LNM Institute of Information Technology - Rajasthan

36414184 tender for “supply of it consumables”. , cat6 cable box, external dvd writer, fiber patch cord single mode sc sc (3 mtrs.) (10g and higher link supportable), fiber patch cord single mode sc lc (3 mtrs.) (10g and higher link supportable), fiber patch cord multimode sc lc (15 mtrs.) (10g and higher link supportable), 8 gb pen drive, rj 9 connector (4 pin), pvc insulation electrical tape(black, 1. 8cmx7mx0. 125mm), telephonecoil cord cable (2 mtr.) with rj 9 connector, telephoneline cord cable (3 mtr.) with rj 11 connector....

Rajasthan State Road Development And Construction Corporation Limited - Rajasthan

36350189 tender for electrification work of iti building at arain district ajmer wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 long point ( up to 10 mtr. ) 8 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 9 on board 10 short point ( up to 3 mtr. ) 11 medium point ( up to 6 mtr. ) 12 long point ( up to 10 mtr. ) 13 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 14 20 mm 15 25 mm 16 32 mm 17 40 mm 18 50 mm 19 s&f following sizesof isi marked ( is:14927 p ii ) virgin materialupvc trunking along with accessorieslike coupler, inner, outer, elbow, square box, tee, end cap etc. on surfacewithscrews, expansionfastenersas required. for additional technical parameters of product / work refer annexure a attached with this bsr 20 100 mm x 50 mm 21 150 mm x 50 mm 22 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 23 1 x 1.5 sq.mm 24 2 x 1.5 sq.mm 25 3x 1.5 sq.mm 26 1x 2.5 sq.mm 27 2 x 2.5 sq. mm. + 1x1.5sqmm 28 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 29 2 x 6.0 sq. mm. + 1 x 4.0 sq. mm. 30 2 x 6.0 sq.mm 31 2 x 4.0 sq.mm 32 4 x 10.0 sq.mm 33 4 x 16.0 sq.mm 34 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 35 2 pair 36 supply and laying of pe insulated jelly filledarmouredtelephone cable. with 0.6 mm thick solid annealed bare copper conductor and confirming to tec specificationsconfirming. to dot gr / cug 01 / aug.2003 in existing pipe / open trench / cable tray / on surface including making necessary connection, testing etc. as required of size. for additional technical parameters of product / work refer annexure a attached with this bsr 37 10 pair 38 50 pair 39 supplying and drawing coaxial cable 75 ohm impedance with foam pe insulated solid bare copper inner conductor, and ist outer conductor of bonded alum. tape and second outer conductor ofalum. alloy braidin existingsurface or recessed conduit / casing capping including making connections as required. for additional technical parameters of product / work refer annexure a attached with this bsr 40 rg 6 41 p / laying isi marked p.v.c. insulated submersible cable confirming to ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen freefor less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, existing pipe / open trench / cable tray / on surface including making connection etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 42 2.5 sq.mm 3 core flat / round 43 4.0 sq.mm 3 core flat / round 44 6.0 sq.mm 3 core flat / round 45 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 46 3.0 mm thick 47 4.8 mm thick 48 6.4 mm thick 49 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 50 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 51 10 pairs 52 50 pairs 53 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 54 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 55 20 amp, 3 pin + scrapping earth, 4 module 56 32 amp, 5 pin + scrapping earth, 8 module 57 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 58 up to 457 mm size 59 providing & fixing ofextra down rod of 15 mm dia . erw ( electrical resistance welded ) of 1.6mm nominal thick medium duty steelpipe including cutting, threading, drilling, fixing quarter pin etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 60 providing & fixing of single / multi tone electronic call bell as per pwd specification for electrical works, including making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 61 providing & fixing of modular type switch / bell push duly isi marked ( is :3854 ) with cm / l no. printed and made out of unbreakable and fire retardant vergin uv stabilized polycarbonatewith brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , minimum width ofswitch toggle ( push part ) should not less then 20mm, includingall as per pre approved by engineer in charge, making connections, testing etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 62 10 a one way switch 63 32 amp. 2 moduleswitch with ledindicator 64 providing & fixing of modular type lockable feature socket dulymade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 65 6 a3 / 5 pin shuttered socket 66 25 amp. 2 module socket 67 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 68 5 step fan regulator 2 module 360 dgree rotating 69 providing & fixing of following modular accessories as per pwd specification for electrical works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 70 t.v. coaxial socket 71 rj 11 telephone jack double line 72 blanking plate 73 modular mcb 6 a to 32 adp 74 providing & fixing offollowing size mounting grid plates with cover plates made from fire retardent uv established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 1 / 2 module 76 8 module 77 providing & fixing ofwiring accessories oem fabricated following size gi box of 1.2 mm thick with earthing terminal and adjustable floating clamp in recess / surface suitable for modular accessories as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 78 1 2 module 79 6 / 8 module 80 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminiumhousing with in built driver, system lumen efficacy = 110 lm / watt output, internal surge protection of 2.5 kv with short & open circuit protection , thd < 10% , p. f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 1170mm ( + / 10% ) led batten with min. lumen output 2200 lm 82 570mm ( + / 10% ) batten with min. lumen output 1000 lm 83 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 84 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 85 surface mounting ( with extruded alumn. housing ) 86 minimum lumen output 1300 lm 87 minimum lumen output 1950 lm 88 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 89 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 90 surface moutning 91 minimum lumen output 4200 lm 92 providing & fixing of ip65 ik08 rated integrated smd mid power led bulk head type light fixture made from pressure die cast al housing suitable with integral driver, system lumen efficacy =100 lm / watt output , thd < 10% , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. surge protection 4 kv. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 93 minimum lumen output 1000 lm 94 providing & fixing of 400 mm sweepbldc technology oscillating type wall mounting / pedestal typefans with three speed, on andoff position, double wall bearing withfront and back 120 or moreribs guard; three no.blades, noise level should be <= 75 db, including fixing with anchor bolts, making connection testing etc. as required. ( with remote ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 95 wall mounting type with service value 2.0 cmm / w, min. air delivery 71 cmm 96 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 97 1200 mm sweep bee 1 star rated ( service value >=4.0 to < 4.5 ) 98 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 300 mm sweep 100 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 300 mm sweep ( 900 / 1400 rpm ) 102 380 mm sweep ( 900 / 1400 rpm ) 103 providing & fixing ofof ventilating fans capacitor start, copper wounded, single phase with pvc impeller, abs body, automatic openable louver shutter in existing opening including making connection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 150 mm sweep 105 250 mm sweep 106 p & f of wall cowl with bird screen suitable for outside wall of exhaust fan openingof following size and made out from 24 swg gi sheet as per instructions of engineer in chargeincluding fixing with suitable fasteners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 107 suitable for 300 mm sweep exhaust fan 108 suitable for 380 mm sweep exhaust fan 109 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 110 led street light fixture with minimum lumen output 11225 lm 111 supply and erection ofgalvanized iron pole with galvanizing done in single dipping ( average coating thickness minimum 65 microns ) continuously tapered poles having octagonal / circular cross sections designed to withstand the maximum wind speed as per is 875, the pole shaft shall be made from sheet steel ( ht steel conforming to grade s355jo ) and confirming to bsen 10025 and shall be continuously tapered with single longitudinal welding. there shall not be any circumferential welding. the welding of pole shaft shall be done by submerged arc welding ( saw ) process. pole shafts shall be provided with the rigid flange plate of suitable thickness ( fe 410 conforming to is 226 / is 2062 ) with provision for fixing 4 no. foundation bolts, this base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside.the octagonal poles shall have lockable door of approximate 500 mm length at the elevation of 500 mm from the base plate with bakelite sheet having 6a sp mcb and 16 sqmm stud type connector ( 4 nos ) inside the pole at door opening for cable connection of following length and dimension as per table p 01 with base plate and foundation bolt on the existing cement concrete foundation.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 112 poles with octagonal cross section 113 7 mtr. 114 supply and fixing of pole oem fabricated hot dipped galvanised m.s. overhang ( 48.3 x 3.25 mm ) with cap ( 400 x 88.9 / 114.3 x 3.25 mm ) over the existing poles. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 single arm overhang 116 providing and laying rcc foundation for octagonal / conical street light poles, high mast poles as per drawing attach at tablep 4with following procedure& all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 a ) excavation of pit for foundation size upto required depth from ground level 118 b ) dressing of pit and dry stone pitching 200 mm thick including supply of stones and preparing surface complete. 119 c ) providing and laying in position cement concrete of m 10 grade of 75 mm thickness 120 d ) reinforcement for r.c.c. work with tmt bars including straightening, cutting, bending, placing in position and binding all complete. 121 e ) centring and shuttering including strutting , propping etc. and removal of form work for footing and pedestal 122 f ) providing & fixing of 2 no. required sizeplb hdpe pipe& foundation bolt with template as per oem recommendations. 123 g ) providing and layingreinforce cement concrete of m 25 grade in footing and pedestal including curing the foundation for 7 days. 124 h ) providing and fixing nosing angle 40 mm x 40 mm x 6mm with 2 no. 100 mm long, 10 mm dia. lugs on each face. 125 pole foundation for octagonal pole from 7 mtr. to 9 mtr. 126 providing & fixing of ik08ip65 protected top / bottom mounted led post top luminarie made of single piece constructionpowder coated die cast alluminium housing with uv stabalized clear / frosted polycarbonate diffuser andaluminium anodised with sand blast reflector. the system level luminous efficacy =100 lumen / w. smd leds is to be used, system cri>70, cct: 3000 / 4000 / 6500 k. the integral electronic driver must be potted & has a unique bis r number must be potted & has a unique bis r number constant current and internal / external surge protection device of min. 4kv ( l n ) and efficiency > 85%, pf>0.9, thd<10% and input voltage range of 140 270v ac at 50hz. system life of 50000 burning hours with 70% of initial lumens maintained . driver current <750ma.fixture must be in compliance with bis standards and trade mark certificate complete in all respect.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 127 minimum lumen output 4500 lm post top luminarie 128 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 129 40 mm dia. 130 supply , installation, testing and comissioning of is:1475 marked self contained drinking water cooler withhermeticallysealed compressor, non cfc refrigerent suitable for operation on 230v / 1ph / 50hz ac supply, full stainless steel ( ss304 ) body ( 0.8 mm thick ) and tank ( 0.5 mm thick ) , stainless steel water tray, minimum two nosbrass chrome plated faucets and suitable drainage system complete in all respect with requiredheight ms fabricated and painted angle iron frame ( cost of frame to be paid extra ) complete in all respect of the following capacity.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 131 cooling capacity 150 ltr. / hr. and storage capacity 150 ltrs 132 providing and laying non pressure np 3 classr.c.c. pipes including collars / spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) etc. as required. ( excavation of earth& back filling with compaction is to be paid extra ) . all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 200 mm dia. 134 labour charges for excavating trenches of required width for pipes dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 mtr.: 135 all kind of soils 136 sitc of wall type following zone ( each zoneaccessing minimum 20 units ( detectors / devices ) ) conventional type microprocessor based with lcd display en / lpcb / ul listed / approved main control panel fabricated from 16 swg crca sheet steel sealed maintenance free ( smf ) batteries of min2x7ah of 12 v or as required.including the cost of all accessories, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 4 zone 138 sitcof en / lpcb / ul listed / approved conventional type manual call point resettable complete with glass, hammer and chain etc.including the cost of all accessories etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 139 sitc of en / lpcb / ul listed / approved conventional type hooter cum strobe including the cost of all accessories, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 supply & fixing of water + afff 6%mechanical foam typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 25 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 141 capacity 6 ltrs. 142 supply & fixing of co2 type fire extinguisher conforming to is:15683:2018, charged with co2 gas ( purity 99.7% conforming to is 15222 ) , powder coated internal & external surface manganese steel isi marked as per is 7285 cylinder body , wheel type forged brass release valve isi marked as per is 3224 with inbuilt safety release device ( ( fusible plug and rupture disc type ) , 1.0 mtr. metal wire braided hose having minimum bursting pressure of 140 kgf / cm2, horn with metallic thread connection, qr code for product traceability, including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 143 capacity 4.5 kg. 144 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 4 kg 146 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 1.5 tr iseer not less then 4.6 148 2.0 tr iseer not less then 4.6 149 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 25 mm 151 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 4 kva 153 5 kva 154 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 155 50 mm dia per running inch length 156 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 157 sitc of interconnecting refrigerantcopper pipe forsplit / ductable / casseette ac of dhe grade c12200 astm b68, b75, chemical composition of copper % 99.0 min and phosphorus % 0.015 to 0.040 . for annealed copper tube : tensile strength = 210 mpa wih elongation % = 40 min . ink markbrand printing on hard tubes should be present. piping between each set of indoor & outdoor units of different sizesas per oem requirement & specifications including class o nitrile rubber sleeves, chase cutting, supports, making good the same with sand cement plaster etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 supplying and drawing flexible / stranded bare copper conductor, pvc / xlpe insulated, overall aluminium mylar tape shielded atc drain wire and outer pvc sheathed industrial instrumentation ( shielded ) cables voltage grade 300 / 500 v as per bs / en 50288 7 in existingsurface or recessed pvc / ms conduit / casing capping / cable tray / open duct making connections, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for cables. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 159 un armoured 160 4 core x 2.5 sq.mm 161 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 162 single pole mcb ( with b / c curve tripping characteristics ) 163 0.5 a to 5 a rating 164 6 a to 32 a rating 165 double pole mcb ( with b / c curve tripping characteristics ) 166 50 / 63 a rating 167 triple pole mcb ( with d curve tripping characteristics ) 168 6 a to 32 a rating 169 50 / 63 a rating 170 four pole mcb ( with b / c curve tripping characteristics ) 171 50 / 63 a rating 172 40 a rating 173 providing & fixing of 240 / 415 v residual current circuit breaker ( rccb ) conforming to ( is:12640 1 ) / iec 61008 1 , rated 4 kv impulse withstand voltage truly current operated and shall operate on cbct mechanisum, provision for pad lock, min. operation 10, 000 upto 63 a rating and5000 for 100 aratingand minimum phase termination capacity of 35 sq.mm. rigid wire, ip 20 contact protection with existing distribution board / sheetincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 174 two pole 100 / 300ma sensitivity 175 40 a rating 176 63 a rating 177 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 178 glazed door ( single phase ) ik 09 and ip 43 with metal end box 179 12 way ( 12+2 ) 180 metal door ( three phase ) per phase isolation, horizontal ik 09 and ip 43 with metal end box 181 4way ( incomer 8, sub incomer2+2+2 ) 182 6way ( incomer 8, sub incomer2+2+2 ) 183 8way ( incomer 8, sub incomer2+2+2 ) 184 12 way ( incomer 8, sub incomer2+2+2 ) 185 providing & fixing of recessed / surface mounting heavy duty vertical tpn distribution board with metal end box with provision of incomer suitable for 3 / 4 pole mccb and sp / tp mcb as outgoing , made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted with reversible door ( for double door db only ) complete with insulated 160 ( upto 160 a incomer ) / 250 amp. copper bus bar, neutral bars with shrouds, earth bar , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 186 double door ip 43 & ik 09 with provision of incomer mccb 100 / 125 a rating with metal end box 187 4 way 188 6 way 189 8 way 190 12 way 191 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 192 6.0 sq. mm 193 4 core 194 10.0 sq. mm 195 4 core 196 16.0 sq. mm 197 4 core 198 35.0 sq. mm 199 3.5 core 200 70.0 sq. mm 201 3.5 core 202 95.0 sq. mm 203 3.5 core 204 185.0 sq. mm 205 3.5 core 206 add extra for laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv gradedirect in ground including excavation of trench of size 75 cm ( depth ) x 35 cm ( width ) , with procedure as per followingpoints: ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay the cable in the middle of the trench, ( c ) provide river sand bed of height 125 mm on top of the cable, ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm widejust above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth 207 add extra for laying of one number additional pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv gradedirect in ground in the same trench in one tier horizontal formation including excavation of trench of size additional 20 cm in width, with procedure as per following points : ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay another cable in middle of trench in such manner that spacing between another cable is 20 cm., ( c ) provide river sand bed of height 125 mm on top of the cable. ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm widejust above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth. 208 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 209 3.5 x 185.0 sq.mm 210 3.5 x 95.0 sq.mm 211 3.5 x 70.0 sq.mm 212 3.5 x 35.0 sq.mm 213 4 x 16.0 sq.mm 214 4 x 10.0 sq.mm 215 4 x 6.0 sq.mm 216 supply, fabricating & installing following sizes of perforated hot dipped galvanized iron cable tray ( galvanized thickness not less then 50 microns ) with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers tees, cross members and other accessories as required and duly suspended from the ceiling with gi suspenders including gi bolts & nuts , fastners, supports etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 217 150mm x 50mm x 1.6mm 218 p / l of double wall corrugated hdpe pipe confirming to is : 16205 p 24, stiffness class750 n, externally corrugated and having smooth surface insidewith hdpe coupler, elbow, teeat required depth below the ground for laying cable of followingnominal outer dia.mfr test reportfrom nabl accrediated is to be submitted. ( excavation of earth& back filling with compaction is to be paid extra ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 219 50 mm 220 110 mm 221 plate earthing as per is:3043 withcopper earth plate of purity >95% of size 600mm x 600mm x 3.0mm by embodying3 mtr. below the ground level with 20mm dia. g.i. b class watering pipe , including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. and embodying the pipecomplete with alternate layers salt and coke / charcoal, testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 222 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 223 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 224 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 225 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 226 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 227 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 228 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 229 25 mm thick and 3 mtr. long 230 supply & laying following size earth stripin horizontal or vertical run in surface by means of earth strip dmc insulatorincluding riveting / soldering / welding, jointing shall be done by overlapping and with 2 set of brass ( for cu strip ) / gi ( for gi strip ) nut bolt & spring washer spaced at 50cm making connection etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 231 25mm x 3mm g.i. ( hot dipped ) strip 232 50mm x 6mm g.i. ( hot dipped ) strip 233 40mm x 6mm copper strip 234 supply & laying following size b class , g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with accessories like bend, socket etc.for laying earth conductor / strip / cable in ground / surface / recess as required.all as per pre approved by engineer in charge. ( earth excavation will be paid extra ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annex ure a attached with this bsr . 235 50 mm dia. 236 65 mm dia. 237 80 mm dia. 238 100 mm dia. 239 150 mm dia. 240 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 241 8 swg g.i. ( hot dipped ) wire 242 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 243 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 244 cat 6, un sheilded information outlet 245 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 246 single aperture 247 supply, installation, testing and comissioning of rack mounted 19 1u, cat6 24 port loaded, 1.5 1.6 mm crs chasis, powder coated, sheet steel, made of plastic ( abs ) , modular patch panelswith rear cable management system and mounting hardware to mount the patch panel. should have port identification numbers printed / engraved on front of the panel. etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 248 modular patch panel loaded with cat 6 i / o 249 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 250 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 251 1 mtr 252 2 mtr 253 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 254 15 u rack with width 600 mm & depth 400 mm + 100 mm 255 supply & installation of ip 20 & ik 08 , ul listed communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, vertical mounting rail 1.6 mm with umarking, front sturdy sheet steel frame folded from one piece and welded with 5mm toughened glass door, with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, set of 75 mm height 4 castors, 2 of which have brakes, accessories like: 5 nos of 19 1u horizontal cable manager, 2 nos of vertical cable managers, 1 no. keyboard tray, 4 nos of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 2 no of 19 1u, mountable socket strips with 6 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 256 27 u rack with width 600 mm &depth 800 mm 257 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 258 providing & laying xlpe insulated three core armouredaluminiumcable for working voltage 11 k.v. ( e ) confirming is :7098 p 2withh4 grade electrolyticaluminium conductor confirming to is: 8130 class 2 of purity >99.6 %, insulation screening: extruded semiconducting compound followed by helically wrapped copper tape, round / flat strip armouring of cables , inner / outer sheath pvc type st 2 confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810 all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 259 3 core 185.0 sq.mm 260 add extra for laying of one number xlpe power cable of 11 / 33 kv ( earthed ) voltage gradedirect in ground including excavation of trench of size 120 cm ( depth ) x 35 cm ( width ) , with procedure as per followingpoints: ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay the cable in the middle of the trench, ( c ) provide river sand bed of height 125 mm on top of the cable. ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm wide just above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth 261 providing & making heat shrinkable type indoor / outdoor / straight through terminations / joint kitsuitable for11 kv / 33 kv ( earthed ) cable with required components, prepration of cable ends. type test report should be as per is13573:2011 which covered all sequence for table 2 for termination kit and table 3 for streightthrough joint inclusive thermal & dynamic short circuit test, humidity test, soil fog test. crosslinking shall be done out side factory with e beam / peroxide technology. extrusion process shall be in house oem within same vicinity. includingtesting etc. as required of following sizes. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 262 11 kv end termination kit indoor type 263 3 core 120 / 150 / 185 sq.mm 264 11 kv end termination kit outdoor type 265 3 core 120 / 150 / 185 sq.mm 266 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 267 open execution type 268 200 a 269 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 270 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 271 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 272 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 273 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 274 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 275 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 276 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 277 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 278 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 279 electrolytic grade aluminium bus bar 6010 grade 280 providing & fixing of is: 13875 & iec :61326 confirming led digital type ( up to 500 ) v range volt meter / direct ammeter / ct oertated ammeter / frequency meter / kwh meter / multi function meter / power analyzer of class 1 accuracyas per is : 1248 of size 96mm x 96 mm including making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 281 threephase amp+hz+pf+kw+kva+kvar+t.energy+thd i, thd v & run hrs 282 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 283 ring type tape wound ct 284 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 285 c t class 1, ratio 400 / 5 to 1200 / 5, burden 15 va 286 providing & fixing ofcam operated rotary ( auto / manual ) switches on existing panel with 2 way and off position using high grade engineering materialto international standards with cam assemblyinsulation of glass filled polyamide with high tracking index. for reliable and stable electrical and mechanical endurance double butt contacts with silver bi metal on copper should provided . contact assembly is of operating temp range 25 degree c to 55 degree c, frequency upto 10 khz. switch life under std. op. conditions shall be mechanically minimum 50000 operations @300 cycles / hour and electrically 10, 000 operations at 100% rated duty for 100 cycles / hour including making connection etc.as required . all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 287 32 amp 288 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 289 red / yellow / green colour 290 blue / white colour 291 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 292 11 kv, class b 2.5 mm thick with proof voltage 22 kv ac ( rms ) and break down voltage45 kv ac ( rms ) 293 providing & fixing of self healing ip20 mpp type shunt capacitor ( banks ) conforming to is:13340 41 / iec :831 1&2 or iec : 60831 1& 2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( psd ) and shall have dissipation factor less than 0.0025 at 50 hz, operating loss less than 0.30 watt per kvar. min over current capacity 1.8 times rated current & peak inrush current min. 300 times of rated current, llife expectancy greater than 100000hrs ( temp class 25 d ) in 440 v / 480 v capacitor and for 525 v should life expectancy minimum 1, 65, 000 hrs ( temp class 25 d ) including making connections, testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 294 heavy dutythree phase 525v, 50 hzcylindrical typecapacitor ( bank ) 295 providing & fixing of ip54 microprocessor based 3 ct’s for all 3 phasesensing compensationpower factor correction relay size 139mm x 139 mm, operating voltage 415 / 440 v, iec / en 61000 6 ( 2&4 ) having 3 ct sensing, sensitivity up to 50 milli amp secondary current , self analysing auto c / k setting according to targeted power factor setting, the relay shall havedigit display unit for display of real power factor, targeted power factor, lag / lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with rs 485, indication of switching on units, auto / manual status, and shall have over load protection, no volt release , having multi parameter like kw, kva, kvar, rms value, step switching time 2 sec to 1800 sec. lead & lag parameters, metering facility and3 no. class 0.5 cast resinct ( refer ct specs in this chapter ) for sensing the relay including making coonection with 1.5 sq.mm copper wire etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 296 12 to 14 stage 297 providing & fixing ofac operated heavy duty 230 / 440 volt power contactor as per pwd specification for electrical works, isi marked is / iec 60947 4 1 : 2000 having provision of mechanical interlocking, auxilary contacts, din rail mounting type including making connections, testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 298 3 pole power contactorswith following ac 3 rating 299 40 amp 300 providing & fixing of440 volt 3 pole capacitor ( ac 6 b ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors / reactors to limit the inrush current as per pwd specification for electrical works, is / iec 60947 4 1 : 2000, insulation voltage 1000v, impulse withstand voltage 8 kv, din rail mounting type including making connections, testing etc. as required. suitable for following capacity capacitor bank.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 301 up to 6 kvar 302 10 kvar 303 20.0 kvar 304 providing & fixing of mechanical / digital time switch having following day / week programme and minimum 100 hours reserve and ac1 rating of 16 20 amperes including making connection, programming conforming to iec 60730 1 and 60730 2 7 etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 305 one day & week reserve ( digital type ) 306 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 307 3 pole mccb with thermal magnetic release 308 160 amp , 25 ka, adjustable o / l & adjustable s / c setting, 309 4 pole mccb with thermal magnetic release 310 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 311 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 312 160 amp , 25 ka, adjustable o / l & adjustable s / c setting, 313 200 amp , 25 ka, adjustable o / l & adjustable s / c setting, 314 250 amp , 35 ka, adjustable o / l & adjustable s / c setting, 315 400 amp , 35 ka, adjustable o / l & adjustable s / c setting, 316 s i t c of star ratedaluminium wound distribution transformerof following rating 11 / 0.433kv delta star connected, vector group dyn 11, onan cooled & as per bee star 1 & bis approved as per is 2026 1977 & lossesas defined as per 2014 ( fourth revision ) level 1 . including standardaccessories like conservator, silica gel breather, radiator, fins, ht cable box & lt cable boxes, temperature rise in winding / oil 35 40 degree c upto 200 kva & 40 45 degree c for above 200 kva, isi marked drain valve, dial type temperature gauge, first filling of transformer oil as per is :335 1953, epoxy based paint, including carrying of pre commission testing & charging of transformer complete in all respect . 317 the transformer shall be subjected to routine factory tests ( as per is:2026 and is:1180 ) including testing from ctlof discombefore charging of transformer & complete installaion must be certified from electrical inspectorate office as per indian electricity rule, ( ctl testing charges and electrical inspection charges shall be reimbursed by the department to the contractor ) . all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 318 250 kva with off ltc ( +5% to 10% @ 2.5% ) 319 sitc of 11kv 630 amps 21ka for 3 sec. sf6 insulated, outdoor duty ( ip54 ) , extensible / non extensible typering main unit ( rmu ) manually operated in combination ofvcb modules andload break switch consisting of copper busbar in sf6 insulated 304 ( non ferrite non magnetic grade ) stainless steel enclosure of thickness 2.5mm with manometer.the hv switchgear and control gear should be confirming to iec 62271 100, iec 62271 200 2003 & iec 60694 1996. the rmu should be internal arc tested for 21ka for 1second with iac afl classification for gas tank. vacum interrupter of vcb should be rmu manufacturer’s own make.each feeder of rmu should have voltage presence indicator. . and compring offollowings: 1 no. microprocessor based self powered numerical relay with over current / earth fault & short circuit protection with each vcb feeder. 3 nos. protection ct shall be of burden 2.5va, ratio 50 / 1a, class of accuracy class 5p10for o / c and e / f protection for each vcb. 1 no. manometer for each tank, 1 nos. fault passage indicator, right angle boots for all the feeder modulesall the type test certificates as per iec from third partynabl / cpri / erda accrediated lab to be submitted. ( cost of rcc foundation / steel structure to be paid extra ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr 320 non extensible 3 way rmu with 1 no. vcb & 2 no. load break switch 321 sitc of ht metering cubical panel as approved by discoms fabricated out of 18 swg crca sheet steel in two compartment & ms angle of size 60mmx 6mm having provision for following: ( i ) provision for fixing trivector / import export meter ( to be supplied by discoms ) ( ii ) provision for fixing of combined ct pt set with copper strip for connection ( to be supplied by discoms ) , ( iii ) test terminal block, ( iv ) 6mm thick bakelite sheet on all sides, ( v ) 3 / 6 corex 1.5 / 2.5 sq.mm copper cable for interconnections, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 322 sitc of radiator cooled and turbo charged silent dg set ( as per latest cpcb emissionnorms ) havingspecifications as per a, b, c, d, e, f, g, h & i 323 a ) 1500 rpm diesel engine conforming to bs:649 / 5514 of suitable bhp ( up to 82.5 kva 6 cylinder or below required, 125 kva & above ratings 6 cylinder or aboverequired ) capable of taking 10% over loading for one hour after 12 hours of continuous operation., dry exhaust mainfold with hospital grade silencer and catalytic convertor ( isolated from main dg chamber ) , up to 3 m exhaust piping ( with lrb insulation & alum. cladding ) as required . 324 b ) ac brush less spdp alternator conform to bs 5000 ( part 99 ) or is / iec 60034 1. . alternator shall be self regulated with standard alternator protection ( over voltage , over speed & under voltage, under speed warning & shutdown ) .engine & alternator mounted on a common base frame & coupled through a flexible coupling or close coupled 325 c ) cpcb / arai approved standard canopy with weatherproof, powdercoated accoustic enclosure for dg set for sound attenuation fabricated from 1.6 mm crca sheet steel ( structure ) with sidewall fabricated from 1.6 mm crca sheet & filled with glasswool ( 96kg / m3 ) / foam. as per is8183 the doors of 28 / 40 / 50 / 85mm thick as perrating and fabricated from 1.6mm crca sheet packed with accoustic material, all doors / opening are sealed with neoprene / epdngaskets. the dg set has inbuilt / external in fuel tank to run 6 to 8 hrs as per oem standard, with protection and tripping of dg set against temperature of more than 50 degree centigrade. 326 d ) electronic / mechanical governor, manual & electric start , batteries with battry charger, engine instruments panel, avm pads all controls for operation of dg set are from outside the enclosure with dg control panel having microprocessor based genset monitoring like running hour, rpm, low lube oil tripping & control system, panel mounted mccb / acb of suitable rating, ammeter, voltmeter, pf meter, frequency meter, kwh meter, digital fuel display meter, ind.lamps etc. mounted inside enclosure , visible and accessible from outside. the enclosure should be suitable for following capacity dg sets and alternator. noise level shall be less than 75 db at a distance of 1 mtrs. duly certified by authorised agency etc. complete in all respect of following capacity : 327 e ) ( i ) accoustic glass wool wall thickness should not be less then 40mm and not less then 20mm pu foam upto rating 100 kva. ( ii ) .accoustic glass wool wall thickness should not be less then 65mm and not less then 50mm pu foam upto rating 250 kva. ( iii ) accoustic glass wool wall thickness should not be less then 100mm forrating above 250 kva. 328 f ) first filling of the fuel tank shall be done by contractor and the prevailing fuel cost at that time shall be reimbursed to the contactor by department. 329 g ) servicing contract of dg set from oems authorised service dealer as per oem guidelines during the dlp period shall be done by contractor including all consumables, actual charges shall be reimbursed to the contractor by end user department. 330 h ) manufacturer / oem must have its authorized service dealer in rajasthan. which can provide service within 6 hours of compalint registration. 331 i ) dg set will be offered for inspection and testing at manufacturers works in presence of departmental engineers. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 332 40 kva at 0.8 pf 415v 50hz 3 ? 333 sitc of plc based auto main failure ( amf ) panel fabricated from crca sheet steel 2 mmthick , powder coated finish , engine start & stopcommands, control relays , ammeter & voltmeterwith selector switches, control & 2 nos 4 pole power contactors with 2 no. of required size 4 pole mccb, timers, electronic hooter , visual & alarm indication for faults, ups, operator interface panel complete in all respect suitable for following capacity dg sets: appropriate test certificate / report of product / accessories from oem / panel manufecturer shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 334 20 to 40 kva 335 supply & fabrication steel structure with ms channel / angle / joist / ismb / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as requiredcomplete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 336 providing and fixing welded mesh / expanded metal mesh 25 mmx 25 mm x 3mm in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. including two coat of red oxide and two coat of enamel paint or more requiredcomplete with frame work with 50 x 50 x 6mm angle iron post 30 cm in ground embeded in cement concrete 1:3:6 ( 30x30x45cm ) at corner and every three mtr including painting with one coat of primer and two coat of enamel paint work will be done as per direction of engineer incharge of sizecomplete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 337 earth work in excavation / by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5m in width as well as 10 sum on plan ) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed: 338 random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 ( 1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size ) upto plinth level with cement mortar 1:6 ( 1 cement : 6 sand ) . 339 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level 340 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) 341 plaster on new surface on wall in cement sand mortar 1:4 including racking of joints etc. complete fine finish : 342 20mm thick 343 finishing wall with water proofing cement paint of approved brand and manufacture and or required shadetogive an even shade including all scaffolding: 344 new work ( two or more coats applied @ 3.84 kg / 10 sqm ) . 345 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 346 5.0 hp, 3 ø, ( 14 28 ) mtr, ( 995 500 ) lpm 347 sitc of contactoroem fabricated dol / star delta starter panel with switchgear selection as per type 2 cordinatiom chart andmade out from 1.6 mm thick powder coated crca sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, illuminated on / offpush buttons, ammeter, voltmeter, indicating lamps etc.suitable for following rating motors complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 348 for three phase submersible / mono block pump 349 3.0 hp to 5.0 hp ( dol starter ) 350 part b non bsr items based on market rate 351 sitc ofro water system with filtration stage = particulate filter membrane life enhancer filter sediment filter pre carbon filter ro membrane filter post carbon filter, input power rating 230 v ac , 50 hz, percentage of rejection tds 90% or better having following features ( a ) double purification by ro with ess or latest technology with tds indicator ( b ) .spin welded ro membrane housing to prevent tempering ( c ) . push fit components for leak proof performance ( d ) . fully automatic operation with auto start and auto off ( e ) . ss construction for corrosion free lifespan ( f ) . equally suitable for water from all bore wells, , overhead storage tanks, water tankers and even municipal taps ( g ) ro membrane flushing auto flush @ every start , every stop and every one hourof working for one minute. complete in all respect with following capacity. approved make:eureka forbes, kent, au smith, ion exchange, pentair. 352 purification capacity 50 lph, duty cycle 270 500 liters / day, 353 sitc of dome ip ir cctv cameras: network h.265 2mp ( full hd ) megapixel high frame rate mini dome camera with built in microphone:2mp ir dome camera with metal body and built in mic: 1 / 2.8 progressive scan cmos; resolution: 1920 × 1080@30fps or better; colour: 0.01 lux @ ( f1.2, agc on ) or better, h.265+ compression or better; 120 db true wdr or better; fixed 2.8 / 4mm lens; built in mic; 3d dnr; 40m ir range or better, triple streams; blc, 3d dnr, hlc; line crossing detection, intrusion detection; scene change detection; face detection; anti flicker, heartbeat, mirror, password protection, privacy mask, watermark, ip address filter; onvif ( profile s, profile g ) , isapi; built in micro sd / sdhc / sdxc slot, up to 128 gb or better; operating condition: 30 °c to +60 °c; ip67; 12dc & poe; certificate of compliance: ul, ce / fcc, bis, rohsapproved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 354 sitc of ip ir cctv bullet outdoor camera: network h.265 2mp ( full hd ) megapixel high frame rate ir bullet camera ( outdoor ) with metal body, 2mp full frame low light ir bullet camera: 1 / 2.5 progressive scan cmos; resolution: 1920 × 1080 or better; color: 0.002 lux @ ( f1.2, agc on ) or better; slow shutter; fixed 3.6 mm lens; triple streams; 3d dnr; 120db wdr; 50m ir range or better; line crossing detection, intrusion detection, object removal detection, unattended baggage detection, scene change detection; face detection; anti flicker, heartbeat, mirror, password protection, privacy mask, watermark, ip address filter; onvif ( profile s, profile g ) , isapi; roi; support micro sd / sdhc / sdxc card ( 128g ) , local storage and nas ( nfs, smb / cifs ) , anr; operating condition: 30 °c to +60 °c; ip67; 12dc & poe; metal body; built in junction box for cable management; certificate of compliance: ul, ce / fcc, bis / rohs approved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 355 sitc of raid 5 supported 32ch nvr with upto 48 tb hdd support 32ch ip inputs; dual os for redundancy; support anr technology;320mbps incoming bandwidth, supports up to 12mp full channel recording; support h.265 compression; 16ch syncronised playback @1080p; support raid 5; n+1 hot spare system; support 3rd party cameras; 4k output; minimum 8 sata hdd slots; each slot should suppport upto 6tb hdd; e sata interface; dual gigabit self adaptive ethernet interface; serial interace; usb interface; alarm in / out;dual power supply ( all cameras and storage nvr should be of same make for the smooth functioning of the system ) . certificate of compliance: ul, ce / fcc, bisapproved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 356 sitc of 3.5 6tb surveillance hard disk ( makes: seagate / wd / toshiba ) 357 sitc of workstation latest intel® i5 processor, with 17 led monitor screen intel chipset motherboard, 08 gb ram, 1 tb sata hdd at 7200 rpm, with 4gb gpu type higher end graphic card for h.265 compression technique with dual display ports / dvi / hdmi port, giga lan card, wireless keyboard, wireless optical mouse with original license windows software of approved makes: lenovo, hp, dell. 358 sitc of 55 flat smart screen hd profesional led with remote control and wall mount unit / floor stand complete with making connections etc of approved makes: lg, samsung, panasonic. 359 sitc of 5 kva 1 phase input, 1 phase output advance dsp controlled ups with igbt based rectifier, lcd display, double conversion / digital signal processing ups, with isolationtransformer, with 26ahx x 16 nos smf batteries for min 30 min back up, with ms rack for barreries and required cabling for incoming & outgoing connection of approved makes: numeric, eaton, emerson, apc. 360 supply, installation, testing & commissioning of managed layer 2 intelligent ethernet poe switches providing 08 x 10 / 100 / 1000 fast ethernet poe ports 67w or better and 2 dual purpose uplink ports ( provision for copper / fiber giga connectivity ) all switches & related fiber modules should be of same make & category for seamless integration with each other of approved makes: cisco catalyst series or equivalent in avaya, juniper ) 361 p & f of early streamer emission type lightning arrester on gi mast with air terminal configured as spheroid which is comprised ofseparate electrically isolated 4 panels surrounding an earthed central finial, the terminal shall be tested by cpri for impulse current of 45 ka ( 8 / 20 sec ) with 5 positive & 5 negative impulse, the arrester having following protection radius at level 1 approved makes :lpi ( australia ) , lpsfr ( france ) , sudafix ( uk ) , ef ( switzerland ) , abb 362 30 48 mtr. 363 s & laying of p.v.c. / xlpe insulated & p.v.c. sheathed down conductor of 70 sq.mm single core insulated flexible copper cable confirming to is:1554 p i / is :7098 p i of 1.1 kv withelectrolytic gradecopper made of copper rodsconfirming to is 613 1964, of purity >99.7 %, inner / outer sheath confirming to is:5831 with accessories as required. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810approved makes: polycab, rr, finolex....

Rajasthan State Road Development And Construction Corporation Limited - Rajasthan

36348916 tender for electrification work of iti building at kareda district bhilwara wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 long point ( up to 10 mtr. ) 8 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 9 on board 10 short point ( up to 3 mtr. ) 11 medium point ( up to 6 mtr. ) 12 long point ( up to 10 mtr. ) 13 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 14 20 mm 15 25 mm 16 32 mm 17 40 mm 18 50 mm 19 s&f following sizesof isi marked ( is:14927 p ii ) virgin materialupvc trunking along with accessorieslike coupler, inner, outer, elbow, square box, tee, end cap etc. on surfacewithscrews, expansionfastenersas required. for additional technical parameters of product / work refer annexure a attached with this bsr 20 100 mm x 50 mm 21 150 mm x 50 mm 22 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 23 1 x 1.5 sq.mm 24 2 x 1.5 sq.mm 25 3x 1.5 sq.mm 26 1x 2.5 sq.mm 27 2 x 2.5 sq. mm. + 1x1.5sqmm 28 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 29 2 x 6.0 sq. mm. + 1 x 4.0 sq. mm. 30 2 x 6.0 sq.mm 31 2 x 4.0 sq.mm 32 4 x 10.0 sq.mm 33 4 x 16.0 sq.mm 34 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 35 2 pair 36 supply and laying of pe insulated jelly filledarmouredtelephone cable. with 0.6 mm thick solid annealed bare copper conductor and confirming to tec specificationsconfirming. to dot gr / cug 01 / aug.2003 in existing pipe / open trench / cable tray / on surface including making necessary connection, testing etc. as required of size. for additional technical parameters of product / work refer annexure a attached with this bsr 37 10 pair 38 50 pair 39 supplying and drawing coaxial cable 75 ohm impedance with foam pe insulated solid bare copper inner conductor, and ist outer conductor of bonded alum. tape and second outer conductor ofalum. alloy braidin existingsurface or recessed conduit / casing capping including making connections as required. for additional technical parameters of product / work refer annexure a attached with this bsr 40 rg 6 41 p / laying isi marked p.v.c. insulated submersible cable confirming to ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen freefor less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, existing pipe / open trench / cable tray / on surface including making connection etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 42 2.5 sq.mm 3 core flat / round 43 4.0 sq.mm 3 core flat / round 44 6.0 sq.mm 3 core flat / round 45 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 46 3.0 mm thick 47 4.8 mm thick 48 6.4 mm thick 49 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 50 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 51 10 pairs 52 50 pairs 53 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 54 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 55 20 amp, 3 pin + scrapping earth, 4 module 56 32 amp, 5 pin + scrapping earth, 8 module 57 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 58 up to 457 mm size 59 providing & fixing ofextra down rod of 15 mm dia . erw ( electrical resistance welded ) of 1.6mm nominal thick medium duty steelpipe including cutting, threading, drilling, fixing quarter pin etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 60 providing & fixing of single / multi tone electronic call bell as per pwd specification for electrical works, including making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 61 providing & fixing of modular type switch / bell push duly isi marked ( is :3854 ) with cm / l no. printed and made out of unbreakable and fire retardant vergin uv stabilized polycarbonatewith brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , minimum width ofswitch toggle ( push part ) should not less then 20mm, includingall as per pre approved by engineer in charge, making connections, testing etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 62 10 a one way switch 63 32 amp. 2 moduleswitch with ledindicator 64 providing & fixing of modular type lockable feature socket dulymade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 65 6 a3 / 5 pin shuttered socket 66 25 amp. 2 module socket 67 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 68 5 step fan regulator 2 module 360 dgree rotating 69 providing & fixing of following modular accessories as per pwd specification for electrical works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 70 t.v. coaxial socket 71 rj 11 telephone jack double line 72 blanking plate 73 modular mcb 6 a to 32 adp 74 providing & fixing offollowing size mounting grid plates with cover plates made from fire retardent uv established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 1 / 2 module 76 8 module 77 providing & fixing ofwiring accessories oem fabricated following size gi box of 1.2 mm thick with earthing terminal and adjustable floating clamp in recess / surface suitable for modular accessories as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 78 1 2 module 79 6 / 8 module 80 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminiumhousing with in built driver, system lumen efficacy = 110 lm / watt output, internal surge protection of 2.5 kv with short & open circuit protection , thd < 10% , p. f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 1170mm ( + / 10% ) led batten with min. lumen output 2200 lm 82 570mm ( + / 10% ) batten with min. lumen output 1000 lm 83 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 84 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 85 surface mounting ( with extruded alumn. housing ) 86 minimum lumen output 1300 lm 87 minimum lumen output 1950 lm 88 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 89 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 90 surface moutning 91 minimum lumen output 4200 lm 92 providing & fixing of ip65 ik08 rated integrated smd mid power led bulk head type light fixture made from pressure die cast al housing suitable with integral driver, system lumen efficacy =100 lm / watt output , thd < 10% , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. surge protection 4 kv. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 93 minimum lumen output 1000 lm 94 providing & fixing of 400 mm sweepbldc technology oscillating type wall mounting / pedestal typefans with three speed, on andoff position, double wall bearing withfront and back 120 or moreribs guard; three no.blades, noise level should be <= 75 db, including fixing with anchor bolts, making connection testing etc. as required. ( with remote ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 95 wall mounting type with service value 2.0 cmm / w, min. air delivery 71 cmm 96 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 97 1200 mm sweep bee 1 star rated ( service value >=4.0 to < 4.5 ) 98 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 300 mm sweep 100 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 300 mm sweep ( 900 / 1400 rpm ) 102 380 mm sweep ( 900 / 1400 rpm ) 103 providing & fixing ofof ventilating fans capacitor start, copper wounded, single phase with pvc impeller, abs body, automatic openable louver shutter in existing opening including making connection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 150 mm sweep 105 250 mm sweep 106 p & f of wall cowl with bird screen suitable for outside wall of exhaust fan openingof following size and made out from 24 swg gi sheet as per instructions of engineer in chargeincluding fixing with suitable fasteners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 107 suitable for 300 mm sweep exhaust fan 108 suitable for 380 mm sweep exhaust fan 109 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 110 led street light fixture with minimum lumen output 11225 lm 111 supply and erection ofgalvanized iron pole with galvanizing done in single dipping ( average coating thickness minimum 65 microns ) continuously tapered poles having octagonal / circular cross sections designed to withstand the maximum wind speed as per is 875, the pole shaft shall be made from sheet steel ( ht steel conforming to grade s355jo ) and confirming to bsen 10025 and shall be continuously tapered with single longitudinal welding. there shall not be any circumferential welding. the welding of pole shaft shall be done by submerged arc welding ( saw ) process. pole shafts shall be provided with the rigid flange plate of suitable thickness ( fe 410 conforming to is 226 / is 2062 ) with provision for fixing 4 no. foundation bolts, this base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside.the octagonal poles shall have lockable door of approximate 500 mm length at the elevation of 500 mm from the base plate with bakelite sheet having 6a sp mcb and 16 sqmm stud type connector ( 4 nos ) inside the pole at door opening for cable connection of following length and dimension as per table p 01 with base plate and foundation bolt on the existing cement concrete foundation.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 112 poles with octagonal cross section 113 7 mtr. 114 supply and fixing of pole oem fabricated hot dipped galvanised m.s. overhang ( 48.3 x 3.25 mm ) with cap ( 400 x 88.9 / 114.3 x 3.25 mm ) over the existing poles. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 single arm overhang 116 providing and laying rcc foundation for octagonal / conical street light poles, high mast poles as per drawing attach at tablep 4with following procedure& all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 a ) excavation of pit for foundation size upto required depth from ground level 118 b ) dressing of pit and dry stone pitching 200 mm thick including supply of stones and preparing surface complete. 119 c ) providing and laying in position cement concrete of m 10 grade of 75 mm thickness 120 d ) reinforcement for r.c.c. work with tmt bars including straightening, cutting, bending, placing in position and binding all complete. 121 e ) centring and shuttering including strutting , propping etc. and removal of form work for footing and pedestal 122 f ) providing & fixing of 2 no. required sizeplb hdpe pipe& foundation bolt with template as per oem recommendations. 123 g ) providing and layingreinforce cement concrete of m 25 grade in footing and pedestal including curing the foundation for 7 days. 124 h ) providing and fixing nosing angle 40 mm x 40 mm x 6mm with 2 no. 100 mm long, 10 mm dia. lugs on each face. 125 pole foundation for octagonal pole from 7 mtr. to 9 mtr. 126 providing & fixing of ik08ip65 protected top / bottom mounted led post top luminarie made of single piece constructionpowder coated die cast alluminium housing with uv stabalized clear / frosted polycarbonate diffuser andaluminium anodised with sand blast reflector. the system level luminous efficacy =100 lumen / w. smd leds is to be used, system cri>70, cct: 3000 / 4000 / 6500 k. the integral electronic driver must be potted & has a unique bis r number must be potted & has a unique bis r number constant current and internal / external surge protection device of min. 4kv ( l n ) and efficiency > 85%, pf>0.9, thd<10% and input voltage range of 140 270v ac at 50hz. system life of 50000 burning hours with 70% of initial lumens maintained . driver current <750ma.fixture must be in compliance with bis standards and trade mark certificate complete in all respect.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 127 minimum lumen output 4500 lm post top luminarie 128 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 129 40 mm dia. 130 supply , installation, testing and comissioning of is:1475 marked self contained drinking water cooler withhermeticallysealed compressor, non cfc refrigerent suitable for operation on 230v / 1ph / 50hz ac supply, full stainless steel ( ss304 ) body ( 0.8 mm thick ) and tank ( 0.5 mm thick ) , stainless steel water tray, minimum two nosbrass chrome plated faucets and suitable drainage system complete in all respect with requiredheight ms fabricated and painted angle iron frame ( cost of frame to be paid extra ) complete in all respect of the following capacity.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 131 cooling capacity 150 ltr. / hr. and storage capacity 150 ltrs 132 providing and laying non pressure np 3 classr.c.c. pipes including collars / spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) etc. as required. ( excavation of earth& back filling with compaction is to be paid extra ) . all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 200 mm dia. 134 labour charges for excavating trenches of required width for pipes dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 mtr.: 135 all kind of soils 136 sitc of wall type following zone ( each zoneaccessing minimum 20 units ( detectors / devices ) ) conventional type microprocessor based with lcd display en / lpcb / ul listed / approved main control panel fabricated from 16 swg crca sheet steel sealed maintenance free ( smf ) batteries of min2x7ah of 12 v or as required.including the cost of all accessories, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 4 zone 138 sitcof en / lpcb / ul listed / approved conventional type manual call point resettable complete with glass, hammer and chain etc.including the cost of all accessories etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 139 sitc of en / lpcb / ul listed / approved conventional type hooter cum strobe including the cost of all accessories, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 supply & fixing of water + afff 6%mechanical foam typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 25 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 141 capacity 6 ltrs. 142 supply & fixing of co2 type fire extinguisher conforming to is:15683:2018, charged with co2 gas ( purity 99.7% conforming to is 15222 ) , powder coated internal & external surface manganese steel isi marked as per is 7285 cylinder body , wheel type forged brass release valve isi marked as per is 3224 with inbuilt safety release device ( ( fusible plug and rupture disc type ) , 1.0 mtr. metal wire braided hose having minimum bursting pressure of 140 kgf / cm2, horn with metallic thread connection, qr code for product traceability, including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 143 capacity 4.5 kg. 144 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 4 kg 146 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 1.5 tr iseer not less then 4.6 148 2.0 tr iseer not less then 4.6 149 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 25 mm 151 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 4 kva 153 5 kva 154 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 155 50 mm dia per running inch length 156 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 157 sitc of interconnecting refrigerantcopper pipe forsplit / ductable / casseette ac of dhe grade c12200 astm b68, b75, chemical composition of copper % 99.0 min and phosphorus % 0.015 to 0.040 . for annealed copper tube : tensile strength = 210 mpa wih elongation % = 40 min . ink markbrand printing on hard tubes should be present. piping between each set of indoor & outdoor units of different sizesas per oem requirement & specifications including class o nitrile rubber sleeves, chase cutting, supports, making good the same with sand cement plaster etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 supplying and drawing flexible / stranded bare copper conductor, pvc / xlpe insulated, overall aluminium mylar tape shielded atc drain wire and outer pvc sheathed industrial instrumentation ( shielded ) cables voltage grade 300 / 500 v as per bs / en 50288 7 in existingsurface or recessed pvc / ms conduit / casing capping / cable tray / open duct making connections, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for cables. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 159 un armoured 160 4 core x 2.5 sq.mm 161 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 162 single pole mcb ( with b / c curve tripping characteristics ) 163 0.5 a to 5 a rating 164 6 a to 32 a rating 165 double pole mcb ( with b / c curve tripping characteristics ) 166 50 / 63 a rating 167 triple pole mcb ( with d curve tripping characteristics ) 168 6 a to 32 a rating 169 50 / 63 a rating 170 four pole mcb ( with b / c curve tripping characteristics ) 171 50 / 63 a rating 172 40 a rating 173 providing & fixing of 240 / 415 v residual current circuit breaker ( rccb ) conforming to ( is:12640 1 ) / iec 61008 1 , rated 4 kv impulse withstand voltage truly current operated and shall operate on cbct mechanisum, provision for pad lock, min. operation 10, 000 upto 63 a rating and5000 for 100 aratingand minimum phase termination capacity of 35 sq.mm. rigid wire, ip 20 contact protection with existing distribution board / sheetincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 174 two pole 100 / 300ma sensitivity 175 40 a rating 176 63 a rating 177 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 178 glazed door ( single phase ) ik 09 and ip 43 with metal end box 179 12 way ( 12+2 ) 180 metal door ( three phase ) per phase isolation, horizontal ik 09 and ip 43 with metal end box 181 4way ( incomer 8, sub incomer2+2+2 ) 182 6way ( incomer 8, sub incomer2+2+2 ) 183 8way ( incomer 8, sub incomer2+2+2 ) 184 12 way ( incomer 8, sub incomer2+2+2 ) 185 providing & fixing of recessed / surface mounting heavy duty vertical tpn distribution board with metal end box with provision of incomer suitable for 3 / 4 pole mccb and sp / tp mcb as outgoing , made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted with reversible door ( for double door db only ) complete with insulated 160 ( upto 160 a incomer ) / 250 amp. copper bus bar, neutral bars with shrouds, earth bar , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 186 double door ip 43 & ik 09 with provision of incomer mccb 100 / 125 a rating with metal end box 187 4 way 188 6 way 189 8 way 190 12 way 191 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 192 6.0 sq. mm 193 4 core 194 10.0 sq. mm 195 4 core 196 16.0 sq. mm 197 4 core 198 35.0 sq. mm 199 3.5 core 200 70.0 sq. mm 201 3.5 core 202 95.0 sq. mm 203 3.5 core 204 185.0 sq. mm 205 3.5 core 206 add extra for laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv gradedirect in ground including excavation of trench of size 75 cm ( depth ) x 35 cm ( width ) , with procedure as per followingpoints: ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay the cable in the middle of the trench, ( c ) provide river sand bed of height 125 mm on top of the cable, ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm widejust above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth 207 add extra for laying of one number additional pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv gradedirect in ground in the same trench in one tier horizontal formation including excavation of trench of size additional 20 cm in width, with procedure as per following points : ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay another cable in middle of trench in such manner that spacing between another cable is 20 cm., ( c ) provide river sand bed of height 125 mm on top of the cable. ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm widejust above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth. 208 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 209 3.5 x 185.0 sq.mm 210 3.5 x 95.0 sq.mm 211 3.5 x 70.0 sq.mm 212 3.5 x 35.0 sq.mm 213 4 x 16.0 sq.mm 214 4 x 10.0 sq.mm 215 4 x 6.0 sq.mm 216 supply, fabricating & installing following sizes of perforated hot dipped galvanized iron cable tray ( galvanized thickness not less then 50 microns ) with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers tees, cross members and other accessories as required and duly suspended from the ceiling with gi suspenders including gi bolts & nuts , fastners, supports etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 217 150mm x 50mm x 1.6mm 218 p / l of double wall corrugated hdpe pipe confirming to is : 16205 p 24, stiffness class750 n, externally corrugated and having smooth surface insidewith hdpe coupler, elbow, teeat required depth below the ground for laying cable of followingnominal outer dia.mfr test reportfrom nabl accrediated is to be submitted. ( excavation of earth& back filling with compaction is to be paid extra ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 219 50 mm 220 110 mm 221 plate earthing as per is:3043 withcopper earth plate of purity >95% of size 600mm x 600mm x 3.0mm by embodying3 mtr. below the ground level with 20mm dia. g.i. b class watering pipe , including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. and embodying the pipecomplete with alternate layers salt and coke / charcoal, testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 222 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 223 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 224 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 225 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 226 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 227 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 228 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 229 25 mm thick and 3 mtr. long 230 supply & laying following size earth stripin horizontal or vertical run in surface by means of earth strip dmc insulatorincluding riveting / soldering / welding, jointing shall be done by overlapping and with 2 set of brass ( for cu strip ) / gi ( for gi strip ) nut bolt & spring washer spaced at 50cm making connection etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 231 25mm x 3mm g.i. ( hot dipped ) strip 232 50mm x 6mm g.i. ( hot dipped ) strip 233 40mm x 6mm copper strip 234 supply & laying following size b class , g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with accessories like bend, socket etc.for laying earth conductor / strip / cable in ground / surface / recess as required.all as per pre approved by engineer in charge. ( earth excavation will be paid extra ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annex ure a attached with this bsr . 235 50 mm dia. 236 65 mm dia. 237 80 mm dia. 238 100 mm dia. 239 150 mm dia. 240 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 241 8 swg g.i. ( hot dipped ) wire 242 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 243 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 244 cat 6, un sheilded information outlet 245 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 246 single aperture 247 supply, installation, testing and comissioning of rack mounted 19 1u, cat6 24 port loaded, 1.5 1.6 mm crs chasis, powder coated, sheet steel, made of plastic ( abs ) , modular patch panelswith rear cable management system and mounting hardware to mount the patch panel. should have port identification numbers printed / engraved on front of the panel. etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 248 modular patch panel loaded with cat 6 i / o 249 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 250 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 251 1 mtr 252 2 mtr 253 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 254 15 u rack with width 600 mm & depth 400 mm + 100 mm 255 supply & installation of ip 20 & ik 08 , ul listed communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, vertical mounting rail 1.6 mm with umarking, front sturdy sheet steel frame folded from one piece and welded with 5mm toughened glass door, with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, set of 75 mm height 4 castors, 2 of which have brakes, accessories like: 5 nos of 19 1u horizontal cable manager, 2 nos of vertical cable managers, 1 no. keyboard tray, 4 nos of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 2 no of 19 1u, mountable socket strips with 6 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 256 27 u rack with width 600 mm &depth 800 mm 257 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 258 providing & laying xlpe insulated three core armouredaluminiumcable for working voltage 11 k.v. ( e ) confirming is :7098 p 2withh4 grade electrolyticaluminium conductor confirming to is: 8130 class 2 of purity >99.6 %, insulation screening: extruded semiconducting compound followed by helically wrapped copper tape, round / flat strip armouring of cables , inner / outer sheath pvc type st 2 confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810 all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 259 3 core 185.0 sq.mm 260 add extra for laying of one number xlpe power cable of 11 / 33 kv ( earthed ) voltage gradedirect in ground including excavation of trench of size 120 cm ( depth ) x 35 cm ( width ) , with procedure as per followingpoints: ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay the cable in the middle of the trench, ( c ) provide river sand bed of height 125 mm on top of the cable. ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm wide just above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth 261 providing & making heat shrinkable type indoor / outdoor / straight through terminations / joint kitsuitable for11 kv / 33 kv ( earthed ) cable with required components, prepration of cable ends. type test report should be as per is13573:2011 which covered all sequence for table 2 for termination kit and table 3 for streightthrough joint inclusive thermal & dynamic short circuit test, humidity test, soil fog test. crosslinking shall be done out side factory with e beam / peroxide technology. extrusion process shall be in house oem within same vicinity. includingtesting etc. as required of following sizes. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 262 11 kv end termination kit indoor type 263 3 core 120 / 150 / 185 sq.mm 264 11 kv end termination kit outdoor type 265 3 core 120 / 150 / 185 sq.mm 266 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 267 open execution type 268 200 a 269 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 270 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 271 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 272 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 273 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 274 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 275 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 276 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 277 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 278 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 279 electrolytic grade aluminium bus bar 6010 grade 280 providing & fixing of is: 13875 & iec :61326 confirming led digital type ( up to 500 ) v range volt meter / direct ammeter / ct oertated ammeter / frequency meter / kwh meter / multi function meter / power analyzer of class 1 accuracyas per is : 1248 of size 96mm x 96 mm including making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 281 threephase amp+hz+pf+kw+kva+kvar+t.energy+thd i, thd v & run hrs 282 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 283 ring type tape wound ct 284 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 285 c t class 1, ratio 400 / 5 to 1200 / 5, burden 15 va 286 providing & fixing ofcam operated rotary ( auto / manual ) switches on existing panel with 2 way and off position using high grade engineering materialto international standards with cam assemblyinsulation of glass filled polyamide with high tracking index. for reliable and stable electrical and mechanical endurance double butt contacts with silver bi metal on copper should provided . contact assembly is of operating temp range 25 degree c to 55 degree c, frequency upto 10 khz. switch life under std. op. conditions shall be mechanically minimum 50000 operations @300 cycles / hour and electrically 10, 000 operations at 100% rated duty for 100 cycles / hour including making connection etc.as required . all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 287 32 amp 288 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 289 red / yellow / green colour 290 blue / white colour 291 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 292 11 kv, class b 2.5 mm thick with proof voltage 22 kv ac ( rms ) and break down voltage45 kv ac ( rms ) 293 providing & fixing of self healing ip20 mpp type shunt capacitor ( banks ) conforming to is:13340 41 / iec :831 1&2 or iec : 60831 1& 2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( psd ) and shall have dissipation factor less than 0.0025 at 50 hz, operating loss less than 0.30 watt per kvar. min over current capacity 1.8 times rated current & peak inrush current min. 300 times of rated current, llife expectancy greater than 100000hrs ( temp class 25 d ) in 440 v / 480 v capacitor and for 525 v should life expectancy minimum 1, 65, 000 hrs ( temp class 25 d ) including making connections, testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 294 heavy dutythree phase 525v, 50 hzcylindrical typecapacitor ( bank ) 295 providing & fixing of ip54 microprocessor based 3 ct’s for all 3 phasesensing compensationpower factor correction relay size 139mm x 139 mm, operating voltage 415 / 440 v, iec / en 61000 6 ( 2&4 ) having 3 ct sensing, sensitivity up to 50 milli amp secondary current , self analysing auto c / k setting according to targeted power factor setting, the relay shall havedigit display unit for display of real power factor, targeted power factor, lag / lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with rs 485, indication of switching on units, auto / manual status, and shall have over load protection, no volt release , having multi parameter like kw, kva, kvar, rms value, step switching time 2 sec to 1800 sec. lead & lag parameters, metering facility and3 no. class 0.5 cast resinct ( refer ct specs in this chapter ) for sensing the relay including making coonection with 1.5 sq.mm copper wire etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 296 12 to 14 stage 297 providing & fixing ofac operated heavy duty 230 / 440 volt power contactor as per pwd specification for electrical works, isi marked is / iec 60947 4 1 : 2000 having provision of mechanical interlocking, auxilary contacts, din rail mounting type including making connections, testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 298 3 pole power contactorswith following ac 3 rating 299 40 amp 300 providing & fixing of440 volt 3 pole capacitor ( ac 6 b ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors / reactors to limit the inrush current as per pwd specification for electrical works, is / iec 60947 4 1 : 2000, insulation voltage 1000v, impulse withstand voltage 8 kv, din rail mounting type including making connections, testing etc. as required. suitable for following capacity capacitor bank.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 301 up to 6 kvar 302 10 kvar 303 20.0 kvar 304 providing & fixing of mechanical / digital time switch having following day / week programme and minimum 100 hours reserve and ac1 rating of 16 20 amperes including making connection, programming conforming to iec 60730 1 and 60730 2 7 etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 305 one day & week reserve ( digital type ) 306 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 307 3 pole mccb with thermal magnetic release 308 160 amp , 25 ka, adjustable o / l & adjustable s / c setting, 309 4 pole mccb with thermal magnetic release 310 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 311 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 312 160 amp , 25 ka, adjustable o / l & adjustable s / c setting, 313 200 amp , 25 ka, adjustable o / l & adjustable s / c setting, 314 250 amp , 35 ka, adjustable o / l & adjustable s / c setting, 315 400 amp , 35 ka, adjustable o / l & adjustable s / c setting, 316 s i t c of star ratedaluminium wound distribution transformerof following rating 11 / 0.433kv delta star connected, vector group dyn 11, onan cooled & as per bee star 1 & bis approved as per is 2026 1977 & lossesas defined as per 2014 ( fourth revision ) level 1 . including standardaccessories like conservator, silica gel breather, radiator, fins, ht cable box & lt cable boxes, temperature rise in winding / oil 35 40 degree c upto 200 kva & 40 45 degree c for above 200 kva, isi marked drain valve, dial type temperature gauge, first filling of transformer oil as per is :335 1953, epoxy based paint, including carrying of pre commission testing & charging of transformer complete in all respect . 317 the transformer shall be subjected to routine factory tests ( as per is:2026 and is:1180 ) including testing from ctlof discombefore charging of transformer & complete installaion must be certified from electrical inspectorate office as per indian electricity rule, ( ctl testing charges and electrical inspection charges shall be reimbursed by the department to the contractor ) . all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 318 250 kva with off ltc ( +5% to 10% @ 2.5% ) 319 sitc of 11kv 630 amps 21ka for 3 sec. sf6 insulated, outdoor duty ( ip54 ) , extensible / non extensible typering main unit ( rmu ) manually operated in combination ofvcb modules andload break switch consisting of copper busbar in sf6 insulated 304 ( non ferrite non magnetic grade ) stainless steel enclosure of thickness 2.5mm with manometer.the hv switchgear and control gear should be confirming to iec 62271 100, iec 62271 200 2003 & iec 60694 1996. the rmu should be internal arc tested for 21ka for 1second with iac afl classification for gas tank. vacum interrupter of vcb should be rmu manufacturer’s own make.each feeder of rmu should have voltage presence indicator. . and compring offollowings: 1 no. microprocessor based self powered numerical relay with over current / earth fault & short circuit protection with each vcb feeder. 3 nos. protection ct shall be of burden 2.5va, ratio 50 / 1a, class of accuracy class 5p10for o / c and e / f protection for each vcb. 1 no. manometer for each tank, 1 nos. fault passage indicator, right angle boots for all the feeder modulesall the type test certificates as per iec from third partynabl / cpri / erda accrediated lab to be submitted. ( cost of rcc foundation / steel structure to be paid extra ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr 320 non extensible 3 way rmu with 1 no. vcb & 2 no. load break switch 321 sitc of ht metering cubical panel as approved by discoms fabricated out of 18 swg crca sheet steel in two compartment & ms angle of size 60mmx 6mm having provision for following: ( i ) provision for fixing trivector / import export meter ( to be supplied by discoms ) ( ii ) provision for fixing of combined ct pt set with copper strip for connection ( to be supplied by discoms ) , ( iii ) test terminal block, ( iv ) 6mm thick bakelite sheet on all sides, ( v ) 3 / 6 corex 1.5 / 2.5 sq.mm copper cable for interconnections, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 322 sitc of radiator cooled and turbo charged silent dg set ( as per latest cpcb emissionnorms ) havingspecifications as per a, b, c, d, e, f, g, h & i 323 a ) 1500 rpm diesel engine conforming to bs:649 / 5514 of suitable bhp ( up to 82.5 kva 6 cylinder or below required, 125 kva & above ratings 6 cylinder or aboverequired ) capable of taking 10% over loading for one hour after 12 hours of continuous operation., dry exhaust mainfold with hospital grade silencer and catalytic convertor ( isolated from main dg chamber ) , up to 3 m exhaust piping ( with lrb insulation & alum. cladding ) as required . 324 b ) ac brush less spdp alternator conform to bs 5000 ( part 99 ) or is / iec 60034 1. . alternator shall be self regulated with standard alternator protection ( over voltage , over speed & under voltage, under speed warning & shutdown ) .engine & alternator mounted on a common base frame & coupled through a flexible coupling or close coupled 325 c ) cpcb / arai approved standard canopy with weatherproof, powdercoated accoustic enclosure for dg set for sound attenuation fabricated from 1.6 mm crca sheet steel ( structure ) with sidewall fabricated from 1.6 mm crca sheet & filled with glasswool ( 96kg / m3 ) / foam. as per is8183 the doors of 28 / 40 / 50 / 85mm thick as perrating and fabricated from 1.6mm crca sheet packed with accoustic material, all doors / opening are sealed with neoprene / epdngaskets. the dg set has inbuilt / external in fuel tank to run 6 to 8 hrs as per oem standard, with protection and tripping of dg set against temperature of more than 50 degree centigrade. 326 d ) electronic / mechanical governor, manual & electric start , batteries with battry charger, engine instruments panel, avm pads all controls for operation of dg set are from outside the enclosure with dg control panel having microprocessor based genset monitoring like running hour, rpm, low lube oil tripping & control system, panel mounted mccb / acb of suitable rating, ammeter, voltmeter, pf meter, frequency meter, kwh meter, digital fuel display meter, ind.lamps etc. mounted inside enclosure , visible and accessible from outside. the enclosure should be suitable for following capacity dg sets and alternator. noise level shall be less than 75 db at a distance of 1 mtrs. duly certified by authorised agency etc. complete in all respect of following capacity : 327 e ) ( i ) accoustic glass wool wall thickness should not be less then 40mm and not less then 20mm pu foam upto rating 100 kva. ( ii ) .accoustic glass wool wall thickness should not be less then 65mm and not less then 50mm pu foam upto rating 250 kva. ( iii ) accoustic glass wool wall thickness should not be less then 100mm forrating above 250 kva. 328 f ) first filling of the fuel tank shall be done by contractor and the prevailing fuel cost at that time shall be reimbursed to the contactor by department. 329 g ) servicing contract of dg set from oems authorised service dealer as per oem guidelines during the dlp period shall be done by contractor including all consumables, actual charges shall be reimbursed to the contractor by end user department. 330 h ) manufacturer / oem must have its authorized service dealer in rajasthan. which can provide service within 6 hours of compalint registration. 331 i ) dg set will be offered for inspection and testing at manufacturers works in presence of departmental engineers. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 332 40 kva at 0.8 pf 415v 50hz 3 ? 333 sitc of plc based auto main failure ( amf ) panel fabricated from crca sheet steel 2 mmthick , powder coated finish , engine start & stopcommands, control relays , ammeter & voltmeterwith selector switches, control & 2 nos 4 pole power contactors with 2 no. of required size 4 pole mccb, timers, electronic hooter , visual & alarm indication for faults, ups, operator interface panel complete in all respect suitable for following capacity dg sets: appropriate test certificate / report of product / accessories from oem / panel manufecturer shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 334 20 to 40 kva 335 supply & fabrication steel structure with ms channel / angle / joist / ismb / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as requiredcomplete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 336 providing and fixing welded mesh / expanded metal mesh 25 mmx 25 mm x 3mm in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. including two coat of red oxide and two coat of enamel paint or more requiredcomplete with frame work with 50 x 50 x 6mm angle iron post 30 cm in ground embeded in cement concrete 1:3:6 ( 30x30x45cm ) at corner and every three mtr including painting with one coat of primer and two coat of enamel paint work will be done as per direction of engineer incharge of sizecomplete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 337 earth work in excavation / by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5m in width as well as 10 sum on plan ) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed: 338 random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 ( 1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size ) upto plinth level with cement mortar 1:6 ( 1 cement : 6 sand ) . 339 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level 340 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) 341 plaster on new surface on wall in cement sand mortar 1:4 including racking of joints etc. complete fine finish : 342 20mm thick 343 finishing wall with water proofing cement paint of approved brand and manufacture and or required shadetogive an even shade including all scaffolding: 344 new work ( two or more coats applied @ 3.84 kg / 10 sqm ) . 345 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 346 5.0 hp, 3 ø, ( 14 28 ) mtr, ( 995 500 ) lpm 347 sitc of contactoroem fabricated dol / star delta starter panel with switchgear selection as per type 2 cordinatiom chart andmade out from 1.6 mm thick powder coated crca sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, illuminated on / offpush buttons, ammeter, voltmeter, indicating lamps etc.suitable for following rating motors complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 348 for three phase submersible / mono block pump 349 3.0 hp to 5.0 hp ( dol starter ) 350 part b non bsr items based on market rate 351 sitc ofro water system with filtration stage = particulate filter membrane life enhancer filter sediment filter pre carbon filter ro membrane filter post carbon filter, input power rating 230 v ac , 50 hz, percentage of rejection tds 90% or better having following features ( a ) double purification by ro with ess or latest technology with tds indicator ( b ) .spin welded ro membrane housing to prevent tempering ( c ) . push fit components for leak proof performance ( d ) . fully automatic operation with auto start and auto off ( e ) . ss construction for corrosion free lifespan ( f ) . equally suitable for water from all bore wells, , overhead storage tanks, water tankers and even municipal taps ( g ) ro membrane flushing auto flush @ every start , every stop and every one hourof working for one minute. complete in all respect with following capacity. approved make:eureka forbes, kent, au smith, ion exchange, pentair. 352 purification capacity 50 lph, duty cycle 270 500 liters / day, 353 sitc of dome ip ir cctv cameras: network h.265 2mp ( full hd ) megapixel high frame rate mini dome camera with built in microphone:2mp ir dome camera with metal body and built in mic: 1 / 2.8 progressive scan cmos; resolution: 1920 × 1080@30fps or better; colour: 0.01 lux @ ( f1.2, agc on ) or better, h.265+ compression or better; 120 db true wdr or better; fixed 2.8 / 4mm lens; built in mic; 3d dnr; 40m ir range or better, triple streams; blc, 3d dnr, hlc; line crossing detection, intrusion detection; scene change detection; face detection; anti flicker, heartbeat, mirror, password protection, privacy mask, watermark, ip address filter; onvif ( profile s, profile g ) , isapi; built in micro sd / sdhc / sdxc slot, up to 128 gb or better; operating condition: 30 °c to +60 °c; ip67; 12dc & poe; certificate of compliance: ul, ce / fcc, bis, rohsapproved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 354 sitc of ip ir cctv bullet outdoor camera: network h.265 2mp ( full hd ) megapixel high frame rate ir bullet camera ( outdoor ) with metal body, 2mp full frame low light ir bullet camera: 1 / 2.5 progressive scan cmos; resolution: 1920 × 1080 or better; color: 0.002 lux @ ( f1.2, agc on ) or better; slow shutter; fixed 3.6 mm lens; triple streams; 3d dnr; 120db wdr; 50m ir range or better; line crossing detection, intrusion detection, object removal detection, unattended baggage detection, scene change detection; face detection; anti flicker, heartbeat, mirror, password protection, privacy mask, watermark, ip address filter; onvif ( profile s, profile g ) , isapi; roi; support micro sd / sdhc / sdxc card ( 128g ) , local storage and nas ( nfs, smb / cifs ) , anr; operating condition: 30 °c to +60 °c; ip67; 12dc & poe; metal body; built in junction box for cable management; certificate of compliance: ul, ce / fcc, bis / rohs approved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 355 sitc of raid 5 supported 32ch nvr with upto 48 tb hdd support 32ch ip inputs; dual os for redundancy; support anr technology;320mbps incoming bandwidth, supports up to 12mp full channel recording; support h.265 compression; 16ch syncronised playback @1080p; support raid 5; n+1 hot spare system; support 3rd party cameras; 4k output; minimum 8 sata hdd slots; each slot should suppport upto 6tb hdd; e sata interface; dual gigabit self adaptive ethernet interface; serial interace; usb interface; alarm in / out;dual power supply ( all cameras and storage nvr should be of same make for the smooth functioning of the system ) . certificate of compliance: ul, ce / fcc, bisapproved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 356 sitc of 3.5 6tb surveillance hard disk ( makes: seagate / wd / toshiba ) 357 sitc of workstation latest intel® i5 processor, with 17 led monitor screen intel chipset motherboard, 08 gb ram, 1 tb sata hdd at 7200 rpm, with 4gb gpu type higher end graphic card for h.265 compression technique with dual display ports / dvi / hdmi port, giga lan card, wireless keyboard, wireless optical mouse with original license windows software of approved makes: lenovo, hp, dell. 358 sitc of 55 flat smart screen hd profesional led with remote control and wall mount unit / floor stand complete with making connections etc of approved makes: lg, samsung, panasonic. 359 sitc of 5 kva 1 phase input, 1 phase output advance dsp controlled ups with igbt based rectifier, lcd display, double conversion / digital signal processing ups, with isolationtransformer, with 26ahx x 16 nos smf batteries for min 30 min back up, with ms rack for barreries and required cabling for incoming & outgoing connection of approved makes: numeric, eaton, emerson, apc. 360 supply, installation, testing & commissioning of managed layer 2 intelligent ethernet poe switches providing 08 x 10 / 100 / 1000 fast ethernet poe ports 67w or better and 2 dual purpose uplink ports ( provision for copper / fiber giga connectivity ) all switches & related fiber modules should be of same make & category for seamless integration with each other of approved makes: cisco catalyst series or equivalent in avaya, juniper ) 361 p & f of early streamer emission type lightning arrester on gi mast with air terminal configured as spheroid which is comprised ofseparate electrically isolated 4 panels surrounding an earthed central finial, the terminal shall be tested by cpri for impulse current of 45 ka ( 8 / 20 sec ) with 5 positive & 5 negative impulse, the arrester having following protection radius at level 1 approved makes :lpi ( australia ) , lpsfr ( france ) , sudafix ( uk ) , ef ( switzerland ) , abb 362 30 48 mtr. 363 s & laying of p.v.c. / xlpe insulated & p.v.c. sheathed down conductor of 70 sq.mm single core insulated flexible copper cable confirming to is:1554 p i / is :7098 p i of 1.1 kv withelectrolytic gradecopper made of copper rodsconfirming to is 613 1964, of purity >99.7 %, inner / outer sheath confirming to is:5831 with accessories as required. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810approved makes: polycab, rr, finolex....

Indo Tibetan Border Police - Rajasthan

36250231 bids are invited for lan accessories utp cat 6 cable box 305 meter per box , information outlets cat6 single port , cat 6 patch panel 24 port , utp cat6 patch cord sm sc lc 1 mtrs , utp patch cord sm sc lc 2 mtrs , ofc patch cord sm sc lc 3 mtrs , fiber optical cable single mode outdoor armoured 12 core , sc pigtails , liu 12 port 19 rack mount , liu 24 port 19 rack mount , 19 9u wall mount rack with all the accessories , 19 42u rack with all the accessories , 15 15 mm pvc duct , 25 25 mm pvc duct , 25 45 mm pvc duct , 25mm pvc conduit pipe , 2 diameter hdpe pvc , fiber optic cable route marker , buffer tubing kit , layer 2 manageable 24 port switch 10 100 1000 mbps with additional 2 sfp ports 5 years warranty , layer 3 manageable 24 port switch 10 100 1000 mbps with additional 6 sfp ports 5 years warranty 10 100 1000 mbps with additional 6 sfp ports 5 years warranty , 1000 base lx transceivers with lc connector sm 5 years warranty , 1000 base lx transceivers for copper 5 years warranty , stacking module of 10 gbps with stacking cable 5 years warranty total quantity : 4202...

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

36168355 tender for supply of electronics & hardware combination pliers , diagonal cuttin pliers , long nose pliers , hand drill , electric drill upto 10mm , hacksaw , wire stripper , soldering iron ( 10w / 25w ) , adjustable wrench , ball pein hammer , line tester , double ended spanner set , instrument files , chisels set , vice , vice , tweezer , pcb drill , pincer , magnifying glass , hammer , de soldering pump , 1 desktop computer , multi meter , mixer, juicer & grinder , radiation leakage tester , lcd tds meter , microwave oven , printer with scanner , water purifier , gloves , safety helmet , safety shoes , fire extinguisher , oscilloscope , rubber matt , electronics & hardware lab consumables ( recurring items list ) , resistors , capacitors , coiis ( aluminium ) , transistors , ic / ic sockets , led , transformers , ribbon cable , upt cat.5 cables ( box ) , upt cat. 3 cables ( box ) , connecting lead , sockest , jacks & plugs ( each set ) , connecting plugs , drill bits , soldering iron bit , soldering ironelements / wax / wire , silicon paste , machine oil , swithces ( each set ) , screws & nuts ( as per need ) , fuses , brushes , wire brushes , frist aid kit , power transistor bases , insulating tape , rj 45 , steel ruler , ruler , safety googles , anti static wrist , crimping tools , t square , display charts & learning manuals , learning , work instructions , hand outs , schematic diagrams , charts , block diagrams , layout plans , location plans , instrumentation diagrams , loop diagrams , system control diagrams...

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

36166485 tender for supply of telecom material combination pliers , diagonal cuttin pliers , long nose pliers , hand drill , electric drill upto 10mm , hacksaw , wire stripper , soldering iron ( 10w / 25w ) , adjustable wrench , ball pein hammer , line tester , double ended spanner set , instrument files , chisels set , vice , vice , tweezer , pcb drill , pincer , magnifying glass , hammer , de soldering pump , 1 desktop computer , multi meter , mixer, juicer & grinder , radiation leakage tester , lcd tds meter , microwave oven , printer with scanner , water purifier , gloves , safety helmet , safety shoes , fire extinguisher , oscilloscope , rubber matt , electronics & hardware lab consumables ( recurring items list ) , resistors , capacitors , coiis ( aluminium ) , transistors , ic / ic sockets , led , transformers , ribbon cable , upt cat.5 cables ( box ) , upt cat. 3 cables ( box ) , connecting lead , sockest , jacks & plugs ( each set ) , connecting plugs , drill bits , soldering iron bit , soldering ironelements / wax / wire , silicon paste , machine oil , swithces ( each set ) , screws & nuts ( as per need ) , fuses , brushes , wire brushes , frist aid kit , power transistor bases , insulating tape , rj 45 , steel ruler , ruler , safety googles , anti static wrist , crimping tools , t square , display charts & learning manuals , learning , work instructions , hand outs , schematic diagrams , charts , block diagrams , layout plans , location plans , instrumentation diagrams , loop diagrams , system control diagrams...

North Western Railway - Rajasthan

36151981 supply of rc for kbi make spares for coaches, overhauling kit for dump valve to kbi part no 34652 / 15024 for lhb coaches of 07 items. s. no. 1. o ring a40125 / 6 02 nos. 2. o ring b31807 02 nos. 3 o ring a40125 / 2 02 nos. 4 o ring a91150 02 nos. 5. o ring b57679 02 nos. 6 strainer c62814 02 nos. 7 sealing ring 465372 01 nos. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 960.00 set ajmer , nwr , overhawling kit for check valve to kbi part no. 190476 for lhb coaches consisting of 03 items sn. 1 o ring k3581 1 nos. 2. o ring k4140 3 nos. 3. valve sealing disc 468676 1 nos. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 480.00 set ajmer , nwr , circut board eb01 for wsp system of lhb coaches kbi part no. stn 25799 / 01 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 16.00 numbers , circuit board pb03 a for wsp system of lhb coaches kbi part no. stn 25089 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 16.00 numbers , circut board mb 04b for wsp systemof lhb coaches. kbi part no.stn 28339 / 00000 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 11.00 numbers , distributor valve ke11pksl with suitable relay valve & mounting bkt ( lhb ) kbi part no i.2.765 & i.2.724. distributor valv offer accepted as e kedipksl with pressure convertor for lhb to kbi part no. i.2.765 and mounting bracket to kbi part no. i.2.724. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 15.00 numbers , speed sensor g16 to kbi part no. stn31450 / 205a 18u with 2 meters long cable only integral with speed sensor as per rdso spec no rdso / 2011 / cg 04 ( rev 1 ) with amendment no 1 appendix f. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 88.00 numbers ajmer , nwr , check valve rv7 t kbi part no 190476 for lhb coaches. [ warranty period: 30 months after the date of delivery ] page 2 of 11 run date / time: 08 / 02 / 2023 16:15:58stores / north western rly tender document , filter nw 19 with code pin for lhb coaches. part no. m / s knorr bremse wbfil 100aa002 special terms and conditions. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 15.00 numbers , brake caliper unit leverage ratio 2.17 without brake cylinder for lhb fiat bogie eog coaches to kbi part no. ii39700 / zb .confirm to rdso spec. no. rdso / 2011 / cg 04, rev 1 & amndt. 1. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 25.00 numbers , brake caliper unit leverage ratio 2.48 without brake cylinder for lhb fiat bogie power cars to kbi part no. ii39601 / za .confirming to rdso spec. no. rdso / 2011 / cg 04, rev 1 & amndt. 1. [ warranty period: 30 months after the date of delivery ] , led plate kbi part no.c133700 as per rdso spec. no. rdso / 2011 / cg 04 rev.01. [ warranty period: 30 months after the date of delivery ] , over hauling kit for brake cylinder kbi make [ 1117429 / 1204 v or 1182516 / 1204 lp ] consisting of 27 item as per annexure a [ knorr bremse india pvt ltd ] kbi part no 1 ] b 24037 o ring =1 , 2 ] b 25145 / 21 shaft sealing ring =1 , 3 ] b 25145 / 25 shaft sealing ring =1, 4 ] b 25145 / 26 shaft sealing ring =1, 5 ] b 26669 spring washer p =7, 6 ] b 30779 o ring =1, 7 ] b 33687 / 14 o ring =1, 8 ] b 33793 / 2 hose clamp =1, 9 ] b 33793 / 6 hose clamp =1 , 10 ] b33793 / 8 hose clamp =1, 11 ] b 53267 / a washer =1, 12 ] b 65557 / 4 machine screw =1, 13 ] b75404 protective cap=1, 14 ] b 85886 / 5 hex head bolt =1, 15 ] c 57231 / 1 supporting roller =2, 16 ] 464360 retaining ring =2, 17 ] 462767 snap ring ==2, 18 ] 463250 clamping pin =1, 19 ] 465121 lock washer =1, 20 ] b 38079 collar =1, 21 ] 466250 clamping pin =1, 22 ] b 23166 thrust bearing needle=1, 23 ] b 66529 / 5 breather plug =1, 24 ] b 43640 washer=1, 25 ] b 65580 / 12 bellow =1, 26 ] 466885 locking ring =13, 27 466887 locking ring =3 specn: rdso spec. no. rdso / cg04 rev.01. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 20.00 set ajmer , nwr , overhauling kit for distributor valve with rlv lhb coaches consisting 31 items make knorr bremse as per annuxure a atteched. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 180.00 set , pair of brake pad holder ( lh ) for brake caliper for lhb coaches as per m / s knorr bremse part no 176904 / a and brake pad holder ( rh ) for brake caliper for lhb coaches as per m / s knorr bremse part no. 176903 / a [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 22.00 numbers , brake cylinder with hand brake arrangement ( pbacm 254 130 ) for lhb coaches m / s. knorr bremse part no. ii 82516 / 1204 lp. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 6.00 numbers ajmer , nwr , rlv kit items for lhb dv consisting of 03 items of m / s knorr bremse 01. diaphragm a 49886 02 nos. 02. control sleeve b 25804 01 no 03. o ring 463074 01 no. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 240.00 set ajmer , nwr , brake cylinder left verson for lhb coaches to kbi part no. i70297 / 704ur and drg. no. c160859 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 13.00 numbers ajmer , nwr , emergency brake accelerator eb3 s / l without bracket kbi part no 189179. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 14.00 numbers , brake cylinder right version for lhbcoach to kbi part no. ii82515 / 304lp and drg. no. c177349 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 11.00 numbers ajmer , nwr , overhaul kit for emergency brake accelerator for lhb coaches to kbi part no.189179 consisting of 21 items list as per given below: s.no. description part no. qty / kit 1. retaining ring 464845 01 no. 2. grooved ring a18294 / 5 02 no. 3. valve tappet a 30530 01 no. 4. cup diaphragm a30711 01 no. 5. cup diaphragm a38362 01 no. 6. gasket a38363 01 no. 7. strainer a38433 / 1 01 no. 8. o ring a40125 / 14 02 no. 9. o ring a54062 04 no. 10. toothed ring a86235 / 1 01 no. 11. retaining ring a86239 01 no. 12. o ring a91453 01 no. 13 o ring b21836 01 no. 14. o ring b35265 01 no. 15. valve sealing ring b58852 / 6 01 no. 16. valve sealing ring b62784 / 3 01 no. 17. valve sealing ring b63323 / 2 01 no. 18. knorr k ring 459356 01 no. 19. knorr k ring 462581 01 no. 20. knorr k ring 465924 01 no. 21. diaphragm b82200 01 no. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 240.00 set ajmer , nwr , overhauling kit for brake cylinder to kbi part no. 170191 / 704w and 170191 / 304w ( earlier design ) and 1182515 / 704 lp and 1182515 / 304 lp ( current design ) for lhb coaches cons isting of 20 items ( 1 ) shaft sealing ring part no. b25145 / 21 qty. 01 nos. ( 2 ) spring washer part no. b26669 qty 07 nos. ( 3 ) o ring part no. b30779 qty.01 nos. ( 4 ) hose clamp part no. b33793 / 2 qty. 01 nos. ( 5 ) hose clamp part no. b33793 / 6 qty. 01 ( 6 ) hose clamp b33793 / 8 qty. 01 nos. ( 7 ) washer b53267 / a qty. 01 nos. ( 8 ) fastening wire part no. b61190 / 4 qty. 01 nos. ( 9 ) machine screw part no. b65557|4 qty. 01 nos. ( 10 ) protective cap part no. b75404 qty. 01 nos. ( 11 ) snap ring part no. 462767 qty. 02 nos. ( 12 ) clamping pin part no. 463250 qty. 01 nos. ( 13 ) lock washer part no. 465121 qty. 01 nos ( 14 ) colar part no. b38079 qty. 01 nos. ( 15 ) locking ring part no. 466031 qty. 01 nos ( 16 ) clamping pin part no. 466250 qty. 01 nos. ( 17 ) thurstin bearing needle part no. b23166466 qty. 01 nos. 18 ) breather plug part no. b66529 / 5 qty. 01 nos. ( 19 ) washer part no. b43640 qty. 01 nos. ( 20 ) bellow part no. b65580 / 12 qty. 01 nos. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 200.00 set ajmer , nwr , overhauling kit for cock dh7 for lhb coaches to kbi part no. 188738 consisting of 06 items. ( 1 ) retaining ring. 457709 qty 1 no. ( 2 ) knorr k ring. 462575 qty 2 nos. ( 3 ) o ring, a47412 qty 1 no. ( 4 ) o ring, a95468 qty 1 no. ( 5 ) o ring, k 4140 qty 3 nos. ( 6 ) valve seat bushing, c 170298, qty1 no special terms & conditions: guarantee / warranty 36 months from the date of delivery or 24 months from the date of placing in service whichever is earlier [ warranty period: 30 months after the date of delivery ] page 5 of 11 run date / time: 08 / 02 / 2023 16:15:58stores / north western rly tender document , over hauling kit for cock ahb to kbi parts no wbahb230aa002 for air brake system of lhb coachess consisting of 09 items. ( 1 ) gasket part no. wb419137a qtyiset. 02 nos ( 2 ) springpart no. wb409906 qty / set. 01 no. ( 3 ) shaft sealing ring part no. w4082704a qty / set. 01 no. ( 4 ) oring part no.or022000 qty / set. 02 nos. ( 5 ) 0 ring part n0. b76832 qty / set. 01 no. ( 6 ) 0 ring partno a78503 qty / set. 01 no. ( 7 ) o ring part no oro10000 qty / set. 01no. ( 8 ) 0 ring part no b72767qty / set. o3 nos. ( 9 ) 0 ring part no or123000 qty / set. 01 no [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 480.00 set ajmer , nwr , overhauling kit for filter to kbi part no. wbfil100aa002 for air brake system of lhb coaches consisting of 03 items. ( 1 ) o ring part no. b76832 qty / set 01 no. ( 2 ) o ring part no.b72767 qty. / set 02 nos. ( 3 ) retaining ring part no. 468861 qty. / set 01 no. special terms &conditions: guarantee / warranty 36 months from the date of delivery or 24 months from the date of delivery or 24 months from the date of placing in service whichever is earlier [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 301.00 set , cock dh 7te lhb knorr bremse part no. 188738 drg.no. b 80866 kb [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 25.00 numbers , overhauling kit for indicator to kbi part no. 148102 / w for lhb coaches consisting of 02 items. ( 1 ) plastic cover part no. c107249 qty / set 01 nos. ( 2 ) k. ring part no. 457353 qty / set 01 nos. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 408.00 set ajmer , nwr , cock ahb 200 nw 19 ( lhb ) rcf drg no.wb.415503 za & kbi part no. wbahb230aa002 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 23.00 numbers ajmer , nwr , kit for emergency brake valve nb12 kbi part no. 194023 / ki consisting 8 items, ( 1 ) o ring a27763 / 22=1no ( 2 ) o ring a93706=1no ( 3 ) o ring b90075=1no ( 4 ) knorr k ring 461627=1no ( 5 ) knorr k ring 461794=1no ( 6 ) hexagon nut 468825=1no ( 7 ) retaining ring 463775=1no ( 8 ) locking ring 466031=4no. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 60.00 set ajmer , nwr , dump valve connector kbi part no n.62148 / 10000 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 48.00 numbers , set of connector kbi part no. stn 30979 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 4.00 set , test connection k 1e knorr bremse part no. 179470 / 07k [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 9.00 numbers , poh kit for kbi make emergency brake cable box for lhb coaches consisting 7 items. ( 1 ) kbi part no. b73364 / 3. description valve head qty / set 01 ( 2 ) kbi part no. 455588. description lock washer qty / set 01 ( 3 ) kbi part no. 456790. description clamping pin, qty / set 01 ( 4 ) kbi part no. 459143. description clamping pin, qty / set02 ( 5 ) kbi part no. 461043. description lock washer, qty / set 01 ( 6 ) kbi part no. 461664. description toothed washer, qty / set 02 ( 7 ) kbi part no. 465632. description spring, qty / set 01 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 35.00 set ajmer , nwr , kit for brake caliper without brake cylider consisting 19 items ( 1 ) bush kbi part no. c101877 qty 02 set, ( 2 ) washer kbi part no. b58532 / 9 qty 2 set, ( 3 ) bush kbi part no. c101892 / 2 qty 02 set, ( 4 ) bush kbi part no. c80809 / 13 qty 02 set, ( 5 ) flanged bush kbi part no. c81080 / 14 qty 04 set, ( 6 ) hexagon nut kbi part no. 469548 qty 02 set ( 7 ) hose clamp kbi part no. b33793 / 20 qty 02 set ( 8 ) clamp ring kbi part no. c146738 / 4 qty 02 set ( 9 ) apron kbi part no. c112059 / 4 qty 02 set ( 10 ) threaded rod kbi part no. c58819 qty 04 set ( 11 ) hexagon nut kbi part no. c20308 / 13 qty 04 set ( 12 ) washer kbi part no. c84536 / 25 qty 04 set ( 13 ) pin kbi part no. c22894 / 2 qty 02 set ( 14 ) locking gate kbi part no. c77932 qty 02 set ( 15 ) locking spring c66859 qty 02 set ( 16 ) pivot screw kbi part no. c51515 / 01 qty 04 set ( 17 ) locking ring kbi part no. 466572 qty 04 set ( 18 ) clamping pin kbi part no. 462523 qty 02 set ( 19 ) bush kbi part no. b33096 / 03212 qty 08 set [ warranty period: 30 months after the date of delivery ] page 7 of 11 run date / time: 08 / 02 / 2023 16:15:58stores / north western rly tender document...

Dr. S.N.Medical College - Rajasthan

35907818 tender for printing and stationary of items printing and stationary for 2 years , stationary and printing , ecg paper sheet 9108 bpl , file cover10”x14”with printing280 gsm with less , craft paper envelope star craft with printing [ 14.5” x 17.5” ( 100 gsm ) star craft ] , craft paper envelope star craft with printing [ 14.5” x 17.5” 100 gsm normal craft ] , craft paper envelope star craft with printing [ 12.5” x 15.5” 100 gsm normal craft ] , craft paper envelope star craft with printing [ 10.5” x 12.5” 100 gsm normal craft ] , craft paper envelope star craft with printing [ 11”x 5” 100 gsm ] , craft paper envelope star craft with printing [ 9” x 4” 100 gsm ] , craft paper envelope star craft with printing [ 8.5” x 10.5”100 gsm normal craft ] , craft paper envelope star craft with printing [ 4.5” x 4.5” 100 gsm normal craft ] , craft paper envelope star craft with printing [ 11” x 14” x ray envelop 100 gsm ] , file cover with printing & lases ( superior quality 9 / 924 ) , stamp pad 110 mm x 70 mm , stamp pad 160mm x 97 mm , stapler pins no. 10 , stapler pins no. 24 / 6 , gum bottle 150ml , gum bottle300ml , ball pen , file tag – 8” ( 800 tag per bundle ) , permanent marker pen , cd marker pen , t pin weight 70 gsm 100gm per pkt. , index file , correction pen 9 ml , high lighter pen set. , pin cushion plastic , box file , glue stic 15gm kores / fevistic / scotch or other brand , water proof bag for cycle sewer , plastic scale 12” , calculator 12 digit , file pad , file flap , celling wex , cloth coated envelop 16”x12” , punching machine ( specification: punching capacity 290 pages / sheets; punching distance: 70 / 80 mm; punching dia: 6.00 mm ) , heavy duty stapler ( specification: staple use 23 / 6 ~ 23 / 24, loading capacity: 100 staples, stapling capacity: 210 sheets ) , i card with cover & lace ( sample required ) * , certificates frame , stamp pad small , stamp pad big , stamp ( seal ) , pencil sharpener , computer paper a4 size 75 gsm for laser printer , computer paper a4 size 75 gsm for laser printer numbering & printing , compute paper fs size 75 gsm for laser printer , computer paper 70 gsm for dot matriks printer ( 8 x 10 / 2 ) with printing and numbring , pen drive ( 16 / gb ) , toner repairing ( magnetic rollers ) , hp laser printer cartridge 1536 mfp , hp laser printer cartridge 1566 ( hp – 78a ) , hp laser printer cartridge 1020+ ( hp – 12a ) , hp laser printer cartridge p1007 , hp laser printer cartridge p1008 , hp laser printer cartridge p1106 ( hp – 88a ) , samsung laser printer cartridge xpress m2091 , cannon cartridge for laser jet lbp 2900b ( cannon – 303 ) , cannon cartridge for model m241d , dmp printer cartridge ( epson fx 890 ) ( model no. s015329 ) ( original epson ) , dvd r , cdbag 40 cd , led monitor 17 inch , lan connectors ( rj – 45 ) , desmate label stickers for dot matrix printer ( 100 mm x 48mm ) , external hard disk for data backup 2tb , kyocera m2040dn printer toner ink powder 250gm pkt , konika milonta printer b12hub165e tonner bottle , cartidge for hp never stop laser mfp 1200a ( cartidge no 104a ) , pad binding ( 100 papers pad ) 18x22 / 8 , pad binding ( 300 papers pad ) 16x26 / 2 , pad binding ( 300 papers pad ) 16x26 / 4 , pad binding ( 300 papers pad ) 16x26 / 8 , pad binding ( 300 papers pad ) 18x22 / 2 , pad binding ( 300 papers pad ) 18x22 / 4 , pad binding ( 300 papers pad ) 18x22 / 8 , service book / gpf si pass book binding , letter pad for blood bank 70 gsm paper 18” x 22” / 6 , blood doners certificate in multi colour on glassed card sheet 7.5” x 9.5” , certificates in multi colour on glassed card sheet size 7.5” x 9.5” for 26 january, 15 august ( sample required ) * , white paper rim 17 x 2770 gsm , type paper 70 gsm , carbon paper blue full scape size , carbon paper big size , file cover with printing & lases ( superior quality 9 / 924 ) , special file cover with printing & lases ( 18.1 kg card sheet ) 7” x 9½” , stamp pad ink 50 ml , stamp pad 110 mm x 70 mm , stamp pad 160mm x 97 mm , stapler small 10 , stapler big size no. 24 / 6 , stapler pins no. 10 , stapler pins no. 24 / 6 , glass marking pencil , botekin wooden handle , gum bottle 150ml , gum bottle300ml , gum bottle 700 ml , pencil ( h. b. ) , ball pen , refill for ball pen , paper weight glass , paper weight plastic , file tag – 8” ( 800 tag per bundle ) , permanent marker pen , cd marker pen , t pin weight 70 gsm 100gm per pkt. , index file , file ledger , file lase no. 924 , plastic tap transparent 50 mt.1” , plastic tap dispenser , gel pen – blue / green / black / red , plastic jug with1½ ltr. capacity , tumbler glass , trey , correction pen 9 ml , high lighter pen set. , page marker slip ( 80x3 ) , pin cushion plastic , clip pin pkt. office clip 30 , box file , glue stic 15gm kores / fevistic / scotch or other brand , water proof bug for cycle sewer , plastic scale 12” , calculator 12 digit , file pad , dak pad plastic , file flap , celling wex , cloth coated envelop 16”x12” , cloth coated envelop 11”x 5” , punching machine size small / big , register ( 100 pages ) , punching machine ( specification: punching capacity 290 pages / sheets; punching distance: 70 / 80 mm; punching dia: 6.00 mm ) , heavy duty stapler ( specification: staple use 23 / 6 ~ 23 / 24, loading capacity: 100 staples, stapling capacity: 210 sheets ) , sticker for admission ticket size: ……………… ( 2x4 inch ) , two vehicle sticker , four vehicle sticker , sticker of blood bank bag in four colour ( 4½ x 3½ ) , i card with cover & lace ( sample required ) * , carbon paper a4 size , certificates frame , p.a. diary , slip pad ( 500 sheet ) , raw peg page 250 , stamp pad small , stamp pad big , stamp ( seal ) , aerylic sheet a4 size – rate per inch , plastic bag bottom folder single pocket , plastic bag bottom folder double pocket , pencileraser non dust , pencil sharpener , dak folder cloth coated ( 38cm x28cm ) , short hand note book 100 page 70 gsm , binder clip 32 mm solo , glossy paper a4 size. inkjet paper tmt reporting paper. , computer paper a4 size 75 gsm for laser printer , computer paper a4 size 75 gsm for laser printer numbering & printing , compute paper fs size 75 gsm for laser printer , computer paper 70 gsm for dot matriks printer ( 8”x 6” / 2 ) , computer paper 70 gsm for dot matriks printer ( 8”x 6” / 3 with number ) , computer paper 70 gsm for dot matriks printer ( 8 x 10 / 1 ) , computer paper 70 gsm for dot matriks printer ( 10 x 12 / 1 ) , computer paper 70 gsm for dot matriks printer ( 10 x 12 / 2 ) , computer paper 70 gsm for dot matriks printer ( 15” x 12” / 1 ) , computer paper 70 gsm for dot matriks printer ( 15” x 12” / 3 ) , pen drive ( 16 / 32 gb ) , computer re writable disk with cover ( cd rw ) , computer compact disk with cover ( cd r ) , toner refilling , toner repairing ( drum ) , toner repairing ( pcr ) , toner repairing ( doctor / wiper blade ) , toner repairing ( magnetic rollers ) , printer repairing ( teflon fuser film sleeve ) , hp laser printer cartridge 1536 mfp , hp laser printer cartridge 1566 ( hp – 78a ) , hp laser printer cartridge 1020+ ( hp – 12a ) , hp laser printer cartridge p1007 , hp laser printer cartridge p1008 , hp laser printer cartridge p1106 ( hp – 88a ) , hp laser printer cartridge pro m403d , samsung laser printer cartridge xpress m2091 , brother laser printer cartridge dcp –l2520d , cannon cartridge for laser jet lbp 2900b ( cannon – 303 ) , cannon cartridge for model m241d , dmp printer cartridge ( epson fx 890 ) ( model no. s015329 ) ( original epson ) , printer ribbion for epson fx890 , cd r , dvd r , cdbag 40 cd , usb mouse optical wired , usb keyboard computer wired , tvs gold usb wired keyboard , led monitor 17 inch , led / monitor19 inch , photo frame 12*10 ( steel ) , 5 port lan switch , 8 port lan switch , 16 port lan switch , cat 6 lan cable box ( 305mtr ) , lan connectors ( rj – 45 ) , rj 45 cat 6 lan i / o box set ( with i / o box, faceplate and i / o keystone jack ) , desmate label stickers for dot matrix printer ( 100 mm x 48mm ) , computer c mos bios battery , crimping tool lan cutter with cable cutter , punch down tool , lan tester , screwdriver kit , pliers , tweezers pack of 4 , external hard disk for data backup 2tb...

Rajasthan Police Academy - Rajasthan

35691581 supply of electrical material halogen light, plug, screw, casing sheet, pipe, pipe band, gang box, sodium light, ignator, pole box iron / pvc, nut bolt, fan box, ms saddle, fitting surface laser charge, exhaust fan, greas, led light, wire bundle, cable submersible, cable copper, three phase aluminum cable, ht cable box, changeover switch, track light, etc....

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

35679929 supply and installation lab equipments in vocational labs in govt. schools of district karauli , electronics& hardware lab tools , screw driver set , combination pliers , diagonal cuttin pliers , long nose pliers , hand drill , electric drill upto 10mm , hacksaw , wire stripper , soldering iron (10w/25w) , adjustable wrench , ball pein hammer , line tester , double ended spanner set , instrument files , chisels set , vice , vice , tweezer , pcb drill , pincer , magnifying glass , hammer , de soldering pump , 1 desktop computer , multi meter , mixer, juicer & grinder , radiation leakage tester , lcd tds meter , microwave oven , printer with scanner , water purifier , gloves , safety helmet , safety shoes , fire extinguisher , oscilloscope , rubber matt , electronics & hardware lab consumables (recurring items list) , resistors , capacitors , coiis (aluminium) , transistors , ic / ic sockets , led , transformers , ribbon cable , upt cat.5 cables (box) , upt cat. 3 cables (box) , connecting lead , sockest , jacks & plugs (each set) , connecting plugs , drill bits , soldering iron bit , soldering ironelements/wax /wire , silicon paste , machine oil , swithces (each set) , screws & nuts (as per need) , fuses , brushes , wire brushes , frist aid kit , power transistor bases , insulating tape , rj 45 , steel ruler , ruler , safety googles , anti static wrist , crimping tools , t square , display charts & learning manuals , learning , work instructions , hand outs , schematic diagrams , charts , block diagrams , layout plans , location plans , instrumentation diagrams , loop diagrams , system control diagrams...

Jawahar Kala Kendra - Rajasthan

35055295 reg supply of audio stage equipment and accessories stage snaker cable box, mic cable, di box, battery, audio cable, condensor instrument clip in mic, vocal mic, electric board, multimedia speaker, battery for laptop, usb audio interface, wireless presenter remote control with laser remote logitec, mic stand clamp, external stero sound adaptor....

North Western Railway - Rajasthan

34799921 supply of poh kit for kbi make emergency brake cable box.poh kit for kbi make emergency brake cable box., poh kit for kbi make emergency brake cable box for lhb coaches consisting 7 items. ( 1 ) kbi part no.b73364 / 3. valve head qty. / set 01 ( 2 ) kbi part no.455588.lock washer qty / set 01 ( 3 ) kbi part no.456790. clamping pin, qty / set 01 ( 4 ) kbi part no.459143. clamping pin, qty / set 02 ( 5 ) kbi part no.461043. lock washer, qty / set 01 ( 6 ) kbi part no.461664. toothed washer, qty / set 02 ( 7 ) kbi part no.465632. spring, qty / set 01 carriage stores depot rajasthan 54.00 set ajmer , nwr...

RAJASTHAN COUNCIL OF SCHOOL EDUCATION - Rajasthan

34617334 supply and installation of lab equipment government school located at karauli district. electronics and hardware karauli , electronics& hardware lab tools , screw driver set , combination pliers , diagonal cuttin pliers , long nose pliers , hand drill , electric drill upto 10mm , hacksaw , wire stripper , soldering iron (10w/25w) , adjustable wrench , ball pein hammer , line tester , double ended spanner set , instrument files , chisels set , vice , vice , tweezer , pcb drill , pincer , magnifying glass , hammer , de soldering pump , 1 desktop computer , multi meter , mixer, juicer & grinder , radiation leakage tester , lcd tds meter , microwave oven , printer with scanner , water purifier , gloves , safety helmet , safety shoes , fire extinguisher , oscilloscope , rubber matt , electronics & hardware lab consumables (recurring items list) , resistors , capacitors , coiis (aluminium) , transistors , ic / ic sockets , led , transformers , ribbon cable , upt cat.5 cables (box) , upt cat. 3 cables (box) , connecting lead , sockest , jacks & plugs (each set) , connecting plugs , drill bits , soldering iron bit , soldering ironelements/wax /wire , silicon paste , machine oil , swithces (each set) , screws & nuts (as per need) , fuses , brushes , wire brushes , frist aid kit , power transistor bases , insulating tape , rj 45 , steel ruler , ruler , safety googles , anti static wrist , crimping tools , t square , display charts & learning manuals , learning , work instructions , hand outs , schematic diagrams , charts , block diagrams , layout plans , location plans , instrumentation diagrams , loop diagrams , system control diagrams...

Department of Information Technology and Communication - Rajasthan

33538296 rate contract rfp for stationary, computer media, consumable and other office itmes 1 canon toner 320 2 canon toner 328 3 canon toner 337 4 canon toner 324 5 toner hp 6511a 6 toner hp ce 278a 7 toner hp cc388a 8 toner hp 05a 9 toner hp 230a 10 toner hp 287a 11 toner hp cf280a, 1 canon toner 328 2 canon toner 337 3 canon toner 324 4 toner hp 6511a 5 toner hp ce 278a 6 toner hp cc388a 7 toner hp 05a 8 toner hp 230a 9 toner hp 287a 10 toner hp cf280a, ( a ) cd / dvd 1 dvd r with cover ( frontech / samsung / moserbaer / hp / sony ) ( b ) usb pen drive ( 3.1 and above ) 1 32 gb ( kingston / sandisk / hp / moserbaer / transcend ) 2 64 gb ( kingston / sandisk / hp / moserbaer / transcend ) 3 128 gb ( kingston / sandisk / hp / moserbaer / transcend ) ( c ) external hard disk drive 1 1 tb sata usb powered ( seagate / wd / transcend ) 2 2 tb sata usb powered ( seagate / wd / transcend ) 3 4 tb usb powered ( seagate / dell / sony / wd / transcend ) 4 512 gb ssd usb powered ( seagate / wd / aarvex ) 5 1 tb ssd usb powered ( seagate / wd / aarvex ) 6 2 tb ssd usb powered ( seagate / wd / aarvex ) d internal hard disk drive 1 512 gb sata hdd 7200 rpm, ( seagate / wd / transcend / aaevex ) 2 1 tb sata hdd 7200 rpm ( seagate / wd / transcend / aaevex ) 3 512 gb ssd ( seagate / wd / transcend / aaevex ) 4 1 tb ssd ( seagate / wd / transcend / aaevex ) 5 512 gb ssd nvme, m.2 port ( seagate / wd / transcend / aaevex ) 6 1 tb ssd nvme, m.2 port ( seagate / wd / transcend / aaevex ) ( e ) ram 1 desktop ram ddr4 ( 8 gb ) ( hynix / samsung / transcend / kingston ) 2 laptop ram ddr4 ( 8 gb ) ( hynix / samsung / transcend / kingston ) 3 desktop ram ddr3 ( 8 gb ) ( hynix / samsung / transcend / kingston ) 4 laptop ram ddr3 ( 8 gb ) ( hynix / samsung / transcend / kingston ) ( f ) other items 1 usb optical mouse ( logitech / iball / hp / dell ) 2 optical wireless mouse ( logitech / iball / hp / dell ) 3 usb keyboard ( logitech / iball / hp / dell ) 4 wireless keyboard ( logitech / iball / hp / dell ) 5 wireless keyboard & mouse combo ( logitech / iball / hp / dell ) 6 web camera ( logitech / iball ) ( minimum hd 720p 30fps 1280*720 resolution ) 7 vga cable standard size 1.5 meter 8 hdmi cable 1.5 meter 9 speaker set ( 2 nos. ) with usb power, 1.2 watt, 3.5 mm input 10 mechanical keyboard ( tvs gold ) , 1. all pin ( 26 mm, nw 70 gram ) 2. binder clip : a. 19 mm b. 25 mm c. 32 mm d. 41 mm 3. gem clip / u pin ( plastic cover ) 4. poker ( wooden handle ) 5. poker ( iron base ) 6. transparent adhesive tape ( scotch / cello / wonder ) , 7. brown packing tape ( scotch / cello / wonder ) a. 1, 55 meter b. 2, 55 meter 8. both side tape ( scotch / cello / 3m ) a. 1 wide both side tape thick b. 1 wide both side tape thin 9. cleaner ( colin / cleen ) ( 500 ml ) 10. gum ( camlin / kores ) a. 700 ml b. 150 ml 11. glue stick 15 gm ( kores / scotch / fevi stick ) 12. large paper cutter ( natraj or equivalent brand ) 13. hb pencil ( camlin / natraj / faber castel ) 14. non dust eraser ( camlin / natraj / faber castel ) 15. sharpener ( camlin / natraj / faber castel ) 16. scale plastic ( 12 ) ( natraj / camlin ) 17. scale iron ( 12” ) ( ajanta / camlin / natraj ) 18. stamp pad 110mm x 70mm ( ashoka ) 19. punching machine ( kangaroo or equivalent brand ) a. 14 page punching capacity ( dp 480 ) b. 22 page punching capacity ( dp 680 ) c. 60 page punching capacity ( dp 800 ) d. 1 hole punching no. 10 20. stapler ( kangaroo / max ) a. staples use :no. 10, stapling capacity upto 15 pages, loading capacity:50 staples b. staples no. 24 / 6, 26 / 6, stapling capacity upto 30 pages, loading capacity:50 staples ( 24 / 6 ) , 100 staples ( 26 / 6 ) ( kangroo hp 45 equivalent ) c. staples no. 24 / 6, 26 / 6, stapling capacity upto 30 pages, loading capacity:50 staples ( 24 / 6 ) , 100 staples ( 26 / 6 ) ( kangroo hdz 45 equivalent ) 21. stapler pin ( kangaroo / max ) a. no. 10 1m ( 20x50=1000 staples ) b. no. 24 / 6 ( 20x50=1000 staples ) c. no. 26 / 6 ( 20x50=1000 staples ) 22. envelop ( cloth ) a4 size with min. 100 gsm paper 23. envelop ( cloth ) fs size with min. 100 gsm paper 24. cd / dvd permanent marker ( camlin / faber castel / luxor ) 25. paint marker ( golden color ) ( camlin / faber castel / luxor ) 26. white board marker ( camlin / luxor / faber castel / kores ) 27. correction fluid ( camlin / luxor / faber castel / kores / kangaro ) 28. peon book 100 sheets 29. slip pad 140mm x 225mm, 70 gsm inner paper with line, 1 mm card sheet on back, 30. spiral slip pad a. 140mm x 225mm, 70 gsm, multi color inner paper with line, card sheet on back and plastic cover 80 sheets ( 160 pages ) b. 140mm x 225mm, 70 gsm, inner paper with line, card sheet on back and front 80 sheets ( 160 pages ) 31. white board duster 32. white board duster ( magnate ) 33. a4 size photo paper 180 gsm ( 50 sheets per pkt ) ( desmat / novajet / epson / kodak ) 34. 75 gsm paper a4 size ( 500 sheets per ream ) ( jk / modi / xerox / tnpl ) 35. 75 gsm paper fs size ( 500 sheets per ream ) ( jk / modi / xerox / tnpl ) 36. 75 gsm a3 size ( 500 sheets per ream ) ( jk / modi / xerox / tnpl ) 37. 75 gsm green pie paper fs size ( 500 sheets per ream ) ( jk / modi / xerox / tnpl ) 38. address label ( for laser printer a 4 size ) 100 sheet in a packet ( desmat or equivalent ) a. 16 label per page b. 24 label per page 39. basta ( cloth ) size 90*90 40. file pad – weight 32 ons, size 10*15, 36 ( dori 4*27 flap ) 41. file cover ( 31 kg cpm board ) with printing of deptt name 42. file lace best quality ( 100 nos. of laces in one bunch ) 43. file tag best quality ( 50 nos. of laces in one bunch ) 44. transparent l shape folder ( plastic ) ( solo / trio ) 45. ring binder, 1, 2 d, pvc folder a4 size, holds upto 250 sheets ( solo / trio or equivalent ) 46. index file ( box file ) 47. pen a. reynolds 0.45 b. cello fine grip c. flair writo meter d. flair ball pen e. uniball eye fine f. parker roller pen ( beta premium i. parker vector standard j. uniball gel impact k. uniball eye broad 48. duster ( cloth ) 2ft x 2ft. 49. post it ( 3m ) a. size 3” x 3” 100 sheets, 50. cell ( duracell ) a. pencil cell ( aa ) b. pencil cell ( aaa ) 51. pvc cards packet of 50 pvc cards ( 30 mil ) 52. dustbin plastic min 12 litr. ( poly propylene plastic ) without cover 53. dustbin min. 12 litr ( poly propylene plastic ) with cover 54. dustbin 15 ltr ( poly propylene plastic ) with cover 55. water jug plastic ( 2 ltr. or more ) ( poly propylene plastic ) – ( cello / prestige / orient / milton or equivalent ) 56. extension board ( make: belkin ) a. 4 socket b. 6 socket c. 8 socket 57. scissors ( kangaro munix ) stainless steel, 185 mm ( munix sl 1173 ) 58. electric kettle ( prestige, borosil ) , 1.5 litre 59. tea flask tuff insulated jug 1 litres ( cello / milton ) 60. best quality white window envelop ( 50 piece ) 11 x 5 80 gsm 61. towel 100% cotton, 75 cm x 150 cm ( bombay dyeing ) 62. refillable self inking stamp seal two line 63. refillable self inking stamp seal three line 64. refillable self inking stamp seal four line 65. refillable self inking stamp seal five line 66. refillable self inking stamp seal big size ( more than 5 line ) , 1. 9 u rack with pdu & cooling fan 2. installation charges for 9 u rack 3. i / o port set ( network keystone jack, gang box, face plate ( dlink / digisol / dax / amp / molex ) 4. cat 6 network cable box 305 mtr. ( d link / digisol / dax / amp / molex ) 5. laying of cat 6 cable 6. isi mark pvc casing 1 inch 7. laying of pvc casing 8. 5 port switch 10 / 100 / 1000 mbps ( dlink / digisol / digilink ) 9. 8 port switch 10 / 100 / 1000 mbps ( dlink / digisol / digilink ) 10. rj 45 connector ( dlink / digisol / digilink / molex ) ....

Department of Higher Education - Rajasthan

33459287 bids are invited for utp cat6 cable box 305 meter , l 2 gigabit switch with 2 sfp manageable 24 port poe , cat6 single face plate io with surface mount box , 12u wall mount rack with pdu and fan , cable manager cat 6 for network rack , cat 6 utp patch cord 1 meter , cat 6 utp patch cord 2 meter , 24 port patch panel cat 6 loaded with utp io , offline ups 1kva , cat 6 cable laying with conduit and required accessoriesincluding testing , labeling , io termination and fixing ,rack fixing, installations and dressing including fixinghardware , patch panel termination and activation withmounting hardware , switch installations with mountinghardware , ups installations , 3 years onsite comprehensivewarranty and support total quantity : 11495...

Jodhpur Development Authority - Rajasthan

33033571 various electrical instruments installation work at barkatullah khan stadium sitcofwall/freestandingfloormounteddustandverminproof compartmentalisedcubical panel as per pwd specification for electrical works, made out of crca sheet . other parameters required as per point (a) ,(b), (c),(d) below: (a)thicknessofsheetshall notbelessthan1.6mmupto600mm length / widthof any compartment and be of 2.0 mm above 600 mm. loadbearingstructureshallbe of2.0mm thicksheetsupportedby base m.s. channel if required . side walls and cable alley compartments havingboltedtypedoorswith/without detachableextensiontype structure(b)panelshallbe dulytreatedforderustingin7tankprocesswith dephosphatingandwithpowdercoatingofminimum70micronson bothsideofpanelindesiredshade thepanelhavingpu/neoprene rubbergasketofnotlessthan3mmthickness,requiredhardware, separate detachable gland plate m.s. base channel (min75mm) , hinged door with locking arrangement for equipment/switchgear [c) interconnectionbetweenbusbarandswitchgears/cableshallbe rigidlysupportedandmadeoutbyflexiblecopperwires(upto125 amp ) and by solid bus bar(>125 amp ) . all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of busbarbusbarisinsulatedbyheatshrinkablesleeves.earthand neutral bus bar shall be half of the size of phase bus bar. (d)onlyouterareaonallsidesshallbemeasured&paneltobe fabricated only from cpri approvedfabricator. all as per drawing pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 2 providing & fixing of ip 51 multi functionmeter as per pwd specification for electrical works, isi marked (is 16444)/ confirming to iec61557&iec62052withlcd/led3/4 linedisplaycapableof measuring electricalparameterslikev,i,f,pf,kw,kva,kvar,kwh, kvah,kvarhdisplaywith1a/5actinputforlv/hvnetwork,with /without rs 485 communication port etc.oem must have bis certificateand & shallhavesubmit nabl/cpri/erda labtest reports beforeexecution&completeinallrespect.allasperpre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . multifunction lcd meter with v,a,f,pf,kw,kva, old energy memory, class 1 accuracy without rs485 port . 3 supplyingandfixingofaluminium(iec60105iso209 1,2)/copper (iec60028)busbarasperpwdspecificationfor electricalworks, by means of smc / dmc type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . electrolytic grade aluminium bus bar 6010 grade 4 providing& fixingof bisapprovedcurrenttransformerasper pwd specificationforelectricalworks,isimarkedasper is2705 1992/ conformingtoiec60044 1,withsecondaryterminal ofctshallbe brought out suitable to a terminal block which shall be easier accessiblefortestingandterminalconnection,withallnecessary support in existing panel including connection etc. as requiredcurrent transformer resin cast wound primary / ring type tape wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu crosssectionofsecondarywire1.5sqmm(minimum),includingall necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr .400/5 to 1200/5, burden 15 va 5 providing& coveringof existing cablelying in existingtrenchbyiindclassbricks/stoneslabof minimum 32mm thick and 250 mm widein complete running lengthof trenchcomplete as required. 6 labourchargesforexcavationof30cmx75cmsize trenchinloosesoilincludingrefillingofexcavated earth,compactionofearth,makinggoodthesame complete as required . 7 providing&layingp.v.c./xlpeinsulated&p.v.c. sheathed un armoured / armouredaluminiumcable of 1.1 kv grade as per pwd specification for electrical works inexistingrcc/hume/stoneware/pvc pipe/ open duct/cable trench with filling of excavated earth in trench, on existing cable trays or on surface etc. includingmakingnecessaryconnection,testing etc. as required of size andas per points (a), (b), (c), mentioned below: (a)material: h4 grade aluminiumconductorof purity >99.6 %& as peris:1554 p i / is :7098 p i(b)conductorshallhaveelectrolyticaluminium confirming to is 8130, is 3975 1999for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures .(c) oem must have iso 9001 &14001 certifications forqualityassuarance&itsowninhousenabllab setup for all testing facilities forcables . appropriate type test certificate / oem test report shall be submitted .all above as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr .armoured cable120.0 sq. mm 3.5 core 8 185.0 sq. mm 3.5 core 9 providing&layingxlpeinsulatedasperis:7098/ii/85 h.t.cableasperpwdspecificationforelectricalworks forworkingvoltage11k.v.(e)in existingrcc/hume/ stoneware/pvcpipe/openduct/cable trenchwith fillingofexcavatedearthintrench ,onexistingcable trays or on surface etc.including making necessary connection, testing etc. as required of size as per points (a), (b), (c) mentioned below: (a) material : h4 gradealuminium conductor of purity >99.6 %& as peris:1554 p i / is :7098 p i (b) conductor shall have electrolytic aluminium confirmingtois8130,is3975 1999 forarmouringof cables ,is 5831forsheath,is 10810(part 0to 64)for testing procedures (c)oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for alltestingfacilitiesfor cables. allaboveasperpre approved by engineer in charge.for additional technical parametersofproducts/work ,referannexurea attached with this bsr . 3 core 185.0 sq.mm 10 providing & laying of 25 cm thicklayer ofriver sand to cover ofexisting cablein 30 cm x 100/ 120 cm size cable trench with levellingand making symmetric 25 mm thick layer in complete running lengthof trenchas required. 11 providing &covering ofexistingcable lyinginexistingtrenchbyiindclassbricks/stoneslabofminimum 32mmthickand250mmwide incompleterunning lengthof trenchcomplete as required. 12 labour charges for excavation of 30cmx100cm size loose soil trench including refilling of excavated earth,compaction of earth, making good the same complete as required . 13 providing & making heat shrinkable typeindoor/outdoor/straightthroughterminations/jointkit as per pwd specification for electrical works suitable for 11 kv / 33 kv cable with required components, prepration ofcableends.typetestreport shouldbeas per is13573:2011 which covered all sequence for table 2 for termination kit and table 3 for streightthrough joint inclusivethermal&dynamicshortcircuittest,humidity test,soilfogtest.cross linkingshallbedoneoutside factorywithe beam/peroxidetechnology.extrusion process shall be in house oem within same vicinity. oem test lab should be as per iso 9001:2015 & 14001 : 2015 &reportssubmittedtoengineerin chargeincluding testing etc. as required of following sizes. all as per pre approved by engineer in charge.for additional technical parametersofproducts/work ,referannexurea attached with this bsr . 14 11 kv end termination kit outdoor type 3 core 240/300 sq.mm 15 11 kv end termination kit outdoor type 3 core 120/150/185 sq.mm 16 11 kv straight through joint kit 3 core 240/300 sq.mm 17 providing&layingp.v.c. /xlpeinsulated&p.v.c. sheathedun armoured/armouredcoppercableof 1.1kvgradeasperpwdspecificationforelectrical works inexistingrcc/hume/stoneware/pvc pipe/ open duct/cable trench with filling of excavated earth in trench, on existing cable trays or on surface etc. includingmakingnecessaryconnection,testing etc. as required of size andas per points (a), (b), (c), mentioned below: (a) copper conductor of electrlytic grade copper, purity>99.97%isimarkedasper is:1554p i/is:7098 p i, b)conductorshallmadeofcopperrodsconfirmingto is 613 1964,is 3975 1999for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures, (c) oem must have iso 9001 & 14001 certifications & its own in house nabl lab setup for all testing facilities forcables . appropriate type test certificate /oemtestreportshallbesubmitted.allaboveas per pre approved by engineer in charge.for additionaltechnicalparametersofproducts/work, refer annexure a attached with this bsr . armoured 1.5 sq.mm. 7 core 18 4.0 sq.mm. 4 core 19 providing&fixingof240/415vacmcbwithpositive isolationofbreakingcapacitynotlessthan10ka(b/c tripping characteristic as per type of load andsite requirement) 4kv impulse withstand voltage,as per pwd specification for electrical works with isi marked is 8828(1996) / conforming to iec 60898 1 2002, iec 60947 2, lowwattlosses,tripfreemechanisum,energylimiting of class 3 as per iec,minimum phase termination capacity of 35sq.mm.,conductorlineloadreversibility,labelholding facility,ip20contactprotectionandfittedwith existing distribution board/sheets, min. operation 20,000 upto 32 a rating and 10,000 upto 63 a, 5000 for 80 a ratingincluding makingconnections,testingetc.asrequired. .oemshall havesubmit nabl/cpri/erdaaccrediatedlabtest reports beforeexecution&allasperpreapprovedby engineer in charge.for additional technical parameters of products/work ,referannexureaattachedwiththis bsr. single pole mcb 6 a to 32 a rating 20 providing & laying of double wall corrugated pipe confirming to is : 14930 p 1 & 2with hdpe coupler at 1 mtr.depthbelowthegroundforlayingcableincluding making the trench and back filling , compaction of earth asrequired(excavationofearthtobepaidextraas required.) offollowingouterdia./innerdiaasper is:4984:1995.allasperpreapprovedbyengineerin charge.for additional technical parameters of products/work, refer annexure a attached with this bsr.55/50 mm 21 sitc of chemical gel earthing system of dual pipe technology made of with b classg i pipeas per is 1239 ( part 1):2004of medium duty of following sizesas per points mentioned (a), (b), [c), (d), (e) below : (a)filledwithanticorrosive conductive compoundswiththe permanentsealingsatboththeends,cpri/erda testedwith rms capacity of minimum 35 40 ka for withstanding 1 second(b)toensurethemoisturecontentandelectricalconductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound.thecompoundshallbetestedformnabl acredeated labfor lowresistivity ( less than 0.12 ohm meter) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987,ieee 80 2013 (clause 14.5d) , ieee 837 & ier 1956 with latest amendemnts©heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm.(d) testingofearthresistanceforvalueof5ohmsorless as required&mustrecordbyengineerinchargeduringsitevisit and ensure to enter in measurment book.(e) self certificate forconfirming abovestandards fromoem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . with pipe in pipe technology (outer pipe dia. / inner pipe dia. ) minimum 100 mm dia borewell gipipe2000mmlong,80/50mm,terminal50mmx6mm gi strip 22 supply & laying following size earth stripin horizontal or verticalruninground/surface/recessincludingriveting, soldering,saddles,jointingshallbedonebyoverlapping and with 2 set of brass (for cu strip) / gi (for gi strip) nut bolt&springwasherspacedat50cmmakingconnection etc.asrequired. allasperpreapprovedbyengineerin charge. foradditionaltechnicalparametersofproducts/ work, refer annexure a attached with this bsr. 25mm x 3mm g.i. ( hot dipped) strip 23 s i t c of star ratedaluminium wound distribution transformerof following rating 11/0.433kv delta star connected, vector group dyn 11,onan cooled & as per bee star level 2 & bis approved as per is 2026 1977 &lossesas definedasperis1180parti2014.includingstandard accessorieslike conservator, silica gel breather, radiator, fins, ht cable box & lt cable boxes, temperature rise in winding/oil 35 40 degree c upto 200 kva & 40 45 degree cforabove200kva,isimarkeddrainvalve,dialtypetemperaturegauge, first filling of transformer oil as per is :335 1953, epoxy based paint,including carrying of pre commission testing & charging of transformer complete in all respect.nablaccredeated /cpri/erdalabtestingreportswithoem certificate must submitted to engineer in charge .transformer must be tested fromctltestlabofdiscom(ifreqd.)beforechargingoftransformer& completeinstallaionmustbecertifiedfromelectricalinspectorateofficeas perindianelectricityrule,ctltestingcharges &inspection chargesshall be reimbursed by the department to the contractor as per actual expenditure. all as per pre approved by engineer in charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr . 250 kva with off ltc (+5% to 10% @ 2.5%) 24 supply & fabrication steel structure with ms channel / angle / joist / ismb / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as requiredcomplete in all respect. all as per pre approved by engineer incharge.foradditional technicalparameters of products/ work, refer annexure a attached with this bsr . 25 earth work in excavation/ by mechanical means (hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sum on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed: 26 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in: cement mortar 1:6 ( 1 cement : 6 sand). 27 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m15 grade nominal mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 40mm nominal size). 28 plaster on new surface on wall in cement sand mortar 1:3 including racking of joints etc. complete fine finish : 25 mm thick 29 providing & fixing of ip 51 ( upto 500) v range volt meter on existing panel as per pwd specification for electrical works, making connection bypvcinsulatedcopperconductorwithpvcsleeves/channeletc. metershallgivetruermsmeasurments,acc.ci1.0orbetter,with fieldprogrammableprimary&sec.valuespt(vt)primaryupto2000 kv.field programmablehighandlowthresholdvalues,metershall compliance of is 13875 & iec 61236. as required. oem must have bis certificateand & shallhavesubmit nabl/cpri/erda labtest reports beforeexecution&allasperpreapprovedbyengineerin charge.for additional technical parameters of products/ work, refer annexure a attached with this bsr .digital type 30 providing & fixing ofct operated direct reading type ip 51ampere meter on existing panel as per pwd specification for electrical works, making connection by pvc insulated copper conductor with pvc sleeves / channel etc. ampere meter shall give true rms measurement, acc. cl 1.0 or better , measuring current range 50 ma to 6 a, with field programmable primary and secondary values ct primary up to 15000 a,field programmablehighandlowthresholdvaluesasrequired. compliant to is 13875, & iec 61326. oem must have bis certificate and & shallhavesubmit nabl/cpri/erda labtestreports before execution&.allasperpreapprovedbyengineerincharge. for additionaltechnicalparametersofproducts/work ,referannexure a attached with this bsr . digital type confirming to iec 62053 21 below 500 a 31 supply and fixing of following accessories for moulded case circuitbreaker(mccb) compatibletomainmccboemas perpwdspecificationforelectricalworks,conformingto is/iec60947p 2:2003includingmakingconnectionetc complete in all respect. oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution. allasperpreapprovedbyengineerincharge. foradditionaltechnicalparametersofproducts/work , refer annexure a attached with this bsr . extended rotary handle 32 providing & fixing of 240/415 v isolator as per pwdspecification for electrical works with isi marked is:13947 iii/conforming to iec 60947 3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage,true contact indication,red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheetincluding makingconnections,testingetc.asrequired.oemshall havesubmit nabl/cpri/erdaaccrediatedlabtest reports beforeexecution&allasperpreapprovedby engineer in charge.for additional technical parameters of products/work ,referannexureaattachedwiththis bsr.four pole isolator 63 a rating 33 80/100 a rating 34 supplying and makingend termination with heavyaluminiumlugs pin / ring type (as per is 8309 1993 & is 8337 1976 ) duly crimped with crimping tool, pvc tapeas per pwd specification for electrical works etc of following size.allasperpreapprovedbyengineer incharge.for additional technical parameters of products/ work, refer annexure a attached with this bsr 35 16.0 sq.mm 36 25.0 sq.mm 37 35.0 sq.mm 38 185.0 sq.mm 39 300.0 sq.mm ...

Rajasthan Rajya Vidyut Utpadan Nigam Limited - Rajasthan

32938174 procurement of transformer of 300 kva, 415 v (delta) / 433 v (star), copper wound, dry type (vpi), indoor installation type with enclosure for acdb of unit 1 and 2 of lt swgr of ctpp, chhabra procurement of transformer of 300 kva, 415 v (delta) / 433 v (star), copper wound, dry type (vpi), indoor installation type with enclosure for acdb of unit 1 and 2 of lt swgr of ctpp, chhabra , transformer of 300 kva, 415 ( dlta)/ 433 v ( star ), copper wound, dry type (vpi), indoor installation type with enclosure rated power 300 kva pri. 415v±2.5%±5% (delta) sec. voltage 433v(star) amp. pri. 417.36 amp. sec. 400.01 phase3 frequency50hz impedance4.85% coolingan vect. group ref.dyn 11 type dw insulation class f amb. temp. 50 °c rise tmp 90 °c terminal arrangement on primary and secondarythru terminal box ( cable box )...

Indo Tibetan Border Police - Rajasthan

32892368 bids are invited for utp cat6 cable box 305 meter per box , information outlets cat 6 single port , patch panel 24 port cat6 , utp cat6 patch cord 1 meter , utp cat6 patch cord 2 meter , ofc cable 12 core, sm , optical fiber patch cord sm, sc lc 3 mtr , optical fiber pigtail mm sm sc type, 1 mtrs , liu 12 fiber with lc sm coupler loaded rm , liu 24 fiber with lc sm coupler loaded rm , 19 rack wall mount 9u , 19 rack floor mount 42u , supply of 15 15 mm pvc duct , supply of 25 25 mm pvc duct , supply of 25 45 mm pvc duct , supply of pvc conduit pipe 25mm , supply of 2 diameter hdpe pipe , supply and installation of buffer tubing kit , utp cable laying , installation of information outlet , installation ofpatch panel port , testing of nodes penta scan , installationof 15 15 mm pvc duct , installation of 25 25 mm pvc duct ,installation of 25 45 mm pvc duct , installation of 25mm pvcconduit pipe , installation of 2 diameter hdpe pipe 2 inch ,laying of fiber cable outdoor , splicing of ofc pigtails ,testing of ofc cable , digging of soil , supply installation offiber optic , installation of floor mount rack , layer 2manageable 24 port switch , layer 3 switch 24 port sfp ,1000 base lx transceivers with lc , 1000 base tx transceivers for copper , stacking module of 10 gbps withstacking cable total quantity : 7694...

Jodhpur Development Authority - Rajasthan

32771781 supply of electrical equipment in barktulla khan stadium sitc of wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as per pwd specification for electrical works, made out of crca sheet . other parameters required as per point (a) ,(b), (c),(d) below: (a)thickness of sheet shall not be less than 1.6 mm up to 600 mm length / width of any compartment and be of 2.0 mm above 600 mm. load bearing structure shall be of 2.0 mm thick sheet supported by base m.s. channel if required . side walls and cable alley compartments having bolted type doors with / without detachable extension type structure (b)panel shall be duly treated for derusting in 7 tank process with dephosphating and with powder coating of minimum 70 microns on both side of panel in desired shade the panel having pu/ neoprene rubber gasket of not less than 3mm thickness ,required hardware, separate detachable gland plate m.s. base channel (min75mm) , hinged door with locking arrangement for equipment/switchgear [c) interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 125 amp ) and by solid bus bar (>125 amp ) . all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. (d) only outer area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator. all as per drawing pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . 50.00 sq.mtr. 3443.00 172150.00 2 e081101 providing & fixing of ip 51 multi function meter as per pwd specification for electrical works, isi marked (is 16444)/ confirming to iec 61557 & iec 62052 with lcd/ led 3/4 line display capable of measuring electrical parameters like v, i, f, pf, kw, kva, kvar, kwh, kvah, kvarh display with 1a/5a ct input for lv/ hv network, with /without rs 485 communication port etc. oem must have bis certificate and & shall have submit nabl / cpri / erda lab test reports before execution & complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . multifunction lcd meter with v,a,f,pf,kw,kva, old energy memory, class 1 accuracy without rs485 port . 5.00 each 3483.00 17415.00 3 e080201 supplying and fixing of aluminium (iec 60105 iso 209 1,2) / copper (iec 60028) bus bar as per pwd specification for electrical works, by means of smc / dmc type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . electrolytic grade aluminium bus bar 6010 grade 350.00 kg. 445.00 155750.00 4 e080703 providing & fixing of bis approved current transformer as per pwd specification for electrical works ,isi marked as per is 2705 1992/ conforming to iec 60044 1, with secondary terminal of ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as required current transformer resin cast wound primary / ring type tape wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm (minimum), including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . 400/5 to 1200/5, burden 15 va 25.00 each 472.00 11800.00 5 e110400 providing & covering of existing cable lying in existing trench by iind class bricks/ stone slab of minimum 32mm thick and 250 mm wide in complete running length of trench complete as required. 100.00 mtr. 44.00 4400.00 jodhpur development authority, jodhpur g schedule name of work : cjdr qyykg [kk ¡ lv sfm;e e sa fofhkuu fo| qr midj.k yxku s dk dk; za s.no bsr code item qty. unit rate amount (rs.) 6 e110500 labour charges for excavation of 30cmx75cm size trench in loose soil including refilling of excavated earth,compaction of earth, making good the same complete as required . 100.00 mtr. 59.00 5900.00 7 e110140b providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un armoured / armoured aluminium cable of 1.1 kv grade as per pwd specification for electrical works in existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below: (a) material : h4 grade aluminium conductor of purity >99.6 % & as per is:1554 p i / is :7098 p i (b) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999 for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures . (c) oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities for cables . appropriate type test certificate / oem test report shall be submitted . all above as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . armoured cable 120.0 sq. mm 3.5 core 50.00 mtr. 482.00 24100.00 e110142b 185.0 sq. mm 3.5 core 200.00 mtr. 707.00 141400.00 8 e130103 providing & laying xlpe insulated as per is:7098/ii/85 h.t.cable as per pwd specification for electrical works for working voltage 11 k.v.(e) in existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size as per points (a), (b), (c) mentioned below: (a) material : h4 grade aluminium conductor of purity >99.6 % & as per is:1554 p i / is :7098 p i (b) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999 for armouring of cables , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures (c) oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities for cables . all above as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . 3 core 185.0 sq.mm 200.00 mtr. 953.00 190600.00 9 e130300 providing & laying of 25 cm thick layer of river sand to cover of existing cable in 30 cm x 100/ 120 cm size cable trench with levelling and making symmetric 25 mm thick layer in complete running length of trench as required. 100.00 mtr. 54.00 5400.00 10 e130400 providing & covering of existing cable lying in existing trench by iind class bricks/ stone slab of minimum 32mm thick and 250 mm wide in complete running length of trench complete as required. 100.00 mtr. 44.00 4400.00 11 e130500 labour charges for excavation of 30cmx100cm size loose soil trench including refilling of excavated earth,compaction of earth, making good the same complete as required . 100.00 mtr. 79.00 7900.00 12 e131300 providing & making heat shrinkable type indoor/outdoor/straight through terminations/ joint kit as per pwd specification for electrical works suitable for 11 kv / 33 kv cable with required components, prepration of cable ends. type test report should be as per is13573:2011 which covered all sequence for table 2 for termination kit and table 3 for streight through joint inclusive thermal & dynamic short circuit test, humidity test, soil fog test. cross linking shall be done out side factory with e beam/ peroxide technology. extrusion process shall be in house oem within same vicinity. oem test lab should be as per iso 9001:2015 & 14001 : 2015 & reports submitted to engineer in charge including testing etc. as required of following sizes. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . e131324 11 kv end termination kit outdoor type 3 core 240/300 sq.mm 8.00 each 5375.00 43000.00 e131323 11 kv end termination kit outdoor type 3 core 120/150/185 sq.mm 12.00 each 4920.00 59040.00 e131334 11 kv straight through joint kit 3 core 240/300 sq.mm 2.00 each 12327.00 24654.00 s.no bsr code item qty. unit rate amount (rs.) 13 e110221f providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un armoured / armoured copper cable of 1.1 kv grade as per pwd specification for electrical works in existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below: (a) copper conductor of electrlytic grade copper, purity >99.97 % isi marked as per is:1554 p i / is :7098 p i, b) conductor shall made of copper rods confirming to is 613 1964, is 3975 1999 for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures, (c) oem must have iso 9001 & 14001 certifications & its own in house nabl lab setup for all testing facilities for cables . appropriate type test certificate / oem test report shall be submitted . all above as per pre approved by engineer in charge. for additional technical parameters of products/ work, refer annexure a attached with this bsr . armoured 1.5 sq.mm. 7 core 25.00 mtr. 136.00 3400.00 e110223c 4.0 sq.mm. 4 core 25.00 mtr. 172.00 4300.00 14 e060113 providing & fixing of 240/415 v ac mcb with positive isolation of breaking capacity not less than 10 ka (b/ c tripping characteristic as per type of load and site requirement) 4kv impulse withstand voltage, as per pwd specification for electrical works with isi marked is 8828(1996) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 a rating and 10,000 upto 63 a, 5000 for 80 a rating including making connections, testing etc. as required. . oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr. single pole mcb 6 a to 32 a rating 40.00 each 142.00 5680.00 15 e121001 providing & laying of double wall corrugated pipe confirming to is : 14930 p 1 & 2 with hdpe coupler at 1 mtr. depth below the ground for laying cable including making the trench and back filling , compaction of earth as required( excavation of earth to be paid extra as required. ) of following outer dia. / inner dia as per is:4984:1995. all as per pre approved by engineer in charge. for additional technical parameters of products/work , refer annexure a attached with this bsr.55/50 mm 800.00 mtr. 66.00 52800.00 16 e140512 sitc of chemical gel earthing system of dual pipe technology made of with b class g i pipe as per is 1239 ( part 1):2004 of medium duty of following sizes as per points mentioned (a), (b), [c), (d), (e) below : (a) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, cpri/ erda tested with rms capacity of minimum 35 40 ka for withstanding 1 second (b) to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated lab for low resistivity ( less than 0.12 ohm meter) & high conductivity in nature with carbon as a major content as per referance of is 3043 1987,ieee 80 2013 (clause 14.5d) , ieee 837 & ier 1956 with latest amendemnts ©heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height 250 to 300 mm. (d) testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. (e) self certificate for confirming above standards from oem is mandatory. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . with pipe in pipe technology (outer pipe dia. / inner pipe dia. ) minimum 100 mm dia borewell gi pipe 2000 mm long, 80 / 50 mm, terminal 50mm x 6 mm gi strip 35.00 set 5007.00 175245.00 s.no bsr code item qty. unit rate amount (rs.) 17 e140608 supply & laying following size earth strip in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, jointing shall be done by overlapping and with 2 set of brass (for cu strip) / gi (for gi strip) nut bolt & spring washer spaced at 50cm making connection etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr. 25mm x 3mm g.i. ( hot dipped ) strip 100.00 mtr. 50.00 5000.00 18 e230205 s i t c of star rated aluminium wound distribution transformer of following rating 11/0.433kv delta star connected, vector group dyn 11,onan cooled & as per bee star level 2 & bis approved as per is 2026 1977 & losses as defined as per is 1180 part i 2014. including standard accessories like conservator, silica gel breather, radiator, fins, ht cable box & lt cable boxes, temperature rise in winding/oil 35 40 degree c upto 200 kva & 40 45 degree c for above 200 kva, isi marked drain valve, dial type temperature gauge, first filling of transformer oil as per is :335 1953, epoxy based paint, including carrying of pre commission testing & charging of transformer complete in all respect .nabl accredeated / cpri/ erda lab testing reports with oem certificate must submitted to engineer in charge .transformer must be tested from ctl test lab of discom (if reqd.) before charging of transformer & complete installaion must be certified from electrical inspectorate office as per indian electricity rule, ctl testing charges & inspection charges shall be reimbursed by the department to the contractor as per actual expenditure. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . 250 kva with off ltc (+5% to 10% @ 2.5%) 1.00 each 336210.00 336210.00 19 e231900 supply & fabrication steel structure with ms channel / angle / joist / ismb / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as required complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . 750.00 kg. 89.00 66750.00 20 e232000 earth work in excavation/ by mechanical means (hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sum on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed: 25.00 cum 622.00 15550.00 21 e232102 random rubble stone masonry for with hard stone in foundation and plinth in cement sand mortar above 30 cm thick wall in: cement mortar 1:6 ( 1 cement : 6 sand). 30.00 cum 2695.00 80850.00 22 e232202 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level. m15 grade nominal mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40mm nominal size). 28.00 cum 5749.00 160972.00 23 e232301 plaster on new surface on wall in cement sand mortar 1:3 including racking of joints etc. complete fine finish : 25 mm thick 60.00 sqm. 252.00 15120.00 24 e080400 providing & fixing of ip 51 ( upto 500) v range volt meter on existing panel as per pwd specification for electrical works, making connection by pvc insulated copper conductor with pvc sleeves / channel etc. meter shall give true rms measurments, acc. ci 1.0 or better , with field programmable primary & sec. values pt(vt) primary upto 2000 kv. field programmable high and low threshold values, meter shall compliance of is 13875 & iec 61236. as required. oem must have bis certificate and & shall have submit nabl / cpri / erda lab test reports before execution &all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr .digital type 5.00 each 1053.00 5265.00 25 e080611 providing & fixing of ct operated direct reading type ip 51 ampere meter on existing panel as per pwd specification for electrical works, making connection by pvc insulated copper conductor with pvc sleeves / channel etc. ampere meter shall give true rms measurement, acc. cl 1.0 or better , measuring current range 50 ma to 6 a, with field programmable primary and secondary values ct primary up to 15000 a, field programmable high and low threshold values as required. compliant to is 13875, & iec 61326. oem must have bis certificate and & shall have submit nabl / cpri / erda lab test reports before execution &. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . digital type confirming to iec 62053 21 below 500 a 5.00 each 1039.00 5195.00 s.no bsr code item qty. unit rate amount (rs.) 26 e090704 supply and fixing of following accessories for moulded case circuit breaker (mccb) compatible to main mccb oem as per pwd specification for electrical works, conforming to is/iec 60947 p 2 :2003 including making connection etc complete in all respect. oem shall have submit nabl / cpri / erda accrediated lab type test certificate before execution. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . extended rotary handle 40.00 each 2064.00 82560.00 27 e060332 providing & fixing of 240/415 v isolator as per pwd specification for electrical works with isi marked is:13947 iii/conforming to iec 60947 3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage, true contact indication, red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheet including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr.four pole isolator 63 a rating 10.00 each 590.00 5900.00 e060333 80/100 a rating 20.00 each 755.00 15100.00 28 e120300 supplying and making end termination with heavy aluminium lugs pin / ring type (as per is 8309 1993 & is 8337 1976 ) duly crimped with crimping tool, pvc tape as per pwd specification for electrical works etc of following size. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr ...

Rajasthan State Warehousing Corporation - Rajasthan

31681104 supply installation testing and commissioning of transformer substation supply installation testing and commissioning of transformer substation 250 kva and dg set 125 kva at gharsana, raisingnagar and head office rswc jaipur. , transformersubstations 250 kva , s i t c of star aluminium wound distribution of following rating 11 / 0.433kv delta star connected, vector group dyn 11, onan cooled & as per bee star level 2 & bis approved as per is 2026 1977 & lossesas defined as per is 1180 part i 2014. including standardaccessories like conservator, silica gel breather, radiator, fins, ht cable box & lt cable boxes, temperature rise in winding / oil 35 40 degree c upto 200 kva & 40 45 degree c for above 200 kva, isi marked drain valve, dial type temperature gauge, first filling of transformer oil as per is :335 1953, epoxy based paint, including carrying of pre commission testing & charging of transformer complete in all respect .nabl accredeated / cpri / erda lab testing reports with oem certificate must submitted to engineer in charge .transformer must be tested from ctl test lab of discom ( if reqd. ) before charging of transformer & complete installaion must be certified from electrical inspectorate office as per indian electricity rule, ctl testing charges & inspection charges shall be reimbursed by the department to the contractor as per actual expenditure. all asperpreapprovedbyengineerincharge. foradditionaltechnical parameters of products / work , referannexure a attached. 250 kva with off ltc ( +5% to 10% @ 2.5% ) , supply , installation, testing and comissioning of 11kv, 630 a, 25 ka / 1 sec, sf6 / vcb indoor type panel ht board, free standing motor operated & withdrawaltypefabricatedfrom2mmthickcrcasheetsteel, with ammeter, voltmeter, pf meter, kwh meter, mdi meter, selector switches as required, crt ct of required ratio ( 15va ; cl 1.0 / 0.5 ) pt ( 11 kv / 110v / v3 ) , fuses , ip42 protection, 4 / 8 / 10 / 12 window annunciation panel , ac / dc control voltage 24 / 48 / 110 / 230v , led indication lamps , s / c, o / c & e / f protection ( idmt ) relays alarm & trip contacts for transformer protection ( highoiltemperature, buchholzprotection, highwindingtemperature ) , power pack 2 x 12 v, etc complete in all respect ready to use ( rtu ) , oem must have bis certificate and&shall have submitnabl / cpri / erda lab type test reportsbefore execution complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work. , supply , installation, testing and comissioning of factory made11 kv, 630 a, 20ka / 3 sec, out door extensible type ip54 for panel & ip67 for main circuits ring main unit ( rmu ) iec 62271 200in suitable rcc foundation with 2 no. load break switch & 1 no. vcb / sf6 circuitbreaker with over load, earth fault, short circuit relay, copper bus bar, bus support and insulation marerial epoxy resin, ring core protection & metering ct, auxiliary relay for wti, oti , bucholz alarm & trip along with annuciator panel, master trip relay, mechanical on / off / earth indication, voltage presence indicator, shunt trip coil, 24 v dc power pack, digital multi function meter, with bus pt panel with 3 nos single phase voltage transformers of the ratio 11kv / v3 / 110 v / v3, 25 va, class 1.0 with ht fuses in the primary and mcb on the secondary side, voltmeter with selector switch, r y b phase indication, anti reflex operating handle, right angle boots etc. oem must have bis certificate and&shall have submitnabl / cpri / erdalab tpye test reportsbefore execution as requiredcompleteinallrespect.allasperpreapprovedbyengineerin charge. foradditionaltechnicalparametersofproducts / work , refer annexure a attached . , supply, installation, testing andcomissioning of1 no.vcb / sf6 circuit breaker coupled with existing extensible type rmuwith over load, earth fault, short circuit relay, copper bus bar, ring core protection ct 2.5 va, 10p10 as per transformer rating, mechanical on / off / earth indication, voltage presence indicator, anti reflex operating handle, right angle boots etc. as required complete in all respect. all as per pre approved by engineer in charge. foradditionaltechnicalparametersofproducts / work , refer annexure a attached. , supplyandfixingofiso / biscertifiedmadeaccessoriesof transformer above 500 kva rating i.e. winding temperature indicator ( wti ) , oil temperature indicator ( oti ) , magnetic oil level gauge ( mog ) , bucholz relay with alarm & trip contacts & marshalling box including making connection & testing etc as required complete in all respect. appropriate oem test reports of all items shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, referannexure a attached. , supply&installationofd.p.structurewithairbreakswitchhaving following specifications: all as per pre approved by engineer in charge.for additional technical parameters of products / work , refer annexure a attached with this bsr . dp : double pole structure on 2 no ismb 150 x 100 mm, 10 mtr high using 7 no ms channel each of size 100 mm x 50 mm x 2500 mm complete in all respect with nuts, springs washers, clamps as required. go:off load type gang operated 3 pole vertical flute type switch suitable for 11kv ; 400a , 3 ø, central post rotating double break isolator complete with ms hardware , copper moving & fixed contact , assembly of 9 nos pin insulator, gi pipe of suitable length for operation. do: 3nos vertical / horizontal mounted 11kv horn gap fuse set / drop out 11kv barrel fuses mounted on 6no pin insulators.la:3piecenonlinearresistortype.lightingarrestorofapprovedmake suitable for 3 wire, 11kv overheadline with rated voltage of 9kvrms & nominal discharge current rating of 5 ka & complete with galvanized clamping arrangement gi bolts, nuts, washer etc as required. jumpers: 3 no 11kv acsr conductors mounted on pin type insularors as required.6.general:thegoshallbeoperatedbyhandoperatedliver properly earthed with provision for locking mounted at 3’ , dg set ( 160 kva ) , supply , installation, testing and comissioning of silent dg set ( as per latest cpcb emission norms ) having specifications as per a, b, c, d, e, f, g, h , a.1500 rpm diesel engine conform to bs:649 / 5514 of suitable bhp engine shall have residential silencer ( isolated from main dg chamber ) , up to 3 m exhaust piping ( with insulation & cladding ) as required . , b.ac brush less spdp alternator conform to bs 5000 ( part 99 ) or is 4722. 2001 . alternator shall be self regulated with standard alternator protection ( over voltage , over speed & under voltage, under speed warning & shutdown ) .engine&alternatormountedonacommonbaseframe& coupled through a flexible coupling or close coupled , c. standard canopy with weatherproof, powder coated accoustic enclosure for dg set for sound attenuation fabricated from 1.6 mm crca sheet steel ( structure ) with side wall fabricated from 1.6 mm crca sheet & filled with glass wool ( 96kg / m3 ) / foam. as per is 8183 the doors of 28 / 40 / 50 / 85 mm thick as per rating and fabricated from 1.6mm crca sheet packed with accoustic material, all doors / opening are sealed with neoprene / epdn gaskets. the enclosure has built in fuel tank, with protection and tripping of dg set against temperature of more than 50 degree centigrade , d. electronic / mechanical governor, manual & electric start , batteries with battry charger, engine instruments panel, avm pads all controls for operation of dg set are from outside the enclosure with dg control panel having microprocessor based genset monitoring & control system, mccb / acb of suitable rating, ammeter, voltmeter, pf meter, frequency meter, kwh meter, digital fuel display meter, ind.lamps etc. mounted inside enclosure , visible and accessible from outside. the enclosure should be suitable for following capacity dg sets and alternator. noise level shall be less than 75 db at a distance of 1 mtrs. duly certified by authorised agency etc. complete in all respect of following capacity : , e. ( a ) accoustic glass wool wall thickness should not be less then 40mm and not less then 20mm pu foam upto rating 100 kva. ( b ) .accoustic glass wool wall thickness should not be less then 65mm and not less then foam upto rating 250 kva. ( c ) accoustic glass wool wall thickness should not be less then 100mm for rating above 250 kva. , f. first filling of the fuel tank shall be done by contractor and the prevailing fuel cost at that time shall be reimbursed to the contactor by department. , g. servicing of the dg set ( as per oem guidelines ) during the dlp period shall be done by contractor including all consumables, actual charges shall be reimbursed to the contractor by department / client complete in all respect. , h.oem must have bis certificate and&shall have submitnabl / cpri / erda / cpcb standards approved lab typetest reportsbefore execution as requiredcompleteinallrespect.allasperpreapprovedbyengineerincharge. foradditionaltechnicalparametersofproducts / annexure a attached. , radiator cooled & turbo charged / ac 160 kva at 0.8 pf 415v 50hz 3 ? , dg set ( 160 kva ) , supply , installation, testing and comissioning ofauto main failure ( amf ) panel fabricated from crca sheet steel 2 mmthick , powder coated finish , engine start & stopcommands, control relays , ammeter & voltmeterwith selector switches, control & 2 nos 4 pole power contactors with 2 no. of required size 4 pole mccb, timers, electronic hooter , visual & alarm indication for faults, ups, operator interface panel complete in all respect suitable for following capacity dg sets. oem must have bis certificate and& shall have submitnabl / cpri / erda lab type test reports before execution as required complete in all respect.all as per pre approved by engineer in charge. foradditionaltechnicalparamet .plc based 160 to 200 kva , providing & laying xlpe insulated as per is:7098 / ii / 85 h.t.cable as per pwd specification for electrical works for working voltage 33 k.v. ( e ) in existing rcc / hume / stoneware / pvcpipe / openduct / cabletrenchwith filling of excavated earth in trench, on existing cable trays or on surface etc.including making necessary connection, testing etc.as required of size as per points ( a ) , ( b ) , ( c ) mentioned below: ( a ) material : h4 gradealuminium conductor of purity >99.6 %& as peris:1554 p i / is :7098 p i ( b ) conductorshallhaveelectrolyticaluminium confirming to is 8130, is 3975 1999for armouring of cables , is 5831 for sheath, is 10810 ( part 0 to 64 ) for testing procedures ( c ) oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities forcables .all above as per pre approved by engineer in charge.for additional technical parametersofproducts / work , refer annexure a attached. 3 core 300.0 sq.mm , providing & making heat shrinkable type indoor / outdoor / straight through terminations / joint kit as per pwd specification for electrical works suitable for 11 kv / 33 kv cable with required components, prepration of cable ends. type test report should be as per is13573:2011 which covered all sequence for table 2 for termination kit and table 3 for streightthrough joint inclusive thermal & dynamic short circuit test, humidity test, soil fog test. crosslinking shall be done out side factory with e beam / peroxide technology. extrusion process shall be in house oem within same vicinity. oem test lab should be as per iso 9001:2015 & 14001 : 2015 & reports submitted to engineer in charge including testing etc. as required of following sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached . 11 kv end termination kit outdoor type 3 core 240 / 300sq.mm , providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un armoured / armouredaluminium cable of 1.1 kv grade as per pwd specification for electrical worksin existing rcc / hume / stoneware / pvc pipe / open duct / cable trench with filling of excavated earth in trench, on existing cable trays or on surface etc.including making necessary connection, testing etc. as required of size andas per points ( a ) , ( b ) , ( c ) , mentioned below: ( a ) material : h4 gradealuminium conductor of purity >99.6 %& as peris:1554 p i / is :7098 p i ( b ) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 ( part 0 to 64 ) for testing procedures . ( c ) oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities forcables . appropriate type test certificate / oem test report shall be submitted. allaboveasperpreapprovedby engineerincharge. foradditionaltechnicalparameters of products / work attached . refer annexure a , 185.0 sq. mm 3.5 core armoured cable , 50.0 sq. mm 3.5 core unarmoured cable , additiomn: h scheduleinstallation cost with other necessary fitting / accessories including pedestal / foundation, gi / copper earthing & stripsetc. required forsmooth operation / functioning for the transformer anddg set. , less: rebate for buy back and taking away the old working 100kva transformer from site ( head office, jaipur ) ...

Government Medical College - Rajasthan

30265772 supply of printing and stationery items printing with paper , . l ..l ..n.— i‘0 12. computer paper 70 gsm for dot matriks printer 5” x 12” / 2 with numbering & printing 13. computer paper 70 gsm ( a grade mills ) for dot matriks printer s” x 672 with numbering & printing 14. diary with cover for bpl patient 18” x 22 / 6 ( 22 paper & 2 pining ) 70 gsm ( both side printing ) 15. patient history discharge & follow up card sheet with 10 page book size 18” x 22 / 4 printing 16. indoor ticket with number ( for payment & free category ) 16”x 13” 706w white & colour ( both side printing ) 17. 10” x 12” / 2 computer paper rim ( cash memo ) 18. 10” x 12” / 2 computer paper rim ( cash memo ) with numbering & printing b printing with paper ( a grade mills ) — on 6ogsm paper form size both side printing 19, f printing wiih paper ( a grade miiis ) on 6ogsm paper form size 16” x 26” both.side_printing printing with paper ( a grade mills ) on 6ogsm paper form size 16” x 26” / 2 ( without numbering ) koth side printing 20. 21. printing with paper ( a grade mills ) on 6ogsm paper form size 16” x 26 / 2 ( with numbering ) both side pflnting 22. printing with paper ( a grade mills ) on 6ogsm paper form size 16” x 26r / 4 both side printing 23. printing with paper ( a grade mills ) on 6ogsm paper rorm size 16” x 2678 both side printing — 24. printing with paper ( a grade mills ) — on 6ogsm paper form size 18 x 22 both_side_printing 2s. 1 printing wimh paper ( a grade milis ) — on 6ogsm paper form size 18” x 22” / 2 both side printing .—‘u... ji.j r!ipilipi? printing on card sheet 18.1 kg. both side printing printing on card sheet 18.1 kg. bothside printing t17”x 14” ) 33. printing on card sheet 18.1 kg. bothside printing ( 9.5” x 14.5 ) 34. printing on card sheet 18.1 kg. bothside printing ( 3” x 49 d craft paper envelope star craft with printing 35. craft paper envelope star craft with printing ( 14.5” x 17.s ( 1oo gsm ) star craft ] 36. craft paper envelope star craft with printing [ 14.s” x 17.s” 10o gsm normal craft ] 37. craft paper envelope star craft with printing ( 12.s” x 15:s” 1oo gsm normal craft ] craft paper tnvelope star craft with printing [ 1o.s” x 12.5” 1oo gsm normal craft ] 38. 39. craft paper envelope star craft with printing [ 11x s” 1oo gsm ] 40. craft paper envelope star craft with printing ( 9” x 4” 1o0 gsm ) 41. craft paper envelope star craft with printing [ 8.s” x 10.5” 1o0 gsm normal craft ] 42. craft paper envelope star craft with printing ( 4.5” x 4.5” 1o0 gsm normal craft ] 43. craft paper envelope star caaft with printing [ 11” , 14” x ray envelop 100 gsmj register leger paper with printing 70 gsm e 44. register leger pawer with printing 70 gsm ( 17” x 27” ( 1oo page ) l 45. register teger pawer with pninting 70 gsm [ 17” x 27’72 ( 100 page ) ] 29. ecg paper sheet 9108 bpl 30. ecg paper roil 57 mm ( single channel ) c 32. 31. file cover l0”x14’ with printing 2x0 gsm 46. register leger paper with printing f binding work kacchi and pad binding service book gpf si pass book binding 78. letter pad for blood bank 70 gsm paper 18” x 22” / 6 88. stamp pad 110 mm x 70 mm _____ stamp pad 160mm x 97 mm 90. stapler small 10 91. stapler bie size no. 24 / 6 92. stapler pins no. 1o 93. stapler pins no. 24 / 6 94. glass marking pencil botekin wooden handle 96. gum bottle 15oml gum bottle 300m1 79 blood doners certificate in multi colour on glassed card sheet 7.5 x 9.5” certificates in multi colour on glassed card sheet size 7.5” x 9.5” for 26 january, 1s august ( sample required ) white paper rim 17 x 27 70 gsm 80. 81. 82. type paper 70 gsm 83. —a carbon paper blue full scape size . —e—e carbonpaperbigsize —e b file cover with printing & lases ( superior quality 9 / 924 ) p 84. 85. 86. special file cover with printing & lases ( 18.1 kg card sheet ) 7 x 9y” p 87. stamp pad ink 50 ml 89. 95. 97. 98. gum bottle 700 ml f 99. pencil ( h. b. ) 100. ball pen 101. refill for ball pen 102. paper weight glass 103. paper weight plastic 104. file tag —8” ( 800 tag per bundle ) 105. permanent marker pen 1o6. cd marker pen —..k 107. t pin weieht 70 gsm 100gm per pkt. 108. index file 109. file ledger 110. file lase no. 924 1jj, plastic tap transparent 50 mt.1 112. plastic tap dispenser 113. gel pen — blue / green / black / red 114. plastic jug with 1 ) ltr, capacity 115. tumbler glass 116. trey 117. correction pen 9 ml 118. high uighter pen set. 119. page marker slip ( a0x3 ) 120. pin cushion plastic 121. clip pin pkt..office clip_3o 122. box file . 123. glue stick 15gm kores / fevistic / scotch or other brand 124. water proof bug for cycle sewer 125. plastic scale 12 126. calculator 12 digit 127. file pad 128. dak pad plastic 129. fiie flap 130. ceiling wex 131. cloth coated envelop 16x12 — 132. cloth coated envelop 11x 5 133. punching machine size smali / beg 134. register ( 100 pages ) 135 punching machine 136. heawy duty stapler ( specification: staple use 23 / 6 23 / 24, loading capacity: 1oo staples, stapling capacity: 21o sheets ) 137. stiaker for admission iicket slze .. .. ( 2x4 inch ) 138. two vehicle sticker ( 1.5x2 inch ) 139. four vehicle sticker ( 1.5x2 inch ) 140. sticker of biood bank bag in four colour i4>s? “ x 3xx ) — 141. i card with cover & lace ( sample required ) 142. carbon pawer a4 size .________ 14a. certificates frame . _______ 144. p.a.diary 145. slippad ( soosheet ) 146. ra peg page 250 147. siamp pad small — 148. stamp pad big 149. stamp ( seal ) 150. aerylic sheet a4 sb’c? rate per fnch — 151. plastic bag bottom folder single pocket 152. plastic bag botton folder double pocket 153. pencil eraser non dust 1s4. penclisharpener? — 15s. dak folder cloth coated ( a&m x28cm ) . 156. short hand note book 100 page 70 gsm 157. binter clip 32 mm solo — h computer stationery & consumable 158. glossy paper a4 size. lnkjet paper tmt reporting paper. 159. computer paper a4 size 7s gsm for laser printer 176. toner repairing (magnetic rollers) _____ 177. printer repairing (teflon fuser film sleeve) 178. hp laser pnntcr cartridge i 536 mfp 179. hp laser printer (‘artridgc 1566 (i ip — 78a) 180. lip laser printer cartridge 1020+ (lip — i2a) 181. hp laser printer cartridge p1007 160. computer paper a4 site 7s gsm for laser printer numbering & printing 161. compute paper rs size 75 gsm for laser printer 162. computer paper 7o gsm ror dot matriks printer (8’x 6”? 2) 163. computer paper 7o gsm for dot matriks printer (8x 673 with number) 164. computer pawer 70 gsm for dot matriks printer (8m x 10”/1) 165. computer paper 70 gsm ror dot matriks printer (10” x 12”/1) 166. computer paper 7o gsm for dot matriks printer (10” x 1272) 167. computer paper 7o gsm ror dot matriks printer (8” x 1072) with printing & numbering 168. computer paper 70 gsm for dot matriks printer (15” x 1273) 169. pen drive (16/32 gb) 170. s . computer re writable disk with cover (cd rw) 171. computer compact disk with cover (cd r) 172. toner refilling 173. toner repairing (drum) toner repairing (pcr) . — toner repairing (doctor/wiper blade) 174. 175. 18 . laser printer cartridge p1008 laser printer cartridge , cattridge , printer ribbon, cd r dvd r cd bag , usb mouse keygboard monitor , photo frame lan switch , cat 6 lan cable box , lan connectors rj cat 6 lan io box set , desmate label stickers for dot matrix printer , computer c mos bios battery , crimping tool lan cutter with cable cutter , punch down tool , lan tester , screw driver kit , pliers , tweezers pack of4 , external hard disk etc ...

Dr. S.N.Medical College - Rajasthan

30259085 supply of printing and stationery rate contract for supply of printing and stationery stationary and printing items , printing with paper ( a grade mills ) – on 60gsm paperform size 16” x 26” , printing with paper ( a grade mills ) – on 60gsm paperform size 16” x 26” / 2 ( without numbering ) , printing with paper ( a grade mills ) – on 60gsm paperform size16” x 26” / 2 ( with numbering ) , printing with paper ( a grade mills ) – on 60gsm paperform size 16” x 26” / 4 , printing with paper ( a grade mills ) – on 60gsm paperform size 16” x 26” / 8 , printing with paper ( a grade mills ) – on 60gsm paperform size 18” x 22” , printing with paper ( a grade mills ) – on 60gsm paperform size 18” x 22” / 2 , printing with paper ( a grade mills ) – on 60gsm paperform size 18” x 22” / 4 , printing with paper ( a grade mills ) – form size18” x 22” / 8 ( yellow paper ) 70 gsm & other colour , printing with paper ( a grade mills ) – form size18” x 22” / 8 ( white paper ) 70 gsm , computer paper 70 gsm for dot matriks printer 8” x 6” / 2 with numbering & printing , computer paper 70 gsm for dot matriks printer 5” x 12” / 2 with numbering & printing , computer paper 70 gsm ( a grade mills ) for dot matriks printer 5” x 6” / 2 with numbering & printing , diary with cover for bpl patient 18” x 22 / 6 ( 22 paper & 2 pining ) – 70 gsm ( both side printing ) , patient history discharge & follow up card sheet with 10 page book size : 18” x 22 / 4 printing , indoor ticket with number ( for payment & free category ) 16”x 13” 70 gsm white & colour ( both side printing ) , 10” x 12” / 2 computer paper rim ( cash memo ) , 10” x 12” / 2 computer paper rim ( cash memo ) with numbering & printing , printing with paper ( a grade mills ) – on 60gsm paperform size 16” x 26” both side printing , printing with paper ( a grade mills ) – on 60gsm paperform size 16” x 26” / 2 ( without numbering ) both side printing , printing with paper ( a grade mills ) – on 60gsm paperform size16” x 26” / 2 ( with numbering ) both side printing , printing with paper ( a grade mills ) – on 60gsm paperform size 16” x 26” / 4 both side printing , printing with paper ( a grade mills ) – on 60gsm paperform size 16” x 26” / 8 both side printing , printing with paper ( a grade mills ) – on 60gsm paperform size 18” x 22” both side printing , printing with paper ( a grade mills ) – on 60gsm paperform size 18” x 22” / 2 both side printing , printing with paper ( a grade mills ) – on 60gsm paperform size 18” x 22” / 4 both side printing , printing with paper ( a grade mills ) – form size18” x 22” / 8 ( yellow paper ) 70 gsm & other colour both side printing , printing with paper ( a grade mills ) – form size18” x 22” / 8 ( white paper ) 70 gsm both side printing , ecg paper sheet 9108 bpl , ecg paper roll 57 mm ( single channel ) , file cover10”x14”with printing280 gsm , printing on card sheet 18.1 kg.bothside printing ( 17” x 14” ) , printing on card sheet 18.1 kg.bothside printing ( 9.5” x 14.5” ) , printing on card sheet 18.1 kg.bothside printing ( 3” x 4” ) , craft paper envelope star craft with printing [ 14.5” x 17.5” ( 100 gsm ) star craft ] , craft paper envelope star craft with printing [ 14.5” x 17.5” 100 gsm normal craft ] , craft paper envelope star craft with printing [ 12.5” x 15.5” 100 gsm normal craft ] , craft paper envelope star craft with printing [ 10.5” x 12.5” 100 gsm normal craft ] , craft paper envelope star craft with printing [ 11”x 5” 100 gsm ] , craft paper envelope star craft with printing [ 9” x 4” 100 gsm ] , craft paper envelope star craft with printing [ 8.5” x 10.5”100 gsm normal craft ] , craft paper envelope star craft with printing [ 4.5” x 4.5” 100 gsm normal craft ] , craft paper envelope star craft with printing [ 11” x 14” x ray envelop 100 gsm ] , register leger paper with printing 70 gsm [ 17” x 27” ( 100 page ) ] , register leger paper with printing 70 gsm [ 17” x 27” / 2 ( 100 page ) ] , register leger paper with printing 70 gsm [ 17” x 27” / 4 ( 100 page ) ] , register leger paper with printing 70 gsm [ 17” x 27” ( 200 page ) ] , register leger paper with printing 70 gsm [ 17” x 27” / 2 ( 200 page ) ] , register leger paper with printing 70 gsm [ 17” x 27” / 4 ( 200 page ) ] , register leger paper with printing 70 gsm [ 17” x 27” ( 300 page ) ] , register leger paper with printing 70 gsm [ 17” x 27” / 2 ( 300 page ) ] , register leger paper with printing 70 gsm [ 17” x 27” / 4 ( 300 page ) ] , kachi binding ( duplicate 100 x 2 ) 16x26 / 2 , kachi binding ( duplicate 100 x 2 ) 16x26 / 4 , kachi binding ( duplicate 100 x 2 ) 16x26 / 8 , kachi binding ( duplicate 100 x 2 ) 18x22 / 2 , kachi binding ( duplicate 100 x 2 ) 18x22 / 4 , kachi binding ( duplicate 100 x 2 ) 18x22 / 8 , kachi binding ( triplicate 100 x 3 ) 16x26 / 2 , kachi binding ( triplicate 100 x 3 ) 16x26 / 4 , kachi binding ( triplicate 100 x 3 ) 16x26 / 8 , kachi binding ( triplicate 100 x 3 ) 18x22 / 2 , kachi binding ( triplicate 100 x 3 ) 18x22 / 4 , kachi binding ( triplicate 100 x 3 ) 18x22 / 8 , pad binding ( 100 papers pad ) 16x26 / 2 , pad binding ( 100 papers pad ) 16x26 / 4 , pad binding ( 100 papers pad ) 16x26 / 8 , pad binding ( 100 papers pad ) 18x22 / 2 , pad binding ( 100 papers pad ) 18x22 / 4 , pad binding ( 100 papers pad ) 18x22 / 8 , pad binding ( 300 papers pad ) 16x26 / 2 , pad binding ( 300 papers pad ) 16x26 / 4 , pad binding ( 300 papers pad ) 16x26 / 8 , pad binding ( 300 papers pad ) 18x22 / 2 , pad binding ( 300 papers pad ) 18x22 / 4 , pad binding ( 300 papers pad ) 18x22 / 8 , service book / gpf si pass book binding , letter pad for blood bank 70 gsm paper 18” x 22” / 6 , blood doners certificate in multi colour on glassed card sheet 7.5” x 9.5” , certificates in multi colour on glassed card sheet size 7.5” x 9.5” for 26 january, 15 august ( sample required ) * , white paper rim 17 x 2770 gsm , type paper 70 gsm , carbon paper blue full scape size , carbon paper big size , file cover with printing & lases ( superior quality 9 / 924 ) , special file cover with printing & lases ( 18.1 kg card sheet ) 7” x 9½” , stamp pad ink 50 ml , stamp pad 110 mm x 70 mm , stamp pad 160mm x 97 mm , stapler small 10 , stapler big size no. 24 / 6 , stapler pins no. 10 , stapler pins no. 24 / 6 , glass marking pencil , botekin wooden handle , gum bottle 150ml , gum bottle300ml , gum bottle 700 ml , pencil ( h. b. ) , ball pen , refill for ball pen , paper weight glass , paper weight plastic , file tag – 8” ( 800 tag per bundle ) , permanent marker pen , cd marker pen , t pin weight 70 gsm 100gm per pkt. , index file , file ledger , file lase no. 924 , plastic tap transparent 50 mt.1” , plastic tap dispenser , gel pen – blue / green / black / red , plastic jug with1½ ltr. capacity , tumbler glass , trey , correction pen 9 ml , high lighter pen set. , page marker slip ( 80x3 ) , pin cushion plastic , clip pin pkt. office clip 30 , box file , glue stic 15gm kores / fevistic / scotch or other brand , water proof bug for cycle sewer , plastic scale 12” , calculator 12 digit , file pad , dak pad plastic , file flap , celling wex , cloth coated envelop 16”x12” , cloth coated envelop 11”x 5” , punching machine size small / big , register ( 100 pages ) , punching machine ( specification: punching capacity 290 pages / sheets; punching distance: 70 / 80 mm; punching dia: 6.00 mm ) , heavy duty stapler ( specification: staple use 23 / 6 ~ 23 / 24, loading capacity: 100 staples, stapling capacity: 210 sheets ) , sticker for admission ticket size: ……………… ( 2x4 inch ) , two vehicle sticker , four vehicle sticker , sticker of blood bank bag in four colour ( 4½ x 3½ ) , i card with cover & lace ( sample required ) * , carbon paper a4 size , certificates frame , p.a. diary , slip pad ( 500 sheet ) , raw peg page 250 , stamp pad small , stamp pad big , stamp ( seal ) , aerylic sheet a4 size – rate per inch , plastic bag bottom folder single pocket , plastic bag bottom folder double pocket , pencileraser non dust , pencil sharpener , dak folder cloth coated ( 38cm x28cm ) , short hand note book 100 page 70 gsm , binder clip 32 mm solo , glossy paper a4 size. inkjet paper tmt reporting paper. , computer paper a4 size 75 gsm for laser printer , computer paper a4 size 75 gsm for laser printer numbering & printing , compute paper fs size 75 gsm for laser printer , computer paper 70 gsm for dot matriks printer ( 8”x 6” / 2 ) , computer paper 70 gsm for dot matriks printer ( 8”x 6” / 3 with number ) , computer paper 70 gsm for dot matriks printer ( 8 x 10 / 1 ) , computer paper 70 gsm for dot matriks printer ( 10 x 12 / 1 ) , computer paper 70 gsm for dot matriks printer ( 10 x 12 / 2 ) , computer paper 70 gsm for dot matriks printer ( 8 x 10 / 2 ) with printing and numbring , computer paper 70 gsm for dot matriks printer ( 15” x 12” / 3 ) , pen drive ( 16 / 32 gb ) , computer re writable disk with cover ( cd rw ) , computer compact disk with cover ( cd r ) , toner refilling , toner repairing ( drum ) , toner repairing ( pcr ) , toner repairing ( doctor / wiper blade ) , toner repairing ( magnetic rollers ) , printer repairing ( teflon fuser film sleeve ) , hp laser printer cartridge 1536 mfp , hp laser printer cartridge 1566 ( hp – 78a ) , hp laser printer cartridge 1020+ ( hp – 12a ) , hp laser printer cartridge p1007 , hp laser printer cartridge p1008 , hp laser printer cartridge p1106 ( hp – 88a ) , hp laser printer cartridge pro m403d , samsung laser printer cartridge xpress m2091 , brother laser printer cartridge dcp –l2520d , cannon cartridge for laser jet lbp 2900b ( cannon – 303 ) , cannon cartridge for model m241d , dmp printer cartridge ( epson fx 890 ) ( model no. s015329 ) ( original epson ) , printer ribbion for epson fx890 , cd r , dvd r , cdbag 40 cd , usb mouse optical wired , usb keyboard computer wired , tvs gold usb wired keyboard , led monitor 17 inch , led / monitor19 inch , photo frame 12*10 ( steel ) , 5 port lan switch , 8 port lan switch , 16 port lan switch , cat 6 lan cable box ( 305mtr ) , lan connectors ( rj – 45 ) , rj 45 cat 6 lan i / o box set ( with i / o box, faceplate and i / o keystone jack ) , desmate label stickers for dot matrix printer ( 100 mm x 48mm ) , computer c mos bios battery , crimping tool lan cutter with cable cutter , punch down tool , lan tester , screwdriver kit , pliers , tweezers pack of 4 , external hard disk for data backup 2tb...

North Western Railway - Rajasthan

30072887 supply of poh kit for kbi make emergency brake cable box for lhb coaches consisting 7 items.poh kit for kbi make emergency brake cable box for lhb coaches consisting 7 items.,poh kit for kbi make emergency brake cable box for lhb coaches consisting 7 items. (1) kbipart no. b73364/3. description valve head qty/set 01 (2) kbi part no. 455588. description lock washerqty/set 01 (3) kbi part no. 456790. description clamping pin, qty/set 01 (4) kbi part no. 459143. description clamping pin, qty/set02 (5) kbi part no. 461043. description lock washer, qty/set 01 (6) kbi part no.461664. description toothed washer, qty/set 02 (7) kbi part no. 465632. description spring, qty/set 01carriage stores depot rajasthan 51.00 set...

Ministry Of Defence - Rajasthan

28561661 bids are invited for boq total quantity : 1 1 repair to veh ba no 02d 147807x eicher oil, diesel and air filter, engine , brake and housing oil, fan belt 2 replace of brake pad set, rear brake, bush kit, mirror, cable, box, wiper, bush etc. 3 pinion oil seal , steering bearing, steering boot, front glass channel, glass channel seal, door handle, plate washer , silencer packing, battery clips, self starter mico 4 materials and labour for replacement of the following items : indicator bulb, head light assy 5 materials and labour for replacement of the following items : water pump assy , radiator hose, radiator cap ...

All India Institute Of Medical Sciences - Rajasthan

27136986 supply of general it items 1. ofc pigtails multimode sc mm(50um) orange colour. om2 simplex 1m. sc connector 2. ofc om2 multimode patch cords lc/lc mtrs. 3. unifi ap hd (2.4 mhz 800 mbps) 4. unifi ap ac lr 5. cat 6 utp cable box (305 mtr.) 6. telephone cable (2 pair 90 mtr.) 7. ofc single mode 6 pair armored...

Department of Information Technology and Communication - Rajasthan

26927221 rate contract rfp for stationary, computer media, consumables and other office items oem new toner & ink cartridge ( with standard oem warranty ) 2 : refurbishing of toner 3 storage, memory & others 7. electric kettle ( prestige pkoss, borosil ) , 1 litre per piece 8. tea flask ( milton ) thermosteel carafe 1litres per piece 9. best quality white window envelop ( 50 piece ) 11 x 5 80 gsm per pkt. 10. towel 100% cotton, 75 cm x 150 cm ( bombay dyeing ) networking services 1. 9 u rack with pdu & ventilator per rack 2. installation charges for 9 u rack per rack 3. information outlet with smb ( dlink / digisol / dax / amp / molex ) / per piece 4. face plates ( d link / digisol / dax / amp / molex ) per piece 5. cat 6 network cable box 305 mtr. ( d link / digisol / dax / amp / molex ) per box 6. laying of cat 6 cable 7. isi mark pvc casing 1 inch per meter 8. laying of pvc casing per meter 9. 5 port switch 10 / 100 / 1000 mbps ( dlink / digisol / digilink ) per piece 10. 8 port switch 10 / 100 / 1000 mbps ( dlink / digisol / digilink ) per piece 11. wireless access point cum router ( dlink / digisol / digilink ) per piece 12. rj 45 connector ( dlink / digisol / digilink / molex ) per piece 13. hdmi cable – 15 mtr ( kramer / extron / crestron ) per piece 14. hdmi cable – 20 mtr ( kramer / extron / crestron ) ...

North Western Railway - Rajasthan

23925090 supply of , poh kit for kbi make emergency brake cable box to kbi part no. npzi 5 or similar for lhb coaches. firms offer poh kit for kbi make emergency brake cable box for lhb coaches as per list of 07 items attached...

North Western Railway - Rajasthan

22158330 supply of set of connector & poh kit for kbi make emergency brake cable box., set of connector kbi part no. stn 30979, poh kit for kbi make emergency brake cable box for lhb coaches consisting 7 items. ( 1 ) kbi part no. b73364 / 3. valve head qty / set 01 ( 2 ) kbi part no. 455588. lock washer qty / set 01 ( 3 ) kbi part no. 456790. clamping pin, qty / set 01 ( 4 ) kbi part no. 459143. clamping pin, qty / set 02 ( 5 ) kbi part no. 461043. lock washer, qty / set 01 ( 6 ) kbi part no. 461664. toothed washer, qty / set 02 ( 7 ) kbi part no. 465632. spring, qty / set 01...

North Western Railway - Rajasthan

22035104 supply of set of connector & poh kit for kbi make emergency brake cable box., set of connector kbi part no. stn 30979, poh kit for kbi make emergency brake cable box for lhb coaches consisting 7 items. (1) kbi part no. b73364/3. valve head qty/set 01 (2) kbi part no. 455588. lock washer qty/set 01 (3) kbi part no. 456790. clamping pin, qty/set 01 (4) kbi part no. 459143. clamping pin, qty/set 02 (5) kbi part no. 461043. lock washer, qty/set 01 (6) kbi part no. 461664. toothed washer, qty/set 02 (7) kbi part no. 465632. spring, qty/set 01...

Commercial Taxes Department - Rajasthan

21897666 supply of office and computer stationery rate contract tonner , cat 6 cable box , i / o box , patch cord , laying of cat 6 cable with conduit , tonner refill , drum replacement , pcr / blade , tonner refill with chip , i 18 drum replacement for t nner 19 pcr”blade replacernc tonner nt for any 20 tonner refill 21 drum replacement 22 pcr / bladf. 7 tonner refill 24 excide slab battery 25 excide slab battery 26 fire extinguishers...

Department Of Information Technology - Rajasthan

21038210 rate contract rfp for stationary, computer media, consumables and other office items for a period of one year. 49. duster ( cloth ) 2ft x 2ft. 50. note sheet ( fs size 75 gsm paper ) green color 51. post it ( 3m ) a. size 3” x 3” 100 sheets b. size 1” x 3” ( 3 pcs, coloured ) 100 sheets 52. cell ( duracell ) a. pencil cell ( aa ) b. pencil cell ( aaa ) 53. pvc cards ( 100 pcs. ) box length – 85.6mm width – 54mm thickness – 40mil1. dustbin plastic min 8 litr. ( poly propylene plastic ) – ( cello / prestige / vip / orient / milton ) without cover 2. dustbin with cover min. 8 litr ( poly propylene plastic ) – ( cello / prestige / vip / orient / milton ) 3. dustbin with cover 15 ltr ( poly propylene plastic ) – ( cello / prestige / vip / orient / milton ) 4. water jug plastic ( 2 ltr. ) ( poly propylene plastic ) – ( cello / prestige / orient / milton ) 5. extension board ( make: belkin ) 4 socket 6 socket 8 socket 6. scissors ( kangaro munix ) 185 mm stainless steel 7. electric kettle ( prestige pkoss, borosil ) , 1 litre 8. tea flask ( milton ) thermosteel carafe 1litres 9. best quality white window envelop ( 50 piece ) 11 x 5 80 gsm 10. towel 100% cotton, 75 cm x 150 cm ( bombay dyeing ) 11. hawai chappal size 91. 9 u rack with pdu & ventilator 2. installation charges for 9 u rack 3. information outlet with smb ( d link / digisol / dax / amp / molex ) / 4. face plates ( d link / digisol / dax / amp / molex ) 5. cat 6 network cable box 305 mtr. ( d link / digisol / dax / amp / molex ) 6. laying of cat 6 cable 7. isi mark pvc casing 1 inch 8. laying of pvc casing 9. 5 port switch 10 / 100 / 1000 mbps ( dlink / digisol / digilink ) 10. 8 port switch 10 / 100 / 1000 mbps ( dlink / digisol / digilink ) 11. wireless access point cum router dlink / digisol / digilink ) 12. rj 45 connector ( dlink / digisol / digilink / molex ) 13. hdmi cable – 2 mtr ( cramer / atlona / a ten / other14. hdmi cable – 5 mtr ( cramer / atlona / a ten / other reputed ) 15. hdmi cable – 15 mtr ( cramer / atlona / a ten / other reputed ) 16. hdmi cable – 20 mtr ( cramer / atlona / a ten / other r...

Rajasthan Cooperative Dairy Federation Limited - Rajasthan

19641964 rfq for laying fiber cable and installation networking equipments in new plant of jaipur dairy. i 6core armurd fiber cable multi mode 2 comrack 9u rack with pdu and fan 3 cat 6 cable box 4 24 port giga bit switch with 4 sfp ports 5 liu 12 port port rack mountable fully loaded 6 24 port patch panel 7 ri 45 connecter box 8 giga bit media converter multi mode 9 spf module giga bit 10 fiber patch cord multi mode i mtr. 11 i / o box with face plate and smb 12 conduit pipe, flexible pipe, casing and capping 13 complete installation including fiber splicing, testing, rack, switch, patch panel sfp, liu, patch cord mounting fixing & configuration, activation, and crimping ect. with all required accessories...

Indian Army - Rajasthan

17986430 supply of stores for field electrification : 1 supply install, testing and commissioning of transformer copper wounded step down, outdoor type 11000 volts / 433 volts, 3 phase 4 wire, independence 4 5% including supply of all standard fitting / fixture as per is:2026 of 350 kva capacity and comprising of the following: ( a ) ht porcelain bushing & lt bushing with cable box ( b ) oil filling hole with flanged and bolted cover. ( c ) conservator with drain plug. ( d ) prismatic oil level gauge. ( e ) dehydrating silica get breather with oil seal. ( f ) pressure release valve. ( g ) thermometer pocket. ( h ) air release valve. ( j ) inspection cover. ( k ) lifting lugs for complete transformer. ( l ) covering lifting plug. ( m ) jacking lugs. ( n ) top filter valve. ( o ) drain cum bottom filter valve. ( p ) earthing belt stud. ( q ) off load tap change switch with locking arrangement for hv variation from ( +5% to ( ) 5% step 25% ( r ) rating & diagram plate ( s ) unidirectional roller wheel. ( t ) other accessories as per manufacturer design note: transformer shall be supplied inclusive of initial oil filling to appropriate level of insulation oil with desired dielectric strength....

Indian Army - Rajasthan

17968218 supply, installation and integration of equipment and accessories for access control at the entry / electrical installation gates of jaipur military station, : supply, installation and integration of equipment and accessories for access control at the entry / exit gates of jaipur military station ( specifications as given below ) . ( x ) self support tower. 30 mtr self support tower chemical earthing light emulation lamp solar power backup ( xi ) outdoor cat 6 cable. outdoor cat 6 network cable box ( xii ) armed cable. 1.5 mm 2 core armed cable ( xiii ) fiber. 6 core single mode fiber cable ( xiv ) rack. 9 u network rack with pdu fan ( xv ) out door liu. allow maximum four cables entry, compact size perfect for limited space din rail mount enclosures, ms / aluminum housing with seven tank process powder coating ( xvi ) 48 port liu. 8 port rack mount liu, rear side cable entry provision, suitable for installing various fiber couplers ( xvii ) media converter. 10 / 100 / 1000 fiber to fiber media converter, with led indication status, complies with ieee 802.3ab and ieee 802.3z ( xviii ) media converter chassis. rack mounted media converter ( xix ) fiber patch cord. sc to lc fiber patch cord ( xx ) conduit. 25 mm conduit for outdoor cable ( xxi ) conduit laying. laying of conduit ( xxii ) system integration. one time system integration and testing...

Indian Army - Rajasthan

17928336 supply, installation and integration of equipments and accessories for access control at the entry / electrical installation gates of jaipur military station, : supply, installation and integration of equipments and accessories for access control at the entry / exit gates of jaipur military station specifications as given below ) ( i ) camera. ptz dome network camera, hdtv 1080p ptz with minimum 30 x zoom and focus recall ( ii ) nas. nas with 24tb enterprise / nas pro drive ( 8tb *3 ) . after raid useable space approx17tb ( iii ) license. camera license ( iv ) system. core i7 system with 16 gb ram, 1tb hard drive and 4 gb graphics card ( v ) led display. 43 inch led display ( vi ) hbs 5200. 5.8 ghz dual polarized mimo mode antenna with configurable channel bandwidth 10 / 20 / 40 mhz, support 250 mbps, throughput, ip 67 & poe supported, base station, support aes 128 / 256, fips 197 encryption ( vii ) sector antenna. 120 degree dual polarized sector antenna for base station ( viii ) hsu 525. 5.8 ghz dual polarized mimo mode antenna with configurable channel bandwidth up to 10 / 20 / 40 mhz, support 25 mbps, throughput, ip 67 & poe supported, subscriber unit, with 19 dbi integrated antenna, 128 / 256, fips 197 encryption ( ix ) poe. poe 55 volt, short circuit protection, auto recovery, over voltage protection ( x ) self support tower. 30 mtr self support tower chemical earthing light emulation lamp solar power backup ( xi ) outdoor cat 6 cable. outdoor cat 6 network cable box ( xii ) armed cable. 1.5 mm 2 core armed cable ( xiii ) fiber. 6 core single mode fiber cable ( xiv ) rack. 9 u network rack with pdu fan ( xv ) out door liu. allow maximum four cables entry, compact size perfect for limited space din rail mount enclosures, ms / aluminum housing with seven tank process powder coating ( xvi ) 48 port liu. 8 port rack mount liu, rear side cable entry provision, suitable for installing various fiber couplers ( xvii ) media converter. 10 / 100 / 1000 fiber to fiber me...

Indian Army - Rajasthan

17928282 supply of svl within system incl bullet vari focal camera, nas, desktop cmptr and other reqd hardware for jaipur military station ( a ) svl within system incl bullet vari focal camera, nas, desktop cmptr and other reqd hardware for jaipur military station ( specifications as given below ) ( i ) nas. nas with 24tb enterprise / nas pro drive ( 8tb *3 ) . after raid 6 useable spaces approx. 17tb. ( ii ) license. camera license for 10 cameras. ( iii ) system. core i7 system with 16 gb ram, 1tb hard drive and 4 gb graphics card ( iv ) led display. 43 inch led display ( v ) hsu 525. 5.8 ghz dual polarized mimo mode antenna with configurable channel bandwidth 10 / 20 / 40 mhz, support 25 mbps, throughput, ip 67 & poe supported, subscriber unit with 19 dbi integrated antenna, 128 / 256 fips 197 encryption. ( vi ) poe. poe 55 volt, short circuit protection, auto recovery, over voltage protection. ( vii ) self support tower. 30 mtr self support tower ( viii ) chemical earthing ( ix ) light emulation lamp ( x ) solar power backup ( xi ) outdoor cat 6 cable. outdoor cat 6 network cable box. xii ) armed cable. 1.5 mm 2 core armed cable. xiii ) fiber. 6 core single mode fiber cable. xiv ) rack. 9 u network rack with pdu fan. xv ) out door liu. allow maximum four cables entry, compact size perfect for limited space din rail mount enclosures, ms / aluminum housing with seven tank process powder coating. xvi ) 48 port liu. 8 port rack mounts liu, rear side cable entry provision, suitable for installing various fiber couplers. xvii ) media converter. 10 / 100 / 1000 fiber to fiber media converter, with led indication status, complies with ieee 802.3ab and ieee 802.3z. xviii ) media converter chassis. rack mounted media converter. xix ) gi pole. 6 mtr gi pole for camera mounting. xx ) fiber patch cord. sc to lc fiber patch cord. xxi ) conduit. 25 mm conduit for outdoor cable. xxii ) conduit laying. laying of conduiting....

Indian Army - Rajasthan

17876261 supply of access control eqpt incl ptz display, access pt, antenna and other accessories at the entry / exit gates of jaipur military station ( i ) camera. ptz dome network camera, hdtv 1080p ptz with minimum 30 x zoom and focus recall ( ii ) nas. nas with 24tb enterprise / nas pro drive ( 8tb *3 ) . after raid useable space approx17tb ( iii ) license. camera license ( iv ) system. core i7 system with 16 gb ram, 1tb hard drive and 4 gb graphics card ( v ) led display. 43 inch led display ( vi ) hbs 5200. 5.8 ghz dual polarized mimo mode antenna with configurable channel bandwidth 10 / 20 / 40 mhz, support 250 mbps, throughput, ip 67 & poe supported, base station, support aes 128 / 256, fips 197 encryption ( vii ) sector antenna. 120 degree dual polarized sector antenna for base station ( viii ) hsu 525. 5.8 ghz dual polarized mimo mode antenna with configurable channel bandwidth up to 10 / 20 / 40 mhz, support 25 mbps, throughput, ip 67 & poe supported, subscriber unit, with 19 dbi integrated antenna, 128 / 256, fips 197 encryption ( ix ) poe. poe 55 volt, short circuit protection, auto recovery, over voltage protection ( x ) self support tower. 30 mtr self support tower chemical earthing light emulation lamp solar power backup ( xi ) outdoor cat 6 cable. outdoor cat 6 network cable box ( xii ) armed cable. 1.5 mm 2 core armed cable ( xiii ) fiber. 6 core single mode fiber cable ( xiv ) rack. 9 u network rack with pdu fan ( xv ) out door liu. allow maximum four cables entry, compact size perfect for limited space din rail mount enclosures, ms / aluminum housing with seven tank process powder coating ( xvi ) 48 port liu. 8 port rack mount liu, rear side cable entry provision, suitable for installing various fiber couplers ( xvii ) media converter. 10 / 100 / 1000 fiber to fiber media converter, with led indication status, complies with ieee 802.3ab and ieee 802.3z ( xviii ) media converter chassis. rack mount...

Medical College - Rajasthan

17144656 supply of general and stationary items 55 hp laser printer cartridge model 88 a 56 hp laser printer cartridge 1536 mfp 57 hp laser printer cartridge 1566 (hp — 78a) 58 hp laser printer cartridge 1020+ (hp — 12a) 59 hp laser printer cartridge p1007 60 hp laser printer cartridge p1008 61 hp laser printer cartridge p1106 (hp — 88a) 62 laser printer cartridge model 303 63 cannon cartridge for laserjet 2900b (cannon —303) 64 cannon cartridge for model m241d 65 dmp printer cartridge (epson fx 890) ( model no. so15329) 66 usb mouse optical wired 7 keyboard computer wired ps 2 68 led monitor 17 inch 69 led monitor 19 inch 70 photo frame 12• l0 (steel) 71 computer paper 70 gsm for dot matrix printer size 8x10x 2 with printing and numbering (as per sample) 72 printer ribbion for epson fx890 73 5 port lan switch 74 8 port lan switch 75 16 port lan switch 76 cat 6 lan cable box (305mtr) 77 lan connectors (rj — 45) 78 rj 45 cat 6 lan 1/0 box set (with u0 box, faceplate and i/0 keystone jack) 79 desmate label stickers for dotmatrix printer (100 mm x 48mm) 80 laryngoscope bulb 3 v 81 plug with socat 5 amp isi/iso 82 round pin (cattle plug) 15 amp isms() 83 element 2 kv isuiso 84 element 6 kv isuiso 85 wall plug (power)15 amp isuiso 86 wall plug 5 amp isuiso 87 starter for tube light isuiso 88 three pin top 15 amp isuiso 89 three pin top 5 amp isuiso 90 tube light rod 36/40 w isuiso 91 electric call bell & switch (base type) isuiso 92 electric 1.5 kva for food trolley 9 cfl 11 watt pl2 pin type 94 cooler tata general size 650gm 95 cooler tata large sagar type 800gm 96 cooler tata sagar body 1.25 kg 97 cooler fan motor ring with nut bolt 98 cooler fan motor legs nut bolts set 99 cooler fan motor blead 18 inch (trim) 100 dmp fx 890(epson) ribbon 101 rubber wheel(trolley wheel) heavy duty 4 x v 102 rubber wheel(trolley wheel) heavy duty 6xl a 103 hexa blade 104 steel screw w, 105 steel screw 1, 106 steel screw 11/2, 107 steel screw 2 108 wooden screw/ ...

Indian Army - Rajasthan

17018601 rate of cctv surveillance system : 1 cat 6, 305 mtr. utp cable box 2 1 mtr patch cord 3 cat 6, keystone information outlet 4 single face plate 5 surface mount box => short tender notice...

Indian Army - Rajasthan

16814443 rate enquiry of cctv surveillance system : 1 cat 6, 305 mtr. utp cable box 2 1 mtr patch cord 3 cat 6, keystone information outlet 4 single face plate 5 surface mount box => short tender notice...

North Western Railway - Rajasthan

16171016 tender for kit for overhauling brake controls of axlemounted disc brake systemfor lhb/eog coaches as per given below: s. no. description qty/coach 1 overhauling kitfor check valve rv7 t (i90476) consisting of 3 items. 02 nos. 2 overhauling kit for cock dh7 te (i88738)consisting of 06 items. 02 nos. 3 overhauling kit for cock ahb 200nw19 (wbahb23oaa002) consisting of 9items. 02 nos. 4 overhauling kit for filter nw19 (wbfil100aa002) consisting of 3 items. 02 nos. 5overhauling kit for emergency brake cable box (ii18996) consisting of 7 items. 09 nos. 6 overhauling kit foremergency brake valve (i94023/a) consisting of 8 items. 01 no. 7 overhauling kit for dump valve(ii34652/15024) consisting of 7 items. 04 nos. 8 overhauling kit for indicator (i48102/w) consisting of 1 item 04 nos. 9 overhauling kit for distributor valve ke1ipksl (i.2.274) consisting of 49 items. 01 nos. 10overhauling kit for relay valve for dv (kr1) consisting of 11 items 01 nos. 11 overhauling kit for cock g1 dn25e (ii20882/14sx) consisting of 5 items. 02 nos. 12 overhauling kit for brake accelerator (189179)consisting of 21 items. 01 nos. 13 overhauling kit for angle cock (i.2.411/2) consisting of 4 items 08 nos. 14hose coupling fp (i75882/455/ki) 04 nos. 15 hose coupling bp (i75888/455/ki) 04 nos. 16 hose connection500mm (i.3.941/1) 08 nos. 17 hose connection 600mm (i.3.941/2) 04 nos.carriage stores depot rajasthan 27.00 set...

Hindustan Copper Limited - Rajasthan

4618321 supply of oil immersed power transformer with cable box ,3.3 kv/440v, 500 kva, 3 phase,50hz, vector group dyn11, oil natural air natural,max ambient temp 40 degree centigrade. details in attachment....

Hindustan Copper Limited - Rajasthan

2003267 procurement of power transformer through enterprise procurement system(oil immersed indoor type power transformer complete with accessories and with cable box ,3.3kv/440v, 500 kva, 3 phase, 50hz, vector group dyn11, oil natural air natural, max ambient temp40 degree centigrade)...