40874623
tender for special repair of qtr 57 and 60 ( offers md accommodation ) of certain unit at mil station kota. ; 1 demolition / dismantling of existing roof treatment, any type from rcc roof slab including lime concrete / pcc padding over roof, removing layer of bitumen under lime concrete / pcc padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside md land, complete all as specified and directed. 2 demolition / dismantling of existing roof treatment, any type from rcc sunken slab including lime concrete / pcc filling materials around wc upto top of existing sunken slab, removing layer of bitumen under lime concrete / pcc sunken, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside md land, complete all as specified and directed. 3 taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. 4 taking down chowkhat or frames not exc 1.50 sqm each with shutters ( with out taking off shutters from the frame ) , complete all as specified and directed. 5 taking down chowkhat or frames exc 1.50 sqm and not exc 4.00 sqm each with shutters ( with out taking off shutters from the frame ) , complete all as specified and directed. 6 takingdown shutters of any description exc 1 sqm and not exc 2 sqm each and removing from site complete all as specified and directed. 7 takingdown shutters of any description exc 2 sqm each and removing from site complete all as specified and directed. 8 takingdown and re fixing after rescuring or easing and adjusting of any description exc 1 sqm & n. exc 2 sqm each in the same opening complete all as specified and directed. 9 takingdown and re fixing after rescuring or easing and adjusting of any description exc 2 sqm each in the same opening complete all as specified and directed. 10 demolition of cement concrete ( un reinforced ) of any description and in any position not otherwise specifically provided for and removing rubbish from premises ( distance exc 1.5 km but not exc 5 km ) , complete all as specified and directed. 11 demolition of cement concrete ( un reinforced ) in ground floor and pavings n.exc 15 cm thickness ( below or above gl ) and removing rubbish from premises ( distance exc 1.5 km but not exc 5 km ) , complete all as specified and directed. 12 demolition of cement concrete ( reinforced ) as in roofs, floors ( other than ground floors ) , beams, staircases, landing, chajjas and similar suspended work for and removing rubbish from premises ( distance exc 1.5 km but not exc 5 km ) , complete all as specified and directed. 13 dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. 14 demolition of stone slabs and tiles of any description or thickness in floors etc, laid, bedded and pointed in any mortar, complete all as specified and directed. 15 dismantling floor, hearth or wall tiling / terrazzo including cement mortar bedding ( but not backing ) , removing tiles and rubbish off the premises, complete all as specified and directed. 16 demolition of brick work or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles, complete all as specified and directed. 17 providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sqm of the vertical surface of the sub structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed. 18 treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 ( 1 cement: 2 coarse sand ) to match the existing floors complete all as specified and directed. 19 m&l brick work with old size pulverized fuel ash lime bricks ( fly ash bricks non modular size ) , straight or curved on plan exc 6 m mean radius, built in cm 1:6, complete all as specified and directed. 20 m&l for brick work with pulverised fuel ash lime bricks ( fly ash bricks non modular size ) , straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed. 21 m&l for pcc 1:3:6 type c 2 ( using 40mm graded stone aggreate ) , 75 mm thick as in plinth protection / path / pcc paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where dirtected and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling ( one part of hot bitumen 85 / 25 and three parts of fine sand by weight ) , complete all as specified & directed. 22 m&l for 100mm thick plain cement concrete 1:3:6 type c 2 ( using 40 mm graded crushed stone aggregate ) as in flooring / sub base finished surface even & fair to receive floor finishes / screed complete all as specified and directed. 23 m&l for 50mm thick plain cement concrete 1:2:4 type b 2 ( using 40 mm graded crushed stone aggregate ) as in flooring finished surface even & smooth without using extra cement complete all as specified and directed. 24 m&l providing cement concrete 1:2:4 type b 1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating & formwork, complete all as specified and directed. 25 m&l providing cement concrete 1:2:4 type b 1 using 20 mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed. 26 s & f 40mm gi pipe, medium grade, 60cm long out of which 20cm projected outside for spout pipe, placed in slope to drain water accumulated in sunken portion including making good in cm 1:3 for the damaged portion complete all as specified and directed. 27 m&l for pcc 1:2:4 mix type b 0 ( using 12.5 mm graded crushed stone agg ) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed. 28 m&l brushing neat cement slurry with 3.00 kg cement per sqm, complete all as specified and directed. 29 m&l for applying 15 mm thick screed in cm 1:4 on roof slabs with using liquid water proofing compound as per manufacturers instructions, complete all as specified and directed. ( liquid wpc shall be measured and paid separately ) . 30 m&l for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and supply and fix app polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 kg / sqm, black finish reinforced with non woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to is 3384 @ of 0.40 kg / sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. note: ( i ) coved fillets in pcc ( 1:2:4 ) type b 0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall / mumty / chimney / other vertical surfaces and thereafter surface painted with hot paving bitumen of grade 30 / 40 confirming to is 73, applied@1.20 kg / sqm over a coat of cold applied bituminous primer conforming to is:3384 @ 0.40 kg / sqm. 31 item 30.00 contd........ ( ii ) polymeric membrane shall be taken to a height of 45cm ( minimum ) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. ( iii ) the waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. ( iv ) in case of stone masonry parapet wall etc a groove of size 25mmx25mm ( minimum ) shall be made in coved fillet at the junction of roof and parapet wall / mumty chimney / other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. ( v ) cost of above aspects is deemed to be included in quoted rates. 32 m&l for cleaning of walls and floor of sunken portions including picking, sweeping clean and washing down with water to remove dust, dirt etc and supply and fix app polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 kg / sqm, black finish reinforced with non woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to is: 3384 @ 0.40 kg / sqm, torching overlaps with a propane or a butane gas torch with an overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold applied bituminous primer all as per manufacturer’s instructions, complete all as directed.note: ( i ) the waterproofing treatment shall be got carried out through the manufacturer or their authorized applicators only. 33 supply only approved liquid water proofing compound, complete all as specified and directed. 34 s&f 35mm thick factory made iind class hard wood ( hollock ) paneled door shutters two panel with lock rail and panel of 9mm b.w.p. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to is 710 or 12mm thick particle board veneered with commercial veneering on both faces. the size of rails & style as specified in ssr part i ( 2009 ) section 8 and as per is 1003 ( part i ) kiln seasoned as per is 1141 and chemically pressure treated as per is 401 complete all as specified and directed. 35 s&f 35mm thick factory made iind class hard wood ( hollock ) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass / gauge etc. the size of rails & style as specified in ssr part i ( 2009 ) section 8 and as per is 1003 ( part i ) kiln seasoned as per is 1141 and chemically pressure treated as per is 401 complete all as specified and directed.note : s & f glass / gauge shall be measured and paid for separately. 36 m&l in renewal of 18 / 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. 37 s&f in renewal of factory made pressed steel cupboard shutters alongwith frame, frame made of 1.25 mm thick pbi sheet and shutter made of 1.00 mm thick pbi sheet with 6 nos 3.15 mm thick and 100 mm long steel hinges per shutter, godrej pattern locking arrangement with 12 mm dia vertical rod and lock with duplicate key & chrome finish handle, duly spray painted in factory with two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete with fastener, hold fast etc as required at site, complete all as specified and directed. ( total width including frame shall be measured for payment purpose ) . 38 s&f in renewal of 18 mm thick hdwpc ( high density wooden plastic composite ) kitchen cupboard / door shutter board, one side colour / white laminate and other side decorative as in modular kitchen / cabinet door shutters fixed with minifix hardware where ever required & including edge band 22 mm wide 0.80m thick of matching colour on exposed surfaces of board fixed with polymaster adhesive including trimming edges of edge band to true line of thickness of board by manual trimmer, fixed to wall etc, complete all as specified and directed. 39 s&f in renewal of 18 mm thick hdwpc ( high density wooden plastic composite ) board of both side white laminate as in back kitchen and other side un decorative as in back of kitchen cabinet / partition of cupboard etc, complete all as specified and directed. 40 s & f in renewal continuous ( piano ) hinges, stainless steel, matt or brush finish, width of flaps ( when open ) in 40mm complete all as specified and directed. 41 s&fof ball catches with 8 mm dia steel ball and brass body and striking plate including letting in and fixed, complete all as specified and dirceted. 42 s&f ss handles, fancy type, 100 mm size, complete all as specified and directed. 43 s & f auto closing hinges, three dimentional adjustment with suitable mounting plate made of stainless steel with nickel plated for corrosion resistance for cupboard and cabinet shutters of kitchen, complete all as specified and directed. 44 s & f in renewal of kitchen basket cutlery stainless steel of size 435mmx510mm & including ss guide channel etc, complete all as specified and directed. 45 s & f in renewal of kitchen basket plate rack stainless steel of size 435mmx510mm & including ss guide channel etc, complete all as specified and directed. 46 s & f in renewal of kitchen basket utensils stainless steel of size 435mmx510mm & including ss guide channel etc, complete all as specified and directed. 47 s&f of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140 mm, complete all as specified and directed. 48 s&f aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed, complete all as specified and directed. 49 s&f aluminium handles, cast type, anodised 100 mm size, complete all as specified and directed. 50 s&f aluminium handles, cast type, anodised 150 mm size, complete all as specified and directed. 51 s&f 100 mm sizemild steel butt hinges, isi marked, medium weight, cold rolled and fixed with screws, complete all as specified and directed. 52 s & f 250 mm long aluminium alloy, anodised sliding door bolts ( isi marked ) with bolt not less than 16mm dia with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy and fixed complete all as specified and directed. 53 s&f 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, welded to mild steel frame complete all as specified and directed. 54 s&f snake guard ( door seal aluminium plate with rubber beading ) for door etccomplete all as specified and directed. 55 supply only stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, fixed to door, window, ventilator etc complete all as specified and directed. ( note: cost of fixing of wire cloth shall be deemed included in the unit rates under respective items. ) 56 s & f for solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with m.s. square tube, suppling & fixing in opening as per specification & drawing as applicable to item 08095 given in ssr part – ii ( 2020 ) . 57 s & f for factory made solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of m.s. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour pvc ‘c’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in ssr part–ii. 58 providing and fixing factory made upvc white colour sliding window ( area not exceeding 2.00 sqm each ) , three track made of extruded profiles with wall thickness of 2.3mm ( + 0.2mm ) . window profile with hollow section with multi chamber. frame ( 88mm x 52mm ) , sliding sash ( 42mm x 67mm ) . sliding mesh sash ( 42mm x 57mm ) sliding interlock ( one vertical length in each shutters ) ( 45.5mm x 28mm ) , glazing bead ( 24.5mm x 16mm ) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. epdm gasket, 1.2+ 0.2mm thick galvanised steel frame ( 30mm x 18mm ) 2 nos, sliding sash ( 30mm x18mm ) , sliding mesh sash ( 26mm x 10mm ) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, hardware.touch lock of zinc alloyed ( white powder coated ) , steel roller system. stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories etc., complete all as specified and directed.note : ( i ) the unit rate quoted by contractor includes cost of glass and ss steel wire cloth and includes all other connected accessories. net opening will be measured for payment purpose. ( ii ) provision for fixing the ac and cooler shall be included in rate quoated by the bidder, no payment shall be made on this account and no misunderstanding entertained in later stage. ( iii ) bidder shall note that all the accessories ( packing, hinges, handles etc ) of upvc window shall be maintained by manufactureres till defect libility period and quoated rate shall be included this provision. 59 supply and fixing factory made upvc white colour fixed glazed window / ventilator made of ( small series ) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension ( area upto 0.75 sqm. ) comprising of upvc multi chambered frame and mullion ( where ever required ) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length ( shape & size according to upvc profile ) , upvc extruded glazing beads of appropriate dimension, epdm gasket, g.i. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. profile of frame shall be mitred cut and fusion welded at all corners, mullion ( if required ) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. after fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality including provision of exhaust fan etc., complete all specified and directed. note : ( i ) for upvc frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. ( ii ) the unit rate quoted by contractor includes cost of glass and ss steel wire cloth and includes all other connected accessories. net opening will be measured for payment purpose. ( iii ) provision for fixing the exhaust fan shall be included in rate quoated by the bidder, no payment shall be made on this account and no misunderstanding entertained in later stage. ( iv ) bidder shall note that all the accessories ( packing, hinges, handles etc ) of upvc window / ventilator shall be maintained by manufactureres till defect libility period and quoated rate shall be included this provision. 60 s&f factory made steel windows conforming to is 1038 with side hung shutters & including box type hinges, with 2 nos steel handles, 2 nos tower bolts & steel pag stay complete ( without glazing bars ) , dovetailed or welded including fixing of lugs in pcc 1:2:4, type b 1, using 20mm graded stone aggregate & making good walls & cills to match the existing and including one coat of red oxide / zinc chrome primer complete all as specified and directed.note : ( i ) ss or ms cloth wire shall be measured and paid for sepparately under respective items. ( ii ) window size and pattern wherever required and directed shall be suitable for installing desert cooler. 61 s&f factory made steel ventilator with top hung shutter including hinges, steel peg stay and including one coat of red oxide / zinc chrome primer complete all as specified and directed. 62 s&f factory made steel ventilator with fixed type shutter without glazing bars including hinges, steel peg stay and including one coat of red oxide / zinc chrome primer complete all as specified and directed. 63 welding in repairs thickness of metal to be welded not exc 6mm and length of welding exc 2.5 cm but not exc 5cm complete all as specified and directed. 64 s&f sheet glass 3 mm thick ordinary quality and glazing with oil putty etc in squares n.exe 0.50 sqm in each pane, complete all as specified and directed. 65 s & f of framed work as in doors or gates of angles or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with including either hooks and hinges or steel hanging door fittings ( excluding of steel sheeting or other covering running rails and guides ) and hanging also fastening and fixing, conforming to fe 290 grade e 165, complete all as specified and directed. 66 s&f mild steel framed work as in grills, grating etc. with end of bars shouldered and / or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: cages, frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to fe 290 grade e 165, complete all as specified and directed. 67 m & l for cutting holes in brick / stone masonary walls in cement mortar exc. half brick but not exc. one brick for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type b 1 as required, complete all as specified and directed. 68 dismantling plain or corrugated steel sheeting, any gauge, any thickness incl hooks and ridge as retrieved from site complete all as specified and directed. 69 s&f pre painted galvalume aluminium zinc coating gi based corrugated steel sheet, 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering, wall cladding etc, fixed to iron / wooden members with self drilling zincoulium coated metal screws having cap with rubber and metal washers, complete all as specified and directed. 70 re fixing only pre painted galvalume aluminium zinc coating ( gi based corrugated steel sheet, 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering, wall cladding etc, fixed to iron / wooden members with self drilling zincoulium coated metal screws having cap with rubber and metal washers, complete all as specified and directed.note : pre painted galvalume aluminium zinc coating sheets obtained from dismantling shall be reused under this item. 71 s&f in renewal of stainless steel tubular curtain rods, 25 mm dia, with fixing brackets and one pair of decorative end caps etc, complete all as specified and directed. 72 m&l 100 mm thick pcc 1:4:8 type d 2, using 40 mm graded crushed stone aggregate, as in sub base of floors, etc., finished surface even & fair to receive floor finishes / screed complete all as specified and directed. 73 m&l machine pressed precast concrete interlocking paver block any shape and size made with grey cement and pigment, confirming to is 15658 2006 of 60 mm thickness, m 35 grade, laid over and including 25 mm thick sand cushioning, complete all as specified and directed. 74 m&l for 25mm thick plain cement concrete 1:2:4 type b 1 ( using 20 mm graded crushed stone aggregate ) as in flooring / sub base finished surface even & fair to receive floor finishes / screed complete all as specified and directed. 75 m&l for joint free non skid ceramic coloured tiles, 7 to 8mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in cm 1:6, complete all as specified and directed. 76 m&l for light coloured vitrified tiles, 10mm thick ( square / rectangular ) area of each tile not exceeding 0.36 sqm ( 600x600mm ) , in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in cm 1:6, complete all as specified and directed. 77 m&l for light coloured vitrified tiles, 10mm thick ( square / rectangular ) area of each tile not exceeding 0.36 sqm ( 600x600mm ) , fixed on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 10 mm thick rendering in cm 1:4 backing, complete all as specified and directed. 78 m&l glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in cm 1:4 backing, complete all as specified and directed. 79 m&l for machine cut kota stone slab as in flooring 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing andmirror polishing by applying wax polish, laid over and including 15 mm thick screed bed in cm 1:4, complete all as specifiedand directed. 80 m&l for machine cut kota stone slab as in skirting, dado, risers etc, 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and mirror polishing by applying wax polish, laid over and including 15 mm thick rendering in cm 1:4, complete all as specifiedand directed. 81 m&l for grinding of the existing marble / kota stone flooring by mechanical process using corborundum stone of appropriate grit, cleaning & finally mirror polishing by applying wax polish complete all as specified and directed. 82 m&l black granite ( of any type ) slab 18 20 mm thick, table rubbed and mirror polished by applying wax polish as in cooking platform, jambs, cills, pillars, tread, risers, platform for whb etc including bull nosing to exposed outer edges, set in cm 1:4 bedding and pointing with white cement mixed with pigment and provn of hole for gas pipe, laid over and including 20 mm thick screed bed in cm 1:6, complete all as specified and directed.note : granite stone slab shall be laid in single piece with rounding of edges and a grove shall be provided beneath the projection portions of slab. 83 m&l for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed. 84 m&l for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed. 85 m&l for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4 ( using water proofing compound as per manufacturers instructions ) , surface finished even and smooth without using extra cement, complete all as specified and directed. ( liquid wpc shall be measured and paid separately ) . 86 m&l for rendering 5 mm thick on fair faces of ceiling in cement mortar 1:3 including finishing the surface even and smooth, complete all as specified and directed. 87 m&l for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over & including one coat of red oxide zinc chrome primer, complete all as specified and directed. 88 m&l for preparing old steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed. 89 m&l applying 2 coats of synthetic enamel paint over and including a coat of pink primer on wooden surfaces, exceeding 10 cm in width or girth, incl preparation of the new surfaces complete all as specified and directed. 90 m&l applying two coats of synthetic enamel paint on wooden surfaces, exceeding 10 cm in width or girth, incl preparation of the old surfaces complete all as specified and directed. 91 m&l preparation of newly plastered surfaces of walls and applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying two coats distempering with 1st quality acrylic distemper ( ready mixed ) having voc content less than 50 gms / litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification over new surfaces on walls complete all as specified and directed. 92 m&l for complete removal of existing treatment from previously treated plastered / unplastered surfaces of walls and applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying two coats distempering with 1st quality acrylic distemper ( ready mixed ) having voc content less than 50 gms / litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification over new surfaces on walls complete all as specified and directed. 93 m&l preparation of newly plastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10sqm over new surfaces over new surfaces on walls complete all as specified and directed. 94 m&l for complete removal of existing treatment from previously treated plastered / unplastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10sqm over new surfaces over new surfaces on walls complete all as specified and directed. 95 m&l for applying three coats of white wash on ceiling including preparation of new or previously untreated surfaces, complete all as specified and directed. 96 m&l for applying two coats of white wash after preparation of old previously treated plastered surfaces of walls, complete all as specified and directed. 97 m&l for applying one coat of white wash after preparation of old previously treated plastered surfaces of ceiling, complete all as specified and directed. 98 s&f in renewal of hdpe pvc connection 450 mm long suitable for 15 mm gi pipe with two ptmt nuts and rubber washers complete all as specified and directed. 99 s&f in renewal of vitreous china wash hand basin white with flat back of size 550x400 mm, excluding chain and plug, taps and porcelain stopper but incl pvc waste pipe of 32 mm bore, suitable size of waste fittings, one pair of 600 mm long cast iron brackets, complete all as specified and directed. 100 s&f in renewal of shower rose, chromium plated brass, 100 mm size with swivel joint, screwed to iron pipe or for union of 15 mm dia, complete all as specified and directed. 101 cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed. 102 taking up or down existing gi tubing and connections, including making good the disturbed surface for 15 mm bore pipes complete all as specified and directed. 103 taking up or down existing gi tubing and connections, including making good the disturbed surface for 20 mm bore pipes complete all as specified and directed. 104 supply, fixing, laying & testing 15 mm bore galvanised iron water tubing medium grade with and including all gi fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed. 105 supply, fixing, laying & testing 20 mm bore galvanised iron water tubing medium grade with and including all gi fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed. 106 dismantling existing water storage tank of any description of capacity exc. 250 ltr but n.exc. 500 ltr, complete all as specified and directed. 107 dismantling existing water storage tank of any description of capacity exc. 500 ltr but n.exc. 1000 ltr, complete all as specified and directed. 108 s&f in position rotational moulded polyethylene water storage tanks 500 lts capacity, white colour ( cylinderical verticalwith closed top ) hoisted and fixed in position, complete all as specified in ssr part i and as directed.note: pvc tank shall be isi marked and having three layers. 109 s&f in position rotational moulded polyethylene water storage tanks 1000 lts capacity, white colour ( cylinderical verticalwith closed top ) hoisted and fixed in position, complete all as specified in ssr part i and as directed.note: pvc tank shall be isi marked and having three layers. 110 s&f of 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed. 111 s&f in renewal of 20 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed. 112 s&f in renewal of 15 mm bore stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union complete all as specified and directed. 113 s&f in renewal of stop valve 15 mm nominal bore, cast copper alloy, fancy type, chromium plated with long shank and cup ( concealed type ) , screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to gi socket complete all as specified and directed. 114 s&f in renewal of bib taps, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handles, screwed down, screwed for 15 mm bore gi pipe or for brass ferrule orto gi socket complete all as specified and directed. 115 s&f in renewal of angle valve 15 mm bore cast copper alloy, cp, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed, complete all as specified and directed. 116 s&f in renewal of two way angle valve 15 mm bore, cast copper alloy, chromium plated with long shank and cup ( concealed type ) , screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to gi socket complete all as specified and directed. 117 s&f in renewal of kitchen sink mixer cp hot & cold, 15mm bore, bright finish with three joints screwed the ends for iron pipe and plugging etc completeall as specified and directed. 118 s&f in renewal of wall mixer fitting with built in non return valve with 3 in 1 wall mixer, chromium plated brass, fancy type for 15mm bore completeall as specified and directed. 119 s&f in renewal of basin mixture cp hot & cold, 15mm bore, bright finish with three joints screwed the ends for iron pipe and plugging etc completeall as specified and directed. 120 s&f in renewal of vitreous china floor mounted water closet pan ( pedestal pattern ) with & including superior quality dual type low level pvc flushing cistern, water jet spray and health faucet & including connection to drain or out going pipe and to flushing pipe, antisyphonage pipe etc., & including plastic seat cover white with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and directed. 121 s&f in renewal of vitreous china squatting pan orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed. 122 s&f in renewal of 10 ltr capacity pvc low level flushing cistern, top push type with inlet ball valve, pvc float, brackets & including superior quality pvc flush pipe of 32 mm dia, completeall as specified and directed. 123 s&f in renewal of sink with draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality pvc waste pipe and connecting union to pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm fixed on granite stone slab and top of granite stone match with top of kitchen sink complete all as specified and directed. note : granite stone slab shall be measured and paid in separately with appropriate item of boq. 124 s&f in renewal of sink with draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality pvc waste pipe and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed. 125 s&f in renewal of stainless steel utensil plate rack of size 900 x 600 x 200 mm, made of 0.60 mm thick stainless steel sheet and fixed in position, design and pattern as approved by the ge, complete all as specified and directed. 126 s&f in renewal of 600x450 mm bevelled edge mirror 5.5 6mm thick selected quality glass flaw less, mounted in 6 mm thick ac buildings board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 127 s&f in renewal of ptmt alloy toilet cabinet with mirror of overall size 350x450 mm and fixed to wall complete all as specified and directed. 128 s&f in renewal of soap dish fancy type, chromium plated, approx size 160x160x90mm, fixed to plugs with chromium plated brass screws etc, complete all as specified and directed. 129 s&f in renewal of toilet paper holder, chromium plated, fixed to plugs with chromium plated brass screws etc, complete all as specified and directed. 130 s&f in renewal of 300 mm corner glass shelf with abs brackets etc, complete all as specified and directed. 131 s&f in renewal of grating doom of 100 mm dia, made of mild steel chromium plated, complete all as specified and directed. 132 s&f in renewal of pvc ( swr ) 75 mm dia floor trap, with cp grating including jointing to waste pipe and fixed in cement concrete 1:2:4 type b1 ( using 20 mm graded stone aggregate ) complete all as specified and directed. 133 s&f in renewal of salt glazed stoneware gully traps of size 150x150, square or round mouthed, type p complete all as specified and directed. 134 s&f in renewal of 100mm cast iron sanitary connection socket to fit wc out let complete all as specified and directed. 135 s&f pvc ( swr ) pipe 75 mm bore, single socketed, in any length with rubber ring joints laid in trenches or in floor and including dismantling of old u / s existing pipes alongwith fittings and accessories complete all as specified and directed. 136 s&f pvc ( swr ) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to walls and including dismantling of old u / s existing pipes alongwith fittings and accessories complete all as specified and directed. 137 s&f pvc ( swr ) pipe 75 mm bore, single socketed, in any length with rubber ring joints and fixed to walls and including dismantling of old u / s existing pipes alongwith fittings and accessories complete all as specified and directed. 138 s&f pvc ( swr ) bend 75 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed. 139 s&f pvc ( swr ) bend 110 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed. 140 s&f pvc ( swr ) 110 mm bore junction single, ( single t ) equal or unequal with oval access door, incl jointing to waste pipe with solvent cement, complete all as specified and directed. 141 s&f pvc ( swr ) 75 mm bore junction single, ( single t ) equal or unequal with oval access door, incl jointing to waste pipe with solvent cement, complete all as specified and directed. 142 s&f pvc ( swr ) vent cowl 110 mm dia, incl jointing to waste pipe with solvent cement, complete all as specified and directed. 143 s&f stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, dia of pipe 100 / 110 mm, complete all as specified and directed. 144 s&f stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, dia of pipe 75 / 80 mm, complete all as specified and directed. 145 demolition and breaking up drain pipes 150mm dia ( salt glazed ware, ac or reinforced concrete ) set in cement mortar complete all as specified and directed. 146 m&l for cement concrete 1:4:8 type d 2 using 40mm graded stone aggregate as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, for 150mm bore of pipe complete all as specified and directed. 147 m&l 150 mm bore reinforced concrete pipes, class np2, laid to slope in trenches and jointed in cm 1:1 and tested, complete all as specified and directed. 148 excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying cables etc not exc 10 sqm on plan and getting out in soft / loose soil, complete all as specified and directed. 149 returning filling in excavated soil including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as specified and directed. 150 removing excavated materials ( soil ) not exc 50 m distance and depositing where directed at a level not exc 1.5 m above the starting point, complete all as specified and directed. 151 taking down carefully copper / aluminium point wiring ( light, fan, socket or power ) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed. 152 dismantling unserviceable main switch / dbs incl wooden board and deposit to mes store yard including making good disturbed surface of wall complete all as specified and directed. 153 taking down sub main wiring of any size / capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed. 154 m&l for point wiring with pvc insulated ( frls ) unsheathed multi stranded copper conductor cable of size 1.5 sqmm with pvc insulated ( frls ) unsheathed multi stranded copper conductor cable of size 1.5 sqmm as earth continuity wire to be drawn in and including pvc concealed conduit not less than 20 mm dia including with all accessories and fittings, fixed in concealed & including providing ms sheet metal sunken switch / terminal box 1.2mm thick for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surfaces, complete allas specified and directed for the following: one light / ceiling fan / exhaust fan / bell buzzer point controlled by one, one way switch of 5 / 6 amps.note : cutting chases and making good to match with the adjoining surface deemed to be included in the unit quoted rate. 155 all as per item no 153.00 ( here in before ) but one 5 pin, 5 / 6 amps socket outlet point on independent board, controlled by one, one way 5 / 6 amp switch. 156 all as per item no 153.00 ( here in before ) but one 5 pin, 5 / 6 amps socket outlet point on same board, controlled by one, one way 5 / 6 amp switch. 157 all as per item no 153.00 ( here in before ) but one light point controlled by two, two way switch of 5 / 6 amps. 158 m&l point wiring with pvc insulated ( frls ) unsheathed multi stranded copper conductor cable of size 2.5 sqmm, with pvc insulated ( frls ) unsheathed multi stranded copper conductor cablefrls of size 2.5 sqmm as earth continuity wire to be drawn in and including pvc concealed conduit not less than 20 mm dia including with all accessories and fittings, fixed in concealed for one socket outlet 15 amp on independent board & including providing ms sheet metal sunken switch / terminal box 1.2mm thick and fittings for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surface, complete all as specified and directed.note : cutting chases and making good to match with the adjoining surface deemed to be included in the unit quoted rate. 159 s&f modular switch 1 way 5 / 6 amps, 1 module, 240 volts, isi marked, complete all as specified & directed. 160 s&f modular switch 1 way 15 / 16 amps, 1 module, 240 volts, isi marked, complete all as specified & directed. 161 s&f modular socket, 5 / 6 amps, 2 / 3 pin combined 2 module, 240 volts, isi marked, complete all as specified & directed. 162 s&f modular socket, 6a / 16a amps, 2 / 3 pin combined 2 module, 240 volts, isi marked, complete all as specified & directed. 163 s&f modular bell push, 5 / 6 amps, 1 module, 240 volts, isi marked, complete all as specified & directed. 164 s&f in renewal of modular fan step regulator, 120w 2 module, complete all as specified & directed. 165 s&f in renewal of buzzer, ding dong ac. 230 volts, single pole complete all as specified and directed. 166 s&f in renewal of modular metal flush box 8 module, isi marked, complete all as specified & directed. 167 s&f in renewal of modular metal flush box 6 module, isi marked, complete all as specified & directed. 168 s&f in renewal of modular metal flush box 3 module, isi marked, complete all as specified & directed. 169 s&f in renewal of modular metal flush box 1 / 2 module, isi marked, complete all as specified & directed. 170 s&f modular white cover plate with frame, 8 module, isi marked, complete all as specified & directed. 171 s&f modular white cover plate with frame, 6 module, isi marked, complete all as specified & directed. 172 s&f modular white cover plate with frame, 3 module, isi marked, complete all as specified & directed. 173 s&f modular white cover plate with frame, 2 module, isi marked, complete all as specified & directed. 174 s&f modular white cover plate with frame, 1 module, isi marked, complete all as specified & directed. 175 s&f switch piano flush type 5 / 6amps, 230 volts, single pole, one way, isi marked, complete all as specified & directed. 176 s&f switch piano flush type 5 / 6amps, 230 volts, single pole, two way, isi marked, complete all as specified & directed. 177 supply and fixingswitch socket combination, 5 / 6 and 15 / 16amps, 230 volt, multi pin, flush type universal, complete all as specified and directed. 178 supply and fixing socket outlet, 5 / 6 amps, 230 volt, five pin, flush type universal, complete all as specified and directed. 179 s&f pvc / polycarbonate lamp holder, angular / batten type with back plate, isi marked complete all as specified & directed. 180 s&f in renewal of stepped type electronic fan regulator, flush type, 230 volts ac, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed. 181 s&f ceiling rose surface type pvc / polycarbonate isolated body, 65x 50mm, 3 terminals, complete all as specified & directed. 182 s&f in renewal of wall mounted 20 watt led tube light fittings, 4 feet in length, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed. 183 s&f in renewal of wall mounted 10 watt led tube light fittings, 2 feet in length, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed. 184 s&f in renewal of led street light fitting 35 watt 230 v ac outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65 / 66 protection, complete all as specified and directed. 185 m & l in renewal of street / road light gi mounting bracket made out of steel tube, medium grade, 32 mm dia ( or higher size to suit the opening of the fitting ) 0.550 mtr long by hydraulic pressed mechine bend to require arc shape and fixed to pole with 02 nos ms flat iron clamps of suitable size fixed with bolts, nuts and washers including drilling holes and grouting with the same for fixing bolts as required & incl duly painted with two coat of aluminum paint over a coat of aluminum red oxide primer and fixing with lights fittings on the existing old street light poles complete all as specified and directed. note : cost of necessary tools and plants such as ladders, hydra for renewal of mounting brackets, light fittings, nuts, bolts etc shall be deemed to be included in the unit rate quoted. 186 s&f mcb, 6 to 32 amps, single pole, 240 volt, 10 ka c curve including all accessories, complete all as specified and directed. 187 s&f mcb, 40 to 63 amps, single pole & neutral, 240 volt, 10 ka c curve including all accessories, complete all as specified and directed. 188 s & f in renewal of single pole and neutral enclosure with a two pin and earth plug and socket complete with & including one single pole mcb of 20 amps complete, all as specified & directed. 189 s & f mccb 125 amps, 415 volts, four pole, c curve, adjustable type with rupturing capacity 36ka conforming to is 8828 1996, iec 60898 and testing for proper functioning complete, all as specified & directed. 190 s & f factory made verticle tpn db, 4 way, double door, ip 43, as per is 8623 iii, impact resistance ik 09 with the provision of 125 amp mccb 4 pole, 25 ka as incomer, 160 amp rated busbar, blanking plates with all electrical connection complete all as specified and directed.note for items of mcb db ( 1 ) the unit rate includes for cutting the brick / stone walls to accommodate db to make flush to wall. ( 2 ) the unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface. 191 s & f factory made mcb db made of sheet steel phosphatised, powder painted with bus bar 200 a, neutral link, earth bar and din rail, 240 volts spn with 8 ways, double door, complete all as specified and directed. 192 s & f factory made mcb db made of sheet steel phosphatised, powder painted with bus bar 200 a, neutral link, earth bar and din rail, 240 volts spn with 12 ways, double door, complete all as specified and directed. 193 s&f of concealed sub main wiring with two runs of single core pvc insulated and unsheathed frls multistranded copper conductor cable of size 10 sqmm lt, 1100 volts grade, drawn through and including 20 mm dia pvc nonmetallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 10 sqmm single core multistrandedfrls copper conductor cable green colour as earth continuity conductor, including all necessary wall cutting and making good disturbed surface complete all as specified & as directed. note for items of submain wiring: ( i ) cutting chases of stone masonary wall and making good to match with the adjoining surface deemed to be included in the unit quoted rate. ( ii ) two runs of cable one run of earth wire and one run of pvc non metallic conduit of 20mm dia shall be measured as one run length. ( iii ) cable required for connection to dbs shall deemed to be included and shall not be measured separately. ( iv ) earth wire shall run inside the pvc conduit. 194 s&f of concealed sub main wiring with two runs of single core pvc insulated and unsheathed frls multistranded copper conductor cable of size 6 sqmm lt, 1100 volts grade, drawn through and including 20 mm dia pvc nonmetallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistrandedfrls copper conductor cable green colour as earth continuity conductor, including all necessary wall cutting and making good disturbed surface complete all as specified & as directed. 195 s&f of concealed sub main wiring with two runs of single core pvc insulated and unsheathed frls multistranded copper conductor cable of size 4 sqmm lt, 1100 volts grade, drawn through and including 20 mm dia pvc nonmetallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 4 sqmm single core multistrandedfrls copper conductor cable green colour as earth continuity conductor, including all necessary wall cutting and making good disturbed surface complete all as specified & as directed. 196 m&l for earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground ( earth plate not less than 2.25 mtr below normal ground level ) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade gi tubing for protection of earth wire, ms sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 cm compacted thickness all around the electrode with concrete earth pit of pcc 1:3:6 type 75 mm thick precast rcc ( 1:2:4 ) type b1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft / loose soil and disposal of spolis to a distance not exc 50 mtr and necessary connection and testing complete all as shown in electrical plate no. 3 and including dismantling and taking out old earthing complete all as specified and directed.notes: ( a ) irrespective of whatever is shown in plate no 5 of ssr, earth pit shall be casted in pcc ( 1:3:6 ) type c 1 and precast cover of rcc ( 1:2:4 ) type b 1 with suitable handle. ( b ) item includes the cost of gi pipe for protection of earth wire and earth wire upto 7.5 m. any variation below or above shall be measured and paid for separately under relevant item of this sch ‘a’. 197 s&f in renewal of exhaust fan, steel body ac single phase. 230v of size 230mm, sweep with, blades, and frame and louvers & including connecting with and including pvc insulatedthree core 23 / .0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing mes no with black syntheticenamel paint 2.0 cm high and including making appropriate hole in the wall / window complete all as specified and directed. 198 s&f in renewal of exhaust fan, steel body ac single phase. 230v of size 300mm, sweep with, blades, and frame and louvers & including connecting with and including pvc insulatedthree core 23 / .0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing mes no with black syntheticenamel paint 2.0 cm high and including making appropriate hole in the wall / window complete all as specified and directed. 199 m & l for taking down carefully of serviceable geyser from its existing position by disconnecting all connection and keeping it in safe custody and refixing / re installation the same with nuts, bolts, fastnersand electrical connection etc., complete all as specified and directed. 200 s&f in renewal of hdpe pvc connection 600 mm long suitable for 15 mm gi pipe with two ptmt nuts and rubber washers complete all as specified and directed. 201 m & l for taking down carefully ceiling fans, exhaust fans, wall fanscomplete with blade and deposited it into mes stores & re fixing of the same to the specified locations and including connecting of ceiling rose with and including pvc insulatedthree core 23 / .0076 copper conductor cable, complete all as specified and directed....
Due Date : December 20, 2023
Tender Value : ₹ 37.80 Lakhs
