas, lintels, bands, plain windows sills stairscases, andspiral staircase etci. m20 grade nominal mix / design mix 13 centering and shuttering with ply wood or steel sheets including strutting .propping bar cling both ways with wooden members and removal of form work up to floor five level suspended floors, roofs. landing .staircasescantilever, bands, copingbed plates anchor .blocks sills , chajjas, lintel, beams etc 14 providing and fabrication reinforcement for rcc work including straightening , cutting bending , placing in position in binding ( includingcost of binding wire ) all complete up to floor five level cold twisted deformed bars ( is:1786 ) 15 providing and fixing external grade board solid core single leaf flush door shutter isi2202.67 marked using phenol for dehyersin in glu both sides with approved steel fitting complete as per annexure a i 30 mm thick: decorative teak veneer both face ch 8 item, no 8.13.2.3 page93 16 supplying and fixing fixed wire gauge of 14mesh x 24gauges to the metal frame of rolled section by metal beading 20 x 3 mm with suitable screw at not exceeding 150 mm distance. 17 ii randdom rubble dry stone kharanja under floor ch b 11 item no11.26 page no133 18 p / f 1st quality vitrified porcelainpolished dtile on floor, skirting and steps etc.in differrent sizes thickness minium 10 mm ) water absortion less than or equal 0.08% and c betile to specified bymanufacture ) with water absorition less than 0.08% and conforming to.i s 15622 of approved make in all colour and shade , laid with 20mm thick c.m 1:4 including grounting the joints with white cement and matching pigment etc.completei size600mmx600mm 19 plaster on new surface on wall in cement sand mortar1:4including racking of joints etc complete fine finish i , 25 mm thick 20 supplying and fixing in wall machine cut and polished stone shelves tends in cement mortar 1:3with machine cut edges i sand or other approved stone, 50 mm thick 21 finishing of wall with water proofing cement paint of approved brand and or required shade to give an even shade including all scaffoldng i new work ( two or more coats applied@3.84kg / 10sqmi 22 distempering with dry distemper of approved brand and shade ( two or more coats ) and of required shade on new work, over and jncluding, primering coat of whiting to give an even shade including all scaffolding ch 12 item 12.36 , page no144 23 painting with synthetic enamel paint of approved brand and manufacture to give an even shade. itwo or more coats on new work 24 p& f .p.v.c storage tank i, s, i marked ( is 12701 ) indicating the bis license no ) of approved make with cover, 25 mm dia 1m long gi over flow pipe & 25 cmlong was out pipe with plug & socket, including making connection itc. complete of approved design i 500 litres itemno2.26.3 page no 236 25 constr of septice tank forsize 200x100x130 c.m ( for 10 users ) ch s 3 iteam no3.27.1page 252.253 26 add electrical installation without ceiling fan, 5% x 27 add saintary fitting , 10%= 28 miscellaneouscharge...

North Western Railway - Rajasthan

40600480 auction sale of u/s ms release v type frame 156 nos./14.073 mt, u/s ms release v type frame 04 nos./0.267 mt, bed plate off size 52 nos./6.012 mt, release ismb 600 (rsi) girder 01 nos./1.226 mttotal = 21.578 mt1.mod by actual weight2.loading by purchaser3.cutting allowed for loading purpose...

North Western Railway - Rajasthan

39857096 auction sale of lot no. 2/sse/pw/c/mvj, stack no. 1 us ms tiebar=991nos.=7.499mt, stack no. 2 us angle with aluminium/ms board=69nos.=1.830mt, stack no. 3 g/rail 90r=252 nos.=652.54rm=25.965mt, c/rail 52kg=13nos.=28.51rm=1.260mt, c/rail 90r=153nos.=411.01rm& fp 90r=2no.=15.917mt, cluster41.25r=5 nos.=30.21rm=0.707mt, t/rail 60r=2 nos.=5.85rm=0.102mt, s/rail 50r=02 nos.=5.71rm=0.136mt, rail 50r=2 nos.=5.02rm=0.100mt, rail 60r=2 nos. =3.18 rm=0.076mt, c/rail 60r=3nos.=11.89rm=0.238mt, rail attached boards 60r=41nos.=79.08rm=2.035mt, rail attached boards 50r=70nos.=142.02rm=4.040mt, rail attached boards 75r=11nos.=41.07rm=1.540mt, us rail 41.25r=20nos.=49.35rm=1.043mt, g/rail 41.25r=19 nos.=47.70rm=0.967mt, fp offsize=1881 nos.=16.569mt, us rail 52kg de=2nos.=13.73rm=0.539mt, us rail 60r de=2nos.=21.96rm=0.572mt, ms keys=1329nos.=0.550mt, jfp offsize=81 nos.=0.772mt, comb. fp offsize=40nos.=0.258mt, screw offsize=420nos.=0.219mt, chair plate mg=43 nos.=0.272mt, fish bolt offsize=4359 nos.=3.713mt, p&c 52kg all fittings=2 set=1.617mt, ms gauge tie plate=6 nos.=0.467mt, p&c 60kg all fittings=01 set=0.832mt, bed plate=85nos.=1.405mt, msbp offsize= 786 nos.=2.176mt, dog spike=2690nos.=0.647mt, stretcher bar=12 nos.=0.202mt, rail 50r closure=19nos.=19.81rm=0.418mt, rail 60r closure=2no.=2.56rm=0.071mt, rail 90r closure=460nos.=155.11rm=6.687mt, rail 52kg closure=477nos.=113.12rm=5.614mt, rail 60kg closure=379nos.=71.36rm=4.210mt, bridge girder=1no.=7.01rm=0.885mt total lot qty.= 112.150mt; mod=actual weight....

Military Engineer Services - Rajasthan

39456813 tender for special repair of offers mess bldg at jalipa mil stn under ge ( a ) barmer ( job no 001 / sr / ( bldg ) / 12c / 23 24 / q3w ) ; 1 s&f for rolled mild steel fe 410 w ( gde e 250 ) quality a in plate girder or single stanchions, built up of one beam of channel section with flange plates, caps, bases, splices, angle brackets, cleats and other connections including with necessary butt or lap welded joint complete all as specified and directed. 2 s&f for rolled mild steel fe 410 w ( gde e 250 ) quality a in compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. including with necessary butt or lap welded joint complete all as specified and directed. 3 s&f for rolled mild steel fe 410 w ( gde e 250 ) quality a in plates ( plain or chequered ) channels. square cut or notched ( ordinary and counter sunk ) forming holes, with riveted, bolted or welded attachment including with necessary butt or lap welded joint complete all as specified and directed. 4 s&f for mild steel screw bolts ( machine made ) of 16 to 24 mm dia of neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, but length of bolt exc 22.5cm and n exc 30cm long embedded in concrete complete all as specified and directed. 5 m&l for steel work in tubular trusses, bracings including special shaped washer etc. complete using erw or induction butt welded tubes conforming to is 1161 1979 grade st. 240 complete all as specified and directed by engineer in charge. 6 m&l for preparation of new or previously untreated steel or iron surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paintover a coat of red oxide primer complete all as specified and as directed. 7 m&l for plain cement concrete 1:4:8 ( type d 2 ) using 40 mm graded crushed stone aggregate in foundations , filling and mass concreate complete all as specified and directed. 8 excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard / dense soil complete all as specified and directed. 9 excavating in trenches, n exc 1.5 m wide and exc 1.5 m in deep but n exc 3.00 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in hard / dense soil complete all as specified and directed. 10 excavation over area n exc. 1.5 m deep and getting out in hard / dense soil complete all as specified and directed. 11 removing excavated material exc. 1.50 km but n exc.5 km complete all as specified and directed. 12 returning filling in including spreading levelling watering and well ramming in layers n.exc 25 cm in soil. 13 formwork to sides rough finished surfaces of concrete of pillars, posts, struts, piers, columns, and stanchions ( leak proof ) complete all as specified and directed by engineer in charge. 14 formwork to flat rough finished surfaces of soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) ( leak proof ) complete all as specified and directed. 15 formwork to rough finished surfaces edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. 16 s&f for mild steel tmt bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 17 s&f for mild steel tmt bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 18 s&f for mild steel tmt bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 19 m&l for chipping of 50mm average thickness unsound / weak concrete material from slabs, beams, columns, footings etc. with manual chisel and / or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts complete all as specified and directed. 20 m&l for cleaning & applying rust remover on ( cico clean o rust ) in two coats over rusted reinforcement surface of rcc membersand providing anti corrosive coating with two component epoxy based zinc rich primer / rust passivation inhibitor coat at the rate of 2 3 sq. mtr / ltr not less than 50 microns dft with cico zincilate 500 or equivalent to reinforcement surface as per manufacturer’s instructions including all machinery, tools tackles and clearing of debris. make: cico clean o rust, cico zincilate 500 or equivalent in fosroc / dr fixit / acc / l&t / stp. ( note : entire surface of rcc members shall be measured. ) 21 s&f of new steel or rebars by drilling holes with 10 mm to 25mm dia and 100 to 200mm deep as per is code of 10d formula and filling the holes after inserting of reinforcement dia 8 to 16mm for anchoring at ends / shear connector and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy acrylate fixing and anchoring compound ( having the technical parameters mentioned in material specifications ) using standard sealant applicator gun after drilling holes of required diameter at required locations, for holding / fixing / placing in position the steel mesh reinforcement at desired level / stretching. ( note : steel / reinforcement shall be paid and measured separately ) .make: cico resifix g or equivalent in fosroc lokfix / hilti and master builder ( basf ) 22 m&l for providing micro concrete m 50 ( minimum grade ) with cico microcrete at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine, including all necessary scafolding if required etc all as specified and directed.make: cico microcrete of cico technologies ltd or equivalent in fosroc / stp / basf. 23 m&l for epoxy bonding agent suitable for bonding new to old concrete, bricks and steel components, bricks, tiles etc after the prepration of old concrete / rcc surface by cleaning and removing of dust, dirt, loose particles, laitance etc by wire brushing, scrapping and washing with water complete all as per manufacturers instructions. 24 demolition of brickwork of stone / boulder masonry, build in cement mortar including all for ashlars facings, dressed stonework, precast concrete articles and precast concrete block walling complete all as specified and directed. 25 m&l for pre cast cement concrete block masonry with solid blocks, 1:3:6, type c 1 ( using 20 mm graded aggregate ) exc. 10 cm in width and setting in cement mortar ( 1:6 ) , complete all as specified and directed. 26 taking down cement plaster of any description, any thickness from surfaces of walls / soffits of roof projections & chajjas / ceilings etc. incl raking out joints, hacking for keys, scrubbibg down with water etc complete all as specified and directed. 27 m&l for rendering 15mm thick in cm ( 1:6 ) on fair faces of brick work or concrete surfaces even and fair finish without using extra cement complete all as specified and directed. 28 m&l for 3mm thick wall care putty on wall complete all as specified and directed. 29 m&l for preparing new plastered or unplastered surfaces of walls, and applying two coats of oil emulsion distempering over a coat of interior wall primer complete all as specified and directed. 30 m&l for rendering 15mm thick in cm ( 1:4 ) on fair faces of brick work or concrete surfaces even and fair finish without using extra cement mixed with wpc as per manufacturers instructions complete all as specified and directed. 31 m&l for preparation of new plastered surfaces of walls and applying two coat of cement based paint over a coat of primer complete all as specified and directed. 32 supply only integral liquid water proofing compound complete all as specified & as directed. 33 demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, cills, aprons etc complete all as specified and directed. 34 m&l for virified ceramic tiles ( dark shed ) 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cm ( 1:4 ) complete all as specified and directed. 35 m&l for virified ceramic tiles ( dark shed ) 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick backing coat in cm ( 1:4 ) complete all as specified and directed. 36 m&l for machine cut kota stone slab cills 20 25mm thick over cement screed bed 15mm thick in cm ( 1:4 ) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab inclunding rubbing and polishing complete all as specified and as directed. 37 demolition of cement concrete ( unreinforced ) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 38 m&l for 25mm thick pcc 1:2:4 type b 0 ( using 12.5mm graded stone aggregate ) as in levelling course in floor complete all as specified and directed. 39 m&l for 75 mm thick pcc 1:3:6 type c 1 ( using 20mm graded stone aggregate ) as in plinth protection including making joint at every 3mtr interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and directed. 40 taking down chowkhats or frames ( without taking off shutters from the frame ) exc 1.5 sqm and n. exc 4.00 sqm incl cutting holesand making good reqd shape for hold fast block for new frame complete all as specified and directed. 41 s&f for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. 42 s&f for anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long ( 1 no. ) . hinges type b 21 100mm long ( 2 no. ) suitable handle ( 1 no. ) complete all as specified and as directed. 43 s&f for anodised aluminium door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 nos in each door, hinges, anodised aluminum snap beading screws etc. ccomplete all as specified and as directed. 44 s&f for aluminium ( die cast ) body door closer hydraulically regulated, designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed. 45 m&l for 4.8mm thick sheet glass, ordinary quality and fixed with glazing clips, rubber packing in square in n exc 0.5 sq.m in each pane in each pane complete all as specified and as directed. 46 s&f for stainless steel wire cloth 0.36mm nominal dia of wire andaverage width of aperture 1.40mm and fixed with stainless steel wire stapples complete all as specified and as directed. 47 s&f for 25mm thick pre formed filler for expansion joints including dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed. 48 s&f for heavy duty false work of any height like composite steel section erecting for temporary supports with adjustable arrangement to the structural members like beams, columns, slabs in horozointal or vertical directions etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work and removed after work complete as per the instruction of engineer in charge. note: these supports shall be provided either in the form of props or trestles fabricated using structural steel as per the site requirements complete and all as specified & directed. 49 s&f for ms props of any height, erecting for temporary supports with adjustable arrangement to the structural members like beams, columns, slabs in vertical directions etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work and removed after work complete as per the instruction of engineer in charge. note : these supports shall be provided either in the form of props or trestles fabricated using structural steel as per the site requirements complete and all as specified & directed. 50 s&f for 150mm bore of pvc ( swr ) perforated pipes with 10mm dia perforation holes single socketed in any length with rubber ring joints laid laid in trenches or in floors complete all as specified and as directed. 51 s&f for 150mm bore of pvc ( swr ) pipes single socketed in any length with rubber ring joints laid laid in trenches or in floors complete all as specified and as directed. 52 supply only 20mm nominal size graded coarse aggregate as in trenches around the pvc perforated pipe complete all as specified and as directed. 53 m&l for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed. 54 demolition of cement concrete ( reinforced ) of any description and in any position not otherwise specifically provided for complete all as specified and as directed. 55 m&l for reinforced cement concrete ( design mix ) m 25 ( 20mm graded stone aggregate ) inbeams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by engineer in charge. 56 m&l for reinforced cement concrete ( design mix ) m 25 ( 20mm graded stone aggregate ) incolumns, pillars, piers, posts and struts complete all as specified and directed by engineer in charge. 57 m&l for reinforced cement concrete ( design mix ) m 25 ( 20mm graded stone aggregate ) inslabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, chajjas and in shelves and the like complete all as specified and directed. 58 m&l for reinforced cement concrete ( design mix ) m 25 ( 20mm graded stone aggregate ) infoundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed. 59 m&l for reinforced cement concrete ( design mix ) m 25 ( 20mm graded stone aggregate ) inwalls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed. 60 formwork to sides of flat rough finished surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. 61 formwork to sides of flat rough finished surfaces of concret to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and directed. 62 m&l for plain cement concrete, 1:2:4, type b 1 ( using 20 mm graded crushed stone aggregate ) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. 63 m&l for providing precast cement concrete, 1:2:4, type b 1 ( using 20 mm graded crushed stone aggregate ) in landings, cover slabs ( for manholes etc. ) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and setting in cm ( 1:4 ) with joints to match complete all as specified and directed. 64 m&l for soil stabilization of 150 mm sub grade soil by uniform mixing of cement opc 43 grade / lime / other additive@ 5% cement by weight of soil ( percentage of cement / additives for estimation purposes only type of additive and, percentage required fo blending to be given in mix design ) . item will include pulverization of soil, spreading of additive, blending mix by tractor towed rotovator, addition of water / drying of mix to required moisture content and compaction using suitable vibratory roller to required 95% maximum dry density. provisions of irc sp:89 2010 be referred to for this item 65 m&l for hardcore broken stone / boulder of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled / rammed to a true surface complete all as specified and directed. 66 m&l for complete removal of existing treatment, plastered or unplastered old surfaces of ceiling, including filling of cracks / holes by crack filler, removing unnecessary nails and applying three coats of white wash complete all as specified and directed. 67 m&l for complete removal of existing treatment, plastered or unplastered old surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails applying two coats of oil bound distemper / emulsionover a coat of interior wall primer over 3mm thick wall care putty complete all as specified and directed. 68 m&l for preparing old plastered or unplastered surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails and applying two coats cement based paint complete all as specified and directed. 69 note: ( i ) retrofitting / rehabilitation work shall be executed with / under supervision of specialised agency, charges of specialised agency supervision to be borne by the contractor during the execution of the work as specified and directed. ( ii ) contractor have to get approval of applicator or authorized agency by submitting its authorization letter to this office for approval of accepting officer prior to commencement of work. ( iii ) name of specialised agency : cico resifix g or equivalent in fosroc lokfix and master builder ( basf ) ] ...

Water Resources Department - Rajasthan

38789579 necessary irrigation work in gagrin medium irrigation projects tehsil pirawa district jhalawar , item description , planning and designing collection of revenue map and jamabandi of the area of interest, scanning revenue map and digitization of khasra boundaryandjamabandi. rate shall be paid per ha gca , planning and designing geo refrencing of digitized khasra map and marking chakandsub chak of required size for micro irrigation and providing chakandsub chak wise gca, cca details in excel format. soft copy with two set of hard copy shall be provided. rate shall be paid per ha cca , planning and designing planning of field distribution pipe network up to chak and sub chak level, hydraulic design of pipe network planninganddesign of outlet arrangement with drawing and irrigation scheduling up to chak level. chak plan showing pipe network is to be provided in soft copyandtwo set of hard copy. rate shall be paid per ha cca , planning and designing preparation of l section of pipe lines as per approved pipe networkandhydraulic design from competent authority (showing safety valveandcontrol valve arrangement, filteration system and other accessory if required). design and drawing of thrust blocks, pedestals and valve chamber, are to be provided. all design, drawing should fulfill the design specification as per the tender document and is code / relevant mannuals. rate shall be paid per ha cca , planning and designing irrigation scheduling with timing up to subchak level is to be preapred as per approved design and revenue record. rate shall be paid per ha cca , planning and designing planning and design of diggie for micro irrigation system including design of intake/ sump well, pump house and other ancillary developments to be done in the campus and providing all hydro electro mechanical designs and drawings. , for new work survey work in a grid at defined interval using total station / dgps instrument and preparation of block level plan showing all permanent features/ utilities including trees, for planning of dam/ canal / water course / pipe network alignment and superimposing it on digitalized sajra map and developing contours at interval desired by engineer incharge. block level plan is to be submitted in hard copy three set and soft copy in auto cad format, using layer system, showing all features. note: khasra map will be provided by department in plain area block level to be taken @ 30 meter grid , part a : earth work in excavation excavation including loading, unloading, disposal and dressing of excavated earth within initial lead of 50m and lift up to 1.5m including dressing of excavated area and dewatering wherever required complete in all respect 2.hard / dense soil , part a : earth work in excavation excavation including loading, unloading, disposal and dressing of excavated earth within initial lead of 50m and lift up to 1.5m including dressing of excavated area and dewatering wherever required complete in all respect 3.hard soil mixed with kankar / boulders, morrum , part a : earth work in excavation excavation including loading unloading disposal and dressing of excavated rock within initial lead of 50m and lift upto 1.5m in dry or moist including dressing of excavated area, de watering wherever required complete in all respect. 1.soft / disintegrated rock , part a : earth work in excavation earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of engineer for following depths, below natural ground / road top level. 1.in all types soils/ saturated soil such as morrum, sand, sandy silt, clay, black cotton soil, kankar, etc. i) depth upto 1.5 m , part a concrete work providing and laying in position of cement concrete nominal mix (1:3:6) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3(1 cement : 3 coarse sand) and making good the joints excludingthe cost of centering, shuttering and reinforcement. well graded crusherbroken stone aggregate of maximum size upto; 20mm , part a concrete work providing and laying in position of cement concrete nominal mix (1:3:6) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3(1 cement : 3 coarse sand) and making good the joints excludingthe cost of centering, shuttering and reinforcement. well graded crusherbroken stone aggregate of maximum size upto; 40mm , part a concrete work providing and laying in position of cement concrete nominal mix (1:1.5:3) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3(1 cement : 3 coarse sand) and making good the joints excludingthe cost of centering, shuttering and reinforcement. well graded crusherbroken stone aggregate of maximum size upto; 20mm , side shuttering including propping etc. complete (to achieve finish f 2 for : 2.top or intermediate bed plates, in between masonry or piers, abutments sluice wells etc. , side shuttering including propping etc. complete (to achieve finish f 2 for : retaining wall, counterfort, abutment, wing walls up stream or down stream slope facings of dams and open faces of construction joints etc. , part b canal lining providing and laying cns (cohesive non swelling) selected soil (from any source including private fields) and laying in layers below pcc block cc lining in layers of 15 20 cm watering and compaction to achieve a density of 95 percent of standard proctors density including all leadandlift, dewatering whenever necessary and complete as per technical specifications. thickness of and specification of cns should confirm to is:9451 latest revision. , 2.supplying of m.s. reionforcement including labour charges for bending binding and placing in position all reinforcement as per drawing including cost of binding wire and all leads and lifts using. tor or ribbed bars (is :1786 1985) , field distribution pipe network water allowance has been taken 3.0 cusec / 1000 acre supplying, laying, jointing, testing and commissioning of buried hdpe pe 100 grade pipe net work system in the chak upto hydrant (chak size up to 200 ha and sub chak with hydrant at every 4.0 ha to 5.0 ha) including fittings as per approved designanddrawings and fulfilling is code / mannuals specification. this item is for water allowance @ 3 cusec / 1000 acre and pipe line terminating at hydrant is to be designed to carry minimum 3.75 lps discharge and head 22 meter. the rates are inclusive of material, leadandlift and also inclusive of all kind of taxes, levies, turnover tax, service tax, octroi, vat, panchayat tax, royalty, gstand contractor profit. note: this is including cost of supplyandfixing of manual operated hydrant outlet assembly as per the respective item, but excluding cost of safety valves, control valves and metering arrangements. , 1.6 manufacturing, supplying ,lowering, laying and jointing in position to correct line spirally welded saw/fabricated ms pipe having bevelled end plates / coils, confirming to is 3589 2001 or its latest revision/ amendments, for following thickness and inside diameter, including all taxes (central and local), transportation and freight charges, inspection charges, loading/ unloading charges,including cost of labour and material, specials (tee, bend etc.), field joints,satisfactory hydraulic testing, disinfection, commissioning etc. completeas per technical specifications anddirection of engineer in charge; (excluding earthwork, internal lining and outer coating). note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately. 1.6.3outer dia of pipe 323.9 mm and thickness 1.6.3.35.6 mm , note for estimation of different component of micro irrigation work turnkey project on epc mode following provision can be considered as per design /specification finalised for the scheme. cost of hydro electro mechanical works including pumps motors, mud pumps, trash rack, screens, all valve arrangement, flow / pressure meter, water level recorder, control panel within the pump house and supply and installation of transformer (with one standby) etc. can be taken @ rs 25000 per kw of capacity of total pumps (including standby capacity). this is excluding the cost of electric transmission line from gss / grid to the pump house. , part c brick masonry brick masonry (using well burnt clay bricks of size 230x 110x 70 mm, class designation 75 as per specification) up to plinth including all leads of all construction materials including curing etc. complete. 1.in cement sand mortar 1:3 , cement plaster plaster in cement sand mortar 1:3 including racking of joints, smooth finishingandcuring etc. complete including all leads of all construction materialsof thickness: 12mm , 8.1 construction of pump house of brick/ stone masonry of required size suitable for installation of maximum 4 no. monoblock pump sets as per approved ga drawing, scope of work and technical specification complete work in all respect including electrical works for lighting and fans, rain water drainage. the plinth area of pump house shall be area of measurement. , skilled mason/ painter/ carpenter/ electrician /black smith / plumber grade i , unskilled beldar/ coolie / chowkidar / water man / earth dresser , skilled welder/fitter/line man/turner/wireman/driller , semi skilled munshi/survey amin/ density observer/ record keeper/time keeper/ gate keeper/ core observer/ laboratory assistant / gauge reader / telephone assistant grade i , skilled driver for pumps/concrete mixers...

Panchayat Raj Department - Rajasthan

37787272 construction of room of govt school in gp bibasar , earth work in excavation and disposal of surplus excavated soil as directed with in a lead of 50 meter , pcc in foundation :providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8 ( 1 cement:4 coarse sand :8 graded stone aggregate 40 mm nominal size ) . , random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in cement mortat 1:6 ( 1 cement: 6 sand ) , plinth beam: providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix , supply & stacking good earth at site complete including loading , unloading and transportation etc &filling available excavated earth ( excluding rock ) in trenches plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead upto 50 mtr. and lift upto 1.5 mtr. lead 1 km , brick masonary in1:6 ( 1 cement:6 coarse sand ) in superstructure , stone kharanja: random rubble dry stone kharanja under floor , pcc:providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level1:4:8 ( 1 cement:4 coarse sand :8 graded stone aggregate 20 mm nominal size ) .m 10 grade nominal mix , lintel beam : providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix , slab & beams: providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix , providing and laying in position specified grade of cement concrete for rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement:3 coarse sand ) and making good the joints and cost of plastisers ( if required ) excluding the cost of centtering shuttering and reinforcement, m 20 grade nominal mix / design mix. , columns : providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix , centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for :suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchorblocks, sills, chhajjas, lintel, beam, plinth beam etc. , column footing; centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for foundation, footings, strap beam, raft, base of column etc , column : centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for columns, pillers, posts, and struts etc , steel: p / f reinforcement for rcc work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete upto floor five leve tmt bars ( conforming of relevent is code ) . , ?????? ???? ( ???? ???? ) ?? 40x40x3 ???? ?? ????? ???? ??? 22 ??? ?? ???? ??.??. ????? ?? 2 ?????? ???? ?????? 25x25x3 ???? ?? ?????? ???? ?? ???? ( ????? ) ??? ??????? ???? ??? ????? ?? ????? ?????????? ??????, ?????? ??? ???? ???????? ??? ?????? ???? , ?????? ???? ( ???? ???? ) ?? 25x25x3 ???? ?? ???? ( ????? ) ??? 22 ??? ?? ???? ????? ?? 2 ?????? ???? ?????? ?? ??????? ???? ??? ????? ?? 10 ???? ?????, 3 ????. ????? ? ????? ?????????? ??????, ?????? ??? ???? ???????? ??? ?????? ???? , wire gauge supplying & fixing fixed wire gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 14 mesh x 24 gauge , kota stone slab flooring 25 mm thick over 20mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement: 4 course sand ) for area 2001 to 5000 sq. cm , kota stone slabs 20 mm thick in risers and stepsskirting, dado and pillars laid on 12 mm ( average ) thick cement mortar 1:3 ( 1 cement: 3 course sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs , including rubbing and polishing completefor areaof each slab upto900 sq.cm , external plaster : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished 20 mm thick , external plaster : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished 20 mm thick , plaster ( ceiling ) : 6 mm thick cement plaster to ceiling of mix 1:3 ( 1 cement: 3 fine sand ) , internal finishing: distempering with oil bound washeble distemper of approved brand and manufacture to give an even shade including all scaffolding new work ( two or more coats ) over and including scrapping and priming coat with cement primer , exterior finishing : wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. , panting on doors & windows: painting enamel paint of approved brand and manufacture in all shade to give an even shade , p&f rigid pvc pipe 110 mm dia , light fitting , add contigency...

Panchayat Raj Department - Rajasthan

37787271 construction of room of sahid hanumansingh govt school gp bibasar , earth work in excavation and disposal of surplus excavated soil as directed with in a lead of 50 meter , pcc in foundation :providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8 ( 1 cement:4 coarse sand :8 graded stone aggregate 40 mm nominal size ) . , random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in cement mortat 1:6 ( 1 cement: 6 sand ) , plinth beam: providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix , supply & stacking good earth at site complete including loading , unloading and transportation etc &filling available excavated earth ( excluding rock ) in trenches plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead upto 50 mtr. and lift upto 1.5 mtr. lead 1 km , brick masonary in1:6 ( 1 cement:6 coarse sand ) in superstructure , stone kharanja: random rubble dry stone kharanja under floor , pcc:providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level1:4:8 ( 1 cement:4 coarse sand :8 graded stone aggregate 20 mm nominal size ) .m 10 grade nominal mix , lintel beam : providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix , slab & beams: providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix , providing and laying in position specified grade of cement concrete for rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement:3 coarse sand ) and making good the joints and cost of plastisers ( if required ) excluding the cost of centtering shuttering and reinforcement, m 20 grade nominal mix / design mix. , columns : providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix , centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for :suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchorblocks, sills, chhajjas, lintel, beam, plinth beam etc. , column : centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for columns, pillers, posts, and struts etc , column : centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for columns, pillers, posts, and struts etc , steel: p / f reinforcement for rcc work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete upto floor five leve tmt bars ( conforming of relevent is code ) . , ?????? ???? ( ???? ???? ) ?? 40x40x3 ???? ?? ????? ???? ??? 22 ??? ?? ???? ??.??. ????? ?? 2 ?????? ???? ?????? 25x25x3 ???? ?? ?????? ???? ?? ???? ( ????? ) ??? ??????? ???? ??? ????? ?? ????? ?????????? ??????, ?????? ??? ???? ???????? ??? ?????? ???? , ?????? ???? ( ???? ???? ) ?? 25x25x3 ???? ?? ???? ( ????? ) ??? 22 ??? ?? ???? ????? ?? 2 ?????? ???? ?????? ?? ??????? ???? ??? ????? ?? 10 ???? ?????, 3 ????. ????? ? ????? ?????????? ??????, ?????? ??? ???? ???????? ??? ?????? ???? , wire gauge supplying & fixing fixed wire gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 14 mesh x 24 gauge , kota stone slab flooring 25 mm thick over 20mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement: 4 course sand ) for area 2001 to 5000 sq. cm , kota stone slabs 20 mm thick in risers and stepsskirting, dado and pillars laid on 12 mm ( average ) thick cement mortar 1:3 ( 1 cement: 3 course sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs , including rubbing and polishing completefor areaof each slab upto900 sq.cm , internal plaster : plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finish: 12 mm thick , external plaster : plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished 20 mm thick , plaster ( ceiling ) : 6 mm thick cement plaster to ceiling of mix 1:3 ( 1 cement: 3 fine sand ) , internal finishing: distempering with oil bound washeble distemper of approved brand and manufacture to give an even shade including all scaffolding new work ( two or more coats ) over and including scrapping and priming coat with cement primer , exterior finishing : wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. , panting on doors & windows: painting enamel paint of approved brand and manufacture in all shade to give an even shade , providing and laying of 50mm thick cc using mix 1.2.4 using 12mm size stone aggregate , p / l of tiles pieces for roof treatment on 25mm thick 1.4 cement sand mortar , p / f ring pvc pipe 110mm dia , light fitting , add contigency...

Public Works Department - Rajasthan

36505422 tender for supply installation testing commissioning of fire detection and fire fighting system work in simulator block and firing rang for ncc campus jln marg jaipur supplying, installation, testing & commissioning ofelectrical driven fire fighting duty terrace pump as per tac andis 12469 1988., factory assembledin pump make oemsuitable for automatic operation and consisting of following details given asa, b, c, d, e, f, g and h. 2 ( a ) horizontal end suction centrifugal back pull type pump complete for delivery of below mentioned discharge and head 3 ( b ) material of construction : pump casing cast iron, impellor bronze, shaft ss 410, packing mechanical seal 4 ( c ) squirrel cage induction motor ( ie 3 class ) suitable for 3 phase, 415 v, 50 hz, ac supply , class f insulation, synchronous speed not exceeding 3000 rpm, t.e.f.c confirming to ip:55 , of required hp suitable for the above pump , along with flexible ( love joy type ) coupling , coupling guard complete in all respect . 5 ( d ) common bed plate fabricated frommild steel channel for installation of pump and motor including anti vibration pads. 6 ( e ) the hydrostatic tests ( 2 times of design operating head or 1.5 times the shut off head whichever is higher ) and performance tests ( to determine developed head, pump bhp and efficiency v / s flow ) of pumps along with trip test shall be carried out at manufacturer’s works in virtual / physical presence of department’s representatives. 7 ( f ) physical & chemical test reports of i ) pump casing ( ii ) impeller ( iii ) shaft ( iv ) shaft sleeveand dynamic balance certificate is to be submitted by oem 8 ( g ) suitable size reinforced cementconcreat ( m 30 ) foundation with foundation bolt, nozing angle of size 40mm x40mm x5 mm ( cost of rcc foundation to be paid extra ) 9 ( h ) weather proof hood fabricated from 5mm thick uv stablised frp sheet supported by 50 mm x 50 mm x 5 mm angle iron fram above pumpset to protect it from weather all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 10 900 lpm with 35 mtr head 11 providing, fixing, jointing, testing & commissioning of heavy duty ms c class ( heavy ) pipes conforming to is 3589 / 1239 part i for hydrant and sprinkler applicationsincluding cutting, screwing, welding etc. & forged steel fittings like elbows, tees, tapers, reducer, gaskets etc. fixing the pipe on the wall / ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick or rcc walls / slab and making good the same. complete with painting of one coats of red oxide and two or more coats of synthetic enamel paint of requiredshade complete as required. ( pipe to be tested @ 10kgf / sqcm for 2 hrs. ) . all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 12 25 mm dia 13 32 mm dia 14 40mm dia 15 50mm dia 16 80 mm dia 17 100 mm dia 18 supplying and fixing of pn 16 flanged y strainer fabricated out of cast iron body, ss 304 strainer with perforated screen with 3 mm. dia holesin existing ms / gi pipe complete with 2 no. matching flanges ( minimum 16 mm thick ) , nuts, bolts, washers, gaskets etc as required of following sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 19 100 mm dia 20 supplying and fixing of pn 16 cast iron dual plate wafer type check valve / non return valve with ss / bronze flap complete with 2 no. matching flanges ( minimum 16 mm thick ) , nuts, bolts, washers, gaskets, etc as required of following sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 21 100 mm dia 22 supplying and fixing of pn 1.6butterfly valve ( wafer type ) with s.g iron disc and confirming to is:13095 complete with 2 no. matching flanges ( minimum 16 mm thick ) , nuts, bolts, washers, gaskets, etc as required of following sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 23 100mmdia 24 supplying and fixing of pn 16 brass / gm ball valves with screwed end, ss ball including teflon tape etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 25 25 mm dia. 26 supplying and fixing of ss 304 single / double headed oblique pattern hydrant landing valve ( internal / external ) with 75 / 100 mm dia flanged inlet & 63 mm dia instantaneous type female outlet coupling with cast iron wheel complete with abs cap and chain and all accessories as per is:5290 93 ( type a ) in cluding matching flange ( 14 mm thick ) , nuts, bolts, washers, gaskets, etc as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 27 single headed with 75 mm dia. flanged inlet 28 supplying & fixing ss 304 short branch pipeconforming to is: 903:93 fitted with 20mm ( nominal internal diameter ) bore nozzle, for projecting water in form of solid jet. the branch shall have 63mm male instantaneous inlet, suitable for use with 63 mm size fire fighting hoses. h.p. tested to 21 kgf / cm² for 2.5 minutes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 29 supplying and fixing of flexible hose made with 100% polyester, black epdm internal rubber lining with external coat of synthetic elastomer ( is:636, type a ) 63 mm dia, 15 mtr. long rrl hose pipe with instanteneous type 63 mm dia ss 304male and female couplings ( is:903 ) duly bound and riveted to hose pipes with copper rivets and ss wire etc. as required.appropriate test certificate / report with liable warranty of product / accessories from oem shall be submitted. 30 supplying and fixing first aid fire hose reel drum wall mounted swinging type with ms construction powder painted in post office red, conforming to is 884 1985 with upto date amendments, complete with the following as required. ( a ) thermoplastic / rubber hose ( b ) 20 mmdia ul, fm bronze / ss nozzle with 5mm orifice ( c ) drum and brackets for fixing the equipments on wall. ( d ) connections from riser with 20 / 25 mm dia brass / gm gate valves with screwed end and conforming to is:778 class 1through forged steel screwed union & m.s. pipe. etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 31 with 30 m x 20 mm thermoplastic hose as per is:12585 type 2 and bursting pressure 42 kg / sqcm 32 providing & fixing stainless steel pressure gauge with dial of 150 mm dia size and range 0 to 20 kg / sq.cmwith 3 / 8 bsp bottom entry , ball valve , ss syphon tube all fittings etc, dulycalibrated before installation in mks and fps units, accuracy level + / 1% including making drilling in existing ms pipeetc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 33 sitc of ul 10th edition / en54 / vds certified microprocessor based inteligent, analogue addressable, modular, expandable networkableloop fire alarm control panel with each loop capacity of min 125 detectors per loop with total of 125 detectors & devices with loop length up to 1 km as per nfpa 72 approval. the panel shall be able to give pin point location of addressable units via the address code for each unit. the panel shall also be able to automatically switch off all control switches when ever any alarm is triggered. . the panel shall have 230 + 5 % volts power supply, automatic battery charger 24v, sealed lead acid maintanence free battries sufficient for 24 hours normal working and then be capable of operating the system for 30 minutes during emergency condtion. loop interface cards, communication module, lcd / led unit to indicate fire / fault signal of individual unit, inbuilt networking port ( both rs485ðernet ) , serial port for printer, two supervisory inputs, two position key switch and usb port for programming.including the cost of all accessories etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 34 1 loop panel 35 sitc of pressure switches ofpressure range 3 to 15 bar for main, jockey, terrace pumpanddiesel pumps, etc. as required ( control cable from pressure switch to panel to be paid extra ) . all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 36 supplying and fixing of 750 mm x 600 mm x 250 mm outdoor application fire hose cabinet made of 1.6 mm thick ms sheetduly powder coated in red color externally and white internally with 6 mm thick glazeddoors with expanded metal 2 mm thick jali including necessary locking arrangement suitable to accommodate 2 nos 15 mtr. long rrl hose and 1 no. branch pipe on existing wall / angle iron frame as required. ( cost of ms structure for mounting frame is to be paid extra ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 37 providing and fixing of 15 mm dia bronze quartzoid bulb type sprinkler headswith maximum working pressure 11.6 kg / sqcm and suitable for 68 degree centigrade rating standard response ( ul listed ) chrome plated complete in all respect of the following type. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 38 pendant / upright type 39 sitc of ul 10th edition / en54 / vds certifiedautomatic floating sensitivity type analog addressable multi criteria ( two optical / smoke sensor to reduce false alarm ) detector with mounting base & led etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 40 sitc of ul 10th edition / en54 / vds certified addessable manual call point ( mcp ) with led / fire indication etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 41 sitc of ul 10th edition / en54 / vds certified addressable sounder with strobe light, loop powered / direct powered from facp with sound level 90 db and programmablefrom the panel etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 42 supplying and fixing inlet breeching connection of ci body with gun metal male instantaneous inlet couplings with inbuilt nrv, drainage connection with 50 mm brass gate valvecomplete with pvc blank cap and chain as required for 150mm dia outlet with 1 no. matching flange ( minimum 16 mm thick ) , nuts, bolts, washers, gaskets, etc as required of following ways. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 43 2 way 44 supplying and drawing fire resistant flexible / stranded bare copper conductor, pvc / xlpe insulated, overall aluminium mylar tape shielded atc drain wire and outer pvc sheathed industrial instrumentation ( shielded ) cables voltage grade 300 / 500 v as per bs / en 50288 7 in existingsurface or recessed pvc / ms conduit / casing capping / cable tray / open duct making connections, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for cables. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 45 2 x 1.5 sq.mm armoured with outer sheath in red color 46 supply & fixing of co2 type fire extinguisher conforming to is:15683:2018, charged with co2 gas ( purity 99.7% conforming to is 15222 ) , powder coated internal & external surface manganese steel isi marked as per is 7285 cylinder body , wheel type forged brass release valve isi marked as per is 3224 with inbuilt safety release device ( ( fusible plug and rupture disc type ) , 1.0 mtr. metal wire braided hose having minimum bursting pressure of 140 kgf / cm2, horn with metallic thread connection, qr code for product traceability, including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 47 capacity 4.5 kg. 48 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 49 4 kg 50 supply & fabrication steel structure with ms channel / angle / joist / ismb / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as requiredcomplete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 51 s&f following sizes ( dia. ) of isi marked ( is:9537 p ii ) rigid steel conduit with wall thickness according to is specified along withisi marked ( is:14768 p ii 2003 ) accessories inrecessed using saddles, clamps, fasteners, pvc bushes, check nuts, as required includingcutting jhiris in the wall and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 52 25 mm 53 supply & fixing of ceiling mounted ul listed clean agent ( hfc 236fa ) , modular typefire extinguisher , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, fixed bulb with temerature 68 deg c, qr code for product traceability including fixing on ceiling with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 54 5 kg capacity...

Medical And Health Services - Rajasthan

36432578 tender for various work at blood bank in pbm campus bikaner clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 2 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils 3 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size ) . 4 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m15 grade nominal mix 1: 2: 4 ( 1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size ) . 5 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix 6 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcementfor walls ( any thickness ) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix / design mix 7 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix 8 centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. 9 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for :suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchorblocks, sills, chhajjas, lintel, beam, plinth beam etc. 10 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for :columns, pillars, posts and struts etc. 11 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor five level. ( original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to is:1786 ) thermo mechanically treated bars ( conforming of relevent is code ) 12 brick masonry with f.p.s. bricks of class designation 75 infoundation and plinth with bricks cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) 13 brick work with mechanised autoclaved flyash lime bricks conforming to is: 12894 :2002 of class designation 100 in superstructure above plinth level upto floor v level in.cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) 14 half brick work with mechanised autoclaved flyash lime bricks conforming to is: 12894 :2002 of class designation 75 in superstructure above plinth level upto floor v level in.cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) 15 grading roof for water proofing treatment withwater proffing compoundcement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) 16 making khurras 450 x 450mm with average minimum thickness 50mmcement concrete 1 : 2:4 over p.v.c. sheet 1 mtr. x 1 mtr. x 40micron finished with 12mm cement plaster 1 : 3 and onecoat of neat cement, rounding edges and making and finishing the out let complete. 17 providing&fixingprecastcementconcretecoping1:2:4mix50mmthickcompleteas per specification : 18 providing gola 75x75 mm in cement concrete 1:2:4 ( 1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge ) includingfinishing with cement mortar 1:3 ( 1 cement : 3 fine sand ) as per standard design : 19 providing and fixing unplasticized poly vinyl chloride ( upvc ) swr pipes type b for sciland waste discharge system ( is:13592 : 1992 marked ) of approved quality / make110 mm dia 20 providing and fixing unplasticized poly vinyl chloride ( upvc ) swr pipes fittings type b for sciland waste discharge system ( is:13592 : 1992 marked ) of approved quality / makecoupler 110mm dia 21 providing and fixing unplasticized poly vinyl chloride ( upvc ) swr pipes fittings type b for sciland waste discharge system ( is:13592 : 1992 marked ) of approved quality / makesingle tee 110mm dia 22 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 23 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. 24 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete 25 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completenew plastered surface ( three or more coats ) 26 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision new work 27 painting with synthetic enamel paint of approved brand and manufacture togive an even shade : two or more coats on new work 28 construction of granular sub base by providing well graded material, spreading in uniform layerson prepared surface, mixing by manual mean method at omc, and compacting with smoothwheelroller to achieve thedesired density, complete as per morth specification clause 401. with lead of material up to 20.00 km.from quarry for grading iii material 29 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size ) . 30 providing and laying of interlocking m 30 grade concrete block pavements having thickness 100 mm as per drawings and as per is 15658:2006.and all materials shall conform to morth specification clause 410. with m 30 grade 0.30 mtr x 0.30 mtr x 0.15 mtr edge blocks.category b : dentated only two side like i, z, t shape as per irc:sp:63 2004 31 kerb stones of 1200x300x150, 1000x450x150, 1000x600x150, 600x300x150 size ( m 30 ) providing and laying cement concrete kerb stones of different sizes in m 30 grade ( manufactured with fully mechanised dry cast process with forced action mixer whose arms revolve along the main axis and rotate about its own axis also, having humidity sensor for moisture control of w / c ratio in concrete mix. manufactured with steel moulds ( milled and manufactured in csi diamond or csi nitro process for accuracy ) on steel base plate of min 16 mm thick;having vibration and pressing action both together withthe help of multiple synchronised vibrators.power of hydraulic station should be minimum 50kw for compaction and cured in controlled chambers having humidity control and automated air circulation system ) in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand ) including making of joints, drainage opening wherever required. 32 rewiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessedisi marked mms ( is:9537 p iii ) virgin material pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thick ms box with earth terminal, 6 a switch, 3 pin ceiling rose / holder / 3 way connector , 3.0 mm thick isi marked ( is:2036 1995 ) phenolic laminated sheet, al.alloy / cadmium plated iron / brassscrews, cup washers, making connections, testing etc. as required. for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr short point ( up to 3 mtr. ) 33 medium point ( up to 6 mtr. ) 34 long point ( up to 10 mtr. ) 35 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr on board 36 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 20 mm 37 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 2 x 2.5 sq. mm. + 1x1.5sqmm 38 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 39 p & f phenolic laminated sheet 2.0 mm thick of following size . including screws, cup washer as required.for additional technical parameters of product / work refer annexure a attached with this bsr 75 mm dia 40 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr single pole mcb ( with b / c curve tripping characteristics ) 6 a to 32 a rating 41 double pole mcb ( with b / c curve tripping characteristics ) 6 a to 32 a rating 42 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr metal door ( three phase ) ik 09 and ip 43with metal end box 6 way 43 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts© connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr .17.2 mm thick and 3 mtr. long 44 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 1200 mm sweep bee 3 star rated ( service value >=5.0 to< 5.5 ) 45 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminiumhousing with in built driver, system lumen efficacy = 110 lm / watt output, internal surge protection of 2.5 kv with short & open circuit protection , thd < 10% , p. f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 1170mm ( + / 10% ) led batten with min. lumen output 2200 lm 46 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 6.0 sq. mm 4 core 47 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . led street light fixture with minimum lumen output 8700 lm...

Public Works Department - Rajasthan

36390195 tender for various development work in narhar dargah jhunjhunu demolishing brick work manually / by mechanical meansincluding stacking of serviceable material and disposal ofunserviceable material within 50 metres lead as per directionof engineer in charge. 3 demolishing stone rubble masonry manually / by mechanicalmeans including stacking of serviceable material and disposalof unserviceable material within 50 metres lead as perdirection of engineer in charge: 4 dismantling precast concrete or stone slabs in wallpartitions etc. including stacking within 50 meter lead: 5 earth work in surface excavation not exceeding 30cm. indepth but exceeding 1.5 meter in width as well as10 sqm onplan including disposal of excavated earth up to 50 mtr. andlift up to 1.5 mtr. disposed soil to be levelled and neatlydressed : all kinds of soil 6 earth work in excavation by mechanical means ( hydraulicexcavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) includingdressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing andrefilling of jhiri with watering & ramming and disposal ofsurplus excavated soil as directed with in a lead of 50 meter.all kinds of soils 7 excavation work by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains not exceeding1.5 m in width or 10 sqm on plan including dressing of sidesand ramming of bottoms lift upto 1.5 m, including getting outthe excavated soil and disposal of surplus excavated soil asdirected with a lead in a 50 meter including stacking of usefulmaterial if available : 8 diluting and injection chloropyrifos emulsifiable concentrate 20% with 1% concentration for pre constructional anti termite treatment as per is 6313 part iii as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which aproch is to be laid surrounding of pipes and conduits etc. complete as per specification ( plinth floor area only shall be measured for payment and excluding the cost of chemical emulsion ) 9 providing and laying in position cement concrete includingcuring, compaction etc. complete in specified grade excludingthe cost of centering and shuttering all work up to plinthlevel. 1:4:8 ( 1cement :4 course sand :8 graded stone aggregate 40 mm nominal size= 10 centering and shuttering with plywood or steel sheetsincluding strutting, propping bracing both ways and removalof formwork for foundation , footings, strap beam, raft , basesof columns etc. 11 providing and laying in position specified grade of cementconcrete for all rcc structural elements upto plinth levelincluding curing, compaction, finishing with rendering incement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and makinggood the joints and cost of plastizers ( if required ) excludingthe cost of centering, shuttering and reinforcement. 12 excavating holes upto 0.5 cum including getting out theexcavated soil, then returning the soil as required in layers notexceeding 20 cm in depth, including consolidating eachdeposited layer by ramming, watering etc, disposing of surplusexcavted soil; as directed within a lead of 50 m and lift to 1.5 m 13 random rubble stone masonry for with hard stone infoundation and plinth in cement sand mortar above 30 cmthick wall in: cement mortar 1:6 ( 1 cement:6 sand ) . 14 random rubble dry stone kharanja under floor. 15 centering & shuttering with plywood or steel sheets includingstrutting, propping bracing both ways with steel props andremoval of formwork for upto floor five level for : columns, pillars, posts and struts etc. 16 centering and shuttering with plywood or steel sheets including strutting, propping, bracing both ways with wooden members andremoval of formwork for superstructure up to 4.5 mtr aboveplinth, for:suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands , coping, bed plates, anchor blocks, sills, chhajjas lintel, beam etc. 17 providing and laying in position specified grade of cementconcrete for rcc structural elements upto floor five levelincluding curing, compaction, finishing with rendering incement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and makinggood the joints and cost of plastizers ( if required ) excludingthe cost of centering, shuttering and reinforcement for walls ( any thickness ) including attached pilasters, buttresses, plinthand string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix / design mix 18 providing and laying in position specified grade of cementconcrete for rcc structural elements upto floor five levelincluding curing, compaction, finishing with rendering incement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and makinggood the joints and cost of plastizers ( if required ) excludingthe cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plainwindows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix 19 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor three level.tremo mechanically treated bars 20 brick work with f.p.s. bricks of class designation 75 insuperstructure above plinth level upto floor v level in allshapes and sizes in :.cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) 21 half brick masonry in superstructure , above plinth level uptofloor v level using bricks of designation 75cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) 22 providing and fixing marble stone flooring table rubbed, 15 18 mm thick over 20mm ( av. ) thick base of cm 1:4 ( 1 cement: 4 coarse sand ) jointing with white cement mortar 1:2 ( 1 whitecement : 2 marble dust ) with pigment to match the shade of themarble slab including grinding, rubbing and polishingcomplete..upto to 1500 cm2 tiles 23 providing and fixing marble stone flooring table rubbed, 15 18 mm thick over 20mm ( av. ) thick base of cm 1:4 ( 1 cement: 4 coarse sand ) jointing with white cement mortar 1:2 ( 1 whitecement : 2 marble dust ) with pigment to match the shade of themarble slab including grinding, rubbing and polishingcomplete. size upto 1500 cm2 ) 24 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shadesglazed tiles confirming to is : 13753 & is :15622 of size200mm x 300mm in walls, floors, steps, pillars etc. laid on abed of neat cement slurry finished with flush pointing in thewhite cement mixed with pigment to match the shade of thetile complete ( excluding the cost of cement plaster on wallsand pillar ) .somani make etc. 25 providing and fixing granite stone slab mirror polished andmachine edge cut in walls, pillars, steps, shelves, sillscounters, floors etc. laid on 12mm ( av. ) thick base of cementmortar 1:3 ( 1 cement : 3 coarse sand ) jointing with whitecement mortar 1:2 ( 1white cement : 2 marble dust ) withpigment to match the shade of the marble slab includinggrinding, rubbing and polishing complete 26 jhunjhunu / jalore ( red / choclate / black / pink colour ) 27 size above 3600 cm2 28 kota stone slab flooring 25 mm thick over 20 mm ( average ) thick base laid over and jointed with grey cement slurrymixed with pigment to match the shade of the slab includingrubbing and polishing complete with base of cement mortar 1: 4 ( 1 cement : 4 coarse sand ) 29 for area of each slab from 901 to 2000 sq.cm : 30 ( a ) 25 mm thick slab. 31 kota stone slab flooring 25 mm thick over 20 mm ( average ) thick base laid over and jointed with grey cement slurrymixed with pigment to match the shade of the slab includingrubbing and polishing complete with base of cement mortar 1: 4 ( 1 cement : 4 coarse sand ) 32 for area of each slab from 2001 to 5000 sq.cm 33 ( a ) 25 mm thick slab. 34 kota stone slabs 25 mm thick in risers of steps, skirting, dadoand pillars laid on 12 mm ( average ) thick cement mortar 1:3 ( 1cement 3 coarse sand ) and jointed with grey cement slurrymixed with pigment to match the shade of the slabs, includingrubbing and polishing complete 35 for area of each slab from 2001 to 5000 sqcm 36 providing and fixing 1st quality mat finished ceremic tilesize 300x300mm confirming to is : 13755 and is : 15622colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc.laid on a bed of neat cement slurry finished with flush pointingin the white cement mixed with pigment to match the shade ofthe tile complete ( including the cost of cement mortar bed 37 providing and fixing 1st quality mat finished ceremic tilesize 300x300mm confirming to is : 13755 and is : 15622colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc.laid on a bed of neat cement slurry finished with flush pointingin the white cement mixed with pigment to match the shade ofthe tile complete ( including the cost of cement mortar bed 38 providing and fixing pressed steel door frames confirming tois 4351 manufactured from commercial mild steel sheet of1.25 mm thickness including hinges jamb, lock jamb, bead andif required angle threshold of mild steel angle of section50x25mm, or base ties of 1.25mm pressed mild steel weldedor rigidly fixed together by mechanical means, adjustable lugswith split end tail to each jamb including steel butt hinges2.5mm thick with mortar guards, lock strike plate and shockabsorbers as specified and applying a coat of approved steelprimer after pre treatment of the surface including filling withcc 1:2:4 ( m15 grade ) complete as directed by engineer incharge 39 profile b 40 providing and fixing in position collapsible steel shutters withvertical m.s. channels 20 x 10 x 2mm and bracket with flatiron diagonals 20 x 5mm. size with top and bottom rail of tiron40 x 40 x 6mm. with 40mm dia steel pulleys / ball bearingcomplete with bolts, nuts locking arrangements inside andoutside stoppers, handles etc. as per specification includingapplying a priming coat of approved steel primer. ( to bemeasured and paid as per outer dimension ) 41 providing and fixing m.s. sheet 1mm thick single leaf doorshutter in angle iron frame 35x35x5mm suitabilly diagonallybraced with 25x3mm flat iron above and below lock rail ofsize 50x5mm beading extra including all fittings, as perdirection of engg. incharge but excluding cost of chowkhats:including two coats of anit corrosive red oxide primer paint 42 providing and fixing steel glazed doors windows andventilator shutters of standard rolled steel section ( is 1038 1983 ) joints mitred and welded with steel lugs 13x3mm, 10cm.long embedded in cement concrete block 15x10x10cm. of1:3:6 ( 1cement : 3 coarse sand : 6 graded stone aggregate20mm nominal size ) or with wooden plugs and screws or rawlplugs and screws with fixing clips or with bolts and nuts asrequired including providing and fixing of plain glass panes4mm thick with cooper glazing clips and special metal sashputty of approved make or metal beading with screwscomplete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting exceptnecessary hinges of pivots steel handles peg stay etc. asrequired : 43 supplying and fixing fixed wire gauge of 14 mesh x 24 gaugeto the metal frame of rolled section by metal beading 20x3mmwith suitable screw at not exceeding 150mm distance. 44 providing and fixing external grade board solid core singleleaf flush door shutters isi 2202 67 marked using phenolformal dehyderesin in glue both sides with approved steelfittings complete as per annexure a : 45 decorative teak veener both side 46 30 mm thick shutter 47 add extra for flush doors 48 extra for cutting rebate in flush door shutters for makingdouble leaf shutter ( total area of the shutter to be measured ) . 49 p & f bevelled edge mirror / mirror with teak wood lippingaround of special glass of approved make as per direction ofengineer in charge complete with 6mm thick commercial plybase fixed to wooden screws & washers.size 600 x 450mm x 4 mm thick 50 providing and fixing 18 mm thick, 150 mm wide pelmet of flatpressed 3 layer or graded wood particle board medium densitygrade i, is : 3087 marked including top cover of 6 mmcommercial ply wood conforming to is: 303 bwr grade, nickel plate ms 20 mm dia curtain rod with nickel platedbracket including fixing with 25x3 mm ms flat 10 cm long allcomplete 51 providing and fixing curtain rods of 1.25 mm thick chromiumplated brass plate, with two chromium plated brass bracketsfixed with c.p. brass screws and wooden plugs, etc., wherevernecessary complete: 52 20 mm dia. 53 plaster on new surface on walls in cement sand mortar 1:6including racking of joint etc. complete fine finish : 54 20 mm thick. 55 grading roof for water proofing treatment with waterproffing compound cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 gradedstone aggregate 20 mm nominal size ) 56 providing gola 75x75 mm in cement concrete 1:2:4 ( 1 cement: 2 coarse sand : 4 stone aggregate 10mm and down gauge ) including finishing with cement mortar 1:3 ( 1 cement : 3 finesand ) as per standard design : 57 providing and applying plaster of paris putty of 2 mmthickness over plastered surface to prepare the surface evenand smooth complete 58 painting with oil type wood preservative of approved brandand manufacture : new work ( two or more coats ) . 59 distempering with oil bound washable distemper of approvedbrand and manufacture to give an even shade including allscaffolding: new work ( two or more coats ) over and includingscrapping and priming coat with cement primer. 60 applying priming coat with ready mix pink or gray primer of approved brand andmanufacture on wood work hard and soft wood. 61 finishing wall with water proofing cement paint of approvedbrand and manufacture and or required shade to give an evenshade including all scaffolding: new work ( two or more coats applied @ 3.84 kg / 10 sqm ) . 62 providing & fixing precast cement concrete coping 1 : 2: 4 mix 50mm thick complete as per specification : 63 extra for providing edge moulding to 15 18mm thick marble / granite / kota stone counters, vanities etc. including machinepolishing to edge to give high gloss finish etc. complete as perdesign approved by engineer in charge.marble work ( i ) full edge moulding 64 marble work 65 providing and fixing aluminum work for doors , windows, ventilators and partition with extruded built up standardtubular / appropriate z sections and other sections of approvedmake conforming to is :733 and is :1285, fixed with rawlplugs and screws or with fixing clips , or with expansion holdfasteners including necessary filling up of gap. at junctions , attop , bottom and sides with required pvc / neoprene felt etc.aluminium section shall be smooth , rust free, straight , miteredand jointed mechanically wherever required including cleatangle aluminium snap beading for glazing / paneling , c.p.brass / stainless steel screws al. tower bolt & al. handle & al.aldrop etc., all complete as per architectural drawings and thedirections of engineer in – charge . ( glazing and paneling tobe paid for separately ) . for fixed portion anodised aluminum ( anodised transparent 81 dyed to requiredshade according to is : 1868. ( minimum anodic coating ofgrade ac 15, anodizing to be got done from approvedanodizer ) 66 for fixed portion 67 providing & fixing anodizing alumium work ( anodizing to be got done from approved anodizer ) for doors, windows, ventilators and partition with extruded built up standard tubular and other sections of approved make confirming to is : 733 and is : 1285 anodised transparent 81 dyed to required shade according to is : 1868 ( minimum anodic coating of grade ac 15 ) , fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gas at junctions, at top, bottom and sides with required pvc / neoprene felt etc. aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required inlcuding cleat angle aluminum snap beading for glazing / paneling, c.p. brass / stainless steel screws, al. tower bolt & al. handle & al. aldrop etc. all complete as per architectural drawings and the directions of engineer in charge. ( glazing and peneling to be paid for separately ) . 68 anodised aluminum ( anodised transparent 81 dyed to requiredshade according to is : 1868. ( minimum anodic coating ofgrade ac 15, anodizing to be got done from approvedanodizer ) . 69 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with pvs / neoprenegasket etc. complete as per the architectural drawings and thedirections of engineer in charge. ( cost of aluminium snapbeading shall be paid in basic item. ) with float glass panes of 5.0 mm thickness ( weight not lessthan 13.50 kg / sqm ) 2835 70 providing and fixing glazing in aluminium door, window, vintilator shutters and partitions etc. with pvs / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge ( cost. of aluminium snap beading shall be paid in basic item. ) with with float glass panes of 8 mm thickness 71 extra for providing frosted glass panes instead of ordinary float glass panes in doors, windows and clerestory window shutters. ( area of opening for glass panes excluding portion inside rebate shall be measured ) . 72 providing and fixing double action hydraulic floor spring ofapproved brand and manufacture is : 6315 marked, for doorsincluding cost of cutting floors as required, embedding infloors and cover plates with brass pivot and single piece m.s.with brass cover plate 73 providing and fixing expanded grill made of aluminum as per designand drawing having members section of size 7.5mm x 6.0mm andopening of size 102mm x 99mm to aluminum window / vent withrequired screws, y and h aluminium section ( as per drawing ) at theends and middle joints respectively complete in all respect as perdirection of engineer in charge. anodised aluminum ( anodised transparent 81 dyed to required shadeaccording to is : 1868. ( minimum anodic coating of grade ac 15, anodizing to be got done from approved anodizer ) 74 providing and fixing 100mm brass locks ( best make of approvedquality ) for aluminium doors including necessary cutting and makinggood etc. complete. 75 stainless steel ( ss 304 grade ) adjustable friction window stay. 510 x 19mm 76 providing & fixing of ward robe shutters made out of 19mmthick bwp block board isi of superior quality make withfollowing details : front side finishing with 1mm thick superior quality micaapproved make and 0.8mm thick approved shade mica in theinner side. covering with teak wood beading 25x12mm all thesides of shutter & 35x12mm on outer frame for making goodthe wall joint including heavy brass s.s. fittings ( handle200mm 2 nos., tower bolt 150mm 2 nos., brass lock 1 nos., magnetic catcher 2 nos., brass hinges 75x40x2.5 mm 6 nos., ss hanger rod 20mm dia ) complete as per drawing anddesign approved by engineer in charge. 77 providing and fixing stainless steel railing made of hollowtubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts andbolts complete, i / c fixing the railing with necessaryaccessories & stainless steel dash fasteners , stainless steelbolts etc., of required size, on the top of the floor or the side ofwaist slab with suitable arrangement as per approval ofengineer in charge, ( for payment purpose only weight ofstainless steel members shall be considered excluding fixingaccessories such as nuts, bolts, fasteners etc. ) .grade 204 78 p & f indian type white glazed vitreous china ist quality w.c. orissa pan ( is:2556 mark ) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor :size 530x410mm. 79 p & f water closet seat covers with brass hinges complete :solid pvc ( isi marked ) grade i white for ewc. 80 p & f w.v.c. urinal partition plate of approved standardmake of size 630x315mm including making good the wall. 81 p & f marble urinal partition slab both sides polished of approved design cut from marble size 900x600mm. 82 makrana ii quality marble having light spots. 83 p & f w.v.c. half round channel of approved make in c.m.1:3 joints finished in white cement of 84 size 150 mm dia. 85 p & f low level flushing cistern of 10 litres capacity ( is:2556 mark ) of approved make with complete fittings c.i. brackets duly painted, brass ball cock with ball, ( is:1703 mark ) complete including cutting and making good the wall : wvc with c.p. brass bend. 86 p & f c.p. brass urinal flush pipe set complete with flanged brackets of approved make. 87 for 1 urinals. 88 p & f c.p. brass urinal spreader for stall urinal of approved make. 89 p & f wvc wash basin ( ist quality is:2556 mark ) of approved make with c.i. brackets duly painted 1 no. 15 mm c.p. pillar cock ( is:8934 mark ) & 32 mm c.p. brass waste coupling of approved make 25 mm g.i. waste pipe complete including cutting & making good the wall :size 630 mm x 500 mm dia for counter top. 90 providingandfixingsuperiorqualitycpbrassfittingsofapprovedmakeasperdirectionofengineer in chargeswan neck pillar cock 15 mm nominal size 91 providingandfixingsuperiorqualitycpbrassfittingsofapprovedmakeasperdirectionofengineer in chargesingle lever wash basin mixer with 450 mm long copper connection pipe 92 p&f beveled edge mirror of special glass of appd make ( atul / equivalent ) complet with6mm thick asbestos cemetn sheet ground fixed to wooden scrwes & washers.other sizes 93 c.p. brass towel rail elbow type with concealed screws size 450mm ( heavy duty ) 94 providingandfixingsuperiorqualitycpbrassfittingsofapprovedmakeasperdirectionofengineer in chargesoap dish 95 p&f extension pipe for bib cocks of approved quality / make: 96 do 100x15mm 97 making connection of g.i. distribution branch with g.i. main including all fitting. 98 beyond 25 mm & up to 100 mm dia. 99 providingandfixingsuperiorqualitycpbrassfittingsofapprovedmakeasperdirectionofengineer in charge 100 p & f pillar cocks ( is:8934 mark ) of superior quality and approved make : 101 p & f inlet connection ( angle valves ) superior quality, of approved make, for wash basin, gyser etc. do with 37 cm. long pipe and nut. 102 p & f 15 mm. dia connection pipe of approved quality / make:c.p. brass pipe with cp brass nuts upto length 600 mm. 103 p & f flush cock / flush valve ( is:9758 mark ) or wc of approved quality make : 104 c.p. brass push type exposed 25 mm nominal bore. 105 p & f full way valve ( is:778 mark ) or wheel valve of approved make : 106 gun metal 20 mm nominal bore. 107 p & f full way valve ( is:778 mark ) or wheel valve of approved make : 108 gun metal 25 mm nominal bore. 109 p & f pvc storage tank ( is:12701 marked indicating the bis license no. ) of approved make with cover, 25 mm dia 1 m long g.i. over flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc. complete of approved design. 110 1000 litres capacity. 111 p & f g.i. pipes ( internal work ) with g.i. fittings ( is:1239 mark ) & m.s. clamps including cutting and making good the walls and floors : 112 20 mm dia nominal bore. 113 p & f g.i. pipes ( internal work ) with g.i. fittings ( is:1239 mark ) & m.s. clamps including cutting and making good the walls and floors : concealed pipe in wall incl. with anticorrosive bitumen paint. 114 20 mm dia nominal bore. 115 p & f g.i. pipes ( external work ) with g.i. fittings ( is:1239 mark ) including trenching & refilling earth etc.20 mm dia nominal bore. 116 p & f g.i. pipes ( external work ) with g.i. fittings ( is:1239 mark ) including trenching & refilling earth etc. 117 25 mm dia nominal bore. 118 p&f rigid pvc pipe ( is:4985 mark ) class ii ( 4 kg. / cm. ) approved quality / makeincluding joining the pipe with solvent cement rubber ring and lubricant 119 110mm dia 120 75mm dia 121 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant: 122 coupler 123 110mm dia 124 75mm dia 125 plain tee 126 110mm dia 127 75mm dia 128 bend 87.5 129 110mm dia 130 75mm dia 131 pipe clip 132 110mm dia 133 75mm dia 134 gully trap 135 110mm dia 136 door bend ( top side ) 137 110mm dia 138 construction of manhole in all type of soil inner size 90 x 60 cm. thick masonry in cm 1:6, 10 cm. thick cement concrete 1:5 10 in foundation, 20 mm thick inside plaster in cm 1:6, finished with floating neat cement, 50mm thick m 15 grade c.c. flooring, making channels, 80mm thick stone slab covering with 40mm thick m 15 grade c.c.flooring , 25 kg. ci cover with frame of 40mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. 139 depth upto 0.5mtr 140 construction of chamber in all type of soil with 300 mm thickmasonry in cm 1:6 m, 10 cm thick c.c. 1:5:10 in foundation, 20mm thick insider plaster in cm 1:6, finished with floatingneat cement, 50mm thick m 15 grade c.c. flooring , earthwork etc. complete as per design including disposal ofsurplus earth within a lead of 50 mtr 141 inside size 300x300mm depth upto 0.5m & 5kg c.i. cover with frame 142 size 450 x 450mm upto depth of 0.5m & 15kg ci cover with frame 143 do size 600x450mm upto depth of 0.5m & 38kg ci cover with frame 144 construction of septic tank in all type sof soil with 40cm thick masonry in cm 1:6 15cm thick cc bed of 1:5:10 m 15 grade cc flooring & over stone slab covering, 80mm thick slab jointing of slab in cm 1:3, ralthal, kharanja, 50mm thick stone partiton walls, 20mm thick plaster in cm 1:6 finished with neat floating cement, 4nos c.i. foot rests of approved design, two no. 450mm dia 25kg each c.i. cover with frame, earth work etc. complete as per approed drawing incl. disposal of surplus earth wtihin a lead of 50mtr. 145 size 230x110x150cm ( for 20users ) 146 size 400x140x150cm ( for 50users ) 147 construction of open surface drain with 112 mm thick brick masonary in cm 1:4, 110mm thick base concrete 1:5:10, 37mm thick m 15 grade c.c. flooring, 12 mm 1:4 cement plaster on all exposed face of walls including top surface excavation & disposal of earth complete as per approved design / drawing: 148 250mm drain 300mm av. depth 149 providing and fixing unplasticized poly vinyl chloride ( upvc ) swr pipes type `b for sciland waste dischareg system ( is : 13592: 1992 marked ) of approved quality / make. 150 construction of soakage well in all type of soil 300 mm thick dry masonry top and bottom 300 mm course in cm 1:6, 80 mm thick stone slab, jointing of slab in cm 1:3, ralthal, kharanja, 40 mm thick m 15 grade c.c. flooring, earth work complete as per approved drawing including disposal of earth within a lead of 50 mtr. : 151 size 300 cm. dia outside & 300 cm. depth. 152 size 240 cm. dia outside & 240 cm. depth. 153 p&f grating of approved quality / make 154 stainless steel sheet size 125mm dia 155 p&f liquid soap contained with brackets complete of approved make : 156 c.p. brass 157 p&f rigid pvc pipe ( is:4985 mark ) class ii ( 4 kg. / cm. ) approved quality / makeincluding joining the pipe with solvent cement rubber ring and lubricant 158 160mm dia 159 providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering =all up to plinth leve1:3:6 ( 1cement :3 course sand :6 graded stone aggregate 20 mm nominal size 160 earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed within a lead of 50 meter.all kinds of soil. 161 earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed within a lead of 50 meter.all kinds of soil.add extra for foundation / trenches / drains for every additionallift of 1.5 mtr. or part thereof in 162 providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering =all up to plinth leve1:4:8 ( 1cement :4 course sand :8 graded stone aggregate 40 mm nominal size 163 providing and laying in position specified grade of cementconcrete for all rcc structural elements upto plinth levelincluding curing, compaction, finishing with rendering incement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and makinggood the joints and cost of plastizers ( if required ) excludingthe cost of centering, shuttering and reinforcement.m20 grade nominal mix / design mix 164 centering & shuttering with plywood or steel sheets includingstrutting, propping bracing both ways with steel props andremoval of formwork for upto floor five level for : walls ( any thickness ) including attached pilasters, buttresses plinth and string course. 165 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor three level.tremo mechanically treated bars 166 providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls ( any thickness ) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string orlacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor fivelevel excluding the cost of centering and shuttering.m15 grade nominal mix1: 2: 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate20mm nominal size ) . 167 plaster on new surface on walls in cement sand mortar 1:4 including raking of joints etc. complete fine finish: 12 mm thick. 168 plaster on new surface on walls in cement sand mortar 1:4 including raking of joints etc. complete fine finish: 20 mm thick. 169 p&f rigid pvc pipe ( is:4985 mark ) class ii ( 4 kg. / cm. ) approved quality / makeincluding joining the pipe with solvent cement rubber ring and lubricant 110mm dia 170 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant: bend 87.5 171 painting with enamel paint of approved brand and manufacture to give an even shade: two or more coats on new work. 172 steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m ) fixing in position and applying apriming coat of approved steel primer, welded and boltedincluding special shaped washers etc. complete hot finished welded type tubes....

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

36348920 tender for bwd wall and major repair work in govt.ps hisamda ( weir ) dismantling brick tiles covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. 3 dismantling stone slab / terrazo chip flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead. 4 dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. 5 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils 6 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size ) . 7 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1 cement : 6 sand ) . 8 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix 9 centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. 10 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in :cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) 11 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in :cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) add extra for square or rectangular pillars in superstructre brick work up to five storey upto 45 cm length and all sides are free 12 half brick masonary in s.s. with bricks of class desiganation 75 in c.m 1:6 13 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix 14 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for :suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchorblocks, sills, chhajjas, lintel, beam, plinth beam etc. 15 providing and fabricatin steel reinforcement for rcc work including cutting bending placing in position and binding complete including cost of binding wire in foundation faft footng step beams base of columms etc. upto plinth level hot rollet deformed ( 1st 1139 ) cold twisted bars. at ground floor. 16 random rubble dry stone kharanja under floor 150 mm thick. 17 providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:3:6 ( 1 cement:3 coarse sand :6 gradeed stone aggregate 20 mm nominal size ) . 18 plaster ( internal ) plaster on new surface on wall in cement sand mortar 1:4 including ranking of joints etc. complete fine finished 12 mm thick 19 plaster ( external ) plaster on new surface on wall in cement sand mortar 1:6 including ranking of joints etc. complete fine finished20 mm thick 20 kota stone slab flooring 25 mm thick over 20mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement: 4 course sand ) for area 2001 to 5000 sq. cm 21 coping: providing and laying cement concrete including curing compaction etc. complete in retaining walls, return walls, walls ( any thickness ) including attached pilasters, columns, piers, abutments, pillers, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc upto floor five levelexcluding the cost of centeringand shuttering.m15 grade nominal mix 1:2:4 ( 1 cement:2 coarse sand :4 gradeed stone aggregate20 mm nominal size ) . 22 providing and fixing t iron frames for doors, windows and ventilators of mild steel tee sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1 :3:6 ( 1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size ) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 23 providing and fixing ms sheet dobule leaf door shtter in angle iron frame 35x35x5 mm suitability diagonally braced with 25x3 mm flat iron above and below lock rail of size 50x5 mm beading extra including. all fittings as per direction of enginneer in charge but excluding cost of chokhats m.s sheet 22 s.w.g. 24 providing and fixing steel glazed doors windows and ventilator shutters of standarad rolled steel section joints mitred and welded with lugs 13x3mm, 10cm long embeded in cement concrete block 15x10x10cm of 1:3:6 or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with coper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approved steel primer, excluding the cost of metal beading and other fittings expect necessary hings of pivots steel handles peg stay etc.as required for windows fixedpartly fixed and partly openable [ fixed area not to exceed 33% ] 25 supplying & fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 26 providing and fixing square bars or other flat welded to window ventilators etc. 27 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completenew plastered surface ( three or more coats ) 28 panting on doors & windowspainting with enemel paint of approved brand and manufacture in all shade on new steel work ( 2 or more coat ) 29 finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. new work ( two or more coat applied @ 1.67 ltr / 10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg / 10 sqm ) . 30 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:newwork ( twoormorecoats ) overandincludingscrappingandprimingcoatwithcement primer. 31 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete ( excluding the cost of cement plaster on walls and pillar ) . 32 chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles includingrubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand ) light shade using shade cement. 33 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 34 sanitry work 35 providing and fixing indian type white glazed vitreous china 1st quality w.c. orissa pan ( i.s. 2556 mark ) with 100mm vitreous china p or s trap including utting and making good the wall and floor size 580x440mm. 36 p & f g.i. pipes ( internal work ) with g.i. fittings excluding union ( is:1239 mark ) & ms clamps including cutting and making good the walls and floors: 37 p&f g.i. pipes ( external work ) with g.i. fitting ( is:1239 mark ) & ms clamps, including cutting and making good the walls and floors. 25mm dia. nominal bore.b class 38 p&f bib cock ( is:8931 mark ) , primer quality of approved makebib cock 15mm nominal bore. 39 p&f 15 mm dia connection pipe of approved quality / make pvc pipes with nuts 450mm. 40 p&f flush cock / flush valve ( is :9758 ) for wc of approved make cp brass 25 mm nominal bore. 41 p&f full way valve ( is:778 mark ) or wheel valve of approved make. gun metal 25 mm nominal bore. 42 p & f pvc storage tank ( is 12701 marked indicating the bis licence no. ) of approved make with cover, 25mm dia 1m long g.i. over flow pipe and 25 cm long wash out pipe with plug & socket including making connection etc complete of approved design. 500 43 p& f rigid pvc pipe ( is 4985 mark ) class 2nd / ( 4 kg / sqcm ) approved quality / make including joining the pipe with solvant cement rubber ring and lubricant 110 mm dia. 44 pvc bend 110mm 45 pvc clip 110mm 46 electricwork 47 wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 48 short point ( up to 3 mtr. ) 49 medium point ( up to 6 mtr ) 50 wiring of 3 pin 5 amp. light plug point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade and 1.5 sq. mm nominal size fr pvcinsulated unsheathed flexible copper earth conductor 1.1 kv grade ( is: 694 ) of approved make in surface / reces group 2 51 on board 52 s&f following sizes ( dia. ) of isi marked ( is:9537 p ii ) rigid steel conduit with wall thickness according to is specified along withisi marked ( is:14768 p ii 2003 ) accessories inrecessed using saddles, clamps, fasteners, pvc bushes, check nuts, as required includingcutting jhiris in the wall and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 53 25 mm dia 54 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 55 2 x 1.5 sq. mm 56 2 x 2.5 sq. mm +1 x1.50sq.mm 57 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 58 6 a to 32 a rating 59 providing & fixing of ip 20 boxmade outfrom 1.2mm thick crca sheet steel with depth of minimun 30 mm and finished with powder coating andsuitable for mounting led tubeincludingside covers, holders , internal wiring to illuminate the single sided connection led tube. ( without tube ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 60 suitable for 4 led tube shape fixture for double rod 61 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 62 6.0 sq. mm 4.00core 63 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 64 1200 mm sweep bee 1 star rated ( service value >=4.0 to < 4.5 ) 65 providing & fixing of is 11037:1984markednon modular socket size flush type 180 watt rotary minimum 5 step fan regulator with cm / l no. printed and made out from industrial grade polycarbonate or fire resistant abs material including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 66 providing & fixing ofisi marked ( is:371 ) 6 amp surface type 3 pin ceiling rose with cm / l no. printed and made out from industrial grade polycarbonate or fire resistant abs material, brass terminal & captive screws including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 67 providing & fixing of isi marked ( is:1258 ) batten / angle lampholder with cm / l no. printed and made out from industrial grade polycarbonate or fire resistant abs material, brass terminal & captive screwsincluding making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 68 p & f 1.2 mm thickg. i. / m .s. sheet boxes duly finished with two coats of red oxide and with earthing terminal of following sizes ( nominal size ) in recessed / surface as required.for additional technical parameters of product / work refer annexure a attached with this bsr 69 p & f 1.2 mm thickg. i. / m .s. sheet boxes duly finished with two coats of red oxide and with earthing terminal of following sizes ( nominal size ) in recessed / surface as required.for additional technical parameters of product / work refer annexure a attached with this bsr 70 150mm x 150mm x 60mm...

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

36095095 tender for civil work in govt pravisika sanskrit nokha naov part a (building work) based on bsr pwd 2019, bikaner 2 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.all kinds of soils 3 pcc in foundation :providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8(1 cement:4 coarse sand :8 graded stone aggregate 40 mm nominal size). 4 brick work masonary with f.p.s bricks of ist class desgnation in foundation and plinth in. cement sand mortar 1:6 ( 1 cement :6 coarse sand) add extra over item of brick workwith class designation 10.0 in substitutionof class designation 7.5 :quantity in cum. 5 plinth beam: providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix 6 dry brick on edge flooring in required pattern with bricks of class designation 75 on bed of 12 mm mud mortar including filling joints with river sand complite . 7 half brick work : half brik masonary in supperstructure , above plinth level up to floor five level using f.p.s.bricks of designation 75 cement mortar 1:4 (1 cement:4 course sand) 8 flyash brick work: brick work with mechanised autooclaved flyash lime bricks conforming to is: 12894 :2002 of class designation 100 in superstructure above plinth level up to floor five level in cement mortar 1:6. 9 lintel beams: providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( as required) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. m20 grade nominal mix / design mix 10 slab & beam: providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( as required) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. m20 grade nominal mix / design mix 11 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for :suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 12 steel reinforcement: p/f reinforcement for rcc work including straightening,cutting, bending, placing in position and binding (including cost of binding wire)all complete upto floor five leve tmt bars (conforming of relevent is code). 13 door frames: structural steel work in single section fixed with or without connecting plate including cutting, hoisting ( height upto 10 m), fixing in position and applying a priming coat of approved steel primer all complete.angle iron (40x40x5mm. @ 3 kg/m) 14 doors: providing and fixing m.s. sheet 1 mm thickdouble leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of engg. incharge but excluding cost of chowkhats: including two coats of anit corrosive red oxide primer paint. add extra for double leaf shutters 15 glazed window:providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required :partly fixed and partly openable [ fixed area not to exceed 33%] 16 wire gauge supplying & fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150 mm distance. 17 guard bars: p&f square bars or other flat welded to window/ventilators etc. 18 kota stone slab flooring 25 mm thick over 20mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement: 4 course sand ) for area 2001 to 5000 sq. cm 19 kota stone slabs 25 mm thick in risers and stepsskirting, dado and pillars laid on 12 mm (average)thick cement mortar 1:3(1 cement: 3 course sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs , including rubbing and polishing completefor areaof each slab upto2001 sq. cm 20 terrazo tiles over roof: providing and fixing 20 mm thick precast terrazo tiles of approved make, with marble chips of size up to 6 mm laid over roof with neat cement slurry mixed with pigment to match the shade of the tiles , including cutting, grinding rubbing with machine complete on 20 mm thick bed of cement sand mortar 1:4. 21 providing & fixing ist quality standard white, gray, ivory,fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 and is: 15622 of size 300mm x 200mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of tile complete (excluding the cost of cement plaster on walls and piller) 22 internal plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished : 12 mm thick 23 external plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished : 20 mm thick 24 plaster(ceiling): 6 mm thick cement plaster to ceiling of mix 1:3(1 cement: 3 fine sand) 25 black board : plaster on new surface on wall in cement sand mortar 1:3 including raking of joints etc. complete fine finish: 12 mm thick 26 grading roof for water proofing treatment withwater proffing compound: cement concrete 1: 2: 4 (1 cement: 2 course sand: 4 greded stone aggregate 20 mm nominal size) 27 gola: providing gola 75mm x 75mm in cement concrete 1:2:4(1 cement: 2 coarse sand: 4 stoneaggregate 10 mm and down gauge) including finished with cement mortar 1:3(1 cement: 2 fine sand) as per standard design. 28 internal finishing: distempring with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding new work ( two or more coats ) over and including scrapping and priming coat with cement primer. 29 exterior finishing : finishing walls with acrylic smooth exterior paint of rquired shade including all scaffolding .new work ( two or more coat applied @ 1.67 /lit/10 sqm. ) 30 putty: providing and applying white based cement putty over plastered surface to prepare the surface even and smooth complete. 31 painting on doors, windows & ramp raling : painting with syntheitic enamel paint of approved brand and manufacture in all shade to give an even shadenew steel work (2 or more coat on new work). 32 copping: cement concrete flooring 1:2:4 (1 cement: 2 course sand: 4 greded stone aggregate) finishing with a floating coat of neat cement including cement slurry, making of lines or groove etc. complete but excluding the cost of nosing of steps etc. complete : 40 mm thick with 20 mm thick nominal size aggregate. 33 for rain water p&f rigid pvc pipe (is:4985 mark) class ii/ (4 kg. /cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia 34 for rain water p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: bend 87.5110mm dia 35 pipe clip110 mm dia 36 providing and laying factory made chamfered edge plastic coated designer cement concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method, to attain superior smooth finish using pu or equivalent moulds, laid in required grey/yellow/red or any other colour & pattern over 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per manufacturer’s specifications & direction of engineer in charge: 37 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 200mm x 300mm in walls, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 38 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 39 part c (sanitary item)provinding and fixing3 layer pp r (polyproylene random copolymer) pipes sdr 7.4 uv stabilized & antimicrobial fusion welded, having thermal stability for hot and cold water supply including all pp r plain and brass threaded polypropylene random fittings and fixing the pipe with clamps at 1.00 spacing. this includes testing of joint complete as per direction of engineer incharge.(internal work exposed on wall)pn 16 pipe, 25 mm od 40 provinding and fixing3 layer pp r (polyproylene random copolymer) pipes sdr 7.4 uv stabilized & antimicrobial fusion welded, having thermal stability for hot and cold water supply including all pp r plain and brass threaded polypropylene random fittings and fixing the pipe with clamps at 1.00 spacing. this includes testing of joint complete as per direction of engineer incharge.(internal work exposed on wall)pn 16 pipe, 16 mm od 41 p & f squatting pan ( indian type ) white glaze viterous china 1st quality w.c. pan ( is: 2556 mark) with 100 mm viterous chinap or s trap including cutting & making good the wall & loor (excluding a pair of foot rest ) size 510 mm 42 p & f wvc wash basin (1st quality, i.s. : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p. pillar cock (is : 8934 mark) & 32 mm c.p. brass waste coupling of approved make,25 mm g.i. waste pipe complete including cutting & making good the wall.: 450 x 300 mm 43 p & f bib cock (is : 8931 mark) superior quality of approved make.c.p. brass 400 gm, 15 mm nominal bore. 44 p & f inlet connection (angle valves) superior quality of approved make c.p. intel connection 15 mmbrass(is : 8931) 45 p&f rigid pvc pipe (is:4985 mark) class ii/ (4 kg. /cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia 46 p& f waste coulping with fittings of approved quality /make:c.p. brass 40 mm dia 47 p& f waste pipe with all fittings of approved quality /make: p.v.c. with c.p. nut 40 mm dia 48 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: bend 87.5110mm dia 49 pipe clip110 mm dia 50 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant plain floor trap 110 mm dia 51 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant p trap 110 mm dia 52 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant vent cowel 110 mm dia 53 p & f ist quality wvc urinal ( is:2556 mark) with 25mm dia g.i waste pipe dome couplings, concealed iron brackets or screws etc. complete. 54 s/f rccmain hole covers with frame of approved make (light duty) size 450x450 mm 55 p/f grating of approved quality stainiese steet sheet size 125 mm dia 56 construction of soakage well in alltypes of soil of approved drawing , top 90 cm portion in 450 mm thick with cement mortar 1:6 80 mm stone slab coveringjointing of slab in cm 1 : 3, ralthal, kharanja, 40 mm thick m 15 grade c.c. flooring earthwork etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr.inner dia 90 cm & 10 to 12 m deep 57 construction of chamber in all types of soil with 300 mm thick masnory in cm. 1 : 6, 100 mm thick c.c. 1 : 5 : 10 in foundation , 20 mm thick inside plaster in cm 1 : 6, finished with floating neat cement 50 mm thick m 15 grade c.c. flooring earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr.inside size 300 x 300 mm depth upto 0.5 m & 5 kg ci cover with frame. 58 p & f ball cock (is : 1703 mark) with rod & p.v.c. ball complete.brass wt. 400 gm, 15 mm 59 p & f 15 mm dia connection pipe of approved quality make pvc pipes with nuts 450 mm. 60 p & f stop cock (is:8931 mark),superior quality and of approved mark: brass 400 gm. 15 mm nominal bore 61 p&f gi pipes (external work) with gi fittings excluding union (si: 1239 mark) including trenching and refilling each etc. 15 mm dia nominal bore b class 62 p & f pvc storage tank isi marked ( is: 12701) indicating the bis license no. of approved make with cover, 25mm dia 1 m long g.i. overflow pipe & 25 cm longwash out pipe with plug & socket including making connection etc. complete of approved design 500 litres capacity 63 wiring of light point/fan point/exhaust fan point/ call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade and 1.5 sq. mm nominal size fr pvcinsulated unsheathed flexible copper earth conductor 1.1 kv grade (is: 694) of approved make group 2 light point short point (up to 3 mtr.) 64 medium point (up to 6 mtr) 65 long point (up to 10 mtr) 66 fan point short point (up to 3 mtr.) 67 fan point medium point (up to 6 mtr) 68 long point (up to 10 mtr) 69 wiring of 3 pin 5 amp. light plug point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade and 1.5 sq. mm nominal size fr pvcinsulated unsheathed flexible copper earth conductor 1.1 kv grade (is: 694) of approved make in surface/reces group on board 70 s & f follwing sizes (dia.) of isi marked medium duty pvc conduit along with accessories in surface/ recessed using clamps, fastener as required including cutting the wall , covering conduit with wire mess and making good the same as required. group 225 mm dia 71 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor isi marked (is:694) of 1.1 kv grade and approved make in existing surface ofr necessed conduit/ casting capping including making connections etc. as required. group 2 (1 x 1.5 sq. mm) 72 2 x 1.5 sq. mm 73 2 x 2.5 sq. mm 74 p & f 240/415 v mcb of breaking capacity not less than 10 ka (b/c/d tripping characteristic) isi marked is 8828 (1996)/conforming to iec 60898 in existing board/ sheets including making connections with lugs, testing etc. as required. group 2 6 a to 32 a rating 75 p & f recessed/ surface mounting heavy duty horizontal type sheet steel distribution board phophatised/ powder painted complete with 100 amp copper copper bus bar, shorting link, neutral, earth link and din bar, conforming to is 13032 & is 8623 including making internal db termination with copper lux, testing etc. as reqd. . group 2single door(single phase) 8 way 76 p & f strip fluorscent tube fitting fabricated from (crca sheet and finished with powder coating/stove enamelled non corrosive uv resist ep channel)complete with accessories(low loss copperchoke, starter, starter seat)/electronic choke with terminal block duely prewired with copper conducter including making connection, testing etc. as required(without tube)1x36 watts with occb. group 2 77 p & f fluorscent tube rod in existing fixtures as required, minimum 3 star rating,36/40 watts 78 p/i aying pvc insulated & pvc sheathed cable of 1.1 kv grade with aluminium conductor of is:1554 p i of groups of approved make in ground as per is:1255 including excavation of 30cm x 75cm size trench, 25cm thick under layer of sand, iind class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size 6 sqmm, 4 core arm 79 p & f star rated double ball beari;ng capacitor start, aluminium bodyand blade ceiling fan with down rod upto 30 cm with 3x1.5 sqmm pvc insulated flexible copper conductor making connection testing etc as required.1200 mm sweep 3 star rated 80 p & f is:371 marked 6 amp suffacetype celling roseinculuding making commection testing etc. grup 2 (e071400) 81 p & f isi marked 6 amp bakelite batten/ angle holder including making connextion testing etc as required 82 p & f 18 swg ms recessed fan box, hexagonal/round of size 130mm dia, depth 75 mm , 12mm dia rad fan hookwith 100mm length extended on eeach side. gourp 1 83 p & f 18 swg sheet steel boxes duly finisded with two coats of red oxide and with earthing terminal of following sizes (nominal size) on surfacae or in recessed as required. 175 mmx 100 mmx60 mm 84 p & f paper phenolic resin bonded laminates confirming to is: 2036 1995 for boxes/frames including making holes for switches etc with brass screws washers/zink plated nut and bolts as required with 3mm thick ...

Military Engineer Services - Rajasthan

35867627 provision of external service for five ifs sites at af stn jaisalmer surface excavation not exc. 30cm deep & averaging 15 cm deep in soft / loose soil and getting out complete all as specified and as directed . 2 excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth , for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, laying of cables etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and as directed 3 returning, filling in approved soft / loose soilincluding spreading, leveling, watering and well ramming in layers each n.exc 25cm complete all as specified and as directed . 4 removing surplus soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed . 5 labour only ( except material for road side berms of 100 mm spread thickness with available approved soil / moorum obtained from within md land as directed spread rolled and consolidated to gradient and camber required etc complete all as specified and as directed by engineer in charge.note 1.approved soil / moorumshall be obtained from within md land as directed 2. no lead charge or charge of whatsoever nature shall be paid on this account. 6 factory made kerb stone of m25 grade cement concrete in postion to the required level and curvature , jointed with cement mortar 1:3 including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm ) including making drainage opening wherever requiredincluding demolition of existing kerb stone complete all as specified and directed. 7 preparation of newly surface of road side kerb stone and applying two coats of synthethic enamel paint of approved different tint and pattern over a coat of primer etc complete all as specified and directed. 8 hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rolled to a true surfacecomplete all as specified and as directed . 9 75 mm thick pcc ( 1:4:8 ) type d 2 using 40mm graded stone aggregate as in sub base including finishing the top surface of concrete even and roughcomplete all as specified and as directed . 10 60mm thick m 35 grade machine pressed with grey cement and no pigment interlocking factory made paver blocks of any size and shape conforming to is 15658 2006, set, jointed and pointed in dry sandover and including 25 mm thick sand cushion complete all as specified and as directed . 11 excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth , for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, laying of cables etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in hard / densesoil complete all as specified and as directed 12 galvanized steel water tubing medium grade isi marked of 100mm bore with & including all necessary fittings complete, laid in trenches, complete all as specified and directed.note : excavation & earthwork shall be measured & paid for separately under relevant items of this schedule. 13 galvanized steel water tubing medium grade si marked of 40mm bore with & including all necessary fittings complete, laid in trenches, complete all as specified and directed.note : excavation & earthwork shall be measured & paid for separately under relevant items of this schedule. 14 galvanized steel water tubing medium grade si marked of 25 mm bore with & including all necessary fittings complete, laid in trenches, complete all as specified and directed.note : excavation & earthwork shall be measured & paid for separately under relevant items of this schedule. 15 cast iron body sluice valve heavy duty class ‘pn 1.6’, 100mm bore, isi marked with confirming to is 14846 2000, both flanged ends and drilled, high tensile stainless steel spindle, cast iron gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts ( high tensile ) , washers etc, and testing, includingtaking out old unserviceable sluice valve of 100mm bore, complete all as specified anddirected. 16 gun metal globe or gate valve, with iron wheel head, screwed both ends, isi marked for 40mm bore pipe linecomplete all as specified and directed. 17 gun metal globe or gate valve, with iron wheel head, screwed both ends, isi marked for 25mm bore pipe linecomplete all as specified and directed. 18 cutting existing steel tubing for alteration or addition ( each cut measured ) complete all as specified and directed. 19 screwing existing steel tubing foralteration or addition ( or lengthening screw on pipe to from connector ) complete all as specified and directed. 20 construction of stone masonary valves pit of size 900mmx 900mm x 900mm ( internal dimention of chamber ) made with bulit in cement mortar 1.6 for sluice valve chamber including necessary excavation, foundation concrete in pcc 1:4:8 type d2 using 40mm graded stone aggregate for foundation and 15mm thick inside cement plaster with cement mortar 1:4 with floating coat of near cement, pcc coping type b1 ( 1:2:4 ) using 20mm graded stone aggregate including necessary form work with ms frame with angle iron 50x50x6 mm and cover of ms sheet 3.15mm thick including tarring and painting ( where required ) the steel surface with two coats of synthetic enamel paint over a coat of red oxide prime complete as specified and locking arrangement directed. 21 cutting existing pipe of any type and size and tapping of pipe line by providingof tee gi of size 100 x 100 x100 mmcomplete all as specified and directed. 22 pcc 1:2:4 type b 1 using 20mm graded stone aggregate as incopingof poles / pipe / plateform / path etc i including necessary use and waste of formworkand finishing the top surface of concrete even and smooth with using extra cement complete all as specified and as directed . 23 sand cushioning and cover ( using local tibba sand ) , 80 mm thick before laying of cable and 150 mm thick after the cable is laid, complete all as specified and as directed by engineer in charge. ( note :1. approved local tibba dry sand after removal of vegetations, grass and other deleterioussubstances shall be used for sand cushioning and cover ) . 24 jodhpur stone rough dressed slab, 40 cm to 50 cm thick, 25 cm to 35 cm wide of 80 cm long dry abuttting each other for protection to under groung cable, complete all as specified and as directed . 25 supply, laying, jointing and testing xlpeinsulated screened pvc bedded, armoured, heavy duty underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 35 sq mm 3.5 core confirming to is 7098 ( part i 1988 ) laid in trenches, along poles through pipes etc. complete all as specified. notes : ( i ) sand cushioning, cable protection, gi pipe and excavation & earth work shall be measured & paid for separately ( ii ) road cutting / floor cutting / cutting holes etc in walls required for laying / fixing of cable etc shall be made good as per existing. nothing extra shall be admissible on this account. quoted rates shall be inclusive of the above provisions. 26 supply, laying, jointing and testing xlpeinsulated screened pvc bedded, armoured, heavy duty underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 50 sq mm 3.5 core confirming to is 7098 ( part i 1988 ) laid in trenches, along poles through pipes etc. complete all as specified. notes : ( i ) sand cushioning, cable protection, gi pipe and excavation & earth work shall be measured & paid for separately ( ii ) road cutting / floor cutting / cutting holes etc in walls required for laying / fixing of cable etc shall be made good as per existing. nothing extra shall be admissible on this account. quoted rates shall be inclusive of the above provisions. 27 supply, laying, jointing and testing xlpeinsulated screened pvc bedded, armoured, heavy duty underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 185 sq mm 3.5 core confirming to is 7098 ( part i 1988 ) laid in trenches, along poles through pipes etc. complete all as specified. notes : ( i ) sand cushioning, cable protection, gi pipe and excavation & earth work shall be measured & paid for separately ( ii ) road cutting / floor cutting / cutting holes etc in walls required for laying / fixing of cable etc shall be made good as per existing. nothing extra shall be admissible on this account. quoted rates shall be inclusive of the above provisions. 28 40 mm bore gi tube, light grade galvanised with clamp of 25 x3 flat ironfor protection of cable , with all fitting leadin trenches / under road / with wall / in wall / pole / under floorwhere requiredcomplete all as specified and as directed 29 80 mm bore gi tube, light grade galvanised with clamp of 25 x3 flat ironfor protection of cable , with all fitting leadin trenches / under road / with wall / in wall / pole / under floorwhere requiredcomplete all as specified and as directed 30 drilling ( horizontally ) of holes under road 110 mm dia , pavement , hard standing by trench less technology ( manually ) with out disturbing the top surface of road ( maxium 10 mtr wide ) for laying of cable / gi pipescomplete all as specified and as directed . 31 earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground ( earth pit not less than 2.25m deep below ground level ) with top edge of plate not less than 1.5 deep below normal ground level and connected to and including galvanized earth lead wire 4mm dia upto 7.5 metre by means of gi nuts, bolt, check nuts, washers thimbles, etc as shown in electrical plate no 03 ssr part i and connection to main switch board or panel and testing on completion including excavation and earth work in any type to soil, returning fitting in and removal of surface spoil to a distance not exc 50 metre, pcc chamber ( 1:3:6 ) type c 2, charcoal and salt mixed layer 15cm thick all around the earth plate electrode, ms funnel with wire mesh, gi pipe light grade 20mm bore for watering and 15mm bore meter long gi pipe light grade for earth wire protection fixed with poles with two clamps, made from ms flat 25mm x 3mm, bolts, nuts and washers 75mm thick rcc cover 1:2:4 type b 1 shall be provided on ci frame etc complete all as specified. note pcc chamber shall be constructed at least 1.5m away from the earth electrode.the pipe for watering shall be provided in slanting manner.including the cost of 7.50m gi pipe for protection of earth wire / strip 32 earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground , ( earth pit not less than 2.25 meter deep below ground level ) with top edge of plate not less than 1.5 meter below normal ground level , connected to and including galvanised iron earth wire 32 x 6 mm by means ofnut, bolts, check nuts and washers of galvanised iron or steel and provision of charcoal dust and common salt packed all around the earth plate including necessary excavation and earth work in any type of soil and testing complete all as specified and directed and shown in electrical plate number 5 of mes ssr part i ( 1991 ) note: ( a ) excavation and earth work for drilling hole for electrode in any type of soil. ( b ) pcc pit in cement concrete 1:2:4 type b 1, pre cast rcc cover with suitable handle 40 mm thick in pcc 1:2:4 type b 1, reinforced with welded steel wire fabric weighing not less than1.87 kg / sq meter. ( c ) funnel with watering pipe of gi 20 mm nominal bore light grade and lugs etc complete all as specified and directed ( d ) 40 mm nominal bore medium grade gi protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. ( e ) requisite quantity of common salt and charcoal. ( f ) testing of earthing. 33 sub main wiring with 2 run of single core 6.0 sqmm multi stranded copper conductor 1100 volts grade frls pvc insulated unsheathed cable drawn through and including pvc conduit of suitable size onwall isurface ncluding 4.0 sqmm pvc insulated unsheathed single core copper conductor earth wireincluding taking down old unserviceable submain wiring complete all as specified. note : two run of 6.00 sqmm cable and one run of 4.00 sqmm cable as earth wire continuity conductor and stove enamelled steel conduit shall be measured & paid as one unit. 34 sub main wiring with 4 run of single core 6.0 sqmm multi stranded copper conductor 1100 volts grade frls pvc insulated unsheathed cable drawn through and including pvc conduit of suitable size on wall surface includingtwo run of 4.0 sqmm pvc insulated unsheathed single core copper conductor earth wire in and including taking down old unserviceable submain wiring complete all as specified. note : four runs of 6.00 sqmm cable and two run of 4.00 sqmm cable as earth wire continuity conductor and stove enamelled steel conduit shall be measured & paid as one unit. 35 sheet metal enclosureflush mounting factory made for tpn db 4 way, 415 volt, ac 50 hz double door, ip 43 protection, ik 09 built in bus bar completewith siitable for incomming mcb and outgoing mcbs and fixed in recess on wallcomplete all as specified and as directed . 36 mcb, tpn, 5 to 32 amps rating, with over load and short circuit protection c curve and rupturing capacity 10 ka, 240 volt grade, ac supply, 50 hz and making connections using suitable size copper lugs / thimbles including complete, all as specified & directed. 37 mcb, single pole, 5 to 32 amps rating, with over load and short circuit protection c curve and rupturing capacity 10 ka, 240 volt grade, ac supply, 50 hz and making connections using suitable size copper lugs / thimbles including complete, all as specified & directed. 38 supply and fix cable jointing kit for 1.1 kv grade cable for straight through joint complete with jointing material heat shrink type and accessories suitable for 3 ½ / 4 core xlpe, armoured, aluminium conductor cable of size 185sqmm complete all as specified and directed. 39 mcb, single pole, 40 to 63 amps rating, with over load and short circuit protection c curve and rupturing capacity 10 ka, 240 volt grade, ac supply, 50 hz and making connections using suitable size copper lugs / thimbles including complete, all as specified & directed. 40 design, supply, erection, commissioning and testing of outdoor type lt feeder pillar box, double door, suitable for 3 phase 4 wire, 415 volts ac supply and having 4 nos copper bus bar not less 150 amps for distribution system and type tested at cpri, fabricated in factory having modern fabrication and testing facility which includes seven ( 07 ) tanks pre treatment facility comprising of de greasing, rinsing, de rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting ( thickness not less than 80 micron ) with approved shade of ral 7032.the feeder pillar shall be provided with suitable neoprene rubber gasket to make it completely dust and vermin proof and degree of protection not less than ip 55 and general construction conforming to is : 13947. the feeder pillar shall be made out of 3.15mm thick crca mild steel sheetand 3.15mm thick gland plate duly compartmentalized for each control gear and bus bar, front door ( 02 layer ) and rear door ( 01 layer ) opening facility and 4 side slanting canopy type roof on top and mild steel channel ( 75 mc ) base frame at bottom and having welded equal angle of 75mmx75mmx6mm of length 0.9mtr, 04 nos, 30cm ofangle shall be embedded in pcc 1:2:4, 20mm graded stone agregate below gl level and 30cm shall be above ground level of size as directed by engr in charge at site. the feeder pillar shall be provided with ventilation facility in the form of louvers for better heat dissipation.necessary cable gland shall be provided for all incoming and outgoing cables. 41 control wiring : all control wirings shall have to be carried out with 1100 volts rated frls grade pvc insulated multi stranded type copper wire of cross sectional area 1.50sqmm and shall be properly bunched, tied and dressed, ferrule marked for proper identification and crimped with suitable size and type of tinned copper lugs and shall be wrapped with pvc spring type tube near the door hinges.cable alley : necessary cable alley shall be provided for out going cables in both sides of lt panel with terminal block, the terminal block shall be connected with the outgoing mccb with copper bus bar of suitable size incoming : mccb 100 amps, 4 pole , thermal magneticrelease, 16 ka, adjustable, 70% to 100% 1 nos outgoings : ( a ) mccb 63 amps, 4 pole , thermal magneticrelease, 16 ka, adjustable 70% to 100 % 2 nos ( b ) mccb 40 amps, 4 pole , thermal magneticrelease, 16 ka, adjustable 70% to 100% 1 nos ( c ) bakelite fuse holder with 5 amps hrc type control fuse 03 nos. ( d ) led pilot lamp suitable for 230 volts ac supply with integral circuit and cluster led of following colours : ( i ) red 01 no, ( ii ) yellow 01 no, ( iii ) blue 01 no. ( e ) digital volt meter 96mm x 96mm suitable to read 0 to 500 volts, accuracy class 1% 01 nos ( f ) digital ammeter 96mm x 96mm suitable to read 0 to 100amps, accuracy class 1% 01 nos ( g ) current transformer ( ct ) of rating 100 / 5, tape wound, rated burden 5 va 03 nos ( h ) led indicator lamps complete with integral circuit and cluster led, suitable to operate in 230 240 volts ac supply 1set of 03 nos ( red 01, yellow 01, blue 01 ) ( j ) 02 nos.danger notice plate duly written in signal red colour on aluminium plate in english and hindi language and of size not less than 150mmx100mm shall be fixed on both front & rear door of the bus bar chamber. ( note : 1. the feeder pillarbox shall be designed in such a way that adequate workable space is made available inside the compartments and the front area of the panel shall not be less than 1.00 sqm and 500mm depth ) .2. the contractor shall submit lt panel / feeder pillar boxdrawings to the engr in charge for approval before procurement of material. 42 plain cement concrete ( 1:2:4 ) type b 1 ( using 20mm graded stone aggregate ) in lintel, cill, bed block coping , bed plate, bond stone etc including weathering slightly rounded or chamfered angles and throating and necessary form workcomplete all as specified and as directed ....

Military Engineer Services - Rajasthan

35724087 repair to fencing, path and other misc works at air force station jodhpur 1.00 excavating in post holes ( or similar holes ) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in any type of soil complete all as specified & as directed. 2.00 m&l for pcc 1:3:6 type c2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified & as directed. 3.00 dismantling posts or struts embedded in concrete, wood, steel or r.c.c. of any section, including taking out embedded portion and making good disturbed surface etc., complete all as specified & as directed. 4.00 s&f mild steel work as in angle iron in posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets ( for securing wire mesh etc. ) and similar works conforming to grade e 165 ( fe 290 ) , complete, all as specified & directed. 5.00 s&f mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanging, also fastening and fixing, conforming to grade e 165 ( fe 290 ) , complete all as specified & as directed. 6.00 s&f in repair galvanized 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to mild steel fencing posts, any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel nibs, pins etc complete all as specified & directed. note : each line of horizontal / vertical / diagonal wire to be measured for the purpose of payment. 7.00 m&l for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide primer complete all as specified. 8.00 supply only mild steel galvanized chain link fencing of 3.15mm dia of mesh wire, mesh size 100x100mm complete all as specified and as directed. note: flat iron, round tie bars, nut bolts and washer shall be measured and paid for separately. 9.00 fixing only mild steel galvanized chain link fencing, any mesh, size and type to any type of standards, rails, straining bolts etc. including provision of binding wire. note : supply only chain link fencing shall be measured and paid for separately. 10.00 s&f mild steel screw bolts ( machine made ) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5 cm long and dia of neck 11 to 15 mm complete all as specified 11.00 s&f in repair razor type concertina coil hot galvanised spring tensile wire fixed on y shape angle iron having barbed wire and coil having 6 to 8 rm per coil of 900 mm dia and minimum weight 7.5 kg / coil etc., complete all as specified & as directed. 12.00 m&l for mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips. 13.00 m&l for preparation of new untreated steel and iron surfaces of any description, not exc. 10 cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint complete all as specified & as directed. 14.00 demolition of plain cement concrete in ground floor and pavings not exc 15 cm thick ( below or above ground level ) including floor tiles of any description complete all as specified. 15.00 m&l for 100 mm thick pcc 1:4:8 type d2 using 40 mm graded crushed stone aggregate in foundations, sub base, filling and mass concrete. 16.00 m&l for factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of grade m 35 made in rubber mould / rubberised type, conforming to is 15658 2006 of shape and size as directed with grey cement and no pigment laid over & including 30 mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed. 17.00 m&l for cement concrete 1:2:4 type b1, using 20mm graded crushed aggregate as in copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work ( straight or curved ) all exposed surface of concrete finished fair complete all as specified & as directed....

Vardhamum Mahaveer Open University - Rajasthan

35717238 tender for misc. civil works in sabhagar bhawan 1 demolishing brick work manually by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. in cement mortar. 2 dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. 3 dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: for thickness of tiles 10 mm to 25 mm. 4 demolishing cement concrete manually by mechanical means including disposal of material within 50 metres lead as per direction of engineer in charge. 1:3:6 or richer mix. 5 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in : cement mortar 1:4 ( 1 cement : 4 coarse sand ) 6 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick. 7 half brick masonry in superstructure, above plinth level upto floor vlevelusing bricks of designation 75 cement mortar 1:4 ( 1 cement : 4 coarse sand ) 8 supplying and fixing stone lintels / bed plates of approved quarry rough dressed in cement mortar 1:4 upto 15 cm thick. 9 providing and fixing steel gate, grating, and grills made of angles, tees, square bars, flats or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 10 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 200mm × 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete ( excluding the cost of cement plaster on walls and pillar ) . 11 extra for using size above 200×300mm in glazed tiles and for using 400mm × 400mm mat finished tiles in place of 300mm × 300mm size. 12 providingandfixing75 mm wide decorativeborderindifferentshadesandin allcolouresinglazedtiles laid over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white mixed with pigment of matching shade complete. 13 providing and fixing 1st quality mat finished ceremic tile size 300×300mm confirming to is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete ( including the cost of cement mortar bed 1:4 ) . 14 extra for using size above 200×300mm in glazed tiles and for using 400mm × 400mm mat finished tiles in place of 300mm × 300mm size. 15 p & f 1st quality vitrified porcelain polished tiles on floor, skirting and steps etc. in different sizes ( thickness to be specified by manufacturer ) with water absorption less than 0.08% and conforming to is:15622 of approved make in all colour and shade, laid with 20 mm thick cm 1:4 including grouting the joints with white cement and matching pigment etc complete. size 600 mm × 600 mm. 16 supplying and filling in plinth with blown sand under floors including watering ramming consolidating and dressing complete including cost of sand. 17 random rubble dry stone kharanja under floor. 18 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m 20 grade nominal mix 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size ) . 19 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m 10 grade nominal mix 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size ) . 20 providing and fixing aluminum work for doors, windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is:733 and is:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gap at junctions, at top, bottom and sides with required pvc / neoprene felt etc. aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws al. tower bolt & al. handle & al. aldrop etc., all complete as per architectural drawings and the directions of engineer in charge. ( glazing and paneling to be paid for separately ) . powder coating aluminum ( minimum thickness of powder coating 50 micron ) 21 providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm × 6.0mm and opening of size 102mm × 99mm to aluminum window / vent with required screws, y and h aluminium section ( as per drawing ) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge. powder coating aluminum ( minimum thickness of powder coating 50 micron ) 22 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with pvs / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge. ( cost of aluminium snap beading shall be paid in basic item ) with float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg / sqm ) 23 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure a: 30 mm thick. commercial veneer both side 24 extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters ( over all area of door shutter to be measured ) over item no. 8.13. 25 providing and fixing is : 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. 26 providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete. new plastered surface ( three or more coats ) 27 painting exterior surface of wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including preparation of base with sand papering, primer, putty, etc. complete in all respect including scaffolding and safety provision. new work. 28 painting exterior surface of wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including preparation of base with sand papering, primer, putty, etc. complete in all respect including scaffolding and safety provision. old work. 29 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding : two or more coats on new work including preparation of base with primer, putty, lippy etc. complete in all respect. 30 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: old work ( one or more coats ) 31 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work. 32 french sprit polishing : two or more coats on new work including a coat of wood filler. 33 providing and fixing stainless steel railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) . ( a ) grade 304 34 providing and fixing aluminum work for doors, windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gap at junctions, at top, bottom and sides with required pvc / neoprene felt etc. aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws al. tower bolt & al. handle & al. aldrop etc., all complete as per architectural drawings and the directions of engineer in charge. ( glazing and paneling to be paid for separately ) . anodised aluminum ( anodised transparent 81 dyed to required shade according to is : 1868. ( minimum anodic coating of grade ac 15, anodizing to be got done from approved anodizer ) 35 providing and fixing 25 mm thick non slippery reflective type designer paving tile with metallic hardening using 2 kg / sq. mtr made out of cement concrete of required grade, sizes of tile upto 300×300 mm manufactured with wet cast vibration system in two layers and laid over base of 20 mm thick cement morter1:4 using neat cement slurry in cluding finishing of joints etc. complete. using m 40 grade cement concrete. 36 providing and fixing stone slabs table rubbed, 15 18 mm thick in walls, steps, pillars, counters, jambs, shelves, sills etc. laid on 12mm ( av. ) thick base of cm 1:3 ( 1 cement : 3 coarse sand ) jointing with white cement mortar 1:2 ( 1white cement : 2 marble dust ) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. makrana adanga. above 3601 cm2 slabs 37 p & f european type white glazed vitreous china 1st quality w.c pan ( is : 2556 mark ) with p or s trap including cutting and making good the wall and floor 38 providing & fixing premium quality white glazed vitreous china sanitary wares ( is:2556 mark ) of approved make as per direction of engineer in charge including cutting and making good the wall and floor. wall mounting european type w.c. 39 supply of hydraulic seat cover for european wc of superior quality approved make in white colour 40 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer in charge. health facet ( premium heavy quality ) as approved by engineer in charge 41 p & f c.p. brass urinal spreader for large urinal of heavy duty of approved make as per direction of engineer in charge 42 providing & fixing concealed cistern with floor mounting frame and flush plate of superior quality and approved sample by engineer in charge. 43 p & f water closet seat covers with brass hinges complete : solid pvc ( is 2548 marked ) grade i white for ewc. 44 providing & fixing premium quality bottle trap internal portion 32mm, size 250mm long wall connection pipe & wall flange as per approved by engineer in charge. 45 providing & fixing premium quality wvc urinal with pvc waste pipe, dome couplings, concealed iron brackets or screws etc. complete. flat back ( large ) or half stall size 590×375×390 mm. 46 providing & fixing premium quality wvc wash basin with c.i. brackets duly painted & 32 mm c.p. brass waste coupling of approved make with pvc waste pipe complete. size 550 mm × 400 mm dia for counter top. 47 p & f wvc wash basin ( ist quality is:2556 mark ) of approved make with c.i. brackets duly painted 1 no. 15 mm c.p. pillar cock ( is:8934 mark ) & 32 mm c.p. brass waste coupling of approved make, p.v.c waste pipe with pvc nut 32 mm complete including cutting & making good the wall : size 550 mm × 400 mm 48 p & f low level flushing cistern of 10 litres capacity ( is : 2556 mark ) of approved make with complete fittings c.i. brackets duly painted, brass ball cock with ball ( is: 1703 mark ) complete including cutting and making good the wall : pvc with pvc withpvcbend and superior internal fittings as per is : 7231. 49 p & f c.p. brass urinal flush pipe set complete with flanged brackets of approved make. for 1 urinal 50 p & f looking mirrors with p.v.c. frame of approved make as per direction of engineer in charge. round 500mm dia 51 p & f toilet shelf of approved quality / make. acrylic shelf on c.p. brass casted brackets & guard rail of approved make as per direction of ei ofsize 550×125mm 52 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer in charge. jet spray ( premium heavy quality ) as approved by engineer in charge 53 providing and fixing premium quality towel rack 600mm long 260mm wide with lower hangers cp brass fittings of approved make as per direction of engineer in charge 54 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer in charge. 600 mm long towel rail 55 p & f grating of approved quality / make: stainless steel sheet size 125mm dia. 56 p & f liquid soap container with brackets complete of approved make: c.p. brass. 57 p & f tooth paste & brush holder of approved quality / make: c.p. brass ( heavy and superior quality ) 58 p & f toilet paper holder with rod of approved quality / make: c.p. brass heavy & superior quality. 59 p & f soap dish or tray of approved quality / make. wvc ( 1st quality, is 2556 marked ) recessed size 150×150 mm. soap dish 380 mm. 60 p & f extension pipe for bib cocks of approved quality / make. c.p. brass of heavy & superior quality 150×15 mm. 61 providing & fixing c.p. flange for 15mm dia taps. 62 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer in charge. central hole basin mixer 63 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer in charge. bib cock with long thread 15 mm nominal size 64 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer in charge. long body bib cock 15 mm nominal size 65 p & f stop cock ( is : 8931 mark ) , superior quality & of approved make : brass 400 gm 15mm nominal bore. 750 gm. 20 mm nominal bore. 66 p & f ball cock ( is:1703 mark ) with rod & p.v.c. ball complete : brass wt. not less than 800 gm, 32mm. 67 p & f inlet connection ( angle valves ) superior quality, of approved make, for wash basin, gyser etc. c.p. inlet connection 15mm brass ( is : 8931 marked ) with 37 cm long pipe and nut. 68 p & f 15 mm dia connection pipe of approved quality / make : pvc pipe withc.p. brass nuts upto length, 600mm 69 p & f full way valve ( is:778 mark ) or wheel valve of approved make : gun metal 20 mm nominal bore. 70 p & f full way valve ( is:778 mark ) or wheel valve of approved make : gun metal 25 mm nominal bore. 71 p & f pvc storage tank isi marked ( is : 12701 ) indicating the bis license no ) , of approved make with cover, 25mm dia 1m long g.i. over flow pipe & 25 cm long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500 litres capacity. 72 hoisting charges for each floor : for items 2.26.1 to 2.26.4 73 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer in charge. two way bib cock 15 mm nominal size 74 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer in charge. revolving type towel ring 75 providing and fixing superior quality cp brass fittings of approved make as per direction of engineer in charge. double coot hook. 76 providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes ( is 15778 : 2007 code ) having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. ( concealed work including cutting chases and making good the walls etc., ) 15 mm nominal size 77 providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes ( is 15778 : 2007 code ) having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. ( concealed work including cutting chases and making good the walls etc., ) 20 mm nominal size 78 providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes ( is 15778 : 2007 code ) having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. ( concealed work including cutting chases and making good the walls etc., ) 25 mm nominal size 79 providing and fixing 3 layer pp r ( polypropylene random coplymer ) pipes sdr 7.4 uv stabilized and antimicrobial fusion welded, having thermal stability for hot & cold water supply including all pp r plain & brass threaded polypropylene random fittings including trenching, refilling and testing of joint complete as per direction of engineer in charge. ( external works ) pn 16pipe, 32 mm od 80 p&f rigid pvc pipe ( is:4985 mark ) class ii / ( 4 kg. / cm2. ) approved quality / makeincluding joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia. 81 p&f rigid pvc pipe ( is:4985 mark ) class ii / ( 4 kg / cm2 ) approved quality / make including joining the pipe with solvent cement rubber ring and lubricant. providing & laying c.c. 1:3:6 ( stone aggregate 20mm nominal size ) all around pvc pipe including 7.5 cm thick bed concrete [ width & height =dia of pipe in cm+15cm ] excluding cost of pipe & excavation of trenches etc. pvc pipe 110 mm dia. 82 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : coupler ( socket ) 110 mm dia. 83 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : plain tee 110 mm dia. 84 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : door tee110 mm dia. 85 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : bend 45. 110 mm dia. 86 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : bend 87.5. 110 mm dia. 87 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : door bend ( top side ) .110 mm dia. 88 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : vent cowel. 110 mm dia. 89 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : socket plug. 110 mm dia. 90 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : pipe clip. 110 mm dia. 91 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : p trap. 110 mm dia. 92 p&f rigid pvc pipe fittings ( is: 4985 mark ) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant : gully trap. 110 mm dia. 93 construction of manhole in all type of soil inner size 90 × 60 cm 300 mm thick masonry in cm 1:6, 10 cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in cm 1:6, finished with floating neat cement, 50mm thick m 15 grade c.c. flooring, making channels, 80mm thick stone slab covering with 40mm thick m 15 grade c.c. flooring, cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. depth up to 0.5 m 94 construction of chamber in all type of soil with 300 mm thick masonry in cm 1:6 m, 10 cm thick c.c. 1:5:10 in foundation, 20mm thick insider plaster in cm 1:6, finished with floating neat cement, 50mm thick m 15 grade c.c. flooring, earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. inside size 300×300 mm depth upto 0.5m cement cover with frame. 95 construction of chamber in all type of soil with 300 mm thick masonry in cm 1:6 m, 10 cm thick c.c. 1:5:10 in foundation, 20mm thick insider plaster in cm 1:6, finished with floating neat cement, 50mm thick m 15 grade c.c. flooring, earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. inside size 450×450 mm depth upto 0.5 mcement cover with frame. 96 construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in cm 1:6, 80mm thick stone slab, jointing of slab in cm 1:3, ralthal, kharanja, 40 mm thick m 15 grade c.c flooring, earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: size 300 cm. dia outside & 300 cm. depth. 97 construction of soakage trench inall types of soilwith 300 mm thick dry stone masonry, 80 mm thickstone slab covering, jointing of slab in cm 1:3 ralthal, kharanja, 40 mm thick m 15grade c.c. flooring earthwork etc. complete as per approved drawing including disposalof earth within a lead of 50 mtr.: top width 180cm., bottom width 90cm. & depth 240cm. 98 construction of septic tank in all types of soil with 40 cm thick masonry in cm 1:6, 15 cm thick c.c bed of 1:5:10, m 15 gradec.c floor &rcc slab covering with m15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in cm 1:6 finished with neat floating cement, 4 nos. stone foot rests of approved design , two no. 450 mm dia each ferro cementcover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr. size 200×100×130 cm. ( for 10 users ) with 115 mm thick rcc ( m 20 ) slab with tor steel reinforcement 8mm ? @15 cm c / c bothways including shuttering complete in all respect....

Rajasthan Tourism Development Corporation Limited - Rajasthan

35354110 various development works at delwada, achalgarh and arbuda dham, mt. abu ( sirohi ) clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared 2 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan ) including disposal of excavated earth, lead upto 50m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed : all kinds of soil 3 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size ) . 4 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in: cement mortar 1:6 ( 1 cement : 6 sand ) . 5 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor five level. thermo mechanically treated bars ( conforming of relevent is code ) 6 centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. 7 columns, pillars, posts and struts etc. 8 suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. 9 providing and laying in position specified grade of cement concrete for all rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excludingthe cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix 10 random rubble dry stone kharanja under floor. 11 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m15 grade nominal mix 1: 2: 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 40mm nominal size ) . 12 filling available excavated earth ( excluding rock ) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. 13 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in allshapes and sizes in : cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) 14 half brick masonry in superstructure , above plinth level upto floor vlevelusing bricks of designation 75 cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) 15 add extra providingand placing in position 2 nos. , 6mm ø m.s. barat every thirdcourse of half brick masonry . 16 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m15 grade nominal mix 1: 2: 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) . 17 providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. m20 grade nominal mix / design mix 18 providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls ( any thickness ) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. m15 grade nominal mix1: 2: 4 ( 1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size ) . 19 providing m 25 grade concrete by using cement as per codal provision instead of m 20 grade design mix. 20 grading roof for water proofing treatment with water proffing compound cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 gradedstone aggregate 20 mm nominal size ) 21 supply and fixing jodhpur sand stone machine cut dash, coping, sill, lintel fixed in cement sand mortar 1:4. 22 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 23 25mm thick. 24 20mm thick. 25 6 mm thick cement plaster to ceiling of mix 1:3 ( 1cement : 3 fine sand ) 26 providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete : new plastered surface ( three or more coats ) 27 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: new work ( two or more coats ) over and including scrapping and priming coat with cement primer. 28 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. 29 painting exterior surface of wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of basewith sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision , new work 30 providing and fixing in cement sand mortar 1 : 4 single paitam ( rebated ) stone doors windows and ventilator frames of approved quarry :size 75 x 60mm 31 providing and fixing stone jali 40mm thick red / pink sand stone throughout in cement mortar 1:3 ( 1 cement : 3 coarse sand ) including pointing in white cement mortar 1:2 ( 1 white cement : 2 stone dust ) with an admixture of pigment, matching the stone shade, jali patterns to be cut square to jali slab without any chamfers etc: 32 kota stone slab flooring 25 mm thick over 20 mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4coarse sand ) for area of each slab from 901 to 2000 sq.cm : 33 kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average ) thick cement mortar 1:3 ( 1 cement 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete : for area of each slab upto 2001 sqcm 34 providing and fixing stainless steel railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) . : grade 304 35 steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m ) fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete. hot finished welded type tubes. 36 providing and fixing t iron frames for doors, windows andventilators of mild steel tee sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 37 providing and fixing to existing door frames 30mm thick factory made polyvinyl chloride ( pvc ) door shutter made of stiles and rails of a upvc hollow section of size 60x30 mmand wall thickness 2mm + / 0.2mm with inbuilt decorativemoulding edging on one side. the stiles and rails mitred andjoined and the corners by means of m.s.galvanized / plastic brackets of size 75x220 mm having wall thickness 1.0mmand stainless steel screws. the stiles of the shutter reinforced byinserting galvanized m.s.tube of size 25x20 mm and 1mm + / 0.1mm wall thickness. the lock rail made up of „h? section, a upvc hollow section of size 100x30 mm and 2mm + / 0.2mmwall thickness fixed to the shutter stiles by means of plastic / galvanized m.s.tube „u? cleats. the shutter frame filled with a upvc multi chambered single panel of size not less than 610mm, having overall thickness of 20mm and 1mm+ / 0.1mm wall thickness. the panels filled vertically and tie bar at two places byinserting horizontally 6mm galvanized m.s.rod and fastened with nuts and washers.complete as per manufacturer?s specification and direction of engineer in charge. ( forw.c.and bathroom door shutter ) 38 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure a : 35 mm thickcommercial veneer both side 39 extra for providing other type of fittings as mention in annexure a ( as approved by ei ) : stainless steel fittings 40 providing and fixing square bars or other flat welded to window, ventilatiors etc. 41 supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 42 renewing glass panes, with putty and nails wherever necessary : float glass panes of thickness 5 mm 43 m 40, 80mm thick to be used in medium traffic ( medium traffic is defined as a daily traffic of 150 450 commercial vehicles exceeding 30 kn laden weight, or an equivalent of 0.5 to 2.0 msa for a design life of 20 years. ) like city streets, small and medium market roads, low volume roads, utility cuts on arterial roads, etccategory „c?not denated on any it?s faces like hexagon, rectangular, square shape as per irc sp 63:2004 44 providing and laying at or near ground level factory made kerb stone of m 25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand ) including making joints with without grooves ( thickness of joints except at sharp curve shall not to more than 5mm ) including making drainage opening wherever required complete including painting etc. as per direction of engineer in charge ( length of finished kerb edging shall be measured for payment ) . ( precast c.c. kerb stone shall be approved by engineerin charge ) . 45 stone work ( machine cut edges ) for wall cladding / veneering work up to 10m height with 20 to 30 mm thick red sand stone ( karauli ) and backing filled with a grout of 12mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) including pointing in white cement mortar 1:2 ( 1 white cement : 2 stone dust ) with an admixture of pigment matching the stone shade : ( to be secured to the backing by means of cramps which shall be paid separately ) exposed face machine cut 46 providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 ( 1 cement : 2 coarse sand ) including making the necessary chases in stone and holes in walls wherever required 47 supplying and fixing machine cut fine dressed red / pink sand stone dasa or coping, with full moulding if required laid on cement mortar 1:4 including pointing with admixture of pigment matching with the stone shade. 75mm thick 48 fine dressed & machine cut edges 30 35 mm thicksand stone flooring over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) jointed grey cement slurry mixed with pigment to match the shade of stone complete as per design drawing and instruction of ei. : red sand stone ( karauli stone ) 49 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting ( height upto 10 m ) , fixing in position and applying a priming coat of approved steel primer all complete:...

Rajasthan State Ganganagar Sugar Mills Limited - Rajasthan

35338085 construction of various civil work under package 1 at kaminpura sugar factory, sri ganganagar , construction of godown ( 30 x 20 ) feetfor winery in rsgsml campus kaminpura district sriganganagar , earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils , providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.a ) m10 grade nominal mix a ) m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size ) . , a ) m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size ) . , b ) m20 grade nominal mix: 1: 1.5: 3 ( 1 cement: 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size ) . , brick masonry with f.p.s. bricks of class designation 75 in foundation and plinth with bricks : cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) . , providing and laying in position specified grade of cement concrete for all rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix , centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. , providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircasesand spiral staircases etc. m20 grade nominal mix / design mix , centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. , brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in : cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) , providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor five level. ( original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to is:1786 ) : cold twisted deformed bars ( is : 1786 ) . , providing and fixing steel gate, grating, and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide , plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : , a ) 20mm thick. , b ) 12mm thick , painting with synthetic enamel paint of approved brand and manufacture to give an even shade: two or more coats on new work , wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding : two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. , painting exterior surface of wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect including scaffolding and safety provision : new work. , supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. , providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section ( is 1038 1983 ) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 ( 1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size ) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooperglazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required : partly fixed and partly openable [ fixed area not to exceed 33% ] , supplying and fixing rolling shutters of approved make, made of 80 x 1.25mm. m.s. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 25.3cm. long wire springs grade no. 2 and m.s. top cover 1.25mm thick for rolling shutters as per design & is 6248 1979. ( clear openable area to be measured for payment ) . , steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m ) fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete : hot finished welded type tubes. , structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting ( height upto 10 m ) , fixing in position and applying a priming coat of approved steel primer all complete. , supply and installation of multi rib proofing / cladding sheet manufacture out of 0.60mm tct ( total coated thickness ) high tensile zinc aluminum alloy coated galvalume steel ( as per 150gsm zinc aluminum coated 550mpa tuekd strength ) confirming to is: 1397 / astm a 792 sheet to have wide pens 30mm high nb at 250 centre and centre width of 1020mm sheets be casted with regular modified polyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have proportionality with siphoned plate made to prevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. the sheet shall be supplied in cost one length and for a minimum up to 12mts with all scaffolding. , construction of shed ( jaggery production ) at rsgsm ltd kaminpura distt. sriganganagar , earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils , providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stoneaggregate 40mm nominal size ) . , brick masonry with f.p.s. bricks of class designation 75 infoundation and plinth with bricks cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) , providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix , centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. , providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor five level. ( original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to is:1786 ) thermo mechanically treated bars ( conforming of relevent is code ) , supplying and filling in plinth with blown sand under floors including watering ramming consolidating and dressing complete including cost of sand. , dry brick on edge flooring in required pattern with bricks of class designation 75 on a bed of 12 mm mud mortar including filling joints with river sandcomplete. , providing and laying m30 grade controlled cement concretepavements including mixing and vibrations concrete with necessary needle vibrators and surface with screed board vibrating complete in all respect with 20 / 25 mm stone aggregate ( crusher broken ) including anti skid textured finish to required camber / super elevation and grade including curing etc. as per specification with cement concrete m 30 grade including cost of steel frame work for sides of c.c. pavement consisting of m. s. channels flats and angles with required steel pegs ( some of them may left embedded in concrete / including providing frame work ) , structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting ( height upto 10 m ) , fixing in position and applying a priming coat of approved steel primer all complete: , supply and installation of multi rib proofing / cladding sheet manufacture out of0.50mm tct ( total coated thickness ) high tensile zinc aluminum alloy coated galvalume steel ( as per 150gsm zinc aluminum coated 550mpa tuekd strength ) confirming to is: 1397 / astm a 792 sheet to have wide pens 30mm high nb at 250 centre and centre width of 1020mm sheets be casted with regular modified polyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have proportionality with siphoned plate made to prevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. the sheet shall be supplied in cost one length and for a minimum up to 12mts with all scaffolding.add extra for 0.60mm tct ( total coated thickness ) high tensile zinc aluminum alloy coated galvalume steel sheet in place of 0.50mm thick 0.50mm thick , plaster on new surface on walls in cement sand mortar 1:4 including rackingofjointsetc. complete fine finish :20mm thick . , painting with synthetic enamel paint of approved brand and manufacture togive an even shade : two or more coats on new work , construction of rcc tank ( 17x 8 x 8 ) at rsgsm ltd kamanipura distt. sriganganagar , earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils , providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stoneaggregate 40mm nominal size ) . , providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix , centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. , providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor five level. ( original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to is:1786 ) thermo mechanically treated bars ( conforming of relevent is code ) , stone slab roofing on ground floor with fine grained stone slab from approved quarry including filling of joints of parapet and slab on both sides in cement sand mortar 1:4, with ceiling pointing in cement sand mortar 1 : 3 complete as per specification and instruction of engineer in charge , providing and laying brick kharanjaon roofs with cement mortar 1:4 ( 1 cement : 4 coarse sand ) mixed with 2% integral water proofing compound in square pattern 75mm to 100mm thick average , grading roof for water proofing treatment withwater proffing compoundcement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) ...

Rajasthan Cooperative Dairy Federation Limited - Rajasthan

34974235 various civil work and sheet replacement at cfp bikaner 1 demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meter lead as per direction on engineering in charge.in cement mortar 2 demolishing r.c.c. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50mtr. lead as per direction of engineering in charge. 3 dismantling doors, windows, clear storey windows steel or wood shutter icluding chowkhats and holdfasts etc. complete and stacking within 50 meters lead: of area exceeding 3 square meter. 4 demolishing cement concrete manually / by mechanical means including disposal of material within 50 meters lead as per direction of engineer in charge. 1:3:6 or richer mix. 5 dismantling roofing including ridges, hips, valleys and rafters etc. and stacking the within 50 meter lead of :asbestos sheet. 6 surface dressing of the ground including removing vegetation and inequalities not exceeding 15cm deep and disposal of rubbish lead upto 50mtr. and lift upto 1.5mtr. all kind of soil. 7 earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 mr. including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed within a lead of 50 meter. all kinds of soil. 8 providing and laying in position cement concrete including curing compaction etc. of specified grade excluding the cost of centering and shuttering all up to plinth level. 9 1:4:8 ( 1cement :4 course sand :8 graded stone aggregate 40 mm nominal size. 10 m20 grade nominal mix1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size ) 11 providing and laying in position specified grade of cement concrete cum for all rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement.m20 orade nominal mix / desion mix 12 providing and laying in position specified grade of cement concrete cum for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( i cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement for walls ( any thickness ) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix / design mix 13 providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( i cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15°, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix 14 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor five level.thermo mechanically treated bars ( conforming of relevent is code ) 15 centering and shuttering with plywood or steel sheets including sqm. strutting, propping bracing both ways and removal of formwork for foundation, footings, strap beam, raft, bases of columns etc. 16 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : 17 walls ( any thickness ) including attached pilasters. buttresses sqm plinth and string. 18 suspended floors. roofs, landings, staircases. balconies, girders, sqm cantilevers. bands, coping bed plates, anchor blocks.sills.chhaijas, lintel, beam. plinth beam etc. 19 columns, pillars, posts and struts etc. 20 add extra for shuttering in circular work ( in respective centering and sqm shuttering items ) 21 random rubble stone masonry with hard stone for foundation and plinth in cement sand mortar above 30cm thick wall in:cement mortar 1:4 ( 1 cement : 4 sand ) . 22 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level upto floor five level in all shapes and sizes in :cement mortar 1: 4 ( 1 cement : 4 coarse sand ) . 23 half brick masonry with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure, above plinth level upto floor five level .cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) 24 grading roof for water proofing treatment with water proffing compound cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stoneaggregate 20 mm nominal size ) 25 providing gola 75x75 mm in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge ) including finishing with cement mortar 1:3 ( 1 cement : 3 fine sand ) as per standard design : 26 providing and fixing up to floor five level pre cast cement concrete string or lacing courses, copings, bed plates, anchor blocks, windows sills, shelves, louvers steps, staircases, etc. including carriage, hoisting and setting in position with cementmortar 1:3 ( 1 cement: 3 coarse sand ) cost of requiredcentering, shuttering and finishing smooth with 6 mm thick cement plaster 1:3 ( 1 cement :3 fine sand on exposed surface, including all t & p, curing etc. complete: m15 grade nominal mix1: 2: 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) . 27 plaster on new surface on walls in cement sand mortar 1:4 including raking of joints etc. complete fine finish:. 28 25 mm thick. 29 20 mm thick. 30 12 mm thick. 31 6mm cement plaster to ceiling of mix 1:3 ( 1cement : 3 fine sand ) 32 making grooves as per design in plaster 10mm to 20mm wide. 33 providing & applying white cement based putty over plastered surface to prepare the surface even and smooth complete. 34 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect 35 structural steel work riveted. bolted or welded in built up sections. trusses and framed work. including cutting. hoisting ( height upto 10 m ) . fixing in position and applying a priming coat of approved steel primer all complete: 36 painting with enamel paint of approved brand and manufacture to give an even shade:two or more coats on new work. 37 steel work in built up tubular trusses including cutting. hoisting ( height upto 10 m ) fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete.hot finished seamless type tubes. 38 finishing walls with water proofing cement paint of required shade including all scaffolding. :new work ( two or more coats applied @, 3.84 kg / 10 sqm ) . 39 cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate ) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete.75mm thick with 20mm thick nominal size aggregate. 40 finishing with neat cement ( punning ) 41 random rubble dry stone kharanja 42 kota stone slab flooring 25 mm thick over 20 mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1: 4 ( 1 cement : 4 coarse sand ) for area of each slab from 2001 to 5000 sq.cm 43 kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average ) thick cement mortar 1:3 ( 1 cement 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and dolishing complete.for area of each slab from 2001 to 5000 sqcm 44 providing and fixing granite stone slab mirror polished and machine edge cut in walls. pillars. steps. shelves, sills counters.floors etc. laid on 12mm ( av. ) thick base of cement mortar 1:3 ( 1cement: 3 coarse sand ) jointing with white cement mortar 1:2 ( white cement: 2 marble dust ) with pigment to match the shade of the marble slab including grinding, rubbing and polishing comnlete.above 3601 cm slabs 45 providing and fixing external grade board solid core single / double leaf flush door shutters is: 2202 ( part il ) 1996 marked using phenol formal dehyderesin in glue both sides with approved stainless steel fittings complete as per annexure a30 mm thick.commercial veneer both side 46 providing and fixing t iron frames for doors, windows and ventilators of mild steel tee sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cmof 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) or with wooden plugs and screws or rawl plugsand screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 47 providing and fixing steel glazed doors, windows and ventilators shutters of standard rolled steel section joint mitred and welded with steel 13x3 mm lugs 10 cm. longembebbed in cement concrete blocks 15x10x10 cm. of1:3:6: ( 1 cement:3 coarse sand:6 graded stone aggregate 20mm nominal size ) or with wooden plugs and screws or rawl plugs and screwa or with fixing clips or with bolts and nuts as required, including providing and fixing of plan glass panes 4mm thick with copper glazing clips and special metal sash putty of approved make, or metal beading with screw complete including priming coat of approved steel primer, excluding the cost of metal beading and other fittingd except neccessary hinges of povits steel handles and peg stay etc. as required. is 1038 1983.partially fixed and partially openable fixed area not exceed 33% 48 providing & fixing fly proof wire gaugze to window, clearstory window & doors with m.s. flat 15x3 mm and nuts & bolts complete. stainless steel ( grade 304 ) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both side. 49 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 including jointing with seal ring conformining to is : 5382 leaving 10 mm gap for thermal expansion. ( i ) single socketed pipes.110mm type a 50 providing and fixing on wall face unplasticised pvc moulded fitting / accessories for unplasticised rigid pvc conforming to is : 13592 including jointing with seal ring conformining to is : 5382 leaving 10 mm gap for thermal expansion.110mmtype a 51 coupler 52 single bend with door 87.1 / 2 53 pipe clip 54 nahni trap 100x75 mm with cp jali 55 vent cowel 56 providing and laying factory made chamfered edge plastic coated designer cement concrete paver blocks of required strength, thickness & size / shape, made by table vibratory method, to attainsuperior smooth finish using pu or equivalent moulds, laid in required grey / yellow / red or any other colour & pattern over 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per manufacturers specifications & direction of engineer in charge:80 mm thick c.c. paver block of m 30 grade with approved color design and pattern. 57 p & f 1st quality vitrifiedtiles on floor, skirting and steps etc.in different sizes ( thickness to be specified by manufactuer ) with water absortion less than 0.08% and conforming to is 15622 of approved make in all colour and shade, laid with 20 mm thick cm 1 : 4 including grounting the joints with white cement and matching pigment etc complete.size 600 mm x 600 mm 58 providing and fixing 1st quality mat finished ceremic tile size 300x300mm confirming to is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete ( including the cost ofcementmortar bed 1:4 ) . 59 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to matchthe shade of the tile complete ( excluding the cost of cement plaster on walls and pillar ) . 60 extra for using greater size above 200x300mm in glazed tiles and for using 300mm x 450mm. 61 providing & fixing square bars of other flat welded to window, ventilator etc....

Medical And Health Services - Rajasthan

34206683 construction of shc bejpur block itawa distt. kota 1 clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 2 earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift upto 1.5 mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering and ramming and disposal of surplus excavated soil as directed within a lead of 50 mtr. all kinds of soil 3 filling in plinth with locally available river shingle under floors including watering ramming consolidating and dressing complete including cost of shingle sand. 4 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 5 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 6 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement.m20 grade nominal 7 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix 8 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for :columns, pillars, posts and struts etc. 9 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for :suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 10 random rubble stone masonry for foundation and plinth in cement sand mortar above 30 cm thick wall in :cement mortar 1 : 6 (1 cement : 6 sand). 11 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix 12 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. thermo mechanically treated bars (conforming of relevent is code) 13 filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead upto 50 mtr. and lift upto 1.5 mtr. 14 filling in plinth withlocally available good earth under floors including watering ramming consolidating and dressing complete including cost of locally available good earth 15 flyash flyash brick work with flyash flyash bricks of class designation 75 in superstructure above plinth level upto floor three level in all shapes and sizes in :cement mortar 1 : 6 (1 cement : 6 coarse sand) 16 half flyash brick masonry in superstructure , above plinth level upto floor three levelusing flyash bricks of designation 75 cement mortar 1 : 6 (1 cement : 6 coarse sand 17 random rubble dry stone kharanja under floor. 18 providing and fixing 15 to 20 mm thick granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12 mm (av.) thick base of cement mortar 1 : 3 (1 cement : 3 coarse sand) jointing with white cement mortar 1 : 2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of :green / black / other granite. above 3601 cm2 slabs 19 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 300mm x 450mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 20 providing and fixing 1st quality mat finished ceremic tile size 300 x 300 mm confirming to is : 13753 colour such as white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (untile of roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of the complete (including the cost of cement mortor bed1:4). category a : kajaria, jhonson, somani make 21 providing & fixing vitrified paving tiles size 600 mm × 600 mm × 12 mm thick fix with cement mortar over 20 mm thich (1 cement 4 sand) laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (untile or roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (including the cost of cement mortor 1:4) category a : kajaria, jhonson, somani make 22 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure a :30 mm thick commercial veneer both side 23 add extra in flush doors :for double leaf 24 for external teak wood lipping on flush door30mmx6mm 25 extra for cutting rebate in flush door shutters (total area of the shutter to be measured). 26 providing and fixing anodised aluminium curtain rod with aluminium brackets complete :25 mm dia 27 providing and fixing t iron frames for doors, windows and ventilators of mild steel tee sections, joints mitred and welded with 15 x 3 mm lugs, 10cm long embedded in cement concrete blocks 15 x 10 x 10 cm of 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 28 supply and fixing in cement mortar welded hand railing made out of ms round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or pvc hand railing to be paid extra) with priming coat of red oxide. 29 providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 30 providing and fixing m.s. sheet single leaf door shutter in angle iron frame 35 x 35 x 5 mm suitabilly diagonally braced with 25 x 3 mm flat iron above and below lock rail of size 50 x 5 mm beading extra including all fittings, as per direction of engg. incharge but excluding cost of chowkhats : including two coats of anit corrasite red oxide primer paint. m.s. sheet 18 s.w.g. 31 supplying and fixing of steel windows made out (65 x 40 mm) hollow metal pressed section of 1.25 mm thick sheet f4 & f7 standard rolled section conforming to is 1038 with wholly openable shutter of 0.80 mm thick (out side & inside) opening c.r. sheet embossed panels, joints matted and flush welded with suitable hinges, steel lugs & screws with approved oxidised steel handles, fittings, peg stays (casement stays) etc. complete in all respect including providing 10 mm square m.s. bars 10 cm. c/c and applying priming coat of red oxide paint. 32 supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20 x 3 mm with suitable screw at not exceeding 150 mm distance. 33 providing batta (gola) 75 mm x 75 mm in cement concrete (1 : 2 : 4) including finishing with cement mortar 1 : 3 as per standard design. 34 providing & laying chequerred plain cement concrete embossed to specially manufactured non slipping tiles of approved make 20 mm thick laid on 20 mm thick bed of cement mortar 1 : 6 jointed with neat cement slurry complete.medium shade using approximately 50% white cement and 50% ordinary cement. 35 plaster on new surface on walls in cement sand mortar 1 : 6 including racking of joint etc. complete fine finished :25 mm thick 36 plaster on new surface on walls in cement sand mortar 1 : 6 including racking of joint etc. complete fine finished :20 mm thick 37 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand). 38 applying priming coat :with ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. 39 painting with enamel paint of approved brand and manufacture to give an even shade :two or more coats on new work. 40 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including prepration of base and all scaffolding :new work (two or more coats) over and including scrapping and priming coat with cement primer. 41 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. new work 42 renewing glass panes, with putty and nails wherever necessary :4 mm thick plain glass panes. 43 supplying and fixing dressed sand or other approved stone shelves, tands in cement mortar 1 : 3 with fine dressed edges : 35 mm thick. 44 supplying and fixing in walls machine cut and polished stone shelves, tands andin cm 1:3 with machine cut edges :kota stone 25 to 30mm thick. 45 making of health wellness center patern (gola) including colour picture work in side for fascasde branding includig material labour and t & p as pe direction engineer in charge as per standared drawing/patern 46 making of border of window health wellness center as per given patern for fascasde branding includig material labour and t & p as pe direction engineer in charge up to window size 4x5.6 as per standared drawing/patern 47 extra for providing edge moulding to 15 18mm thick marble/ granite stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge.granite work / kota stonefull edge moulding 48 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completebirla/j.k./nerolac or iso. as per direction of engineer in charge. 49 providing& fixing precast cement concrete coping 1: 2:4mix50mmthickcompleteas per specification 50 finishing with 25 mm thick cement plaster on roofs in cement sand mortar 1 : 4 mix including water proofing compound @ 2% of cement used. with neat cement, finishing, curing etc. complete in all respect including making of 300 mm x 300 mm square. 51 providing and fixing indian type white glazed vitreous china 1st quality w.c. orissa pan (is : 2556 mark) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor. size 580 x 440 mm 52 p & f wvc wash basin (1st quality is : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p.pillar cock (is : 8934 mark) & 32 mm c.p. brass waste coupling of approved make, 25 mm g.i. waste pipe complete including cutting & making good the wall. size 510 mmx 400 mm 53 p & f wvc wash basin (1st quality is : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p.pillar cock (is : 8934 mark) & 32 mm c.p. brass waste coupling of approved make, 25 mm g.i. waste pipe complete including cutting & making good the wall. size 550 x 400 mm dia for counter top 54 p & f kitchen & lab sink of approved make with c.i. brackets duly painted, 40 mm c.p. waste coupling, c.p. brass chain with rubber plug, 40 mm g.i. waste pipe upto floor level complete including cutting & making good the wall & floor. 1.0 mm thick salem stainless steel aisi 304 kitchen sink of approved make (nirali, neel kanth, jaina, faber, criystal ) with large waste couplings is 13983 1994 over all size bowl size(inches) (inches)24 x 18 x 8 20 x 16 x 8 55 p & f looking mirror with pvc frame of approved (atul/ equivalent)size 500 x 400 mm 56 providing and fixing towel rail or ring of approved quality / make. c.p. brass towel rail with brackets 450 x 20 mm. 57 providing and fixing soap dish or tray of approved quality / make. c.p. brass 58 providing and fixing bath shower of approved quality / make. c.p. brass of heavy & superior quality 150 mm. 59 providing & fixing c.p. flange for 15 mm dia taps 60 p & f bib cock (is: 8931 mark) superior quality of approved make c.p. brass bib cock, 15 mm nominal bore 61 providing and fixing inlet connection (angle, valves) superior quality, of approved make.for wash basin gyser etc.c.p. inlet connection 15 mm.brass (is: 8931 marked) 62 providing and fixing 15 mm dia connection pipe of approved quality / make. pvc pipe with cp brass nuts upto length 600 mm 63 providing and fixing flush cock / flush valve (is : 9758 mark) for wc of approved quality make. c p brass half turn exposed 25 mm nominal bore 64 providing and fixing full way valve (is : 778 mark) or wheel valve of approved make. gun metal 15 mm nominal bore 65 providing and fixing full way valve (is : 778 mark) or wheel valve of approved make. gun metal 25 mm nominal bore 66 providing and fixing pvc storage tank confirming to is : (12701 marked indicating the bis license no) of approved make with cover, 25 mm dia 1 m long g.i. over flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc. complete of approved design.500 litres capacity 67 hoisting charges for each floor. 68 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work exposed on wall) 20mm nominal outer dia pipes 69 providing and fixing 3 layer pp r (polypropylene random coplymer ) pipes sdr 7.4 uv stabilized and antimicrobial fusion welded, having thermal stability for hot & cold water supply including all pp r plain & brass threaded polypropylene random fittings including trenching, refilling and testing of joint complete as per direction of engineer in charge. (external works)pn 16pipe, 32 mm od 70 providing and laying c.c. 1 : 5 :10 (stone aggregate 40 mm nominal size) upto haunches of s.w. pipes including 150 mm thick bed concrete as per rajasthan pwd specifications : (width w = dia of pipe in cm + 40 cm.) concrete width to be reduced from width w at centre of pipe to 0 at top of pipe.(excluding cost of pipe )100 mm dias.w. pipe 71 providing and fixing rigid pvc pipe (is : 4985 mark) class ii (4 kg./cm2) approved quality / makeincluding jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia 72 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia coupler (socket) 73 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia plain tee 74 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia bend 45° 75 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia bend 87.5° 76 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia vent cowel 77 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia pipe clip 78 construction of chamber in all types of soil with 300 mm thick masnory in cm. 1 : 6, 100 mm thick c.c. 1 : 5 : 10 in foundation , 20 mm thick inside plaster in cm 1 : 6, finished with floating neat cement 50 mm thick m 15 grade c.c. flooring earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. inside size 450 x 450 mm depth upto 0.5 m cement coverwith frame 79 construction of chamber in all types of soil with 300 mm thick masnory in cm. 1 : 6, 100 mm thick c.c. 1 : 5 : 10 in foundation , 20 mm thick inside plaster in cm 1 : 6, finished with floating neat cement 50 mm thick m 15 grade c.c. flooring earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. inside size 600 x 450 mm upto depth of 0.5 m cement cover with frame 80 construction of soakage well in all types of soil 300mm thick dry stone masonry, top and bottom 300 mm course in cm 1 : 6, 80 mm thick stone slab, jointing of slab in cm 1 : 3, ralthal, kharanja, 40 mm thick m 15 grade c.c. flooring earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr. size 240 cm dia outside & 240 cm depth 81 construction of septic tank in all types of soil with 40 cm. thick masonry in cm 1 : 6, 15 cm. thickc.c. bed of 1 : 5 : 10, m 15 grade c.c. flooring & over stone slab covering, 80 mm thick slab, jointing of slab in cm 1 : 3 ralthal, kharanja, 50 mm thick stone partition walls, 20 mm thick plaster in cm 1: 6 finished with neat floating cement, 4 nos c.i. foot rests of approved design, two no. 450 mm dia 25kg. of each c.i. cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr. size 200 x 100 x 130 cm (for 10 users) 82 construction of cement concrete chamber 125mm dia on depressed floor upto 45cm height from floor with : stainless steel sheet grating 83 wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p iii ) vergin material pvc conduit & its all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheets & electrical/ wiring accessories refer chapter e 04, e 05 & e 07 . for additional technical parameters of products/ work , refer annexure a attached with this bsr short point (up to 3 mtr.) 84 medium point (up to 6 mtr.) 85 long point(up to 10 mtr..) 86 wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p iii ) vergin material pvc conduit & its all accessories( j.b. , bends etc.) , round tiles, 18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, 3/ 5 pin 6 a modular socket, modular face plate with grid plate, screws etc,all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheets & electrical/ wiring accessories refer chapter e 04, e 05 & e 07. for additional technical parameters of products/ work refer annexure a attached with this bsr on board 87 medium point (up to 6 mtr.) 88 s&f following sizes (dia.) of isi marked mms ( is:9537 p iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 20 mm 89 25 mm 90 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure a attached with this bsr 2 x 2.5 sq. mm. + 1x1.5sqmm 91 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 92 supplying and fixing of power plug point with modularaccessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 18 swg with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of isi marked modular 16 amp. switch (is :3854) and 3/5 pin 16 amp. socket outlet (is:1293) [ as per detailed in respective item in bsr] , making connection , testing , etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 93 providing & fixing of modular type step fan regulator duly isi marked (is :11037) as per pwd specification for electrical works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip 20 rating , minimum width of 1 module switch toggle( push part ) should not less then 20mm, including all as per pre approved by engineer in charge,making connections, testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 5 step fan regulator 100 watt 2 module 94 providing & fixing of heavy duty capacitor start, copper woind double ball bearing 900/1400 rpm single phase exhaust fan as per pwd specification for electrical works, conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. oem shall be an iso certified company. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached withthis bsr .300 mm sweep(900/1400 rpm) 95 providing & fixing of ik07 ip 66 protected led street light luminaire on existing bracket/pole. fixture made of powder coated single piece pressure die cast aluminum lm6/ adc12 material with heat dissipation fins on housing with uv stabilized pc/toughened glass cover (uv stablzation report submitted for uv cover ) and secondary lens on each led & should be smd type . the system level luminaire efficacy >=120 lm/ wt with high power leds is to be used and potted driver must be potted & has a unique bis r number with input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety ,input frequency 50hz±3% power factor >0.95 driver efficiency >85% ,thd(i) <10% humidity 10% to 90% rh working temp 5c to 45c . driver current <1000ma shown in lm79 report. the luminaire shall be bis certified and t.c. certified. life expectancy equal or more than 50000 burning hrs with minimum 70% lumenmaintened,colorrendering index>70 andcct 5700k+355k. surge protection shall be min = 4 kv internal and min 10 kv external. driver should be phase to phase protection of 440 v for 4 hrs. manufactures word mark/name engraved/embossing on die cast housing to allow traceability/authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate/ report with liable warranty of product/accessories from oem shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr led street light fixture 70 watt 96 providing & fixing of 240/415 v ac mcb with positiveisolation of breaking capacity not less than 10 ka (b/ c tripping characteristic as per type of load and site requirement) 4kv impulse withstand voltage, as per pwd specification for electrical works with isi marked is 8828(1996) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 a rating and 10,000 upto 63 a, 5000 for 80 a rating including making connections, testing etc. as required. . oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with thisbsr .single pole mcb6 a to 32 a rating 97 double pole mcb50 63 a rating 98 providing & fixing of ik09 recessed/surface mountingheavy duty horizontal type sheet steel of 1.6 mm thick distribution board as per pwd specification for electrical works isi marked conforming to is 13032 & is 8623 / conforming to iec 61439 3. phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal db terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.oem shall have submit nabl / cpri/ erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr ip 43 double door (single phase)6 way (6 o/g +2 i/c ) 99 supply & laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with gi/cu thimble etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 8 swg copper wire 100 providing & fixing of ip40 led recessed / surface mounted, round / sqaure non dimmable back lit smd mid power led downlight with die cast aluminum housing & heat sink for heat dissipation with uv stabilized non yellowish diffuser with internal/ external bis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% and in compliance to iec standards. system lumen efficacy of = 120 lm / watt, thd < 10 % ,p.f.=0.95, cri >80, life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) ,maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsrrecessed mountingled downlight 18/20w 101 providing & fixing of ip40 led surface/ recessed / suspended mounting mid power smd type led light fixture made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 2.5 kv internal/external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection and in compliance to iec standards (integral with light fixture). system lumen efficacy of = 120 lm/watt ,thd < 10 % , p.f.=0.95,cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsrrecessed mounting36w led light fixture 2x2 with acrylic / prismatic front cover 102 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , power consumption of 18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k/ 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsr.4 led tube shape fixture 18/20 w (polycarbonate base) 103 sitc of chemical gel earthing system of dual pipe technology made of with b class g i pipe as per is 1239 ( part 1):2004 of medium duty of following sizes as per points mentioned (a), (b), [c), (d), (e) below : (a) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, cpri/ erda tested with rms capacity of minimum 35 40 ka for withstanding 1 second(b) to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated lab for low resistivity ( less than 0.12 ohm meter) & high conductivity in nature with carbon as a major content as per referance of is 3043 1987,ieee 80 2013 (clause 14.5d) , ieee 837 & ier 1956 with latest amendemnts©heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height 250 to 300 mm.(d) testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book.(e) self certificate for confirming above standards from oem is mandatory. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr .with pipe in pipe technology (outer pipe dia. / inner pipe dia. ) minimum 100 mm dia borewellgi pipe 2000 mm long, 80 / 50 mm, terminal 50mm x 6 mm gi strip 104 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un armoured / armoured aluminium cable of 1.1 kv grade as per pwd specification for electrical works in existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below: (a) material : h4 grade aluminium conductor of purity >99.6 %& as per is:1554 p i / is :7098 p i(b) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999 for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures .(c) oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities for cables . appropriate type test certificate / oem test report shall be submitted . all above as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . armoured cable10.0 sq. mm2.0 core 105 providing & fixing of iso certified company made bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan as per pwd specification for electrical works, conforming to is:374 2019, & is:1885 p v 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 1200 mm sweep bee 2 star rated (service value >=4.5 to < 5 ) 106 supply & fixing of abc type (map 50) type powder fire extinguisher (stored pressure type) of following capacity duly current and valid bis certification conforming to is: 15683:2006, with dry chemical powder used as extinguishing agent should be mono ammonium phosphate 50% concentration conforming to is 14609:1999. oem will produce supplier certificate complete with squeeze grip release valve, locking arrangement, pressure gauge and bracket including initial fill and wall suspension complete in all respect. serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. the firm should submit the product certificate from an en notified body & product performance test report from nabl accredited lab as per is 15683. . all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 4 kg 107 supply installationtesting&commissioningofisocertified manufacturer made monoblock motor pump set isi marked (is:9079 2002) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single/three phase ( 240 440 v ) permanent split capacitor type (psc), fitted with thermal overload protection, . including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. appropriate type test certificate / oem test report shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 0.5 hp, 1 ø, (3 18)mtr, (100 26) lpm 108 construction of tube well 100 metre depth and above in all type of rocks by dth system and over burden, to accommodate casing pipe of following size in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per is : 2800 (part i & ii) 1979 specifications. the work would be completed after obtaining sand free water. the tube well should have a throughout bore as per nominal dia of casing pipe. 200 mm dia nominal bore 109 development of tube well as per is specifications using suitable compressor to give sand free water for required yield of the gravel packed tube well. 110 supply of erw m.s. black casing pipe isi marked (is : 4270/1992) of grade fe 410 of following sizes at site of work. nominal bore of pipe200 (mm) 111 supply & fixing tube well cover of m.s. sheet (6 mm thick) with nuts and bolts complete for casing size. 200 mm dia 112 supply & fixing m.s. clamp, set of 50 x 6 mm flat from iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. 113 providing & fixing of single stage, water cooled, high speed(2880 rpm), horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t/c vs t/c, thrust bearing shall be of carbon + s.s.the stator body of single phase pump shall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition (ced) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 2.0 hp, 1 ø, (12 25) mtr, (350 115) lpm 114 supplying andlaying isimarkedp.v.c. insulated submersible cable as per pwd specification for electrical works confirming to is:694 and as per is 8130 : 2013 of 1.1 kv grade .wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4 including making connection etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. all as per pre approved by engineer in charge, making connections. for additional technical parameters of products/ work , refer annexure a attached with this bsr 6.0 sq.mm 3 core flat / round 115 providing & fixing of hdpe pipe isi mark (is:4984/2016 ) for watersupply (suitable for submersible & jet pump) with required fittings ie socket, elbows, tee etc. complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 50 mm od 6 kg / cm2 116 construction of 185 cm. dia platform as per approved design and drawing of unicef. 117 supply installation testing & commissioning of iso certified company made dol/star delta starter panel made out from 1.6 mm thick powder coated crca sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, illuminated on / off push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. appropriate type test certificate / oem test report shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr for single phase submersible / monoblockpump0.5 hp to 3.0 hp (dol starter) ...

Defence Research And Development Organisation - Rajasthan

34157131 repair to hardstanding, pcc paths and other misc works in mes installation at defence lab jodhpur 1.00 excavating in post holes or similar holes each not n exc 0.50 cu.m, getting out any type of soil, returning, fillig in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm complete all as specified and directed by engineer in charge. 2.00 m&l plain cement concrete ( 1:4:8 ) type d 2 using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified & directed by engineer in charge. 3.00 m&l plain cement concrete ( 1:2:4 ) type b 1 using 20 mm graded crushed stone aggregate as in kerbs, coping, bed plates, including weathering slightly rounded off, plinth courses, parapet walls etc complete all as specified & directed by engineer in charge. 4.00 dismantling posts or struts ( wood, steel or rcc ) any section, including taking out embedded portion from natural ground and making good disturbed ground complete all as specified and directed by engineer in charge. 5.00 dismantling posts or struts ( wood, steel or rcc ) any section, including taking out embedded portion from concrete, brick work, masonry, etc. and making good disturbed ground complete all as specified and directed by engineer in charge. 6.00 s&f mild steel sections like angle, flat etc in post and struts in fencing including cutting top to shape as directed, drilling holes, notching for wire etc;flat iron fillets ( for securing wire mesh etc including all necessary drilling, bolting or riviting etc confirming tofe 290gde e 165 complete all as specified & directed by engineer in charge. 7.00 dismantling fencing wire mesh, any type and size complete all as specified & directed by engineer in charge. 8.00 fixing only chain link fencing including line wires round or square, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified & directed by engineer in charge. 9.00 supply only chain link ms galvanised fencing, any size or type ( size as approved by age ( i ) ) complete all as specified and directed by engineer in charge. 10.00 supply only mild steel round or square bars, in available length fe 290 ( gde 165 ) for fixing of chain link fencing complete all as specified & directed by engineer in charge. 11.00 s&f mild steel screw bolts ( machine made ) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n. exc 10cm long and dia 5 to 10 mm complete all as specified & directed by engineer in charge. 12.00 m&l preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint ( ordinary tint ) over a coat of red oxide, zinc chrome primer complete all as specified & directed by engineer in charge. 13.00 m&l preparation of old painted surface of kerb stone / concrete, old steel surface surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint ( ordinary tint ) in two different colour pattern complete all as specified & directed by engineer in charge. 14.00 dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified & directed by engineer in charge. 15.00 s&f pre painted galvalume aluminium zinc coating gi based corrugated steel sheeting 0.50 mm thick any colour having tensile strength 550 mpa as in roof coverings / cladding to wall, fixed with self tapping screws etc complete all as specified & directed by engineer in charge. 16.00 s&f pre painted galvalume aluminium zinc coating gi based plain steel sheeting 0.50 mm thick any colour having tensile strength 550 mpa as in roof coverings / cladding to wall, fixed with self tapping screws etc complete all as specified & directed by engineer in charge. 17.00 dismantling stone slab, interlocking paver blocks & tiles of any description or thickness in floors, aprons etc laid dry or laid dry and pointed, stacking serviceable material and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by engineer in charge. 18.00 m&l 60 mm thick, m 35 grade, machine pressed precast concrete inter locking paver block with grey cement and pigment, confirming to is 15658 2006, shape & size as approved by engineer in charge, laid over and including 25mm thick sand cushioning complete all as specified & directed by engineer in charge. 19.00 laying only 60 mm thick, m 35 grade, machine pressed precast concrete inter locking paver block with grey cement and pigment, confirming to is 15658 2006, obtained from dismantling laid over and including 25mm thick sand cushioning complete all as specified & directed by engineer in charge. 20.00 m&l 60 mm thick, m 35 grade, rubber moulded, machine pressed precast concrete inter locking paver block using colour pigment, confirming to is 15658 2006, shape & size as approved by ge, laid over and including 25mm thick sand cushioning complete all as specified & directed by engineer in charge. 21.00 m&l precast cement concrete ( 1:2:4 ) type b 1 using 20mm graded crushed stone aggregate as in window or door cills, lintels, bressumers, steps, quoin blocks, string courses, copings, kneelers, apex stone, pier caps, columns , posts, boundary pillers, bed plates, pintle blocks, ancho rage blocks, boulders, corbels, brackets, etc with plain fair faces, including chamfers, weatherings, kerb stone , throat ing etc.and setting in cement mortar 1:4 complete all as specified & directed by engineer in charge. 22.00 demolition of cement concrete unreinforced in ground floors, kota stone, granite flooring, tiles flooring and pavings not exceeding 15cm thickness ( below or above ground level ) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by engineer in charge. 23.00 m&l plain cement concrete ( 1:2:4 ) type b 1using 20mm graded crushed stone aggregate as in kerbs or benching complete all as specified & directed by engineer in charge. 24.00 m&l coloured chequered cement concrete tiles 25cmx25cmx20 25 mm thick, with grey cement and pigments, set, jointed with neat cement slurry and pointed with white cement and pigment to match the colour of tiles as in floors / path etc over and including screed bed or bedding layer of 20mm thick in cm ( 1:4 ) complete all as specified & directed by engineer in charge. 25.00 m&l rubble moulded chequered cement concrete tiles 30cmx30cmx20 25 mm thick, using colour pigment, set, jointed with neat cement slurry and pointed with white cement and pigment to match over and including screed bed or bedding layer of 20mm thick in cm ( 1:4 ) complete all as specified & directed by engineer in charge. 26.00 m&l 75 mm thick cement concrete ( 1:2:4 ) type b 1 using 20 mm graded crushed stone aggregate as in flooring / hard standing path in alternate bays area not exceeding 2 sqm each panel & joints filled with bitumen mastic ( 1:3 ) i.e.one part of bitumen and 3 parts of sand, and concrete surface even & smooth without using extra cement complete all as specified & directed by engineer in charge. 27.00 s&f for pre cast plain cement concrete ( type b0 pcc 1:1.5:3 ) using 12.5mm graded aggregate kangaroo ( as approved by engr in charge ) incl necessary excavation and return filling incl fixing with cement mortar ( 1:4 ) complete all as specified & directed by engineer in charge. 28.00 taking down cement or cement lime plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed by engineer in charge. 29.00 m&l plastering 15mm thick on fair faces of brick work / stone masonary or concrete surfaces in cement mortar ( 1:6 ) and finished even and smooth with using extra cement complete all as specified and directed by engineer in charge. 30.00 m&l preparing new plastered surfaces of walls and applying two coats cement based paint over a coat of primer complete all as specified & directed by engineer in charge....

Military Engineer Services - Rajasthan

34082114 addl / altn of mt shed ( p / 64 ) at rms dholpur taking down cenment plaster of any description including racking out joints, hacking for kay scrubing down with water etc all as directed. 2 taking down shutter exceeding 1 sqm and n.exc 2 sqm each complete all as specified & directed. 3 demolition of cement concrete ( unreinforced ) in ground floors and pavings n exc 15 cm thickness ( below or above ground level ) and removing unserviceable material exc 100 mtr as specified. 4 dismantling, floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing serviceable tiles to store and rubbish off the premises 5 factory made solid panel pvc door / cup board shutter 30mm thick ( style ) consisting of frame made out of m.s tubes for top & bottom rails.m.s frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour pvc sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail.panelling of plain colour pvc sheet to be fitted in the m.s frame welded / sealed to the stiles and rails with suitable pvc sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification in ssr part i. 6 s&f butt hinges medium grade cold rolled 100 mm mild steel and fixed 7 s&fmild steel barrel tower bolts 150 mm long, stove enamelled black with bright bolt. 8 s&fmild steel pressed handles oval type size 125 mm, stove enamelled black of all as specified. 9 s&f mild steel sliding door bolt 250 mm long, plate type stove enamelled black, with bright bolt not less than 12 mm dia with the incl a min of 6 bolts and nuts four on bolt plate and two on staple plate all as specified. 10 m&l glazed ceramiccoloured tiles 300 x 450 mm x7mm thick on skirting, dado set and jointed in neat cement slurry and pointed in white cement with pigment to match the surface over 10 mm thick screed in cm 1:4 all as specified. 11 m&l non skid ceramic coloured tiles 7 to 8mm thick ( square / rectangulament ) area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm, infloors set and jointed in neat cement slurry and pointed in white / colouredcement with pigment to match all as specified. 12 m&l 15 mm thick for screed bed or bedding layer of cm 1:4 for laying floor finishes. 13 s&f as in repair vitreous china squatting pan ( orissa pattern ) water closet ( white ) size 580mmx440mm with integral foot rests ( excluding flushing cistern and flush pipe ) complete including connection to trap and flushing pipe antisyphonage pipe etcincluding provision of pcc ( 1:7:12 ) type f2 in filling complete all as specified 14 s&f in repair pvc low level flushing cistern 10 ltrs capacity white with inlet ball value, float valve and handle incl brackets, pvc flush pipecomplete. 15 s&f in repair vitreous china wash basin white, ovel type of size 550x400mm including32mm dia pvc waste pipecp brass wast coupling 32 mmdia , pair of ms angle brackets or ms fastener / bolts for fixing arrangements / granite counter, 450mm long pvc connection with pvc nut and washercompleteat site and all as directed by engr in charge. 16 s & f in repair vitereous china urinal , half stall type white with grating and union for discharge pipe ( excluding flushing cistern flush pipe and waste pipe ) 17 s&f waste pipe 32 mm dia 550mm long pvc for urinal all as specified & directed. 18 s&f pvc connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore. 19 s&f in repair bib tap cast copper alloy with crutch or butterfly handle, chromium plated fency type screwedfor iron pipe, suitable for 15 mm bore complete all as specified. 20 s&f in repair angle valve cast copper chromium plated screwed down, high pressure with capstan head suitable for 15 mm bore, screwed both ends for iron pipe complete all as specified. 21 s&f in repair pillar taps, cast copper alloy, with capstan heads, chromium plated fancy type ( swan neck ) , screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by engr in charge 22 s&f in repair stainless steel gratings of outer frame dia 150 mm openable type incl all necessary fittings such as hinges including embeding in tiles with white cement. 23 s & f in repair 600 mm x 450 mm bevelled edge mirror or selected quality glass mounted on 6 mm thick ac building boards or commercial plywood and fixed to wooden plugs with chromium plated brass screwed and cup washers. 24 s&fin repair soap dish holder ( ss ) , any type, fixed toplugs withscrews all as specified and directed by engr in charge. 25 takind down gi tubingof 15 mm dia and connection and incl cleaning for refixing or removel all as spfd. 26 s&f 15 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors. 27 dismantling / disconnecting / demolition of water storage tank of any type or description and removing from site or refixing in position. 28 s & f rotational moulded polythylene water storage tank with 20mm ptmt with epoxy coated al rod float valve, plastic lid cover, tripled layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500 ltrs incl making connections complete all as specified. 29 s&f in repair 20 mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. 30 cutting chases for concealed water tubing or concealed conduit & making goodin cm 1.3 of girth exe 10 cm in stone, concrete block or slab wall etc all as specifed and directed by engineer in charge . 31 s&f pvc swr bends of 110 mm bore provided with access door 32 s&f pvc ( swr ) floor trap plain including jointing with solvent cement 75 mm dia all as specified 33 s&f pvc ( swr ) wc connector with lip ring 110 mm all as spfd. 34 m & l preparation of newly plastered surfaces and applying three coats of white wash in ceiling. 35 m&l for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide on new surfaces of steel or iron. 36 m&l for rendering 15 mm thick on stone masonary surfaces or surfaces other than fair face ofbrick work or on one side of lathing in cement mortar 1:6, finished even and smooth without using extra cement. 37 m&l for rendering 15mm thick in cement mortar 1:4 on stone masonrysurfaces or surface other than fair face of brick work of walls, finished even and sommoth without using extra cement on edges / chajjas / roof projection and simlar courses etc. 38 m&l rendering 5mm thick in cement mortar 1:3 finished even and smooth without using extra cement on ceilling surfaces complete all as specified. 39 m & l preparation of newly plastered surfaces and applying three coats of white wash in ceiling. 40 m&l for three coats of white wash on new plastered or unplastered surfaces of walls including prepration of surfaces. 41 m&l for 2 coats of cement base painting on newly plastered surfaces of wall incl preparation of surfaces all as specified and directed. 42 cutting openings through walls of cement mortar for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises 43 excavation in trenches in soft soil n. exc 1.5m width and 1.5m in depth and getting out all as specified. 44 returning filling including spreading levelling, watering and well ramming in layers n. exc 25cm all as specified. 45 removal of excavated soil to a distance n. exc 50m and deposited where directed n. exc 1.5m above the starting point. 46 brick work with sub class b bricks, straight or curved on plan exc 6m mean radius, built in cm 1:4 47 surface dressingn exc 15 cm deep in soft / loose soil all as specified. 48 m&l pcc 1:4:8 type d2 using 40mm graded aggregate 75mm thick in sub base, floors and paving all as specified. 49 m&l 40 mm thick pcc 1:2:4 type b2 using 20mm graded aggregate finished even and smooth as in floor complete all as specified. 50 framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding, with and including either hooks, and hinges or steel hanging, door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and, hanging; also fastening and, fixing complete all as specified and directed by engr in charge 51 m&l mild steel, plain, black sheet 1.00mm thickin hearths; covering to door shut ters; covering to door chowkats ( frames ) ; chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded / riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as require 52 dismantling of asbestos cement ( corrugated, semi corrugated etc, ) sheets in roof coverings etc complete all as specified and directed. 53 excavating in post holes in hard / dense soil n.exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers, n.exc 25cm and making good surface in soft / disintegrated soil 54 m & l for pcc 1:3:6 type c2 using 40mm graded stone aggregate as in foundation 55 m&l joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc of fe 290 ( gde e 165 ) ( cut to ordinary lengths i.e. within 20mm of the length indicated ) all as specified and directed. 56 supply and fixing mild steel rolled sections such as angles etc. as in main and cross beam, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding dorrs, fixed with angle cleats or other connected plates confirming to grad fe 290 ( gde e 165 ) complete all as specified 57 m&l for plain cement concrete type b1 1:2:4 ( 20 mm graded aggregate ) as in lintels upto 1.5 m clear sp and other similar bands, plinth courses, string courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones bed plates, water troughs and the like including weathering, slightly rounded or chamfered anglesand throating, as directed. 58 s&f pre painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, molding / folding in circular / semicircular of any position and height fixed with self tapping screws as specified, as directed by engr in charge...

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

33554650 civil work at ggups sanskrit punras block tarangar civil work at ggups sanskrit punras block tarangar 1.02 earth work in excavation by mechanical means (hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5 m , disposed earth to be levelled and neatly dressed:all kinds of soil 1.03 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 1.04 brick masonry with f.p.s. bricks of class designation 75 in foundation and plinth with bricks cement mortar 1 : 6 (1 cement : 6 coarse sand) 1.05 providing & laying chequered terrazzo tiles of approved make 22mm thick with marble chips of size upto 6mm, in floors, jointed with neat cement slurry mixed wit pigment to match the shade of tiles including rubbing and polishing complete in all respect as per specification, on 28mm thick bed of c.m. 1:4 :dark shade using ordinary cement. 1.06 providing and laying in position specified grade of cement concrete for all rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( as required) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix providing m 25 grade concrete by using min 410 kg of cement per cum instead of m 20 grade design mix. 1.07 centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. walls (any thickness) including attached pilasters, buttresses plinth and string course. 1.08 centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. 1.09 providing and laying in position specified grade of cement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( as required) excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix (slab & lintel) 1.10 brick work with clay flyash f.p.s. brick (is 13757 1993 ) of class designation 75 in superstructure above plinth level upto floor five level in : cement mortar 1 : 6 (1 cement : 6 coarse sand) 1.11 stone kharanja: random rubble dry stone kharanja under floor 1.12 half brick masnory with clay flyash f.p.s. brick (is 13757 1993 ) of class designation 75 in superstructure above plinth level upto floor five level in : cement mortar 1 : 4 (1 cement : 4 coarse sand) 1.13 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. thermo mechanically treated bars (conforming of relevent is code) 1.14 structural steel work in single section fixed with or without connecting plate including cutting, hoisting ( height upto 10 m), fixing in position and applying a priming coat of approved steel primer all complete. 40×40×5mm 3kg per rmt 1.15 providing and fixing m.s. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of engg. incharge but excluding cost of chowkhats: including two coats of anit corrosive red oxide primer paint extra for double leaf shutters. 1.16 providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (is 1038 1983) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required :partly fixed and partly openable [ fixed area not to exceed 33%] 1.17 supplying and fixing fixed wire gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150 mm distance.14 mesh x 24 gauge 1.18 guard bars:providing and fixing square bars or other flat welded to window, ventilatiors etc. 1.19 providing and laying ceramic mat floor tiles (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown of any size, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing in white cement mixed with pigment of matching shade complete. 1.20 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 1.21 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 12mm thick. 1.22 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. 1.23 plaster(ceiling): 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3 fine sand) 1.24 painting exterior surface of wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect.new work 1.25 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work 1.26 m15 grade nominal mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40mm nominal size). 2.00 part b sanetary work 2.01 provinding and fixing 3 layer pp r (polyproylene random copolymer) pipes sdr 7.4 uv stabilized & antimicrobial fusion welded, having thermal stability for hot and cold water supply including all pp r plain and brass threaded polypropylene random fittings and fixing the pipe with clamps at 1.00 spacing. this includes testing of joint complete as per direction of engineer incharge.(internal work exposed on wall)pn 16 pipe, 25 mm od 2.02 provinding and fixing 3 layer pp r (polyproylene random copolymer) pipes sdr 7.4 uv stabilized & antimicrobial fusion welded, having thermal stability for hot and cold water supply including all pp r plain and brass threaded polypropylene random fittings and fixing the pipe with clamps at 1.00 spacing. this includes testing of joint complete as per direction of engineer incharge.(internal work exposed on wall)pn 16 pipe, 16 mm od 2.03 p & f squatting pan ( indian type ) white glaze viterous china 1st quality w.c. pan ( is: 2556 mark) with 100 mm viterous china p or s trap including cutting & making good the wall & loor (excluding a pair of foot rest ) size 510 mm 2.04 p & f wvc wash basin (1st quality, i.s. : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p. pillar cock (is : 8934 mark) & 32 mm c.p. brass waste coupling of approved make,25 mm g.i. waste pipe complete including cutting & making good the wall.: 450 x 300 mm 2.05 p & f bib cock (is : 8931 mark) superior quality of approved make.c.p. brass 400 gm, 15 mm nominal bore. 2.06 p&f rigid pvc pipe (is:4985 mark) class ii/ (4 kg. /cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia 2.07 p& f waste coulping with fittings of approved quality /make:c.p. brass 40 mm dia 2.08 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: bend 87.5 110mm dia 2.09 pipe clip 110 mm dia 2.10 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant plain floor trap 110 mm dia 2.11 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant p trap 110 mm dia 2.12 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant vent cowel 110 mm dia 2.13 p & f wvc ( is :2556 mark) squatting urinal of standard make complete including cutting & making good the floor size 450 x 350mm 2.14 s/f rcc main hole covers with frame of approved make (light duty) size 450x450 mm 2.15 p/f grating of approved quality stainiese steet sheet size 125 mm dia 2.16 construction of soakage well in all types of soil of approved drawing , top 90 cm portion in 450 mm thick with cement mortar 1:6 80 mm stone slab covering jointing of slab in cm 1 : 3, ralthal, kharanja, 40 mm thick m 15 grade c.c. flooring earthwork etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr.inner dia 90 cm & 10 to 12 m deep 2.17 construction of chamber in all types of soil with 300 mm thick masnory in cm. 1 : 6, 100 mm thick c.c. 1 : 5 : 10 in foundation , 20 mm thick inside plaster in cm 1 : 6, finished with floating neat cement 50 mm thick m 15 grade c.c. flooring earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr.inside size 300 x 300 mm depth upto 0.5 m & 5 kg ci cover with frame. 2.18 p & f 15 mm dia connection pipe of approved quality make pvc pipes with nuts 450 mm. 2.19 p & f full way valve (is : 778 mark) or wheel valve of approved make. gun metal 15 mm nominal bore. 2.20 p & f stop cock (is:8931 mark),superior quality and of approved mark: brass 400 gm. 15 mm nominal bore 2.21 p&f gi pipes (external work) with gi fittings excluding union (si: 1239 mark) including trenching and refilling each etc. 15 mm dia nominal bore b class 2.22 p & f pvc storage tank isi marked ( is : 12701) indicating the bis license no. of approved make with cover , 25mm dia 1 m long g.i. overflow pipe & 25 cm long wash out pipe with plug & socket including making connection etc. complete of approved design 500 litres capacity ...

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

33524957 remaining work at gsss salari ( art and craft room ) block kekri district ajmer civil work 2 earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.all kind of soil 3 providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8(1 cement:4 coarse sand :8 graded stone aggregate 40 mm nominal size). 4 random rubble stone masonry for foundation and plinth in cement sand mortar above 30 cm thick wall in cement mortat 1:6 (1 cement: 6 sand) 5 centering & shuttering with plywood or steel sheets including strutting propping, bracing both ways and removal of formworksfor foundation in basements rafts , footings , straps beams , base of coloumns etc upto plinth level. 6 providing and laying in position specified grade of cement concrete for all rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement . m20 grade nominal mix (with graded stone agg. 20mm nominal size 7 filling available excavated earth (excluding rock)in trenches, plinth side of foundation etc. in layers not exceeding 20cm in depth consolidating each depositedby watering ramming inc. lead upto 50 mtr and with all lift supply and stacking good earth at site complete inc. loading unloading and transportation etc 8 random rubble dry stone kharanja under floor . 9 brickmasonaryinfoundation and plinth withbricks of class designation75 incement mortar 1:6(1 cement : 6 corase sand) add extra item no. 5.1 for brick work in super structure upto third storey.add extra over respective items all types of bricks for using clay fly ash bricks 10 centering & shuttering with plywood or steel sheets including strutting propping, bracing both ways with wooden members and removal of formworks upto floor three levelfor suspended floors, roofs, landing staircase balconies, girders, cantivlevers bands & bed plates anchor blocks sill, chajjas, lintel beams etc. 11 centering & shuttering with plywood or steel sheets including strutting propping, bracing both ways with wooden members and removal of formworks upto floor three level columns pillars posts and struts etc. 12 providing and laying in position specified grade of cement concerete for rcc structural elements upto floor three level inclu. curing, compaction, finishing with rendering in cement sand mortar 1:3 making good and joints exclu, cost of centering, shuttering and reinforcement for walls (any thickness) including attached pilasters butteresses plinth and string courses fillets columns pillars piers abutmnets post and struts (m20 gradenominal mix) 13 providing and laying in position specified grade of cement concerete for rcc structural elements upto floor three level inclu. curing, compaction, finishing with rendering in cement sand mortar 1:3 making good and joints exclu, cost of centering, shuttering and reinforcement (m20 grade nominal mix beams suspended floors roofs girders having slopes upto 15 degree landing balconies shelves chajja lintel bands plain window sill staircases and spiralstaircases 14 p/f reinforcement using steel of sail/vizak rinl /tata tiscon /essar/ zindal vijaynagar is:1786 1989 for rcc work inc. straightening cutting bending placing inposition and binding (inc. cost of binding wire ) all complete upto floor three level. thermo mechanicaly trated bars ( conforming of relevent is code) 15 plaster(internal)plaster on new surface on wall in cement sand mortar 1:6 including ranking of joints etc. complete fine finished 12 mm thick. 16 plaster(external)plaster on new surface on wall in cement sand mortar 1:6 including ranking of joints etc. complete fine finished 20 mm thick 17 plaster(ceiling)plaster on new surface on wall in cement sand mortar 1:3 including ranking of joints etc. complete fine finished 6 mm thick. 18 polished blue kota stoneflooring skerting,laid over20 mm thick base of cement mortar 1:4 and jointed with grey cement slurry to match of the shade of the slab including rubbing and polishing complete for area of each slab upto 900 sq.cm.25mm thick. deduct for using kota stone other than blue in colour 19 polished blue kota stoneflooring skerting,laid over20 mm thick base of cement mortar 1:4 and jointed with grey cement slurry to match of the shade of the slab including rubbing and polishing complete for area of each slab from 2001 to 5000sq.cm.25mm thick slab.deduct for kota stone other than blue colour 20 s&f in walls machine cut &polished stone shelves ,tands and sills in cm1:3 with machine cut edge kota stone 25mm to 30 mm thick. 21 polished blue kota stone slab in steps, walls, pillars having fine machine cut edges laid on 12mm (av) thickcement mortar 1:3 and jointed with grey cement slurry mixed with pigment to match of the shade of the slab including rubbing and polishing complete for area of each slab from 2001 to 5000sq.cm.30 mm thick slab.stair 22 providing and fixing ms sheet single leaf doors shutter in angle iron frame 35x35x5mm suitabilly digonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of engineer incharge but excluding cost of chowkhats including two coates of anti corrastie red oxide primer pant m.s. sheet 22 s.w.g. add 20 % extra for double leaf shutter. 23 providing and fixing t iron / angle iron frame for door and windows and ventilators or mild steel tee or angle section joined mitered and welded with 15 x 3 mm lugs, 10cm . long embedded in cement concrete blocks, 15 x 15 x 10 mm size of 1:3:6 (1 cement, 3 coursed sand and 6 graded stone aggregate 20 mm nominal size or with wooden plugs and screws or rawl plugs and screw or with fixing clips or with bolt and nuts as requesting including fixing of necessary butt hinges and screw and applying a priming coat of approved steel primer 24 providing and fixing steel glazed doors windows and ventilator shutters of standarad rolled steel section joints mitred and welded with lugs 13x3mm,10cm long embeded in cement concrete block 15x10x10cm of 1:3:6 or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with coper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approved steel primer, excluding the cost of metal beading and other fittings expect necessary hings of pivots steel handles peg stay etc.as required partly fixed and partly openable.(fixed area not to exeed 33%) 25 supplying & fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 26 providing and fixing square bars or other flat welded to window ventilators etc 27 panting on doors & windowspainting with ready mix paint of approved brand and manufacture in all shade to give an even shadenew steel work (2 or more coat ). 28 applying birla/jk cement based putty over cement plaster surface for making even surface 29 applying exterior emulsion paint like ace, apex or equivelent brand and manufacture of required shade to give an even shade inc. all scaffolding on prepared surface new work two or more coat 30 distempering with oil bound washable distemper of appd. brand and manufacture to give an even shade inc. all scaffolding new work (2 more caot) over and inc. scrapping and priming coat with cement primer. 31 grading for roof water proofing tratment with cement concreate 1:2:4 (1cement :2coarse sand :4 graded stone sggregate 20mm nominal size) with water proof compound as per manfacuture specification 32 providing batta (gola) 75 mm x 75 mm in cement concrete (1:2:4) including finishing with cement mortar 1:3 as per standard design. 33 p& f rigid pvc pipe (is 4985 mark) class 2nd /(4 kg /sqcm) approved quality / make including joining the pipe with solvant cement rubber ring and lubricant 110 mm dia. 34 s/f rough dressed stone sills, dasa, coping, cornices, sriwan, string courses in cement mortar 1:4 including pointing with admixture of pigment matching with the stone shade 50mm thick 35 electric work 36 s & f follwing sizes (dia.) of isi marked medium duty pvc conduit along with accessories in surface/ recessed using saddles, clamps, fastener as required including cutting the wall covering conduit and making good the same as required. group 1 (25 mm dia) 37 p & f 18 swg m.s. recessed fan box, hexagonal/round of size 130mm dia, depth 75mm length, 12mm dia rod fan hook with 100 mm length extended on each side. group 1 38 wiring of light point/ fan point/exhaust fan point/ call bell point with 1.5 sq. mmnominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv grade and 1.5 sq. mm fr pvcinsulated unsheathed flexible copper earth conductor 1.1 kv grade (is: 694) of approved make in surface / recessed isi marked mms(is:9537 p 111) pvc conduit and its accessories , round tiles ,18 swg ms box with earth terminal, 6a switch, 3.0mm thick isi marked phenolic laminated sheet, zink plated /brass screws cup washer making connection testing etc. as required group 1 short point (up to 3 mtr.) 39 medium point (up to 6 mtr) 40 long point (up to 10 mtr) 41 wiring of 3 pin 5 amp. light plug point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade and 1.5 sq. mm nominal size fr pvcinsulated unsheathed flexible copper earth conductor 1.1 kv grade (is: 694) of approved make in surface/recessed isi marked mms (is:9537 p iii ) pvc conduit & its accessories 18swg 175mm x100 mm x 60 mm m.s box with earth terminal 6 a phenolic laminated sheet making cnnection testing etc. as requiredgroup 1 on board 42 supplying and drawi;ng fr pvc insulated & unsheathed flexible copper conductor isi marked (is:694) of 1.1 kv grade and approved make in existing surface ofr necessed conduit/ casting capping including making connections etc. as required. group 1 2x2.5sqmm+1x1.5sqmm 43 p & f 240/415 v ac mcb of with positive isolation of breaking capacity not less than 10 k.a (b/c/d tripping characterstic) isi marked is 8828(1996)/conforming to iec 60898 in existing board/sheets including making conections testing etc. as required. group 16 a to 32 a rating 44 p & f recessed/ surface mounting heavy duty horizontal type sheet steel distribution board phophatised/ powder painted complete with suitable rating insulated coppers bus bars shorting link neutral link,earth link, and din bars masking sheet conforming to isi2032 & is8623 including making internal db terminators with copper lugs testing etc. as requireddouble door single phase 4 way group 3 45 p & f strip fluorscent tube fitting fabricated from (crca sheet and finished with powder coating/stove enamelled paint)/( extruded non corrosive uv resist ep channel)complete with accessories(low loss copperchoke, starter, starter seat)/electronic choke with terminal block duely prewired with copper conducter including making connection, testing etc. as required(without tube) 1x36watts with eb gr. 1 46 p & f fluorscent tube rod in existing fixtures as required, ,36/40 watts group 1 47 p & f star rated double ball beari;ng capacitor start, aluminium bodyand blade ceiling fan with down rod upto 30 cm with 3x1.5 sqmm pvc insulated flexible copper conductor making connection testing etc as required. 1200mm sweep 5star rated group 1 48 p&f socketrsize flush type 120/280 watt rotary 5 step fan regulator including making conenction testing etc. as required 49 p & f 18 swg sheet steel boxes duly finisded with two coats of red oxide and with earthing terminal of following sizes (nominal size) on surfacae or in recessed as required. 175mmx 100mmx60mm 50 p/f pvc sheet of size 75mm dia inc. screw cup washer as required 51 p/laying p.v.c sheathed cable of 1.1 kv grade with aluminium conductor fo is:1554 p 1/is:7098 p 1 fo approved make in ground as per is:1255 including excavation fo 30cmx75cm size trench 25 cm thick under layer of sand iind class bricks covering refilling earth compaction of earth making necessary connection testing etc. as required of size 4.0 sq mm, 2 core ...

Military Engineer Services - Rajasthan

33421946 provn of clothing and medical store at army area under ge shikargarh jodhpur excavation in trenches n.exc 1.5 m wide & n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in soft / loose soil complete all as specified and as directed. 2 m&l pcc 1:4:8 type d2 ( 40 mm graded aggregate ) in foundation filling and mass concreteetc complete etc.all as specified and as directed. 3 m&l for brick work with fly ash bricks ( old size bricks ) , straight or curved on plan exc 6mtr mean radius, built in cement mortar ( 1:6 ) complete all as specified and as directed. 4 m&l for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides of soffits ( if any ) of foundations and plinth beams and similar work etc; rough finish surfaces complete all as specified and as directed. 5 m&l for form work to sides of concrete pillars, posts, struts, piers, columns and stanchion etc; rough finish surfaces complete all as specified and as directed. 6 m&l for form work to sides and soffits of floor or roofrcc beam sides of lintel beam flat rough finish surfaces to receive the plaster, complete all as specified and as directed. 7 m&l for formwork for chullah hoods, chajjas through and similar items including edges, surface rough finish surfaces to receive the plaster, complete all as specified and as directed. 8 m&l for form work to soffits of suspended slabs such as roof slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) , rough finish surfaces complete all as specified and as directed. 9 m&l for form work to edges of concrete flats, floor and roofs not exceeding 20cm wide ( horizontal or sloping ) , rough finish surfaces complete all as specified and as directed. 10 m&l for providing rcc 1:1 1 / 2:3 type b1 ( using 20mm graded stone aggregate ) as in foundations, including raft footings, foundations beams, plinth beams, bases of columns etc; complete all as specified and as directed. 11 m&l for providing rcc 1:1 1 / 2:3 type b1 ( using 20mm graded stone aggregate ) as in columns, pillars, piers, posts and struts etc; complete all as specified and as directed. 12 m&l for providing rcc 1:1 1 / 2:3 type b1 ( using 20mm graded stone aggregate ) as in beams, lintel up to 1.5m clear span, lintel bands etc; complete all as specified and as directed. 13 m&l for providing rcc 1:1 1 / 2:3 type b1 ( using 20mm graded stone aggregate ) as in slabs supported on walls, beams and columns in roof, landings, balconies, canopies and in shelves etc; complete all as specified and as directed. 14 m&l for providing rcc 1:1 1 / 2:3 type b1 ( using 20mm graded stone aggregate ) as in chajjas etc; complete all as specified and as directed. 15 m&l for reinforcement 10mm dia and over tmt bars cut to length, bent to shape required and binding with ms wire not less than 0.9mm dia or securing with clips complete all as specified and as directed. 16 m&l for reinforcement 8 to 10mm dia tmt bars cut to length, bent to shape required and binding with ms wire not less than 0.9mm dia in stirrupscomplete all as specified and as directed. 17 m&l for carrying out water proofing treatment forroofs in the following stages ( i ) rendering 10mm thick in 1:4 mixed with integral water proofing liquid all as per manufacturers instructions over concrete surfaces finished even and smooth with out using extra cement. ( ii ) first coat of bitumen primer confirming to is 3384 @0.300 kg / sqm over plastered surafces ( iii ) secondlayer of 3.0 mm thick app modified polymeric membrane with centre core of single non woven polyster reinforcementandhaving weight 3 kg / sqm with mineral gravel finish on top complete laid with blown type bitumen grade 85 / 25 @ 1.20 kg / sqm complete all as specified and as directed. ( iv ) finally applying two protective coats of bituminous aluminium based reflective paint to safeguard against uv, including preparing of old surfaces of roof remove all corrosion products brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots incl washing , rubbing down and stopping of painted surfaces ( second coat apply after 24 hrs or as per manufacturing instructions ) . 18 supply only integral water proofing liquid isi marked make: pidiproof lw 19 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm each layer in hard / dense soil all as specified and directed. 20 removing excavated soil n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point all as specified and directed. 21 m&l for 15 mm thick rendering on stone / brick masonary wall surfaces in cm 1:4finished fair and even all as specified and as directed. 22 m&l for rendering 15 mm thick in cm 1:6 finished even without using extra cement over stone wall surfaces all as specified and as directed. 23 m&l for 10mm thick rendering in cm 1:3 on ceiling surfaces finished surfaces even and smooth without using extra cement complete all as specified and as directed. 24 m&l for 75mm thick pcc 1:4:8 type d 2, ( 40mm graded stone aggregate ) as in sub floor, sub bases, floor and paving etc; complete all as specified. 25 m&l for pcc 1:2:4 type b0 25 mm thickusing 12.5mm graded stone aggregates as in sub floors / base floors under tiles as in levelling course etc all as specified and directed. 26 m&l for machine cut kota stone slab flooring 18 20 mm ( + 2mm ) thick over cement screed base laid and jointed with greycement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 15mm thick screed bed or bedding layer in cm 1:4 complete all as specified and as directed. 27 m&l for mirror polished machine cut kota stone slab 15 16 mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in cm 1:4 and jointed complete all as specified and as directed. 28 m&l for 16 18mm thick granite ( colour as approved ) work ( table rubbed and polished ) in steps, shelves, jambs, pillars, window cills, cooking platforms ( vertical / horizontal ) and like in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite over and including 10mm thick screed bed or bedding layer in cm 1:4 complete all as specified and as directed. 29 cement concrete ( 1:2:4 ) type b 1 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and fair without using extra cement including provision of construction joints complete all as specified. 30 pressed steel framed made out of 1.25mm thick ms sheet, of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed. 31 cement concrete ( 1:3:6 ) type c 1 using 20 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etc., complete all as specified 32 cement concrete ( 1:2:4 ) type b 1 using 20 mm graded stoneaggregate as in lintels upto 1.50 m clear span, cills , steps, seismic and other similar bands, copings, kneelars, apex stones, bed plates, bedblocks of hold fasts etc including necessary form work complete all as specified 33 s&f of factory made 35 mm thick plain framed, panelled shutters ( two panel ) with 2nd class hard wood rail and stylewith lock rail and panel of 9 mm b.w.p. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. the size of rail and stile as per is : 1003 ( part i ) , kiln seasoned and chemically pressure treated complete all as specified. 34 s&f of factory made steel window box type using erw hollow p section comprising double frame for and including gauged and glazed skeleton shutter jointed internally with flat iron 40x4mm complete including grill of 8 / 10mm square bars as directed by engineer incharge, fixed horizontally @ 10cm c / c, hinges, handle, tower bolts, stops, lugs etc. ( with provision of fixing for cooler if required ) all as shown on drawing no cejz / td / 20 sheet 1 / 3 to 3 / 3 fixed in repairs i.e, incl taking down and removal of old steel windows from site or to store complete all as specified and directed. note: guard bar / grillshall be measured and paid separately under respective item of sch a. 35 s&f of sheet glass ordinary quality 4 mm thick and glazing with oil putty or fixed with wooden beads or fixed with rubber gasket in squares any size of pane complete all as specified & as directed. 36 mild steel round bars welded to steel windows or ventilators as in guard bars framed or unframed complete all as specified & as directed by engineer incharge.note: guard bars shall be factory welded & given one shop coat of red oxide or zinc chromate primer. cost of factory welding & shop coat of primer is deemed to be included in quoted rates. 37 s&f mild steel door handles, stove enameled black, 150 mm long and fixed with steel screws complete all as specified. 38 s&f of mild steel barrel tower bolts, stove enameled black, with bright bolt, 150 mm long and fixed with steel screws complete all as specified. 39 s&f of 300 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including bolts and nuts complete all as specified. 40 s&f of framed work as in doors chowkats of ms angle iron or ms hollow square / rectangular any type / size with gusset plates, rails, braces, cooler stand, chajja framed complete drilled for fixing of door etc; to be prepared for hanging with and including hold fasts and locking arrangements confirming to fe 290 ( gde e 165 ) complete all as specified and directed by engineer in charge. 41 m&l for 100mm thick pcc 1:4:8 type d 2, ( 40mm graded stone aggregate ) as in sub floor, sub bases, floor and paving etc; complete all as specified. 42 m&l for 60mm thick factory made pre cast cement concrete rubber moulded laquer finish using chemical and admixure inter locking tiles having compressive strength not less than 350 kg / sqcm, of shape and colour as approved by ge , laid over 25mm thickcompacted approved sand cushioned surface, joints filled by fine sand and compacting the top surfaces of paver blocks after laid etc of approved make all as specified and as directed. 43 m&l for factory made precast cement concrete solid blocks m 30 grade, using 20 mm graded crushed stone aggregate as in kerb stones of any size ( with plain or interlocking joints as directed ) set in cement mortar 1:4 for path edgings etc; embedded in position including all necessary excavation, tamping ground arround blocks and removal of rubbish / surplus soil etc., complete all as specified and directed by engineer in charge. 44 m&l for cement concrete ( 1:2:4 ) type b 1 using 20 mm graded stone aggregate as in kerbs or benching etc including necessary form work complete all as specified. 45 preparing new plastered surfaces and m&l for applying chalk whitening / concrete primer and / or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and m&l two coats of distemper oil emulsion on new plastered surfaces all as directed by engr in charge. 46 preparing new plastered surfaces and m&l for applying concrete primer and / or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and m&l two coats of cement base paint on new plastered surfaces all as directed by engr in charge. 47 preparation of newplastered surfaces of ceiling etc. & applying three coats of limewhite wash on ceilingcomplete all as specified. 48 preparing new or previously untreated surfaces of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. 49 preparing new or previously untreated surfaces of steel or iron work of any description and girth over 10cmand applying two coats of synthetic enamel paint complete all as specified andas directed by engineer in charge.. 50 m&l for point wiring ( concealed ) one light / fan point controlled by one 5 amps one way switch with 1.5 sqmm ( nominal area ) copper conductor flame retardant low smoke cable ( multi stranded ) pvc insulated and unsheathed electric cable 1100 volts ( isi marked ) drawn through pvc concealed conduit of suitable size ( as per conductor run ) with all fittings and accessories including pvc insulated unsheathed electric cable 1100 volts 1.5 sqmm ( multi stranded ) copper conductor single core ( green colour ) as continuous earth wire connected to common earth dolly including metal flush box made out of ms with hylum sheet suitable size and shape complete all as specified and directed by engineer in charge.. 51 all as per item no 50 above but for one 3 pin socket outlet 5 amps on independent board 52 all as per item no 50 above but for one 3 pin socket outlet 5 amps on same board 53 all as per item no 50 above but for one 3 pin socket outlet 15 ampsindependent with cable of size 4.0 sqmm for point wiring and 4.0 sqmm in continuous earth wire complete all as specified and directed by engineer in charge. 54 s & f switchpiano type 1way5a, 1 module 240 volts complete all as specfied and directed by engr in charge. 55 s & f switchpt 1way15a, 1 module, 240 volts complete all as specfied and directed by engr in charge. 56 s & f socket, 6a 2 / 3 pin combined 2 module, complete all as specfied and directed by engr in charge. 57 s & f socket6a / 16a 2 / 3 pin combined 2 module, complete all as specfied and directed by engr in charge. 58 s & f lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by engr in charge. 59 supply and fixing led lights fitting 1x 18w, 220v ac, metal ray plus is made of extruded aluminum channel with decorative dual color end caps providing a glare free evenly distributed light with driver, holder including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 60 supply and fixing led street light fitting 35 watt 230 v ac outdoor type with pressure die cast housing with toughned glass ingress protection of ip66, high power smd leds and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete all as specified. 61 ceiling rose surface backelite isi marked with 3 terminalincluding connecting and testing complete all as specified and dirted by the engineer in charge. 62 s&f distribution board sheet encloser powder coatedfor mcbs with bus bar 250 amps rated and neutral link earthing stud and degree of protection ip43 with door / mechanical resistance ik 07, spn 8 way 240 volts double door, concealed flush to wall surface complete all as specified and directed by the engineer in charge. 63 s&f distribution board sheet encloser powder coatedfor mcbs with bus bar 250 amps rated and neutral link earthing stud and degree of protection ip43 with door / mechanical resistance ik 07, spn 4 way 240 volts double door, concealed flush to wall surface complete all as specified and directed by the engineer in charge. 64 s& mcb, c curve type, 10 ka, 6 to 32 amp, single pole with over load and short circuit protection, complete all as directed. 65 s&f mcb, c curve type, 10 ka, 40amp, spn with over load and short circuit protection, complete all as directed. 66 supply and fix exhaust fan, steel body ac single phase. 230v of size 300m sweep with, blades, and frame and louvers with necessary making hole and finishing work as reqd at site complete all as specified and directed. 67 supply and fixing ceiling fans complete with blades, down rods, with 2 module electronic step type regulator and accessories, 230 v, 1200 mm sweep. min air delivery 210 cfm with service value 6.00 bee. 5 star rated with brushless direct current motor ( bldc ) compele all as specified and directed. 68 s&f vertical distribution board, double door, suitable for a frame fp mccb 125a made out of crca mild steel sheet surface with insulated material like polyester or with epoxy powder coating, vtpn 4 way, 415 volts with bus bar rating 250 amps, dust and vermin proof, suitable for incorporation of mcb’s and mccb etc and making all necessary connections, concealed flush to wall surface, complete all as specified and directed. note : mccb & mcb will be measured and paid separately under respective items 69 s&f mccb, a frame, thermal adjustable magnectic setting, ics = 75% 25 ka, 415v, 125 amp, 4 pole mccb with over load and short circuit protection, complete all as directed. 70 supply and fixing concealed sub main wiring with 2x10 sqmm single core copper conductor ( multistandered ) in concealed pvc frls conduit of suitable size as required, including single core 6.0 sqmm copper conductor as earth continuity all as directed. 71 supply, laying, testing and commissioning of lt ug cable, xlpe insulated, pvc sheathed, galvanized steel strip armoured electric power cable with stranded aluminium conductor, 1100 volts grade of size 35 sqmm 3.5 core confirming to is:7098 ( part i ) , suitable for earthed system, laid in duct / trench / along pole / wall etc including nuts, bolts, washers, saddles & screws etc and making connection, complete all as directed. 72 supply, laying, testing and commissioning of lt ug cable, xlpe insulated, pvc sheathed, galvanized steel strip armoured electric power cable with stranded aluminium conductor, 1100 volts grade of size 10 sqmm 2.0 core confirming to is:7098 ( part i ) , suitable for earthed system, laid in duct / trench / along pole / wall etc including nuts, bolts, washers, saddles & screws etc and making connection, complete all as directed. 73 earthing complete with galvanized steel earth plate electrode 600x600x6mm thickburied directly in ground ( earth pit not less than 2..25 mtr deep belownormal ground level ) with top edge ofearth plate not less than 1.5 mtr below the normal ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt, earth lead gi wire 4mm dia ( 8 swg ) connectd to gi earth plate elcectrode by means of bolts, nuts, check nuts, washers of galvanised iron, thimbles and other end of earth wire connected to main switch board and protected by galvanised iron pipe medium grade15mm bore and20mm bore medium grade gi pipewith funnel and wire mesh for watering all as shown in electrc plate no 5 connected to earth test point.40mm thick pre cast rcc m 15 ( nominal mix ) cover reinforced with xpm weight not less than 4 kg / sqm with suitable handle of 6mm dia ms bar and angle iron 40x40x3mm frame for cover, pcc chamber in cement concretem 15 ( nominal mix ) , excavation and earth work in any type of soil and connected all as specified and as directed by engineer in charge. 74 supplying and laying un reinforced precast concrete cable cover, class lv, type i, flat, size 250mm x 150mm x 40mm under ground cables for protection 75 m&l for sand cushioning with layer of sand 8cm thick before laying of cable and 10cm after laying of cable in trenches complete all as directed and sand cover to under ground cablecomplete all as directed. 76 m&l pipe galvanised iron light grade complete with all fittings laid in road crossing, and on pole, buildings complete all as specified and directed isi marked of 40mm bore...

Public Works Department - Rajasthan

33199731 various civil works in rajasthan secretariat under sectt. sub div i, jaipur. ( 2059 mtc and repair ) v providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m15 grade nominal mix 1: 2: 4 ( 1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size ) . 2 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size ) . 3 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in :cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) 4 half brick masonry in superstructure , above plinth level upto floor vlevelusing bricks of designation 75 cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) 5 plaster on new surface on walls in cement sand mortar 1:4 including rackingofjointsetc. complete fine finish :25 mm thick. 6 dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead:for thickness of tiles 25mm to 40mm. 7 demolishing r.c.c. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. 8 dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. 9 demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge:in cement mortar. 10 kota stone slab flooring 25 mm thick over 20 mm ( average ) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) for area of each slab from 2001 to 5000 sq.cm 11 providing and fixing designer cement concrete polished tiles over 20mm average thick base of cm 1 :4 ( 1 cement : 4 sand ) jointing with cement mortar 1 :2 ( 1cement : 2 sand ) with pigment to match the shade of the tiles complete with all respect. ( as per is 1237:2012 ) 12 grinding of existing floor with60, 80, 120 and360 no. carborundum stoneincluding cost of wax polishing complete : 13 add extra for mirror polishing on existing marble work / kota stone flooring work where ever required to give high gloss finish complete. 14 repair of existing steel glazed doors, windows and ventilator, ms sheet door, garge doors, compound wall gates etc. by welding drilling complete include. cost of welding rods and hire charge of welding meachine and tp etc complete 15 repair to damaged rcc slabs, beams and columns etc for strengtheing with cement mortar 1 : 2 in following stepsi ) choping losse and cracked concrete to required depth, cleaning the exposed surface of steel and concrete with wire brush and sand papering , cleaning of concrete surface with water as necessary and getting dried.ii ) applying epoxy primer on the exposed steel bars.iii ) applying epoxy hardener and resin mix ( as per manufectured s specification ) on concrete and steel bars with brush.iv ) speading dry cement mortar 1 : 2 mix over epoxy treated wet surface and allow it to dry for one day.v ) plastering the surface with cement sand mortar 1 : 3 upto depth of 30mm complete.vi ) cure the plastered surface for 15 days all work including scaffolding etc. complete in all respect. 16 making the opening inmasonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete to match existing surface i / c disposal of mulba / rubbish to the nearest municipal dumping ground.for door / windows / clerestory windows 17 making of holein r.c.c. slab / wall / beams and masonary wall ( width up to 450 mm ) by core cutting machine complete as per direction of eidiameter above 150mm 18 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.all kinds of soils 19 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 20 extra if square, rectangular hollow tubelarsections are used or grill made by flats onlyover item no 9.8.1 21 grading roof for water proofing treatment withwater proffing compoundcement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) 22 providing gola 75x75 mm in cement concrete 1:2:4 ( 1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge ) includingfinishing with cement mortar 1:3 ( 1 cement : 3 fine sand ) as per standard design : 23 providing and fixing in cm 1 : 4 double paitam ( rebated ) stone door window and ventilator frames of approved quarry :size 125 x 100mm 24 carriage of material building rubbish stone metal ( grit and ballast etc. ) including loading and unloadingfor 20 km. 25 providing and fixing marble stone flooring table rubbed, 15 18 mm thick over 20mm ( av. ) thick base of cm 1:4 ( 1 cement : 4 coarse sand ) jointing with white cement mortar 1:2 ( 1 white cement : 2 marble dust ) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. or providing and fixing stone slabs table rubbed, 15 18 mm thick in walls, steps, pillars, counters, jambs, shelves, sills etc. laid on 12mm ( av. ) thick base of cm 1:3 ( 1 cement : 3 coarse sand ) jointing with white cement mortar 1:2 ( 1white cement : 2 marble dust ) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. makranaadanga .above 3601 cm2 slabs 26 providing and fixing 1st quality mat finished ceremic tile size 300x300mm confirmingto is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete ( including the cost of cement mortar bed 1:4 ) . 27 extraforusingmarbleprinted / graniteshadeordarkshadetilesinsteadofwhite, grey, ivory, fumeredbrown, lightgreen, lightblueandotherlightshadesinandmatfinishedtiles. 28 extraforusing 400mm x 400mm mat finishedtiles in place of 300mm x 300mm size. 29 add extra for fixing glazed / ceramic / vitrified floor tiles with cement based high polymer modified quick set tile adhesive ( water based ) conforming to is: 15477 , using 5kg. adhesive per sqm of tile area, in average 3mmthickness instead of cement mortar. 30 p & f 1st qualityheavy duty vitrified polished digital tiles on floor, skirting and steps etc.in different sizes ( thickness minimum 10mm ) with water absortion less than or equal 0.08% and conforming to is 15622 of approved make in all colour and shade, laid with 20 mm thick cm 1: 4 including grounting the joints with white cement and matching pigment etc complete.size 600mm x 600mm 31 providing and fixing marble stone flooring table rubbed, 15 18 mm thick over 20mm ( av. ) thick base of cm 1:4 ( 1 cement : 4 coarse sand ) jointing with white cement mortar 1:2 ( 1 white cement : 2 marble dust ) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. or providing and fixing stone slabs table rubbed, 15 18 mm thick in walls, steps, pillars, counters, jambs, shelves, sills etc. laid on 12mm ( av. ) thick base of cm 1:3 ( 1 cement : 3 coarse sand ) jointing with white cement mortar 1:2 ( 1white cement : 2 marble dust ) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.keseriaji / abu ambaji ( green marble ) above 3601 cm2 slabs 32 providing and fixing granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12mm ( av. ) thick base of cement mortar 1:3 ( 1 cement : 3 coarse sand ) jointing with white cement mortar 1:2 ( 1white cement : 2 marble dust ) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.jhunjhunu / jalore ( red / choclate / black / pink colour ) above 3601 cm2 slabs 33 extra for providing edge moulding to 15 18mm thick marble / granite / kota stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. marble workfull edge moulding 34 extra for providing edge moulding to 15 18mm thick marble / granite / kota stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. granite / kota stone workfull edge moulding 35 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1 cement : 6 sand ) . 36 supplying and fixing in walls machine cut and polished stone shelves, tands andin cm 1:3 with machine cut edges :sand or other approved stone 50mm thick. 37 supplying and fixing stone lintels / bed plates of approvedquarryroughdressedincement mortar 1:4 :upto 15 cm. thick....

Urban Improvement Trust - Rajasthan

33117971 various civil works and maintenance works in sub division i area of division ii b ( arc ) civil works clearing and grubbing road land including uprooting rank vegetation, grass, brush, shrubs, saplings and trees of girth upto 300mm, removal of stumps, disposal of unserviceable material and stacking of serviceable material upto 1000m from road boundary. (morth specification : clause 201).by manual means : in area of light jungle 2 clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared. 3 silt clearance of drains, channels and canals with lift 1.5 mtr. and lead up to 50 mtr. 4 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils 5 add extra over item no. 1.8 and 1.9 (sechedule item no 1) for every additional lift of 1.5 m or part thereof : 6 above 1.50 to 3.00m 7 m 35,60mm thick to be used in light traffic (light traffic is defined as a daily traffic up to 150 commercial vehicles exceeding 30 kn laden weight, or an wquivalent up to 0.5 million standerd axles (msa) for a design life of 20 years (a standerd axle is defind as a single axle load of 81.6 kn ) like pedestrain plazes, shopping complexes ramps, car parks, office drveways , housing colonies , office complexes , rural roads with low volume traffic ,fram houses, beach sites, tourist resorts, local authority footwys ,residential roads, etc. 8 category bdenated only two side like i,z,t shape etc. as per irc sp 63:2004 9 random rubble dry stone kharanja under floor. 10 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 11 m10 grade nominal mix, 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 12 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix 13 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix 14 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix 15 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 16 anti termite treatment of floor using imidacloprid 30.5% ec non repellent, odorless, low dose, environimentally safe terniticide with rapid action non corrosive stain free manufactured by bayer or equivalent company by drilling 12mm diameter holes 300mm apart injecting the emulsion as specified by the manufacturer and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area dpe 12mm dia termitube system with required number of junction boxes are to be installed. the termitube will run all along the perimeter wall both inside and outside. in the middle area the termitube to be installed at an interval of 1.00 mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. after successful testing of termitube, pesticide emulsion of imidacloprid 30.5% ec mixed with water in the ration of 1:474 will be pumped by a motorized spray pump from the junction box in specified manner. the plinth area of the area treated will be measured for payment. 17 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for : 18 columns, pillars, posts and struts etc. 19 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in: 20 cement mortar 1:6 ( 1 cement : 6 sand). 21 cement mortar 1:4 ( 1 cement : 4 sand). 22 cement mortar 1:3 ( 1 cement : 3 sand). 23 random rubble stone masonry with hard stone in superstructure aboveplinth level and upto three levelabove 30cm. thick walls in : 24 cement mortar 1:3 ( 1 cement : 3 sand). 25 cement mortar 1:4 ( 1 cement : 4 sand). 26 cement mortar 1:6 ( 1 cement : 6 sand). 27 pointingonstonemasonryincementsandmortar 1:3 (1 cement : 3 sand) : 28 flush / ruled/ struck or weathered pointing. 29 providing and laying damp proof course with cement concrete grade m 150 (1 : 2 : 4) mortar prepared with 1% solution of water proof compound complete and not applying 2 coats of hot bitumen complete as per specifications. 75mm thick 30 50mm thick 31 75 mm thick 32 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for : 33 suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 34 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. 35 thermo mechanically treated bars (conforming of relevent is code) 36 flyash flyash brick work with flyash flyash bricks of class designation 75 in superstructure above plinth level upto floor three level in all shapes and sizes in : 37 cement mortar 1 : 4 (1 cement : 4 coarse sand) 38 cement mortar 1 : 6 (1 cement : 6 coarse sand) 39 half flyash brick masonry in foundation & plinth using flyash bricks of designation 75 40 cement mortar 1 : 4 (1 cement : 4 coarse sand) 41 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 42 12mm thick. 43 20mm thick. 44 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3 fine sand) 45 making grooves as per design in plaster 10mm to 20mm wide. 46 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 47 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : 48 two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. 49 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. 50 new work 51 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 52 painting with synthetic enamel paint of approved brand and manufacture togive an even shade : 53 two or more coats on new work 54 150cm high fencing with angle iron 50x50x6mm. placed at every 3mtr. apart 30cm. in ground embedded in cement concrete 1:3:6 (30x30x45cm) corner and every tenth post to be strutted with 50x50x6mm. angle iron provided with 6 horizontal lines and two diagonals of black barbed wire between two posts fitted and fixed with g.i. staples including earth work in excavation etc. complete. 55 grading roof for water proofing treatment withwater proffing compound 56 cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 57 providing and fixing pressed steel door frames confirming to is 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike plate and shock absorbers as specified and applyinga coat of approved steel primer after pre treatment of the surface including filling with cc 1:2:4(m15 grade) complete as directed by engineer in charge : 58 profile b 59 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure a: 30 mm thick . 60 decorative teak veneer both side 61 providing and fixingaluminum workfor doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285,fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required pvc/neoprene felt etc. aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing /paneling , c.p. brass/ stainless steel screws al. tower bolt & al. handle & al. aldrop etc.,all complete as per architectural drawings and thedirections of engineer in – charge .(glazing and paneling to be paid for separately). : for fixed portion 62 polyester powder coating aluminum( minimum thickness of powder coating 50 micron) 63 providing and fixing of plastic shutter infill made from extruded multi chamber hollow p.v.c. section having cross section of 200 x 20 x 1 mm and shutter frame made from extrude p.v.c. section in the configuration of double walled c section having an overall cross section of 40 x 37 mm and door fittings such as hinges, aldrop, handles, stopper, locking bolt will be provided. 64 providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (is 1038 1983) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required :partly fixed and partly openable [ fixed area not to exceed 33%] 65 for shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). 66 polyester powder coating aluminum( minimum thickness of powder coating 50 micron) 67 providing and fixing superior quality like hardvyn or equivalent hydraulic door closure. 68 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 300mm x 450mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 69 providing and fixing 1st quality mat finished ceremic tile size 300x300mm confirmingto is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). 70 providing and fixing 15 to 20 mm thick granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12 mm (av.) thick base of cement mortar 1 : 3 (1 cement : 3 coarse sand) jointing with white cement mortar 1 : 2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of : 71 good quality south black above 3601 cm2 slabs 72 extra for providing edge moulding to 15 18mm thick marble/ granite stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. 73 granite work (full edge moulding ) 74 p & f 1st quality heavy duty vitrified glazed mat tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to is 15622 of approved make in all colour and shade, laid with 20 mm thick cm 1: 4 including grounting the joints with white cement and matching pigment etc complete. 75 size600 mm x 1200mm 76 providing & fixingbrown kota/ mandana / dholpur/ slate stone incladding / flooring structuralbase with white cement & tinex chemical& ss clamp and fasteners (of approved brand) laid and jointed with white cement slurry mixed with pigment to match the shade of the slab as per drawing attachedcomplete in all respect as per direction of engineer in charge & architect with all lead & lift. the stone measurement will be done of outer most dimension. thickness of stone 25 30mm. 77 polished blue kota stone flooring skirting, laid over 20 mm thick base of c.m. 1 : 4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete :for area of each slab from 901 to 2000 sq.cm : 78 25 mm thick slab. 79 s/f of fire bricks on edg flooring with fire bricks suitable for 1300 degree centigrade safe working temperature as per is :8 specification laid on & filling of joint by fire resistant mortar/adhesive of required thickness as per directed on a bed of 20 mm thick 1:2 cement mortar of bricks 9 x 4.5x 3 (rate approved year 2008) 80 providing and fixing of glass moisac tiles ( bisseze marke ) size 20 x 20 x 4 mm applied with aaproved adhesive as per specification and direction of engineer in charge 81 providing and fixing staincase railing 90 cm high from nosing of made offollowing specifications. 82 50 mm outer dia (2 mm thick) s.s. pipe hand rail. 83 40 mm outer dia (2 mm thick) s.s. pipe baluster @ 1.00 mtr. 84 4 nos. 20 mm fs. s pipe intermediate runners parallel to hand. 85 s.s. shoe 1.60 mm thick 75 mm outer dia. at each baluster 86 baluster to be welded with s.s. plate 50 mm dia (3 mm thick) anchored in c.c. block with suitable dash fastners 87 50 mm dia & 2 mm thick s.s. pipe for start and end vertical ornamental posts to be provided as per direction of engineer in charge 88 the stainless steel work shall be brushed steel finish with all joints/welds properly grinded to final finish. the stainless steel shall be 304 grade and shall confirm to relevant i.s. 89 providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide.extra if square,rectangular hollow tubularsections are used or grill made by flats only 90 decorative plaster work with spectrum textured coating as per approved colour and shade complete as per manufactures specifications. 91 grit textured @ 2.5 to 3.0 mm thick. 92 ornamental cement plaster in cement sand mortar1 : 4 making kangooras etc. as per jaipurpractice. 93 supplying and fixing machine cutdressed 75 mm pinksand stone (bansi paharpur) dasa/ coping wth ornamental shape having moulding and pan shape engraving as per required pattern with engraving depth of 5 mm (average) in single piece of length 90 cm to be laid on cement mortar 1:4 (12 to 20mm thick) including pointing with admixture of pigment matching with the stone shade. 94 providing corrugated g.s. sheet roofing including vertical / curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces)excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required. 95 0.63 mm thick with zinc coating not less than 275 gm/m2 96 supply & spreading ofgood earth at site complete including loading unloading & transportation etc. 97 supply of dry manure including loading unloading,transportation & stacking at site. 98 farm yard manure(organic) 99 spreading of manure and good earth in required thickness (cost of manure and good earth to be paid separately). 100 laying of lawns including ploughing levelling breaking of clods manuring & removal of stones etc.(cost of manure or extra good earth to be paid seperately) maintenance of lawns for 30 daysor more till the grass forms a thick lawns free from weeds & fit fo 101 in rows 7.5 cms. apart in either direction 102 construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting by vibratory roller 8 10 tonne to meet requirement of table 300 2 including cost of compensation for earth taken from private land with lead upto 1 km as per morth specification : clause no. 305. 103 rough chisel dressed stone flooring over 20 mm (av.) thick base in cm 1 : 6 including pointing with cement mortar 1 : 2 (1 cement : 2 stone dust) with and admixture of pigment to match the shade of stone with joint thickness upto 15 mm : 35 mm thick red sand stone. 104 p & f european type white glazed vitreous china 1st quality double syphonic w.c (is :2556 mark) with p or s trap including cutting and making good the wall and floor 105 p & f indian type white glazed vitreous china 1st quality w.c. orissa pan (is :2556 mark) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor: 106 size 580x440mm. 107 p & f low level flushing cistern of 10 ltr. capacity (is : 2556 mark) o9f approved make with colplete fitting ,c.i. brackets duly painted , brass ball cock with ball, (is :1703 mark)complete including cutting and making good the wall. 108 wvc with c.p. brass bend. 109 p & f wvc wash basin (1st quality, i.s. : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p. pillar cock (is : 8934 mark) &32 mm c.p. brass waste coupling of approved make, 25 mm g.i. waste pipe complete including cutting & making good the wall.: 110 size 550 mm x 400 mm dia for counter top 111 1.0 mm thick salem stainless steel aisi 304 & is 13983 1994kitchen sink of approved make (nirali, neel – kanth, jaina, faber castell )with large waste coupling. 112 (24 x 18 x 8) (20x16x8) 113 p & f inlet connection (angle valves) superior quality, of approved make, for wash basin, gyser etc. 114 c.p. inlet connection 15mm.brass (is : 8931 marked) with 37 cm long pipe and nut. 115 p & f pvc storage tank isi marked (is : 12701) indicating thebis license no),of approved make with cover, 25mm dia 1m long g.i. over flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 116 1000 litres capacity. 117 providing and fixingsuperior quality (jaguar contiental ) cp brassfittings complete as per direction of ei 118 bib cock with long thread 15 mm nominal size 119 brass / gunmetalhalf turnwt. 1 kg.ofapprovedquality / make,25mmnominalbore. 120 p & f full way valve (is:778 mark) or wheel valve of approved make 121 gun metal 32mm nominal bore. 122 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. (concealed work including cutting chases and making good the walls etc.,) 123 20mm nominal outer dia pipes 124 32mm nominal outer dia pipes 125 p&f rigid pvc pipe (is:4985 mark) class ii/ (4 kg. /cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 126 110 mm dia 127 160 mm dia 128 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant: 129 coupler (socket) 130 110mm dia 131 160 mm dia 132 plain tee 133 110mm dia 134 160mm dia 135 door tee 136 110mm dia 137 bend 45 138 110mm dia 139 vent cowel 140 110mm dia 141 door bend (left & right) 142 110mm dia 143 pipe clip 144 110mm dia 145 plain floor trap 146 110mm dia 147 p trap 148 110mm dia 149 socket plug 150 110mm dia 151 door cap 152 110mm dia 153 construction of chamber in all type of soil with 300 mm thick masonry in cm 1:6 m 10 cm thick c.c. 1:5:10 in foundation, 20mm thick insider plaster in cm 1:6, finished with floating neat cement, 50mm thick m 15 grade c.c. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. 154 do size 450 x 450mm depth upto0.5 m cement cover with frame 155 wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) ofapproved make in surface / recessed isi marked medium duty pvc conduit & its accessories, round tiles,hot dipped galvanized modular box with earth terminal, 6 a modular switch,modular plate with grid plate,screws,making connections, testing etc. as required. 156 short point (up to 3 mtr.) 157 medium point (up to 6 mtr.) 158 long point(up to 10 mtr..) 159 wiring of twin control light point with 1.5 sq.mm fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade and 1.5 sq.mm.fr pvc insulated unsheathed flexiable copper earth conductor 1.1 kv grade(is: 694) of approved make in surface/ recessd isi marked medium duty pvc conduit & its accessories, round tiles, 18 swg m.s. box with earthing terminal, 6 amp two way switch, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. 160 medium point (up to 6 mtr) 161 wiring of 3 pin 6 amp light plug point with 1.5 sq.mm fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade and 1.5 sq.mm.fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade(is: 694) of approved make in surface/ recessd isi marked medium duty pvc conduit & its accessories, round tiles, 18 swg m.s. box with earthing terminal, 6 amp switch & 6 amp socket, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. 162 on board 163 medium point (up to 6 mtr) 164 long point (up to 10 mtr) 165 s&f following sizes (dia.) of isi marked medium duty pvc conduit along with accessories in surface / recessed using saddles, clamps, fastener as required includingcutting the wall, covering conduit and making good the same as required. 166 25 mm 167 32 mm 168 50 mm 169 supplying and fixing of power plug point modular accessories on hot dipped galvanized modular on surface or in recessed with suitable size of grid plate with cover plate including cost ofmodular 16 amp. switch and socket outlet, making connection , testing , etc. as required. 170 p&f metal clad industrial plug top & socket unit with pin and sleeve type contact on porcelain/ bakelite base in sheet steel enclosure (without mcb) including making connections, testing etc.as required 171 single / double pole(three pin) 172 32 a 173 providing & fixing isi marked 6 amp bakelite batten/angle holder including making connection testing etc. as required. 174 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor isi marked (is:694) of 1.1 kv grade and approved make in existingsurface or recessed conduit/casing capping including making connections etc. as required. 175 2 x 2.5 sq. mm. + 1x1.5sqmm 176 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 177 p&f 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c/ d tripping characteristic) isi marked is 8828(1996)]/ conforming to iec 60898 in existing board/sheets including making connections, testing etc. as required. 178 single pole mcb 179 6 a to 32 a rating 180 four pole mcb 181 40 a 63 a rating 182 four pole mcb 183 6 a to 32 a rating 184 p&f recessed/ surface mounting heavy duty horizontal type sheet steel distribution board phophatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar,masking sheet, conforming to is13032 & is8623 including making internal dbterminations with copper lugs , testing etc. as required. 185 double door (single phase) 186 12 way 187 double door (three phase) 188 8 way 189 p/laying p.v.c./ xlpe insulated & p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor of is:1554 p i / is :7098 p i of group 1 of approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand,iind class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. 190 25.0 sq.mm 191 4 core 192 50.0 sq.mm 193 120.0 sq,mm 194 3.5 core 195 150.0 sq,mm 196 supplying and making one end termination with heavy duty single compression brass gland sibg type, heavy duty aluminium lugs duly crimped with crimping tool, pvc tape etc for following size of armoured pvc insulated & pvc sheathed/ xlpe aluminium conductor cable of 1100 volt grade as required of size. 197 3.5 x 120.0 sq.mm 198 4 x 25.0 sq.mm 199 p/laying p.v.c./ xlpe insulated & p.v.c. sheathed cable of 1.1 kv grade with copper conductor of is:1554 p i / is :7098 p i of group 1 of approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand,iind class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. 200 10.0 sq.mm 201 4 core 202 supplying and making one end termination with heavy duty single compression brass gland sibg type, heavy duty copper lugs duly crimped with crimping tool, pvc tape etc for following size of armoured pvc insulated & pvc sheathed/ xlpe aluminium conductor cable of 1100 volt grade as required of size. 203 4 x 10.0 sq.mm 204 sitc of wall/ free standing floor mounted dust and vermin proof compartmentalisedcubical panel made out of crca sheet , required hardware,duly treated for derusting in 7 tank process with dephosphating and with powder coating on both side of panel in desired shadethe panel having pu/ neoprene rubber gasket of not less than 3mm thickness , separate detachable gland plate m.s. base channel ,hinged door with locking arrangement for equipment/switchgear. thickness of sheet shallnot be less than 1.6 mm up to 600 mm length / widthof any compartment and be of 2.0 mm above 600 mm. load bearing structure shall beof 2.0 mmthick sheet supported by base m.s. channel if required . side walls and cable alley compartments having bolted type doors with / withoutdetachable extension type structure. (only outer area on all sides shall be measured & panel to be fabricated from cpri approved fabricator) 205 supplying and fixing of aluminium / copper bus barby means of smc / dmc type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. 206 electrolytic grade aluminium bus bar 207 sf of (0 500) v range volt meter on existing panel , making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required. 208 analog type ( 96mm x 96mm ) 209 sf of ct operated direct reading typeampere meter on existing panel , making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required. 210 analog type ( 96mm x 96mm ) 211 below 500 a 212 sf ofcurrent transformer, with all necessary support in existing panel including connection etc. as required . 213 up to 150/5 ratio, 10 va, class 1 accuracy 214 sf of selector switch of 10 a for voltmeter (4 position ) including making connection etc.as required . 215 sf of ct linked selector switch of 10 aforampere meter (4 position ) including making connection etc.as required . 216 sf of110/220 v, led (22.5 mm dia ) indicatinglamp with integral circuit, terminal block, including connection etc. as required. 217 red/yellow/green colour 218 supplying and drawing fr pvc insulated & unsheathed flexiable copper conductor isi marked (is:694) of 1.1 kv grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. 219 1 x 1.5 sq.mm 220 1 x 2.5 sq.mm 221 1 x 4.0 sq.mm 222 1 x 6.0 sq.mm 223 sitc of self healing mpp/mp type shunt capacitor (banks) conforming to is:13340 41 / iec :831 1&2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( psd ) and shall have dissipation factor less than 0.0025 at 50 hz and total wattage loss less than 0.5 watt per kvar . including making connections with suitable capacity conductors/cables testing etc. as required. 224 heavy duty three phase 440 v , 50 hz capacitor (bank) 225 sitc of microprocessor based three phase sensingpower factor correction relay having following sensing capacitysecondary current , self analysing auto c/k setting according to targeted power factor setting, the relay shall havedigit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, indication of switching on units, auto/manual status, and shall have over load protection, no volt release , having multi parameter like kw, kva, kvar,metering facility as required. 226 6 to 8 stage 227 sensitivity upto 50 milli amp 228 p & f ofcam operated rotary switchs on existing panel with 2 way and off postion 229 one pole 230 16 amp 231 p & f of440 volt 3 pole capacitor(ac 6 b ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors/ reactors to limit the inrush current, conforming to is:13947 4 1/iec:947 4 1, din rail mounting type including making connections, testing etc. as required. suitable for following capacity capacitor bank. 232 up to 6 kvar 233 7 to 10 kvar 234 p&f 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c/ d tripping characteristic) isi marked is 8828(1996)]/ conforming to iec 60898 in existing board/sheets including making connections, testing etc. as required. 235 triple pole mcb 236 6 a to 32 a rating 237 p&f on load change over switch, front handle operated, four pole 415 v conforming to is:13947 p iii including connections , testing etc. as required in the following rating: 238 open execution type 239 200 amp 240 sitc of quick make and quick break4 polecurrent limiting mccb having following current rating, short circuitbreaking capacityat 440/415 v, 50 hz; o/l & s/c settings and conforming to is 60947 2 / iec 60947 2 with front face and centralised adjustable, line load interchangeability, having positive isolation capability, provision for uvr , shunt trip ,earth fault trip, push( test) to trip , including making connections with lugs & spreaders,etc. as required. 241 with thermal magnetic release 242 up to 160 amp , 25 ka, adjustable o/l & fixed s/c setting, ics = 100 % icu 243 plate earthing as per is:3043 withcopper earth plate of size 600mm x 600mm x 3.0mm by embodying3 to 4 mtr. below the ground level with 25mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer, nipple ,wire meshed funnel, and c.c.finished chamber covered with hinged type with locking arrangement c.i. cover,c.i. frame of size300mm x 300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required. 244 s & laying following size earth wire/stripin horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required. 245 8 swg copper wire 246 providing & fixing of heavy duty capacitor start 900/1400 rpm single phase isi marked exhaust fan is:2312 marked in existing opening making connections, testing etc. as required 247 300 mm sweep (900/1400 rpm) 248 p & f double ball bearing capacitor start, aluminium body & blade ceilingfanwith down rod up to 30 cm with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. 249 1400 mm sweep 250 p & f of ip 20 led tube light 20 watt with external batten made from crca sheet steel suitable to replace t 8/t 12 tube light, integral driver, 2000 luman + 5% tolerarrce system luman efficiacy of 100 lm/ watt minimum expected life time of 25000 burning hours, cct 5700 k ansi, cri 80, driver efficiency >85%, life expectancy of driver rnin 30000 hrs. pf 0,95 at full load/ 230 volt ac. 251 p & laying xlpe insulated is:7098/ii/85 of group1 and approved make h.t.cable for working voltage 11 k.v.earthed direct in ground including excavation of 30cmx100cm size trench, 25cmlayer of river sand, iind class bricks covering, refilling earth, compaction of earth, making necessary connection testing etc.as required of size. 252 3 core 185.0 sq.mm ...

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

33104393 remaining work at gsss salari ( art and craft room ) block kekri district ajmer remaining work at gsss salari (art & craft room) block kekri district ajmer sl. no. item description 1 civil work 2 earth work in excavation by mechanical means ( hydraulic excavator)/ manual means in foundation trenches or drains(not exceeding1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, incuding taking out the excavated soil and depositing and refilling of jhirri with watering and ramming and disposal of surplus excavated soil as directed with in a lead of 50m. all kind of soils 3 providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8(1 cement:4 coarse sand :8 graded stone aggregate 40 mm nominal size). 4 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in cement mortar 1:6 (1 cement : 6 sand) 5 centering & shuttering with plywood or steel sheets including strutting propping, bracing both ways and removal of formworksfor foundation infootings , straps beams , raft ,bases of coloumns etc. 6 providing and laying in position specified grade of cement concrete for all rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement . m20 grade nominal mix / design mix 7 providing and laying in position specified grade of cement concrete for all rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement . m20 grade nominal mix / design mix / for column add extra for providing m25 grade concrete by using min. 410 k.g. of cement per cum instead of m25 grade design mix. 8 random rubble dry stone kharanja under floor . 9 brick work with mechanised autoclaved flyash lime bricks conforming to (is:12894 :2002) of class designation 100 in super structure above plinth level up to floor five level in cement mortar 1:6.(1 cement : 6 coarse sand) 10 centering & shuttering with plywood or steel sheets including strutting propping, bracing both ways with steel props and removal of formworks for upto floor five levelfor suspended floors, roofs, landings staircases balconies, girders, cantivlevers bands,coping bed plates anchor blocks sill, chajjas, lintel beams, beams, plinth beam etc. 11 centering & shuttering with plywood or steel sheets including strutting propping, bracing both ways with steel props and removal of formworks upto floor five levelfor columns, pillers, posts and struts etc. 12 providing and laying in position specified grade of cement concrete forrcc structural elements upto five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required)excluding the cost of centering, shuttering and reinforcement for walls (any thickness) including attached pilasters, buttresses, plinth and string coarses,fillets, columns, pillars, piers,abutements, posts and struts etc.m 20 grade nominal mix/design mix.add extra for providingm 25 grade concrete by using min. 410 k.g. of cement per cum instead of m 20 grade design mix 13 providing and laying in position specified grade of cement concrete forrcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required)excluding the cost of centering, shuttering and reinforcement for beams, suspended floors, rofs, griders, having slopes up to 15 degree, landings, balconies, shelves chajjas, lintels, bands plain window sills, staircases and spiral staircases etc.m 20 grade nominal mix/design mix. 14 providing and fabricating reinforcement for r.c.c. work including strengthening, cutting, bending, placing in position and binding including cost of binding wire all complete up to floor five level.(original producers who manufacture billet directly from iron oras and role the bilets to produce steel conforming to is:1786) tmt bars(conforming of relevent is code) 15 plaster(internal)plaster on new surface on wall in cement sand mortar 1:6 including ranking of joints etc. complete fine finish : 12 mm thick. 16 plaster(external)plaster on new surface on wall in cement sand mortar 1:6 including ranking of joints etc. complete fine finish : 20 mm thick 17 kota stone slabs 25 mm thick in risers of step skerting, dado and pillars laid on12mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete for area of each slab upto 2001 sqcm. 18 kota stone slabs flooring 25mm thick over 20mm (averege) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coare sand) for area of each slab from 2001 to 5000 sqcm. 19 s&f in walls machine cut & polished stone shelves ,tands andin cm1:3 with machine cut edges : kota stone minimum 30 mm thick. 20 providing and fixing ms sheet 1mm thick single leaf doors shutter in angle iron frame 35x35x5mm suitabilly digonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of engineer incharge but excluding cost of chowkhats including two coats of anti corrosive red oxide primer paint. add 20 % extra for double leaf shutter. 21 providing and fixing t iron /frames for doors, windows and ventilators of mild steel tee section joints mitred and welded with 15 x 3 mm lugs, 10cm . long embedded in cement concrete blocks, 15 x 10 x 10 cm of1:3:6 (1 cement, 3 coursed sand and 6 graded stone aggregate 20 mm nominal size or with wooden plugs and screws or rawl plugs and screw or with fixing clips or with bolt and nuts as requesting including fixing of necessary butt hinges and screw and applying a priming coat of approved steel primer 22 providing and fixing steel glazed doors windows and ventilator shutters of standarad rolled steel section (is:1038 1983) joints mitred and welded with steel lugs 13x3mm,10cm long embedded in cement concrete block 15x10x10cm of 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size )or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with coper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approved steel primer, excluding the cost of metal beading and other fittings expect necessary hings of pivots steel handles peg stay etc.as required partly fixed and partly openable.(fixed area not to exeed 33%) 23 supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. 24 providing and fixing square bars or other flat welded to window ventilators etc 25 panting on doors & windowspainting with synthetic enamel paint of approved brand and manufacture to give an even shade : (2 or more coat on new work ). 26 providing and applying white cement based putty overplastered surface to prepare the surface even and smooth complete new plaster surface (three or more coats) 27 finishing walls with acrylic smooth exterior paint of required shade including all scaffolding new work (two or more coat applyied @1.67 lt. per 10 sqm over an including base coat of water proofing cement paint applyied @ 2.20 k.g. per 10 sqm. 28 distempering with oil bound washable distemper of appd. brand and manufacture to give an even shade inc. all scaffolding new work (2 or morecaot) over and inc. scrapping and priming coat with cement primer. 29 providing gola75 mm x 75 mm in cement concrete (1:2:4)(1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge )including finishing with cement mortar 1:3( 1 cment : 3 fine sand ) as per standard design. 30 providing and fixing 20 mm thick precast terroze tiles of approved make with marble chips of size up to 6mm laid over roof with neat cement slurry mixed with pigment to match the shade of tiles including cutting grinding , rubbing with machine complete on 20mm thick bed of cement sand mortar 1 :4. 31 p& f rigid pvc pipe (is 4985 mark) class 2nd /(4 kg /sqcm) approved quality / make including joining the pipe with solvant cement rubber ring and lubricant 110 mm dia. 32 supplying and fixing machine cut fine dressed red/ pink sand stone dasa or coping with full moulding if required laid on cement mortar 1:4 including pointing with admixture of pigment matching with the stone shade 50mm thick coping 33 electrical work 34 s&f following sizesof isi marked ( is:14927 p ii ) upvc casing capping as per pwd specification for electrical works along with all accessorieslike coupler, inner, outer, elbow, square box, tee, end cap etc. on surfacewithscrews, expansionfasteners , all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for additional technical parameters of products/ work, referannexure a attached with this bsr . 25mm x 12mm 35 p & f 18 swgm.s. recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 36 wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (as per is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (as per is:694) on surface isi marked ( is:14927 p ii ) upvc casing capping& its accessories like coupler, inner, outer, elbow, square box, tee, end cap etc., recessed 18 swg g. i. box with earth terminal/surface upvc boxwith earth terminal, 6 a switch 3 pin ceiling rose / lamp holder/ 3 point connector , 3.0 mm thick isi marked phenolic laminated sheet (is : 2036 1995),al. alloy/ cadmium plated iron screws 20 mm cup washers etc., all as per pre approved by engineer in charge,making connections, testing etc. complete as required. for specification of copperconductor,phenolic laminated sheets & electrical/ wiring accessoriesrefer chapter e 04, e 05 & e 07 . for additional technical parameters of products/ work, referannexure a attached with this bsr .short point ( up to 3 mtr. ) 37 medium point (up to 6 mtr.) 38 long point(up to 10 mtr..) 39 wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade(is:694) inrecessed isi marked ( is:9537 p ii ) rigid steel conduit & its all accessories,required size 18 swg, g.i. box with earth terminal, 6 aswitch, 3/5 pin 6 a socket, 3.0 mm thick isi marked phenoliclaminated sheet, pvc bushes, check nuts,al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by engineer in charge, making connections, testing etc. complete as required.for specification of copperconductor,phenolic laminated sheets & electrical/ wiring accessoriesrefer chapter e 04, e 05 & e 07 .for additional technical parameters of products/ work, referannexure a attached with this bsr . on board 40 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.99% purity copper, class 5 stranding in acc. to iec 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4,, in existingsurface or recessed pvc/ ms conduit/casing capping includingall as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work, referannexure a attached with this bsr . 3x2.5 sq.mm 41 providing & fixing of 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c tripping characteristic as per type of load andsite requirement) 4kv impulse withstand voltage,as per pwd specification for electrical works with isi marked is 8828(1996) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec,minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted withexisting distribution board/sheets, min. operation 20,000 upto 32 a rating and 10,000 upto 63 a, 5000 for 80 a ratingincluding making connections, testing etc. as required.. oem shall have submitnabl / cpri / erda accrediated lab test reportsbefore execution & all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 6a to 32a rating 42 50/63 arating 43 providing & fixing of ik09 recessed/surface mounting heavy duty horizontal type sheet steel of 1.6 mm thickdistribution board as per pwd specificationfor electrical works isi marked conforming to is 13032 & is 8623 / conforming to iec 61439 3. phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal dbterminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.oem shall have submitnabl / cpri / erda accrediated lab test reportsbefore execution & all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 4 way (4o/g+2i/c) 44 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coatedhousing with in built driver, power consumption of18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k/ 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsr.4 led tube shape fixture 18/20 w (extruded albase) 45 providing & fixing of iso certified company made beestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanas per pwd specification for electrical works, conforming to is:374 2019, & is:1885 p v 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required.appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 1200 mm sweep bee 3 star rated (service value >=5.0 to< 5.5 ) 46 providing & fixing of non modular socket size flush type 180 watt rotary minimum 5 step fan regulator as per pwd specification for electrical works, isi marked (is:11037) made out from industrial grade polycarbonate or fire resistant abs material including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 47 providing & fixing of 18 swg g. i. / m .s. sheet boxesas per pwd specification for electrical works, duly finished with two coats of red oxide and with earthing terminal of following sizes (nominal size) in recessed/surface as required. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 175mm x 100mm x 60mm 48 providing & fixing of p.v.c. sheet 2.0 mm thick offollowingsizeincluding screws, cup washer as required. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr .75 mm dia. 49 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un armoured / armouredaluminiumcable of 1.1 kv grade as per pwd specification for electrical worksin existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench with filling of excavated earth in trench, on existing cable trays or on surface etc.including making necessary connection, testing etc. as required of size andas per points (a), (b), (c), mentioned below: (a) material : h4 gradealuminium conductor of purity >99.6 %& as peris:1554 p i / is :7098 p i(b) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures .(c)oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities forcables . appropriate type test certificate / oem test report shall be submitted .all above as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr 4sq.mm 2 core ...

Rajasthan Tourism Development Corporation Limited - Rajasthan

33038325 furbishment work at paryatan bhawan jaipur furbishment work at paryatan bhawan jaipur carriage of building rubbish stone metal etc to a distance upto 10 km including safely stacking of material all as per instructions and directions. 2 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.m15 grade nominal mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size) 3 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix / design mix 4 centering & shuttering with plywood or steel sheets includingstrutting, propping bracing both ways with steel props and removalof formwork for upto floor five level for :suspended floors, roofs, landings, staircases, balconies, girders,cantilevers, bands, coping bed plates, anchor blocks, sills,chhajjas, lintel, beam, plinth beam etc. 5 providingandfabricatingreinforcement forr.c.c.workincludingstraightening, cutting, bending, placing in position and binding including cost of binding wire) all complete up to floor five level. thermo mechanically treated bars (conforming of relevent is code 6 brick work with f.p.s.bricks of class designation 75 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1 : 6 (1 cement : 6 coarse sand) 7 half brick masonry in superstructure , above plinth level upto floor v level using bricks of designation 75cement mortar 1 : 4 (1 cement : 4 coarse sand) 8 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. 9 providing & fixing door, window, chowkhats and other frames, including antitermite treatment, m.s. flat, hold fasts of size 250 x 40 x 3mm fixed with m.s. bolt 5mm dia 50mm long duly embedded in cement concrete m 15 grade : ghana teak wood grade i. 10 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked usingphenol formal dehyderesin in glue both sides with approve steel fittings complete as per annexure a 35 mm thick. decorative teak veneer both side 11 extra for providing external lipping with 2nd class teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) over item no. 8.13. 12 extra for providing other type of fittings as mention in annexure a ( as approved by ei) : brass fittings 13 providing and fixing is : 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. 14 providing and fixing nigeria / ghana /ivory coast, teak wood grade i mouldings and beadings in doors and windows size : 15 25x12 mm 16 25x20 mm 17 providing and fixing bright finished mortice lock of approved make godrej or equivalent with pair of cp handles for doors with necessary screws etc complete (best make of approved quality) as per direction of engineer in charge. 18 extra for providing brass handle instead of cp handle 19 providing and fixing granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12mm (av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.good quality south black, area above 3601 cm2slabs 20 extra for providing edge moulding to 15 18mm thick marble/ granite/kota stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer incharge. granite/kota stone work half edge moulding 21 extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete 22 extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location inmarble/granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete 23 steel work in built up tubular trusses including cutting, hoisting (height upto 10 m)fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete. hot finished welded type tubes. 24 supply and installation of multi rib proofing/cladding sheet manufacture out of 0.60mm tct (total coated thickness) high tensile zinc aluminum alloy coated galvaiumeseel (as per 150gsm zinc aluminum coated 550mpa tuekd strength) confirming to is: 1397/astm a 792 sheet to have wide pens 30mm high nb at 250 centre and centre width of 1020mm shets be casted with regular modified plyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have proportionality with siphoned plate at made at toprevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. the sheet shall be supplied in cost one length and foe a minimum up to 12mts with all scaffolding. 25 removing dry or oil bound distemper by scrapping sand papering and preparing surface smooth including necessary repairs to scratches by sandla/loi and all scaffolding (for colour changing only) 26 french sprit polishing : two or more coats on new work including a coat of wood filler. 27 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete 28 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. 29 providing and applying superior quality wall painting with velvet touch emulsion paint of approved brand and manufacture to give an even shade with putty and preparation of surface applying with the help of paint roller the work complete in all respect as per direction of engineer in charge. new work three or more coat 30 finishing walls with acrylic smooth exterior paint of required shade including all scaffolding.new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). 31 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work 32 demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer in charge. 1: 3: 6 or richer mix. 33 dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: for thickness of tiles 10mm to 25mm. 34 dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. 35 removing aluminium/gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by engineer in charge. 36 providing and fixing sun control film, thickness of film 1 mil visible light transmittance 4 24% & solar energy transmittance 42 51% & total solar energy rejection 37 43% of approved colour and shade , complete in all respect , at all level , as directed by engineering charge. 37 providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. 38 gi metal ceiling lay in perforated tegular edge global white colour tiles of size 595x595mm and 0.5 mm thick with 8 mm drop made of gi sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having nrc (noise reduction coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation and backed with a black glass fiber acoustical fleece. ...

Public Works Department - Rajasthan

32612052 various civil works in rajasthan secretariat under sectt. sub div ii, jaipur. ( 2059 mtc and repair ) brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in :cement mortar 1 : 4 (1 cement : 4 coarse sand) 2 half brick masonry in superstructure , above plinth level upto floor vlevelusing bricks of designation 75 cement mortar 1 : 4 (1 cement : 4 coarse sand) 3 dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead:of area exceeding 3 square meter. 4 dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead:for thickness of tiles 25mm to 40mm. 5 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. 6 dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. 7 demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge:in cement mortar. 8 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.all kinds of soils 9 repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead with cement mortar 1 :4 ( 1 cement : 4 coarse sand) 10 repair to stone masonary in cement sand mortar 1:6 with old and new stone. 11 grinding of existing floor with60, 80, 120 and360 no. carborundum stoneincluding cost of wax polishing complete : 12 add extra for mirror polishing on existing marble work/ kota stone flooring work where ever required to give high gloss finish complete. 13 providing and fixing double scaffolding system on the exterior side, upto five story made with 4 wooden member 1.5 m c/c horizontal and vertical direction joining with rassi, clamps, challies. the scaffolding system shall be stiffened with bracing, runner, connection of building if necessary with all essential safty features for the workmen etc complete as per direction of ei.the lavation area of the scaffolding shall be measured for payment. the payment will be made once irrespective of duration of scaffolding.note : this item to be used for maintence work judically 14 repair of existing steel glazed doors, windows and ventilator, ms sheet door, garge doors, compound wall gates etc. by welding drilling complete include. cost of welding rods and hire charge of welding meachine and tp etc complete 15 repair to damaged rcc slabs, beams and columns etc for strengtheing with cement mortar 1 : 2 in following stepsi) choping losse and cracked concrete to required depth, cleaning the exposed surface of steel and concrete with wire brush and sand papering , cleaning of concrete surface with water as necessary and getting dried.ii) applying epoxy primer on the exposed steel bars.iii) applying epoxy hardener and resin mix (as per manufectured s specification) on concrete and steel bars with brush.iv)speading dry cement mortar 1 : 2 mix over epoxy treated wet surface and allow it to dry for one day.v) plastering the surface with cement sand mortar 1 : 3 upto depth of 30mm complete.vi) cure the plastered surface for 15 days all work including scaffolding etc. complete in all respect. 16 making the opening inmasonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground.for door/windows/clerestory windows 17 replacement of stone chajja with sriwan in damaged portion as per existing thickness and width in cm 1 : 3 with removal of old damaged pieces of chajja including top plaster of chajja and bottom pointing in cm 1 : 3 with scoffolding upto ground floor level as per direction of engineer in charge 18 add extra for each additional floor 19 repair to damaged cement plaster of stone chajja with cm 1 : 3 of required thickness on top &bottom as per existing pattern and making patta etc complete up to three floor level as per direction of engineer in charge including all necessary scoffolding etc 20 making of holein r.c.c. slab/wall/beams and masonary wall (width up to 450 mm) by core cutting machine complete as per direction of eidiameter above 150mm 21 supplying and fixing in walls machine cut and polished stone shelves, tands andin cm 1:3 with machine cut edges :sand or other approved stone 50mm thick. 22 providing and fixing marble stone flooring table rubbed, 15 18 mm thick over 20mm (av.) thick base of cm 1:4 (1 cement : 4 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. or providing and fixing stone slabs table rubbed, 15 18 mm thick in walls, steps, pillars, counters, jambs, shelves, sills etc. laid on 12mm (av.) thick base of cm 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. makranaadanga .above 3601 cm2 slabs 23 providing and fixing marble stone flooring table rubbed, 15 18 mm thick over 20mm (av.) thick base of cm 1:4 (1 cement : 4 coarse sand) jointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. or providing and fixing stone slabs table rubbed, 15 18 mm thick in walls, steps, pillars, counters, jambs, shelves, sills etc. laid on 12mm (av.) thick base of cm 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.keseriaji/ abu ambaji (green marble)above 3601 cm2 slabs 24 providing and fixing granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12mm (av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.jhunjhunu / jalore (red/choclate/black/pink colour)above 3601 cm2 slabs 25 extra for providing edge moulding to 15 18mm thick marble/ granite/kota stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. marble workfull edge moulding 26 extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/granite/stone workincluding necessaryholesfor pillar taps etc. including rubbing and polishing of cut edges etc. complete 27 providing and fixing 1st quality mat finished ceremic tile size 300x300mm confirmingto is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). 28 extraforusingmarbleprinted/graniteshadeordarkshadetilesinsteadofwhite,grey,ivory,fumeredbrown,lightgreen,lightblueandotherlightshadesinandmatfinishedtiles. 29 extraforusing 400mm x 400mm mat finishedtiles in place of 300mm x 300mm size. 30 add extra for fixing glazed/ ceramic/ vitrified floor tiles with cement based high polymer modified quick set tile adhesive (water based) conforming to is: 15477 , using 5kg. adhesive per sqm of tile area, in average 3mmthickness instead of cement mortar. 31 p & f 1st qualityheavy duty vitrified polished digital tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to is 15622 of approved make in all colour and shade, laid with 20 mm thick cm 1: 4 including grounting the joints with white cement and matching pigment etc complete.size 600mm x 600mm 32 extra for providing edge moulding to 15 18mm thick marble/ granite/kota stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. granite/kota stone workfull edge moulding 33 extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete 34 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1 cement : 6 sand). 35 supplying and fixing stone lintels/bed plates of approvedquarryroughdressedincement mortar 1:4 :upto 15 cm. thick. 36 stone work (machine cut edges) for wall cladding/ veneering work up to 10 m heightwith 20 to 30 mm thick pink sand stone (bansi paharpur) and backing filled with a grout of 12mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (to be secured to the backing by means of cramps which shall be paid separately)exposed face machine cut 37 plaster on new surface on walls in cement sand mortar 1:4 including rackingofjointsetc. complete fine finish :25 mm thick. 38 kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand)for area of each slab from 2001 to 5000 sq.cm 39 providing and fixing designer cement concrete polished tiles over 20mm average thick base of cm 1 :4 (1 cement : 4 sand) jointing with cement mortar 1 :2 ( 1cement : 2 sand) with pigment to match the shade of the tiles complete with all respect.( as per is 1237:2012) 40 providing and fixing in cm 1 : 4 double paitam (rebated) stone door window and ventilator frames of approved quarry :size 125 x 100mm 41 providing and laying water proofing treatment in sunken portion of wcs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proffing cement compound @0.253 kg//sqm .this layer will be allowed to air cure for 4 hours.b) second layer of slurryof cement @ 0.242 kg/sqm mixed with water proffing cement compound @ 0.126 kg/sqm this layer will be allowed to air cure for4 hours followed by water curing for 48 hours.the rates includes preparation of surface treatment & sealing of all joints ,corners,junction with polymer mixed slurry. 42 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 43 extra if square,rectangular hollow tubelarsections are used or grill made by flats onlyover item no 9.8.1 44 carriage of material building rubbish stone metal (grit and ballast etc.)including loading and unloadingfor 20 km. 45 grading roof for water proofing treatment withwater proffing compoundcement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 46 providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 47 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m15 grade nominal mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size). 48 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). ...

Rajasthan State Agricultural Marketing Board - Rajasthan

32582101 various yard works ( 2 nos. ) / kums sri ganganagar ( fandv ) package 01 / 2022 23 / sgnr / development / provision of various facilities in mandi yard kums sri ganganagar (f&v) 2 part a (civil work) 3 demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer in charge : 1: 3: 6 or richer mix. 4 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge : in cement mortar 5 removing mortar from bricks and cleaning bricks including stacking within a lead of 50 meters (stacks of cleaned bricks shall be measured) : from brick work in cement mortar. 6 disposal of earth, sand, gravel, u/s kankar, lime, flyash, morrum, manure or sludge up to 5000 mtr. beyond ist 50 mtr. lead (including loading and unloading) 7 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. 8 demolishing mud phuska/ lime dhar/ kharanjain terracing and disposal of unserviceable material within 50 meters lead. 9 dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. 10 repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead : with cement mortar 1 :4 ( 1 cement : 4 coarse sand) 11 dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead : of area 3 square meter and below. 12 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter : all kinds of soils 13 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 14 a) m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 15 c) m20 grade nominal mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size). 16 brick work with common burnt clay f.p.s.(non modular) bricks of class designation 7.5 infoundation and plinth with : cement mortar 1 : 6 (1 cement : 6 coarse sand) 17 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. : m20 grade nominal mix /design mix 18 centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 19 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc : m20 grade nominal mix / design mix 20 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 21 brick work with common burnt clay f.p.s.(non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor five level in all shapes and sizes in : cement mortar 1 : 6 (1 cement : 6 coarse sand) 22 honeycombbrickworkhalfbrickthickwithcommon burnt clay f.p.s.(non modular) bricksofclassdesignation7.5uptofloor five level in : cement mortar 1 : 4 (1 cement : 4 coarse sand) 23 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level : cold twisted deformed bars (is : 1786). 24 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 25 plaster on new surface on wall in cement sand mortar 1:6 including racking of joints etc. complete fine finish : 26 a) 20mm thick 27 b) 12mm thick 28 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3 fine sand) 29 grading roof for water proofing treatment withwater proffing compound : cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 30 providing and fixing 20 mm thick precast terrazo tiles of approved make, with marble chips of size upto 6mm laid over roof with neat cement slurry mixed with pigment to match the shade of the tiles, including cutting ,grinding rubbing with machinecomplete on 20 mm thick bed of cement sand mortar 1 : 4. 31 kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : for area of each slab from 901 to 2000 sq.cm. 32 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 300mm x 450mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 33 painting with synthetic enamel paint of approved brand and manufacture togive an even shade : two or more coats on new work 34 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 35 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. 36 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect : on new work 37 providing&layingpopcorniceofrequireddesign&patterninceilingincludingnailing&scafolldingetc.completewithfinefinishing of size : 50mm x 50mm. 38 providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 39 supplying and fixing rolling shutters of approved make, made of 80 x 1.25mm. m.s. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including cost of spring hooks, providing and fixing necessary 27.5cm. long wire springs grade no. 2 and m.s. top cover 1.25mm thick for rolling shutters as per design. (clear openable area to be measured for payment). 40 providing and fixing m.s. sheet 1mm thicksingle leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of engg. incharge but excluding cost of chowkhats: including two coats of anit corrosive red oxide primer paint 41 providing & fixing fly proof wire gauze to windows, clerestorywindows & doors with m.s. flat 15x3 mm and nuts & bolts complete : galvanised m.s. wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides 42 providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required : partly fixed and partly openable (fixed area not to exceed 33%) 43 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592including jointing with seal ring conforming to is : 5382 leaving 10 mm gap for thermal expansion.(i) single socketed pipes : type b, 110 mm diameter. 44 providing and fixing on wall face unplasticised pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a including jointing with seal ring conforming to is : 5382 leaving 10 mm gap for thermal expansion : single bend w/o door 87.5 deg. : 110mm dia 45 providing and fixing granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12mm (av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete : south (red/cholate colour) : 1501 cm2 to 3600 cm2 tiles. 46 p & f wvc wash basin (ist quality is:2556 mark) of approved make with c.i. brackets duly painted 1 no. 15 mm c.p. pillar cock (is:8934 mark) & 32 mm c.p. brass waste coupling of approved make 32 mmwaste pipe complete including cutting & making good the wall : size 550 mm x 400 mm dia for counter top 47 p & f lst quality wvc urinal (is:2556 mark) with 25mm dia g.i. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete : wvc flat back half stall urinal size 580x380x350 mm/ angle back 450x375x350 type liped front. 48 providing and fixing stainless steel a isi 304 (18/8) kitchen sink & is 13983 with c.i. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : stainless steel kitchen sink without drain board 470x420mm bowl depth 178 mm 49 p & f g.i. pipeswith g.i. fittings (is:1239 mark) & m.s. clamps including cutting and making good the walls and floors : (internal work ) medium duty pipes : internal work : 50 a) exposed on walli) 15 mm dia nominal bore 51 ii) 20 mm dia nominal bore 52 p & f bib cock (is : 8931 mark), superior quality of approved make : c. p. brass long body, 15mm nominal bore weight not less than 690 gm 53 p & f stop cock(is :8931 mark),superior quality & ofapproved make: 54 a) c.p. brass 15mm nominal bore. 55 b) cp brass concealed stop cock 15mm. 56 p & f inlet connection (angle valves) superior quality, of approved make, for wash basin, gyser etc. : c.p. inlet connection 15 mm brass (is:8931 marked). 57 p & f pvc storage tank (is:12701 marked indicating the bis license no.) of approved make with cover, 25 mm dia 1 m long g.i. over flow pipe & 25 cm. long wash out pipe with plug & socket, including placing on terrace( at all floors),making connection etc. complete of approved design. details of cost for 500 litre 58 construction of open surfacedrain with 112mm thick brick masonry in cm 1:4,110mm thick base concrete 1:5:10, 37mm thick m 15 grade c.c. flooring ,12mm 1:4 cement plaster on all exposed faces of walls including top surface excavation & disposal of earth complete as per approved design/drawing : 150mm drain,225mm av. depth. 59 part b electric work 60 wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694)and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694)in recessed isi markedmms ( is:9537 p iii ) vergin material pvc conduit & its all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required.for specification of copperconductor,phenolic laminated sheets & electrical/ wiring accessoriesrefer chapter e 04, e 05 & e 07 . for additional technical parameters of products/ work, referannexure a attached with this bsr . 61 (a) short point (up to 3 mtr.) 62 (b) medium point (up to 6 mtr.) 63 (c) long point (up to 10 mtr.) 64 wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694)and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694)in recessed isi markedmms ( is:9537 p iii ) vergin material pvc conduit & its all accessories( j.b. , bends etc.) , round tiles, 18 swg hot dipped galvanized modular box with earth terminal, 6 a modularswitch, 3/ 5 pin 6 a modular socket, modular face plate with grid plate, screws etc,all as per pre approved by engineer in charge,making connections, testing etc. complete as required.for specification of copperconductor,phenolic laminated sheets & electrical/ wiring accessoriesrefer chapter e 04, e 05 & e 07.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 65 (a) on board 66 (b) medium point (upto 6 mtr.) 67 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.99% purity copper, class 5 stranding in acc. to iec 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4,, in existingsurface or recessed pvc/ ms conduit/casing capping includingall as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work, referannexure a attached with this bsr . 68 (a) 2 x 2.5 sqmm + 1 x 1.5 sqmm 69 (b) 2 x 4 sqmm + 1 x 2.5 sqmm 70 providing & fixing of 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c tripping characteristic as per type of load andsite requirement) 4kv impulse withstand voltage,as per pwd specification for electrical works with isi marked is 8828(1996) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec,minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 71 contact protection and fitted withexisting distribution board/sheets, min. operation 20,000 upto 32 a rating and 10,000 upto 63 a, 5000 for 80 a ratingincluding making connections, testing etc. as required.. oem shall have submitnabl / cpri / erda accrediated lab test reportsbefore execution & all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr.(a) single pole mcb6 a to 32 a rating 72 providing & fixing of 240/415 v isolator as per pwd specification for electrical works with isi marked is:13947 iii/conforming to iec 60947 3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage,true contact indication,red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheetincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab test reportsbefore execution & all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : double pole isolator : a) 63 a rating 73 providing & fixing of ik09 recessed/surface mounting heavy duty horizontal type sheet steel of 1.6 mm thickdistribution board as per pwd specificationfor electrical works isi marked conforming to is 13032 & is 8623 / conforming to iec 61439 3. phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal dbterminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.oem shall have submitnabl / cpri / erda accrediated lab test reportsbefore execution & all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : ip 43 double door (single phase) : (a) 6 way (6 o/g + 2 i/c) 74 s&f following sizes (dia.) of isi marked mms ( is:9537 p iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as requiredinrecess includingcutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work, referannexure a attached with this bsr : mms (is : 9537 p iii) pvc conduit : 25 mm. 75 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un armoured / armouredaluminiumcable of 1.1 kv grade as per pwd specification for electrical worksin existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench with filling of excavated earth in trench, on existing cable trays or on surface etc.including making necessary connection, testing etc. as required of size andas per points (a), (b), (c), mentioned below: 76 (a) material : h4 gradealuminium conductor of purity >99.6 %& as peris:1554 p i / is :7098 p i 77 (b) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures . 78 (c)oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities forcables . appropriate type test certificate / oem test report shall be submitted .all above as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : i) un armoured : a) 10 sqmm 2.0 core 79 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coatedhousing with in built driver, power consumption of18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k/ 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. 80 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsr.a) 4 led tube shape fixture 18/20 w (polycarbonate base) 81 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 18 swg with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch (is :3854) and 3/5 pin 16 amp. socket outlet (is:1293) [ as per detailed in respective item in bsr] , making connection , testing , etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 82 supply installation testing & commissioning of iso certified manufacturer mademonoblock motor pump set isi marked (is:9079 2002) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008,& is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single/three phase ( 240 440 v ) permanent split capacitor type (psc), fitted with thermal overload protection, . including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. appropriate type test certificate / oem test report shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : 0.5 hp, 1 ø, (3 18)mtr, (100 26) lpm 83 providing & fixing ofof m.s. j hook of standard design made out of 16 mm dia. m.s. round bar and fixed withcement concrete mortar with required support as required. 84 providing & fixing of modular type step fan regulator duly isi marked (is :11037) as per pwd specification for electrical works,made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , minimum width of 1 module switch toggle( push part ) should not less then 20mm,includingall as per pre approved by engineer in charge,making connections, testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : 5 step fan regulator 100 watt 2 module 85 providing & fixing of following modular accessories as per pwd specification for electrical works,made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , minimum width of 1 module switch toggle( push part ) should not less then 20mm,includingall as per pre approved by engineer in charge,making connections, testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : blanking plate. 86 widening & upgradation of gate no. 01 & 02 with check post at kums sri ganganagar (f&v) 87 part a (civil work) 88 demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer in charge : 1: 3: 6 or richer mix. 89 demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge : in cement mortar 90 removing mortar from bricks and cleaning bricks including stacking within a lead of 50 meters (stacks of cleaned bricks shall be measured) : from brick work in cement mortar. 91 disposal of earth, sand, gravel, u/s kankar, lime, flyash, morrum, manure or sludge up to 5000 mtr. beyond ist 50 mtr. lead (including loading and unloading) 92 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. 93 demolishing mud phuska/ lime dhar/ kharanjain terracing and disposal of unserviceable material within 50 meters lead. 94 dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. 95 repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead : with cement mortar 1 :4 ( 1 cement : 4 coarse sand) 96 dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead : of area 3 square meter and below. 97 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter : all kinds of soils 98 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 99 a) m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 100 c) m20 grade nominal mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size). 101 brick work with common burnt clay f.p.s.(non modular) bricks of class designation 7.5 infoundation and plinth with : cement mortar 1 : 6 (1 cement : 6 coarse sand) 102 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. : m20 grade nominal mix /design mix 103 centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 104 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc : m20 grade nominal mix / design mix 105 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. : m20 grade nominal mix / design mix 106 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 107 brick work with common burnt clay f.p.s.(non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor five level in all shapes and sizes in : cement mortar 1 : 6 (1 cement : 6 coarse sand) 108 honeycombbrickworkhalfbrickthickwithcommon burnt clay f.p.s.(non modular) bricksofclassdesignation7.5uptofloor five level in : cement mortar 1 : 4 (1 cement : 4 coarse sand) 109 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level : cold twisted deformed bars (is : 1786). 110 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 111 plaster on new surface on wall in cement sand mortar 1:6 including racking of joints etc. complete fine finish : 112 a) 20mm thick 113 b) 12mm thick 114 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3 fine sand) 115 grading roof for water proofing treatment withwater proffing compound : cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 116 providing and fixing 20 mm thick precast terrazo tiles of approved make, with marble chips of size upto 6mm laid over roof with neat cement slurry mixed with pigment to match the shade of the tiles, including cutting ,grinding rubbing with machinecomplete on 20 mm thick bed of cement sand mortar 1 : 4. 117 kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : for area of each slab from 901 to 2000 sq.cm. 118 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 300mm x 450mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 119 direction and place identification signs with size more than 0.9 sqm size board. (providing anderecting direction and place identification retro reflectorised sign asper irc: 67 made of ncasulated lens type reflective sheeting vide clause801.3fixed over aluminium sheeting ,2mm thick with area exceding 0.9 sqm supported on a mild steel angle iron post 75mm x75mm x6mm ,2 nos . firmly fixed to the ground by means of properly designed foundation with m 15 grade cement concrete45cm x 45 cm x 60 cm , 120 painting with synthetic enamel paint of approved brand and manufacture togive an even shade : two or more coats on new work 121 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 122 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: two or more coats on new work including prepartion of base with primer, putty, lippy etc complete in all respect. 123 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect : on new work 124 providing&layingpopcorniceofrequireddesign&patterninceilingincludingnailing&scafolldingetc.completewithfinefinishing of size : 50mm x 50mm. 125 providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 126 providing and fixingaluminum workfor doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285,fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required pvc/neoprene felt etc. aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing /paneling , c.p. brass/ stainless steel screws al. tower bolt & al. handle & al. aldrop etc.,all complete as per architectural drawings and thedirections of engineer in – charge .(glazing and paneling to be paid for separately). 127 a) for fixed portion : anodised aluminum (anodised transparent 81 dyed to required shade according to is : 1868. (minimum anodic coating of grade ac 15, anodizing to be got done from approved anodizer) 128 b) for shutters builtup standard tubular sections of openable doors , windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately) : anodised aluminum (anodised transparent 81 dyed to required shade according to is : 1868. (minimum anodic coating of grade ac 15, anodizing to be got done from approved anodizer) 129 providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with pvs / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge.(cost of aluminium snap beading shall be paid in basicitem.) : with float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) 130 providing and fixing double action hydraulic floor spring of approved brand and manufacture is : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece m.s. : with stainless steel cover plate 131 providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. 132 providing and fixing of double leaf steel shutterfor cupboard, the frame is made of pressed steelisi section 80x25 mmx1.25 mm thickwith 1.00 mm ms sheet to spot welded including holdfasts of 15x3mm, ms oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc completeincluding applying priming coat of approved steel primer of red oxide zinc chromate andspray painting in approved shade with deco paint of approved quality complete as per direction of engineer in charge 133 providing and fixing of reinforced ferro cement drain covers designed for a & aa class loading duly marked on cover with adequate steel reinforcement having thickness 75mm to 150mm anti corrosive bitumen painted m.s. plate, rim and m.s. lifting hooks, admixtures like plasticizer, bond improving compound, shrinkage, resistance compound, abrasion resistant complete as per approved design etc. : for class aa loading : span 300 to 450mm standard size 600x800mm 134 providing and fixing expanded grill made of aluminum as per design and drawing having members section of size 7.5mm x 6.0mm and opening of size 102mm x 99mm to aluminum window/vent with required screws, y and h aluminium sec (as per drawing) at the ends and middle joints respectively complete in all respect as per direction of engineer in charge : anodised aluminum (anodised transparent 81 dyed to required shade according to is : 1868. (minimum anodic coating of grade ac 15, anodizing to be got done from approved anodizer). 135 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592including jointing with seal ring conforming to is : 5382 leaving 10 mm gap for thermal expansion.(i) single socketed pipes : type b, 110 mm diameter. 136 providing and fixing on wall face unplasticised pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a including jointing with seal ring conforming to is : 5382 leaving 10 mm gap for thermal expansion : single bend w/o door 87.5 deg. : 110mm dia 137 providing and fixing granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12mm (av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete : south (red/cholate colour) : 1501 cm2 to 3600 cm2 tiles. 138 providing and fixing clamps of required size & shape in rcc/ cc backing with cement mortar 1:2 ( 1 cement :2 coarse sand) including drilling necessary hole in stones and embedding the cramp in the hole : stainless steel cramps. 139 p & f wvc wash basin (ist quality is:2556 mark) of approved make with c.i. brackets duly painted 1 no. 15 mm c.p. pillar cock (is:8934 mark) & 32 mm c.p. brass waste coupling of approved make 32 mmwaste pipe complete including cutting & making good the wall : size 450mm x 300mm : size 550 mm x 400 mm dia for counter top 140 p & f lst quality wvc urinal (is:2556 mark) with 25mm dia g.i. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete : wvc flat back half stall urinal size 580x380x350 mm/ angle back 450x375x350 type liped front. 141 p & f g.i. pipeswith g.i. fittings (is:1239 mark) & m.s. clamps including cutting and making good the walls and floors : (internal work ) medium duty pipes : internal work : 142 a) exposed on walli) 15 mm dia nominal bore 143 ii) 20 mm dia nominal bore 144 p & f bib cock (is : 8931 mark), superior quality of approved make : c. p. brass long body, 15mm nominal bore weight not less than 690 gm. 145 p & f stop cock(is :8931 mark),superior quality & ofapproved make: 146 a) c.p. brass 15mm nominal bore. 147 b) cp brass concealed stop cock 15mm. 148 p & f inlet connection (angle valves) superior quality, of approved make, for wash basin, gyser etc. : c.p. inlet connection 15 mm brass (is:8931 marked). 149 p & f pvc storage tank (is:12701 marked indicating the bis license no.) of approved make with cover, 25 mm dia 1 m long g.i. over flow pipe & 25 cm. long wash out pipe with plug & socket, including placing on terrace( at all floors),making connection etc. complete of approved design. details of cost for 500 litre 150 construction of open surfacedrain with 112mm thick brick masonry in cm 1:4,110mm thick base concrete 1:5:10, 37mm thick m 15 grade c.c. flooring ,12mm 1:4 cement plaster on all exposed faces of walls including top surface excavation & disposal of earth complete as per approved design/drawing : 150mm drain,225mm av. depth. 151 part b electric work 152 wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694)and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694)in recessed isi markedmms ( is:9537 p iii ) vergin material pvc conduit & its all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required.for specification of copperconductor,phenolic laminated sheets & electrical/ wiring accessoriesrefer chapter e 04, e 05 & e 07 . for additional technical parameters of products/ work, referannexure a attached with this bsr . 153 (a) short point (up to 3 mtr.) 154 (b) medium point (up to 6 mtr.) 155 (c) long point (up to 10 mtr.) 156 wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694)and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694)in recessed isi markedmms ( is:9537 p iii ) vergin material pvc conduit & its all accessories( j.b. , bends etc.) , round tiles, 18 swg hot dipped galvanized modular box with earth terminal, 6 a modularswitch, 3/ 5 pin 6 a modular socket, modular face plate with grid plate, screws etc,all as per pre approved by engineer in charge,making connections, testing etc. complete as required.for specification of copperconductor,phenolic laminated sheets & electrical/ wiring accessoriesrefer chapter e 04, e 05 & e 07.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 157 (a) on board 158 (b) medium point (upto 6 mtr.) 159 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.99% purity copper, class 5 stranding in acc. to iec 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4,, in existingsurface or recessed pvc/ ms conduit/casing capping includingall as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work, referannexure a attached with this bsr . 160 (a) 2 x 2.5 sqmm + 1 x 1.5 sqmm 161 (b) 2 x 4 sqmm + 1 x 2.5 sqmm 162 providing & fixing of 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c tripping characteristic as per type of load andsite requirement) 4kv impulse withstand voltage,as per pwd specification for electrical works with isi marked is 8828(1996) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec,minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted withexisting 163 distribution board/sheets, min. operation 20,000 upto 32 a rating and 10,000 upto 63 a, 5000 for 80 a ratingincluding making connections, testing etc. as required.. oem shall have submitnabl / cpri / erda accrediated lab test reportsbefore execution & all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr.(a) single pole mcb6 a to 32 a rating 164 providing & fixing of 240/415 v isolator as per pwd specification for electrical works with isi marked is:13947 iii/conforming to iec 60947 3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage,true contact indication,red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheetincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab test reportsbefore execution & all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : double pole isolator : a) 63 a rating 165 providing & fixing of ik09 recessed/surface mounting heavy duty horizontal type sheet steel of 1.6 mm thickdistribution board as per pwd specificationfor electrical works isi marked conforming to is 13032 & is 8623 / conforming to iec 61439 3. phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal dbterminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.oem shall have submitnabl / cpri / erda accrediated lab test reportsbefore execution & all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : ip 43 double door (single phase) : (a) 6 way (6 o/g + 2 i/c) 166 s&f following sizes (dia.) of isi marked mms ( is:9537 p iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as requiredinrecess includingcutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work, referannexure a attached with this bsr : mms (is : 9537 p iii) pvc conduit : 25 mm 167 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un armoured / armouredaluminiumcable of 1.1 kv grade as per pwd specification for electrical worksin existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench with filling of excavated earth in trench, on existing cable trays or on surface etc.including making necessary connection, testing etc. as required of size andas per points (a), (b), (c), mentioned below: 168 (a) material : h4 gradealuminium conductor of purity >99.6 %& as peris:1554 p i / is :7098 p i 169 (b) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures . 170 (c)oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities forcables . appropriate type test certificate / oem test report shall be submitted .all above as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : i) un armoured : a) 10 sqmm 2.0 core 171 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coatedhousing with in built driver, power consumption of18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k/ 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing. 172 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsr.a) 4 led tube shape fixture 18/20 w (polycarbonate base) 173 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 18 swg with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch (is :3854) and 3/5 pin 16 amp. socket outlet (is:1293) [ as per detailed in respective item in bsr] , making connection , testing , etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 174 providing & fixing of iso certified company made beestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanas per pwd specification for electrical works, conforming to is:374 2019, & is:1885 p v 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required.appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : 1200 mm sweep bee 3 star rated (service value >=5.0 to< 5.5 ) 175 providing & fixing ofof m.s. j hook of standard design made out of 16 mm dia. m.s. round bar and fixed withcement concrete mortar with required support as required. 176 providing & fixing of modular type step fan regulator duly isi marked (is :11037) as per pwd specification for electrical works,made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , minimum width of 1 module switch toggle( push part ) should not less then 20mm,includingall as per pre approved by engineer in charge,making connections, testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : 5 step fan regulator 100 watt 2 module 177 providing & fixing of following modular accessories as per pwd specification for electrical works,made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , minimum width of 1 module switch toggle( push part ) should not less then 20mm,includingall as per pre approved by engineer in charge,making connections, testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : blanking plate. 178 providing & fixing of ip40 led recessed / surface mounted, round / sqaure non dimmable back lit smd mid power led downlight with die cast aluminum housing & heat sink for heat dissipation with uv stabilized non yellowish diffuser with internal/ external bis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% and in compliance to iec standards. system lumen efficacy of = 120 lm / watt, thd < 10 % ,p.f.=0.95, cri >80,life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k/ 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing onhousing. 179 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsr. : recessed mounting : led downlight 18/20w 180 providing & fixing of ik07 ip 66 protected led street light luminaire on existing bracket/pole. fixture made of powder coated single piece pressure die cast aluminum lm6/ adc12 material with heat dissipation fins on housing with uv stabilized pc/toughened glass cover (uv stablzation report submitted for uv cover ) and secondary lens on each led & should be smd type . the system level luminaire efficacy >=120 lm/ wtwith high power leds is to be usedand potted driver must be potted & has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety ,input frequency 50hz±3% power factor >0.95 driverefficiency >85%,thd(i) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <1000ma shown in lm79 report. the luminaireshall be bis certified and t.c. certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened ,color 181 rendering index >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark/name engraved/embossing on die cast housing to allow traceability/authenticity. fixture shall be as per is 10322 complianced. oem must have its own in house nabl lab setup for all testing facilities forled fixtures.(lm79/lm80) certificate/ report with liable warranty of product/accessories from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr : led street light fixture 60 watt ...

North Western Railway - Rajasthan

32400309 auction sale of scrap u / s aol stationary bed plate steel mounted dc arc welding set fitted with electric motor. location: opp. acid godown....

Department Of Training And Technical Education - Rajasthan

32267828 supply of electrician trade tools and equipments measuring steel tape combination plier insulated 200 rrm ( 40 +2 ) nos. screr.r, driver lnsulated :lmnr x i 5c rnrr. i ) iamond head ( 40 +2 ) nos. 4. screr.vdriver insulated 6mm x 150 rnm ( 40 +2 ) nos. 5. electrician screwdriver thin stem insu lated hand le zlmm x 100 mm ( 10 +2 ) nos. 6. heavv duty screwdriver insu iated 5nrnr x 200 rnm ( 40 +2 ) nos7. h lectrician screwdriver thin stem insu lated hand le 4mnr x 250 rrnr ( 40 +2 ) nos8. punch flentre 9mrr x 150 mnr ( 40 +2 ) nos. 9. knife double bladed electrician i00 mm ( 40 +2 ) nos. 10. neon tester 500 v ( 40 +2 ) nos. lt steel rule graduated both in metric and english lrnit 300 innr u, ith precision of ii4ii, mm ( 40 +2 ) nos. t2. hammer, cross peen with handle 250 glams ( 40 +2 ) nos. b. shop tools & equipment fot 2 1+1 ) units no additional items are required li ) list of tools & accessories 13. hammer. ball peen with handle 500 granrs .i n os. 14. pincer 50 rrrr 4 nos. 15. c clamp 200 nrm and l0 ( ) rnrr 2 nos. each 16. spanner adjustable drop forged, ss 50 mrr & ioomnr 2 nos. each , l ) ] , .., ...; 11, , , , , r blou larnp brass ( lhisel cold 25 nrnr x 100 nlnl chisel tirmer r, ith wooden handle 6 mm x 200 ntnr allen key alloy steel l. 5 l0 mm ( setof 9 ) 0.5 ltr. capacity pull ) puller with 3 legs i 150 nrm & 300nrnr bearing puller linside and otttsjde t scissors blade. ss 150 rrnt 1.5 sq nrtr to 16 sq trtn crinrping lool 16 jq rrlrll to 95 sq rnm wire cutter and stripper iiil rn mallet hard wood 0.ril lill halnmer extractor type 250 grarns hacksaw tranre radjustable l00nrrr fixed 150 2 nos. each try square ll50 nrrl blade outside calliper ., il ] nt .p, inr.t t pd inside calliper i: r sorirts tr oe l 5l rrn spring i pe plicrs long nose insulated 15i rnrn 1 nos. pliers 4 n os llat nose insulated pliers round nose insulated l0ll nm treezers l5c mrn i 4 nos. snip straight and bent heavldut5 250 nirt d.e. metric spanner double ended 6 12 nrrn drill hand brace 0 l00rnm 1 nos. drill s.s. lwist block 2 nrm.5 ntnr and 6 rnrn set of 3 50 nm x 200mm 50 nrnr x 20 { ) mbl gauge. wire imperial stainlees steel wire ( ) atrgl metric maked in swg & mnr l0l ) rrnr lnd cut uilh handle { l nos. file half round l0l rrn lnd cut rvith handle i 4 nos. file round 20ll rn1 llnd cut r, ith handle file llat rough i : ( l lrn . iih handle .1 os. lil ir, irl u ith hrndle file flat smooth l: ir , rlx ith lirndlc file rasp, half round 20il !r1nr bastard rvith handle coppet bit soldering iron. 0.15 kg i leat ;rlor:rl nrrzzle. pvc type. 25itlrrrr 4 nos. de soldering gun plane cutters smoothing cutter file flat , file flat bastard grease gun bradawl pipe vice cast iron with hardened jaw open scissor blade 57. hand vice 50 mm jav, , l nos. 58. table vice 100 mm.jau, t lros. 59. oil can 250 ml i l, jos. 60 contactor & auxiliary contacts 3 phase. 415 vola. 25 amp u.ith 2 nos. each 2noandlnc 6t contactor & auxiliary contacts. 3 phasc. 4 1 5 volt. 32 anrp u, ith 2 l. os. each 2noand2nc 62. limit switch limit switch. l iver opetated 24 i nos. 500v 2 contacts 61, rotary switch 16 r i.140 i nos. 64. relay a. cut out relays b. reverse current c. over current d. [ jnder voltase a. 164. 1.10 i l.jo. each b. r6, 4. 440v c. 16a.4 10v d.360v 440v 65. pin type. shackle type, egg l, pe & suspension type insulators incjuding hardware fittin { r i nos. each 66. llydrometer i nl, s. 61. hand drill machine 0 6 rrrrrr c.rpel it1 i os. 68. portable electric drill machine 0 i2 mrr capacit ) 750rv.2, 10v i no. with chuck and ker 69. load bank ( larnp / heater t pe ) 6 k , . iph r no. 70. brake test arrangement with tu, o sorine balance ratinp 0 ro s ko i , .r. 71 laboratory t ) pe induction coil 1000 w i nos. 72. orrf side micrometer 0 25 nrm least counl 0.01mm 2 nos. 13. thermorneter digital 0c 150 c i no. 14. series test lamp 230v.60w , 1nos. 75. knife switch dpdt fitted with fuse terminals l6 arrp rtr nos. 16 knife switch tpdt fitted with fuse terminals l6 amp / 440 v 4 nos. 77. miniature breaker 16 amp i nos. eadh plate 60cm x 60cm x 3. i5mm copper plate 60cm x 60cru x 6mm gi plate leach 79. earth electrode primary electrode 2 i 00x28x3.25mm secondaq, cu strid 20x5mrn i no. 80. mccb l00a, nps. triple pole i no. 8r. fi.cb and rccb 25arrrps. double pole and 2 5r mps. double pole ian i0 ma i each fuses hrc glass re*ire t1 pe .1 f.ach 83. rheostat ( sliding type ) 0 0 25 ohm. 2 amp 300 ohm. 2 amp i ohm. 10amp l0 ohrn. 5 arnd 0 0 i no. each 84. capacitors various electronic component various lamps rubber mat plug socket piano switch lanrp holder llr v. i a cab les: twisted paii non metal lic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multiconductor cable coaxial cable bus bar rvith brackets irrir cacl l 2x4x l electrician helmet yellorv colour rcc pole with accessories ( ms angle iron.cclamp, stal insulaior etc.t o ill and material. safety belt stanclald qualitl l 2 nos. list of eouidment ohm meter; series type & shunt 5012000 ohrn analog 2 nos. each tvne ooftable box digital multi meter a.c. voltmeter m.l. analog. poftable box type housed in bakelite case illlrlti range 75 v i50v rrl0 600v milli voltmeter centre zero analog. poftable box type housed in bakelite case i00 0 100 mv arrmeter mc analog. pofiable 0 i0 ( ) ria. 0 5 a. 0 25 a box type housed in bakelite case 2l os. each ac ammeter ml. analog. 0 i a. 0 5 a 0 25 a 2 nos. each porrable bor type housed in bakelite case kilo wattmeter analog name of the tools and specification 0 1.5 ikw. pressure coil raring 1.101 r i.10v, current iat ing lia / i 0aanaloge. porrabie t1, pe housecl in llaiiclite case 2 nos. i i digital wattmeter a.c. energy meter a c e*.gy m.t* poner factor meter digital f =, f*r. ) , m.t.t isingte phase. j 0 .l.. 240v l4lilll , vp. .fhrce phase. i 5a ..!40v llqry4ry!. i440v.20a, three pnase portu h le bo tlpe 145 to 5i i l:z f nos. l , ) s. 102. r03. 104. i05. 106. lvagrtetic flur metcr 0 j, , u rc., la : , . __ i u rneler lu.r. n, e ter i ( lj read ( lrrt 0.0 ; _ , rs. , lo 700 ( r lurncns ill . i attcr_v. ] t, ffiejoc ceroooorpm ._ln;__ i t0 { ) c0 rlm tongtester / ctu.pmffi 2 ns : ryanjos 5oov l , i, * 3 point d.c. starter f or 2.5 kw dc r;otoi :. t07. 108. i l 109. i t0. l i 12. i i3. j po int d.c. starrer for 2.5 k l, dc motor j no. i i 4. ] whrt stone bridge r.r ith i galvanotneter and batterv i nos. i 15. single phase variable auto franst ormer cooled ) i 16. phase sequence indicator i phase..ll5 v i nos. 117 . crowler ac starters: a. resistance type slarter b. direct online starter c. star delta starter manual d. star delta stafter semi automatic e. star delta starter fully automatic f. star delta starter soti stafter g. auto transformer type tachometer 9. oscilloscope dual trace 20 mhz i no. 120. function generator 2 to 200 kilz. sine, square triangular 220 v 50 llz. single phase !no. 121 soldering lron temperature controlled soldering l50 , i an. li.l voir discrete component trainer discrete component ( for diode and trarrsislol circuill rr ith 2 itos. regulated pou er !:upplv +5, 5 v.+12.9 12 y linear l.c. lrainer [ . ireal lc. trainer u, ith reglilated pou er slrppll, i .2v i to i5v t } lc socket i6pin and 20 pins with bread boaril ] digital l.c. trainer digital i.c. trainer 7 se, :rren1 d isp lav , and bread board domestic appliances a. 1500 wa11. 2.10v i no. each b. e lectric kerlle b. i 500 ?ttr 2 10 / c. e iectric lron c. automatic 750 . 240 d. immersion heater , d l50f u, a1i. l 10v 126. ie. a.c. ceiling fan and ac c. f, e , .rrr ii0 v table fan 1 . geyser ( storage type ) t. l0 iitrc i g. mixture & grinder h. washing machine serniautomatic i. motor pump set oiltesting kit electric induction plate inverter with battery i kya wirh l2 v barterv lnplrt l2 r, olt dc. outputi no. voltage stabilizer 1ntr vi ac output 110v.i0a dc power supply 0 , 30 v 5 a 12 nos. battery charger i0 potential transformer 4 current transformer i solar panel w ith battery pentium iv computer or latest . ink jet/ laser printer c, shop machinery d.c. shunt generator with control pane motor generator ( ac to dc) d.c. compound cenerator with control panel includ ing fitted rheostat, voltmeter, ammeter and breaker d.c. compound generator rvith control panel includ ing fi tted rheostat.voltmeter. amrneter ancl breaker. 2.5k r. 220v &3pliase squinel cage irrcluction motor. 5l{p. .140v. uith l contlol panel & tar dclta ] starter i 140. dc series motor coupled with spring balance load 2.5 kw. 220 volts i no. 141 dc sh unt motor d.c. compound cenerator with control panel includ ing fitted rheostat, voltmeter, ammeter and breaker d.c. compound generator rvith control panel includ ing fi tted rheostat.voltmeter. amrneter ancl breaker. 2.5k r. 220v &3pliase squinel cage irrcluction motor. 5l{p. .140v. uith l contlol panel & tar dclta ] starter i 140. dc series motor coupled with spring balance load 2.5 kw. 220 volts i no. 141 dc sh unt motordc compound motor u,ith !itarter and sw itch l. j l. :r .::/.) i,l1s i ll 143. motor cenerator(dc to ac) set lshnnt motor rating: 5 hp. consisting of shunt motor with 440v ac generator rating : starling cornpen5ator and su itch j phase. .1 rvi::. :. j kva. directll coupled lo ac generalor 4lr(, ll0 volls. 0.8 pl. with exciter and switch board 50rr ,: i:s mounted with regulator, breaker. ammeter, voltmeter fieq uency meter. knile hlade su itch arrd lure. e1g. set cotnplete r.l ith ca:t irorr bed plate. lixing holts. [oundat ion bolt. arrd llexible coupling. lno. 144. ac squirel cage motor with 5 iip.3 i)hase.4l5v.50 hz star delta starter and triple pole ir,rn clad u itch lirc u ith mrchanical lord. i no. t45. ac phase wound slip ring motor 5 ilp440 v.i phase.s0 hz urith stafier su itch i no. 146. universal motor with 2+,.1 v. 50 t{2. 1 iip i no. stafter/s,,,itch 147 . synchronous motor with 3 l)hase. 3 iip. 4rt[)v. 50h2. ] i no. accessories like starter. ercitation ,1 poie aflangemen t.. 148. thyristor /lgbtcontrolled d.c motor drive with tachogenelator feedback arrangement i ii) lno. 149. thyristor/igbt controlled a.c. vryf uor,!r()l .l ?nase. i i o. motor drive with llp r 50. single phase llansfonrer. corc i kva.240141 5 v. 50 hz 3 nos. t1,pe. ail cooled l5t three phase transformer. shell t1pe oil cooled with delta/ star 3 ri va.,ll 5/2,10 v. 50 hz 2 r os. 152. electrical machine trainer diesel cenerator set with changeover switch. over current hreaker and uater/ air cooled with armature. star deita connections ac 3 phase 7.5 i{va. .i: 5 rar;tg v t,, l ,, hi 1,.,, r. ,. ,. insi tirie 154. ljsed dc generators seriesshunt and compound type lor overhau ling practice i i o ilach 155. pillar e lectric drill machine motorized i 2 ll) rnrr (.:rp:ic rt. i i i ;. r 1l:. 44() ,. 1 phae. irrdrrr l;o h4rtor with d(ll starter. bencir tvde 156. motorised bench grinder i hp. 3 phase. 440v with . o doi starter. ifo,,rhie sidc xi.h sn]oot;i and iougir ni;ee i ,vi1ir iool ilase 157 . a.c. selies type motor i tit 140 .50 ilz , nir i 58. single phase capacitor motor with starter switch i hi.2,10 i0 117 159. manual motor coil winding machine with srep arbor no. 160. ceiling tan coil winding machine 250v. i0 i{7:. i q.,. ith spced contr0i o i l6l primary current injection set 220i. i0 l1z. i t!. olrtpirl current 20(r a (nriri) t ir[r iinr er | 62. stepper moror with digital controller ino. t6t. shaded poie motor fractional t ip.2,l0t/.50 llz ,o. d.shonfloorfurnitureandmaterials for2(l+lliilit::trr,;dditrinli .tctns are required 164. working bench l,5.rx 1.21) * x11.75 :rl , :rs. t65. wiring board : n]etcr i :;,elcir^ith0.j llio. incter projectr,rii (,rr lh. top t 66. lnstn rctors table lo. 167. instnrctors chair .. ,)s. 168. metal rack l00cm x i 50crr x..l ictn 169. [ ockers with dralvers 2.5 nr r 1.20 rn r 0. 5 rn { lc dra,r,er*10 tirauer) i lil f.acir l iainee 170. almirah 2. i rn r 1.2[t m x 0.5 nr ] ,lr o. 171 black board/white board lrninirnurn 46 lect, , t fo. 112. fire extinguisher co2 ,./ k( i i n rs. t7 3. fire bucket slselof six) etc ...

Urban Improvement Trust - Rajasthan

32265199 various civil works and maintenance works in sub division i of division ii b ( arc ) civil worksclearing and grubbing road land including uprooting rank vegetation, grass, brush, shrubs, saplings and trees of girth upto 300mm, removal of stumps, disposal of unserviceable material and stacking of serviceable material upto 1000m from road boundary. (morth specification : clause 201).by manual means : in area of light jungle 2 clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared. 3 silt clearance of drains, channels and canals with lift 1.5 mtr. and lead up to 50 mtr. 4 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils 5 add extra over item no. 1.8 and 1.9 (sechedule item no 1) for every additional lift of 1.5 m or part thereof : 6 above 1.50 to 3.00m 7 m 35,60mm thick to be used in light traffic (light traffic is defined as a daily traffic up to 150 commercial vehicles exceeding 30 kn laden weight, or an wquivalent up to 0.5 million standerd axles (msa) for a design life of 20 years (a standerd axle is defind as a single axle load of 81.6 kn ) like pedestrain plazes, shopping complexes ramps, car parks, office drveways , housing colonies , office complexes , rural roads with low volume traffic ,fram houses, beach sites, tourist resorts, local authority footwys ,residential roads, etc. 8 category bdenated only two side like i,z,t shape etc. as per irc sp 63:2004 9 random rubble dry stone kharanja under floor. 10 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 11 m10 grade nominal mix, 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 12 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix 13 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix 14 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix 15 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 16 anti termite treatment of floor using imidacloprid 30.5% ec non repellent, odorless, low dose, environimentally safe terniticide with rapid action non corrosive stain free manufactured by bayer or equivalent company by drilling 12mm diameter holes 300mm apart injecting the emulsion as specified by the manufacturer and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area dpe 12mm dia termitube system with required number of junction boxes are to be installed. the termitube will run all along the perimeter wall both inside and outside. in the middle area the termitube to be installed at an interval of 1.00 mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. after successful testing of termitube, pesticide emulsion of imidacloprid 30.5% ec mixed with water in the ration of 1:474 will be pumped by a motorized spray pump from the junction box in specified manner. the plinth area of the area treated will be measured for payment. 17 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for : 18 columns, pillars, posts and struts etc. 19 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in: 20 cement mortar 1:6 ( 1 cement : 6 sand). 21 cement mortar 1:4 ( 1 cement : 4 sand). 22 cement mortar 1:3 ( 1 cement : 3 sand). 23 random rubble stone masonry with hard stone in superstructure aboveplinth level and upto three levelabove 30cm. thick walls in : 24 cement mortar 1:3 ( 1 cement : 3 sand). 25 cement mortar 1:4 ( 1 cement : 4 sand). 26 cement mortar 1:6 ( 1 cement : 6 sand). 27 pointingonstonemasonryincementsandmortar 1:3 (1 cement : 3 sand) : 28 flush / ruled/ struck or weathered pointing. 29 providing and laying damp proof course with cement concrete grade m 150 (1 : 2 : 4) mortar prepared with 1% solution of water proof compound complete and not applying 2 coats of hot bitumen complete as per specifications. 75mm thick 30 50mm thick 31 75 mm thick 32 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for : 33 suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 34 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. 35 thermo mechanically treated bars (conforming of relevent is code) 36 flyash flyash brick work with flyash flyash bricks of class designation 75 in superstructure above plinth level upto floor three level in all shapes and sizes in : 37 cement mortar 1 : 4 (1 cement : 4 coarse sand) 38 cement mortar 1 : 6 (1 cement : 6 coarse sand) 39 half flyash brick masonry in foundation & plinth using flyash bricks of designation 75 40 cement mortar 1 : 4 (1 cement : 4 coarse sand) 41 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 42 12mm thick. 43 20mm thick. 44 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3 fine sand) 45 making grooves as per design in plaster 10mm to 20mm wide. 46 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 47 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : 48 two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. 49 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. 50 new work 51 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 52 painting with synthetic enamel paint of approved brand and manufacture togive an even shade : 53 two or more coats on new work 54 150cm high fencing with angle iron 50x50x6mm. placed at every 3mtr. apart 30cm. in ground embedded in cement concrete 1:3:6 (30x30x45cm) corner and every tenth post to be strutted with 50x50x6mm. angle iron provided with 6 horizontal lines and two diagonals of black barbed wire between two posts fitted and fixed with g.i. staples including earth work in excavation etc. complete. 55 grading roof for water proofing treatment withwater proffing compound 56 cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 57 providing and fixing pressed steel door frames confirming to is 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike plate and shock absorbers as specified and applyinga coat of approved steel primer after pre treatment of the surface including filling with cc 1:2:4(m15 grade) complete as directed by engineer in charge : 58 profile b 59 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure a: 30 mm thick . 60 decorative teak veneer both side 61 providing and fixingaluminum workfor doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285,fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required pvc/neoprene felt etc. aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing /paneling , c.p. brass/ stainless steel screws al. tower bolt & al. handle & al. aldrop etc.,all complete as per architectural drawings and thedirections of engineer in – charge .(glazing and paneling to be paid for separately). : for fixed portion 62 polyester powder coating aluminum( minimum thickness of powder coating 50 micron) 63 providing and fixing of plastic shutter infill made from extruded multi chamber hollow p.v.c. section having cross section of 200 x 20 x 1 mm and shutter frame made from extrude p.v.c. section in the configuration of double walled c section having an overall cross section of 40 x 37 mm and door fittings such as hinges, aldrop, handles, stopper, locking bolt will be provided. 64 providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (is 1038 1983) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required :partly fixed and partly openable [ fixed area not to exceed 33%] 65 for shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). 66 polyester powder coating aluminum( minimum thickness of powder coating 50 micron) 67 providing and fixing superior quality like hardvyn or equivalent hydraulic door closure. 68 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 300mm x 450mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 69 providing and fixing 1st quality mat finished ceremic tile size 300x300mm confirmingto is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). 70 providing and fixing 15 to 20 mm thick granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12 mm (av.) thick base of cement mortar 1 : 3 (1 cement : 3 coarse sand) jointing with white cement mortar 1 : 2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of : 71 good quality south black above 3601 cm2 slabs 72 extra for providing edge moulding to 15 18mm thick marble/ granite stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. 73 granite work (full edge moulding ) 74 p & f 1st quality heavy duty vitrified glazed mat tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to is 15622 of approved make in all colour and shade, laid with 20 mm thick cm 1: 4 including grounting the joints with white cement and matching pigment etc complete. 75 size600 mm x 1200mm 76 providing & fixingbrown kota/ mandana / dholpur/ slate stone incladding / flooring structuralbase with white cement & tinex chemical& ss clamp and fasteners (of approved brand) laid and jointed with white cement slurry mixed with pigment to match the shade of the slab as per drawing attachedcomplete in all respect as per direction of engineer in charge & architect with all lead & lift. the stone measurement will be done of outer most dimension. thickness of stone 25 30mm. 77 polished blue kota stone flooring skirting, laid over 20 mm thick base of c.m. 1 : 4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete :for area of each slab from 901 to 2000 sq.cm : 78 25 mm thick slab. 79 s/f of fire bricks on edg flooring with fire bricks suitable for 1300 degree centigrade safe working temperature as per is :8 specification laid on & filling of joint by fire resistant mortar/adhesive of required thickness as per directed on a bed of 20 mm thick 1:2 cement mortar of bricks 9 x 4.5x 3 (rate approved year 2008) 80 providing and fixing of glass moisac tiles ( bisseze marke ) size 20 x 20 x 4 mm applied with aaproved adhesive as per specification and direction of engineer in charge 81 providing and fixing staincase railing 90 cm high from nosing of made offollowing specifications. 82 50 mm outer dia (2 mm thick) s.s. pipe hand rail. 83 40 mm outer dia (2 mm thick) s.s. pipe baluster @ 1.00 mtr. 84 4 nos. 20 mm fs. s pipe intermediate runners parallel to hand. 85 s.s. shoe 1.60 mm thick 75 mm outer dia. at each baluster 86 baluster to be welded with s.s. plate 50 mm dia (3 mm thick) anchored in c.c. block with suitable dash fastners 87 50 mm dia & 2 mm thick s.s. pipe for start and end vertical ornamental posts to be provided as per direction of engineer in charge 88 the stainless steel work shall be brushed steel finish with all joints/welds properly grinded to final finish. the stainless steel shall be 304 grade and shall confirm to relevant i.s. 89 providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide.extra if square,rectangular hollow tubularsections are used or grill made by flats only 90 decorative plaster work with spectrum textured coating as per approved colour and shade complete as per manufactures specifications. 91 grit textured @ 2.5 to 3.0 mm thick. 92 ornamental cement plaster in cement sand mortar1 : 4 making kangooras etc. as per jaipurpractice. 93 supplying and fixing machine cutdressed 75 mm pinksand stone (bansi paharpur) dasa/ coping wth ornamental shape having moulding and pan shape engraving as per required pattern with engraving depth of 5 mm (average) in single piece of length 90 cm to be laid on cement mortar 1:4 (12 to 20mm thick) including pointing with admixture of pigment matching with the stone shade. 94 providing corrugated g.s. sheet roofing including vertical / curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces)excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required. 95 0.63 mm thick with zinc coating not less than 275 gm/m2 96 supply & spreading ofgood earth at site complete including loading unloading & transportation etc. 97 supply of dry manure including loading unloading,transportation & stacking at site. 98 farm yard manure(organic) 99 spreading of manure and good earth in required thickness (cost of manure and good earth to be paid separately). 100 laying of lawns including ploughing levelling breaking of clods manuring & removal of stones etc.(cost of manure or extra good earth to be paid seperately) maintenance of lawns for 30 daysor more till the grass forms a thick lawns free from weeds & fit fo 101 in rows 7.5 cms. apart in either direction 102 construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting by vibratory roller 8 10 tonne to meet requirement of table 300 2 including cost of compensation for earth taken from private land with lead upto 1 km as per morth specification : clause no. 305. 103 rough chisel dressed stone flooring over 20 mm (av.) thick base in cm 1 : 6 including pointing with cement mortar 1 : 2 (1 cement : 2 stone dust) with and admixture of pigment to match the shade of stone with joint thickness upto 15 mm : 35 mm thick red sand stone. 104 p & f european type white glazed vitreous china 1st quality double syphonic w.c (is :2556 mark) with p or s trap including cutting and making good the wall and floor 105 p & f indian type white glazed vitreous china 1st quality w.c. orissa pan (is :2556 mark) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor: 106 size 580x440mm. 107 p & f low level flushing cistern of 10 ltr. capacity (is : 2556 mark) o9f approved make with colplete fitting ,c.i. brackets duly painted , brass ball cock with ball, (is :1703 mark)complete including cutting and making good the wall. 108 wvc with c.p. brass bend. 109 p & f wvc wash basin (1st quality, i.s. : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p. pillar cock (is : 8934 mark) &32 mm c.p. brass waste coupling of approved make, 25 mm g.i. waste pipe complete including cutting & making good the wall.: 110 size 550 mm x 400 mm dia for counter top 111 1.0 mm thick salem stainless steel aisi 304 & is 13983 1994kitchen sink of approved make (nirali, neel – kanth, jaina, faber castell )with large waste coupling. 112 (24 x 18 x 8) (20x16x8) 113 p & f inlet connection (angle valves) superior quality, of approved make, for wash basin, gyser etc. 114 c.p. inlet connection 15mm.brass (is : 8931 marked) with 37 cm long pipe and nut. 115 p & f pvc storage tank isi marked (is : 12701) indicating thebis license no),of approved make with cover, 25mm dia 1m long g.i. over flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 116 1000 litres capacity. 117 providing and fixingsuperior quality (jaguar contiental ) cp brassfittings complete as per direction of ei 118 bib cock with long thread 15 mm nominal size 119 brass / gunmetalhalf turnwt. 1 kg.ofapprovedquality / make,25mmnominalbore. 120 p & f full way valve (is:778 mark) or wheel valve of approved make 121 gun metal 32mm nominal bore. 122 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. (concealed work including cutting chases and making good the walls etc.,) 123 20mm nominal outer dia pipes 124 32mm nominal outer dia pipes 125 p&f rigid pvc pipe (is:4985 mark) class ii/ (4 kg. /cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 126 110 mm dia 127 160 mm dia 128 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant: 129 coupler (socket) 130 110mm dia 131 160 mm dia 132 plain tee 133 110mm dia 134 160mm dia 135 door tee 136 110mm dia 137 bend 45 138 110mm dia 139 vent cowel 140 110mm dia 141 door bend (left & right) 142 110mm dia 143 pipe clip 144 110mm dia 145 plain floor trap 146 110mm dia 147 p trap 148 110mm dia 149 socket plug 150 110mm dia 151 door cap 152 110mm dia 153 construction of chamber in all type of soil with 300 mm thick masonry in cm 1:6 m 10 cm thick c.c. 1:5:10 in foundation, 20mm thick insider plaster in cm 1:6, finished with floating neat cement, 50mm thick m 15 grade c.c. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. 154 do size 450 x 450mm depth upto0.5 m cement cover with frame 155 wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) ofapproved make in surface / recessed isi marked medium duty pvc conduit & its accessories, round tiles,hot dipped galvanized modular box with earth terminal, 6 a modular switch,modular plate with grid plate,screws,making connections, testing etc. as required. 156 short point (up to 3 mtr.) 157 medium point (up to 6 mtr.) 158 long point(up to 10 mtr..) 159 wiring of twin control light point with 1.5 sq.mm fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade and 1.5 sq.mm.fr pvc insulated unsheathed flexiable copper earth conductor 1.1 kv grade(is: 694) of approved make in surface/ recessd isi marked medium duty pvc conduit & its accessories, round tiles, 18 swg m.s. box with earthing terminal, 6 amp two way switch, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. 160 medium point (up to 6 mtr) 161 wiring of 3 pin 6 amp light plug point with 1.5 sq.mm fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade and 1.5 sq.mm.fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade(is: 694) of approved make in surface/ recessd isi marked medium duty pvc conduit & its accessories, round tiles, 18 swg m.s. box with earthing terminal, 6 amp switch & 6 amp socket, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. 162 on board 163 medium point (up to 6 mtr) 164 long point (up to 10 mtr) 165 s&f following sizes (dia.) of isi marked medium duty pvc conduit along with accessories in surface / recessed using saddles, clamps, fastener as required includingcutting the wall, covering conduit and making good the same as required. 166 25 mm 167 32 mm 168 50 mm 169 supplying and fixing of power plug point modular accessories on hot dipped galvanized modular on surface or in recessed with suitable size of grid plate with cover plate including cost ofmodular 16 amp. switch and socket outlet, making connection , testing , etc. as required. 170 p&f metal clad industrial plug top & socket unit with pin and sleeve type contact on porcelain/ bakelite base in sheet steel enclosure (without mcb) including making connections, testing etc.as required 171 single / double pole(three pin) 172 32 a 173 providing & fixing isi marked 6 amp bakelite batten/angle holder including making connection testing etc. as required. 174 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor isi marked (is:694) of 1.1 kv grade and approved make in existingsurface or recessed conduit/casing capping including making connections etc. as required. 175 2 x 2.5 sq. mm. + 1x1.5sqmm 176 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 177 p&f 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c/ d tripping characteristic) isi marked is 8828(1996)]/ conforming to iec 60898 in existing board/sheets including making connections, testing etc. as required. 178 single pole mcb 179 6 a to 32 a rating 180 four pole mcb 181 40 a 63 a rating 182 four pole mcb 183 6 a to 32 a rating 184 p&f recessed/ surface mounting heavy duty horizontal type sheet steel distribution board phophatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar,masking sheet, conforming to is13032 & is8623 including making internal dbterminations with copper lugs , testing etc. as required. 185 double door (single phase) 186 12 way 187 double door (three phase) 188 8 way 189 p/laying p.v.c./ xlpe insulated & p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor of is:1554 p i / is :7098 p i of group 1 of approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand,iind class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. 190 25.0 sq.mm 191 4 core 192 50.0 sq.mm 193 120.0 sq,mm 194 3.5 core 195 150.0 sq,mm 196 supplying and making one end termination with heavy duty single compression brass gland sibg type, heavy duty aluminium lugs duly crimped with crimping tool, pvc tape etc for following size of armoured pvc insulated & pvc sheathed/ xlpe aluminium conductor cable of 1100 volt grade as required of size. 197 3.5 x 120.0 sq.mm 198 4 x 25.0 sq.mm 199 p/laying p.v.c./ xlpe insulated & p.v.c. sheathed cable of 1.1 kv grade with copper conductor of is:1554 p i / is :7098 p i of group 1 of approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand,iind class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. 200 10.0 sq.mm 201 4 core 202 supplying and making one end termination with heavy duty single compression brass gland sibg type, heavy duty copper lugs duly crimped with crimping tool, pvc tape etc for following size of armoured pvc insulated & pvc sheathed/ xlpe aluminium conductor cable of 1100 volt grade as required of size. 203 4 x 10.0 sq.mm 204 sitc of wall/ free standing floor mounted dust and vermin proof compartmentalisedcubical panel made out of crca sheet , required hardware,duly treated for derusting in 7 tank process with dephosphating and with powder coating on both side of panel in desired shadethe panel having pu/ neoprene rubber gasket of not less than 3mm thickness , separate detachable gland plate m.s. base channel ,hinged door with locking arrangement for equipment/switchgear. thickness of sheet shallnot be less than 1.6 mm up to 600 mm length / widthof any compartment and be of 2.0 mm above 600 mm. load bearing structure shall beof 2.0 mmthick sheet supported by base m.s. channel if required . side walls and cable alley compartments having bolted type doors with / withoutdetachable extension type structure. (only outer area on all sides shall be measured & panel to be fabricated from cpri approved fabricator) 205 supplying and fixing of aluminium / copper bus barby means of smc / dmc type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. 206 electrolytic grade aluminium bus bar 207 sf of (0 500) v range volt meter on existing panel , making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required. 208 analog type ( 96mm x 96mm ) 209 sf of ct operated direct reading typeampere meter on existing panel , making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required. 210 analog type ( 96mm x 96mm ) 211 below 500 a 212 sf ofcurrent transformer, with all necessary support in existing panel including connection etc. as required . 213 up to 150/5 ratio, 10 va, class 1 accuracy 214 sf of selector switch of 10 a for voltmeter (4 position ) including making connection etc.as required . 215 sf of ct linked selector switch of 10 aforampere meter (4 position ) including making connection etc.as required . 216 sf of110/220 v, led (22.5 mm dia ) indicatinglamp with integral circuit, terminal block, including connection etc. as required. 217 red/yellow/green colour 218 supplying and drawing fr pvc insulated & unsheathed flexiable copper conductor isi marked (is:694) of 1.1 kv grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. 219 1 x 1.5 sq.mm 220 1 x 2.5 sq.mm 221 1 x 4.0 sq.mm 222 1 x 6.0 sq.mm 223 sitc of self healing mpp/mp type shunt capacitor (banks) conforming to is:13340 41 / iec :831 1&2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( psd ) and shall have dissipation factor less than 0.0025 at 50 hz and total wattage loss less than 0.5 watt per kvar . including making connections with suitable capacity conductors/cables testing etc. as required. 224 heavy duty three phase 440 v , 50 hz capacitor (bank) 225 sitc of microprocessor based three phase sensingpower factor correction relay having following sensing capacitysecondary current , self analysing auto c/k setting according to targeted power factor setting, the relay shall havedigit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, indication of switching on units, auto/manual status, and shall have over load protection, no volt release , having multi parameter like kw, kva, kvar,metering facility as required. 226 6 to 8 stage 227 sensitivity upto 50 milli amp 228 p & f ofcam operated rotary switchs on existing panel with 2 way and off postion 229 one pole 230 16 amp 231 p & f of440 volt 3 pole capacitor(ac 6 b ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors/ reactors to limit the inrush current, conforming to is:13947 4 1/iec:947 4 1, din rail mounting type including making connections, testing etc. as required. suitable for following capacity capacitor bank. 232 up to 6 kvar 233 7 to 10 kvar 234 p&f 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c/ d tripping characteristic) isi marked is 8828(1996)]/ conforming to iec 60898 in existing board/sheets including making connections, testing etc. as required. 235 triple pole mcb 236 6 a to 32 a rating 237 p&f on load change over switch, front handle operated, four pole 415 v conforming to is:13947 p iii including connections , testing etc. as required in the following rating: 238 open execution type 239 200 amp 240 sitc of quick make and quick break4 polecurrent limiting mccb having following current rating, short circuitbreaking capacityat 440/415 v, 50 hz; o/l & s/c settings and conforming to is 60947 2 / iec 60947 2 with front face and centralised adjustable, line load interchangeability, having positive isolation capability, provision for uvr , shunt trip ,earth fault trip, push( test) to trip , including making connections with lugs & spreaders,etc. as required. 241 with thermal magnetic release 242 up to 160 amp , 25 ka, adjustable o/l & fixed s/c setting, ics = 100 % icu 243 plate earthing as per is:3043 withcopper earth plate of size 600mm x 600mm x 3.0mm by embodying3 to 4 mtr. below the ground level with 25mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer, nipple ,wire meshed funnel, and c.c.finished chamber covered with hinged type with locking arrangement c.i. cover,c.i. frame of size300mm x 300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required. 244 s & laying following size earth wire/stripin horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required. 245 8 swg copper wire 246 providing & fixing of heavy duty capacitor start 900/1400 rpm single phase isi marked exhaust fan is:2312 marked in existing opening making connections, testing etc. as required 247 300 mm sweep (900/1400 rpm) 248 p & f double ball bearing capacitor start, aluminium body & blade ceilingfanwith down rod up to 30 cm with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. 249 1400 mm sweep 250 p & f of ip 20 led tube light 20 watt with external batten made from crca sheet steel suitable to replace t 8/t 12 tube light, integral driver, 2000 luman + 5% tolerarrce system luman efficiacy of 100 lm/ watt minimum expected life time of 25000 burning hours, cct 5700 k ansi, cri 80, driver efficiency >85%, life expectancy of driver rnin 30000 hrs. pf 0,95 at full load/ 230 volt ac. 251 p & laying xlpe insulated is:7098/ii/85 of group1 and approved make h.t.cable for working voltage 11 k.v.earthed direct in ground including excavation of 30cmx100cm size trench, 25cmlayer of river sand, iind class bricks covering, refilling earth, compaction of earth, making necessary connection testing etc.as required of size. 252 3 core 185.0 sq.mm ...

Military Engineer Services - Rajasthan

31963069 repair / maintenance of dg set and other connected items , repair / maint ofexternal electric works, steet lightsand lt ug cables at west camp, south camp and dbs& motigarh, pugal , rd 498 ascon nodes andrepair / maint of summer appliances , deep freezer, water cooler & acat age mffr under ge ( n ) bikaner taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified.note : work will be carried out upto 4th storey of bldgs also as per pirection of engr in charge including necessary formwok and scaffolding required as per site conditions & no extra payment shall be made on this account. 2 rendering 15 mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:4 , rendering is to be finished even and fair without using extra cement ( up to 4th storey with necessary scaffolding ) complete all as specified and as directed by engineer in charge. 3 m&l rendering cement plaster, 15 mm thick on fair faces of brick / concrete surfacesof wall in cement mortar 1:6 finished even and smooth w / o using extra cement complete all as specified. 4 rendering 10 mm thick on fair faces of brick or concrete surfaceceilings, in cement mortar 1:3 , rendering is to be finished even and smooth without using extra cementcomplete all as specified and as directed by engineer in charge. 5 preparation of new plastered or unplastered surfaces of ceilings to achieve smooth and even surface and applying three coats of white washingcomplete all as specified and as directed by engineer in charge. 6 preparation of new plastered or unplastered surfaces of walls to achieve smooth and even surface and applying three coats of white washingcomplete all as specified and as directed by engineer in charge. 7 material ad labour for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over two coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified. 8 preparationof newplastered / concrete surfaces of walls to achieve smooth and even surfaceandapplying two coats of cement based paint over and includingone coat of primer ( up to 4th storey with necessary / scaffolding ) complete all asspecified andasdirected by engr in charge. 9 supply and fixing in repair brass face for cp / brass bib tap, angle / stop cock, pillar cock, wall mixer, whb mixer, etcfor 15 mm bore pipecomplete all as specified and as directed by engineer in charge. 10 supply and fixing in repair, pvc knob or flushing handle for flushing cistern of capacity 10.0 litres , complete all as specified and as directed by engineer in charge. ( sample as approved & kept in ges sample room ) 11 supply and fixing in repair, pvc float valve suitable for flushing cistern of capacity 10.0 litrescomplete all as specified and as directed by engineer in charge. ( sample as approved & kept in ges sample room ) . 12 supply and fixing in repair, pvc syphonic kit for flushing cistern of capacity 10.0 litres, complete all as specified and as directed by engineer in charge. ( sample as approved & kept in ges sample room ) 13 supply and fixing in repair, pvc bend suitable for flushing cistern of capacity 10.0 litres, complete all as specified and as directed by engineer in charge. ( sample as approved & kept in ges sample room ) . 14 supply and fixing in repair, pvc syphon washer suitable for flushing cistern of capacity 10.0 litrescomplete all as specified and as directed by engineer in charge. ( sample as approved & kept in ges sample room ) 15 repairs to steel window, ventilators of any size to make it functional ( including slot pin, hinge, hook and eye of standard quality where required ) , resecuring of windows wire gauge and railings / grills by using welding equipments, complete all as directed. 16 repair / easing ofwooden door any type, glazed or panelled, by trimming the side of door shutter where rubbing with chowkhat, unscrew the hinges screws and lift the door and fix with screws, tightening of wire mesh etc all as per engr in charge. 17 material and labour for ( a ) repairing aluminium shutters ( door / window ) including refixing, tighteningand making good with usingrubber / beads and others small fixtures / fittings if required and making serviceable all as specified and directed by engr in charge. 18 ( b ) aluminium door locks ( sample approved by engr in charge ) 19 taking down shutters of any description n.exc 1.00 sqmeach and removing from the site all as specified & directed. 20 taking down shutters of any description exc 1.00 sqm and n.exc. 2.00 sqm each and removing from the site all as specified & directed. 21 taking down chowkats or frames with shutter ( without taking off shutter from the frame ) n.exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from siteall as specified. 22 taking down chowkats or frames with shutter ( without taking off shutter from the frame ) exc 1.5 sqm&n.exc 4 sqm each including cutting holes for taking out hold fast or dismantling brick workand removing from site all as specified. 23 s&f pressed steel framesof size 125mm x 60mm made outof size 1.25mm thick ms sheet for doorssingle rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast, tie bar including necessary fixinglugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type b 1 including pcc 1:3:6 as in back fill to chowkats all as specified. 24 s&f pressed steel framesof size 105mm x 60mm made outof size 1.25mm thick ms sheet for doorsdouble rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast, tie bar including necessary fixinglugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type b 1 including pcc 1:3:6 as in back fill to chowkats all as specified. 25 supply and fixing factory made, plain framed, panelled shutter ( two panel ) 35mm thick, 2nd class hardwood with lock rail and panel of 9 mm b.w.p commercial ply. the size of rail and stiles as per as per is:1003 ( part i ) , kiln seasoned and chemically pressure treated complete all as directed by engr in charge. 26 supply and fixing 35mm thick2nd class hard wood glazed, gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitredand rebatedsash bars, stiles and rails as specified in ssr part i sec 8 clause 8.24 ( a ) complete all as specified 27 s&f flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified.note : sampel approved by engr in charge or ge. 28 s&f solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all asspecified and as directed by engr in charge. 29 s&f factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, suppplyingand fixing in the frame at site as per specification & drawing complete all asspecified and as directed by engr in charge. 30 s&f factory made solid pvc moulded door shutter 28 to 30 mm thick ( stiles ) with particle board core with 2, 4 , or 6 raised panel design with 2 mm thick mouldedprelam pvc sheet on the front face & 2 mmprelam pvc sheet on back face, to be fitted in the mild steel frame welded / sealed to the stiles and rails with suitable pvc sheet beading, and joined together with solvent cement, supplying and fixing in the framme at site as per specification and drawing, complete all asspecified and as directed by engr in charge. 31 taking down of old / unserviceable kitchen cabinet / cupboard including all fixture and fitting, complete all as specified and directed.note: for measurement superficial area in elevation shall be measured. 32 s&f factory made 18mm ( +0.7mm ) thick celuka pvc ply of density 600kg / cbm manufacured by an iso 900 2008 certified company. one side prelam and other side plain18mm thick celuka pvc ply for kitchen cabinet shutter and also manufactuers test report and test certificate is mandatory with each and every supply of the material complete as per manufacturers specifications and drawing and as directed. 33 s&f factory made 18mm ( +0.7mm ) thick celuka pvc ply of density 600kg / cbm manufacured by an iso 900 2008 certified company. plain 18mm thick celuka pvc ply for shelf / partitions / drawer and also manufacturers test report and test certificate is mandatory with each and every supply of the material complete as permanufacturers specifications and drawing and as directed. 34 s&f factory made 5mm thick pvc of density 600kg / cbm manufacured by an iso 900 2008 certified company. plain 5mm thick pvc sheet paneling for back side ( wall side ) and also manufacurers test report and test certificate is mandotary with each and every supply of the material complete as per manufacturers specifications and drawing and as directed. 35 s&f 100mm size stainless steel handle complete all as specified and as directed. 36 s&f ball rolling sliding channels of size 450mm length fixed in cupboards with screws as in drawers 37 s&fauto hingesof size 150mm length fixed in cupboards with screws for holding stainless steel baskets as in drawers 38 s&f self adhesive tape of 18 / 19mm width , hot pressed & pasted on sides & bottom of edges of cupboards shutters 39 s&f steel fasteners of size 75mm long drilled and fixed to walls 40 s&f 50mm dia and 75mm long steel supports fixed with bolt at bottom of cupboards box all as specified 41 pressed steel cup board frameof ms sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including pcc 1:2:4 as in filling to back of chowkats includingbutt hinges 100 mm long. piano hinges measured separately. 42 prelaminated mdf board 19 mm thick as in shutters / shelves ( exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame worknincluding lipping ( 15 mm thick three sides and 20 mm thick lipping hinge side ) around the shutter complete all asspecified and as directed by engr in charge. 43 s&f in repair continuous ( piano ) hinges, width of flaps ( when open ) 30 mmheavy duty mild steel, bright finish or electrogalvanised sutable for 19mm thick shutter and fixed, complete all as specified. ( isi marked ) 44 s&f butt hinges of mild steel cold rolled medium weight of size 100mm as specified. 45 supply and fixingfor stainless steel medium weight butt hinges, 100mm , complete all as specified and as directed 46 s&f aluminium anodised, barrel tower boltssize 150 mm of extruded section and fixed complete all as specified. ( isi marked ) 47 s&f aluminium handles, fabricated type, anodised size 100mm, anodised section and fixed complete all as specified. ( isi marked ) 48 s&f aluminium alloy, anodised, sliding door bolt size 250 mmwith hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified. 49 s & f hasp & staple safety type aluminium anodised with mild steel hinges spin including bolt to hinges plate fixed with screws of 75 mm in length. 50 s&f aluminium hanging floor door stopper, twin rubber stopper, size 100mm , anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. 51 m&l for 50 mm magnetic catches with brass body and striking plate including letting in as fixed complete all as specified and directed. 52 s&f 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified. ( isi marked ) 53 s&f in repair aluminium bottom door seal with brushes, length 1.2 mtr, fix with screw, suitable for wooden door complete all as specified. 54 supply and fixing in repair mild steelhelical ordinaryrat tail rod patternsprings300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed. 55 s&f in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 rm length, with stainless steel brackets near to ends with stainless steel finialsfor 25mm dia drapery rod at both ends. the drapery rod shall be projecting 150 mm outer side from the clear opening of doors / windows. ( including necessary fittings ) 56 s&f powder coated aluminium door shutter including frame of hollow section 101mm x 44.00mm xthickness not less than 1.53 mm including aluminium anodized powder coated of hollow section glazed shutter of stiles size 85mm x 44.45mm xthickness not less than 1.56mm having grooves for aluminium beading and top rail of hollow section 83.5mm x 44.45mmxthickness not less than 1.50mm, lock rail of hollow section 83.5mm x 44.45mm xthickness not less than 1.50mm and bottom rail of hollow section 114.3mm x 44.45mmx thickness not less than 1.50mm , one derived handle 300mm long, 100mm long butt hinges or aluminium floor type hydraullic door closer, aluminium mortice lock 65mm 4 levers of godrej make and glazing with select quality tinted glass 5mm thick or panelling with acp sheet and cleat rubber packing aluminium beading including aluminium hardware fitting complete all as specified and as directed by engr in charge and approved by ge. 57 m&l aluminum power coated, sliding windows three track with mosquito proofing with style 44.4x44.5x2mm thick including 4 mm thick coloured / tinted / frosted glass panes including all necessary fittings and fixturescomplete. 58 m&l for anodised aluminium grills, 6mm dia size 100x100mmfixed to aluminium windowsand thickness of powder coating not less than 50 micron, complete all as specified. 59 taking down wall panelling including any type of aluminium door, windows and partition in any position complete all as specified and as directed by engr in charge. 60 s&f in repair aluminium extruded section body, door closer hydraulically regulated, designation no. 1, universal type, suitable for door shutters of 700mm in width and of weightnot more than 35kg and fixed. 61 supply and fixing in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty. 62 s&f in repair brass mortice lock with brass handles and fittings , 4 leververtical type, size 100 mm including complete accessories complete all as specified. make: links locks / godrej / harrison 63 supply and fixing5 mm thicksheet glass ordinary quality coloured / tintedand glazed in squares, n.exceeding 0.5 sqm in each pane. 64 supply and fixing5mm thick ( minimum ) glass sheet selected quality coloured / tinted / frosted and glazed in squares, n.exceeding 0.5 sqm in each pane. 65 supply and fixing 4mm thick aluminium composite panel ( coloured sheet ) and in additional other accessories for fitting complete all as specified by engr in charge. 66 material & labourfactory made steel windows double shutter box type, outer frame made out of erw tube p section ( 60x45x25mm ) and shutters of erw tube p section ( 50x35x20mm ) operable shutters side hung includding pistol hinges with two nos of ms tower bolts 150mm size on each shutter steel handle and stopper of z section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitabel fittings / openning for cooler / ac where required .steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per drg no cepz / td 324 / 07 1 / 3 to 3 / 3 all as specified and directed by engr in charge.note: the quoted rate against the above item shall also include ( i ) 04 nos ms steel lugs of 20x5mm ms flat 20cm long over all welded to frames ( ii ) pcc block for embedding lugs. 67 ditto all as per item no 66 but in ventilators any size. 68 s&f framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framedbalusters; walk ways; railings; framework of water tanksand similar work conforming to fe.290.gde e 165 69 hacking out old broken glass ( any thickness, size quality or description ) from any types of wooden / steel / alum ( up to 4th storey ) frames or stone concrete or brick surrounds glazed with putty or fixed with beads. 70 s&f4 mm thick sheet glass ordinary quality glazing with oil putty or any type of beads in square n.exc. 0.5 sq each pane in any type of frame of iron / steel / wood / aluminium as required at site complete all as specified ( uptofourth storey with necessary scaffolding ) , all as specified. 71 s&f 4 mm thick figured glass, pin head type and glazing with oil putty or any type of beads in square n.exc. 0.5 sq each pane in any type of frame of iron / steel / wood / aluminium as required at site complete all as specified ( uptofourth storey with necessary scaffolding ) , all as specified. 72 securing glass of any description in existing wooden and iron frames glazed with putty / beads including removing loose or decayed putty / beads, painting / oiling one coat on rebates, grooves, reputtying and painting / oiling puttied surface to match existing work ( new length of frame reputtied shall be measured. 73 supply and fixing stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple 74 supply and fixing galvanised mildsteelwire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specifiedfixed with stainless steel wire staples. 75 supply and fixingin repair galvanised mildsteelwire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specifiedfixed with stainless steel wire staples. 76 s&f in repair central hole basin mixer without popup waste system with 450mm long braided hoses also available all as per directed and specified.make : jaquar, cat no cqt 23167b or equivalent in cera / hindware 77 supply and fixing in repairwall mixer non telephonic shower arrangement with connecting legs and wall flanges, cast copper alloy, chromium plated, complete all as specified make :jaquar, cat no cqt 23219or equivalent in cera / hindware. 78 s&f in repairwall mixer 3 in 1 system with provision for both hand shower & overhead shower complete with 115mm long bend pipe on upper side, connecting legs & flanges ( without hand & overhead shower ) complete all as specified. make: jaquar, cat no: cqt 23281upr or equivalent in cera / hindware. 79 s&f in repair hand shower 120mmdia round shape multi flow with cascade effect ( abs body chrome plated with gray face plate ) with rubit cleaning systemcomplete all as specified. make : jaquar, cat no hsh1731 or equivalent in cera / hindware. 80 s&f in repairsink mixer with swinging spout ( wall mounted model ) with connecting legs & wall flanges complete all as specified. make: jaquar, cat no cqt 23309 or equivalent in cera / hindware. 81 s&f in repair sink cock with swinging casted spout ( wall mounted model ) with wall flange complete all as specified make: jaquar, cat no cqt 23347 or equivalent in cera / hindware 82 s&f in repair bib cock with wall flange cast copper alloy, chromium plated fancy type , complete all as specified. make : jaquar, cat no: sqt 23047 or equivalent in cera / hindware. 83 s&f in repair 2 way cp bib cock with wall flange, cast copper alloy, chromium plated fancy type, sutable for 15 mm gi pipe, complete all as specified. make : jaquar, catno: cqt 23041 or equivalent in cera / hindware. 84 s&fin repair angle cock with wall flange , cast copper alloy, chromium plated fancy type screwedfor 15 mm iron pipe, complete all as specified. make: jaquar, cat no cqt 23059 or equivalent in cera / hindware 85 s&fin repairexposed part kit of concealed stop cock with fitting sleeve, operating lever & adjustable wall flange ( compatible with ald 069 ) complete all as specified. make: jaquar, cat no: cqt 23069k or equivalent in kohler / artize. 86 s&f in repair 15mm bore cp bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified complete all as specified. make: jainko, essco, parko, prayag 87 s&fin repair 15mm bore angle valve with wall flange , cast copper alloy, chromium plated fancy type screwedfor 15 mm iron pipe, complete all as specified. make: jainko, essco, parko, prayag 88 s&fin repair 15mm borestop valves, cast copper alloy, fancy type, chromium plated with long shankandcup ( concealed type ) screweddown, highpressure, withcrutch or butterfly handle, screwed both ends foriron pipe orfor unions and fixed, complete all as specified. make: jainko, essco, parko, prayag 89 s&f in repair 15mm bore cp pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified. make: jainko, essco, parko, prayag 90 supply and fixing in repair health faucet ( abs body ) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and abs wall hook including making connections and fixed in position complete in all respect as specified.make: jainko, essco, parko, prayag 91 s&f in repair tubular towel rail, 20mm dia, d type, 60cm long between flangescomplete all as specified. make: jainko, essco, parko, prayag 92 s&f in repair chromium plated, towel ring, complete all as specified. make: jainko, essco, parko, prayag 93 s&f in repair chromium plated towel rack 600mm long without lower hangers, stainless steel complete all as specified. make : jaquar cat no akp 35781pfs or equivalent in cera / hindware. 94 s&f in repairstainless steel shop dishholder complete all as specified. make: jainko, essco, parko, prayag 95 s&f in repair toilet paper holder with flat recessed type stainless steel complete all as specified and directed., complete all as specified. make : jainko, essco, parko, prayag 96 s&f in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long . complete all as specified. make : jainko, essco, parko, prayag 97 s&f in repair corner glass shelf ( with bracket ) as per directed by engr in charge. make: jainko, essco, parko, prayag 98 s&f in repair waste coupling of chromium plated brass32 mm dia with long screwed shank and fly nuts complete as suitable for wash hand basinall as specified . make : jainko, essco, parko, prayag 99 s&f in repair waste coupling of chromium plated brass40 mm dia with long screwed shank and fly nuts complete as suitable for wash hand basinall as specified . make : jainko, essco, parko, prayag. 100 s&f in repair pvc connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore.make : jainko, essco, parko, prayag 101 s&f in repair pvc connection 15 mm x 600 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore. make : jainko, essco, parko, prayag 102 s&f in repairbrasschromiumplatedshower rosewith or without swivel joints, 125mm size, including fixing to steel pipe or unionmake : jainko, essco, parko, prayag 103 s&f in repair single piece wc with uf soft close seat cover, hinges, fixing accessories set and accessories set, cistern fittings, size: 660 x 365 x 765mm, s trap 300mm complete all as specified. make : cera, cat no s1013105 or equivalent in hindware / jaquar. 104 s&f in repair under counter basin white colour with fixing accessories set, size: 560 x 470x190, oval shape, including cpwaste coupling and pvc waste pipe complete all as specified. make : cera, cat no s2030104 or equivalent in jaquar / hindware. 105 s&f in repairvitreous china, wash basin white, flat back , size 550mmx400 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass.complete all as specified and as directed by engineer in charge.. make : cera, cat no s2040119 or equivalent in jaquar / hindware. 106 s&f in repair full pedestal for whbcomplete all as specified. make : cera, cat no s2090113 or equivalent in jaquar / hindware. 107 s&f in repair pvc valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, pvc 32 mm l bend of capacity 10.0 litres and making good to dismantled / damaged floor / surfaces, fixing in repair, complete all as specified and as directed by engineer in charge. make: cera, cat no b1010109 ( congo ) or equivalent in jaquar / hindware. 108 supply and fixing in repairpvc seat cover for ewc pan ( white ) of standardd quality including hinges bolt etc all as directed by engr in carge.make: cera cat no b1510121 or equivalent in jaquar / hindware. 109 supply and fixing in repair vitreous china ware pedestal type water closet white, with p or s trap including self closing seat cover, closed pattern with flat bottom, complete all as directed. make: cera, cat part no s1053101 or equivalent in jaquar / hindware. 110 s&f in repair wc orissa pattern white with integral foot rest580x 440 mm including l bend, &pcc bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified. ( rate of including in taking out and removal of old wc seat unhygienic condition ) make: cera, cat part no s3010102 ( calina ) or equivalent in jaquar / hindware. 111 supply and fixingin repair pvc waste pipe 32mm bore of required length complete. make: prayag cat no 329 or equivalent in polytuf / jindal. 112 supply and fixing in repair pvc waste pipe 40mm bore of required lengthcomplete for sink / whb . make: prayag cat no 330or equivalent in polytuf / jindal. 113 dismantling water tanks and removing to store of water storage tanks ( cap. 500 ltr to 1000 ltr ) complete all as specified and directed by engineer in charge. 114 dismantling water tanks and removing to store of water storage tanks ( cap. 250 ltr to 500 ltr ) complete all as specified and directed by engineer in charge. 115 supply and fixingrotational moulded polyethylene water storage tanks of1000 litres capacity, ( cylindrical vertical with closed top ) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in ssr part i including ptmt ball valves high pressure with epoxy coated aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified. make : vectus, sintex, sheetal. 116 supply and fixingrotational moulded polyethylene water storage tanks of 500 litres capacity, ( cylindrical vertical with closed top ) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in ssr part i including ptmt ball valves high pressure with epoxy coated aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specifiedmake : vectus, sintex, sheetal. 117 disconnecting of water tank of 500 ltr capacity setting aside ( or lowering if required ) for repairs, cleaning etc. and hoisting if required reconnecting and re fixing in position. ( cleaning repairing, etc. measured separately ) . 118 cleaning and removing all scale and dirt etc, from exc 250 & n exc 500 litres capacitytanks in any position and from mouths of circulating pipes etc, and disinfection completely by making all the arrangements and writing date of cleaning on side of tanks also containing completion from user complete all as directed. 119 cleaning and removing all scale and dirt etc, from exc 500 & n exc 1000 litres capacitytanks in any position and from mouths of circulating pipes etc, and disinfection completely by making all the arrangements and writing date of cleaning on side of tanks also containing completion from user complete all as directed. 120 supply and fixing in repair gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 25 mm bore pipe, including making connections complete all as specified and fixed. 121 supply and fixing in repair gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and fixed. 122 supply and fixing in repair gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe of 15 mm bore pipe, including making connections complete all as specified and fixed. 123 supply and fixing in repair ball valves high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore pipe including making connections complete all as as specified and fixed ( minimum weight 20mm 210 gms ) . 124 supply and fixing in repair ball valves high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 25 mm bore pipe including making connections complete all as as specified and fixed ( minimum weight 25mm 455 gms ) . 125 s&f in repair pvc tank coversrequired for 500 ltr to 1000 ltr pvc water tanks complete all as specified and fixed 126 taking up or down steel tubing of 15 mm bore pipe and connections, including cleaning for re fixing or removal to store, complete all as specified and as directed 127 taking up or down steel tubing of 20 mm bore pipe and connections, including cleaning for re fixing or removal to store, complete all as specified and as directed 128 taking up or down steel tubing of 25 mm bore pipe and connections, including cleaning for re fixing or removal to store, complete all as specified and as directed 129 supply and fixing tubes medium grade galvanised, 15 mm bore, isi marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by engineer in charge 130 supply and fixing tubes medium grade galvanised, 20 mm bore, isi marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by engineer in charge. 131 supply and fixing tubes medium grade galvanised, 25 mm bore, isi marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by engineer in charge. 132 supply and fixing fittings for steel tubing galvanised, 15 mm bore, such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc complete all as specified and as directed 133 supply and fixing fittings for steel tubing galvanised, 20 mm bore, such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc complete all as specified and as directed 134 supply and fixing 20 mm nominal outer diachlorinated polyvinyl chloride ( cpvc ) pipes sdr 11, having thermal stability for hot & cold water supply, including all plain cpvc sdr 11 fittings & brass threaded fittings on walls / ceiling or laying in floors, including fixing the pipe with clamps. this includes jointing of pipes & fittings with one step cpvc solvent cement, complete as per direction of engineer in charge. make: supreme, prince, prayag. 135 supply and fixing 25 mm nominal outer diachlorinated polyvinyl chloride ( cpvc ) pipes sdr 11, having thermal stability for hot & cold water supply, including all plain cpvc sdr 11 fittings & brass threaded fittings on walls / ceiling or laying in floors, including fixing the pipe with clamps. this includes jointing of pipes & fittings with one step cpvc solvent cement, complete as per direction of engineer in charge. make: supreme, prince, prayag. 136 m&l cutting chases, pinning in , making good to facings where required and pointing in cement mortar1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting n.exc 10cm girth in brick walls. 137 s&f in repair stainless steel lock grating plain / hole size 100 mmdiaincluding embeding in tiles with white cement. make: jainko, essco, parko. 138 dismantling pvc / cement / ci pipes 50 to 110 mm diaincluding allfittings like bend, branch pieces, connectors, heel rest bend etc and removing from site all as specified and directed 139 supply and fixing upvc ( swr ) type b pipes 110 mm bore single socketed in any length with rubber ringjoints, laid in trenches orin floors, complete all as specified and as directed by engineer in charge. make astral, supreme, finolex 140 supply and fixing upvc ( swr ) type b pipes 110 mm bore single socketed, in any length with rubber ringjoints fixedto walls including stack clamp of gi flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by engineer in charge.make astral, supreme, finolex 141 supply and fixing upvc ( swr ) type b pipes 75 mm bore single socketed in any length with rubber ringjoints, laid in trenches orin floors, complete all as specified and as directed by engineer in charge. make astral, supreme, finolex 142 supply and fixing upvc ( swr ) type b pipes 75 mm bore single socketed, in any length with rubber ringjoints fixedto walls including stack clamp of gi flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by engineer in charge. make astral, supreme, finolex 143 supply and fixing, upvc ( swr ) , bends for75 mm bore , complete all as specified and as directed by engineer in charge.make astral, supreme, finolex 144 supply and fixing, upvc ( swr ) , bends with access doorfor75 mm bore , complete all as specified and as directed by engineer in charge.make astral, supreme, finolex 145 supply and fixing, upvc ( swr ) , bendsfor110 mm borecomplete all as specified and as directed by engineer in charge.make astral, supreme, finolex 146 supply and fixing, upvc ( swr ) , bends with access door, for110 mm borecomplete all as specified and as directed by engineer in charge.make astral, supreme, finolex 147 supply and fixing, upvc branch piece, single ( single y ) with access door for 75 mm bore complete all as specified and directed.make: astral, supreme, finolex. 148 supply and fixing, upvc branch piece, single ( single y ) with access door for 110 mm bore complete all as specified and directed.make: astral, supreme, finolex. 149 supply and fixing, upvc ( swr ) , junction single, ( single t ) with access door equal or unequal for 75 mm bore , complete all as specified and as directed by engineer in charge.make astral, supreme, finolex 150 supply and fixing, upvc ( swr ) , junction single, ( single t ) with access door equal or unequal for 110 mm bore , complete all as specified and as directed by engineer in charge.make astral, supreme, finolex 151 s&f upvc ( swr ) , reducers 110 mm dia complete all as specified. make: astral, supreme, finolex. 152 s&f upvc ( swr ) vent cowl 75 mm dia complete all as specified.make astral, supreme, finolex 153 supply and fixing in repair upvc ( swr ) floor trap plain with gratinghaving dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type b 1 ( 1:2:4 ) complete all as specified and directed.make astral, supreme, finolex 154 s&f in repair, upvc ( swr ) gully trap 125 / 110 mm, setting and jointing with solvent cement complete all as specified.make astral, supreme, finolex 155 rendering 15mm thck in cm 1:3 or plain cement concrete as in sunken floorswithout extra cement on walls / floors and including mixing of water proofing compound ( wpc shall be measured and paid separately ) 156 m&l applying a coat of bituminous primer conforming to is 3384on prepared surface of roof / sunken slab after drying of primer apply app based polymeric membrane minimum weighing 3kg / sqm and minimum 3mm thick reinforced with polyester non woven fabric ( wt not less than 150 gms / sqm ) laid on primed surface by forced torched application and finally apply a coat of hot blown 85 / 25 graded bitumen conforming to is 702 @ 1.2kg / sqm of plaster surface. 157 m&l cement concrete type e 2, 1:5:10 ( 40 mm graded agregate ) in sunkan ( up to 4th floor ) filling and mass concrete complete all as specified and directed by emgr in charge. 158 m&l 40 mm dia g i tubing heavy grade galvanised laid over floors as a spout pipe in sunken floors all as specified. 159 demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable materialfrom the work site ouside defence premises complete all as specified. 160 m&l brick work with subclass b bricks, old size bricks, straight or curved onplan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by engineer in charge 161 m&l brick work with subclass b bricks, old size bricks, straight or curved onplan exceeding 6 metre mean radius built in cement mortar 1:6but except bricks complete all as specified and as directed by engineer in charge 162 m&l brickwork with subclass ‘b’ bricks, straight or curved on plan to any radius in half brick thick walls built in cm 1:4 complete all as specified. 163 material and labour for providing, cement concrete 1:2:4type b 1 ( using 20mm graded aggregate ) , in lintels upto1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed 164 demolition of cement concrete ( unreinforced ) ground floor to 4th floors and pavings n exc 15 cm thickness ( below or above ground level ) and removingthe rubbish from the work site out side defence premises complete all as specified. 165 dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface ( but not backing ) , removing serviceable tiles to store and rubbish off the premises. complete all as specied and directed. 166 roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushingsurface with neat cement slurry with 3.0 kg of cement per sq. metre, removing serviceable tiles to store and rubbish off the cantt area complete all as directed 167 material and labour glazed ceramic coloureddigital tiles in vertical surface300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick cm 1:4 all as specified. ( sample as approved & kept in ges sample room ) 168 material and labournon skid digitalceramicjoint lesscoloured tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured / white cement to match the surface over and including15 mm thick screed bed in cm 1:4. ( sample as approved & kept in ges sample room ) 169 description all as item no 168 but as in vertical surfaces dado / skirting over and including a backing coat of cm 1:4, 10 mm thick complete. 170 material and labourvitrifiedceramic light shade tiles10 mm thick ( square / rectangular ) polishedarea of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured / white cement to matchover and including15 mm thick screed bed in cm 1:4. ( sample as approved & kept in ges sample room ) 171 description all as item no 170 but as in vertical surfaces dado / skirting over and including a backing coat of cm 1:4, 10 mm thick complete. 172 material and labourvitrifiedceramic ( double charged ) edge cutjoint freecoloured or printed any shade tiles10 mm thick ( square / rectangular ) polishedarea of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured / white cement to matchover and including15 mm thick screed bed in cm 1:4. ( sample as approved & kept in ges sample room ) 173 description all as item no 172but as in vertical surfaces dado / skirting over a backing coat of cm 1:4, 10 mm thick complete. 174 material and labour for chequered cement concrete tiles 30cm x30cm x 25mm thick, with greay cement and pigment, set, jointed and pointed in neat cement slurry in floors and laid over and including 20mm thick screed bed in cm 1:4 etc complete all as specified and as directed 175 material and labour for precast factory made interlockingdesigener tiles glazed topmade in white cement and pigment base of thickness not less than 19 mm indifferent colour and pattern ( compressive strength not less than 250 kg / sqcm ) setand jointed in neat cement slurry ( colour and pattern as per sample kept in ge office as approved by ge ) including 15 mm thick screed bedin cm 1:4. completeall as specified and directed by engr in charge. 176 providing and laying 60mm thick factory made chamfered edge cement concrete paver block of m 35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size / shape, made by table vibratory method using pu mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand 177 m&l 16 to 18mm thick granite ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick cm 1:4 as directed by engr in charge. 178 m&l rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified. 179 m&l for 50mm thick cement concrete 1:3:6, type c1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth ( comprising one part hot blown bitumen 85 / 25 and two part of sand ) , complete all as specified and directed. 180 material and labour for precast cement concretelouvers and jallies, 40 mm thick ( 1:2:4 ) type b 0 ( using 12.5 mm graded aggregate ) set in cement mortar 1:6, including all mouldingsand dismantling old u / s broken jallies at site, complete all as specified. 181 m&l for plain cement concrete ( 1:3:6 ) , type c 2 ( using40 mm graded crushed stone aggregate ) nominal mix, 75 mm thick, as in sub base offloors, finished even and faircomplete all as specified and as directed by engineer in charge. 182 m&lfor 25 mm thick cement concrete 1:2:4, type b 0, ( using 12.5 mm graded crushed stone aggregate ) as in sub base / levelling course of floors, finished even and faircomplete all as specified and directed. 183 supply and fixing in repair for bevelled edge mirror of size ( 600x450mm ) , selected quality glass approved size , mounted on 6 mm thick ac building board or commercial plywood and fixed to wooden plugs with ss screws and cup washers. 184 s&f in repair, pvc cabinet mirror ofselected quality glass approved size ( 330mm x 430mm ) , fix with screw complete all as specified. make: prayag, cat no: 551 or equivalent to jaquar, cera 185 supply and fixing in repair sinks made of stainless steel 1.00 mm thick kitchen orlaboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 610mm x 460mm bowl size 560mm x 410mm x 200mm complete with cp waste coupling & pvc waste pipe complete all as specified anddirected by engineer in charge. make: jainko, model no ssj 1. & equivalent in prayag, nirali, jayana. 186 s&f sinks with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm & bowl size 410mm x 355mm x 200mm complete with cp waste coupling & pvc waste pipe complete all as specified anddirected by engineer in charge. make: jainko model no . ssj 8. & equivalent in prayag, nirali, jayana. 187 s & f kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. the over all size ( 30x36x10 ) fixed with steel fastners or steel screw complete.make: jainko, model no.krj 4. and equivalent in prayag, nirali, jayana. 188 dismantling of bricks ( laid flat or on edge ) or brick tiles in floors, channels, kerbs, aprons, etc. ( each layer ) , laid, bedded and pointed in any mortar, complete as specified and directed. 189 complete removal of existing water proofing treatment of any description incl under layer, taking down of cement plaster / demolition of cement concrete any thickness and removal of debris off the premisesincluding grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt / dust. 190 m&l for p.c.c 1:2:4 type b 0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed. 191 m&l rendering 15mm thck in cm 1:4 on concrete surfaces of rooffinished fair & even and including mixing of water proofing compound ( wpc shall be measured and paid separately ) 192 m&lforwater proofing treatment inthe following sequences: ( a ) applying1st course of bituminous primer conforming to is 3384 @ 0.4 kg / sqm cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely ( bi ) applying2nd coat of blown 85 / 25 graded bitumen confirming to is 702 @ 1.2 kg / sqm. ( c ) applying 3rd course of app ( atactic polypropylene ) modified polymeric membrane 3 mm thick weight not less than 3.6 kg / sqm with 160 grams / sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. the membrane has to be laid with lpg torch and overlap sealed and finished neat complete all as specified and as directed. 193 m&l for preparation of newly sufrace of app membrane and applying two coats of water based bituminious alumunium paint @ 200 ml per sqm etc 194 m&l 40mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar ( 1:3 ) mixed with 5% of crude oil by weight of cement on mud phuska 195 cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed by engineer in charge. 196 supply only water proofing compound liquid. 197 cleaning of roof surfaces of rcc roof ( any type ) tiles with brush and removing all vegetation, plants, roots, grass, leaves any type ofmaterial asked to remove at any height of bldg or any part of bldg complete all as directed. 198 m&l for repairing of concrete surfaces such asbalcony, chajjas, upward or downward facias , column, pillar, ceiling and similar items with plain cement concrete 1:2:4type b 0 or rendering 10 15mm thickas per site requirement in cm 1:3 without using extra cement finished even and fair complete all as specified and directed ( up to fourth storey bldgs and including necessory formwork and scaffolding required as per site condition also taking down or dismantling as required at site. 199 m&l for applying two coat of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description having width / girth exceeding 10 cmincluding preparation and rubbing with sand paper to make surface even and smooth complete all as specified. 200 m&l for applying two coat of synthetic enamel paint on new wooden surfaces of any description over a coat of pink primer having width / girth exceeding 10 cm complete all as specified including preparation and necessary filling by chalk putty as and where requered to make surface even and smooth. 201 demolition ofreinforced cement concrete of any discription ground to 4th floors and removingthe rubbish from the work site out side defence premises complete all as specified. 202 m&l for rcc m 15, nominal mix, type b 1 ( 1:2:4 ) , using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specifiedand directed. 203 m&lfor tmtmildsteel bars10mm dia and over, cutto length, bentto shape required, including cranking, bendingspirallyforhooping for column, hookingendandbinding withandincludingmildsteelwire ( annealed ) not lessthan0.9 mm dia or securing with clips, complete all as specified and directed. 204 m&l for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick ( horizontal or sloping ) for rough finished surfaces of concrete, complete all as specified and directed. 205 m&l for use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar workexc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified & directed 206 repair to existing pvc pipe / ci pipe including making the joints water tight by using suitable material including cleaning if requiredand refixingof any dia. note :work to be carried out up to 4th storey bldg in any condition of working place / area 207 material and labour for sealing of wc / floor traps joint and joints between rain water pipe and roofby using neat white cement paste or leak proof material and making the joint leakproof in case seepage is observed from wc / floor trap and joint of rain water pipe and roof slab.note :work to be carried out up to 4th storey bldg in any condition of working place / area 208 taking down carefully aluminium conductor point wiring ( light, fan, light socket, power socket ) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed. 209 m&l for complete point wiringwith 1.5 sqmm single core multi stranded copper conductor frlsh pvc insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible frlsh pvc insulated drawn in and including concealed pvc rigid conduit medium gradeisi marked terminated into gi modular sunken boxes including white cover plate with frame as per relevant isfor mounting moudlar switches, sockets, fan regulators etc complete all as specified and as directed for the following : ( a ) one light / fan point / exhaust fan point controlled by one way switch 6 amps. 210 ( b ) one 3 pin socket outlet 6a point on same board. 211 all as per srl item no 209 above but for one 3 pin socket outlet 15 amp independent with cable of size 2.5 sqmm for point wiring and 2.5 sqmm as in continuous earth wire. 212 s & f moudlar switch piano flush button single pole one way, 6 amp, 1 moudle. complete all as specified and directed. 240 v 213 supply and fix moudlarsocket outlet 2 in 15 pin, 6 amps made of polycarbonate flush type complete all as specified and as directed. 214 supply and fix moudlar socket outlet 2 in 15 pin, 6 & 16 amps flush type made of polycarbonate complete all as specified and as di rected. 215 supply and fix moudlarswitch piano made of polycarbonateflush button single pole one way, 16 amps, 230 / 240 v complete all as specified and as directed by engineer in charge. 216 preparation of old decorated brick / concrete, plastered / un plastered surfaces of walls, pillars, cornices etc ( upto four storey bldgs ) by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots, rubbing with sand paperand applying one coat of lime white wash on the walls, pillars, cornices etc. complete all as specified and directed. 217 preparation of old decorated brick / concrete, plastered / un plastered surfaces of ceilings, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, oil, greasy spots , rubbing with sand paper and applying one coat of white wash on ceiling, complete all as specified and directed. 218 preparation of old decorated brick / concrete / plastered / unplastered surfaces of walls, pillars, cornices etcby booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying one coat of oil emulsion distemper onwalls, pillars, cornices surface including making good uneven surface / holes with birla wall care putty coloured in same shade where ever required etc. complete all as specified and directed. 219 complete removal of existing treatment including washing, rubbing down with sand paper and stopping of distempered and painted surfaces including preparation of old plastered surfaces of walls andapplying two coats of distemperoil emulsion over and including one coat of primerover two coats ofbirla wall care putty 1 to 2 mm thick on plastered surfaces, preparatory to distempering. complete all as specified and as directed by engineer in charge. 220 preparation of old decorated brick / concrete / plastered / unplastered surfaces of walls, pillars, cornices etcby booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying one coat of cement base paint on walls, pillars, cornice etc ( upto 4th storey with necessary scaffolding complete all as specified and directed. 221 preparation of old decorated brick / concrete / plastered / unplastered surfaces of walls, pillars, cornices etcby booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applyingtwo coats of cement base paint on walls, pillars, cornice etc ( upto 4th storey with necessary scaffolding complete all as specified and directed. 222 complete removal of existing treatment including washing, rubbing down with sand paper and stopping ofpainted surfaces including preparation of old plastered surfaces of walls, chajjas, fascia, face of columns, beams etc. andapplyingone coat of weather proof exterior emulsion ( apex ) making good uneven surface / holes with birla wall care putty coloured in same shade where ever required etc ( up to 4th storey with necessary scaffolding ) complete all as specified and directed. 223 preparation of old painted wooden surfaces having width / girth exceeding 10 cm including necessry putty filling with knife of same colour where required to achieve smooth and even surface and applying one coat of synthetic enamel paint on wood surfaces of any description ( up to 4th storey with necessary scaffolding ) complete all as specified and directed 224 preparation of old painted steel surfaces having width / girth exceeding 10 cm including necessry rubbing with sand paper or grinding by hand grinder to achieve smooth and even surface and applying one coat of synthetic enamel paint on steel surfaces of any description ( up to 4th storey with necessary scaffolding ) complete all as specified and directed...

Urban Improvement Trust - Rajasthan

31814282 various civil works and maintenance works in sub division i of division ii b ( arc ) civil work clearing and grubbing road land including uprooting rank vegetation, grass, brush, shrubs, saplings and trees of girth upto 300mm, removal of stumps, disposal of unserviceable material and stacking of serviceable material upto 1000m from road boundary. (morth specification : clause 201).by manual means : in area of light jungle 2 clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared. 3 silt clearance of drains, channels and canals with lift 1.5 mtr. and lead up to 50 mtr. 4 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils 5 add extra over item no. 1.8 and 1.9 (sechedule item no 1) for every additional lift of 1.5 m or part thereof : 6 above 1.50 to 3.00m 7 m 35,60mm thick to be used in light traffic (light traffic is defined as a daily traffic up to 150 commercial vehicles exceeding 30 kn laden weight, or an wquivalent up to 0.5 million standerd axles (msa) for a design life of 20 years (a standerd axle is defind as a single axle load of 81.6 kn ) like pedestrain plazes, shopping complexes ramps, car parks, office drveways , housing colonies , office complexes , rural roads with low volume traffic ,fram houses, beach sites, tourist resorts, local authority footwys ,residential roads, etc. 8 category bdenated only two side like i,z,t shape etc. as per irc sp 63:2004 9 random rubble dry stone kharanja under floor. 10 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 11 m10 grade nominal mix, 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 12 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix 13 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix 14 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix 15 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 16 anti termite treatment of floor using imidacloprid 30.5% ec non repellent, odorless, low dose, environimentally safe terniticide with rapid action non corrosive stain free manufactured by bayer or equivalent company by drilling 12mm diameter holes 300mm apart injecting the emulsion as specified by the manufacturer and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area dpe 12mm dia termitube system with required number of junction boxes are to be installed. the termitube will run all along the perimeter wall both inside and outside. in the middle area the termitube to be installed at an interval of 1.00 mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. after successful testing of termitube, pesticide emulsion of imidacloprid 30.5% ec mixed with water in the ration of 1:474 will be pumped by a motorized spray pump from the junction box in specified manner. the plinth area of the area treated will be measured for payment. 17 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for : 18 columns, pillars, posts and struts etc. 19 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in: 20 cement mortar 1:6 ( 1 cement : 6 sand). 21 cement mortar 1:4 ( 1 cement : 4 sand). 22 cement mortar 1:3 ( 1 cement : 3 sand). 23 random rubble stone masonry with hard stone in superstructure aboveplinth level and upto three levelabove 30cm. thick walls in : 24 cement mortar 1:3 ( 1 cement : 3 sand). 25 cement mortar 1:4 ( 1 cement : 4 sand). 26 cement mortar 1:6 ( 1 cement : 6 sand). 27 pointingonstonemasonryincementsandmortar 1:3 (1 cement : 3 sand) : 28 flush / ruled/ struck or weathered pointing. 29 providing and laying damp proof course with cement concrete grade m 150 (1 : 2 : 4) mortar prepared with 1% solution of water proof compound complete and not applying 2 coats of hot bitumen complete as per specifications. 75mm thick 30 50mm thick 31 75 mm thick 32 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for : 33 suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 34 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. 35 thermo mechanically treated bars (conforming of relevent is code) 36 flyash flyash brick work with flyash flyash bricks of class designation 75 in superstructure above plinth level upto floor three level in all shapes and sizes in : 37 cement mortar 1 : 4 (1 cement : 4 coarse sand) 38 cement mortar 1 : 6 (1 cement : 6 coarse sand) 39 half flyash brick masonry in foundation & plinth using flyash bricks of designation 75 40 cement mortar 1 : 4 (1 cement : 4 coarse sand) 41 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 42 12mm thick. 43 20mm thick. 44 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3 fine sand) 45 making grooves as per design in plaster 10mm to 20mm wide. 46 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 47 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : 48 two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. 49 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. 50 new work 51 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 52 painting with synthetic enamel paint of approved brand and manufacture togive an even shade : 53 two or more coats on new work 54 150cm high fencing with angle iron 50x50x6mm. placed at every 3mtr. apart 30cm. in ground embedded in cement concrete 1:3:6 (30x30x45cm) corner and every tenth post to be strutted with 50x50x6mm. angle iron provided with 6 horizontal lines and two diagonals of black barbed wire between two posts fitted and fixed with g.i. staples including earth work in excavation etc. complete. 55 grading roof for water proofing treatment withwater proffing compound 56 cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 57 providing and fixing pressed steel door frames confirming to is 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike plate and shock absorbers as specified and applyinga coat of approved steel primer after pre treatment of the surface including filling with cc 1:2:4(m15 grade) complete as directed by engineer in charge : 58 profile b 59 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure a: 30 mm thick . 60 decorative teak veneer both side 61 providing and fixingaluminum workfor doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285,fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required pvc/neoprene felt etc. aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing /paneling , c.p. brass/ stainless steel screws al. tower bolt & al. handle & al. aldrop etc.,all complete as per architectural drawings and thedirections of engineer in – charge .(glazing and paneling to be paid for separately). : for fixed portion 62 polyester powder coating aluminum( minimum thickness of powder coating 50 micron) 63 providing and fixing of plastic shutter infill made from extruded multi chamber hollow p.v.c. section having cross section of 200 x 20 x 1 mm and shutter frame made from extrude p.v.c. section in the configuration of double walled c section having an overall cross section of 40 x 37 mm and door fittings such as hinges, aldrop, handles, stopper, locking bolt will be provided. 64 providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (is 1038 1983) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required :partly fixed and partly openable [ fixed area not to exceed 33%] 65 for shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). 66 polyester powder coating aluminum( minimum thickness of powder coating 50 micron) 67 providing and fixing superior quality like hardvyn or equivalent hydraulic door closure. 68 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 300mm x 450mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 69 providing and fixing 1st quality mat finished ceremic tile size 300x300mm confirmingto is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). 70 providing and fixing 15 to 20 mm thick granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12 mm (av.) thick base of cement mortar 1 : 3 (1 cement : 3 coarse sand) jointing with white cement mortar 1 : 2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of : 71 good quality south black above 3601 cm2 slabs 72 extra for providing edge moulding to 15 18mm thick marble/ granite stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. 73 granite work (full edge moulding ) 74 p & f 1st quality heavy duty vitrified glazed mat tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to is 15622 of approved make in all colour and shade, laid with 20 mm thick cm 1: 4 including grounting the joints with white cement and matching pigment etc complete. 75 size600 mm x 1200mm 76 providing & fixingbrown kota/ mandana / dholpur/ slate stone incladding / flooring structuralbase with white cement & tinex chemical& ss clamp and fasteners (of approved brand) laid and jointed with white cement slurry mixed with pigment to match the shade of the slab as per drawing attachedcomplete in all respect as per direction of engineer in charge & architect with all lead & lift. the stone measurement will be done of outer most dimension. thickness of stone 25 30mm. 77 polished blue kota stone flooring skirting, laid over 20 mm thick base of c.m. 1 : 4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete :for area of each slab from 901 to 2000 sq.cm : 78 25 mm thick slab. 79 s/f of fire bricks on edg flooring with fire bricks suitable for 1300 degree centigrade safe working temperature as per is :8 specification laid on & filling of joint by fire resistant mortar/adhesive of required thickness as per directed on a bed of 20 mm thick 1:2 cement mortar of bricks 9 x 4.5x 3 (rate approved year 2008) 80 providing and fixing of glass moisac tiles ( bisseze marke ) size 20 x 20 x 4 mm applied with aaproved adhesive as per specification and direction of engineer in charge 81 providing and fixing staincase railing 90 cm high from nosing of made offollowing specifications. 82 50 mm outer dia (2 mm thick) s.s. pipe hand rail. 83 40 mm outer dia (2 mm thick) s.s. pipe baluster @ 1.00 mtr. 84 4 nos. 20 mm fs. s pipe intermediate runners parallel to hand. 85 s.s. shoe 1.60 mm thick 75 mm outer dia. at each baluster 86 baluster to be welded with s.s. plate 50 mm dia (3 mm thick) anchored in c.c. block with suitable dash fastners 87 50 mm dia & 2 mm thick s.s. pipe for start and end vertical ornamental posts to be provided as per direction of engineer in charge 88 the stainless steel work shall be brushed steel finish with all joints/welds properly grinded to final finish. the stainless steel shall be 304 grade and shall confirm to relevant i.s. 89 providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide.extra if square,rectangular hollow tubularsections are used or grill made by flats only 90 decorative plaster work with spectrum textured coating as per approved colour and shade complete as per manufactures specifications. 91 grit textured @ 2.5 to 3.0 mm thick. 92 ornamental cement plaster in cement sand mortar1 : 4 making kangooras etc. as per jaipurpractice. 93 supplying and fixing machine cutdressed 75 mm pinksand stone (bansi paharpur) dasa/ coping wth ornamental shape having moulding and pan shape engraving as per required pattern with engraving depth of 5 mm (average) in single piece of length 90 cm to be laid on cement mortar 1:4 (12 to 20mm thick) including pointing with admixture of pigment matching with the stone shade. 94 providing corrugated g.s. sheet roofing including vertical / curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces)excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required. 95 0.63 mm thick with zinc coating not less than 275 gm/m2 96 supply & spreading ofgood earth at site complete including loading unloading & transportation etc. 97 supply of dry manure including loading unloading,transportation & stacking at site. 98 farm yard manure(organic) 99 spreading of manure and good earth in required thickness (cost of manure and good earth to be paid separately). 100 laying of lawns including ploughing levelling breaking of clods manuring & removal of stones etc.(cost of manure or extra good earth to be paid seperately) maintenance of lawns for 30 daysor more till the grass forms a thick lawns free from weeds & fit fo 101 in rows 7.5 cms. apart in either direction 102 construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting by vibratory roller 8 10 tonne to meet requirement of table 300 2 including cost of compensation for earth taken from private land with lead upto 1 km as per morth specification : clause no. 305. 103 rough chisel dressed stone flooring over 20 mm (av.) thick base in cm 1 : 6 including pointing with cement mortar 1 : 2 (1 cement : 2 stone dust) with and admixture of pigment to match the shade of stone with joint thickness upto 15 mm : 35 mm thick red sand stone. 104 p & f european type white glazed vitreous china 1st quality double syphonic w.c (is :2556 mark) with p or s trap including cutting and making good the wall and floor 105 p & f indian type white glazed vitreous china 1st quality w.c. orissa pan (is :2556 mark) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor: 106 size 580x440mm. 107 p & f low level flushing cistern of 10 ltr. capacity (is : 2556 mark) o9f approved make with colplete fitting ,c.i. brackets duly painted , brass ball cock with ball, (is :1703 mark)complete including cutting and making good the wall. 108 wvc with c.p. brass bend. 109 p & f wvc wash basin (1st quality, i.s. : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p. pillar cock (is : 8934 mark) &32 mm c.p. brass waste coupling of approved make, 25 mm g.i. waste pipe complete including cutting & making good the wall.: 110 size 550 mm x 400 mm dia for counter top 111 1.0 mm thick salem stainless steel aisi 304 & is 13983 1994kitchen sink of approved make (nirali, neel – kanth, jaina, faber castell )with large waste coupling. 112 (24 x 18 x 8) (20x16x8) 113 p & f inlet connection (angle valves) superior quality, of approved make, for wash basin, gyser etc. 114 c.p. inlet connection 15mm.brass (is : 8931 marked) with 37 cm long pipe and nut. 115 p & f pvc storage tank isi marked (is : 12701) indicating thebis license no),of approved make with cover, 25mm dia 1m long g.i. over flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 116 1000 litres capacity. 117 providing and fixingsuperior quality (jaguar contiental ) cp brassfittings complete as per direction of ei 118 bib cock with long thread 15 mm nominal size 119 brass / gunmetalhalf turnwt. 1 kg.ofapprovedquality / make,25mmnominalbore. 120 p & f full way valve (is:778 mark) or wheel valve of approved make 121 gun metal 32mm nominal bore. 122 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. (concealed work including cutting chases and making good the walls etc.,) 123 20mm nominal outer dia pipes 124 32mm nominal outer dia pipes 125 p&f rigid pvc pipe (is:4985 mark) class ii/ (4 kg. /cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 126 110 mm dia 127 160 mm dia 128 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant: 129 coupler (socket) 130 110mm dia 131 160 mm dia 132 plain tee 133 110mm dia 134 160mm dia 135 door tee 136 110mm dia 137 bend 45 138 110mm dia 139 vent cowel 140 110mm dia 141 door bend (left & right) 142 110mm dia 143 pipe clip 144 110mm dia 145 plain floor trap 146 110mm dia 147 p trap 148 110mm dia 149 socket plug 150 110mm dia 151 door cap 152 110mm dia 153 construction of chamber in all type of soil with 300 mm thick masonry in cm 1:6 m 10 cm thick c.c. 1:5:10 in foundation, 20mm thick insider plaster in cm 1:6, finished with floating neat cement, 50mm thick m 15 grade c.c. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. 154 do size 450 x 450mm depth upto0.5 m cement cover with frame 155 wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) ofapproved make in surface / recessed isi marked medium duty pvc conduit & its accessories, round tiles,hot dipped galvanized modular box with earth terminal, 6 a modular switch,modular plate with grid plate,screws,making connections, testing etc. as required. 156 short point (up to 3 mtr.) 157 medium point (up to 6 mtr.) 158 long point(up to 10 mtr..) 159 wiring of twin control light point with 1.5 sq.mm fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade and 1.5 sq.mm.fr pvc insulated unsheathed flexiable copper earth conductor 1.1 kv grade(is: 694) of approved make in surface/ recessd isi marked medium duty pvc conduit & its accessories, round tiles, 18 swg m.s. box with earthing terminal, 6 amp two way switch, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. 160 medium point (up to 6 mtr) 161 wiring of 3 pin 6 amp light plug point with 1.5 sq.mm fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade and 1.5 sq.mm.fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade(is: 694) of approved make in surface/ recessd isi marked medium duty pvc conduit & its accessories, round tiles, 18 swg m.s. box with earthing terminal, 6 amp switch & 6 amp socket, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. 162 on board 163 medium point (up to 6 mtr) 164 long point (up to 10 mtr) 165 s&f following sizes (dia.) of isi marked medium duty pvc conduit along with accessories in surface / recessed using saddles, clamps, fastener as required includingcutting the wall, covering conduit and making good the same as required. 166 25 mm 167 32 mm 168 50 mm 169 supplying and fixing of power plug point modular accessories on hot dipped galvanized modular on surface or in recessed with suitable size of grid plate with cover plate including cost ofmodular 16 amp. switch and socket outlet, making connection , testing , etc. as required. 170 p&f metal clad industrial plug top & socket unit with pin and sleeve type contact on porcelain/ bakelite base in sheet steel enclosure (without mcb) including making connections, testing etc.as required 171 single / double pole(three pin) 172 32 a 173 providing & fixing isi marked 6 amp bakelite batten/angle holder including making connection testing etc. as required. 174 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor isi marked (is:694) of 1.1 kv grade and approved make in existingsurface or recessed conduit/casing capping including making connections etc. as required. 175 2 x 2.5 sq. mm. + 1x1.5sqmm 176 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 177 p&f 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c/ d tripping characteristic) isi marked is 8828(1996)]/ conforming to iec 60898 in existing board/sheets including making connections, testing etc. as required. 178 single pole mcb 179 6 a to 32 a rating 180 four pole mcb 181 40 a 63 a rating 182 four pole mcb 183 6 a to 32 a rating 184 p&f recessed/ surface mounting heavy duty horizontal type sheet steel distribution board phophatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar,masking sheet, conforming to is13032 & is8623 including making internal dbterminations with copper lugs , testing etc. as required. 185 double door (single phase) 186 12 way 187 double door (three phase) 188 8 way 189 p/laying p.v.c./ xlpe insulated & p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor of is:1554 p i / is :7098 p i of group 1 of approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand,iind class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. 190 25.0 sq.mm 191 4 core 192 50.0 sq.mm 193 120.0 sq,mm 194 3.5 core 195 150.0 sq,mm 196 supplying and making one end termination with heavy duty single compression brass gland sibg type, heavy duty aluminium lugs duly crimped with crimping tool, pvc tape etc for following size of armoured pvc insulated & pvc sheathed/ xlpe aluminium conductor cable of 1100 volt grade as required of size. 197 3.5 x 120.0 sq.mm 198 4 x 25.0 sq.mm 199 p/laying p.v.c./ xlpe insulated & p.v.c. sheathed cable of 1.1 kv grade with copper conductor of is:1554 p i / is :7098 p i of group 1 of approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand,iind class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. 200 10.0 sq.mm 201 4 core 202 supplying and making one end termination with heavy duty single compression brass gland sibg type, heavy duty copper lugs duly crimped with crimping tool, pvc tape etc for following size of armoured pvc insulated & pvc sheathed/ xlpe aluminium conductor cable of 1100 volt grade as required of size. 203 4 x 10.0 sq.mm 204 sitc of wall/ free standing floor mounted dust and vermin proof compartmentalisedcubical panel made out of crca sheet , required hardware,duly treated for derusting in 7 tank process with dephosphating and with powder coating on both side of panel in desired shadethe panel having pu/ neoprene rubber gasket of not less than 3mm thickness , separate detachable gland plate m.s. base channel ,hinged door with locking arrangement for equipment/switchgear. thickness of sheet shallnot be less than 1.6 mm up to 600 mm length / widthof any compartment and be of 2.0 mm above 600 mm. load bearing structure shall beof 2.0 mmthick sheet supported by base m.s. channel if required . side walls and cable alley compartments having bolted type doors with / withoutdetachable extension type structure. (only outer area on all sides shall be measured & panel to be fabricated from cpri approved fabricator) 205 supplying and fixing of aluminium / copper bus barby means of smc / dmc type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. 206 electrolytic grade aluminium bus bar 207 sf of (0 500) v range volt meter on existing panel , making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required. 208 analog type ( 96mm x 96mm ) 209 sf of ct operated direct reading typeampere meter on existing panel , making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required. 210 analog type ( 96mm x 96mm ) 211 below 500 a 212 sf ofcurrent transformer, with all necessary support in existing panel including connection etc. as required . 213 up to 150/5 ratio, 10 va, class 1 accuracy 214 sf of selector switch of 10 a for voltmeter (4 position ) including making connection etc.as required . 215 sf of ct linked selector switch of 10 aforampere meter (4 position ) including making connection etc.as required . 216 sf of110/220 v, led (22.5 mm dia ) indicatinglamp with integral circuit, terminal block, including connection etc. as required. 217 red/yellow/green colour 218 supplying and drawing fr pvc insulated & unsheathed flexiable copper conductor isi marked (is:694) of 1.1 kv grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. 219 1 x 1.5 sq.mm 220 1 x 2.5 sq.mm 221 1 x 4.0 sq.mm 222 1 x 6.0 sq.mm 223 sitc of self healing mpp/mp type shunt capacitor (banks) conforming to is:13340 41 / iec :831 1&2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( psd ) and shall have dissipation factor less than 0.0025 at 50 hz and total wattage loss less than 0.5 watt per kvar . including making connections with suitable capacity conductors/cables testing etc. as required. 224 heavy duty three phase 440 v , 50 hz capacitor (bank) 225 sitc of microprocessor based three phase sensingpower factor correction relay having following sensing capacitysecondary current , self analysing auto c/k setting according to targeted power factor setting, the relay shall havedigit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, indication of switching on units, auto/manual status, and shall have over load protection, no volt release , having multi parameter like kw, kva, kvar,metering facility as required. 226 6 to 8 stage 227 sensitivity upto 50 milli amp 228 p & f ofcam operated rotary switchs on existing panel with 2 way and off postion 229 one pole 230 16 amp 231 p & f of440 volt 3 pole capacitor(ac 6 b ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors/ reactors to limit the inrush current, conforming to is:13947 4 1/iec:947 4 1, din rail mounting type including making connections, testing etc. as required. suitable for following capacity capacitor bank. 232 up to 6 kvar 233 7 to 10 kvar 234 p&f 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c/ d tripping characteristic) isi marked is 8828(1996)]/ conforming to iec 60898 in existing board/sheets including making connections, testing etc. as required. 235 triple pole mcb 236 6 a to 32 a rating 237 p&f on load change over switch, front handle operated, four pole 415 v conforming to is:13947 p iii including connections , testing etc. as required in the following rating: 238 open execution type 239 200 amp 240 sitc of quick make and quick break4 polecurrent limiting mccb having following current rating, short circuitbreaking capacityat 440/415 v, 50 hz; o/l & s/c settings and conforming to is 60947 2 / iec 60947 2 with front face and centralised adjustable, line load interchangeability, having positive isolation capability, provision for uvr , shunt trip ,earth fault trip, push( test) to trip , including making connections with lugs & spreaders,etc. as required. 241 with thermal magnetic release 242 up to 160 amp , 25 ka, adjustable o/l & fixed s/c setting, ics = 100 % icu 243 plate earthing as per is:3043 withcopper earth plate of size 600mm x 600mm x 3.0mm by embodying3 to 4 mtr. below the ground level with 25mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer, nipple ,wire meshed funnel, and c.c.finished chamber covered with hinged type with locking arrangement c.i. cover,c.i. frame of size300mm x 300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required. 244 s & laying following size earth wire/stripin horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required. 245 8 swg copper wire 246 providing & fixing of heavy duty capacitor start 900/1400 rpm single phase isi marked exhaust fan is:2312 marked in existing opening making connections, testing etc. as required 247 300 mm sweep (900/1400 rpm) 248 p & f double ball bearing capacitor start, aluminium body & blade ceilingfanwith down rod up to 30 cm with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. 249 1400 mm sweep 250 p & f of ip 20 led tube light 20 watt with external batten made from crca sheet steel suitable to replace t 8/t 12 tube light, integral driver, 2000 luman + 5% tolerarrce system luman efficiacy of 100 lm/ watt minimum expected life time of 25000 burning hours, cct 5700 k ansi, cri 80, driver efficiency >85%, life expectancy of driver rnin 30000 hrs. pf 0,95 at full load/ 230 volt ac. 251 p & laying xlpe insulated is:7098/ii/85 of group1 and approved make h.t.cable for working voltage 11 k.v.earthed direct in ground including excavation of 30cmx100cm size trench, 25cmlayer of river sand, iind class bricks covering, refilling earth, compaction of earth, making necessary connection testing etc.as required of size. 252 3 core 185.0 sq.mm ...

Urban Improvement Trust - Rajasthan

31814018 various civil works and maintenance works in sub division ii of division ii b ( arc ) civil works clearing and grubbing road land including uprooting rank vegetation, grass, brush, shrubs, saplings and trees of girth upto 300mm, removal of stumps, disposal of unserviceable material and stacking of serviceable material upto 1000m from road boundary. (morth specification : clause 201).by manual means : in area of light jungle 2 clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared. 3 silt clearance of drains, channels and canals with lift 1.5 mtr. and lead up to 50 mtr. 4 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils 5 add extra over item no. 1.8 and 1.9 (sechedule item no 1) for every additional lift of 1.5 m or part thereof : 6 above 1.50 to 3.00m 7 m 35,60mm thick to be used in light traffic (light traffic is defined as a daily traffic up to 150 commercial vehicles exceeding 30 kn laden weight, or an wquivalent up to 0.5 million standerd axles (msa) for a design life of 20 years (a standerd axle is defind as a single axle load of 81.6 kn ) like pedestrain plazes, shopping complexes ramps, car parks, office drveways , housing colonies , office complexes , rural roads with low volume traffic ,fram houses, beach sites, tourist resorts, local authority footwys ,residential roads, etc. 8 category bdenated only two side like i,z,t shape etc. as per irc sp 63:2004 9 random rubble dry stone kharanja under floor. 10 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 11 m10 grade nominal mix, 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 12 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix 13 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix 14 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix 15 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 16 anti termite treatment of floor using imidacloprid 30.5% ec non repellent, odorless, low dose, environimentally safe terniticide with rapid action non corrosive stain free manufactured by bayer or equivalent company by drilling 12mm diameter holes 300mm apart injecting the emulsion as specified by the manufacturer and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area dpe 12mm dia termitube system with required number of junction boxes are to be installed. the termitube will run all along the perimeter wall both inside and outside. in the middle area the termitube to be installed at an interval of 1.00 mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. after successful testing of termitube, pesticide emulsion of imidacloprid 30.5% ec mixed with water in the ration of 1:474 will be pumped by a motorized spray pump from the junction box in specified manner. the plinth area of the area treated will be measured for payment. 17 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for : 18 columns, pillars, posts and struts etc. 19 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in: 20 cement mortar 1:6 ( 1 cement : 6 sand). 21 cement mortar 1:4 ( 1 cement : 4 sand). 22 cement mortar 1:3 ( 1 cement : 3 sand). 23 random rubble stone masonry with hard stone in superstructure aboveplinth level and upto three levelabove 30cm. thick walls in : 24 cement mortar 1:3 ( 1 cement : 3 sand). 25 cement mortar 1:4 ( 1 cement : 4 sand). 26 cement mortar 1:6 ( 1 cement : 6 sand). 27 pointingonstonemasonryincementsandmortar 1:3 (1 cement : 3 sand) : 28 flush / ruled/ struck or weathered pointing. 29 providing and laying damp proof course with cement concrete grade m 150 (1 : 2 : 4) mortar prepared with 1% solution of water proof compound complete and not applying 2 coats of hot bitumen complete as per specifications. 75mm thick 30 50mm thick 31 75 mm thick 32 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for : 33 suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 34 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. 35 thermo mechanically treated bars (conforming of relevent is code) 36 flyash flyash brick work with flyash flyash bricks of class designation 75 in superstructure above plinth level upto floor three level in all shapes and sizes in : 37 cement mortar 1 : 4 (1 cement : 4 coarse sand) 38 cement mortar 1 : 6 (1 cement : 6 coarse sand) 39 half flyash brick masonry in foundation & plinth using flyash bricks of designation 75 40 cement mortar 1 : 4 (1 cement : 4 coarse sand) 41 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 42 12mm thick. 43 20mm thick. 44 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3 fine sand) 45 making grooves as per design in plaster 10mm to 20mm wide. 46 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 47 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : 48 two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. 49 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. 50 new work 51 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 52 painting with synthetic enamel paint of approved brand and manufacture togive an even shade : 53 two or more coats on new work 54 150cm high fencing with angle iron 50x50x6mm. placed at every 3mtr. apart 30cm. in ground embedded in cement concrete 1:3:6 (30x30x45cm) corner and every tenth post to be strutted with 50x50x6mm. angle iron provided with 6 horizontal lines and two diagonals of black barbed wire between two posts fitted and fixed with g.i. staples including earth work in excavation etc. complete. 55 grading roof for water proofing treatment withwater proffing compound 56 cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 57 providing and fixing pressed steel door frames confirming to is 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike plate and shock absorbers as specified and applyinga coat of approved steel primer after pre treatment of the surface including filling with cc 1:2:4(m15 grade) complete as directed by engineer in charge : 58 profile b 59 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure a: 30 mm thick . 60 decorative teak veneer both side 61 providing and fixingaluminum workfor doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285,fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required pvc/neoprene felt etc. aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing /paneling , c.p. brass/ stainless steel screws al. tower bolt & al. handle & al. aldrop etc.,all complete as per architectural drawings and thedirections of engineer in – charge .(glazing and paneling to be paid for separately). : for fixed portion 62 polyester powder coating aluminum( minimum thickness of powder coating 50 micron) 63 providing and fixing of plastic shutter infill made from extruded multi chamber hollow p.v.c. section having cross section of 200 x 20 x 1 mm and shutter frame made from extrude p.v.c. section in the configuration of double walled c section having an overall cross section of 40 x 37 mm and door fittings such as hinges, aldrop, handles, stopper, locking bolt will be provided. 64 providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (is 1038 1983) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required :partly fixed and partly openable [ fixed area not to exceed 33%] 65 for shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately). 66 polyester powder coating aluminum( minimum thickness of powder coating 50 micron) 67 providing and fixing superior quality like hardvyn or equivalent hydraulic door closure. 68 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 300mm x 450mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 69 providing and fixing 1st quality mat finished ceremic tile size 300x300mm confirmingto is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). 70 providing and fixing 15 to 20 mm thick granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12 mm (av.) thick base of cement mortar 1 : 3 (1 cement : 3 coarse sand) jointing with white cement mortar 1 : 2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of : 71 good quality south black above 3601 cm2 slabs 72 extra for providing edge moulding to 15 18mm thick marble/ granite stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. 73 granite work (full edge moulding ) 74 p & f 1st quality heavy duty vitrified glazed mat tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to is 15622 of approved make in all colour and shade, laid with 20 mm thick cm 1: 4 including grounting the joints with white cement and matching pigment etc complete. 75 size600 mm x 1200mm 76 providing & fixingbrown kota/ mandana / dholpur/ slate stone incladding / flooring structuralbase with white cement & tinex chemical& ss clamp and fasteners (of approved brand) laid and jointed with white cement slurry mixed with pigment to match the shade of the slab as per drawing attachedcomplete in all respect as per direction of engineer in charge & architect with all lead & lift. the stone measurement will be done of outer most dimension. thickness of stone 25 30mm. 77 polished blue kota stone flooring skirting, laid over 20 mm thick base of c.m. 1 : 4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete :for area of each slab from 901 to 2000 sq.cm : 78 25 mm thick slab. 79 s/f of fire bricks on edg flooring with fire bricks suitable for 1300 degree centigrade safe working temperature as per is :8 specification laid on & filling of joint by fire resistant mortar/adhesive of required thickness as per directed on a bed of 20 mm thick 1:2 cement mortar of bricks 9 x 4.5x 3 (rate approved year 2008) 80 providing and fixing of glass moisac tiles ( bisseze marke ) size 20 x 20 x 4 mm applied with aaproved adhesive as per specification and direction of engineer in charge 81 providing and fixing staincase railing 90 cm high from nosing of made offollowing specifications. 82 50 mm outer dia (2 mm thick) s.s. pipe hand rail. 83 40 mm outer dia (2 mm thick) s.s. pipe baluster @ 1.00 mtr. 84 4 nos. 20 mm fs. s pipe intermediate runners parallel to hand. 85 s.s. shoe 1.60 mm thick 75 mm outer dia. at each baluster 86 baluster to be welded with s.s. plate 50 mm dia (3 mm thick) anchored in c.c. block with suitable dash fastners 87 50 mm dia & 2 mm thick s.s. pipe for start and end vertical ornamental posts to be provided as per direction of engineer in charge 88 the stainless steel work shall be brushed steel finish with all joints/welds properly grinded to final finish. the stainless steel shall be 304 grade and shall confirm to relevant i.s. 89 providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide.extra if square,rectangular hollow tubularsections are used or grill made by flats only 90 decorative plaster work with spectrum textured coating as per approved colour and shade complete as per manufactures specifications. 91 grit textured @ 2.5 to 3.0 mm thick. 92 ornamental cement plaster in cement sand mortar1 : 4 making kangooras etc. as per jaipurpractice. 93 supplying and fixing machine cutdressed 75 mm pinksand stone (bansi paharpur) dasa/ coping wth ornamental shape having moulding and pan shape engraving as per required pattern with engraving depth of 5 mm (average) in single piece of length 90 cm to be laid on cement mortar 1:4 (12 to 20mm thick) including pointing with admixture of pigment matching with the stone shade. 94 providing corrugated g.s. sheet roofing including vertical / curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces)excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required. 95 0.63 mm thick with zinc coating not less than 275 gm/m2 96 supply & spreading ofgood earth at site complete including loading unloading & transportation etc. 97 supply of dry manure including loading unloading,transportation & stacking at site. 98 farm yard manure(organic) 99 spreading of manure and good earth in required thickness (cost of manure and good earth to be paid separately). 100 laying of lawns including ploughing levelling breaking of clods manuring & removal of stones etc.(cost of manure or extra good earth to be paid seperately) maintenance of lawns for 30 daysor more till the grass forms a thick lawns free from weeds & fit fo 101 in rows 7.5 cms. apart in either direction 102 construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting by vibratory roller 8 10 tonne to meet requirement of table 300 2 including cost of compensation for earth taken from private land with lead upto 1 km as per morth specification : clause no. 305. 103 rough chisel dressed stone flooring over 20 mm (av.) thick base in cm 1 : 6 including pointing with cement mortar 1 : 2 (1 cement : 2 stone dust) with and admixture of pigment to match the shade of stone with joint thickness upto 15 mm : 35 mm thick red sand stone. 104 p & f european type white glazed vitreous china 1st quality double syphonic w.c (is :2556 mark) with p or s trap including cutting and making good the wall and floor 105 p & f indian type white glazed vitreous china 1st quality w.c. orissa pan (is :2556 mark) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor: 106 size 580x440mm. 107 p & f low level flushing cistern of 10 ltr. capacity (is : 2556 mark) o9f approved make with colplete fitting ,c.i. brackets duly painted , brass ball cock with ball, (is :1703 mark)complete including cutting and making good the wall. 108 wvc with c.p. brass bend. 109 p & f wvc wash basin (1st quality, i.s. : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p. pillar cock (is : 8934 mark) &32 mm c.p. brass waste coupling of approved make, 25 mm g.i. waste pipe complete including cutting & making good the wall.: 110 size 550 mm x 400 mm dia for counter top 111 1.0 mm thick salem stainless steel aisi 304 & is 13983 1994kitchen sink of approved make (nirali, neel – kanth, jaina, faber castell )with large waste coupling. 112 (24 x 18 x 8) (20x16x8) 113 p & f inlet connection (angle valves) superior quality, of approved make, for wash basin, gyser etc. 114 c.p. inlet connection 15mm.brass (is : 8931 marked) with 37 cm long pipe and nut. 115 p & f pvc storage tank isi marked (is : 12701) indicating thebis license no),of approved make with cover, 25mm dia 1m long g.i. over flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 116 1000 litres capacity. 117 providing and fixingsuperior quality (jaguar contiental ) cp brassfittings complete as per direction of ei 118 bib cock with long thread 15 mm nominal size 119 brass / gunmetalhalf turnwt. 1 kg.ofapprovedquality / make,25mmnominalbore. 120 p & f full way valve (is:778 mark) or wheel valve of approved make 121 gun metal 32mm nominal bore. 122 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. (concealed work including cutting chases and making good the walls etc.,) 123 20mm nominal outer dia pipes 124 32mm nominal outer dia pipes 125 p&f rigid pvc pipe (is:4985 mark) class ii/ (4 kg. /cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 126 110 mm dia 127 160 mm dia 128 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality / make including joining the pipe with solvent cement rubber ring and lubricant: 129 coupler (socket) 130 110mm dia 131 160 mm dia 132 plain tee 133 110mm dia 134 160mm dia 135 door tee 136 110mm dia 137 bend 45 138 110mm dia 139 vent cowel 140 110mm dia 141 door bend (left & right) 142 110mm dia 143 pipe clip 144 110mm dia 145 plain floor trap 146 110mm dia 147 p trap 148 110mm dia 149 socket plug 150 110mm dia 151 door cap 152 110mm dia 153 construction of chamber in all type of soil with 300 mm thick masonry in cm 1:6 m 10 cm thick c.c. 1:5:10 in foundation, 20mm thick insider plaster in cm 1:6, finished with floating neat cement, 50mm thick m 15 grade c.c. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. 154 do size 450 x 450mm depth upto0.5 m cement cover with frame 155 wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) ofapproved make in surface / recessed isi marked medium duty pvc conduit & its accessories, round tiles,hot dipped galvanized modular box with earth terminal, 6 a modular switch,modular plate with grid plate,screws,making connections, testing etc. as required. 156 short point (up to 3 mtr.) 157 medium point (up to 6 mtr.) 158 long point(up to 10 mtr..) 159 wiring of twin control light point with 1.5 sq.mm fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade and 1.5 sq.mm.fr pvc insulated unsheathed flexiable copper earth conductor 1.1 kv grade(is: 694) of approved make in surface/ recessd isi marked medium duty pvc conduit & its accessories, round tiles, 18 swg m.s. box with earthing terminal, 6 amp two way switch, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. 160 medium point (up to 6 mtr) 161 wiring of 3 pin 6 amp light plug point with 1.5 sq.mm fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade and 1.5 sq.mm.fr pvc insulated unsheathed flexiable copper conductor 1.1 kv grade(is: 694) of approved make in surface/ recessd isi marked medium duty pvc conduit & its accessories, round tiles, 18 swg m.s. box with earthing terminal, 6 amp switch & 6 amp socket, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. 162 on board 163 medium point (up to 6 mtr) 164 long point (up to 10 mtr) 165 s&f following sizes (dia.) of isi marked medium duty pvc conduit along with accessories in surface / recessed using saddles, clamps, fastener as required includingcutting the wall, covering conduit and making good the same as required. 166 25 mm 167 32 mm 168 50 mm 169 supplying and fixing of power plug point modular accessories on hot dipped galvanized modular on surface or in recessed with suitable size of grid plate with cover plate including cost ofmodular 16 amp. switch and socket outlet, making connection , testing , etc. as required. 170 p&f metal clad industrial plug top & socket unit with pin and sleeve type contact on porcelain/ bakelite base in sheet steel enclosure (without mcb) including making connections, testing etc.as required 171 single / double pole(three pin) 172 32 a 173 providing & fixing isi marked 6 amp bakelite batten/angle holder including making connection testing etc. as required. 174 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor isi marked (is:694) of 1.1 kv grade and approved make in existingsurface or recessed conduit/casing capping including making connections etc. as required. 175 2 x 2.5 sq. mm. + 1x1.5sqmm 176 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 177 p&f 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c/ d tripping characteristic) isi marked is 8828(1996)]/ conforming to iec 60898 in existing board/sheets including making connections, testing etc. as required. 178 single pole mcb 179 6 a to 32 a rating 180 four pole mcb 181 40 a 63 a rating 182 four pole mcb 183 6 a to 32 a rating 184 p&f recessed/ surface mounting heavy duty horizontal type sheet steel distribution board phophatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar,masking sheet, conforming to is13032 & is8623 including making internal dbterminations with copper lugs , testing etc. as required. 185 double door (single phase) 186 12 way 187 double door (three phase) 188 8 way 189 p/laying p.v.c./ xlpe insulated & p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor of is:1554 p i / is :7098 p i of group 1 of approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand,iind class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. 190 25.0 sq.mm 191 4 core 192 50.0 sq.mm 193 120.0 sq,mm 194 3.5 core 195 150.0 sq,mm 196 supplying and making one end termination with heavy duty single compression brass gland sibg type, heavy duty aluminium lugs duly crimped with crimping tool, pvc tape etc for following size of armoured pvc insulated & pvc sheathed/ xlpe aluminium conductor cable of 1100 volt grade as required of size. 197 3.5 x 120.0 sq.mm 198 4 x 25.0 sq.mm 199 p/laying p.v.c./ xlpe insulated & p.v.c. sheathed cable of 1.1 kv grade with copper conductor of is:1554 p i / is :7098 p i of group 1 of approved makein ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand,iind class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. 200 10.0 sq.mm 201 4 core 202 supplying and making one end termination with heavy duty single compression brass gland sibg type, heavy duty copper lugs duly crimped with crimping tool, pvc tape etc for following size of armoured pvc insulated & pvc sheathed/ xlpe aluminium conductor cable of 1100 volt grade as required of size. 203 4 x 10.0 sq.mm 204 sitc of wall/ free standing floor mounted dust and vermin proof compartmentalisedcubical panel made out of crca sheet , required hardware,duly treated for derusting in 7 tank process with dephosphating and with powder coating on both side of panel in desired shadethe panel having pu/ neoprene rubber gasket of not less than 3mm thickness , separate detachable gland plate m.s. base channel ,hinged door with locking arrangement for equipment/switchgear. thickness of sheet shallnot be less than 1.6 mm up to 600 mm length / widthof any compartment and be of 2.0 mm above 600 mm. load bearing structure shall beof 2.0 mmthick sheet supported by base m.s. channel if required . side walls and cable alley compartments having bolted type doors with / withoutdetachable extension type structure. (only outer area on all sides shall be measured & panel to be fabricated from cpri approved fabricator) 205 supplying and fixing of aluminium / copper bus barby means of smc / dmc type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. 206 electrolytic grade aluminium bus bar 207 sf of (0 500) v range volt meter on existing panel , making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required. 208 analog type ( 96mm x 96mm ) 209 sf of ct operated direct reading typeampere meter on existing panel , making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required. 210 analog type ( 96mm x 96mm ) 211 below 500 a 212 sf ofcurrent transformer, with all necessary support in existing panel including connection etc. as required . 213 up to 150/5 ratio, 10 va, class 1 accuracy 214 sf of selector switch of 10 a for voltmeter (4 position ) including making connection etc.as required . 215 sf of ct linked selector switch of 10 aforampere meter (4 position ) including making connection etc.as required . 216 sf of110/220 v, led (22.5 mm dia ) indicatinglamp with integral circuit, terminal block, including connection etc. as required. 217 red/yellow/green colour 218 supplying and drawing fr pvc insulated & unsheathed flexiable copper conductor isi marked (is:694) of 1.1 kv grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. 219 1 x 1.5 sq.mm 220 1 x 2.5 sq.mm 221 1 x 4.0 sq.mm 222 1 x 6.0 sq.mm 223 sitc of self healing mpp/mp type shunt capacitor (banks) conforming to is:13340 41 / iec :831 1&2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( psd ) and shall have dissipation factor less than 0.0025 at 50 hz and total wattage loss less than 0.5 watt per kvar . including making connections with suitable capacity conductors/cables testing etc. as required. 224 heavy duty three phase 440 v , 50 hz capacitor (bank) 225 sitc of microprocessor based three phase sensingpower factor correction relay having following sensing capacitysecondary current , self analysing auto c/k setting according to targeted power factor setting, the relay shall havedigit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, indication of switching on units, auto/manual status, and shall have over load protection, no volt release , having multi parameter like kw, kva, kvar,metering facility as required. 226 6 to 8 stage 227 sensitivity upto 50 milli amp 228 p & f ofcam operated rotary switchs on existing panel with 2 way and off postion 229 one pole 230 16 amp 231 p & f of440 volt 3 pole capacitor(ac 6 b ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors/ reactors to limit the inrush current, conforming to is:13947 4 1/iec:947 4 1, din rail mounting type including making connections, testing etc. as required. suitable for following capacity capacitor bank. 232 up to 6 kvar 233 7 to 10 kvar 234 p&f 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c/ d tripping characteristic) isi marked is 8828(1996)]/ conforming to iec 60898 in existing board/sheets including making connections, testing etc. as required. 235 triple pole mcb 236 6 a to 32 a rating 237 p&f on load change over switch, front handle operated, four pole 415 v conforming to is:13947 p iii including connections , testing etc. as required in the following rating: 238 open execution type 239 200 amp 240 sitc of quick make and quick break4 polecurrent limiting mccb having following current rating, short circuitbreaking capacityat 440/415 v, 50 hz; o/l & s/c settings and conforming to is 60947 2 / iec 60947 2 with front face and centralised adjustable, line load interchangeability, having positive isolation capability, provision for uvr , shunt trip ,earth fault trip, push( test) to trip , including making connections with lugs & spreaders,etc. as required. 241 with thermal magnetic release 242 up to 160 amp , 25 ka, adjustable o/l & fixed s/c setting, ics = 100 % icu 243 plate earthing as per is:3043 withcopper earth plate of size 600mm x 600mm x 3.0mm by embodying3 to 4 mtr. below the ground level with 25mm dia. g.i. b class watering pipe including all accessories like nut, bolts, reducer, nipple ,wire meshed funnel, and c.c.finished chamber covered with hinged type with locking arrangement c.i. cover,c.i. frame of size300mm x 300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required. 244 s & laying following size earth wire/stripin horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required. 245 8 swg copper wire 246 providing & fixing of heavy duty capacitor start 900/1400 rpm single phase isi marked exhaust fan is:2312 marked in existing opening making connections, testing etc. as required 247 300 mm sweep (900/1400 rpm) 248 p & f double ball bearing capacitor start, aluminium body & blade ceilingfanwith down rod up to 30 cm with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. 249 1400 mm sweep 250 p & f of ip 20 led tube light 20 watt with external batten made from crca sheet steel suitable to replace t 8/t 12 tube light, integral driver, 2000 luman + 5% tolerarrce system luman efficiacy of 100 lm/ watt minimum expected life time of 25000 burning hours, cct 5700 k ansi, cri 80, driver efficiency >85%, life expectancy of driver rnin 30000 hrs. pf 0,95 at full load/ 230 volt ac. 251 p & laying xlpe insulated is:7098/ii/85 of group1 and approved make h.t.cable for working voltage 11 k.v.earthed direct in ground including excavation of 30cmx100cm size trench, 25cmlayer of river sand, iind class bricks covering, refilling earth, compaction of earth, making necessary connection testing etc.as required of size. 252 3 core 185.0 sq.mm ...

Department Of Local Bodies - Rajasthan

31810325 civil work for auditorium for nagar parishad, dausa, rajasthan civil work for auditorium for nagar parishad, dausa, rajasthan earth workclearing grass and removal of rubbish (maximum 150mm) by manual means and disposal at a lead of 50 metres as per mort&h specification clause 201. 2 earth work in excavation in open area, stp, wtp, pumping station with mechanical means including dressing of sides and ramming of bottoms, including getting out the excavated material, disposal of excavated material lead upto 1000m at suitable site as per as per drawing and as per direction of engineer. (measurements for payment to be done as per standard drawings). in all type of soil. upto 3.0 m depth. 3 earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of engineer for following depths, below natural ground / road top level. in all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc. depth upto 1.5 m. 4 add extra for over all depth of excavation above 1.5 m and upto 3.0 m over item no 4.10.1.1 5 in ordinary rock. depth upto 1.5 m. 6 add extra for over all depth of excavation above 1.5 m and upto 3.0 m over item no 4.10.2.1 7 carriage of materials by mechanical transport including loading, unloading and stacking ::upto 1 km 8 stone, boulders, gravelly materia 9 earth filling with available surplus soil excavated from foundations and taken only from outside of building plinth in layers not exceeding 20cm in depth, consolidating each deposited layer including ramming and watering and consolidation with lead up to 50 m and lift upto 1.5 m. 10 diluting and injection chloropyrifos emulsifiable concentrate 20% with 1% concentration for pre constructional anti termite treatment as per is 6313 part iii as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which approach is to be laid surrounding of pipes and conduits etc. complete as per specification (plinth floor area only shall be measured for payment and excluding the cost of chemical emulsion). 11 providing and laying of filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2. of mort&h specifications with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specification including all material, labour, machinery as per clause 710.1.4 of irc:78 and clause 2200 of mort&h specification. 12 concrete work 13 providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work upto plinth level 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 14 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. 15 reinforced cement concrete 16 providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement all work upto plinth level 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size). (as per design mix). 17 reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto two stories excluding cost of centring, shuttering, finishing and reinforcement :1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) (as per design mix) 18 reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto two stories excluding the cost of centring, shuttering, finishing and reinforcement: m 30 grade concrete. 19 reinforced cement concrete work in arches, arch ribs, domes, vaults, shells, folded plate and roofs having slope more than 15° upto two stories excluding the cost of centring, shuttering, finishing and reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 20 providing and laying upto two stories reinforced cement concrete in kerbs, steps and the like excluding the cost of centring, shuttering, finishing and reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 21 add extra for laying reinforced cement concrete above two stories (or 7.50 mtr height above plinth level) for every one storey or 3.00 m height or part thereof. 22 centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete. 23 walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. 24 suspended floors, roofs, landings, balconies and access platform. 25 lintels, beams, plinth beams, girders, bressumers and cantilevers. 26 columns, pillars, piers, abutments, posts and struts.22.1.5 27 stairs, (excluding landings) except spiral staircases. 28 extra for shuttering in circular work (20% of respective centring and shuttering items). 29 edges of slabs and breaks in floors and walls. under 20 cm wide. 30 weather shade, chajjas, corbels etc., including edges. 31 add extra for doing centering and shutteriing work for every additional height of 1 metre or part thereof beyond initial 7.5 metre height from plinth level. 32 reinforcement for r.c.c. work at all levels including straightening, cutting, bending, placing in position and binding all complete. thermo mechanically treated bars. 33 brick / stone masonery work 34 brick work with fps bricks of class designation 75 in foundation and plinth in cement mortar 1:4 (1 cement : 4 coarse sand). 35 brick work with fps bricks of class designation 75 in superstructure above plinth level upto two stories in all shapes and sizes in cement mortar 1:4 (1 cement : 4 coarse sand). 36 half brick masonry with fps bricks of class designation 75 in superstructure above plinth level upto two stories. cement mortar 1:3 (1 cement :3 coarse sand). 37 extra for providing and placing in position 2 nos. 6mm dia. m.s. bars at every third course of half brick masonry. 38 random rubble stone masonry work in cement mortar with mechanical mixer in foundation (at any level) complete as per drawing and technical specification and as per clause 1000 and 1400 of mort&h specification including all scaffolding material, labour, machinery but excluding pointing and plastering. in cement mortar 1:4 (1 cement : 4 coarse sand). 39 providing and fixing granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12mm (av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. green / black above 3601 cm2 slabs. 40 extra for providing edge moulding to 15 18mm thick marble/ granite stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. granite/kota stone work. moulding. 41 extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete 42 providing and fixing 1st quality mat finished ceremic tile size 300x300mm confirming to is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). 43 extra for using marble printed / granite shade or dark shade tiles instead of white, grey, ivory, fume red brown, light green, light blue and other light shades in glazed tiles and mat finished tiles 44 providing and fixing motive pieces all coloures for glazed tiles laid over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white mixed with pigment of matching shade complete. size 200 x 300mm. 45 p & f 1st quality vitrified porcelain polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to is 15622 of approved make in all colour and shade, laid with 20 mm thick cm 1 : 4 including grounting the joints with white cement and matching pigment etc complete. size 600 mm x 600 mm. 46 providing and fixing 1st quality mat & glossy finished ceramic tiles colour such as standard white, grey, ivory, fume, red brown, light green, light blue, and other light shades with water absorbtion less than or equal to 0.08% confirming to is : 13753 & is : 15622 in floor, steps etc laid on bed on neat cement slury finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the the cost of cement mortar bed 1:4) size 300mm x 450mm. 47 providing and fixing 1st quality ceramic glazed vitrified tiles of colour standard white, grey, ivory, fume, red brown, light green, light blue, and other light shades with water absorbtion less than or equal to 0.08% confirming to is : 13753 & is : 15622 in floor, steps etc laid on bed on neat cement slury finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete. (excluding the the cost of cement plaster on wall and pillar). size 600mm x 1200mm 48 38mm thick wood block flooring of first class teak wood laid over 25mm thick levelling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10mm nominal size) to be paid separately coated with a thin layer of hot bitumen (blown type) @ 2.45 kg per sqm. including fixing blocks in position after dipping in hot bitumen (blown type) upto half depth, planed, levelled smooth and finished complete. 49 kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 50 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. red sand stone. 51 extra for pre finished nosing in treads of steps of kota stone/ sand stone slab. 52 roofing 53 providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design in 75x75mm deep chase. 54 providing corrugated g.s. sheet roofing including vertical/ curved surface fixed with polymer coated j or l hooks, bolts and nuts 8 mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.80mm thick with zinc coating not less than 275gm/m². 55 extra for circular cutting in c.g.s. sheet roofing for making opening of area exceeding 40 square decimetre 0.80 mm thick 56 providing and fixing 15 cm wide 45 cm over all semi circular plain g.s. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes complete. 0.80mm thick with zinc coating not less than 275gm/m² 57 cement plastering including t&p, scaffolding, material and complete labpour, including cost of water, curing, racking of joints etc. with 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement : 4 fine/ coarse sand) 58 cement plastering including t&p, scaffolding, material and complete labpour, including cost of water, curing, racking of joints etc. with 20 mm cement plaster of mix : 1:4 (1 cement : 4 fine/ coarse sand). 59 cement plastering including t&p, scaffolding, material and complete labpour, including cost of water, curing, racking of joints etc. with 6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of lime wash on top of walls when dry for bearing of r.c.c. slabs and beams. 60 extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. 61 18 mm thick moulded cement mortar band in two coats under layer 12mm thick with cement mortar 1:5 (1 cement : 5 coarse sand) toplayer 6mm thick with cement mortar 1:4 (1 cement : 4 fine sand). design on outer plaster. 62 extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 63 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: two or more coats on new work. 64 finishing walls with acrylic smooth exterior paint of required shade new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). 65 painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work. 66 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete 67 providing and fixing thermal insulation with resin bonded fibre glass wool conforming to is : 8193, density 16kg/m3 , 50mm thick, wrapped in 200g virgin polythene bags placed over existing false ceiling and held in position by criss crossing gi wire. 68 providing and fixing machine moulded aluminium covering of approved pattern & design, made out of machine cut aluminium sheet and machine holed for receiving screws, over expansion joints on vertical surfaces/ceilings with full threaded, cadmium plated steel screws 4mm dia. stem, 30mm long and aluminium washers 2mm thick, 15mm dia. at a staggered pitch of 200mm centre to centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. complete. powder coated aluminium sheet 2.5mm thick (minimum thickness of powder coating 50 micron). 69 filling the gap in between aluminium frame & adjacent rcc/ brick/ stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of engineer in charge complete. upto 5mm depth and 5 mm width. 70 providing and laying expansion joint complete as per drawing and technical specification and as per clause 2605 of mort&h specification including all material, labour, machinary etc. 71 fillar joint with 20m thick compressible fibre board. 72 fillar joint with joint sealing compound with coarse sand and 6 %bitumen by weight. 73 structural steel work riveted,bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete: hot finished seamless type tubes. 74 providing and fixing t iron frames for doors, windows and ventilators of mild steel tee sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or with dash fastener or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 75 providing and fixing pressed steel door frames confirming to is: 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre treatment of the surface as directed by engineer in charge: profile c 76 providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing including applying a priming coat of approved steel primer. m.s. tube. 77 providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rail of t iron 40x40x6mm with 40mm dia, steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. 78 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesin in glue both sides including approved isi marked stainless steel butt hinges fittings with necessary screws complete as per annexure a : 30 mm thick decorative teak veneer both side. 79 extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (over all area of door shutter to be measured). decorative teak veneer both side. 80 extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) rectangular or square. 81 extra for cutting rebate in flush door shutters for making double leaf shutter(total area ofthe shutter to be measured). 82 providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised m.s. screws including drilling holes in masonry work /cc/ r.c.c. and making good etc. complete. 50 mm long. 83 providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with c.p. brass screws and wooden plugs, etc., wherever necessary complete: 20 mm dia. 84 providing and fixing to existing door frames. 30mm thick factory made solid both side pre laminated panel pvc door shutter consisting of frame made out of m.s. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top & bottom rails. m.s. frame shall have a coat of steel primers of approved make and manufacture. m.s. frame covered with 5mm thick heat moulded pre laminated pvc c channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45degree angle on either side forming styles; and 5mm thick, 95mm wide pvc sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide pvc sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. top, bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2 ) thick, 20mm wide cross pvc sheet be provided as gap insert for top rail & bottom rail. paneling of 5mm thick both side pre laminated pvc sheet to be fitted in the m.s. frame welded/ sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide pvc sheet beading on inner side, and joined together with solvent cement adhesive. an additional 5mm thick pvc strip of 20mm width is to be stuck on the interior side of the c channel using pvc solvent adhesive etc. complete as per direction of engineer in charge. manufacturer’s specification & drawing (for w.c. and bathroom door shutter). 85 aluminium work 86 providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required pvc/neoprene felt etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. (glazing and panelling to be paid for separately) : for fixed portion. anodised aluminium (anodised transparent or dyed to required shade according to is: 1868, minimum anodic coating of grade ac 15). 87 for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of pvc / neoprene gasket required (fittings shall be paid for separately). powder coated aluminium (minimum thickness of powder coating 50 micron). 88 providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood pre laminated one side decorative lamination on other side balancing lamination grade i, type ii, is : 12823 marked including priming coat on unexposed surface, with necessary fixing arrangement and screws etc. complete : 25 mm thick 89 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with pvc/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer incharge . (cost of aluminium snap beading shall be paid in basicitem) : with float glass panes of 5.50 mm thickness. 90 providing and fixing double action hydraulic floor spring of approved brand and manufacture is : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece m.s. sheet outer box with slide plate etc. complete as per the direction of engineer in charge. with stainless steel cover plate. 91 providing and fixing stainless steel (ss 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of engineerin charge complete. 355 x 19 mm. 92 interior work 93 false ceiling 94 providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from m.s. sheet and galvanised in accordance with zinc coating of grade 350 as per is : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to g.i. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to g.i. channel with connecting clips made out of 2.64mm diax230mm long g.i. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the engineer in charge but excluding the cost of painting with 12.5 mm thick tapered edge gypsum board conforming to is: 2095 part i, 95 sanitary items 96 plumbing 97 providing and fixing unplasticised p.v.c. connection pipe with ptmt nuts collar and bush of approved quality and colour. 98 15 mm nominal bore with 3 cm length. 99 15 mm nominal bore with 45 cm length. 100 providing and fixing ptmt ball cock of approved quality, colour and make complete with epoxy coated aluminium rod with l.p./ h.p.h.d. plastic ball.20 mm nominal bore, 120 mm long. weighing not less than 198 gms. 101 providing and fixing ball valve (brass) of approved quality, high or low pressure, with plastic floats complete : 102 15 mm nominal bore 103 20 mm nominal bore 104 25 mm nominal bore 105 providing and fixing gun metal non return valve of approved quality (screwed end) : 106 25 mm nominal bore horizontal 107 25 mm nominal bore vertical 108 providing and placing on terrace (at all floor levels) polyethylene water storage tank isi : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 109 sanitary 110 providing and laying flanged c.i. standard specials such as tees, bends, collars, tapers, caps etc., suitable for flanged jointing as per is : 1538 : upto 300 mm dia. 111 providing and laying s&s centrifugally cast (spun) iron pipes (class la) conforming to is 1536 : 112 100 mm dia. pipe 113 125 mm diameter pipe 114 providing lead caulked joints to spun iron or c.i. pipes and specials including testing of joints but excluding the cost of pig lead : 115 100 mm diameter pipe 116 125 mm diameter pipe 117 supplying pig lead at site of work. 118 providing, laying and jointing glazed stoneware pipes grade ‘a’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 200 mm diameter 119 constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) r.c.c. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : 120 inside size 90x80 cm and 45 cm deep including c.i. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : with bricks with class designation 75 121 inside size 120x90 cm and 90 cm deep including c.i. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : with bricks class designation 75 122 providing and fixing square mouth s.w. gully trap grade a’ complete with c.i. grating brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 100x100 mm size p type with bricks class designation 75. 123 constructing brick masonry road gully chamber 45x45x77.5 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast r.c.c. vertical grating complete as per standard design with bricks. 124 constructing brick masonry road gully chamber 110x50x77.5 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast r.c.c. horizontal grating with frame and vertical grating complete as per standard design with bricks 125 fixtures 126 providing and fixing white vitreous china pedestal type water closet (european type) with seat and lid, 10 litre low level white vitreous china flushing cistern & c.p. flush bend with fittings & c.i. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid. 127 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps,32 mm c.p. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : white vitreous china surgeon type wash basin of size 660x460 mm with a pair of 15 mm c.p. brass pillar taps with elbow operated levers. 128 providing and fixing kitchen sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required : white glazed fire clay kitchen sink of size 600x450x250 mm. 129 providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 130 rectangular shape 453x357mm 131 rectangular shape 1500x450 mm 132 providing and fixing 100 mm sand cast iron grating for gully trap 133 providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 134 providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors 100 mm inlet and 100 mm outlet 135 providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931. 15 mm nominal bore 136 providing and fixing ptmt soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements. weighing not less than 106 gms. 137 providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50 cm deep and 1.8 cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of engineer incharge and finished smooth. granite stone of approved shade 138 providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. 139 providing and fixing g.i. pipes complete with g.i. fittings and clamps, including cutting and making good the walls etc. 140 internal work exposed on wall 15 mm dia. nominal bore 141 internal work exposed on wall 20 mm dia. nominal bore 142 internal work exposed on wall 25 mm dia. nominal bore 143 internal work exposed on wall 32 mm dia. nominal bore 144 concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall. 15 mm dia. nominal bore 145 concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall. 20 mm dia. nominal bore 146 providing and fixing g.i. pipes complete with g.i. fittings including trenching and refilling etc. external work : 147 15 mm dia. nominal bore 148 20 mm dia. nominal bore 149 25 mm dia. nominal bore 150 32 mm dia. nominal bore 151 painting g.i. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work : 152 15 mm dia. nominal bore 153 20 mm dia. nominal bore 154 25 mm dia. nominal bore 155 32 mm dia. nominal bore 156 painting g.i. pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality : 157 15 mm dia. nominal bore 158 20 mm dia. nominal bore 159 25 mm dia. nominal bore 160 32 mm dia. nominal bore 161 providing and fixing g.i. union in g.i. pipe including cutting and threading the pipe and making long screws etc. complete (new work) 162 15 mm nominal bore 163 20 mm nominal bore 164 25 mm nominal bore 165 water harvesting system 166 construction of tube well upto 100 meter depth and above in all type of rocks by dth system and over burden to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes but excluding cost of casing pipes as per is : 2800 (part i & ii) 1979 specifications. the work would be completed after obtaining sand free water. the tube well should have a throughout bore as per nominal dia of casing pipe: 200 mm dia nominal bore 167 supply of strainer pipes made of erw m.s. black pipe isi mark of following sizes at the site of work including required size of slotting as per is:8110 1985 of following nominal bore sizes at site of work. 200 mm dia 168 supply and fixing of m.s. clamp set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. 169 providing & lowering of g.i. flange pipe b class including rubber washer and nuts of 8 mm dia complete in all respect. 50 mm dia 170 development of tube well as per is specification using suitable compressor to give sand free water for required yield of the gravel packed tube well. 171 electrical g schedule 172 wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) ofapproved make in surface / recessed isi markedmms ( is:9537 p iii ) pvc conduit & its accessories, round tiles,18 swg m.s. box with earth terminal, 6 a switch, 3.0 mm thick isi marked phenolic laminated sheet, zinc plated / brassscrews, cup washers, making connections, testing etc. as required. 173 short point (up to 3 mtr.) 174 medium point (up to 6 mtr.) 175 long point(up to 10 mtr..) 176 wiring of twin control light / fan / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) of approved make in surface / recessed isi marked mms ( is:9537 p iii ) pvc conduit & its accessories, round tles,18 swg m.s. box with earth terminal, 6 a two way switch, 3.0 mm thick isi marked phenolic laminated sheet, zinc plated / brassscrews, cup washers, making connections, testing etc. as required. 177 short point (up to 3 mtr.) 178 medium point (up to 6 mtr.) 179 long point(up to 10 mtr..) 180 wiring of 3 pin 6 amp. light plug point with 1.5 sq. mm fr pvc insulated unsheathed 1.1 kv grade flexible copper conductor and 1.5 sq.mm fr pvc insulated unsheathed 1.1 kv grade copper earth conductor (is:694) of approved make double lock/ isi marked single lock pvc casing capping & its accessories, 18 swg m.s. box with earth terminal, screwless cage connectors for neutral looping in switch board & falce ceiling point, 6 a switch, 6 a socket, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. 181 on board 182 short point (up to 3 mtr.) 183 medium point (up to 6 mtr.) 184 long point(up to 10 mtr..) 185 s&f following sizes (dia.) of isi marked medium duty pvc conduit along with accessories in surface / recessed using saddles, clamps, fastener as required including cutting the wall and making good the same as required. 186 20 mm 187 25 mm 188 32 mm 189 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor isi marked (is:694) of 1.1 kv grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. 190 3x 1.5 sq.mm 191 2 x 2.5 sq. mm. + 1x1.5sqmm 192 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 193 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. 194 4 x 10.0 sq.mm 195 4 x 16.0 sq.mm 196 supplying and drawing pvc jacketed with annealed bare copper inner conductor & tinned copper conductor shielding foam pe dielectric coaxial cable of approved make in existingsurface or recessed conduit/casing capping including making connections as required. 197 rg 6 198 rg 11 199 supplying and drawing pvc/ polythene insulated and pvc sheathed unarmoured/ armoured telephone cable with 0.5 mm dia. tinned / annealed copper conductor taped &confirming to itd specification s/ws 112c &113 c of approved make in existing surface or recessed conduit/casing capping. 200 unarmoured 2 pair 201 unarmoured 10 pair 202 unarmoured 20 pair 203 unarmoured 50 pair 204 jelly filled armoured (pijf) 5 pair 205 jelly filled armoured (pijf) 10 pair 206 jelly filled armoured (pijf) 20 pair 207 jelly filled armoured (pijf) 50 pair 208 p&f recessed/ surface mounting heavy duty horizontal type sheet steel distribution board phophatised/ powder painted complete with copper bus bar, shorting link , neutral link, earth link and din bar masking sheet conforming to is13032 & is8623 including making internal db terminations with copper lugs , testing etc. as required. double door (three phase) per phase isolation 209 2+8 way 210 2+12 way 211 providing & laying xlpe insulated / p.v.c. sheathed cable of 1.1 kv grade with aluminium conductor armoured of is:7098 i/1554 1 approved make in ground as per is:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. 212 2.5 sq. mm 4 core 213 4.0 sq.mm 4 core 214 6.0 sq.mm 4 core 215 10.0 sq.mm 4 core 216 16.0 sq.mm 4 core 217 25.0 sq.mm 3.5 core 218 35.0 sq.mm 3.5 core 219 50.0 sq.mm 3.5 core 220 70.0 sq,mm 3.5 core 221 95.0 sq.mm 3.5 core 222 120.0 sq.mm 3.5 core 223 150.0 sq.mm 3.5 core 224 240.0 sq.mm 3.5 core 225 300.0 sq.mm 3.5 core 226 supplying and making one end termination with heavy duty single compression brass gland sibg type, heavy duty aluminium lugs duly crimped with crimping tool, pvc tape etc for following size of armoured pvc insulated & pvc sheathed/ xlpe aluminium conductor cable of 1100 volt grade as required of size. 227 3.5 x 25.0 sq.mm 228 3.5 x 35.0 sq.mm 229 3.5 x 50.0 sq.mm 230 3.5 x 70.0 sq.mm 231 3.5 x 95.0 sq.mm 232 3.5 x 120.0 sq.mm 233 3.5 x 150.0 sq.mm 234 3.5 x 240.0 sq.mm 235 3.5 x 300.0 sq.mm 236 4 x 2.5 sq.mm 237 4 x 4.0 sq.mm 238 4 x 6.0 sq.mm 239 4 x 10.0 sq.mm 240 4 x 16.0 sq.mm 241 supply, fabricating & installing following sizes of perforated cable trays including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling with suspenders and including painting as required. hot dipped galvanized. 242 150mm x 50mm x 1.6mm 243 300mm x 50mm x 1.6mm 244 450mm x 50mm x 2.0mm 245 600mm x 50mm x 2.0mm 246 maintenance free gel earthing with pipe in pipe /strip in pipe technology filled with anti corrosive conductive compound (cpri tested) below the ground in 150 200 mm dia earth pit and surrounding filled with required mineral filling compound (mfc should have hygroscopic proper ty to retain the moisture for long time to create low resistance zone) and c.c. finished chamber covered with hinge type with locking arrangement c.i cover. c.i. frame of size 300mm x300mm complete testing of earth resistance as required of following sizes with pipe in pipe technology (inner pipe dia / outer pipe dia) 80 100 micron g.i. coating with pipe in pipe technology with 80 100 micron g.i. coating g.i. pipe 3000 mm long , 80/40 mm , terminal 14 mm g.i. strip 247 s & laying following size earth wire/stripin horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required. 248 8 swg copper wire 249 25mm x 3mm copper strip 250 50mm x 6mm copper strip 251 25mm x 3mm g.i. ( hot dipped) strip 252 25mm x 6mm g.i. ( hot dipped) strip 253 p & f of ip20 led recessed/ surface mounted round/ sqaure non dimmable downlight with die cast aluminum housing & heat sink for heat dissipation, high purity reflector with external driver having efficiency > 85% and in compliance to iec standards. ( supplied together with luminaire) power consumption of =< 7w/10w/8w/12w/15w/18w with 100/500/750/1100/1250 lumens, system lumen, efficeancy of 70 lm / watt or 100 lm / watt output suitable to replace 1x18w/ 2x18w/2x26w cfl downlights, life time of 50000 burning hours with 70% of intial lumen maintained. cct 3000° k, 4000° k and 6000° k. fixture shall be ce compliance. 254 recessed mounting led downlight 18/20w 255 surface mounting led downlight 18/20w 256 p & f of ip20 led ceiling/ recessed/ suspended mounting light fixture made form crca sheet steel housing, high purity/ transmisivity diffuser for uniform light distrubution.high efficiency driver electronics having efficiency > 85% and in compliance to iec standards.(integral driver). power consumption of 40 w/50w/60w, 3000/3300/4200 lumens, system lumen efficiency of 70 80 lm / watt output suitable for 2x36w ftl/ 2x36w cfl/3x36w cfl light fixtures, life time of 50000 burning hours with 70% intial lumens maintained. cct 3000° k, 4000° k and 6000° k. fixture shall be ce compliance. surface mounting 36w led light 2’x2’ with acrylic/ prismatic front cover 257 p & f energy efficient direct fit (retrofit) led tube system (with integral driver), on existing fixture. power consumption of18w / 36w 1500 3000 lumens, system lumen efficiency 80 lm/watt output, life time of 50,000 burning hours with 70% initial lumen maintained. cct 3000°k, 4000°k& 6000°k. 4 led tube shape fixture 18w. 258 p/ f ip 65/ ip 66 protected street light luminaries on existing bracket. fixture made from powder coated single piece pressure die cast aluminum housing with heat dissipation fins on housing with high power leds . diffuser / glass cover for ensuring ip 65 protection for lamp and control gear compartment, system lumen output of 100 lum/watt high power led. integrated driver shall be high efficiency having efficiency more than 85 % and in compliance to iec standards. system life of 50000 burning hours with 70 % of initial lumens maintained. fixture shall be in ce compliance. ip 65 protected led street light luminaries led street light fixture 150 watt 259 supply and erection of octagonal pole of following length and dimension as per table 3 with base plate on the cement concrete foundation of m 15 /m 20 grade (1:1.5:3) with the help of anchor bolts of grade 6.8 (is 1367 p iii ). the pole shall be made of s 355jo grade steel sheet , folded lengthwise to obtained octagonal shape, having single longitudinal seam weld and hot dipped galvanised internally & externally in accordance with is 2629. the pole shall have a weatherproof flush door and locking arrangements. the complete work shall be supervised and certified by the manufacturers for satisfactory supply, erection, testing and commissioning. 9 mtr. 260 supply, installation, testing and commissioning of copper wound transformers 33/0.433 kv, three phase, 50 hz, dyn 11, onan type , standard accessories with off load tap changer (+5% to 10% in steps of 2.5%), winding / top temperature rise of 45°c/40°c first fill oil, having permissible total loss values not exceeding 7.5% of the maximum total loss values for 11 kv as per energy efficiency level 2 at basic insulation level conferming to iss 2026 (part i to part ii), latest ammended and is 1180 part i : 2014. transformers described as above and as per the following continuous rating. 315kva 261 supply, installation, testing and commissiong of indoor type floor mounted metal clad, 11 kv incomer vcb panel up to 630 a equipped with following switchgears and accessories designed & tested as per latest standard i.e. iec 62271 200, suitable for stc 25ka/3 and iac a flr for 25ka/1sec. make of ht panel, vaccum interrupter and vcb should be of same make. 11 kv / 110 volts pt class 0.5 accuracy and 100 va burden with 1no. voltmeter (0 12 kv), analog type, selector switch for voltmeter and protection fuses/mcb for ht metering upto 12 kv on incomer, ammeter, analog type, selector switches for ammeters, microprocessor based numerical relay with o/l, e/f and s/c protection, set of dual core dual ratio 3cts of suitable ratio with sec 1 of 15 va burden and accuracy class – 0.5 for metering and class 5p10 for protection, multifunction meter. 262 sitc of dg set complete with 1500 rpm diesel engine of suitable bhp & ac brush less spdp alternator mounted on a common base frame & coupled through a flexible coupling or close coupled.alternator shall be self regulated with standard alternator protection( over voltage, over speed & under voltage). engine shall have residential silencer, up to 10 m exhaust piping , electronic / mechanical governor, manual & electric start, batteries, fuel tank ( with stand) & piping, control panel (16 g) with mccb (4p; 25 ka), ammeter, voltmeter, frequency meter, energy meter & hour meter, engine instruments panel, avm and with weatherproof, powder coated accoustic enclosure for dg set for sound attenuation fabricated from 1.6 mm crca sheet steel (structure) with side wall fabricated from 1.6 mm crca sheet and filled with foam as per cpcb norms latest amendments & is 8183 .the doors are fabricated from 1.6 mm crca sheet packed with accoustic material, floor of ms chequrred plate 5.0 mmthick, all doors/ opening are sealed with neoprene/ epdn gaskets. the enclosure has built in fuel tank, residential silencer (isolated from main dg chamber) with protection and tripping of dg set against temperature of more than 50 °c. all controls for operation of dg set are from outside the enclosure with dg control panel having microprocessor based genset monitoring and control system mccb ammeter, voltmeter, pf meter, frequency meter, kwh meter, ind. lamps etc. mounted inside enclosure , visible and accessible from outside. the enclosure should be suitable for following capacity dg sets and alternator. noise level is less than 75 db (a) at a distance of 1 mtrs. duly certified by authorized agency. complete in all respect of following capacity : radiator cooled and turbo charged 250 kva at 0.8 pf 415v 50hz 3 ?. 263 supply, installation, testing & commissioning of ht metering cubical panel as approved by discoms fabricated out of 14 swg crca sheet steel in two compartment & ms angle of size 60mmx6mm having provision for following: (i) provision for fixing trivector meter (to be supplied by discoms) (ii) provision for fixing of combined ct pt set (to be supplied by discoms) (iii)tt block (iv) 6mm bakelite sheet on all sides. 264 supply, installation, testing and commissioning of 11 kv double pole structure with air break switch having following specifications : (a) dp : double pole structure made of two nos. 9 meter long pcc poles (400 kg) & 7 nos. ms channel each of size 100 mmx50mmx2500mm complete with earthing of the structure as per rec standards in all respect with nuts, springs washers, clamps as required. (b) go:off load type gang operated 3 pole vertical flute type switch suitable for 11kv ; 400a ,3 phase, central post rotating double break isolator complete with ms hardware , copper moving & fixed contact ,assembly of 9 nos pin insulator ,gi pipe of suitable length for operation.c) do: 3 nos. horizontal/vertical mounted 33kv horn gap fuse set / drop out fuse set, 33kv barrel fuses mounted on 6 nos. post insulators. (c) do: 3nos vertical / horizontal mounted 11kv horn gap fuse set /drop out 11kv barrel fuses mounted on 6no pin insulators (d) la:3 piece non linear resistor type. lighting arrestor of approved make suitable for 3 wire, 11kv oh linewith rated voltage of 9kv rms & nominal discharge current rating of 5 ka & complete with galvanized clamping arrangement gi bolts, nuts, washer etc as required. (e) jumpers: 3 no 11kv acsr conductors mounted on pin type insularors as required. general:the go shall be operated by hand operated liver properly earthed with provision for locking mounted at 3’ 265 fire alarm g schedule 266 sitc of microprocessor based 2 wire loop (each loop accessing 90 addressable units ) fire alarm control panel. the panel shall be able to give pin point location of addressable units via the address code for each unit. the panel shall also be able to automatically switch off all control switches when ever any alarm is triggered. the panel shall also be able to give voice announcement to individualized speakers. the panel shall have built in sounder, maintenance free batteries of minimum 15 ah of 24 volts capable of minimum of 12 hours with battery charger, rectifier. loop cards, lcd unit to indicate fire / fault signal of individual unit, built in built / external printer, to log all incoming data etc complete in all respect. 2 loop. 267 sitc manual call point complete with , glass, hammer and chain etc as required: analogue addressable type 268 sitc automatic commendable control switches for shutting downac plant, power supply, gas supply etc. response indicators. 269 sitc fault isolators for isolating shorted, dead wire and loose circuits between two successive fault isolators with automatic resetting arrangement. analogue addressable type. 270 fire fighting g schedule 271 sub head i (wet riser system pumping equipments)sitc of electric driven sprinkler / hydrant pump suitable for automatic operation consisting of the following (a) horizontal multi stage centrifugal suction type pump complete for delivery of below mentioned discharge complete with necessary sluice value on the suction side ( all items to be matching the suction side of the pump) and pressure gauge sluice value and non return valve on the delivery side side ( all of the necessary dia) and including bypass arrangement for testing of pump.(b) squirrel cage induction motor suitable for 415 v, 50 hz, ac supply of below mentioned hp for the above pump ,1450 rpm t.e.f.c confirming to ip:55 and flexible coupling and coupling guard with the pump. (c) common bed plate fabricated from mild steel channel or cast iron type1620 lpm at 70 mtr head ( 50 hp motor) 272 sitc of diesel engine drive standby pump suitable for automatic operation consisting of the following a, b, c. .the diesel driven pump shall be suitable for following discharge:(a) horizontal multi stage centrifugal suction type pump complete for delivery of below mentioned discharge complete with necessary flexible pipe, sluice value on the suction side (all items shall be matching the suction side of the pump) and pressure gauge, sluice valve and non return valve on the delivery side (all of the necessary dia) and including bypass arrangement for testing of pump.(b) water cooled diesel engine developing suitable bhp for the below mentioned discharge at 1800 rpm, flexible coupling and coupling guard with the pump, common bed plate for mounting of the engine and pump, d cushy foot, damping arrangement by cushy foot, diesel engine starting panel for starting of the engine automatically with a unit of battery of 12/24v, 88 ah, 13/21 plate, exhaust pipe of minimum 10 m length, with muffler, day oil tank of 300 1ts capacity with first charge and hand operated oil pumpingset, supply, installation, testing, & commissioning of electric driven automatic pressurization pump setc) horizontally mounted single stage centrifugal end delivery pump of below mentioned discharge with necessary sluice valve on the suction side (all items matching the suction side of the pump) and sluice valve, non return value, pressure gauge on the delivery side including by pass arrangement for testing of the working of the pumping set as required.1620 lpm at 70 mtr head ( 50 hp engine) 273 sitc of jockey pump having squirrel cage induction motor suitable for 415 v, 50 hz ac supply with synchronous speed of 2900 rpm t.e.f.c type confirming to ip:55 and flexible coupling and coupling guard with the pump ,common bed plate of fabricated mild steel channel or cast iron type. 180 lpm at 70 mtr (15 hp). 274 supplying & installing cylindrical type air vessel, 250 mm dia 1.5m high of thickness 6.0 mm m.s. complete with air release valve, safety valve, pressure gauge etc.along with two coats of red oxide and two coat of post office red enamel paint as required. 275 providing & fixing 100mm dia pressure gauge on pump deliveryline complete with shut off cock. 276 sitc of pressure switches for main, jockey, and standby pumps,including necessary wiring upto control panel and stop valve. 277 sub head ii (hydrants system) 278 providing and fixing single headed hydrant valves with flanged inletisi marked with 63 mm female instantaneous outlet of gun metalcomplete with blank cap and chain conforming to is : 5290 279 providing . 63 mm dia 15 m long reinforced rubber hose pipeconforming to is : 636 1962, part –a & isi marked with gun metalmale & female coupling wire wound with the pipe. 280 providing & fixing (1.0 m x .45 m x 0.6 m ) outdoor hosecabinet suitable for accommodating hydrants made of not lessthan 16 swg. m. s. sheet having central opening glazed doorincluding necessary locking arrangement, painting (one coat primer& two coats of paint ) and housing 2 nos. rrl hose pipe, 1 nobranch pipe. 281 providing and fixing swinging drum type hose reel isi marked 30m(l) x 20 mm (dia) rubber lined pipe with shut off nozzle of 6 mm diaincluding the cost of 25 mm dia pipe connection from riser to hosereel , all sockets, nipples, elbows and 25 mm globe valve. 282 providing and fixing isi marked three way fire brigade inlet to wetriser with non return valve complete in all respects 283 providing, fixing, jointing and testing of heavy gauge (c class ) mspipe isi marked with accessories like tees, elbows, flanged joints,reducers, compressed asbestos gaskets, nuts and bolts includingfixing the pipe with suitable flat iron strip clamps /bracket, paintingetc. complete as required for delivery/ suction manifold relating tothe pump including painting of two coats of red oxide and two coatof post office red enamel paint including all civil breakages andmaking good the same : 284 200mm dia 285 150 mm dia 286 80 mm dia 287 sub head iii (piping, valves and accessories) 288 ms (medium duty b class) pipe with cleaning,wrapping and coatingof the pipe as per is; 10221 in all kind of soil at 1.0 m depthincluding excavation as required. 289 150 mm dia 290 100 mm dia 291 80 mm dia 292 providing & fixing butterfly valve with cast iron body, cast iron discand seat of nitrile rubber bonded on bakelite with hard back to pn1.6 rating with following sizes complete with bolts, washers andcompressed asbestos gasket as required 293 150 mm dia 294 100 mm dia 295 80 mm dia 296 providing and fixing non return valve complete with bolts nuts washers and compressed asbestos gasket etc as required : 297 200 mm dia 298 150 mm dia 299 80 mm dia 300 carbon dioxide type fire extinguisher with cylinder fully charge of 4.5kg capacity. 301 providing, fixing, testing & commissioning of sprinkler heads of thefollowing type : pendant type with quartziod bulb, operating temperature at 68 deg cas per specifications. 302 providing & fixing 10 swg chrome plated brass 100 mm diadecorative flanges / escutcheon plates to be fixed at junction ofsprinkler piping with the false ceiling. 303 sub head iii (piping, valves and accessories) 304 sub head iv (fire electrical control panel) 305 supplying and making end termination with heavy copper lugs (pin/ring type) duty crimped with crimping tool, pvc tape etc of followingsize 306 1.5 sq.mm 307 10.0 sq.mm 308 35.0 sq.mm 309 supply, fabricating & installing following sizes of perforated cable trays including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling with suspenders and including painting as required. 100mm x 50mm x 1.6mm 310 boundary wall g schedule 311 earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of engineer for following depths, below natural ground / road top level. in all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc. depth upto 1.5 m 312 excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 313 providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work upto plinth level : 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 314 providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement all work upto plinth level : 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size). (as per design mix) 315 reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto two stories excluding the cost of centring, shuttering, finishing and reinforcement: m 30 grade concrete. 316 centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete. 317 lintels, beams, plinth beams, girders, bressumers and cantilevers. 318 reinforcement for r.c.c. work at all levels including straightening, cutting, bending, placing in position and binding all complete. thermo mechanically treated bars 319 pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : raised and cut pointing. 320 random rubble stone masonry work in cement mortar with mechanical mixer in foundation (at any level) complete as per drawing and technical specification and as per clause 1000 and 1400 of mort&h specification including all scaffolding material, labour, machinery but excluding pointing and plastering. in cement mortar 1:4 (1 cement : 4 coarse sand) 321 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete: 322 earth work 323 dressing of earth work in surface excavation including cutting and filling upto 30cm depth including disposal of excavated earth upto 50m and lift upto 1.5 m. 324 earth work in excavation in open area, stp, wtp, pumping station with mechanical means including dressing of sides and ramming of bottoms, including getting out the excavated material, disposal of excavated material lead upto 1000m at suitable site as per as per drawing and as per direction of engineer. (measurements for payment to be done as per standard drawings). in all type of soil upto 3.0 m depth. 325 external development 326 compacting original ground 327 loosening upto a level of 500 mm below the subgrade level watered, graded and compacted in layers by vibratory roller 8 10 tonne to meet requirement of table 300 2 for subgrade construction as per mort&h specification clause 305.3.4. 328 loosening and recompacting original ground below embankment including loosening leveling and recompacting original ground supporting embankment to facilitate placement of of first layer of embankment, scarified to a depth of 150 mm, mixed with water at omc and then compacted by rolling by vibratory roller 8 10 tonne so as to achieve minimum dry density as given in table 300 2 for embankment construction as per mort&h specification clause 305.3.4. 329 providing, laying, spreading (with paver finisher only) and compacting wet mix macadam (wmm) base course comprising of graded stone aggregate and granular material conforming to mort&h specifications (table 400 ii) in layers of equal compacted thickness each consolidated, including pre mixing the material with water at omc in mechanical mixer (pug mill), carriage of mixed material by tippers to site, laying in uniform layers in base course on a well prepared sub base/ base course and compacting with power vibratory roller to achieve the desired density complete as per mort&h specification clause 406 including all material, labour, machinery, lighting, guarding and maintenance of diversion. 330 cement concrete pavements 331 providing and laying lean cement concrete 1:4:8 in sub base over a prepared sub grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600 1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid manualy, compacting with surface vibrator, finishing and curing complete as per clause 601, 112 of mort&h specification including all material, labour, machinery, lighting, guarding and maintenance of diversion. 332 providing and laying un reinforced, dowel jointed, plain cement concrete mix with concrete mixer & vibrator pavement over a prepared sub base with 43 grade cement , coarse and fine aggregate conforming to is: 383, maximum size of coarse aggregate not exceeding 25 mm, mixed as per approved mix design, laid, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, admixtures (if required) as approved, curing compound, finishing to lines and grades complete as per drawing and as per clause 602, 112 of mort&h specification including all material, labour, machinery, lighting, guarding and maintenance of diversion. pcc m 30. 333 providing and laying cast in situ cement concrete m 20 grade kerb stone channel top and bottom width 115 and 165 mm respectively, 250mm high laid with kerb laying machine, on 150 mm thick pcc m10 grade foundation (laid manually) as per design, including fixing at site as per clause 408 of mort&h specification including all material, labour, machinery, lighting, guarding and maintenance of diversion. using concrete mixer. 334 providing and fixing of 60mm thick precast cement concrete interlocking paver block casted with rubber moulds in approved reflective colour and design having minimun compressive strength of 300 kg/ sq cm. the cc paving blocks be laid on average 50mm thick bed of coarse sand and the joint is to be filled with fine sand. laying procedure on compacted sub base as defined. complete job is to be executed as per the instruction of engineer incharge. the rates to be inclusive of all lead & lifts etc. complete as per specifications. 335 flooring with cobble stone of approx. size 125x125x75 mm (thick) laid on 25 mm average thick cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the stone, laid in approved pattern complete in all respect as per direction of engineer in charge. 336 providing at site, lowering & laying in trenches, aligning & jointing of rcc pipes np4 class (with s/s ends) is: 458 2003 (amended up to date) marked and pipes from 300 mm and upto 1800 mm manufactured through vertical casting process at all depths with rubber gaskets (epdm/sbr) for sewer lines as per is: 5382 (including cost of rubber gaskets, lubricants) as per drawing, sectional hydro testing of the sewer pipe line (including cost and conveyance of water to site for testing) etc., complete as per specification and / or as directed by engineer. note : e/w to be measured and paid separately. 300 mm internal diameter. 337 horticulture work 338 grassing with doobs grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed. in rows 7.5 cm apart in either direction. 339 supply and planting following in poly bags / earthen pots well branched, well established & free from disease of 900 mm min. height plants at site in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required. 340 ficus panda 341 tecoma capensis ( ratanjot) 342 clerodendron inermii ( choti aari) 343 tabernaemontana variegated ( chandni) 344 hamelia patens ( firebush, thal kamal) 345 hibiscus variegated ( guddal) 346 supply and planting following in poly bags / earthen pots well branched, well established & free from disease of 300 mm min. height ground covers at site in 0.3 m dia holes, 0.3 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required. 347 wedelia trilobata ( sunflower family) 348 alternathera green (parrot leaf) 349 iresine herbstii (blood leaf) 350 ophiopogon black ( lily turf, mondograss) 351 asparagus myerii (fox tail) 352 lantana sellowiana 353 rhoeo spathacea compacta‘ ( oyster, boat lily) 354 golden duranta 355 pennisetum setaceum (fountain grass) ...

Urban Improvement Trust - Rajasthan

31789209 tender for swing seesaw jhule, open gym and other development work in nayakhera school ( ward no 29 ) civil work 1 part a boundary wall 2 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.all kinds of soils 3 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size ) . 4 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1 cement : 6 sand ) 5 providing and laying damp proof course with cement concrete grade m 150 ( 1 : 2 : 4 ) mortar prepared with 1% solution of water proof compound completeandno glass strips are used andnot applying 2 coats of hot bitumen complete as per specifications. 50mm thick. 6 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement.: m20 grade nominal mix 7 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. : m20 grade nominal mix 8 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding ( including cost of binding wire ) all complete up to floor three level.: hot rolled deformed bars ( is : 1139 ) . 9 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. 10 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. : centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for : columns, pillars, posts and struts etc. 11 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for : suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchorblocks, sills, chhajjas, lintel, beam, plinth beam etc. 12 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick. 13 providing and laying damp proof course with cement concrete grade m 150 ( 1 : 2 : 4 ) mortar prepared with 1% solution of water proof compound completeandno glass strips are used andnot applying 2 coats of hot bitumen complete as per specifications. 50mm thick. 14 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect. 15 new work 16 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 17 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.all kinds of soils 18 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size ) . 19 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m20 grade nominal mix1: 1.5: 3 ( 1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size ) . 20 flyash brick masonry with flyash bricks of class designation 75infoundation and plinth. cement mortar 1 : 6 ( 1 cement : 6 coarse sand ) 21 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick. 22 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 23 random rubble dry stone kharanja under floor. 24 polished blue kota stone flooring skirting, laid over 20 mm thick base of c.m. 1 : 4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete : for area of each slab from 901 to 2000 sq.cm :25 mm thick slab. 25 providing and fixing 15 to 20 mm thick granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12 mm ( av. ) thick base of cement mortar 1 : 3 ( 1 cement : 3 coarse sand ) jointing with white cement mortar 1 : 2 ( 1 white cement : 2 marble dust ) with pigment to match the shade of the granite slab complete including rubbing and polishing of : 26 jhunjhunu / jalore ( red / choclate colour ) upto 800 cm2 tiles 27 providing and laying damp proof course with cement concrete grade m 150 ( 1 : 2 : 4 ) mortar prepared with 1% solution of water proof compound completeandno glass strips are used andnot applying 2 coats of hot bitumen complete as per specifications. 50mm thick. 28 providing and fixing flush door shutters non decorative type ( hollow core construction ) with internal frame of 1st grade wood having styles and top rails of 100 mm width & bottom and lock rails of 150 mm width with 3 nos. cross battens of 50 mm thick width using 4 mm thick commercial ply on both faces of shutters & 6 mm thick beading of respective wood using with approved steel fitting as per annexure a : nigeria teak wood grade i 30 mm thick 29 providing and fixing factory made solid core single leaf window shutter made out of composite eco friendly wood laminated with 0.8 mm thick polymer termite and water resistant, fire retendent technology gluing by vaccume lamination technology various premoulded design on both face as per is 2202 ( part 1 & 2 ) 1991. window fitting shall be supplied by the department. 35 mm thick fully panelled 30 with wire gauge 24 gauge 14 mesh of is designation 85 gauge wires of dia 0.56 mm in panels 31 supplying & fixing of door & window chokhats / frames by metallic fastener with jointing arrangement confirming to is:4021 1995 ( ammended 2000 & 2009 ) made out of composite eco friendly wood confirmingto is:1658:2006 with suitable polymer primer termite &water resistive fire technology. 32 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats, or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 33 painting with synthetic enamel paint of approved brand and manufacture togive an even shade :two or more coats on new work 34 wiring of twin control light / fan / call bell point with 1.5 sq. mm nominal size fr pvc insulated unshethed flexible copper conductor 1.1 kv grade and 1.5 sq. mm nominal size fr pvc insulated unslated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) of approved make in surface / recessed isi marked mms ( is:9537 p iii ) pvc conduit & its accessories, round tles, 18 swg m.s. box with earth terminal, screwless cage connectors for neutral looping in switch board & false ceiling point, 6 a two way switch, 3.0 mm thick isi marked phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required. short point ( up to 3 mtr. ) 35 ( a ) short point ( up to 3mtr ) 36 ( b ) medium point ( up to 6mtr ) 37 ( c ) long point ( up to 10mtr ) 38 wiring of 3 pin 5 amp. light plug point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kg grade ( is:694 ) of approved make in surface / recessed isi marked medium duty pvc conduit & its accessories, hot dipped galvanized m.s modular box with earth terminal, screwless cage connectors for neutral looping in switch board , 6 a modular switch, 6 a modular socket, modular plate with grid plate, screws, making connections, testing etc. as required. on board 39 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor isi marked ( is:694 ) of 1.1 kv grade and approved make in existing surface or recessed conduit / casing capping including making connections etc. as required. 40 2 x 2.5 sq. mm + 1x1.5 sqmm 41 p&f 240 / 415 v ac mcb with positive isolation of breaking capacity not less than 10 ka ( b / c / d tripping characteristic ) isi marked is 8828 ( 1996 ) / conforming to iec 60898 in existing board / sheets including making connections with lugs, testing etc. as required. single pole mcb 42 6a to 32a rating 43 p & f star rated double ball bearing capacitor start, aluminium body & blade ceiling fan with down rod up to 30 cm with 3 x 1.5 sq. mm pvc insulated flexible copper conductor making connection testing etc. as required. 44 1200 mm sweep 45 p & f fluorscent tube fitting fabricated from prephosphated and powder coated crca steel and finish with powder coating / stove enamelled paint ) / ( extruded non corrosive uv resist ep channel ) complete with accessories ( low loss copper choke, starter, startes seat ) like electronic choke with terminal block duly prewired with copper conductor including making connection, testing etc. as required, ( without tube ) 46 1 x 36 watts eb 47 p & ffluorscent tube rod in existing fixture as required. 48 36 / 40 watt 49 part c open gym 50 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.all kinds of soils 51 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.m10 grade nominal mix 1: 3: 6 ( 1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size ) . 52 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1 cement : 6 sand ) 53 plaster on new surface on walls in cement sand mortar 1:4 including rackingofjointsetc. complete fine finish : 20mm thick . 54 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement: 3 coarse sand ) and making good the joints and cost of plastizers ( if required ) excluding the cost of centering, shuttering and reinforcement.: m20 grade nominal mix 55 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. 56 cement concrete pavement of required thickness with ( b ) 1:1.5:3 ( 1 cement:1.5 course sand : 3 graded stone aggregate 20 mm nominal size ) including finishing complete. 57 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m20 grade nominal mix1: 1.5: 3 ( 1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size ) . 58 providing and laying damp proof course with cement concrete grade m 150 ( 1 : 2 : 4 ) mortar prepared with 1% solution of water proof compound completeandno glass strips are used andnot applying 2 coats of hot bitumen complete as per specifications. 50mm thick. 59 random rubble dry stone kharanja under floor. 60 filling in plinth withlocally available good earth under floors including watering ramming consolidating and dressing complete including cost of locally available good earth 61 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect. 62 polished blue kota stone flooring skirting, laid over 20 mm thick base of c.m. 1 : 4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete : for area of each slab from 901 to 2000 sq.cm :25 mm thick slab. 63 painting with synthetic enamel paint of approved brand and manufacture togive an even shade :two or more coats on new work 64 supplying and fixing of chain link fencing with angle iron posts 50x50x6mm placed at every 3 mtr. apart 30cm in ground embedded in cement concrete 1:3:6 ( 30x30x45cm ) corner and every tenth post to be strutted with ( 50 x 50 x 6cm ) angle iron provided and fixed and fitted with posts including earth work in excavation etc. complete with chain link size.50mm x 50mm x 3.15mm 65 s / f of following outdoor gym ( fitness ) equipment for park as per enclosed drawing & design in special condition & direction of engineer in charge make india mart or sanhe city guiyuxing sportings goods co., ltd. or arihant or equivalent. 66 double bar:features : h 46, l 66, w 3 4 inch dia. galvanized steel pipe handle 1 / 1.25 inch dia. m.s. pipepowder coated 100 110 microns 67 sit up board:features : h 39, l 46, w 21 4 inch dia. galvanized steel pipe handle 1 / 1.25 inch dia. m.s. pipepowder coated 100 110 microns 68 double surf board:features : h 44, l 310, w 32 4 inch dia. galvanized steel pipe handle 1 / 1.25 inch dia. m.s. pipe powder coated 100 110 microns frp foot rest 69 sky walker:features : h 48, l 51, w 18 4 inch dia. galvanized steel pipe handle 1 / 1.25 inch dia. m.s. pipe powder coated 100 110 microns frp seat & foot rest 70 cross trainer:features : h 53, l 45, w 111 3 inch dia. galvanized steel pipe handle 1 / 1.25 inch dia. m.s. pipe powder coated 100 110 microns frp seat & foot rest 71 shoulder builder triple:features : h 63, l 48, w 36 3 inch dia. galvanized steel pipe handle 1 / 1.25 inch dia. m.s. pipe powder coated 100 110 microns 72 double twister seating :features : h 44, l 71, w 22 4 inch dia. galvanized steel pipe handle 1 / 1.25 inch dia. m.s. pipe powder coated 100 110 microns 73 ches press double:features : h 68, l 55, w 23 4 inch dia. galvanized steel pipe handle 1 / 1.25 inch dia. m.s. pipe powder coated 100 110 microns frp seat & foot rest 74 rower double:features : h 38, l 76, w 27 2x2 inch square crca pipe handle 1 / 1.25 inch dia. m.s. pipe powder coated 100 110 microns frp seat & foot rest 75 peck deck double:features : h 62, l 61, w 3, 2 3 inch dia, galvanized steel pipe handle 1 / 1.25 inch dia. m.s. pipe powder coated 100 110 microns frp seat & foot rest 76 leg press double:features : h 58, l 64, w 17 4 inch dia. galvanized steel pipe handle 1 / 1.25 inch dia. m.s. pipe powder coated 100 110 microns frp seat & foot rest 77 part d : external development 78 construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting by vibratory roller 8 10 tonne to meet requirement of table 300 2 including cost of compensation for earth taken from private land with lead upto 1 km as per morth specification : clause no. 305. 79 double swing : double swing is suitable for 4 to 14 years children and frame is made of nb pipes which should be following specifications :area : 3.0 mtr x 2.50mtr.safe play area : 4.0 mtr x 3.50 mtr.height : 2.40 mtr. ( on ground level ) leg support : 40mm nb pipes top bar : 50mm nb pipe seat : 9mm thick reinforced rubber ( non skid chequired top, bearing : housing special casting heavy duty bail bearing, suspension : 7mm dia electro galvanized chain ( iso : 9001 2000 make ) 80 single see saw : the single see saw suitable for 4 to 8 years children and made of ms pipes which should be following specification : area required : 1.50 mtr.x 3.0 mtr.height : 0.90 mtr. main pipe : 50 nb pipeplank : 40 nb pipehandle : 20 nb pipeseats : ms sheet ( 5mm thick ) frp ( iso : 9001 2000 make ) 81 parallel bars : parallel bars is suitable for 10 to 16 years children and main verticle frame made of 50mm nb pipe and horizontal bars made of 32mm nb pipes. horizontal bars having length 2.10 mtr. and height is 1.20 mtr. on ground level. total area of this parallel is 2.0 mtr. x 1.0 mtr. 82 up and down ladder : providing and fixing of up down ladder made out of ms pipe 40mm, 25mm size of length 10xheight should be less than 6 pipe should be isi marked of heavy weight. 83 wave slide : the sliding chute of wave slide is made of 6mm thick fibre glass reinforced plastic. ( binani or equivalent make ) with a smooth surface consist of 3 sliding mould of 2.00 ft. ( approx ) . the platform made out of 10 gauge ms sheet and shall be supported on 33mm od 14 gauge. the ladder shall be 60cm wide ( approx ) and will be made of 25mm np pipe with 15mm dual steps. the slide shall be supported on three parallel supports of different length. the size of the slide above the ground level shall be as follows platform height 2.40, slide length 4.20m and slide width 0.50 mtr. ( approx ) 84 providing and fixing benches with side panel casted in cast iron single piece and middle part is of mild steel. approx. ht. is 700 mm and length is 1250 mm the carving work is as per enclosed drawing and details and instruction of engineer incharge. 85 supply of different varieties of bougainvillea in ply bags / earthen pot according to height growth and age of plant at site including loading unloading and transportation etc. complete: local variety of bougainvillea 600mm to 900mm 87 lalri / anermi / golden duranta 88 crape myrtal / hemelia / lantana selloviana / lantana yellow / rukmani / gaudichaudi 94 supply and plantation of selected shrubs including mortality replacement, loading unloading transportation and maintenance for 30 days after planting 95 acalypha ceylon 3 4 96 cassia biflora 3 4 97 supply & stacking good earth at site complete including loading, unloading & transportation etc. 98 spreading of manure and good earth in required thickness (cost of manure and good earth to be paid separately) ...

Mohan Lal Sukhadia University - Rajasthan

31667958 miscellaneous work at mds hostel mlsu earthwork in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering and ramming and disposal of surplus excavated soil as directed within a lead of 50 mtr. all kind of soils. 2 providing and laying in position cement concrete including curing compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level 1:5:10 ( 1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size ) 3 filling available excavated earth ( excluding rock ) in trenches plinth side of foundation etc. in layers not exceeding 20 cm in depth consolidation each deposited layer by ramming and watering including lead up to 50 mtrand with all lift. 4 carriage of earth including loading, unloadiing etc lead up to 1 km 5 excavation for road way in soil by mechanical means including cutting and pushing the earth to site of embankment upto distance of 100 mtr. including trimming bottom and side slope in accordance with requirement of lines, grades and corss sections. 6 p & f plain fiber glass sheet ( frp sheet fiber reinforcement product sheet conforming to is: 12866 1989 having minimum thickness as below including fixing with nuts, bolts hooks and bitumen washer etc. complete:3.0 mm thick ( wt. 5.0 kg / mtr.sq ) 7 steel work in built up tubular trusses including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete above plinth level upto 4.5 mtr height.hot finished welded type tubes. 8 providing corrugated g.i. sheet roofing fixed with g.i. j or l hooks bolts and nuts 8mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead and including a coat of approved steel primer and two coat of approved paint on over lapping of sheet complete ( upto a pitch of 60 degree ) & excluding the cost of purlins rafters and truses, for class of sheets. 1.60mm thick 9 random rubble stone masonary for foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6 ( 1 cement : 6 sand ) 10 plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finish:25mm thick 11 plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finish:20mm thick 12 dismantling stone rubble masonry including stacking of serviceable material and disposal of unserviceable materialwithin 50 mtr lead.in cement mortar 13 dismantling stone rubble masonry including stacking of serviceable material and disposal of unserviceable material within 50 mtr lead.in cement mortar for thickness of tiles 25mm to 40mm 14 providing and fixing external grade board solid core ( tripple core ) single leaf boiling water and termite resistant flush door shutters isi 2202 67 marked using phenol formaldehyde resin in glue both sides with approved steel fittings complete as per annexurea. decorative teak veneer both sides ( factory fitted ) 35 mm thick 15 p / f ist quality vitrified porcelain polished tiles on floor skirting and steps etc. in different sizes ( thickness to be specified by manufacturer ) with water absorption less than 0.08% and confirming to is:15622 of approved make in all colour and shade, laid with 20mm thick c.m. 1:4 including grouting the joints white cement and matching pigment etc. complete size 600mmx600mm 16 providing and fixing ist quality mat finished ceremic tiles size 400x 400 mm confirming to is: 13755 & is: 15622 colour such as white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete ( including the cost of cement mortar bed 1:4 ) . 17 providing and fixing ist quality standard white / ivory, grey, fuma red brown, light green, light blue and other light shades glazed tiles of ( confirming to is : 13753 & is 13622 ) of size 300 mm x 450 mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in white cement mixed with pigment to match the shade of tile complete ( excluding the cost of cement plaster on walls & pillars ) . 18 add extra for using coloured dark shade tiles instead of white / ivory / light grey / light green / sky blue / light brown and other ligh shade colours 19 add extra for plaster over item nocement mortar 1:4 20 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade :two or more coats on new work including prepration of base with primer putty lippy complete in all respect. 21 brick masonaryin super structureup to third storeywith bricks of classdesignation 75 in cement mortar 1:6 ( 1 cement : 6 coarse sand ) 22 providing and layiny in position specified grade of cement concrete for rcc structure elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement ; 3 coarse sand ) and making good the joints excluding the cost of centering shuttering and reinforcement for beams, suspended floors, roofs, griders having slopes up to 15° , landings, balconies , shelves , chajjas, lintels, bands, plain window, sills , staircases and spiral staircases m20 grade design mix ( with weight batching plant only ) 23 providing and layiny in position specified grade of cement concrete for rcc structure elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 ( 1 cement ; 3 coarse sand ) and making good the joints excluding the cost of centering shuttering and reinforcement for walls ( any thickness ) including attached pilasters buttresses, plinth and string courses fillets columns pillars pearsabutments posts struts etc.m20 grade design mix ( with weight batching plant only ) 24 centering & shuttering with steel plates including strutting , propping, barcing both ways with wooden members and removal of form work up to floor three level for:suspended floors, roofs, landings staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blockessills, chhajjas, lintel, beams etc. 25 providing and fabricating reinforcement for rcc workincluding straightening, cutting, bending, placing in position in binding ( including cost of binding wire ) all complete up to floor three level thermo mechanically treated bars ( conforming to relevant is:1786. ) 26 providing and fixing granite stone slab thickness 16 18 mm mirror polished and machine cut in walls, pillars, steps, shelves, counter, floors etc. laid on 12 mm ( av. ) thick base of cement mortar 1:3 ( 1 cement : 3 coarse sand ) jointing with white cement mortar 1:2 ( 1 white cement : 2 marble dust ) with pigment to match the shade of the granite slab complete including rubbingand polishing of.jhunjhunu / jalore ( red / choclate colour ) above 3601 cm2 slabs 27 extra for providing edge moulding to 16 18 mm thick marble stone counters . vantities etc. over item no. 7.1 & 7.2 including machines polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. 28 providing & fixing anodized aluminium work ( anodizing to be got done from approved anodizer ) for doors, windows, ventilators and partition with extruded built up standard tubular and other sections of approved make confirming tois : 733 & is: 1285 anodized transperent 81 dyed to required shade according to is:1868 ( minimum anodic coating grade ac 15 ) , fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gap at junctions, at top, bottom and sides with required pvc / neoprene felt etc. aluminium section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, al. tower bolt & al handle & al drop etc. all complete as per architectural drawings and the directions of engineer in charge. ( glazing and paneling to be paid for separately ) .for fixed portions. 29 do for shutters of openable doors, windows and ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required ( lockers shall be paid for separately. ) . 30 do for shutters of openable sliding , windows and making provision for fixing of fittings wherever required ( lockers shall be paid for separately. ) . 31 p&f glazing in aluminium door, window, ventilator, shutters and partitions etc. with p.v.c. / neoprene or gasket etc.complete as per the architectural drawings & the directions of engineer incharge. ( cost of aluminium snap beading shall be paid in basic item ) . with glass panes of 5.0mm thickness ( weight not less than 13.75 kg / sqm ) . 32 providing and fixing 12mm thick prelaminated three layer medium density ( exterior grade ) particle board grade i, type ii conforming to is:12823 bonded formaldehyde synthetic resin of approved brand and manufacture in paneling fixed in alluminium doors, windows, shutters and partition frames with c.p., brass / stainless steel screws etc.complete as per architectural drawings and direction of engineer incharge. prelaminated particle board with decorative lamination on one side and balancing lamination on other side. 33 p&f expanded grill made of anodised aluminium as per design and drawing having members section of 7.5mm x 6.0mm and opening of size 50 mm x 50 mm to aluminium window / vent with required screws, y and h aluminium sec ( as per drawing ) at the ends and middle joints respectively complete in all respect as per direction of engineer incharge 34 s / f fixed wire gaugeofstainless steel of 14 mesh x 24 gauge to the aluminium beading 20x3 mm with suitable screw at not exceeding 150 mm distance at all hight with all lead and lift with scaffolding. 35 p&f brass lock without handle for aluminium door, of approved quality, make & design as directed by engineer in charge. 36 p & f double action hydraulic floor spring of approved brand and manufacture to aluminium door shutter including cost of cutting floors as required embedding in floors and cover plate etc. complete as per directon of engineer in charge confirming to is:6315 make...

Rajasthan Housing Board - Rajasthan

31356453 yearly rate contract rate for year 2022 2023 all sectors pratap nagar, sanganer, jaipur item 2 earth work in excavation by mechanical means (hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and all lift , disposed earth to be levelled and neatly dressed: all kinds of soil 810.00 cum 137.00 rs. one hundered thirty seven only 110970.00 2 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. all kinds of soils 500.00 cum 139.00 rs. one hundered thirty nine only 69500.00 earth, sand, lime, morrum manure or sludge for 20 km. 810.00 cum 83.60 rs. eightythree and paisa sixty only 67716.00 4 filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. 810.00 cum 66.00 rs. sixtysix only 53460.00 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 500.00 cum 2429.00 rs. two thousand four hundred twentynine only 1214500.00 6 m15 grade nominal mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size). 115.00 cum 3265.00 rs. three thousand two hundred sixtyfive only 375475.00 7 providing and laying in position specified grade of cement concrete for all rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. m20 grade nominal mix / design mix 100.00 cum 3811.00 rs. three thousand eignt hundred eleven only 381100.00 add extra for providing richer mixes respectively at all floor levels providing m 25 grade concrete by using min 410 kg of cement per cum instead of m 20 grade design mix. 40.00 cum 57.00 rs. fiftyseven only 2280.00 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. thermo mechanically treated bars (conforming of relevent is code) 9500.00 kg. 64.00 rs. sixtyfour only 608000.00 10 centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. 100.00 sqm. 116.00 rs. one hundred sixteen only 11600.00 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : walls (any thickness) including attached pilasters, buttresses plinth and string course. 200.00 sqm 214.00 rs. two hundred forteen only 42800.00 12 suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintel, beam, plinth beam etc. 400.00 sqm 248.00 rs. two hundred fortyeignt only 99200.00 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in : cement mortar 1 : 6 (1 cement : 6 coarse sand) 330.00 cum. 3236.00 rs. three thousand two hundred thirtysix only 1067880.00 add extra for square or rectangular pillars in superstructre brick work up to five storey upto 45 cm length and two corners are free 35.00 cum 133.00 rs. one hundred thirtythree only 4655.00 half brick masonry in foundation & plinth using bricks of designation 75 cement mortar 1 : 6 (1 cement : 6 coarse sand) 450.00 sqm. 350.00 rs. three hundred fifty only 157500.00 random rubble stone masonryr with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in: cement mortar 1:4 ( 1 cement : 4 sand). 275.00 cum. 2386.00 rs. two thousand three hundred eightysix only 656150.00 rajasthan housing board , jaipur name of work : yearly rate contract rate for year 2022 2023 place of work : all sectors pratap nagar, sanganer, jaipur g schedule 3 5 8 9 11 13 14 15 16 page 1 of 7 17 cement mortar 1:6 ( 1 cement : 6 sand). 450.00 cum. 2148.00 rs. two thousand one hundred fortyeignt only 966600.00 18 wall upto 30cm. and less thickness. 500.00 cum 144.00 rs. one hundred fortyfour only 72000.00 19 providing and laying coping with cement concrete grade m 15 (1 : 2 : 4) mortar complete with scaffolding,shuttering, glass strip at 1m interval finishing of surface with cm 1:3, rounding of edges fine finishing as per specification 50mm thick.. 500.00 sqm 300.00 rs. three hundred only 150000.00 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 200 x 300mm 75.00 sqm 535.00 rs. five hundred thirtyfive only 40125.00 21 300 x 450mm 75.00 sqm 803.00 rs. eignt hundred three only 60225.00 22 providing and fixing 1st quality mat finished ceremic tile size 300x300mm confirming to is : 13755 and is : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). 150.00 sqm 604.00 rs. six hundred four only 90600.00 23 extra for using size above 300x300mm in glazed tiles and for using 400mm x 400mm mat finished tiles in place of 300mm x 300mm size. 80.00 sqm 60.40 rs. sixty and paisa forty only 4832.00 p & f 1st quality soluble salt vitrified polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufacture) with water absorption less than 0.08% and conforming to is 15622 of approved make in all color and shade, laid with 20 mm thick cm 1 : 4 including grouting the joints with white cement and matching pigment etc complete. size 600 mm x 600 mm 80.00 sqm 945.00 rs. nine hundred fortyfive only 75600.00 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure a : 30 mm thick . commercial veneer both side 180.00 sqm 1338.00 rs. one thousand three hundred thirtyeignt only 240840.00 cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm thick nominal size aggregate. 250.00 sqm 211.00 rs. two hundred eleven only 52750.00 27 75mm thick with 20mm thick nominal size aggregate. 450.00 sqm 334.00 rs. three hundred thirtyfour only 150300.00 kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) for area of each slab from 2001 to 5000 sq.cm 50.00 sqm 825.00 rs. eignt hundred twentyfive only 41250.00 plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish : 20mm thick . 18000.00 sqm 123.00 rs. one hundred twentythree only 2214000.00 plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick. 10000.00 sqm 107.00 rs. one hundred seven only 1070000.00 31 extra for providing and fixing chicken mesh with plaster at joints of rcc and masonary complete fixing of mesh with nails including cost of mesh ,nails etc. 200.00 sqm 40.00 rs. forty only 8000.00 32 providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete 1000.00 sqm 86.00 rs. eightysix only 86000.00 33 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete 1000.00 sqm 62.00 rs. sixtytwo only 62000.00 finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding: new work (two or more coats applied @ 3.84 kg/10 sqm). 3000.00 sqm 41.00 rs. fortyone only 123000.00 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work 105.00 sqm 46.00 rs. fortysix only 4830.00 25 20 24 26 28 29 30 34 35 page 2 of 7 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: new work (two or more coats) over and including scrapping and priming coat with cement primer. 1300.00 sqm 59.00 rs. fiftynine only 76700.00 old work (one or more coats) including scrapping surface and necessary repairs. same colour 8300.00 sqm 29.00 rs. twentynine only 240700.00 painting exterior surface of wall with 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty, etc complete in all respect. new work 150.00 sqm 89.00 rs. eightynine only 13350.00 39 old work 2700.00 sqm 62.00 rs. sixtytwo only 167400.00 40 demolishing r.c.c. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. 50.00 cum 757.00 rs. seven hundred fiftyseven only 37850.00 demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge: in cement mortar. 250.00 cum 523.00 rs. five hundred twentythree only 130750.00 renewing glass panes, with putty and nails wherever necessary: float glass panes of thickness 5.0 mm 300.00 sqm 553.00 rs. five hundred fiftythree only 165900.00 providing and laying water proofing treatment over the existing r.c.c. roof as directed by engineer in charge and consisting of : (i) cleaning and washing of the existing roof including removing of loose material from the surface of cracks. (ii) widening and deepening of cracks to receive the terro crack filler or equivalent in two coats. (iii) application of one coat of terro seal or equivalent compound. (iv) application of one base coat of water puoofing compound and then application of net (made up of nylon and plastic of approved brand and desired thichness) and again application of two base coats of water proofing compound over the net. the three layers of approved water proofing material will be mixed with kerosene in proportion of 5 kg (water proofing material): 1 liter (kerosene) ratio and will be applied like gurmala plaster. (v) application of three or more coats of water repellent compound like terro seal or equivalent compound with soft brushes complete in all respect as per direction of engineer in charge. 3000.00 sqm 570.00 rs. five hundred seventy only 1710000.00 44 providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proffing cement compound @ 0.253 kg/sqm. b) laying second layer of fiber glass cloth when the first layer is still green . overlaps of joints of fiber cloth should not be less than 10 cm . c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. this will be allowed to air cure for 4 hours followed by water curing for 48 hours. the entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around d) fourth and final layer of brick tiling ‘with cement mortar or any other approved protective coarse. (which will be paid for separately) for the purpose of measurement the entire treated surface will be measured 500.00 sqm. 275.00 rs. two hundred seventyfive only 137500.00 45 120cm. high fencing with angle iron posts 50x50x6mm. placed at every 3 mtr. apart 30cm. in ground embedded in cement concrete 1:3:6 (30x30x45cm) corner & every tenth posts to be strutted with 50x50x6mm angle iron provided with three horizontal lines and two diagonals of black barbed wire between two posts fitted and fixed with g.i. staple including earth work in excavation etc. complete. 400.00 mtr. 419.00 rs. four hundred nineteen only 167600.00 dismantling of fencing dismantling of barbed wire fencing / wire mesh fencing including posts, foundation concrete, backfilling of pit by manual means including disposal of 200.00 rmtr. 32.00 rs. thirtytwo only 6400.00 47 patch repair to cement concrete floor including digging out old floor in regular shape and removal of rubbish curing etc. complete in all respects. 250.00 sqm 211.00 rs. two hundred eleven only 52750.00 48 washing floor with soda, soap or other cleaning material. 10000.00 sqm 1.00 rs. one only 10000.00 grinding of existing floor with 120 and 360 no. carborundum stone including cost of wax polishing complete : 900.00 sqm 33.00 rs. thirtythree only 29700.00 50 repair of existing steel glazed doors, windows and ventilator, ms sheet door, garge doors, compound wall gates etc. by welding drilling complete include. cost of welding rods and hire charge of welding meachine and tp etc complete 150.00 sqm. 239.00 rs. two hundred thirtynine only 35850.00 43 36 37 38 41 42 46 49 page 3 of 7 51 labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc. 450.00 sqm. 160.00 rs. one hundred sixty only 72000.00 52 cleaning and dusting of floor, roof etc. with approved cleaning material including disposal of unserviceable material / rubbish with all lead and lift after social function in community centres . 150.00 per function 889.00 rs. eignt hundred eightynine only 133350.00 53 annual maintenance of fire extinguisher dry chemical powder type 5 kg. capacity 20.00 each 550.00 rs. five hundred fifty only 11000.00 54 cleaning of building, bath, toilets, man hole, sewer line, drains, chambers etc. by sweeper including all cleaning articals.(community centres/office buiding) 10.00 month 6000.00 rs. six thousand only 60000.00 55 labour charges for checking & cleaning sewer pipe line upto 200 mm dia.including removal & transportation of sludge as directed by engineer incharge 1000.00 rmtr. 4.00 rs. four only 4000.00 labour charges for cleaning for internal man hole/chamber complete chamber 50.00 each 30.00 rs. thirty only 1500.00 57 manhole 50.00 each 50.00 rs. fifty only 2500.00 58 labour charges for checking & cleaning sewer pipe line upto 200 mm dia.including removal & transportation of sludge as directed by engineer incharge 10000.00 rmtr. 4.00 rs. four only 40000.00 providing and fixing unplasticized poly vinyl chloride (upvc) swr pipes type b for sciland waste discharge system (is:13592 : 1992 marked) of approved quality /make 75 mm dia 50.00 mtr. 116.00 rs. one hundred sixteen only 5800.00 60 110 mm dia 200.00 mtr. 219.00 rs. two hundred nineteen only 43800.00 61 160mm dia 25.00 mtr. 289.00 rs. two hundred eightynine only 7225.00 62 providing and fixing flex hoarding 10 oz flex sheet duly printing, letter writing, designing, iron sheet framing with wooden structure & angles for supporting of 35x35x5mm with erecting on temporay ballis post as per requirment of site duly approved by engineer incharge, including fitting at site. 2500.00 per sq. ft 90.00 rs. ninety only 225000.00 63 barricating with sal ballies as per design including tying with vertical post by coconut strings including digging out holes in all types of soil complete in all respect with two horizontal members height 1.2 m up to 1.5 m above ground level and vertical supports up to 2.5 centreand upto 3 days period including removal and cleaning the site complete in all respect & including dressing of sides in all types of soil. 500.00 mt 16.50 rs. sixteen and paisa fifty only 8250.00 64 providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 3000.00 kg. 77.00 rs. seventyseven only 231000.00 65 extra if square,rectangular hollow tubelar sections are used or grill made by flats only 3000.00 kg. 7.00 rs. seven only 21000.00 66 surface dressing of the ground including removing vegetation and inequalities not exceeding 15cm deep and disposal of rubbish lead up to 50 mtr. and lift up to 1.5 mtr.: all kinds of soil 10000.00 sqm 7.00 rs. seven only 70000.00 67 clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 25000.00 sqm 4.00 rs. four only 100000.00 clearing grass and removal of rubbish clearing grass and removal of rubbish up to a distance of 30 m outside the periphery of the area as per technical specification clause 201. 5.00 hectare 9054.00 rs. nine thousand fiftyfour only 45270.00 construction of embankment with material obtained from borrow pits construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of tables 300.1 and 300.2 with a lead upto 1000 mtr as per technical specification clause 301.5 500.00 cum 99.00 rs. ninetynine only 49500.00 excavation in cutting in soil by manual means with lead upto 50 m excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per technical specification clause 302.3 (for petty work qty upto 100 cum) 2160.00 cum 85.00 rs. eightyfive only 183600.00 removal of unsuitable soil with disposal upto 1000 m removal of unsuitable soil including excavation, loading and disposal upto 1000 m lead but excluding compaction ground supporting embankment subgrade replacement by suitable soil, which shall be paid separately as per clause 303.5.2 as per technical specification clause 302.3.11 1080.00 cum 27.00 rs. twentyseven only 29160.00 72 removal of blown sand including taking out and disposal of excavated material with lead up to 50mtr. and lift up to 1.5 mtr disposed soil to be levelled and neatly dressed. 540.00 p. cum 12.00 rs. twelve only 6480.00 compacting original ground compacting original ground supporting subgrade 56 59 68 69 70 71 73 page 4 of 7 loosening of the ground upto a level of 300 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of tables 300.1 and 300.2 for subgrade construction as per technical specification clause 303.5.2. 15000.00 cum 34.00 rs. thirtyfour only 510000.00 water bound macadam sub base/base wbm grading 1 providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80 100 kn static roller in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density grading 1 as per technical specification clause 404. (by manual means) 2160.00 cum 788.00 rs. seven hundred eightyeignt only 1702080.00 wbm grading 2 providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80 100 kn in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per technical specification clause 405. (using crasher broken aggregate) by manual means 1440.00 cum 1009.00 rs. one thousand nine only 1452960.00 wet mix macadam providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at by mechanical means with 1 km lead 360.00 cum 1011.00 rs. one thousand eleven only 363960.00 77 collection of binding material/mooram for w.b.m. course (p.i. 4 to 6), including stacking as per standard specifications 252.00 cum 450.00 rs. four hundred fifty only 113400.00 78 collection of quarry rubbish (p.i. less than 6), grading as per morth specification’s table 400 1, including stacking as per the standard 150.00 cum 350.00 rs. three hundred fifty only 52500.00 79 labour charges for patching w.b.m. using crushed / broken aggregates including preparation of pot hole scarifying & reshaping to the required grade 252.00 cum 185.00 rs. one hundred eightyfive only 46620.00 prime coat medium porosity providing and applying primer coat with bitumen emulsion (ss 1) on prepared surface of granular base including cleaning of road surface and spraying primer 360.00 sqm 51.00 rs. fifty one only 18360.00 tack coat providing and applying tack coat with bitumen emulsion (rs 1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and 720.00 sqm 14.00 rs. forteen only 10080.00 82 providing and laying dense graded bituminous macadam with 100 120 tph batch type hmp producing an average output of 75 tones per hour using 770.00 p. mt 2958.00 rs. two thousand nine hundred fiftyeignt only 2277660.00 providing and laying bituminous concrete with 100 120 tph batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per mort & h specifications clause 509 complete in all respects for grading ii (13 mm nominal size) bitumen s 65 2466.00 p. mt 3531.00 rs. three thousand five hundred thirtyone only 8707446.00 providing and laying reinforced cement concrete pipe np3 as per design in single row providing and laying reinforced cement concrete pipe np3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets clause 1106. 600 mm dia 48.00 rmt. 1288.00 rs. one thousand two hundred eightyeignt only 61824.00 85 300 mm dia 48.00 rmt. 540.00 rs. five hundred forty only 25920.00 cement concrete pavement construction of un reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 (grade), coarse and fine aggregates conforming to is:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14 days, using curing compound and water finishing to lines and grade as per drawing and technical specification clause 1501, including vaccum dewatering process with all required equipments 300.00 cum 3482.00 rs. three thousand four hundred eightytwo only 1044600.00 interlocking concrete block pavement 76 3 74 75 80 81 83 84 86 87 page 5 of 7 providing and laying of interlocking m 30 grade concrete block pavements having thickness 80mm as per drawings and technical specification clause 1504 with spreading 30mm thick sand under neath and filling joints with sand including providing and laying cc m30 edge blocks 300mm x 150mm x 300mm size. 3500.00 sqm 541.00 rs. five hundred fortyone only 1893500.00 88 cutting of construction joint/ longitudinal joint 4 to 6 mm. wide & 75 to 100 mm deep using mechanical concrete cutter including cost of diamond bit cutting wheel and filling of bitumen sealing compound in groove including cost of sealing compound. 300.00 mtr 55.00 rs. fiftyfive only 16500.00 providing and fixing of reinforced ferro cement drain cover designed for class aa loading duly marked on cover with adequate steel reinforcement having thickness 75 mm to 150 mm anti corrosive bitumen painted m.s. plate rim and on m.s. lifting hooks admixture like plasticizer bond improving compound shrinkage resistance compound abrasion resistant complete as per approved design etc. drain opening size standard drain cover size 451 mm to 700 mm (1000 x 800 mm) 100.00 sqm 1418.00 rs. one thousand four hundred eighteen only 141800.00 90 701 mm to 1200 mm (1500 x 600) mm 100.00 sqm 1785.00 rs. one thousand seven hundred eightyfive only 178500.00 91 providing and erecting typical citizens information board as per approved drawing & specification of morth made of two ms sheet of 1.6 mm thick each of size 900mm x 750mm stiffend by angle iron 25mmx25mm x 3mm all around the plate & plates fixed on frame of 75mm dia pipe of 12 swg sheet (vertical post 3050 mm with angle holdfasts and horizontal member 900mm) to be joined by embedded in cement concrete m 15 grade of block of 600mmx 600mm x 750 mm size below ground level as per enclosed drawings & as directed by engineering incharge. all ms will be stove anmeled on both side lettering. figuring and border will be with ready mixed synthethic enamel paint of superior quality in required shade and colour etc complete in all respect. all sections of framed post and steel tube will be painted with primer and two coat of epoxy paint as per drawing and as per mord specification. 25.00 each 6600.00 rs. six thousand six hundred only 165000.00 92 marking centre line and stop lines etc. on road as per irc pattern with thermoplastic paint of approved quality and make with 8% glass beads laid on the road surface at temperature 160 c with a special applicator machine complete with a special applicator machine complete with labour material and traffic diversion arrangements. 200.00 sqm 450.00 rs. four hundred fifty only 90000.00 supply & fixing of m 20 grade precast cement concrete kerb or dand upto 60 cm length over 20 mm thick base of cement mortar 1:6 including jointing earth work, painting & jointing with cement mortar 1:4 of size (22.5 x 25) / 2 x 30 cm 800.00 rmt. 436.00 rs. four hundred thirtysix only 348800.00 94 supply & fixing of direction and place identification sign board made out of 1.2 mm thick ms sheet framed to angle iron 35 x 35 x 5mm and two verticle post of angle iron 35 x 35 x 5mm 3 meter long with hold fast , stove enameled painting and lettering as per design and pattern of size 120 x 90 cm including of digging pits size 30 x 30 x 45 cm and fixing in c.c.1:5:10 including curing complete in all respect. 100.00 each 3800.00 rs. three thousand eignt hundred only 380000.00 painting on concrete/steel surfaces with epoxy painting two coats including prime coat with epoxy paint of approved brand on concrete/steel surfaces after through cleaning of surface to give an even shade as per drawing and technical specification clause 1701 800.00 sqm 96.00 rs. ninetysix only 76800.00 maintenace of bituminous surface road repair to pot holes and removal of loose material, trimming of sides, cleaning of surface by providing tack coat with bitumen emulsion, 20 mm thick pre mix carpet using catonic bitumen emulsion and seal coat type b with bitumen emulsion 300.00 sqm 210.00 rs. two hundred ten only 63000.00 97 providing and laying of kandhal readymade cold patching mix for repair of potholes in adverse climatic conditions including the bituminous mix with a minimum of 5.6% mc 100 cutback bitumen (containing a suitable antistripping agent) by weight of mix and in strict conformance in gradation and other requirements such as 6 month storage life as per the specifications laying in proper camber & grade compaction with road roller and transportation with all lead & lift complete in all respect as per direction of engineer in charge 2500.00 per kg 13.50 rs. thirteen and paisa fifty only 33750.00 supply of dry manure including loading unloading, transportation & stacking at site. fram yard manure (organic). 100.00 cum. 300.00 rs. three hundred only 30000.00 supply of chemical fertilizers at store in bags weighing not less than 50 kg. each including loading unloading & transporation etc. urea 20.00 per 50 kg.bag 220.00 rs. two hundred twenty only 4400.00 100 d.a.p. 20.00 per 50 kg.bag 550.00 rs. five hundred fifty only 11000.00 99 87 89 93 95 96 98 page 6 of 7 101 supply & stacking good earth at site complete including loading unloading & transporation etc. 100.00 cum. 100.00 rs. one hundred only 10000.00 supply of insecticides & pesticides at store in dust / liquid form complete. cholorophyriphos 20 ec. 20.00 per liter 325.00 rs. three hundred twentyfive only 6500.00 supply of p.v.c. hose pipe of different sizes at store including transportation etc complet : 25 mm dia. 50.00 r.mtr. 45.00 rs. fortyfive only 2250.00 supply of different varities of tree / shrubs / climbers according to height and age of the plant at site including loading/ unloading & transportation etc. complete : different varrities of climbers 900 mm to 1500 mm. 3000.00 each 37.50 rs. thirtyseven and paisa fifty only 112500.00 supply of different varities of tree(neem, gulmohar, kasia, alstonia, ashoka,etc.) according to height and age of the plant at site including loading/ unloading & transportation etc. complete : different tree 2401 mm to 3000 mm. 1000.00 each 300.00 rs. three hundred only 300000.00 supply of different sized pots at site store including loading unloading & transporatation etc. complete : cement pot 350 mm size 100.00 each 65.00 rs. sixtyfive only 6500.00 107 maintenance of shrubbary or hedge cutting including disposal of rubbish with all leads & lifts. 1000.00 sqm 3.00 rs. three only 3000.00 108 digging of pits size 60x60x60 cms. including removal of stones. manuring applicable of insecticides & watering atleast 15 litre per plant after planting. 1000.00 per pit. 15.00 rs. fifteen only 15000.00 109 prunning & trumming andcutting of old big trees on the road side the contractor will deposit the cut wood in the deptt. 10000.00 per tree 30.00 rs. thirty only 300000.00 maintenance of plants by the contractor including of pits/bids watering preparation of thavala hoeing weeding etc. & application of insecticieds etc. & security if the plant die during maintenance contractor has to replace same height plant at his own cost. trees 15000.00 per plant per month 10.00 rs. ten only 150000.00 111 shrubs or hedge 36000.00 per plant per month 5.40 rs. five and paisa forty only 194400.00 hire charges of plants & machinery 112 tractor with trolley . 72.00 per day 1050.00 rs. one thousand fifty only 75600.00 113 generator 250 kva. 12.00 per day 1200.00 rs. one thousand two hundred only 14400.00 114 hire and running charges of crane 20 tonne capacity. 12.00 per day 5500.00 rs. five thousand five hundred only 66000.00 115 hydraulic excavator (3d) with driver and fuel. 24.00 per day 6600.00 rs. six thousand six hundred only 158400.00 116 hire charges of diesel truck 9 tonne 72.00 per day 1350.00 rs. one thousand three hundred fifty only 97200.00 hire charges of labour 117 beldar 1200.00 per day 200.00 rs. two hundred only 240000.00 118 coolie 12000.00 per day 200.00 rs. two hundred only 2400000.00 119 blacksmith 1st class 50.00 per day 250.00 rs. two hundred fifty only 12500.00 120 fitter (grade 1) 50.00 per day 280.00 rs. two hundred eighty only 14000.00 121 mason (brick layer) 1st class 50.00 per day 300.00 rs. three hundred only 15000.00 122 kanat 9 x 6 fixed with tent. 30.00 1st day 19.80 rs. nineteen and paisa eighty only 594.00 123 water proof tripal ...

Public Works Department - Rajasthan

30784778 misc. civil works in iti banipark, jaipur. (sanction work) misc. civil works in iti banipark, jaipur. (sanction work) earth work in excavation by mechanical means (hydraulic excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.all kinds of soils 2 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.m10 grade nominal mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 3 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in: cement mortar 1:6 ( 1 cement : 6 sand). 4 providing and laying damp proof course with cement concrete grade m 150 (1 : 2 : 4) mortar prepared with 1% solution of water proof compound complete as per specification .75mm thick. 5 brick work with f.p.s. bricks of class designation 75 in superstructure above plinth level upto floor v level in all shapes and sizes in :cement mortar 1 : 4 (1 cement : 4 coarse sand) 6 half brick masonry in superstructure , above plinth level upto floor vlevelusing bricks of designation 75cement mortar 1 : 4 (1 cement : 4 coarse sand) 7 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor arches, arch ribs, domes, vaults, shells, folded plate, chimneys, shafts , roofs having slope more than 15º ,vertical and horizontal fins individually or forming box louvers, facias and eaves boardsm20 grade nominal mix / design mix 8 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level.(original producers who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to is:1786) thermo mechanically treated bars (conforming of relevent is code) 9 centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 10 plaster on new surface on wall in cement sand mortar 1:3 including racking of joints etc. complete fine finish : 12mm thick 11 plaster on new surface on walls in cement sand mortar 1:4 including rackingofjointsetc. complete fine finish : 20mm thick . 12 p & f 1st quality heavy duty vitrified double charged tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to is 15622 of approved make in all colour and shade, laid with 20 mm thick cm 1: 4 including grounting the joints with white cement and matching pigment etc complete. size600 mm x 600mm 13 providing and fixing in cm 1 : 4 double paitam (rebated) stone door window and ventilator frames of approved quarry :size 100 x 75mm. 14 providing and fixing m.s. sheet 1mm thicksingle leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of engg. incharge but excluding cost of chowkhats: including two coats of anit corrosive red oxide primer paint 15 supplying and fixing in walls machine cut and polished stone shelves, tands andin cm 1:3 with machine cut edges : kota stone minimum 30mm thick. 16 providing and fixing granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12mm (av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. south zed black above 3601 cm2 slabs 17 providing and fixingaluminum workfor doors ,windows, ventilators and partition with extruded built up standard tubular / appropriate z sections and other sections of approved make conforming to is :733 and is :1285,fixed with rawl plugs and screws or with fixing clips ,or with expansion hold fasteners including necessary filling up of gap. at junctions , at top ,bottom and sides with required pvc/neoprene felt etc. aluminium section shall be smooth ,rust free, straight ,mitered and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing /paneling , c.p. brass/ stainless steel screws al. tower bolt & al. handle & al. aldrop etc.,all complete as per architectural drawings and thedirections of engineer in – charge .(glazing and paneling to be paid for separately).powder coating aluminum( minimum thickness of powder coating 50 micron) 18 for shutters builtup standard tubular sections of openable doors ,windows & ventilators including providing & fixing hinges / rollers etc. and making provision for fixing of fittings wherever required (lockes shall be paid for separately).powder coating aluminum( minimum thickness of powder coating 50 micron) 19 extra for shutters of slidingaluminum windows 20 providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with pvs / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge.(cost of aluminium snap beading shall be paid in basicitem.) with float glass panes of 5.0 mm thickness ( weight not less than 13.50 kg/sqm) 21 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:newwork(twoormorecoats)overandincludingscrappingandprimingcoatwithcement primer. 22 finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). 23 earth work in surface excavation not exceeding 30cm. in depth but exceeding 1.5 meter in width as well as10 sqm on plan including disposal of excavated earth up to 50 mtr. and lift up to 1.5 mtr. disposed soil to be levelled and neatly dressed:all kinds of soil 24 providing and laying at or near ground level factory made kerb stone of m 25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand ) including making joints with without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete including painting etc. as per direction of engineer in charge (length of finished kerb edging shall be measured for payment). (precast c.c. kerb stone shall be approved by engineerin charge). 25 providing and laying ofpaver block as per is 15658 : 2006 (indian standard for precast concrete block for paving specification) and irc : sp:63 2004 (guidelines for the use of interlocking concrete block pavement) m 35,60mm thick to be used in light traffic (light traffic is defined as a daily traffic up to 150 commercial vehicles exceeding 30 kn laden weight, or an equivalent up to 0.5 million standard axles (msa) for a design life of 20 years(a standard axle is defined as a single axle load of 81.6 kn) like pedestrian plazas, shopping complexes ramps, car parks, office driveways , housing colonies, office complexes, rural roads with low volume traffic, farm houses , beach sites, tourist resorts, local authority footways, residential roads, etc.category‘b’ denated only two side like i,z,t shape etc. as per irc sp63:2004 26 rough chisel dressed kota stone 35 mm thick flooring of approved shade set in pattern over 20mm thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and pointingwith cement sand mortar 1:3 with pigment to match the shade of stone with joint thickness up to 15 mm complete in all respects : ...

Public Health Engineering Department - Rajasthan

30756089 nit14 conversion of scheme boodh block gangrar :conversion of p&t scheme to piped scheme boodh block gangrar district chittorgarh sl. no. item description 1 constuction of open well 4.0 m dia and 20.00 m deep at boodh 2 earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 mtr, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in lead of 50 mtr. all kinds of soil. 3 from0 m to 1.50 m bgl 4 earth work in excavation in foundation trenches or drains including dressing of sides and ramnming of bottoms lift up to 1.5 mtr including traking out the excavated soil and depositing and refilling of jhiri with watering and ramming and deposals of surplus excavted soil as directed with a lead in a 50 mtr including stacking of useful material if available. 5 ordinary rock 6 from 0.00 m to 4.50 m bgl 7 hard rock (requiring blasting) usefulmaterial 30 % 8 from 0.00 m to 6.00 m bgl 9 from 6.00 m to 25.00 m bgl 10 add extra over item no 2.39.2 4 for every additional; lift of 1.5 m or part thereof: in ordinary rock and hard rock. 11 in ordinary rock and hard rock 12 from 1.50 m to 3.00 m bgl 13 from 3.00m to 4.50 m bgl 14 from 4.50 m to 6.00 m bgl 15 from 6.00 m to 7.50 m bgl 16 from 7.50 m to 9.00 m bgl 17 from 9.00 m to 10.50 m bgl 18 from 10.50 m to 12.00 m bgl 19 from 12.00 m to 13.50 m bgl 20 from 13.50 m to 15.00 m bgl 21 from 15.00 m to 16.50 m bgl 22 from 16.50 m to 18.00 m bgl 23 from 18.00 m to 19.50 m bgl 24 from 19.50 m to 20.00 m bgl 25 add extra over item no 2.39 for excavation in saturated soil where pumping or bailing out of water is required including shorting strutting where required and dewatering. (respective applicable rates) 26 from 6.00 m to 7.50 m bgl 27 from 7.50 m to 9.00 m bgl 28 from 9.00 m to 10.50 m bgl 29 from 10.50 m to 12.00 m bgl 30 from 12.00 m to 13.50 m bgl 31 from 13.50 m to 15.00 m bgl 32 from 15.00 m to 16.50 m bgl 33 from 16.50 m to 18.00 m bgl 34 from 18.00 m to 19.50 m bgl 35 from 19.50 m to 20.00 m bgl 36 centering & shuttering with ply wood or steel sheets including strutting , propping, barcing both ways with wooden members and removal of form work up to floor three level for: walls (any thickness) including attached pilasters, buttresses, plinth and string course. add extra for shuttering in circular work in plan up to dia 10 m over item no 4.7.1 37 providing and fabricating reinforcement for rcc work including straightening, cutting, bending, placing in position in binding (including cost of binding wire) all complete up to floor three level 38 thermo mechanically treated bars (conforming to relevant is:1786.) 39 providing and laying in position specified grade of cement concrete for rcc structure elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement ; 3 coarse sand) and making good the joints excluding the cost of centering shuttering and reinforcement for : 40 walls (any thickness) including attached pilasters buttresses, plinth and string courses fillets columns pillars pears abutments posts struts etc. 41 m20 grade nominal mix (with graded stone aggregate 20mm nominal size) 42 structural steel work in single section fixed with connecting plate includingcutting hoisting fixing in position and applying a priming coat of approved steel primer all complete above plinth level upto 4.5 mtr. height 43 in flates, tees, angles & channals 44 in r.s. joists 45 estimate for construction of tube well 46 construction of tube well up to 100 mtr. depthin all type of rocks by dth system & over burden to accommodate casing pipe of following sizes in all types of soils & over burden including lowering of casing pipes, (if required) excluding cost of casing pipes, as per is:2800 part 1: 1991 andis:2800 part ii: 1979 (both amended upto date) and technical specifications. the work would be completed after obtaining sand free water. the tube well should have a throughout bore as per nominal dia of casing pipe. 47 nominal bore 200 mm dia. 48 add 15% extra on above item for drilling depth beyond 100 mtr, if depth of tube well is more than 100 mtr. 49 supply of erw m.s. black casing pipe isi marked (is: 4270/2001) or amended up to dateoffollowing sizes 50 200 mm dia nb (thickness of pipe 5.4mm & mass of tube 28.46 kg/m) 51 estimate for storage facilities 52 construction and commissioning of rcc intze type over head service reservoir of following capacity and staging as per the scope of work and technical specifications, consisting of the following main activities: 53 a) topographic survey, preparation of site contour plan, conducting sbc testand its approval from departmentbefore construction. submission and approval of concrete mix design and water quality test report for water to be used in construction. b) excavation in all types of soil, pcc below foundation, all rcc work, plinth protection all around the structure including all material, labour, shuttering, scaffolding etc.c) ohsr shall be provided with adequate plinth protection all around the structure in a width starting from edge of structure at gl and extending at least up to 1.0m beyond the edge of outer most projection of ohsr.the plinth protection shall consist of 150mm thick pcc in m 15 grade concrete laid over 150mm thick layer of compacted soil.d) providing and applying two coats of food grade epoxy paint on the inside surface on the top dome, edge beam and 600 mm height of the vertical wall.e)conducting successfully hydro test and water tightness test as per i.s. code.f) providing and applying three coats of anti carbonation paint on the top surface of the top dome.g) providing and applying three coats of cement based paint on the external surface of the container, balcony, cone wall, columns & beams etc..h) providing and fixing ss 304 ventilator, ss 304 manhole frame and cover and ss 304 ladder from top dome/slab to bottom dome/slab inside container. i) providing and fixing of ms section ladder from the last landing to balcony having railing all around it and ms ladder with safety cage from balcony to top dome/slab.j) providing and fixing water level indicator (float type). 54 rates for rcc ohsr,sbc 10 t/sqm, seismic zone ii & staging 18 m 55 200 kl capacity 56 construction of rcc (flat slab type) clear water reservoir of following capacity as per the scope of work and technical specification, consisting of the following main activities: 57 a) topographic survey, preparation of site contour plan, conducting sbc testand its approval from departmentbefore construction. submission and approval of concrete mix design and water quality test report for water to be used in construction. b) excavation in all types of soil, pcc below foundation & all rcc work including all labour and material charges including providing and fixing of accessories such as ss ladder, ss manhole frame and covers, water level indicator (float type), ss ventilator with ss screen, float valve, puddle collars, g.i. pipe railing around walk way, top dome/slab, staircase.c) cwr shall be provided with adequate plinth protection all around the structure in a width starting from edge of structure at gl and extending at least up to 1.0m beyond the vertical wall of cwr. the plinth protection shall consist of 150mm thick pcc in m 15 concrete over 150mm thick compacted soil fill.d) providing and applying two coats of food grade epoxy paint on the inside surface of the roof slab, and 600 mm height of the vertical wall.e) successful hydro test and water tightness test as per i.s. code.f) providing and applying three coats of anti carbonation paint on the roof slab.g) providing and applying three coats of cement based paint on the remaining external surface area of the structure. 58 h) providing and fixing ss 304 ventilator, ss 304 manhole frame and cover and ss 304 ladder from roof slab to bottom slab, inside container. providing and fixing water level indicator (float type).i) providing and fixing ms ladder from ground to top slab. j) all ms parts to be painted with two coats of the enamelled paint over the primer coat of red oxide.k) providing and fixing of 150mm wide water bar for the construction joints in the container.l) providing and fixing ci/di puddle collars the vertical wall for connecting inlet, outlet, overflow and washout pipes of the reservoir.m) inlet, outlet, overflow, washout pipes and valves are not included in this work, provision for the same shall be taken separately. 59 rates for rcc partially underground type clear water reservoir sbc 7 t/sqm, seismic zone 2,3 & 4 60 75 kl capacity 61 providing and fixing double flanged isi marked diclass k 9 pipes as per is:8329 2000 (amended up to date), asvertical pipes for rcc reservoirs including specials required such as duck foot bend, bend, tee etc. providing clamps at every 3 mtr,jointing materials such as nuts, bolt, rubber packing, hydraulic testingetc. complete in all respect up to and from valve chamber as per direction of eic, technical specification and scope of work. 62 100 mm 63 150 mm 64 200 mm 65 construction of rcc valve chamber 66 estimate for rising system 67 earth work in excavation by mechanical means (hydraulic excavator )/ manual meansin trenches of required width and gradient for laying and jointing of pipe lineincluding excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 mtr. including taking out the excavated soil, and then returning the soil asrequired in layers not exceeding 20cm in depth including consolidating eachdeposited layer by ramming, watering etc. and disposal of surplus excavated soil asdirected within a lead of 50 mtr. including required all safety provisions etc.:all kinds of soil 68 earth work in excavation by mechanical means (hydraulic excavator )/ manual meansin trenches of required width and gradient for laying and jointing of pipe lineincluding excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 mtr. including taking out the excavated soil, and then returning the soil asrequired in layers not exceeding 20cm in depth including consolidating eachdeposited layer by ramming, watering etc. and stacking serviceable material formeasurements and disposal of unserviceable material as directed, with in a lead of 50mtr. including all safety provisions required .: 69 ordinary rock 70 hard rock (requiring blasting) 71 hard rock(blasting prohibited) 72 dismantling of cement concrete pavement for pipe lineand chambers by mechanical means using pneumatic tools, cutting the peripheral edge by cc cutter, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. measurement for dismantled trench to be madeas per standard trench width specified in tender document and no extra payment shallbe made for trench width more than specified, re handling of material/earth to complete the tasks as per technical specification and scope of work. 73 providing and laying in position cement concrete in specified grade over prepared base course complete including finishing, curing, all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. measurement for cc work to be madeas per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified,complete work as per technical specification and scope of work. 74 m20 grade nominal mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). 75 providing, lowering, laying in trenches, aligning, fixing in position and jointingductileiron(di)isi markedk 7grades&spipesas per is:8329 2000 (amendeduptodate),withinternalcementmortar lining suitable for potablewater with rubber ring (epdm)joints as per is: 5382 1985 including all taxes (central and local), transportation and freight charges, inspection charges, loading/ unloading charges,including cost of labour and material, specials (tee, bend etc.) satisfactory hydraulic testing, disinfection etc. complete as per technical specifications and direction of engineer in charge. (excluding earth work) note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately. 76 100 mm 77 providing,lowering, aligning,fixingin positionin pipeline,cid/fsluicevalvesof approved make of following pressure rating & dia complete, confirming to is:14846 (amended up to date) and of following specifications: body, bonnet, wedge, gland, thrust plate, cap & hand wheel of grey cast iron of is:210/ fg200stem ss 304 ,body seat ring, wedge facing ring & bushes ltb2/ ss, face to face dimensions as per is 14846/2000 (amended up to date), all exposed machined ferrous surfaces shall be painted with one coat of aluminium red oxide primer conforming to is:5660 and two coats of black japan paint conforming totype b of is 341or paint conforming to is9862 or is2932( non toxic suitable for drinking water) applied inside and outside, flanges drilled as per is 1538.nut bolt confirming to is:1363 and is: 1367/ cs/ galvanised steel.insersion rubber of black epdm 6mm thick . suitablesupport structure as per directions of eic. sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge.note: rates are exclusive of tail piece/ dismantling joints and earth work. 78 manually operated ci sluice valve of class pn 1.0 79 100 mm hw 80 dismantling of cement concrete pavement for pipe lineand chambers by mechanical means using pneumatic tools, cutting the peripheral edge by cc cutter, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. measurement for dismantled trench to be madeas per standard trench width specified in tender document and no extra payment shallbe made for trench width more than specified, re handling of material/earth to complete the tasks as per technical specification and scope of work. 81 providing and laying in position cement concrete in specified grade over prepared base course complete including finishing, curing, all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. measurement for cc work to be madeas per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified,complete work as per technical specification and scope of work. 82 m20 grade nominal mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). 83 construction of rcc valve chamber 84 estimate for distribution system 85 providing, lowering, laying in trenches, aligning, fixing in position and jointingductileiron(di)isi markedk 7grades&spipesas per is:8329 2000 (amendeduptodate),withinternalcementmortar lining suitable for potablewater with rubber ring (epdm)joints as per is: 5382 1985 including all taxes (central and local), transportation and freight charges, inspection charges, loading/ unloading charges,including cost of labour and material, specials (tee, bend etc.) satisfactory hydraulic testing, disinfection etc. complete as per technical specifications and direction of engineer in charge. (excluding earth work) note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately. 86 80 mm 87 100 mm 88 providing, lowering, laying and jointing in trenches, standard lengths hdpeisi marked pipes as per is 4984: 1995 (amended upto date)with necessary jointing material like mechanical connectors, i.e. thread/ insert joint/ quick release coupler joint/ compression fitting joint or flanged joint and specials jointing pipe byelectro fusion welding method, including all taxes , transportation and freight charges, inspection charges, loading/ unloading charges, stacking of pipes, including cost of labour and material, specials (tee, bend etc.), satisfactory hydraulic testing, disinfection etc. complete as per technical specifications and direction of engineer in charge of following class and diameter. (excluding earth work) .note : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in rm measurement of the item and shall not be paid separately.supply may be in coil or straight length in 6 m/12 m. 89 hdpe pe 80pn 6 90 75 mm dia 91 90 mm dia 92 providing,lowering, aligning,fixingin positionin pipeline,cid/fsluicevalvesof approved make of following pressure rating & dia complete, confirming to is:14846 (amended up to date) and of following specifications: body, bonnet, wedge, gland, thrust plate, cap & hand wheel of grey cast iron of is:210/ fg200stem ss 304 ,body seat ring, wedge facing ring & bushes ltb2/ ss, face to face dimensions as per is 14846/2000 (amended up to date), all exposed machined ferrous surfaces shall be painted with one coat of aluminium red oxide primer conforming to is:5660 and two coats of black japan paint conforming totype b of is 341or paint conforming to is9862 or is2932( non toxic suitable for drinking water) applied inside and outside, flanges drilled as per is 1538.nut bolt confirming to is:1363 and is: 1367/ cs/ galvanised steel.insersion rubber of black epdm 6mm thick . suitablesupport structure as per directions of eic. sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge.note: rates are exclusive of tail piece/ dismantling joints and earth work. 93 manually operated ci sluice valve of class pn 1.0 94 80 mm hw 95 100 mm hw 96 earth work in excavation by mechanical means (hydraulic excavator )/ manual meansin trenches of required width and gradient for laying and jointing of pipe lineincluding excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 mtr. including taking out the excavated soil, and then returning the soil asrequired in layers not exceeding 20cm in depth including consolidating eachdeposited layer by ramming, watering etc. and disposal of surplus excavated soil asdirected within a lead of 50 mtr. including required all safety provisions etc.:all kinds of soil 97 earth work in excavation by mechanical means (hydraulic excavator )/ manual meansin trenches of required width and gradient for laying and jointing of pipe lineincluding excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 mtr. including taking out the excavated soil, and then returning the soil asrequired in layers not exceeding 20cm in depth including consolidating eachdeposited layer by ramming, watering etc. and stacking serviceable material formeasurements and disposal of unserviceable material as directed, with in a lead of 50mtr. including all safety provisions required .: 98 ordinary rock 99 hard rock (requiring blasting) 100 hard rock(blasting prohibited) 101 dismantling of cement concrete pavement for pipe lineand chambers by mechanical means using pneumatic tools, cutting the peripheral edge by cc cutter, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. measurement for dismantled trench to be madeas per standard trench width specified in tender document and no extra payment shallbe made for trench width more than specified, re handling of material/earth to complete the tasks as per technical specification and scope of work. 102 providing and laying in position cement concrete in specified grade over prepared base course complete including finishing, curing, all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. measurement for cc work to be madeas per standard trench width specified in tender document and no extra payment shall be made be made for trench width more than specified,complete work as per technical specification and scope of work. 103 m20 grade nominal mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). 104 estimate for pump house & pumping machinary 105 providing, installation, testing and commissioning of centrifugal monoblock pump set conforming to is 9079 operating at sync. speed 2900 rpm with requisite moc impeller, priming funnel, cock, suitable flanges at suction and delivery side. pump shall have common shaft for pump and motor. motor shall be suitable for working on 415 v ± 10%, 3 ph, 50 hz a.c. supply. motor shall be tefc type and pump set shall be suitable for working at various discharge and head requirements as per scope of work. pump shall be erected onc.c. foundation / cross channels / rsj frame block with suitable foundation bolts grouted in c.c. foundation block etc. complete in all respect as perspecification, scope of work and direction of engineer in charge of following power rating, suitable for prescribed duty conditions of one of the makes approved by technical committee. 106 centrifugal monoblock pump set (single stage) 107 5 hp 108 providing, installation, testing and commissioning of submersible monoblock pump set conforming to is 8034 and motor conforming to is 9283, with water proof winding. pump shall be suitable for various delivery head and discharge with stainless steel shaft. motor suitable for working on 415 v ± 10%, 3 ph, 50 hz ac and with water lubricated bearing to accept entire hydraulic thrust. supply, with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust. the pump set shall be suitable for direct coupling, with suitable suction strainer. pump should have suitable discharge out let as per manufacturers design. antithrust stream lined non return valve shall be provided with the pump and minimum 6 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided with each pump etc. completein all respect as perspecification, scope of work and direction of engineer in charge of following power rating, suitable for prescribed duty conditions of one of the makes approved by technical committee. 109 5.0 hp 110 providing, lowering, aligning, fixing in position in pipe line, ci double flanged swing type non return valves (nrv)of approved make of following pressure rating & dia complete, confirming to is: 5312 (part 1)/ 2004 (amendedup to date) and of following specifications: body, cover & disc of grey cast iron of is:210/ fg200. face to face dimensions as per is 5312 (part 1):2004 , flanges drilled as per is:1538. all exposed machined ferrous surfaces shall be painted with one coat of aluminium red oxide primer conforming to is:5660and two coats of black japan paints conforming totype b of is 341or paint conforming to is9862 or is2932( non toxic suitable for drinking water) applied inside and outside. body seat ring of ss/cs door face ring epdm/ neoprene (food grade quality) ,shaft of htb1/ ss aisi 410, hinge malleable cast iron / ss aisi 316/410 ,bonnet gasket epdm, bush leaded tin bronze/ ptet, gasketepdm/nbr,nut bolt as per is:1363 and is: 1367 (galvanised steel) ,insersion rubber of black epdm 6mm thick. suitablesupport structure as per directions of eic including jointing & jointing material, labour, testing and commissioning along with pipeline as per technical specification & as per direction of engineer in charge.note: rates are exclusive of tail piece/ dismantling joints and earth work. 111 class pn 1.0 112 100 mm dia 113 providing, lowering, aligning, fixing in position in pipe line at work site, di d/f resilient seated (soft seated) sluice valves (gate valves) , vacuum tight(bubble tight), straight and pocket less body passage of approved make of following class & dia complete confirming to bs en 1171/ awwa c 509 and of following specifications: body & bonnet of ductile cast iron of grade ggg40/ggg50 as per din 1693 or gr sg 400/12 as per is 1865 or equivalent grade as per is :3896 part2 1985 and subsequent revisions, wedge of same material as body & shall vulcanisedrubber lined with epdm (food grade quality) and seals of nbr face to face dimensions as per bs 5163 89/ is 14846/2000 (amended up to date) /din 3202 f4, stem/ spindle of ss (aisi 316 or equivalent) electrostatic epoxy powder(ep p)/ fusion bond epoxy ( non toxic suitable for drinking water) coated with minimum thickness of 250 microns inside and outside, drilled as per is 1538. nut bolt confirming to is:1363 and is: 1367(galvanised steel) insersion rubber of black epdm 6mm thick. suitablesupport structure as per directions of eic, sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per technical specifications and as per direction of engineer in charge. note: rates are exclusive of tail piece/ dismantling joints and earth work. 114 manually operated resilient seated sluice valves of class pn 1.0/1.6 115 100 mm dia 116 star delta starter 12.5 hp (1w+ 1s): i/c mcb 63a ,fp, 10 ka, c curve (1) , analog voltmeter 96*96mm ( 0 500v ) (1), volt selector switch (1) , analog ammeter 96*96mm ( 0 60a ) (1), amp. selector switch (1), c. t. 60/5a cl 1.0 5va (3) , indicating lights ( red 1, yellow 1) (2), indicating lights ( blue 1 ) (1), control mcb 6a sp 10 ka c curve (3)and o/g mcb 40a ,tp, 10 ka, c curve (2), power cont 18a tp ac3 duty(2), 2 no+2 nc aux. block(2), thermal overload relay (7 10a )(2), control mcb 6a sp 10 ka c curve (2), single phase priventer (2), indicating lights (red 1, green 1, amber 1)(6), push button 22.5 ( red 1, green 1 )(4), selector switch 1 pole, 2 way (2), capacitor 440vac heavy duty mpp type 5kvar (2), s/d timer(2) 117 supplying & installing 100 mm diameter sealed diaphragm bourdon type pressure gauge of range 0 to 10 kg.including all jointing material as per specification with safety cover. 118 estimate fortube well pumpset 119 supply & installation of 3 phase isi marked submersible motor pump set offive star rating by bee and as per is: 8034 2018 (pump) and is 9283 2013 (motor) or as amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well/dcb. the job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. 120 7.5 kw (10 hp) & head up to 120 mtr. 121 supply and fixing of electric control feeder panel comprising of suitable rating mccb , fully automatic star delta starter, over load relay,ampere meter with cts, volt meter, phase preventer, suitable starting capacitors, phase indicators, lighting arrangement etc. complete suitable for three phase pump set. the panel should have space for energy meter ( supplied by discom).all these equipments shall be housed by panel box made out from 18 gauge m.s. sheet with powder coating. panel should be ofminimum size 900 x 600 x 450 mm with stand ( made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg’s length 18 and double door including in built locking system.the legs should be embedded in m 15 cement concrete plat form. the size of cc platform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. the panel should have opening of suitable size in front of space for energy meter with glass for meter reading. the operation of panel should be suitable for on 440 volt ac supply. 122 above 5 hp and up to 10 hp 123 supply & fixing of isi marked three core pvc flat submersible cableas per is 694:1990 or amended up to date and conductor as per class 5 of is 8130:1980including making connection etc. 124 3 core 4.0 sq.mm 125 supply & fixing m s clamp set of 50x6 mm flat from iron with nuts and bolts etc for holding the riser pipe assembly of submersible pump set. 126 providing & lowering in tube well isi marked gi pipe “b class as per is:1239 or amended up to date threaded and double flanged (welded) on both ends and two number25x3mm ms flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. 127 50 mm dia 128 providing, installing, testing and commissioning of double flanged bulk flow meter with removable mechanism, of class b conforming to iso 4064/1 or amended upto date of approved make including cost of all material andlabouras per specifications with gi box (sheet 16 swg) suitable with locking arrangement of following dia. 129 50 mm dia 130 estimate for pump house & boundary wall 131 construction of pump house of required size suitable for installation of maximum 4 no. monoblock pump sets as per approved ga drawing, scope of work and technical specification complete work in all respect. 132 construction of boundary wall of brick/ stone masonary as per enclosed ga drawing, scope of work and technical specifications complete work in all respect. 133 providing and fixing steel, gate, grating and grills made of angles, tees, square bars, flats or black pipe with hold fast and fitting complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide and two coat of enamal paints. 134 construction of rain water harvesting structures at various govt building. 135 construction of tube well up to 100 mtr. depthin all type of rocks by dth system & over burden to accommodate casing pipe of following sizes in all types of soils & over burden including lowering of casing pipes, (if required) excluding cost of casing pipes, as per is:2800 part 1: 1991 andis:2800 part ii: 1979 (both amended upto date) and technical specifications. the work would be completed after obtaining sand free water. the tube well should have a through out bore as per nominal dia of casing pipe. (phed/2.4) 136 nominal bore 200 mm dia. 137 supply of erw m.s. black casing pipe isi marked (is: 4270/2001) or amended up to dateoffollowing sizes (phed/2.11.2) 138 200 mm dia nb (thickness of pipe 5.4mm & mass of tube 28.46 kg/m) 139 labour charges for making slots on blank pipes made of erw ms black pipe of following sizes, the slotting should be as per is:8110 2000 or as amended up to date. (phed/2.12.3) 140 200 mm dia nominal bore. 141 supply of bore well cover to accommodate 200 mm ms pipe made of ms flat & ms sheet as per drawings (pwd2019 4.8.4) 142 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 mtr. including required all safety provisions etc.:all kinds of soil 143 add extra for trenches for every additional lift over item no 5.0 144 above 1.5 mtr and up to 3.0 mtr. 145 earth work in excavation by mechanical means (hydraulic excavator )/ manual means in trenches of required width and gradient for laying and jointing of pipe line including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and stacking serviceable material for measurements and disposal of unserviceable material as directed, with in a lead of 50 mtr. including all safety provisions required. 146 ordinary rock 147 hard rock (blasting prohibited) 148 add extra for trenches for every additional lift over item no 6.0 149 above 1.5 mtr and up to 3.0 mtr. 150 providing and laying in position cement concrete including curing compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level using crusher broken aggregate 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm size) (pwd2019 3.2.7) 151 providing and laying in position specified grade of reinforcement cement concrete all rcc structural elements upto plinth levelincluding curing compaction finishing with rendering in cement sand mortar 1:3 ( 1 cement : 3 coarse sand) and making good the joints excluding the cost of centering shuttering and reinforcementm20 grade nominal mix (with graded stone aggregate 20mm nominal size) (pwd2019 4.1.2) 152 centering & shuttering with ply wood or steel sheets including strutting , propping, barcing both ways with wooden members and removal of form work up to floor three level for: suspended floors, roofs, landings staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks sills, chhajjas, lintel, beams etc. (pwd2019 4.7.2) 153 providing and fabricating reinforcement for rcc work including straightening, cutting, bending, placing in position in binding (including cost of binding wire ) all complete up to floor three level cold twisted deformed bars (is:1786) (pwd2019 4.12.2) 154 brick masonry in foundation & plinth, using bricks of class destination 75 in cement mortar 1:6 (1cement: 6 coarse sand)(pwd2019 5.1.7) 155 plaster on new surface on wall in cement sand mortar 1:3 including raking of joints etc. complete fine finish: 20mm thick (pwd2019 12.7.2) 156 steel work in single section fixed with connecting plate including cutting hoisting fixing in position and applying a priming coat of approved steel primer all complete above plinth level upto 4.5 mtr height. in flates, tees, angles & channals. (pwd2019 9.2.1) 157 supply & lying river gravels of following sizes in recharge shaft filter pit after screening & washing from kachha shift without deduction of voids. (pwd2019 4.28) 158 size 9 to 12 mm 159 size 3 to 5 mm 160 p&f rigid pvc pipe (is:4985 mark) class ii/ (4 kg. /cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. 110mm dia (pwd2019 3.19.3) 161 providing, laying & jointing of 110 mm dia hdpe pipe class pe 80 pn 6 162 p&f rigid pvc pipe fittings (is: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: (pwd2019 3.20) 163 bend 87.5, 110 mm dia 164 pipe clip 110 mm c18 165 door tee 110 mm 166 finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade inclg. all scaffolding new works ( three or more coats). (pwd2019 12.53.1) 167 making functional house tap connections ( fhtcs ). 168 providing household tap connectionas per technical specification andapproved drawing and as per relevant is code (amended up to date) from hdpe pipe line up to consumer meter/premises by using electro fusion saddle piece (complete job).this job includes digging out suitable size of pits and trench for laying service line in all kinds of soil; depositing and refilling of pit & jhiri with watering & ramming /compacting in layers and disposal of surplus excavated soil as directed with in a lead of 100 meter ; providing & fixing of all fitting duly approved in accordance withspecification for potable water including electrofusion saddle piece, gunmetal ferrule 4.0 mm , gm full way valve (is:778 mark) or wheel valve and specials, below ground level 20 mm nominal dia mdpe pipe pe80 pn 16 as per iso 4427 / 20 mm nominaldia ppr c (three layered) pipepn16 sdr 7.4 (is:15801:2008) (isi mark) for and above ground level using 20 mm dia ppr c pipe with standard ppr fittings/ 15 mm dia gi pipes with fittings in the premises for fixing a tap / meterbox (excluding) ,including accessories with flushing, cleaning, disinfecting and testing of pipe line complete required for making of service connection complete in all respect including labour charges . the service line should be laid at least 45 cm below ground level.note: road cut and restoration is not part of this item and paid seperately. 169 for connection with 20 mm dia mdpe/ppr c pipe length up to 05 mtr. 170 p& f bib cock (is : 8931 mark), superior quality of approved make , brss 400 gm, 15 mm nominal bore. 171 road cutting for house hold service connection in minimum trench width whereever road crossing is required. road cutting of cement concrete,wbm, black top etc. of all thickness shall be doneby using a concrete cutter machine keeping minimum trench width and restoration of the road with cement concrete with pcc m 10 and cc m 30 grade as per specification and direction of engineer in charge.. 172 add extra over item no 1.21 & 1.22 for providing20 mm pe80 pn 16 as per iso 4427 mdpe pipe including excavation, providing, laying & jointing of service line above 5.00 mtr. ...

Public Works Department - Rajasthan

30264754 02 various works in mppg college chittorgarh 02 various works in mppg college chittorgarh part a water hut 2 earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift up to 1.5 mtr, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in lead of 50 mtr. all kinds of soil. 3 providing and laying in position cement concrete including curing compaction etc . completein specified grade excluding the cost of centering and shuttering. all work up to plinth level using crusher broken aggregate1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) 4 random rubble stone masonry for foundation and plinth in cement sand mortar above 30 cm thick wall in:cement mortar 1:6( 1 cement : 6 sand ) 5 random rubble dry stone kharanja under floor 6 filling in plinth withlocally available river shingle under floors including watering ramming consolidating and dressing complete including cost of river shingles. 7 centering and shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formworks for foundation in basement rafts, footings, straps beams, bases of columns etc. up to plinth level. 8 providing and laying in position specified grade of reinforcement cement concrete all rcc structural elements upto plinth levelincluding curing compaction finishing with rendering in cement sand mortar 1:3 ( 1 cement : 3 coarse sand) and making good the joints excluding the cost of centering shuttering and reinforcement m20 grade nominal mix (with graded stone aggregate 20mm nominal size) 9 brick work in super structure up to third storeycement mortar 1:6 ( 1 cement : 6 coarse sand ) 10 half brick masonry in superstructure up to third storey including cost of nominal hoopreinforcement ( 2 nos. 6 mm dia m.s. bar at every forth course )cement mortar 1:4 ( 1 cement : 4 coarse sand ) 11 35mm thick rough chiesel dressed stone flooring of approved shade set in pattern over 20mm thick base of cement mortar 1:6 ( 1 cement : 6 coarse sand) and jointed with cement sand mortar 1:3 complete in all respects:nimbahera stone 12 providing and fixing granite stone slab thickness 16 18 mm mirror polished and machine cut in walls, pillars, steps, shelves, counter, floors etc. laid on 12 mm (av.) thick base of cement mortar 1:3(1 cement : 3 coarse sand) jointing with white cement mortar 1:2 ( 1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of.green/black/other graniteabove 3601 cm2 slabs 13 extra for providing edge moulding to 16 18 mm thick marble stonecounters . vantities etc. over item no. 7.1 & 7.2 including machines polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge.granite work 14 providing and laying in position specified grade of cement concrete for rcc structure elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement ; 3 coarse sand) and making good the joints excluding the cost of centering shuttering and reinforcement forbeams, suspended floors, roofs, griders having slopes up to 150 , landings,balconies , shelves ,chajjas, lintels, bands ,plain window, sills ,staircases and spiral staircases m 20 grade nominal mix (with graded stone aggregate 20mm nominal size) 15 centering & shuttering with ply wood or steel sheets including shuttering , propping, barcing both ways with wooden members and removal of form work up to floor three level for:suspended floors, roofs, landings staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blockes sills, chhajjas, lintel, beams etc. 16 plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finish:20mm thick 17 6 mm cement plaster to ceiling of mix 1:3 ( 1 cement : 3 fine sand) 18 polished blue kota stone flooring skirting laid over 20mm thick base of cm 1:4 and jointed with gray cement slurry to match the shade of the slab including rubbing and polishing completefor area of each slab from2001sq.cm to 5000 sq.cm20 mm thick slab 19 supplying and fixing in walls machine cut and polished stone shelves tands and sills in cm 1:3 with machine cut edgeskota stone 25 to 30 mm thick 20 grading roof water proofing treatment with :cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) with water proofing compound as per manufacturss specification 21 providing & laying broken glazed titles on 20mm thick in plain cement mortar 1:4 (broken glazed tiles not less than 9 kg/sqm) and joints filled with white cement with water proofing compund all complete as per direction of engineer in charge. 22 providing and fixing precast cement concrete coping 1:2:4 mix 50 mm thick complete as per specification: 23 providing batta (gola) 75mm x 75mm in cement concrete (1:2:4) including finishing with cement mortar 1:3 as per standard design. 24 providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section joints mitred and welded with steel lugs 13x3mm, 10cm, long embedded in cement concrete block 15x10x10cm of 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with coper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer excluding the cost of metal beading and other fitting except necessary hings of pivots steel handles peg stay etc. as required.partly fixed and partly openable (fixed area not to exceed 33 %). 25 providing and fixing square bars or other flat welded to window ventilatiors etc. 26 s&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by aluminium beading 20x3 mm with suitable screwsat not exceeding 150mm distance at all height with all lead and lift with scaffolding 27 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexurea30 mm thick commercial veneer both sideadd extro for sunmica 0.8 mm thick. 28 providing and fixing fully panelled double leaf shutter for doors as per approved design and drawing with approval ordinary c.p./oxidised steel fittings as per annexure a and width of styles & top rails of 100 mm and lock rails width of 150 mm and bottom rails of 200 mm width including teak wood beading of size 19 mm x12 mm on both faces complete. 30 mm thick wood sqm local wood gr i wire gauge 24 gauge 14 mesh of is designation 85 gauge wires of dia 0.58 mm panels 29 providing and fixing pressed steel mitred doors frames manufactured from commercial mild steel sheet of 1.25 mm ( 16 gauge) thickness including hings jamb, lock jamb, head and if required angles threshold of mild steel angles of section 50x25mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split and tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre treatment of the surface as directed by engineer in charge.double pitam door frameprofile e : 165 x 60 30 applying birla /jk white cement based putty over cement plaster surface for making even surface 31 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade :two or more coats on new work including prepration of base with primer putty lippy complete in allrespect. 32 finishing walls with acrylic smooth exterior paint of required shade including all scaffolding.new work (two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). 33 providing and fixing in position collapsible steel shutters with vertical m.s. , channels 20x10x2mm and bracket with flat iron diagonals 20x5mm, size with top and bottom rail of t iron 40x40x6mm . with top flat of 50 x 10 mm and bottom flat of 40 x 6 with 40mm dia steel pulleys/ ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer ( to be measured and paid as per outer dimension).with 75 mm opening when closed. 34 painting with enamel paint of approved brand and manufacture to give an even shade:two or more coats on new work 35 p&f seal coat with gril patti cement mortar 1:2, reinforced with 6mm wire fine finished with primer putty, paint complete in all respect as per design & direction by engineer in