Rajasthan Rajya Vidyut Utpadan Nigam Limited - Rajasthan

37860596 supply of spares of safety valves tyco make or equivalent specification for boiler supply of spares of safety valves tyco make or equivalent specification for boiler , spare of ms line safety valve, valve model: 4p2 8hci w 88 c, sr no. 09 27332,09 27333, 09 27348,09 27349 lot containing below items and quantity as per appendix d of tender documents , nozzle ring , disc insert , disc holder , disc holder retainer , guide , guide ring , spindle assembly , bearing thrust washer , thrust bearing adapter , spindle nut , spring , spare of drum safety valve, valve model: 3m2 6he w 96 c, sr no. 09 27334 to 09 27339 & sr no. 09 27350 to 09 27355 lot containing below items and quantity as per appendix d of tender documents , bearing adapter , bearing thrust washer , spindle assembly , guide ring , educator , disc insert , disc holder retainer , disc holder , nozzle ring , spindle nut , spring...

Department Of Heavy Industry - Rajasthan

37760350 bids are invited for piston rod thrust bearing cylinder pipe piston rod , piston rod extension , cyinder pipe st , cylinder pipe , honned steel tube , thurst bearing b7 bronze casting , thurst collart b7 bronze casting , cylinder tube total quantity : 153...

Medical Health And Family Welfare - Rajasthan

37748513 tender for electrical work phc building janunda, district pali., 1 ( electrical bsr 2022 rajasthan ) wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thick hot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required. for specification of copper conductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr. short point ( up to 3 mtr. ) 2 medium point ( up to 6 mtr. ) 3 long point ( up to 10 mtr. ) 4 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modular box of 1.2 mm thick with earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required. for specification of copper conductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr. medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanized modular box of 1.2 mm thick with earth terminal, 10 a modular switch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required. for specification of copper conductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr. on board 7 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of isi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification of wiring accessories refer chapter e 07 related item & for additional technical parameters of product / work refer annexure a attached with this bsr 8 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along with isi marked ( is:3419 1988 ) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr. 20 mm 9 25 mm 10 32 mm 11 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existing surface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr. 1 x 1.5 sq.mm 12 2 x 2.5 sq. mm. + 1x1.5sqmm 13 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 14 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. 15 1 x 4.0 sq.mm 16 4 x 6.0 sq.mm 17 4 x 10.0 sq.mm 18 providing & fixing of isi marked surface type buzzer ( is:2268 1994 ) with cm / l no. printed including making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 19 p & f phenolic laminated sheet 2.0 mm thick of following size . including screws, cup washer as required.for additional technical parameters of product / work refer annexure a attached with this bsr. 75 mm dia 20 p & f 1.2mm thick m.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 21 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip 20 rating , including all as per pre approved by engineer in charge, making connections, testing etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr. 5 step fan regulator 2 module 360 dgree rotating 22 providing & fixing of following modular accessories as per pwd specification for electrical works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip 20 rating , including all as per pre approved by engineer in charge, making connections, testing etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr. blanking plate 23 25 amp. 2 module motor starter with on / off push button 24 providing & fixing of modular type lockable feature socket duly made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip 20 rating , including all as per pre approved by engineer in charge, making connections, testing etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr. 25 amp. 2 module socket 25 providing & fixing of extra down rod of 15 mm dia . erw ( electrical resistance welded ) of 1.6mm nominal thick medium duty steel pipe including cutting, threading, drilling, fixing quarter pin etc as reqd. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 26 p & f of gravity louver shutter of superior quality made out of frame of 18 swg m.s. sheet & louvers made from 24 swg ms sheet with enamel paint including cost of nuts, bolts, etc as reqd. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr .up to 380 mm size 27 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002 in existing surface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr. 3 pair 28 5 pair 29 50 pair 30 20 pair 31 p & f krone module with base frame in the recess / surface made out of 1.2 mm thick sheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferruling and punching of telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr. 20 pairs 32 50 pairs 33 p & f 1.2 mm thick g. i. / m .s. sheet boxes duly finished with two coats of red oxide and with earthing terminal of following sizes ( nominal size ) in recessed / surface as required.for additional technical parameters of product / work refer annexure a attached with this bsr. 1.2 mm thick m. s. sheet boxes 175mm x 100mm x 60mm 34 p & f paper phenolic resin bonded laminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc plated nut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr. 3.0 mm thick 35 providing & fixing of flush type non modular single line telephone jack made out fromindustrial grade polycarbonate or fire resistant abs material, including making connection testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 36 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected by pvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 37 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . cat 6, un sheilded information outlet 38 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should be pc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . single aperture 39 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load and site requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted in existing distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above rating including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab type test reports & all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr. single pole mcb ( with b / c curve tripping characteristics ) 6 a to 32 a rating 40 triple pole mcb ( with b / c curve trippingcharacteristics ) 6 a to 32 a rating 41 four pole mcb ( with b / c curve tripping characteristics ) 6 a to 32 a rating 42 50 / 63 a rating 43 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick  conforming to is 8623 1 & 3 /   iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp.  insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set  of suitable rating and din bar, masking sheet,   making internal db  terminations with copper lugs, ferrules,   detachable gland plate, including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab type test reports & all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr. metal door ( three phase ) ik 09 and ip 43 with metal end box 6 way 44 8 way 45 providing & fixing of 240 / 415 v residual current circuit breaker ( rccb ) conforming to ( is:12640 1 ) / iec 61008 1 , rated 4 kv impulse withstand voltage truly current operated and shall operate on cbct mechanisum, provision for pad lock, min. operation 10, 000 upto 63 a rating and 5000 for 100 a rating and minimum phase termination capacity of 35 sq.mm. rigid wire , ip 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab type test reports & all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr. four pole 100 / 300 ma sensitivity 63 a rating 46 providing & fixing of recessed / surface mounting heavy duty vertical tpn distribution board with metal end box with provision of incomer suitable for 3 / 4 pole mccb and sp / tp mcb as outgoing , made out from galvanized steel / crca sheet not less then 1.2 mm thick  conforming to is 8623 1 & 3 /   iec 61439 1 & 3. powder painted with reversible door ( for double door db only ) complete with insulated 160 ( upto 160 a incomer ) / 250 amp.  copper bus bar, neutral bars with shrouds,   earth bar , color coded interconnecting wire set  of suitable rating and din bar, masking sheet,   making internal db  terminations with copper lugs, ferrules,   detachable gland plate, including making connections, testing etc. as required.  oem shall have submit nabl / cpri / erda accrediated lab type test reports & all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr. double door ip 43 & ik 09 with provision of incomer mccb 160 a rating with metal end box 6 way 47 supply and installation of high tensile low carbon steel rod molecularly bonded with 99.9 % copper thickness ( 250 microns ) and confirming to ul 467, is / iec 62561 2 of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole ( b ) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, cpri / erda tested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated lab for low resistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major content as per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt. ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height 250 to 300 mm. ( d ) testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. ( e ) test certificates for confirming above standards from oem is mandatory. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 17.2 mm thick and 3 mtr. long 48 supply & laying following size earth strip in horizontal or vertical run in surface by means of earth strip dmc insulator including riveting / soldering / welding, jointing shall be done by overlapping and with 2 set of brass ( for cu strip ) / gi ( for gi strip ) nut bolt & spring washer spaced at 50cm making connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 25mm x 3mm copper strip 49 25mm x 3mm g.i. ( hot dipped ) strip 50 providing & fixing of bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan conforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 1200 mm sweep bee 1 star rated ( service value >=4.0 to < 4.5 ) 51 providing & fixing of heavy duty capacitor start, copper wound double ball bearing 900 / 1400 rpm single phase exhaust fan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr .300 mm sweep ( 900 / 1400 rpm ) 52 providing & fixing of of double ball bearing, copper wounded capacitor start single phase metallic blade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 225 mm sweep 53 providing & fixing of 450 mm sweep oscillating type wall mounting / pedestal type fans with three speed, on and off position, sintered iron bush oil impregnated, with metal front and back 120 or more ribs guard; three no. aluminium blades, minimum air delivery 100 cum. / minute , minimum service value 1.11 cum. / min / watt, noise level should be <= 75 db, power consumption <= 120 watts, motor protection through thermal overload protection device, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . wall mounting type with adjustable vertical angle 54 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminium housing with in built driver , system lumen efficacy ≥ 110 lm / watt output, internal surge protection of 2.5 kv with short & open circuit protection , thd < 10% , p. f.≥0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 1170mm ( + / 10% ) led batten with min. lumen output 2200 lm 55 providing & fixing of ip20, 2x2 led surface / recessed mounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of ≥ 120 lm / watt , thd < 10 % , p.f.≥0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . surface moutning minimum lumen output 3600 lm 56 providing & fixing of ip 20 led recessed / surface mounted, round / sqaure smd mid power led downlight with power coated die cast aluminum housing with uv stabilized non yellowish diffuser with bis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of ≥ 110 lm / watt, thd < 10 % , pf.≥0.95, cri >80, life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . surface mounting ( with extruded alumn. housing ) minimum lumen output 1950 lm 57 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmoured aluminium cable confirming to is:1554 p i / is :7098 p i of 1.1 kv with h4 grade electrolytic aluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831 in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) including testing etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr. 6.0 sq. mm 4 core 58 10.0 sq. mm 4 core 59 16.0 sq. mm 4 core 60 50.0 sq. mm 3.5 core 61 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as per is 8337 1976 of following size of pvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 4 x 6.0 sq.mm 62 4 x 10.0 sq.mm 63 3.5 x 50.0 sq.mm 64 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and other parameters required as per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: ( a ) thickness of crca sheet shall be 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel. the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only. all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgear is to be paid extra ) ( d ) wiring between components within switchgear and incoming / outgoing cable shall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. ( f ) floor mounted panel shall be mounted on base frame of ismc channel size 100 x 50 x 5 mm ( to be paid extra ) ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 65 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulator with standard short circuit withstand capacity , high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . electrolytic grade aluminium bus bar 6010 grade 66 providing & fixing of is: 13875 & iec :61326 confirming led digital type ( up to 500 ) v range volt meter / direct ammeter / ct oertated ammeter / frequency meter / kwh meter / multi function meter / power analyzer of class 1 accuracy as per is : 1248 of size 96mm x 96 mm including making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . three phase ammeter with inbuilt selector switch 67 three phase voltmeter with inbuilt selector switch 68 providing & fixing of bis approved current transformer as per pwd specification for electrical works , isi marked as per is 2705 1992 / conforming to iec 60044 1, with secondary terminal of ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as required current transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . ring type tape wound ct c t class 1, ratio upto 150 / 5, burden 5 va 69 providing & fixing of 110 / 220 v, unibody led indicating lamp iec 60947 with integral circuit, ip 65 above panel & ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min. 29 mm, contact material phospher bronze for led, pcb contacts shall be of brass ( tin plated ) , impulse dielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdc including connection etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . red / yellow / green colour 70 providing & fixing of electrical insulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006 with one side anti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 11 kv, class b 2.5 mm thick with proof voltage 22 kv ac ( rms ) and break down voltage 45 kv ac ( rms ) 71 sitc of 3 / 4 pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage 690 v. provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections etc. as required.oem shall have submit nabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr. 4 pole mccb with thermal magnetic release up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 72 160 amp , 25 ka, adjustable o / l & adjustable s / c setting, 73 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass cover and secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver & has a unique bis r number with input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driver efficiency >85% , thd ( i ) <10% humidity 10% to 90% rh working temp 5c to 45c . driver current <750ma. the luminaire shall be bis certified and trade mark certified. life expectancy equal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min ≥ 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs. manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . led street light fixture with minimum lumen output 3700 lm 74 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 32 mm dia. 75 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be of carbon + s.s.the stator body of single phase pump shall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submit nabl / cpri / erda accrediated lab type test certificate before execution. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 1.5 hp, 1 ø, ( 18 26 ) mtr, ( 126 78 ) lpm 76 supply & fixing of gi pipes confirming to is : 1239 p 1 ( 2004 ) with flanges duly screwed & welded including rubber washer, nuts & bolts of 8mm dia complete in all respect.all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . b class 50mm dia 77 sitc of contactor oem fabricated dol / star delta starter panel with switchgear selection as per type 2 cordinatiom chart and made out from 1.6 mm thick powder coated crca sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, illuminated on / off push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . for three phase submersible / mono block pump 3.0 hp to 5.0 hp ( star / delta starter ) 78 p / laying isi marked p.v.c. insulated submersible cable confirming to ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.90 % purity copper, stranding in acc. to is:8130 / iec 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, existing pipe / open trench / cable tray / on surface including making connection etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr. 6.0 sq.mm 3 core flat / round 79 supply, fabricating & installing following sizes of perforated hot dipped galvanized iron cable tray ( galvanized thickness not less then 50 microns ) with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers tees, cross members and other accessories as required and duly suspended from the ceiling with gi suspenders including gi bolts & nuts , fastners, supports etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 150mm x 50mm x 1.6mm 80 p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.for additional technical parameters of product / work refer annexure a attached with this bsr. 50mm x 50mm x 6mm 81 35mm x 35mm x 5mm 82 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specification for electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating. appropriate type test certificate / oem test report shall be submitted . all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . open execution type 125 a 83 providing & fixing of vertical ( bee 5 star rated ) / horizontal ( bee 3 star rated ) storage water heater with outer casing made of engineering plastic sheet ( upto 25 ltr ) / metal rust proof body ( 35 & 50 ltr ) , glass line / titanium enamel coated pressure pump compatible 8 bar pressure inner tank, glass line coated , mineral filled heating element, stem type, snap action adjustable thermostat , dual indicating lamps injected puf insulation, multi function valve etc. as required held in position with 2 / 4 no. 10 / 12 mm anchor fastener, duly wired with 3 core 2.5 / 4.0 sqmm pvc insulated & sheathed copper conductor and 16 a / 25a three pin plug top with portable residual current device ( prcd ) , including making inlet, outlet flexible alloy connection, testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 15 ltr. 84 providing & fixing of vertical ( bee 5 star rated ) / horizontal ( bee 3 star rated ) storage water heater with outer casing made of engineering plastic sheet ( upto 25 ltr ) / metal rust proof body ( 35 & 50 ltr ) , glass line / titanium enamel coated pressure pump compatible 8 bar pressure inner tank, glass line coated , mineral filled heating element, stem type, snap action adjustable thermostat , dual indicating lamps injected puf insulation, multi function valve etc. as required held in position with 2 / 4 no. 10 / 12 mm anchor fastener, duly wired with 3 core 2.5 / 4.0 sqmm pvc insulated & sheathed copper conductor and 16 a / 25a three pin plug top with portable residual current device ( prcd ) , including making inlet, outlet flexible alloy connection, testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 25 ltr. 85 supply, installation, & testing of 19 1u rack mounted / surface mounted aluminum / crca 1.2mm powder coated, singlemode glass fiber optic cable patch panel / liu loaded with flangless / screwable duplex adapters for st / e 2000 / sc / lc / mt rj / pc type, it should have easy removable top plate with push buttons, there should be a splice tray installed in the patch panel / liu which can handle the fiber cores, splice tray should be pc+abs material, it should include accessories like mounting hardware, gormetts, heat shrink tubes / sleevs, screws, nuts to install the panel for rack / wallmount applications as per requirment complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 24 ports 86 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 1 mtr 87 supply & installation of ip 20 & ik 08 , ul listed wall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastner etc as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 12 u rack with width 600 mm & depth 400 mm + 100 mm 88 supply , installation, testing and comissioning of managed layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 89 supply , installation, testing and comissioning of inverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and 50 hz , single phase ac supply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 1.5 tr iseer not less then 3.8 90 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrial plug top making connection etc complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 4 kva 91 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 92 supply , installation, testing and comissioning of is:1475 marked self contained drinking water cooler with hermetically sealed compressor, non cfc refrigerent suitable for operation on 230v / 1ph / 50hz ac supply, full stainless steel ( ss304 ) body ( 0.8 mm thick ) and tank ( 0.5 mm thick ) , stainless steel water tray, minimum two nos brass chrome plated faucets and suitable drainage system complete in all respect with required height ms fabricated and painted angle iron frame ( cost of frame to be paid extra ) complete in all respect of the following capacity. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . cooling capacity 150 ltr. / hr. and storage capacity 150 ltrs 93 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc type fire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificate from oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 4 kg 94 p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.for additional technical parameters of product / work refer annexure a attached with this bsr. 40mm x 40mm x 5mm 95 p & f of industrial plug and socket conforming to iec 60309 1 / 2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. for additional technical parameters of product / work refer annexure a attached with this bsr. ip 67 surface / wall mounted socket. 32 a 3 pin ( 2p+e ) ...

Sawai Man Singh Medical College - Rajasthan

37730443 rate contract supply of hardware items for two year at sms hospital jaipur swivel castor 4 inch x 1 inch for1 ¼inch pipe make fromheavy qualitywithout wheelci companymake embossing case iron 2 swivel castor 6 inch x 1 ½ inch for the conduit pipe fittings with thrust bearing with solid rubber wheel. company makeembossing 3 supply of swivel castor 8 inch x 2 inch for loading trolleyplate fittings with thrust bearing with solid rubber / hard plastic wheel including withall relatedaccessories asperhospitalrequirement .company makeembossing 4 supply of wheelchair caster front wheel approximate 6 inch including withall relatedaccessories asperhospitalrequirement .company makeembossing iron 5 supplyofwheelchair rear spoke wheel approximate size: 24 / 30 inch finishing type: coated, polished material : rubber , steel including withallrelatedaccessories asperhospitalrequirement . 6 hydraulic pump for office wheel chair iron with plastic cover 7 table glass 10 mm completewith molded and finishingas requiredtuffanglass 8 6ft x3ft 9 5ft x3ft 10 4ft x2 ½ ft 11 pvc watering pipe 1” 12 rain coat excel size 13 rubber glove ( for electric work ) 11 k. v. 14 pvc conduct pipe 1” ( isi ) 2mm thick 15 supply of synthetic material ( ptmt ) bib cock of 15 mm nominal bore 86 mm long. 16 supply ofss watertape pushon type½’’size 17 ½’’size brass tape head set 18 brass float ball cock 38 / 40 mm nominal bore 19 brass float ball cock50 mm nominal bore 20 brass float ball cock25 mm nominal bore 21 brass wt. 400 gm, 15 mm nominal bore 22 brass angleheavy valve ½’’ 23 gi elbow 24 15 mm 25 gi socket 26 15mm 27 38 / 40 mm 28 gi hex nipple 29 15 mm 30 gi plug heavy 31 15 mm 32 50mm 33 100 mm 34 g.i. nipple15 mm 35 4” length 36 8” length 37 12” length 38 g.i. nipple25 mm 39 2” length 40 4” length 41 6” length 42 10” length 43 12” length 44 pvc pipe with c.p.brass nuts up to length of 300 mm 45 pvc tank cover with hinges and locking system for following capacity storage tanks. 46 500 ltr. capacity thread type 47 1000 ltr. capacity thread type 48 pvc waterhose / hdpe pipe 1 49 pvc water hose / hdpe pipe1 1 / 2 50 pvc water hose / hdpe pipe 2 51 pvc water hose / hdpe pipe 52 kabja2” stainless steel 53 stainless steelkabja3” 54 almirah lock 55 almirah lock big size 56 almirah lock small size 57 glass bottle 100 ml transparent with iron cap 58 glass bottle 15 ml transparent with iron cap 59 supply of silver coated iron cap suitable for 1.5 / 2 literbisra glass jar. 60 pvc watering pipe ½” 61 weight machine electronic up to 100kg 62 supply ofsynthetic material ( ptmt ) push cock of 15 mm nominal bore. 63 supply of gun metal full way valves 64 15 mm 65 mixture tapheavy duty 66 g.i. pipe b class. 67 15 mm dia nominal bore 68 25 mm dia nominal bore 69 gi elbow 70 25 mm 71 gi tee 72 15 mm 73 25 mm 74 gi socket 75 25 mm 76 gi union 77 15 mm 78 25 mm 79 gi hex nipple 80 25 mm 81 gi plug heavy 82 25 mm 83 g.i. nipple15 mm 84 2” length 85 6” length 86 g.i. reducer 87 25 mm x 15 mm 88 40 mm x 25 mm 89 50 mm x 25 mm 90 c pvc pipe ¾’’ 91 c pvc pipe 1’’ 92 c pvc socket¾’’ 93 c pvc brass tee ¾’’x ½’’ 94 c pvc brass elbow ¾’’x ½’’ 95 c pvc body valve ¾’’ 96 c pvc brass elbow1’’ 97 c pvc brass tee 1’’ 98 c pvc brass union 1’’ 99 c pvc brass socket mt 1’’ 100 c pvc brass socket ft 1’’ 101 c pvc brass socket ¾’’x1” 102 supply of self priming mono blockpum set of approved make, tefc, perment split capacitor ( psc ) , thermonal over olad machnial sheet 1440 / 1500 rpm, single phase , operting voltage 180 to 240 volt 103 0.5h.p., 1 ph 230 v 50 hz ( 6 28 ) mtr, ( 45 7.5 ) lpm 104 1h.p., 1 ph 230 v 50 hz ( 10 50 ) mtr ( 53 6.5 ) lpm 105 2h.p., 1 ph 230 v 50 hz ( 12 60 ) mtr ( 210 130 ) lpm 106 7.5 h.p., 3 ph, 41v, 50hz ( 20 32 ) mtr, ( 1060 900 ) lpm 107 brass valve 1” 108 brass valve 2” 109 brass valve 3” 110 19mm 6x4 111 12 mm 6x4 112 supply of ply 113 6 mm 7x4 114 4mm 8x4 115 pipe wrinch 10 116 pipe wrinch 12 117 pipe wrinch 14 118 pipe wrinch 18 119 pipe wrinch 24 120 cpvc union 1½ 121 cpvc reduser1½x1 122 cpvc socket plain 1½ 123 cpvc elbow 1½ 124 cpvctee 1½x1 125 cpvc teee1½x½ 126 cpvc teee1½x1 1 / 4 127 cpvc valve1½ 128 cpvc vave 2 129 cpvc tee 2x2 130 cpvc tee2x1 131 cpvc socket 2 132 cpvc tee 2 133 cpvc union2 134 cpvc elbow 2 135 cpvc pipe 1½ 136 cpvc pipe2 137 cpvc pipe 1 1 / 4 138 gi data ½ 139 gi data 1 140 gi data 1½ 141 gi data 2 142 gi data 3 143 cement bags50 kg 144 white bags 1 kg 145 flush tank & z connectionplastic 146 pvc pani tankper liter with cover . 147 ot mixure high quality brass 148 iron cutter grander machine 149 c.p. pillor cock long thread. brass 150 c pvc elbow ¾’’ 151 c pvc tee¾’’ 152 c pvc brass tee 1 / 2’’ 153 c pvc brass socket1’’ 154 c pvc brass tee ¾’’x1” 155 c pvc body valve 1” 156 cpvc solvent 100 ml 157 union3” 158 union2” 159 union1” 160 synthetic adhesive for wood 161 brass handle valve½ ’’ 162 l type tape ½ ’’ 163 brass bigcock ½ ’’ 164 rubber wheel 4 inch x 1 inch suitable for above company makeembossing 165 swivel castor 4 ½ inch x 1 ½ inch from center duly fixed with thrust bearing l m and 1 ¼ inch in mandrel size.company makeembossing 166 rubber wheel 4 ½inch x 1 ½ inchsuitable for above item no. 3company makeembossing 167 supply ofsynthetic material ( ptmt ) push cock of 15 mm nominal 168 cpvc socket plain 1 169 cpvc plain elbow 1 170 cpvc reduserplain1½ 171 cpvcunion 3 / 4 172 mapt out chudi in chudi ¾ iron 173 mapt cpvc out chudi in chudi 2 socket + elbow 100 174 cpvc waspesionltype long body tape 175 cpvctape 1 / 2 176 spreaders 160 a fp ( set of 4 pcs ) 177 spreaders 200 a fp ( set of 4 pcs ) 178 spreaders 250 a fp ( set of 4 pcs ) 179 spreaders 400 a fp ( set of 4 pcs ) ...

Department Of Atomic Energy - Rajasthan

37683021 bids are invited for skf and fag make bearings cylindrical roller bearing no. nu321 e , cylindrical roller bearing no. nu320 e , cylindrical roller bearing no. nu324e , deep groove ball bearing no. 6238 m c3 , angular contact ball bearing no. 7332 b , cylindrical roller bearing no. nup 2312 e , taper roller bearing no. 29322 e , taper roller bearing no. 29430 e , cylindrical roller thrust bearing no. 81217 , taper roller bearing no. 31312 xl df a80 120 , taper roller bearing no. 32312 a total quantity : 63...

Rajasthan Rajya Vidhyut Utpadan Nigam Limited - Rajasthan

37682393 requirement of spares for routine, breakdown and annual maintenance of hydro coupling of boiler feed pump ( motor drive ) model r 111 kgs of m / s voith turbo. in unit7&8 ( 2x660mw ) , stps sc, suratgarh fusible plug, seals for hydro coupling, o ring, dp groove ball bearing, bearing shell, thrust bearing, main oil pump set of bearing, guide bush, scoop tube ccw ass., i to h converter voith , connecting cable....

Department Of Atomic Energy - Rajasthan

37623520 bids are invited for bearings 1.ball bearings , 2.ball bearings , 3.ball bearings , 4.ball bearings , 5.ball bearings , 6.cylindrical roller bearings , 7.ball bearings , 8.ball bearings , 9.ball bearings , 10.roller thrust bearings , 11.ball bearings , 12.deep groove ball bearing , 13. cylindrical roller bearing , 14.cylindrical roller bearing , 15.cylindrical roller bearing , 16.tapered roller complete bearing , 17.tapered roller complete bearing total quantity : 196...

Rajasthan Rajya Vidhyut Utpadan Nigam Limited - Rajasthan

37411586 supply of spares of rotork make actuators installed in stage i to iv at stps, suratgarh. complete actuator, limit bswitch 2no + 2nc, drive bush type a, torque switch 2no + 2nc, thrust bearing with washer, thrust base assembly....

Military Engineer Services - Rajasthan

37273691 repair and maint of pump set, starter, crane and its allied works at niwaru, jaipur mil stn under age ( i ) niwaru. 1 taking out submersible pump set of cap 10hp, 3 phase, 415 volts, 50hz ac supply along with column pipe ( appx 90 rm ) from the bore well after disconnecting electric connection, dismentling of pump and motor, repairing / replacing defective parts as ordered and re assembling and testing including replacing worn out nuts, bolts, washers complete and lowering the same after repairing and making electrical and delivery pipe connections complete all as specified and directed for replacement ofu / s parts if anyshall be measured and paid separately as supply only under item nos 1.01 to 1.11 note : ( a ) cost of taking out& fixingshall be deemed to be included in quoted rate of this item. ( b ) taking out and lowering work should be done manually as per site condition. 2 supply only gi column pipe 40 mm bore, medium grade 3 rm / 6rm long with flange, gasket , nut bolts & washers etc complete. 3 supply only gi column pipe 50 mm bore, medium grade 3 rm / 6 rm long with flange, gasket , nut bolts & washers etc complete. 4 supply only gi column pipe 80 mm bore, medium grade 3 rm / 6rm long with flange, gasket , nut bolts & washers etc complete. 5 supply only gun metal / pvc impeller with neck key, distance bush. 6 supply only foot valve cast iron for 10 hp pump 7 supply only shaft bush. 8 supply only thrust bearing with plate of pump ( make : aroma / ksb ) . 9 supply only rubber gasket 3mm thick having 4 nos of 5 / 8” dia hole. 10 supply only shaft coupling with key. 11 supply only jointing kit for submersible cable. 12 supply only steel sleeve for submersible cable. 13 rewinding the stator with super enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles etc.as per relevent is code and pratice. 14 dismantling of centrifugal pump set after disconnecting from power mains & pipe line of capacity 40 hp, 3 phase, 415 volts, 50hz, ac supply & re connect to pipe line & power mains after carrying out repairs if any under item no 3.02 to 3.04complete all as specified and directed. ( note. spare parts required for replacement shall be measured & paid for separately andcost of taking out old & fixing charges for new if any, ordered for item no 3.02 to 3.04shall be deemed to be included in quoted rate of this item. ) 15 transportation of motor tocontractor’s work shop and back to site after repair, cutting of burnt winding & rewinding the stator with super enamelled copper wire of suitable size and class of insulation incl insulation paper, sleeves, thimbles etc complete. 16 supply only, stainless steel pump shaft. 17 supply only, gun metal impeller with neck key, distance bush. 18 supply only ball bearing as per existing no 19 dismantling of centrifugal pump set after disconnecting from power mains & pipe line of capacity 10 to 15 hp, 3 phase, 415 volts, 50hz, ac supply & re connect to pipe line & power mains after carring out repairs if any under item no 3.01 to 3.04 complete all as specified and directed. ( note. spare parts required for replacement shall be measured & paid for separately andcost of taking out old & fixing new if any ordered for item no 3.01 to 3.04shall be deemed to be included in quoted rate of this item. ) 20 transportation of motor tocontractor’s work shop and back to site after repair, cutting of burnt winding & rewinding the stator with super enamelled copper wire of suitable size and class of insulation incl insulation paper, sleeves, thimbles etc. 21 supply only, stainless steel pump shaft. 22 supply only, gun metal impeller with neck key, distance bush. 23 supply only ball bearing as per existing no 24 dismantling of centrifugal / monoblock pump set after disconnecting from power mains & pipe line of capacity 5 to 7.5 hp, 3 phase, 415 volts, 50hz, ac supply & re connect to pipe line & power mains after carring out repairs if any under item no 4.01 to 4.04 complete all as specified and directed. ( note. spare parts required for replacement shall be measured & paid for separately andcost of taking out old & fixing new if any ordered for item no 4.01 to 4.04shall be deemed to be included in quoted rate of this item. ) : 25 transportation of motor tocontractor’s work shop cutting of burnt winding & rewinding the stator with super enamelled copper wire of suitable size and class of insulation incl insulation paper, sleeves, thimbles etc. 26 supply only, stainless steel pump shaft. 27 supply only, gun metal / pvc impeller with neck key, distance bush. 28 supply only ball bearing as per existing no 29 s&f for replacement of submersible cables pvc insulated over all sheathed flat ( isi marked ) of size 6 sqmm, 3 core, 1100 volts gradecomplete all as specified and direced. 30 s&f in repairs metal pump coupling of size 3 dia, suitable for existing pump set. 31 s&f in repairs metal pump coupling of size 4 dia, suitable for existing pump set. 32 s&f in repairs rubber coupling of size 3 dia, suitable for existing pulley set with nut bolts complete 33 s&f in repairs rubber coupling of size 4 dia, suitable for existing pulley set with nut bolts complete 34 supply and fix in repair dol starter, 7.5hp ( mk 2 ) suitable for 7.5 hp 3 phase, 415 volts ac supply motorcomplete all as specified and directed. make: l&t cat part no ss 90947 or equivelent make of havells, c&s, kirloskar, crompton 35 supply and fix in repair dol starter, 10hp ( mu1 ) suitable for10 hp 3 phase, 415 volts ac supply motorcomplete all as specified and directed. make: l&t cat part no ss 95647or equivelent make of havells, c&s, kirloskar, crompton 36 supply and fix in repair star delta starter automatic 3 phase for submersible pump 10hp 3 phase, 415 volts ac supply motorcomplete all as specified and directed. make: schneider ( cat part no ms23a / 16 or as per latest model available for submersible pump ) or equivelent make of havells, c&s, kirloskar, crompton 37 supply and fix in repair of fully automatic star delta starter 15 hp ( mn 16 fasd ) comprising of combo volt andammeter single phase preventor, over load relayand timer housed in ms sheet power coated enclosurecomplete all as specified and directed. make: l&t cat part no ss 94362or equivelent make of havells, c&s, kirloskar, crompton 38 supply and fix in repair of fullyautomatic star delta starter 50 hp ( mn 45 fasd ) comprising of combo volt andammeter single phase preventor, over load relayand timer housed in ms sheet power coated enclosurecapacity complete all as specified and directed. make: l&t cat part no ss 94021or equivelent make of havells, c&s, kirloskar, crompton 39 supply and fix in replacement of mccb of the following sizes complete all as specified and directed. 40 4 pole, 415 v, 16 100 amp., andbreaking capacity of 16 to 18 ka make cat part cm90518 series of l&t or equivalent in legrand / schneider / havells 41 4 pole, 415 v, 125 amp., andbreaking capacity of 16 to 18 ka make cat part cm90677 series of l&t or equivalent in legrand / schneider / havells 42 4 pole, 415 v, 160 amp., andbreaking capacity of 25 ka make cat part cm90634 series of l&t or equivalent in legrand / schneider / havells 43 mccb tp 200 amp, 415 volts, 50 hz 50 ka make havells cat part ihllsebt0200 or equivalent in abb / l&t / schneider / legrand 44 mccb tp 100 amp, 415 volts, 50 hz 35 ka make havells cat part ihlant0100 or equivalent in abb / l&t / schneider / legrand 45 mccb tp 63amp, 415 volts, 50 hz 35 ka make havells cat part ihlant0063 or equivalent in abb / l&t / schneider / legrand 46 m&l for replacement of change over switch 63 amps 415 v , 4 pole front handle type as per site requirementcomplete all as specified and directed.make havells cat part ihcnf series or equivalent in abb / l&t / schneider / legrand 47 m&l for replacement of change over switch 100 amps 415 v , 4 pole front handle type as per site requirementcomplete all as specified and directed.make havells cat part ihcnf series or equivalent in abb / l&t / schneider / legrand 48 m&l for replacement ofu / s 3 pole power contactor type mo of capacity 45 amp complete all as specified and directed.make : l&t ( cs 94570 ) series or equivalent make of havells, c&s, kirloskar, legrand 49 m&l for replacement ofu / s 3 pole power contactor type mo of capacity 32 amp complete all as specified and directed.make : l&t ( cs 94568 ) seriesor equivalent make of havells, c&s, kirloskar, legrand 50 m&l for replacement ofu / s 3 pole power contactor type mo of capacity 18 amp complete all as specified and directed.make : l&t ( cs 94835 ) series or equivalent make of havells, c&s, kirloskar, legrand 51 m&l for replacement of u / s electronic timer for 3 phase 50 hz 3 30 sec or 12 120 sec as per requirement complete all as specified and directed. make : l&t ( st 100 ) seriesor equivalentmake: havells, c&s, standered, indo asian 52 m&l for replacement ofu / s auto switch complete all as specified and directed. make : minilac / gelco or equivalent make as per ps 53 m&l for replacement of u / s micro processored based relay 5amp to 60 amp. make:l&t, havells, hpl, abb 54 m&l for replacement ofu / s single phase preventer relay with settable time on delay 30 sec to 5 min complete all as specified and directed.make : l&t ( xm 818 ) series or equivalent make of havells, c&s, abb, l&t 55 supply & fix in repairs amp meter square type size 9.5 x 9.5cm digital type with ct 03 nos complete of suitable size alll as per required or as directed by eic 56 supply & fix in repairs amp meter square type size 5 x 5cm analog type with ct 03 nos complete of suitable size alll as per required or as directed by eic 57 supply & fix in repairs volt meter square type size 9.5 x 9.5cm digital typecomplete of suitable size alll as per required or as directed by eic 58 supply & fix neon led lamp with cap &lamp fitting complete for r / y / bphase indicator in existing panel. 59 supply & fix selector switchesfor volt meter, amp meter with complete accessories fitted on existing panel. 60 supply calcium based high strength granular chlorination chemical ( aquafit brand calcium hypochlorite having chlorine 65% to 70% ) for water treatment. granular material which is free of foreign material decomposing at 177 c soluble in water and alcohol not hygroscopic practically clear in water solution at saturation level. the material should not contain more than 5% to 10 % moisture. granular size should be as follows: mesh passing through 100 bss 1.5 % maximum iron as fe 0.05% maximum mn 40 ppm maximum mol wt 142.98, toxicity :oral rate ld 50 850 mg / kg. duly tested from approved laboratory packed in a fibre drum duly sealed granulartype frommanufacturer or authorised dealer / distributor complete all as specified and directed.note brand name / batch number and complete particulars of manufacturer should be printed on the container / packing.make: m / s shree rayalaseema hi strength hypo ltd / declibec / potter or equivalent make approvedby e in cs branch, ahq new delhi 61 m&l for regular maintenance of indoor double girder, flame proof eot crane, box type pendent push button operated crane 2.0 ton capacity with span 12000 mm, lift 7500 mm , make hercules mechanical works including regular servicing, inspections, preventive maintenance by replacing minor parts like bearing, fasteners, mcb, contactors, chocks, vfd programming , checking of alignment of pully, proper rope rolling on pully, changing of gear oil, breake oil, overload relay internal wiring of panel by trained technicians. note ( a ) work shall be carried out through reputed service centre of eot crane, frequency of each preventive maintenance should be once in a month at equal interval. ( b ) spare parts required for replacement shall be measured & paid for separately andcost of taking out old & fixing new if any ordered for item no 33 to 35shall be deemed to be included in quoted rate of this item. ( c ) in case of emergency breakdown it should be attended at odd hours also without any extra cost and the rate quoted above shall be deemed to be included.the following parts should be check under maintenance / preventive maintenance. ( a ) hoist speedmeter ( b ) c.t. speed meter ( c ) l.t. meter ( d ) m.h. brake & drum assy ( e ) c.t. brake & drum assy ( f ) l.t. brake & drum assy ( g ) m.h. gear box ( h ) c.t. gear box ( i ) l.t. gear box ( j ) l.t. wheel assy tread dia. ( k ) c.t. wheel assy tread dia. ( l ) m.h. rope drum assy ( m ) m.h. rope dia / falls ( n ) hoist coupling drum ( o ) c.t. coupling ( p ) l.t. coupling ( q ) m.h. limit switch rotary ( r ) gantry girder & rail for bay length ( s ) hook block assy m.h. ( t ) panel complete with lt & ct vvvf drive ( u ) maintenance platform 62 m&l for serving of hoist up / down etc. all type motions of crane of capacity 2.0 ton including minor parts required for makingserviceable all as directed by engr in charge. 63 supply only variable frequency drive with built in plc program with 5000 steps capacity, supports open loop control of permanent motors, new pcb coating for circuit and thermal design suitable for harsh environment applications, suitable for 5 hp, 3 phase supply make delta c200 series ac drives make delta, l&t or equivelent as per ps 64 supply only heavy duty limit switch snap action type nl ip 67suitable for 2.0 ton capacity crane. 65 supply only 19 core, 01 sqmm cable, pvc insulated suitabe for 2.0 ton capacity crane 66 m&l for load testing indoor double girder, flame proof eot crane, box type pendent push button operated crane 2.0 ton capacity with span 12000 mm, lift 7500 mm , make hercules mechanical works in niwaru workshop by hiring load ( rcc cubes ) 2 ton capacity in 4 stages on50%, 75%, 100% and 125% of load capacity including suitable transportand safety measures required for loading and unloading weight all as specified and directed by engr in charge. ( as per is 3177 and 807 ) note ( a ) arrangement of load testing including loads should be providedby contractor the cost ofadditional arrangements required to adhere above said provision shall be deemed to be included in the quoted rates. ( b ) load test report in specific forms duly sign by testing authority to be submitted by contractor....

Department Of Local Bodies - Rajasthan

37172712 supply and fixing of different electric and cables accessories near maheshwari samaj dharmshala, nathdwara. , sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and other parameters required as per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: ( a ) thickness of crca sheet shall be 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel. the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only. all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgear is to be paid extra ) ( d ) wiring between components within switchgear and incoming / outgoing cable shall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. ( f ) floor mounted panel shall be mounted on base frame of ismc channel size 100 x 50 x 5 mm ( to be paid extra ) ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . , supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulator with standard short circuit withstand capacity , high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . electrolytic grade aluminium bus bar 6010 grade , providing & fixing of is: 13875 & iec :61326 confirming led digital type ( up to 500 ) v range volt meter / direct ammeter / ct oertated ammeter / frequency meter / kwh meter / multi function meter / power analyzer of class 1 accuracy as per is : 1248 of size 96mm x 96 mm including making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . three phase ammeter with inbuilt selector switch , providing & fixing of bis approved current transformer as per pwd specification for electrical works , isi marked as per is 2705 1992 / conforming to iec 60044 1, with secondary terminal of ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as required current transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr resin cast wound type ct c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va , providing & fixing of ip 51 ( upto 500 ) v range volt meter on existing panel as per pwd specification for electrical works, making connection by pvc insulated copper conductor with pvc sleeves / channel etc. meter shall give true rms measurments, acc. ci 1.0 or better , with field programmable primary & sec. values pt ( vt ) primary upto 2000 kv. field programmable high and low threshold values, meter shall compliance of is 13875 & iec 61236. as required. oem must have bis certificate and & shall have submit nabl / cpri / erda lab test reports before execution &all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . digital , providing & fixing of 110 / 220 v, unibody led indicating lamp iec 60947 with integral circuit, ip 65 above panel & ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min. 29 mm, contact material phospher bronze for led, pcb contacts shall be of brass ( tin plated ) , impulse dielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdc including connection etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . red / yellow / green colour , blue / white colour , providing & fixing of electrical insulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006 with one side anti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 3.3 kv, class a 2 mm thick with proof voltage 10 kv ac ( rms ) and break down voltage 30 kv ac ( rms ) , sitc of ip 40 4 pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440 / 415 v, 50 hz; o / l & s / c and inst. protection setting , true rms sensing. as per pwd specification for electrical works, conforming to is / iec 60947 p 2 :2003 with front face and centralised adjustable, common fault led indication, thermal memory, release trip shall confirm to emc / emi compatability, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage 800 v, provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections with lugs & spreaders, etc. as required. oem shall have submit nabl / cpri / erda accrediated lab type test certificate before execution & all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 4 pole mccb withwith microprocessor based release 400 amp , 50 ka, adjustable o / l & adjustable s / c setting, ics = 100 % icu , providing & fixing of 240 / 415 v isolator isi marked is:13947 iii / conforming to iec 60947 3, suitable for ac22a utilization category, 4kv impulse withstand voltage, true contact indication, red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. ip 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab type test reports & all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr four pole isolator 100 a rating , supply & fixing of gi pipes confirming to is : 1239 p 1 ( 2004 ) with flanges duly screwed & welded including rubber washer, nuts & bolts of 8mm dia complete in all respect.all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . b class 50 mm dia , p / laying isi marked p.v.c. insulated submersible cable confirming to is:694 with flexible copper conductor including making connection etc. as required 10.0 sq.mm 3 core flat , providing & fixing of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be of carbon + s.s.the stator body of single phase pump shall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 2.0 hp, 1 ø, ( 12 25 ) mtr, ( 350 115 ) lpm , 5.0 hp, 3 ø, ( 14 28 ) mtr, ( 995 500 ) lpm , supply installation testing & commissioning of iso certified company made dol / star delta starter panel made out from 1.6 mm thick powder coated crca sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, illuminated on / off push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. appropriate type test certificate / oem test report shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . for three phase submersible / mono block pump 3.0 hp to 10.0 hp ( star / delta starter ) , providing & fixing in position frame made out of m.s. angle ( riveted or welded ) as per is: 2062 2011 finished with two coats of red oxide and two coats of enamel paint including cutting, welding, holes etc. of following sizes as required. all drawing as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 50mm x 50mm x6mm , providing & fixing of digital time switch having following day / week programme and minimum 100 hours reserve and ac1 rating of 16 20 amperes including making connection, programming conforming to iec 60730 1 and 60730 2 7 etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . one day & week reserve ( mechanical type ) , supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm ) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a or c , flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc / ms conduit / casing capping including all as per pre approved by engineer in charge, making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products / work , refer annexure a attached with this bsr . bsr. 1 x 6.0 sq.mm , providing & fixing of 240 / 415 v isolator as per pwd specification for electrical works with isi marked is:13947 iii / conforming to iec 60947 3, suitable for ac22a utilization catagory, 4kv impulse withstand voltage, true contact indication, red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. , label holding facility , ip 20 contact protection and fitted with existing distribution board / sheet including making connections, testing etc. as required. oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . four pole isolator 63 a rating , providing & fixing of 240 / 415 v ac mcb with positive isolation of breaking capacity not less than 10 ka ( b / c tripping characteristic as per type of load and site requirement ) 4kv impulse withstand voltage, as per pwd specification for electrical works with isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted with existing distribution board / sheets, min. operation 20, 000 upto 32 a rating and 10, 000 upto 63 a, 5000 for 80 a rating including making connections, testing etc. as required. . oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . single pole mcb 6 a to 32 a rating , providing & laying p.v.c. / xlpe insulated & p.v.c. sheathedarmoured aluminium cable of 1.1 kv grade as per pwd specification for electrical works in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points ( a ) , ( b ) , ( c ) , mentioned below: ( a ) material : h4 grade aluminium conductor of purity >99.6 % & as per is:1554 p i / is :7098 p – i ( b ) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999 for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 ( part 0 to 64 ) for testingprocedures. ( c ) oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities for cables . appropriate type test certificate / oem test report shall be submitted . all above as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr. armoured cable 300 sqmm 3.5 core , 35 sq. mm 3.5 core , 25 sqmm 4 core , 16 sq.mm 4 core , 10 sq.mm 4 core , 6 sq.mm 4 core , 6 sq mm 2 core , supplying and making one end termination with heavy duty brass compression gland ( as per is 12943 1990 ) sibg type, heavy duty aluminium lugs ( as per is 8309 1993 & is 8337 1976 ) duly crimped with crimping tool, pvc tape as per pwd specification for electrical works etc for following size of armoured pvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required of size. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . of size 3.5 x 70 sq. mm , of size 3.5 x 35 sq. mm , of size 4 x 10.0 sq.mm , of size 4 x 6.0 sq.mm , of size 4 x 16 sqmm , supplying and making end termination with heavy aluminium lugs pin / ring type ( as per is 8309 1993 & is 8337 1976 ) duly crimped with crimping tool, pvc tape as per pwd specification for electrical works etc of following size. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . size 16.0 sq mm , size 25.0 sq mm , size 35.0 sq mm , size 70.0 sq mm , size 10.0 sq mm , size 6.0 sq mm , dismantling of existing structures like culverts, bridges, retaining walls, cc road and other structure comprising of masonry, cement concrete, wood work, steel work, including t&p and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 50 metres as directed by engineer. cement concrete grade m 15 and above and pcc blocks , providing and laying of double wall corrugated pipe confirming to is :14930 p 1 & 2 with hdpe coupler at 1 mtr. depth below the ground for laying cable including making the trench and back filling, compaction of earth as required ( excavation of earth to be paid extra as required. ) of following outer dia. / inner dia as per is:4984:1994 all as per pre approved by engineer in charge for additional technical parameters of products / work , refer annexure a attached with this bsr . 55 / 50 mm , 90 / 76 mm , supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm ) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a or c , flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc / msconduit / casing capping including all as per pre approved by engineer in charge, making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products / work , refer annexure a attached with this bsr . 2 x 2.5 sq.mm , 2 x 1.5 sq mm , earth work in excavation for roadway, including trimming bottom and side slopes in accordance with requirement of line, grades and cross sections, including disposal of surplus material with all lift and lead upto 1000 metre as per mort&h specification clause 301. in ordinary rock , earth work in excavation for roadway, including trimming bottom and side slopes in accordance with requirement of line, grades and cross sections, including disposal of surplus material with all lift and lead upto 1000 metre as per mort&h specification clause 301. in hard rocks ( blasting prohibited ) , carriage of materials by mechanical transport including loading, unloading and stacking : 3 km , providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering all work upto plinthlevel 1:4:8 ( 1 cement : 4 fine / coarse sand : 8 graded stone aggregate 40 mm nominal size ) . : , providing and laying cement concrete in retaining walls, return walls, walls ( any thickness ) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets etc. upto two stories, excluding the cost of centring, shuttering and finishing : 1:1½:3 ( 1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size ) . , providing & fixing of 240 / 415 v ac mcb with positive isolation of breaking capacity not less than 10 ka ( b / c tripping characteristic as per type of load and site requirement ) 4kv impulse withstand voltage, as per pwd specification for electrical works with isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted with existing distribution board / sheets, min. operation 20, 000 upto 32 a rating and 10, 000 upto 63 a, 5000 for 80 a rating including making connections, testing etc. as required. . oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . single pole mcb 0.5 a to 2 a rating , providing & fixing of iso certified company made 240 / 415 v porcelain kitkat fuse ( / hbc type ) as per pwd specification for electrical works conforming to is:2086, 1983 on existing board / sheet including making connections with lugs, testing etc. as required . appropriate type test certificate / oem test report shall be submitted . all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 63 a , 415 v , providing & fixing of ac operated heavy duty 230 / 440 volt power contactor as per pwd specification for electrical works, isi marked is / iec 60947 4 1 : 2000 having provision of mechanical interlocking, auxilary contacts, din rail mounting type including making connections, testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 4 pole power contactors with following ac 3 rating 63 amp , s&f following sizes ( dia. ) of isi marked medium duty pvc conduit along with accessories in surface / recessed using saddles, clamps, fastener as required including cutting the wall and making good the same as required. 25 mm , s&f following sizes ( dia. ) of isi marked medium duty pvc conduit along with accessories in surface / recessed using saddles, clamps, fastener as required including cutting the wall and making good the same as required. 40 mm , sitc of quick make and quick break 4 pole current limiting mccb having following current rating, short circuit breaking capacity at 440 / 415 v, 50 hz; o / l & s / c settings and conforming to is 13947 2 / iec 60947 2 with front face and centralised adjustable, line load interchangeability, having positive isolation capability, provision for uvr , shunt trip , earth fault trip, push ( test ) to trip , including making connections with lugs / spreaders etc. as required with thermal magnetic release up to 100 amp , 16 / 25 ka, adjustable o / l & fixed s / c setting , p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and enamel paint of following sizes as required. 25mm x 25mm x 5mm , sitc of chemical gel earthing system of dual pipe technology made of with b class g i pipe as per is 1239 ( part 1 ) :2004 of medium duty of following sizes as per points mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : ( a ) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, cpri / erda tested with rms capacity of minimum 35 40 ka for withstanding 1 second . ( b ) to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated lab for low resistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major content as per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts ( c ) heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height 250 to 300 mm. ( d ) testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. ( e ) self certificate for confirming above standards from oem is mandatory. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . with pipe in pipe technology ( outer pipe dia. / inner pipe dia. ) minimum 100 mm dia borewell gi pipe 2000 mm long, 80 / 50 mm, terminal 50mm x 6 mm gi strip , supply & laying following size earth strip in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, jointing shall be done by overlapping and with 2 set of brass ( for cu strip ) / gi ( for gi strip ) nut bolt & spring washer spaced at 50cm making connection etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 25mm x 3mm alum. strip , supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu thimble etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr . 8 swg g.i. ( hot dipped ) wire , providing & fixing of ip54 on front microprocessor based three phase sensing power factor correction relay , iec / en 61000 6 ( 2&4 ) having 3 ct sensing, sensitivity up to 50 milli amp secondary current , self analysing auto c / k setting according to targeted power factor setting, the relay shall have digit display unit for display of real power factor, targeted power factor, lag / lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with rs 485, indication ofswitching on units, auto / manual status, and shall have over load protection, no volt release , having multi parameter like kw, kva, kvar, vthd, ithd, metering facility as required. oem shall have submit nabl / cpri / erda accrediated lab test reports. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr 12 to 14 stage , providing & fixing of self healing ip20 mpp type shunt capacitor ( banks ) as per pwd specification for electrical works, isi marked is:13340 41 / conforming to iec :831 1&2 or iec : 60831 1& 2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( psd ) and shall have dissipation factor less than 0.0025 at 50 hz and total wattage loss less than 0.35 watt per kvar. min over current capacity 1.8 times rated current & peak inrush current min. 250 times of rated current, including making connections, testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work , refer annexure a attached with this bsr heavy duty three phase 525 v, 50 hz cylindrical capacitor ( bank ) ...

Rajasthan Rajya Vidyut Utpadan Nigam Limited - Rajasthan

37061061 procurement of rtd and thermocouples for stage i and ii, ctpp, chhabra , j – type, duplex ungrounded thermocouplewith thermowell(specification as per annexure 1) , thermowell for above thermocouple at sr. no. 01 ( specification as per annexure 1 ) , k – type duplex ungrounded thermocouple with thermowell for ms temp at sh outlet. (specification as per annexure 2) , k – type duplex ungrounded thermocouple with thermowell for aph hot/cold end temp. (specification as per annexure 3) , thermowell for above thermocouple at sr. no. 4 (specification as per annexure 3) , k – type duplex ungrounded thermocouple with thermowell forcrh stm tmp bfr desh l, stm tmp lphs il. (specification as per annexure 4) , thermowell for above thermocouple at sr. no. 6 (specification as per annexure 4) , r – type duplex ungrounded thermocouple with thermowell for fg system temperature measurement at psh ol.(specification as per annexure 5) , pt 100x2, duplex 3 wire rtd with thermowell for gsc to lp ft temp. (specification as per annexure 6) , thermowell for above rtd at sr. no. 9 (specification as per annexure 6) , pt 100x2, duplex 3 wirertd with thermowell for drn cooler to lp flash tank drn tmp (specification as per annexure 7) , thermowell for above rtd at sr. no. 11 (specification as per annexure 7) , pt 100x2, duplex 3 wirertd with thermowell for aph guide bearing temp (specification as per annexure 8) , pt 100 duplex 4 wire mill bearingrtd (specification as per annexure 9) , pt 100x2, duplex 3 wire head less rtd for fd, pa, fan brg temp.(specification as per annexure 10) , pt100x2 duplex 3 wire headless rtd for bfp bp &thrust bearing temp rtd. (specification as per annexure 11) , k – type duplex ungrounded thermocouple with thermowell for fg temp. at fsh o/l (specification as per annexure 12) , k – type duplex ungrounded thermocouple with thermowell for fg temp. at ltsh o/l (specification as per annexure 13) , r – typeduplex ungrounded thermocoupleforfg systemtemperature measurement at rh ol. (specification as per annexure 14) , k – type duplex ungrounded thermocouple with thermowell for fire protection temp. (specification as per annexure 15) , thermowell for fire protection temp. (specification as per annexure 16) , cable for thurst bearing rtd: duplex 3 wire, 5 mtr.long fep/fep insulated ss braided flexible cable with sealpot. temp range: 0 150 °c (specification as per annexure 17) , thermocouple for ip inner casing (specification as per annexure a) , thermocouple forhp exhaust (specification as per annexure b) , thermocouple for lp casing (specification as per annexure c)...

Department Of Atomic Energy - Rajasthan

36902540 bids are invited for rtds for ksb make pcp mse rtd tag no 11, upper thrust bearing rtd , rtd tag no 10 and tag no 12 , upper and lower journal bearing rtd , rtd tag no 13, lower thrust bearing rtd total quantity : 22...

Rajasthan State Road Transport Corporation - Rajasthan

36748235 rsrtc invites the tneder for supply of ball and tapper roller bearing , specifications of ball & tapper roller bearings as:190:81:march:2014, as:322:66:jan:2004 , 2691 2620 0143 / 3125 / 3133 bb455236 fsassy. needle cage bearing , 2691 2620 0142 / 3124 / 3130 bb728040fsassy needle cage bearing , 2691 2630 3104 tapper roller bearing25572 25520, bs iii / 2017 , p4900402 / mub 7307 / jc 8035tail pinion bearing bs ii , 2576 3340 3103tapper roller bearing32308 bs iv / frt hub outer bearing bs iii / 2017 , f0242510 / f0254010 spigot bearing , f0243010 / f0254610 needle roller bearing 1st , f0242710 / f0254910needle roller bearingbb44545fs , f0243110 / f0254710 2691 2620 3106needle rollerbearing 1st bb627040 , f0242410 / f0259310 roller bearing ( nup 309em ) , f0248510 / f0254510 taper rollerbearing ( 2789 2729 ) , p4900202 diff. pinion bearing ( 493 497 ) , f0259210 / jc 8020cyl. roller bearing ips , f0246010tapper bearing ( 567 563 ) , 6201 2rsalternator bearing tc , mb563234ps center bearing eicher ( tx 7240 ) , f0253810clutch release brg.ley. bs iii ( 6212 lu ) , ib001825 needle bearing 3rd ( b60049 ) , ib001824 needle bearing 1st ( b60047 ) , ib001826 needle bearing reverse ( b60048 ) , ib003070pilot bearing m / s eicher midi , if000148 / bb60063needle bearing 4th eicher midi , if000864 / nup307 mnrneedle bearing c / s , if000863 / nup307 mnneedle bearing c / s , id200359 / jc 8022bearing , id200480 / bb60107needle roller bearing 1st , id200456 / bb60109needle roller bearing 2nd , id200349 / b60106needle roller bearing reverse , 2691 2620 3103 / tapper roller bearing 28580 / 521 bs iii / 2017 / 2013 , 2516 2635 3104roller ring ( rev idler gear ) , id200457bearing 3rd speed , id200458bearing 4th speed , id200453bearing drive pinion , 2691 2625 3113roller thrust bearing arrgmtbs iii / 2017 , f0267310bearing 6.s.850 , f0267510bearing 6.s.850 , f0267410n.r. bearing , f0256310 nr bearing 5th6.s. 850 , f0267710input shaft bearing , 2060 3501 3001tapper rollerbearing 31312l bs iii / 2017 , 2573 3530 3101 / 47487 / 20diff.cage bearing , 2691 2620 3111needle cage bearing ist , jc 409025pinion bearing lay , pop00150pilot bearing r160 crb , hk4012 ntnbearing leyland , 0009811201 / nu309ncyl. roller bearing , 2505 2620 3106four point ball bearing qj309 , 2505 2620 3123double row needle cage bearing , 2505 2620 3124double row roller cage bearing , 2505 2630 3104t.r. bearing bs1 / 2 / 3 / 4 , 6202bearing , 6204bearing , db142012pn.r. bearing...

Medical Health And Family Welfare - Rajasthan

36433514 electrical work in the construction of phc building at badka ( laxmangarh ) distt. alwar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 medium point ( up to 6 mtr. ) 8 long point ( up to 10 mtr. ) 9 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 10 on board 11 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 12 20 mm 13 25 mm 14 32 mm 15 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 16 1 x 1.5 sq.mm 17 3x 1.5 sq.mm 18 2 x 2.5 sq. mm. + 1x1.5sqmm 19 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 20 4 x 10.0 sq.mm 21 4 x 6.0 sq.mm 22 1 x 4.0 sq.mm 23 1 x 2.5 sq.mm 24 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. 25 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 26 2 pair 27 p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.for additional technical parameters of product / work refer annexure a attached with this bsr 28 40mm x 40mm x 5mm 29 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 30 6.4 mm thick 31 p & f phenolic laminated sheet 2.0 mm thick of following size . including screws, cup washer as required.for additional technical parameters of product / work refer annexure a attached with this bsr 32 75 mm dia 33 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 34 single pole mcb ( with b / c curve tripping characteristics ) 35 6 a to 32 a rating 36 double pole mcb ( with b / c curve tripping characteristics ) 37 6 a to 32 a rating 38 four pole mcb ( with b / c curve tripping characteristics ) 39 6 a to 32 a rating 40 50 / 63 a rating 41 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 42 metal door ( single phase ) ik 09 and ip 43 with metal end box 43 16 way ( 16+2 ) 44 metal door ( three phase ) ik 09 and ip 43with metal end box 45 6 way 46 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 47 20 amp, 3 pin + scrapping earth, 4 module 48 p & f of industrial plug and socket conforming to iec 60309 1 / 2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. for additional technical parameters of product / work refer annexure a attached with this bsr 49 ip 67 panel mounted socket 50 32 a 3 pin ( 2p+e ) 51 providing & fixing of flush typenon modular single line telephone jackmade out fromindustrial grade polycarbonate or fire resistant abs material, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 52 providing & fixing of ding dong / musical chime bell as per pwd specification for electrical works, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 54 5 step fan regulator 2 module 360 dgree rotating 55 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 56 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 57 10 pairs 58 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 59 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 60 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 61 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 62 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 63 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 64 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 65 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 66 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 67 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 68 electrolytic grade aluminium bus bar 6010 grade 69 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 70 ring type tape wound ct 71 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 72 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 73 red / yellow / green colour 74 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 3.3 kv, class a 2 mm thick with proof voltage 10 kv ac ( rms ) and break down voltage 30 kv ac ( rms ) 76 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 77 4 pole mccb with thermal magnetic release 78 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 79 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 80 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 open execution type 82 160 a 83 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 84 10.0 sq. mm 85 2 core 86 35.0 sq. mm 87 3.5 core 88 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 89 3.5 x 35.0 sq.mm 90 supplying and makingend termination with heavy aluminiumlugs ( pin / ring type ) confirming to is 8309 1993 & is 8337 1976 duly crimped with crimping tool, pvc tape etc of following size.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 91 35.0 sq.mm 92 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 93 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 94 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 95 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 96 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 97 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 98 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 17.2 mm thick and 3 mtr. long 100 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 8 swg copper wire 102 8 swg g.i. ( hot dipped ) wire 103 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 up to 457 mm size 105 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 106 1200 mm sweep bee 2 star rated ( service value >=4.5 to < 5 ) 107 1200 mm sweep bee 3 star rated ( service value >=5.0 to< 5.5 ) 108 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 109 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 110 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 111 225 mm sweep 112 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 113 300 mm sweep ( 900 / 1400 rpm ) 114 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 450 mm sweep wall mounting and three speed regulator with minimum air delivery 150 cum. / minute 116 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 up to 380 mm size 118 providing & fixing of vertical ( bee 5 star rated ) / horizontal ( bee 3 star rated ) storage water heater with outer casing made of engineering plastic sheet ( upto 25 ltr ) / metal rust proof body ( 35 & 50 ltr ) , glass line / titanium enamel coated pressure pump compatible 8 bar pressure inner tank, glass line coated , mineral filled heating element, stem type, snap actionadjustable thermostat , dual indicating lampsinjected puf insulation, multi function valve etc. as required held in position with 2 / 4 no. 10 / 12 mm anchor fastener, duly wired with 3 core 2.5 / 4.0 sqmm pvc insulated & sheathed copper conductor and 16 a / 25a three pin plug top with portable residual current device ( prcd ) , including making inlet, outlet flexible alloyconnection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 119 15 ltr. 120 sitc ofmnre approved & confirming to is:12933 p 1, 2, 3 & 5 flat plate collector type solar hot water system havingcollector withzincalum sheet outer body , glass line / titanium enamel coated inner tank with metal rust proof puf insulated body includingelectrical back up, thermostat, powder coated / hot dipped galvanized ms standfor collector & tank etc. as required. of following capacity complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 121 200 litre / day 122 providing & fixing of energy efficient direct fit ( retrofit ) polycarbonate / glasshousingsmd mid power led tube rod ( with integral driver & alumn. heat sink ) , on existing fixture.system lumen efficacy = 100 lm / watt output, internal surge protection of 2.5 kv , thd < 20% , p.f.=0.95, cri >80 , life time of minimum35000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 123 1200mm , min. lumens output 2000 lmled tube rod with polycarbonate housing 124 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 125 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 126 surface mounting ( with extruded alumn. housing ) 127 minimum lumen output 1950 lm 128 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 129 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 130 recessed mounting 131 minimum lumen output 4200 lm 132 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 led street light fixture with minimum lumen output 2450 lm 134 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 135 25 mm dia. 136 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 138 cat 6, un sheilded information outlet 139 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 single aperture 141 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 142 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 143 1 mtr 144 supply, installation, & testing of 19 1u rack mounted / surface mounted aluminum / crca 1.2mm powder coated, multimode glass fiber optic cable patch panel / liu loaded with flangless / screwable adapters for st / e 2000 / sc / lc / mt rj / pc type, it should have easy removable top plate with push buttons, there should be a splice tray installed in the patch panel / liu which can handle the fiber cores, splice tray should be pc+abs material, it should include accessories like mounting hardware, gormetts, heat shrink tubes / sleevs, screws, nuts to install the panel for rack / wallmount applications as per requirement complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 multi mode liu 12 ports 146 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 6 u rack with width 600 mm &depth 400 mm + 100 mm 148 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 149 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 1.0 hp, 1 ø, ( 7 12 ) mtr, ( 405 240 ) lpm 151 sitc of monoblock motor pump set isi marked ( is:9079 2002 ) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single / three phase ( 240 440 v ) permanent split capacitor type ( psc ) , fitted with thermal overload protection, including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 1.0 hp, 1 ø, ( 10 120 ) mtr, ( 30 12 ) lpm 153 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 154 1.5 tr iseer not less then 3.8 155 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 156 25 mm 157 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 4 kva 159 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 160 150 mm dia per running inch length 161 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 162 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 163 4 kg...

Medical Health And Family Welfare - Rajasthan

36432928 electrical work in the construction of phc building at duhar chougan ( thanagazi ) distt. alwar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 medium point ( up to 6 mtr. ) 8 long point ( up to 10 mtr. ) 9 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 10 on board 11 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 12 20 mm 13 25 mm 14 32 mm 15 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 16 1 x 1.5 sq.mm 17 3x 1.5 sq.mm 18 2 x 2.5 sq. mm. + 1x1.5sqmm 19 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 20 4 x 10.0 sq.mm 21 4 x 6.0 sq.mm 22 1 x 4.0 sq.mm 23 1 x 2.5 sq.mm 24 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. 25 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 26 2 pair 27 p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.for additional technical parameters of product / work refer annexure a attached with this bsr 28 40mm x 40mm x 5mm 29 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 30 6.4 mm thick 31 p & f phenolic laminated sheet 2.0 mm thick of following size . including screws, cup washer as required.for additional technical parameters of product / work refer annexure a attached with this bsr 32 75 mm dia 33 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 34 single pole mcb ( with b / c curve tripping characteristics ) 35 6 a to 32 a rating 36 double pole mcb ( with b / c curve tripping characteristics ) 37 6 a to 32 a rating 38 four pole mcb ( with b / c curve tripping characteristics ) 39 6 a to 32 a rating 40 50 / 63 a rating 41 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 42 metal door ( single phase ) ik 09 and ip 43 with metal end box 43 16 way ( 16+2 ) 44 metal door ( three phase ) ik 09 and ip 43with metal end box 45 6 way 46 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 47 20 amp, 3 pin + scrapping earth, 4 module 48 p & f of industrial plug and socket conforming to iec 60309 1 / 2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. for additional technical parameters of product / work refer annexure a attached with this bsr 49 ip 67 panel mounted socket 50 32 a 3 pin ( 2p+e ) 51 providing & fixing of flush typenon modular single line telephone jackmade out fromindustrial grade polycarbonate or fire resistant abs material, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 52 providing & fixing of ding dong / musical chime bell as per pwd specification for electrical works, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 54 5 step fan regulator 2 module 360 dgree rotating 55 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 56 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 57 10 pairs 58 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 59 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 60 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 61 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 62 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 63 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 64 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 65 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 66 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 67 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 68 electrolytic grade aluminium bus bar 6010 grade 69 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 70 ring type tape wound ct 71 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 72 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 73 red / yellow / green colour 74 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 3.3 kv, class a 2 mm thick with proof voltage 10 kv ac ( rms ) and break down voltage 30 kv ac ( rms ) 76 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 77 4 pole mccb with thermal magnetic release 78 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 79 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 80 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 open execution type 82 160 a 83 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 84 10.0 sq. mm 85 2 core 86 35.0 sq. mm 87 3.5 core 88 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 89 3.5 x 35.0 sq.mm 90 supplying and makingend termination with heavy aluminiumlugs ( pin / ring type ) confirming to is 8309 1993 & is 8337 1976 duly crimped with crimping tool, pvc tape etc of following size.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 91 35.0 sq.mm 92 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 93 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 94 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 95 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 96 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 97 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 98 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 17.2 mm thick and 3 mtr. long 100 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 8 swg copper wire 102 8 swg g.i. ( hot dipped ) wire 103 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 up to 457 mm size 105 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 106 1200 mm sweep bee 2 star rated ( service value >=4.5 to < 5 ) 107 1200 mm sweep bee 3 star rated ( service value >=5.0 to< 5.5 ) 108 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 109 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 110 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 111 225 mm sweep 112 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 113 300 mm sweep ( 900 / 1400 rpm ) 114 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 450 mm sweep wall mounting and three speed regulator with minimum air delivery 150 cum. / minute 116 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 up to 380 mm size 118 providing & fixing of vertical ( bee 5 star rated ) / horizontal ( bee 3 star rated ) storage water heater with outer casing made of engineering plastic sheet ( upto 25 ltr ) / metal rust proof body ( 35 & 50 ltr ) , glass line / titanium enamel coated pressure pump compatible 8 bar pressure inner tank, glass line coated , mineral filled heating element, stem type, snap actionadjustable thermostat , dual indicating lampsinjected puf insulation, multi function valve etc. as required held in position with 2 / 4 no. 10 / 12 mm anchor fastener, duly wired with 3 core 2.5 / 4.0 sqmm pvc insulated & sheathed copper conductor and 16 a / 25a three pin plug top with portable residual current device ( prcd ) , including making inlet, outlet flexible alloyconnection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 119 15 ltr. 120 sitc ofmnre approved & confirming to is:12933 p 1, 2, 3 & 5 flat plate collector type solar hot water system havingcollector withzincalum sheet outer body , glass line / titanium enamel coated inner tank with metal rust proof puf insulated body includingelectrical back up, thermostat, powder coated / hot dipped galvanized ms standfor collector & tank etc. as required. of following capacity complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 121 200 litre / day 122 providing & fixing of energy efficient direct fit ( retrofit ) polycarbonate / glasshousingsmd mid power led tube rod ( with integral driver & alumn. heat sink ) , on existing fixture.system lumen efficacy = 100 lm / watt output, internal surge protection of 2.5 kv , thd < 20% , p.f.=0.95, cri >80 , life time of minimum35000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 123 1200mm , min. lumens output 2000 lmled tube rod with polycarbonate housing 124 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 125 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 126 surface mounting ( with extruded alumn. housing ) 127 minimum lumen output 1950 lm 128 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 129 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 130 recessed mounting 131 minimum lumen output 4200 lm 132 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 led street light fixture with minimum lumen output 2450 lm 134 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 135 25 mm dia. 136 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 138 cat 6, un sheilded information outlet 139 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 single aperture 141 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 142 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 143 1 mtr 144 supply, installation, & testing of 19 1u rack mounted / surface mounted aluminum / crca 1.2mm powder coated, multimode glass fiber optic cable patch panel / liu loaded with flangless / screwable adapters for st / e 2000 / sc / lc / mt rj / pc type, it should have easy removable top plate with push buttons, there should be a splice tray installed in the patch panel / liu which can handle the fiber cores, splice tray should be pc+abs material, it should include accessories like mounting hardware, gormetts, heat shrink tubes / sleevs, screws, nuts to install the panel for rack / wallmount applications as per requirement complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 multi mode liu 12 ports 146 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 6 u rack with width 600 mm &depth 400 mm + 100 mm 148 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 149 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 1.0 hp, 1 ø, ( 7 12 ) mtr, ( 405 240 ) lpm 151 sitc of monoblock motor pump set isi marked ( is:9079 2002 ) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single / three phase ( 240 440 v ) permanent split capacitor type ( psc ) , fitted with thermal overload protection, including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 1.0 hp, 1 ø, ( 10 120 ) mtr, ( 30 12 ) lpm 153 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 154 1.5 tr iseer not less then 3.8 155 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 156 25 mm 157 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 4 kva 159 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 160 150 mm dia per running inch length 161 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 162 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 163 4 kg...

Medical Health And Family Welfare - Rajasthan

36432910 tender for electrical work in the construction of phc building at basai jogiyan ( thangagazi ) distt. alwar wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 medium point ( up to 6 mtr. ) 8 long point ( up to 10 mtr. ) 9 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 10 on board 11 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 12 20 mm 13 25 mm 14 32 mm 15 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 16 1 x 1.5 sq.mm 17 3x 1.5 sq.mm 18 2 x 2.5 sq. mm. + 1x1.5sqmm 19 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 20 4 x 10.0 sq.mm 21 4 x 6.0 sq.mm 22 1 x 4.0 sq.mm 23 1 x 2.5 sq.mm 24 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. 25 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 26 2 pair 27 p & f in position frame made out of m.s. angle ( riveted or welded ) finished with two coats of red oxide and two coats enamel paint including cutting, welding, holes etc.of following sizes as required.for additional technical parameters of product / work refer annexure a attached with this bsr 28 40mm x 40mm x 5mm 29 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 30 6.4 mm thick 31 p & f phenolic laminated sheet 2.0 mm thick of following size . including screws, cup washer as required.for additional technical parameters of product / work refer annexure a attached with this bsr 32 75 mm dia 33 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 34 single pole mcb ( with b / c curve tripping characteristics ) 35 6 a to 32 a rating 36 double pole mcb ( with b / c curve tripping characteristics ) 37 6 a to 32 a rating 38 four pole mcb ( with b / c curve tripping characteristics ) 39 6 a to 32 a rating 40 50 / 63 a rating 41 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 42 metal door ( single phase ) ik 09 and ip 43 with metal end box 43 16 way ( 16+2 ) 44 metal door ( three phase ) ik 09 and ip 43with metal end box 45 6 way 46 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 47 20 amp, 3 pin + scrapping earth, 4 module 48 p & f of industrial plug and socket conforming to iec 60309 1 / 2 made out of self extinguishing engineering polymer / polyamide, nickel plated brass sleeve and pins, socket with shutter including making connection etc as reqd. for additional technical parameters of product / work refer annexure a attached with this bsr 49 ip 67 panel mounted socket 50 32 a 3 pin ( 2p+e ) 51 providing & fixing of flush typenon modular single line telephone jackmade out fromindustrial grade polycarbonate or fire resistant abs material, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 52 providing & fixing of ding dong / musical chime bell as per pwd specification for electrical works, including making connection testing etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 53 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 54 5 step fan regulator 2 module 360 dgree rotating 55 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 56 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 57 10 pairs 58 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 59 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 60 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 61 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 62 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 63 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 64 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 65 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 66 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 67 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 68 electrolytic grade aluminium bus bar 6010 grade 69 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 70 ring type tape wound ct 71 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 72 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 73 red / yellow / green colour 74 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 3.3 kv, class a 2 mm thick with proof voltage 10 kv ac ( rms ) and break down voltage 30 kv ac ( rms ) 76 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 77 4 pole mccb with thermal magnetic release 78 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 79 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 80 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 open execution type 82 160 a 83 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 84 10.0 sq. mm 85 2 core 86 35.0 sq. mm 87 3.5 core 88 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 89 3.5 x 35.0 sq.mm 90 supplying and makingend termination with heavy aluminiumlugs ( pin / ring type ) confirming to is 8309 1993 & is 8337 1976 duly crimped with crimping tool, pvc tape etc of following size.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 91 35.0 sq.mm 92 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 93 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 94 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 95 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 96 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 97 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 98 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 17.2 mm thick and 3 mtr. long 100 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 8 swg copper wire 102 8 swg g.i. ( hot dipped ) wire 103 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 up to 457 mm size 105 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 106 1200 mm sweep bee 2 star rated ( service value >=4.5 to < 5 ) 107 1200 mm sweep bee 3 star rated ( service value >=5.0 to< 5.5 ) 108 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 109 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 110 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 111 225 mm sweep 112 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 113 300 mm sweep ( 900 / 1400 rpm ) 114 providing & fixing of wall mounting / pedestal type heavy duty air circulator , double ball bearing and with metal sturdy mesh guard; aluminium alloy one piece blade and conforming to is:2997, including fixing with anchor bolts, making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 450 mm sweep wall mounting and three speed regulator with minimum air delivery 150 cum. / minute 116 p & f of gravity louver shutter of superior quality made out of frame of18 swg m.s. sheet & louvers made from 24 swg ms sheetwith enamel paint including cost of nuts, bolts, etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 up to 380 mm size 118 providing & fixing of vertical ( bee 5 star rated ) / horizontal ( bee 3 star rated ) storage water heater with outer casing made of engineering plastic sheet ( upto 25 ltr ) / metal rust proof body ( 35 & 50 ltr ) , glass line / titanium enamel coated pressure pump compatible 8 bar pressure inner tank, glass line coated , mineral filled heating element, stem type, snap actionadjustable thermostat , dual indicating lampsinjected puf insulation, multi function valve etc. as required held in position with 2 / 4 no. 10 / 12 mm anchor fastener, duly wired with 3 core 2.5 / 4.0 sqmm pvc insulated & sheathed copper conductor and 16 a / 25a three pin plug top with portable residual current device ( prcd ) , including making inlet, outlet flexible alloyconnection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 119 15 ltr. 120 sitc ofmnre approved & confirming to is:12933 p 1, 2, 3 & 5 flat plate collector type solar hot water system havingcollector withzincalum sheet outer body , glass line / titanium enamel coated inner tank with metal rust proof puf insulated body includingelectrical back up, thermostat, powder coated / hot dipped galvanized ms standfor collector & tank etc. as required. of following capacity complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 121 200 litre / day 122 providing & fixing of energy efficient direct fit ( retrofit ) polycarbonate / glasshousingsmd mid power led tube rod ( with integral driver & alumn. heat sink ) , on existing fixture.system lumen efficacy = 100 lm / watt output, internal surge protection of 2.5 kv , thd < 20% , p.f.=0.95, cri >80 , life time of minimum35000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 123 1200mm , min. lumens output 2000 lmled tube rod with polycarbonate housing 124 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 125 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 126 surface mounting ( with extruded alumn. housing ) 127 minimum lumen output 1950 lm 128 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 129 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 130 recessed mounting 131 minimum lumen output 4200 lm 132 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 led street light fixture with minimum lumen output 2450 lm 134 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 135 25 mm dia. 136 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 138 cat 6, un sheilded information outlet 139 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 single aperture 141 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 142 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 143 1 mtr 144 supply, installation, & testing of 19 1u rack mounted / surface mounted aluminum / crca 1.2mm powder coated, multimode glass fiber optic cable patch panel / liu loaded with flangless / screwable adapters for st / e 2000 / sc / lc / mt rj / pc type, it should have easy removable top plate with push buttons, there should be a splice tray installed in the patch panel / liu which can handle the fiber cores, splice tray should be pc+abs material, it should include accessories like mounting hardware, gormetts, heat shrink tubes / sleevs, screws, nuts to install the panel for rack / wallmount applications as per requirement complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 multi mode liu 12 ports 146 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 6 u rack with width 600 mm &depth 400 mm + 100 mm 148 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 149 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 1.0 hp, 1 ø, ( 7 12 ) mtr, ( 405 240 ) lpm 151 sitc of monoblock motor pump set isi marked ( is:9079 2002 ) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single / three phase ( 240 440 v ) permanent split capacitor type ( psc ) , fitted with thermal overload protection, including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 1.0 hp, 1 ø, ( 10 120 ) mtr, ( 30 12 ) lpm 153 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 154 1.5 tr iseer not less then 3.8 155 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 156 25 mm 157 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 4 kva 159 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 160 150 mm dia per running inch length 161 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 162 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr ....

Rajasthan State Road Development And Construction Corporation Limited - Rajasthan

36350189 tender for electrification work of iti building at arain district ajmer wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 long point ( up to 10 mtr. ) 8 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 9 on board 10 short point ( up to 3 mtr. ) 11 medium point ( up to 6 mtr. ) 12 long point ( up to 10 mtr. ) 13 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 14 20 mm 15 25 mm 16 32 mm 17 40 mm 18 50 mm 19 s&f following sizesof isi marked ( is:14927 p ii ) virgin materialupvc trunking along with accessorieslike coupler, inner, outer, elbow, square box, tee, end cap etc. on surfacewithscrews, expansionfastenersas required. for additional technical parameters of product / work refer annexure a attached with this bsr 20 100 mm x 50 mm 21 150 mm x 50 mm 22 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 23 1 x 1.5 sq.mm 24 2 x 1.5 sq.mm 25 3x 1.5 sq.mm 26 1x 2.5 sq.mm 27 2 x 2.5 sq. mm. + 1x1.5sqmm 28 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 29 2 x 6.0 sq. mm. + 1 x 4.0 sq. mm. 30 2 x 6.0 sq.mm 31 2 x 4.0 sq.mm 32 4 x 10.0 sq.mm 33 4 x 16.0 sq.mm 34 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 35 2 pair 36 supply and laying of pe insulated jelly filledarmouredtelephone cable. with 0.6 mm thick solid annealed bare copper conductor and confirming to tec specificationsconfirming. to dot gr / cug 01 / aug.2003 in existing pipe / open trench / cable tray / on surface including making necessary connection, testing etc. as required of size. for additional technical parameters of product / work refer annexure a attached with this bsr 37 10 pair 38 50 pair 39 supplying and drawing coaxial cable 75 ohm impedance with foam pe insulated solid bare copper inner conductor, and ist outer conductor of bonded alum. tape and second outer conductor ofalum. alloy braidin existingsurface or recessed conduit / casing capping including making connections as required. for additional technical parameters of product / work refer annexure a attached with this bsr 40 rg 6 41 p / laying isi marked p.v.c. insulated submersible cable confirming to ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen freefor less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, existing pipe / open trench / cable tray / on surface including making connection etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 42 2.5 sq.mm 3 core flat / round 43 4.0 sq.mm 3 core flat / round 44 6.0 sq.mm 3 core flat / round 45 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 46 3.0 mm thick 47 4.8 mm thick 48 6.4 mm thick 49 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 50 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 51 10 pairs 52 50 pairs 53 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 54 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 55 20 amp, 3 pin + scrapping earth, 4 module 56 32 amp, 5 pin + scrapping earth, 8 module 57 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 58 up to 457 mm size 59 providing & fixing ofextra down rod of 15 mm dia . erw ( electrical resistance welded ) of 1.6mm nominal thick medium duty steelpipe including cutting, threading, drilling, fixing quarter pin etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 60 providing & fixing of single / multi tone electronic call bell as per pwd specification for electrical works, including making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 61 providing & fixing of modular type switch / bell push duly isi marked ( is :3854 ) with cm / l no. printed and made out of unbreakable and fire retardant vergin uv stabilized polycarbonatewith brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , minimum width ofswitch toggle ( push part ) should not less then 20mm, includingall as per pre approved by engineer in charge, making connections, testing etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 62 10 a one way switch 63 32 amp. 2 moduleswitch with ledindicator 64 providing & fixing of modular type lockable feature socket dulymade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 65 6 a3 / 5 pin shuttered socket 66 25 amp. 2 module socket 67 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 68 5 step fan regulator 2 module 360 dgree rotating 69 providing & fixing of following modular accessories as per pwd specification for electrical works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 70 t.v. coaxial socket 71 rj 11 telephone jack double line 72 blanking plate 73 modular mcb 6 a to 32 adp 74 providing & fixing offollowing size mounting grid plates with cover plates made from fire retardent uv established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 1 / 2 module 76 8 module 77 providing & fixing ofwiring accessories oem fabricated following size gi box of 1.2 mm thick with earthing terminal and adjustable floating clamp in recess / surface suitable for modular accessories as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 78 1 2 module 79 6 / 8 module 80 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminiumhousing with in built driver, system lumen efficacy = 110 lm / watt output, internal surge protection of 2.5 kv with short & open circuit protection , thd < 10% , p. f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 1170mm ( + / 10% ) led batten with min. lumen output 2200 lm 82 570mm ( + / 10% ) batten with min. lumen output 1000 lm 83 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 84 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 85 surface mounting ( with extruded alumn. housing ) 86 minimum lumen output 1300 lm 87 minimum lumen output 1950 lm 88 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 89 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 90 surface moutning 91 minimum lumen output 4200 lm 92 providing & fixing of ip65 ik08 rated integrated smd mid power led bulk head type light fixture made from pressure die cast al housing suitable with integral driver, system lumen efficacy =100 lm / watt output , thd < 10% , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. surge protection 4 kv. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 93 minimum lumen output 1000 lm 94 providing & fixing of 400 mm sweepbldc technology oscillating type wall mounting / pedestal typefans with three speed, on andoff position, double wall bearing withfront and back 120 or moreribs guard; three no.blades, noise level should be <= 75 db, including fixing with anchor bolts, making connection testing etc. as required. ( with remote ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 95 wall mounting type with service value 2.0 cmm / w, min. air delivery 71 cmm 96 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 97 1200 mm sweep bee 1 star rated ( service value >=4.0 to < 4.5 ) 98 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 300 mm sweep 100 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 300 mm sweep ( 900 / 1400 rpm ) 102 380 mm sweep ( 900 / 1400 rpm ) 103 providing & fixing ofof ventilating fans capacitor start, copper wounded, single phase with pvc impeller, abs body, automatic openable louver shutter in existing opening including making connection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 150 mm sweep 105 250 mm sweep 106 p & f of wall cowl with bird screen suitable for outside wall of exhaust fan openingof following size and made out from 24 swg gi sheet as per instructions of engineer in chargeincluding fixing with suitable fasteners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 107 suitable for 300 mm sweep exhaust fan 108 suitable for 380 mm sweep exhaust fan 109 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 110 led street light fixture with minimum lumen output 11225 lm 111 supply and erection ofgalvanized iron pole with galvanizing done in single dipping ( average coating thickness minimum 65 microns ) continuously tapered poles having octagonal / circular cross sections designed to withstand the maximum wind speed as per is 875, the pole shaft shall be made from sheet steel ( ht steel conforming to grade s355jo ) and confirming to bsen 10025 and shall be continuously tapered with single longitudinal welding. there shall not be any circumferential welding. the welding of pole shaft shall be done by submerged arc welding ( saw ) process. pole shafts shall be provided with the rigid flange plate of suitable thickness ( fe 410 conforming to is 226 / is 2062 ) with provision for fixing 4 no. foundation bolts, this base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside.the octagonal poles shall have lockable door of approximate 500 mm length at the elevation of 500 mm from the base plate with bakelite sheet having 6a sp mcb and 16 sqmm stud type connector ( 4 nos ) inside the pole at door opening for cable connection of following length and dimension as per table p 01 with base plate and foundation bolt on the existing cement concrete foundation.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 112 poles with octagonal cross section 113 7 mtr. 114 supply and fixing of pole oem fabricated hot dipped galvanised m.s. overhang ( 48.3 x 3.25 mm ) with cap ( 400 x 88.9 / 114.3 x 3.25 mm ) over the existing poles. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 single arm overhang 116 providing and laying rcc foundation for octagonal / conical street light poles, high mast poles as per drawing attach at tablep 4with following procedure& all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 a ) excavation of pit for foundation size upto required depth from ground level 118 b ) dressing of pit and dry stone pitching 200 mm thick including supply of stones and preparing surface complete. 119 c ) providing and laying in position cement concrete of m 10 grade of 75 mm thickness 120 d ) reinforcement for r.c.c. work with tmt bars including straightening, cutting, bending, placing in position and binding all complete. 121 e ) centring and shuttering including strutting , propping etc. and removal of form work for footing and pedestal 122 f ) providing & fixing of 2 no. required sizeplb hdpe pipe& foundation bolt with template as per oem recommendations. 123 g ) providing and layingreinforce cement concrete of m 25 grade in footing and pedestal including curing the foundation for 7 days. 124 h ) providing and fixing nosing angle 40 mm x 40 mm x 6mm with 2 no. 100 mm long, 10 mm dia. lugs on each face. 125 pole foundation for octagonal pole from 7 mtr. to 9 mtr. 126 providing & fixing of ik08ip65 protected top / bottom mounted led post top luminarie made of single piece constructionpowder coated die cast alluminium housing with uv stabalized clear / frosted polycarbonate diffuser andaluminium anodised with sand blast reflector. the system level luminous efficacy =100 lumen / w. smd leds is to be used, system cri>70, cct: 3000 / 4000 / 6500 k. the integral electronic driver must be potted & has a unique bis r number must be potted & has a unique bis r number constant current and internal / external surge protection device of min. 4kv ( l n ) and efficiency > 85%, pf>0.9, thd<10% and input voltage range of 140 270v ac at 50hz. system life of 50000 burning hours with 70% of initial lumens maintained . driver current <750ma.fixture must be in compliance with bis standards and trade mark certificate complete in all respect.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 127 minimum lumen output 4500 lm post top luminarie 128 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 129 40 mm dia. 130 supply , installation, testing and comissioning of is:1475 marked self contained drinking water cooler withhermeticallysealed compressor, non cfc refrigerent suitable for operation on 230v / 1ph / 50hz ac supply, full stainless steel ( ss304 ) body ( 0.8 mm thick ) and tank ( 0.5 mm thick ) , stainless steel water tray, minimum two nosbrass chrome plated faucets and suitable drainage system complete in all respect with requiredheight ms fabricated and painted angle iron frame ( cost of frame to be paid extra ) complete in all respect of the following capacity.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 131 cooling capacity 150 ltr. / hr. and storage capacity 150 ltrs 132 providing and laying non pressure np 3 classr.c.c. pipes including collars / spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) etc. as required. ( excavation of earth& back filling with compaction is to be paid extra ) . all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 200 mm dia. 134 labour charges for excavating trenches of required width for pipes dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 mtr.: 135 all kind of soils 136 sitc of wall type following zone ( each zoneaccessing minimum 20 units ( detectors / devices ) ) conventional type microprocessor based with lcd display en / lpcb / ul listed / approved main control panel fabricated from 16 swg crca sheet steel sealed maintenance free ( smf ) batteries of min2x7ah of 12 v or as required.including the cost of all accessories, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 4 zone 138 sitcof en / lpcb / ul listed / approved conventional type manual call point resettable complete with glass, hammer and chain etc.including the cost of all accessories etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 139 sitc of en / lpcb / ul listed / approved conventional type hooter cum strobe including the cost of all accessories, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 supply & fixing of water + afff 6%mechanical foam typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 25 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 141 capacity 6 ltrs. 142 supply & fixing of co2 type fire extinguisher conforming to is:15683:2018, charged with co2 gas ( purity 99.7% conforming to is 15222 ) , powder coated internal & external surface manganese steel isi marked as per is 7285 cylinder body , wheel type forged brass release valve isi marked as per is 3224 with inbuilt safety release device ( ( fusible plug and rupture disc type ) , 1.0 mtr. metal wire braided hose having minimum bursting pressure of 140 kgf / cm2, horn with metallic thread connection, qr code for product traceability, including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 143 capacity 4.5 kg. 144 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 4 kg 146 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 1.5 tr iseer not less then 4.6 148 2.0 tr iseer not less then 4.6 149 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 25 mm 151 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 4 kva 153 5 kva 154 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 155 50 mm dia per running inch length 156 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 157 sitc of interconnecting refrigerantcopper pipe forsplit / ductable / casseette ac of dhe grade c12200 astm b68, b75, chemical composition of copper % 99.0 min and phosphorus % 0.015 to 0.040 . for annealed copper tube : tensile strength = 210 mpa wih elongation % = 40 min . ink markbrand printing on hard tubes should be present. piping between each set of indoor & outdoor units of different sizesas per oem requirement & specifications including class o nitrile rubber sleeves, chase cutting, supports, making good the same with sand cement plaster etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 supplying and drawing flexible / stranded bare copper conductor, pvc / xlpe insulated, overall aluminium mylar tape shielded atc drain wire and outer pvc sheathed industrial instrumentation ( shielded ) cables voltage grade 300 / 500 v as per bs / en 50288 7 in existingsurface or recessed pvc / ms conduit / casing capping / cable tray / open duct making connections, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for cables. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 159 un armoured 160 4 core x 2.5 sq.mm 161 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 162 single pole mcb ( with b / c curve tripping characteristics ) 163 0.5 a to 5 a rating 164 6 a to 32 a rating 165 double pole mcb ( with b / c curve tripping characteristics ) 166 50 / 63 a rating 167 triple pole mcb ( with d curve tripping characteristics ) 168 6 a to 32 a rating 169 50 / 63 a rating 170 four pole mcb ( with b / c curve tripping characteristics ) 171 50 / 63 a rating 172 40 a rating 173 providing & fixing of 240 / 415 v residual current circuit breaker ( rccb ) conforming to ( is:12640 1 ) / iec 61008 1 , rated 4 kv impulse withstand voltage truly current operated and shall operate on cbct mechanisum, provision for pad lock, min. operation 10, 000 upto 63 a rating and5000 for 100 aratingand minimum phase termination capacity of 35 sq.mm. rigid wire, ip 20 contact protection with existing distribution board / sheetincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 174 two pole 100 / 300ma sensitivity 175 40 a rating 176 63 a rating 177 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 178 glazed door ( single phase ) ik 09 and ip 43 with metal end box 179 12 way ( 12+2 ) 180 metal door ( three phase ) per phase isolation, horizontal ik 09 and ip 43 with metal end box 181 4way ( incomer 8, sub incomer2+2+2 ) 182 6way ( incomer 8, sub incomer2+2+2 ) 183 8way ( incomer 8, sub incomer2+2+2 ) 184 12 way ( incomer 8, sub incomer2+2+2 ) 185 providing & fixing of recessed / surface mounting heavy duty vertical tpn distribution board with metal end box with provision of incomer suitable for 3 / 4 pole mccb and sp / tp mcb as outgoing , made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted with reversible door ( for double door db only ) complete with insulated 160 ( upto 160 a incomer ) / 250 amp. copper bus bar, neutral bars with shrouds, earth bar , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 186 double door ip 43 & ik 09 with provision of incomer mccb 100 / 125 a rating with metal end box 187 4 way 188 6 way 189 8 way 190 12 way 191 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 192 6.0 sq. mm 193 4 core 194 10.0 sq. mm 195 4 core 196 16.0 sq. mm 197 4 core 198 35.0 sq. mm 199 3.5 core 200 70.0 sq. mm 201 3.5 core 202 95.0 sq. mm 203 3.5 core 204 185.0 sq. mm 205 3.5 core 206 add extra for laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv gradedirect in ground including excavation of trench of size 75 cm ( depth ) x 35 cm ( width ) , with procedure as per followingpoints: ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay the cable in the middle of the trench, ( c ) provide river sand bed of height 125 mm on top of the cable, ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm widejust above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth 207 add extra for laying of one number additional pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv gradedirect in ground in the same trench in one tier horizontal formation including excavation of trench of size additional 20 cm in width, with procedure as per following points : ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay another cable in middle of trench in such manner that spacing between another cable is 20 cm., ( c ) provide river sand bed of height 125 mm on top of the cable. ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm widejust above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth. 208 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 209 3.5 x 185.0 sq.mm 210 3.5 x 95.0 sq.mm 211 3.5 x 70.0 sq.mm 212 3.5 x 35.0 sq.mm 213 4 x 16.0 sq.mm 214 4 x 10.0 sq.mm 215 4 x 6.0 sq.mm 216 supply, fabricating & installing following sizes of perforated hot dipped galvanized iron cable tray ( galvanized thickness not less then 50 microns ) with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers tees, cross members and other accessories as required and duly suspended from the ceiling with gi suspenders including gi bolts & nuts , fastners, supports etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 217 150mm x 50mm x 1.6mm 218 p / l of double wall corrugated hdpe pipe confirming to is : 16205 p 24, stiffness class750 n, externally corrugated and having smooth surface insidewith hdpe coupler, elbow, teeat required depth below the ground for laying cable of followingnominal outer dia.mfr test reportfrom nabl accrediated is to be submitted. ( excavation of earth& back filling with compaction is to be paid extra ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 219 50 mm 220 110 mm 221 plate earthing as per is:3043 withcopper earth plate of purity >95% of size 600mm x 600mm x 3.0mm by embodying3 mtr. below the ground level with 20mm dia. g.i. b class watering pipe , including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. and embodying the pipecomplete with alternate layers salt and coke / charcoal, testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 222 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 223 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 224 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 225 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 226 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 227 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 228 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 229 25 mm thick and 3 mtr. long 230 supply & laying following size earth stripin horizontal or vertical run in surface by means of earth strip dmc insulatorincluding riveting / soldering / welding, jointing shall be done by overlapping and with 2 set of brass ( for cu strip ) / gi ( for gi strip ) nut bolt & spring washer spaced at 50cm making connection etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 231 25mm x 3mm g.i. ( hot dipped ) strip 232 50mm x 6mm g.i. ( hot dipped ) strip 233 40mm x 6mm copper strip 234 supply & laying following size b class , g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with accessories like bend, socket etc.for laying earth conductor / strip / cable in ground / surface / recess as required.all as per pre approved by engineer in charge. ( earth excavation will be paid extra ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annex ure a attached with this bsr . 235 50 mm dia. 236 65 mm dia. 237 80 mm dia. 238 100 mm dia. 239 150 mm dia. 240 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 241 8 swg g.i. ( hot dipped ) wire 242 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 243 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 244 cat 6, un sheilded information outlet 245 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 246 single aperture 247 supply, installation, testing and comissioning of rack mounted 19 1u, cat6 24 port loaded, 1.5 1.6 mm crs chasis, powder coated, sheet steel, made of plastic ( abs ) , modular patch panelswith rear cable management system and mounting hardware to mount the patch panel. should have port identification numbers printed / engraved on front of the panel. etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 248 modular patch panel loaded with cat 6 i / o 249 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 250 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 251 1 mtr 252 2 mtr 253 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 254 15 u rack with width 600 mm & depth 400 mm + 100 mm 255 supply & installation of ip 20 & ik 08 , ul listed communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, vertical mounting rail 1.6 mm with umarking, front sturdy sheet steel frame folded from one piece and welded with 5mm toughened glass door, with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, set of 75 mm height 4 castors, 2 of which have brakes, accessories like: 5 nos of 19 1u horizontal cable manager, 2 nos of vertical cable managers, 1 no. keyboard tray, 4 nos of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 2 no of 19 1u, mountable socket strips with 6 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 256 27 u rack with width 600 mm &depth 800 mm 257 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 258 providing & laying xlpe insulated three core armouredaluminiumcable for working voltage 11 k.v. ( e ) confirming is :7098 p 2withh4 grade electrolyticaluminium conductor confirming to is: 8130 class 2 of purity >99.6 %, insulation screening: extruded semiconducting compound followed by helically wrapped copper tape, round / flat strip armouring of cables , inner / outer sheath pvc type st 2 confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810 all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 259 3 core 185.0 sq.mm 260 add extra for laying of one number xlpe power cable of 11 / 33 kv ( earthed ) voltage gradedirect in ground including excavation of trench of size 120 cm ( depth ) x 35 cm ( width ) , with procedure as per followingpoints: ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay the cable in the middle of the trench, ( c ) provide river sand bed of height 125 mm on top of the cable. ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm wide just above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth 261 providing & making heat shrinkable type indoor / outdoor / straight through terminations / joint kitsuitable for11 kv / 33 kv ( earthed ) cable with required components, prepration of cable ends. type test report should be as per is13573:2011 which covered all sequence for table 2 for termination kit and table 3 for streightthrough joint inclusive thermal & dynamic short circuit test, humidity test, soil fog test. crosslinking shall be done out side factory with e beam / peroxide technology. extrusion process shall be in house oem within same vicinity. includingtesting etc. as required of following sizes. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 262 11 kv end termination kit indoor type 263 3 core 120 / 150 / 185 sq.mm 264 11 kv end termination kit outdoor type 265 3 core 120 / 150 / 185 sq.mm 266 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 267 open execution type 268 200 a 269 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 270 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 271 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 272 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 273 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 274 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 275 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 276 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 277 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 278 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 279 electrolytic grade aluminium bus bar 6010 grade 280 providing & fixing of is: 13875 & iec :61326 confirming led digital type ( up to 500 ) v range volt meter / direct ammeter / ct oertated ammeter / frequency meter / kwh meter / multi function meter / power analyzer of class 1 accuracyas per is : 1248 of size 96mm x 96 mm including making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 281 threephase amp+hz+pf+kw+kva+kvar+t.energy+thd i, thd v & run hrs 282 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 283 ring type tape wound ct 284 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 285 c t class 1, ratio 400 / 5 to 1200 / 5, burden 15 va 286 providing & fixing ofcam operated rotary ( auto / manual ) switches on existing panel with 2 way and off position using high grade engineering materialto international standards with cam assemblyinsulation of glass filled polyamide with high tracking index. for reliable and stable electrical and mechanical endurance double butt contacts with silver bi metal on copper should provided . contact assembly is of operating temp range 25 degree c to 55 degree c, frequency upto 10 khz. switch life under std. op. conditions shall be mechanically minimum 50000 operations @300 cycles / hour and electrically 10, 000 operations at 100% rated duty for 100 cycles / hour including making connection etc.as required . all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 287 32 amp 288 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 289 red / yellow / green colour 290 blue / white colour 291 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 292 11 kv, class b 2.5 mm thick with proof voltage 22 kv ac ( rms ) and break down voltage45 kv ac ( rms ) 293 providing & fixing of self healing ip20 mpp type shunt capacitor ( banks ) conforming to is:13340 41 / iec :831 1&2 or iec : 60831 1& 2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( psd ) and shall have dissipation factor less than 0.0025 at 50 hz, operating loss less than 0.30 watt per kvar. min over current capacity 1.8 times rated current & peak inrush current min. 300 times of rated current, llife expectancy greater than 100000hrs ( temp class 25 d ) in 440 v / 480 v capacitor and for 525 v should life expectancy minimum 1, 65, 000 hrs ( temp class 25 d ) including making connections, testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 294 heavy dutythree phase 525v, 50 hzcylindrical typecapacitor ( bank ) 295 providing & fixing of ip54 microprocessor based 3 ct’s for all 3 phasesensing compensationpower factor correction relay size 139mm x 139 mm, operating voltage 415 / 440 v, iec / en 61000 6 ( 2&4 ) having 3 ct sensing, sensitivity up to 50 milli amp secondary current , self analysing auto c / k setting according to targeted power factor setting, the relay shall havedigit display unit for display of real power factor, targeted power factor, lag / lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with rs 485, indication of switching on units, auto / manual status, and shall have over load protection, no volt release , having multi parameter like kw, kva, kvar, rms value, step switching time 2 sec to 1800 sec. lead & lag parameters, metering facility and3 no. class 0.5 cast resinct ( refer ct specs in this chapter ) for sensing the relay including making coonection with 1.5 sq.mm copper wire etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 296 12 to 14 stage 297 providing & fixing ofac operated heavy duty 230 / 440 volt power contactor as per pwd specification for electrical works, isi marked is / iec 60947 4 1 : 2000 having provision of mechanical interlocking, auxilary contacts, din rail mounting type including making connections, testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 298 3 pole power contactorswith following ac 3 rating 299 40 amp 300 providing & fixing of440 volt 3 pole capacitor ( ac 6 b ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors / reactors to limit the inrush current as per pwd specification for electrical works, is / iec 60947 4 1 : 2000, insulation voltage 1000v, impulse withstand voltage 8 kv, din rail mounting type including making connections, testing etc. as required. suitable for following capacity capacitor bank.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 301 up to 6 kvar 302 10 kvar 303 20.0 kvar 304 providing & fixing of mechanical / digital time switch having following day / week programme and minimum 100 hours reserve and ac1 rating of 16 20 amperes including making connection, programming conforming to iec 60730 1 and 60730 2 7 etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 305 one day & week reserve ( digital type ) 306 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 307 3 pole mccb with thermal magnetic release 308 160 amp , 25 ka, adjustable o / l & adjustable s / c setting, 309 4 pole mccb with thermal magnetic release 310 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 311 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 312 160 amp , 25 ka, adjustable o / l & adjustable s / c setting, 313 200 amp , 25 ka, adjustable o / l & adjustable s / c setting, 314 250 amp , 35 ka, adjustable o / l & adjustable s / c setting, 315 400 amp , 35 ka, adjustable o / l & adjustable s / c setting, 316 s i t c of star ratedaluminium wound distribution transformerof following rating 11 / 0.433kv delta star connected, vector group dyn 11, onan cooled & as per bee star 1 & bis approved as per is 2026 1977 & lossesas defined as per 2014 ( fourth revision ) level 1 . including standardaccessories like conservator, silica gel breather, radiator, fins, ht cable box & lt cable boxes, temperature rise in winding / oil 35 40 degree c upto 200 kva & 40 45 degree c for above 200 kva, isi marked drain valve, dial type temperature gauge, first filling of transformer oil as per is :335 1953, epoxy based paint, including carrying of pre commission testing & charging of transformer complete in all respect . 317 the transformer shall be subjected to routine factory tests ( as per is:2026 and is:1180 ) including testing from ctlof discombefore charging of transformer & complete installaion must be certified from electrical inspectorate office as per indian electricity rule, ( ctl testing charges and electrical inspection charges shall be reimbursed by the department to the contractor ) . all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 318 250 kva with off ltc ( +5% to 10% @ 2.5% ) 319 sitc of 11kv 630 amps 21ka for 3 sec. sf6 insulated, outdoor duty ( ip54 ) , extensible / non extensible typering main unit ( rmu ) manually operated in combination ofvcb modules andload break switch consisting of copper busbar in sf6 insulated 304 ( non ferrite non magnetic grade ) stainless steel enclosure of thickness 2.5mm with manometer.the hv switchgear and control gear should be confirming to iec 62271 100, iec 62271 200 2003 & iec 60694 1996. the rmu should be internal arc tested for 21ka for 1second with iac afl classification for gas tank. vacum interrupter of vcb should be rmu manufacturer’s own make.each feeder of rmu should have voltage presence indicator. . and compring offollowings: 1 no. microprocessor based self powered numerical relay with over current / earth fault & short circuit protection with each vcb feeder. 3 nos. protection ct shall be of burden 2.5va, ratio 50 / 1a, class of accuracy class 5p10for o / c and e / f protection for each vcb. 1 no. manometer for each tank, 1 nos. fault passage indicator, right angle boots for all the feeder modulesall the type test certificates as per iec from third partynabl / cpri / erda accrediated lab to be submitted. ( cost of rcc foundation / steel structure to be paid extra ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr 320 non extensible 3 way rmu with 1 no. vcb & 2 no. load break switch 321 sitc of ht metering cubical panel as approved by discoms fabricated out of 18 swg crca sheet steel in two compartment & ms angle of size 60mmx 6mm having provision for following: ( i ) provision for fixing trivector / import export meter ( to be supplied by discoms ) ( ii ) provision for fixing of combined ct pt set with copper strip for connection ( to be supplied by discoms ) , ( iii ) test terminal block, ( iv ) 6mm thick bakelite sheet on all sides, ( v ) 3 / 6 corex 1.5 / 2.5 sq.mm copper cable for interconnections, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 322 sitc of radiator cooled and turbo charged silent dg set ( as per latest cpcb emissionnorms ) havingspecifications as per a, b, c, d, e, f, g, h & i 323 a ) 1500 rpm diesel engine conforming to bs:649 / 5514 of suitable bhp ( up to 82.5 kva 6 cylinder or below required, 125 kva & above ratings 6 cylinder or aboverequired ) capable of taking 10% over loading for one hour after 12 hours of continuous operation., dry exhaust mainfold with hospital grade silencer and catalytic convertor ( isolated from main dg chamber ) , up to 3 m exhaust piping ( with lrb insulation & alum. cladding ) as required . 324 b ) ac brush less spdp alternator conform to bs 5000 ( part 99 ) or is / iec 60034 1. . alternator shall be self regulated with standard alternator protection ( over voltage , over speed & under voltage, under speed warning & shutdown ) .engine & alternator mounted on a common base frame & coupled through a flexible coupling or close coupled 325 c ) cpcb / arai approved standard canopy with weatherproof, powdercoated accoustic enclosure for dg set for sound attenuation fabricated from 1.6 mm crca sheet steel ( structure ) with sidewall fabricated from 1.6 mm crca sheet & filled with glasswool ( 96kg / m3 ) / foam. as per is8183 the doors of 28 / 40 / 50 / 85mm thick as perrating and fabricated from 1.6mm crca sheet packed with accoustic material, all doors / opening are sealed with neoprene / epdngaskets. the dg set has inbuilt / external in fuel tank to run 6 to 8 hrs as per oem standard, with protection and tripping of dg set against temperature of more than 50 degree centigrade. 326 d ) electronic / mechanical governor, manual & electric start , batteries with battry charger, engine instruments panel, avm pads all controls for operation of dg set are from outside the enclosure with dg control panel having microprocessor based genset monitoring like running hour, rpm, low lube oil tripping & control system, panel mounted mccb / acb of suitable rating, ammeter, voltmeter, pf meter, frequency meter, kwh meter, digital fuel display meter, ind.lamps etc. mounted inside enclosure , visible and accessible from outside. the enclosure should be suitable for following capacity dg sets and alternator. noise level shall be less than 75 db at a distance of 1 mtrs. duly certified by authorised agency etc. complete in all respect of following capacity : 327 e ) ( i ) accoustic glass wool wall thickness should not be less then 40mm and not less then 20mm pu foam upto rating 100 kva. ( ii ) .accoustic glass wool wall thickness should not be less then 65mm and not less then 50mm pu foam upto rating 250 kva. ( iii ) accoustic glass wool wall thickness should not be less then 100mm forrating above 250 kva. 328 f ) first filling of the fuel tank shall be done by contractor and the prevailing fuel cost at that time shall be reimbursed to the contactor by department. 329 g ) servicing contract of dg set from oems authorised service dealer as per oem guidelines during the dlp period shall be done by contractor including all consumables, actual charges shall be reimbursed to the contractor by end user department. 330 h ) manufacturer / oem must have its authorized service dealer in rajasthan. which can provide service within 6 hours of compalint registration. 331 i ) dg set will be offered for inspection and testing at manufacturers works in presence of departmental engineers. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 332 40 kva at 0.8 pf 415v 50hz 3 ? 333 sitc of plc based auto main failure ( amf ) panel fabricated from crca sheet steel 2 mmthick , powder coated finish , engine start & stopcommands, control relays , ammeter & voltmeterwith selector switches, control & 2 nos 4 pole power contactors with 2 no. of required size 4 pole mccb, timers, electronic hooter , visual & alarm indication for faults, ups, operator interface panel complete in all respect suitable for following capacity dg sets: appropriate test certificate / report of product / accessories from oem / panel manufecturer shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 334 20 to 40 kva 335 supply & fabrication steel structure with ms channel / angle / joist / ismb / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as requiredcomplete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 336 providing and fixing welded mesh / expanded metal mesh 25 mmx 25 mm x 3mm in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. including two coat of red oxide and two coat of enamel paint or more requiredcomplete with frame work with 50 x 50 x 6mm angle iron post 30 cm in ground embeded in cement concrete 1:3:6 ( 30x30x45cm ) at corner and every three mtr including painting with one coat of primer and two coat of enamel paint work will be done as per direction of engineer incharge of sizecomplete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 337 earth work in excavation / by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5m in width as well as 10 sum on plan ) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed: 338 random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 ( 1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size ) upto plinth level with cement mortar 1:6 ( 1 cement : 6 sand ) . 339 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level 340 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) 341 plaster on new surface on wall in cement sand mortar 1:4 including racking of joints etc. complete fine finish : 342 20mm thick 343 finishing wall with water proofing cement paint of approved brand and manufacture and or required shadetogive an even shade including all scaffolding: 344 new work ( two or more coats applied @ 3.84 kg / 10 sqm ) . 345 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 346 5.0 hp, 3 ø, ( 14 28 ) mtr, ( 995 500 ) lpm 347 sitc of contactoroem fabricated dol / star delta starter panel with switchgear selection as per type 2 cordinatiom chart andmade out from 1.6 mm thick powder coated crca sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, illuminated on / offpush buttons, ammeter, voltmeter, indicating lamps etc.suitable for following rating motors complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 348 for three phase submersible / mono block pump 349 3.0 hp to 5.0 hp ( dol starter ) 350 part b non bsr items based on market rate 351 sitc ofro water system with filtration stage = particulate filter membrane life enhancer filter sediment filter pre carbon filter ro membrane filter post carbon filter, input power rating 230 v ac , 50 hz, percentage of rejection tds 90% or better having following features ( a ) double purification by ro with ess or latest technology with tds indicator ( b ) .spin welded ro membrane housing to prevent tempering ( c ) . push fit components for leak proof performance ( d ) . fully automatic operation with auto start and auto off ( e ) . ss construction for corrosion free lifespan ( f ) . equally suitable for water from all bore wells, , overhead storage tanks, water tankers and even municipal taps ( g ) ro membrane flushing auto flush @ every start , every stop and every one hourof working for one minute. complete in all respect with following capacity. approved make:eureka forbes, kent, au smith, ion exchange, pentair. 352 purification capacity 50 lph, duty cycle 270 500 liters / day, 353 sitc of dome ip ir cctv cameras: network h.265 2mp ( full hd ) megapixel high frame rate mini dome camera with built in microphone:2mp ir dome camera with metal body and built in mic: 1 / 2.8 progressive scan cmos; resolution: 1920 × 1080@30fps or better; colour: 0.01 lux @ ( f1.2, agc on ) or better, h.265+ compression or better; 120 db true wdr or better; fixed 2.8 / 4mm lens; built in mic; 3d dnr; 40m ir range or better, triple streams; blc, 3d dnr, hlc; line crossing detection, intrusion detection; scene change detection; face detection; anti flicker, heartbeat, mirror, password protection, privacy mask, watermark, ip address filter; onvif ( profile s, profile g ) , isapi; built in micro sd / sdhc / sdxc slot, up to 128 gb or better; operating condition: 30 °c to +60 °c; ip67; 12dc & poe; certificate of compliance: ul, ce / fcc, bis, rohsapproved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 354 sitc of ip ir cctv bullet outdoor camera: network h.265 2mp ( full hd ) megapixel high frame rate ir bullet camera ( outdoor ) with metal body, 2mp full frame low light ir bullet camera: 1 / 2.5 progressive scan cmos; resolution: 1920 × 1080 or better; color: 0.002 lux @ ( f1.2, agc on ) or better; slow shutter; fixed 3.6 mm lens; triple streams; 3d dnr; 120db wdr; 50m ir range or better; line crossing detection, intrusion detection, object removal detection, unattended baggage detection, scene change detection; face detection; anti flicker, heartbeat, mirror, password protection, privacy mask, watermark, ip address filter; onvif ( profile s, profile g ) , isapi; roi; support micro sd / sdhc / sdxc card ( 128g ) , local storage and nas ( nfs, smb / cifs ) , anr; operating condition: 30 °c to +60 °c; ip67; 12dc & poe; metal body; built in junction box for cable management; certificate of compliance: ul, ce / fcc, bis / rohs approved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 355 sitc of raid 5 supported 32ch nvr with upto 48 tb hdd support 32ch ip inputs; dual os for redundancy; support anr technology;320mbps incoming bandwidth, supports up to 12mp full channel recording; support h.265 compression; 16ch syncronised playback @1080p; support raid 5; n+1 hot spare system; support 3rd party cameras; 4k output; minimum 8 sata hdd slots; each slot should suppport upto 6tb hdd; e sata interface; dual gigabit self adaptive ethernet interface; serial interace; usb interface; alarm in / out;dual power supply ( all cameras and storage nvr should be of same make for the smooth functioning of the system ) . certificate of compliance: ul, ce / fcc, bisapproved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 356 sitc of 3.5 6tb surveillance hard disk ( makes: seagate / wd / toshiba ) 357 sitc of workstation latest intel® i5 processor, with 17 led monitor screen intel chipset motherboard, 08 gb ram, 1 tb sata hdd at 7200 rpm, with 4gb gpu type higher end graphic card for h.265 compression technique with dual display ports / dvi / hdmi port, giga lan card, wireless keyboard, wireless optical mouse with original license windows software of approved makes: lenovo, hp, dell. 358 sitc of 55 flat smart screen hd profesional led with remote control and wall mount unit / floor stand complete with making connections etc of approved makes: lg, samsung, panasonic. 359 sitc of 5 kva 1 phase input, 1 phase output advance dsp controlled ups with igbt based rectifier, lcd display, double conversion / digital signal processing ups, with isolationtransformer, with 26ahx x 16 nos smf batteries for min 30 min back up, with ms rack for barreries and required cabling for incoming & outgoing connection of approved makes: numeric, eaton, emerson, apc. 360 supply, installation, testing & commissioning of managed layer 2 intelligent ethernet poe switches providing 08 x 10 / 100 / 1000 fast ethernet poe ports 67w or better and 2 dual purpose uplink ports ( provision for copper / fiber giga connectivity ) all switches & related fiber modules should be of same make & category for seamless integration with each other of approved makes: cisco catalyst series or equivalent in avaya, juniper ) 361 p & f of early streamer emission type lightning arrester on gi mast with air terminal configured as spheroid which is comprised ofseparate electrically isolated 4 panels surrounding an earthed central finial, the terminal shall be tested by cpri for impulse current of 45 ka ( 8 / 20 sec ) with 5 positive & 5 negative impulse, the arrester having following protection radius at level 1 approved makes :lpi ( australia ) , lpsfr ( france ) , sudafix ( uk ) , ef ( switzerland ) , abb 362 30 48 mtr. 363 s & laying of p.v.c. / xlpe insulated & p.v.c. sheathed down conductor of 70 sq.mm single core insulated flexible copper cable confirming to is:1554 p i / is :7098 p i of 1.1 kv withelectrolytic gradecopper made of copper rodsconfirming to is 613 1964, of purity >99.7 %, inner / outer sheath confirming to is:5831 with accessories as required. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810approved makes: polycab, rr, finolex....

Rajasthan State Road Development And Construction Corporation Limited - Rajasthan

36348916 tender for electrification work of iti building at kareda district bhilwara wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) virgin material pvc conduit & itsisi marked ( is:3419 1988 ) accessories, round tiles, 1.2 mm thickhot dipped galvanized modular box with earth terminal, 10a modular switch, modular face plate with grid plate, 3 pin ceiling rose / holder / 3 way connector, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 3 short point ( up to 3 mtr. ) 4 medium point ( up to 6 mtr. ) 5 long point ( up to 10 mtr. ) 6 wiring of twin control light point with 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) in recessed isi markedmms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, round tiles, 2 nos hot dipped galvanized m.s modularbox of 1.2 mm thickwith earth terminal, 2 nos10 a two way modular switch, 3 pin ceiling rose / holder / 3 way connector , modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 7 long point ( up to 10 mtr. ) 8 wiring of 3 / 5 pin 6 amp. light plug point with 1.5 sq. mm nominal sizefr pvc insulated unsheathed flexible copper conductor 1.1 kv gradeand 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade ( is:694 ) inrecessed isi marked mms ( is:9537 p iii ) pvc conduit & its isi marked ( is:3419 1988 ) accessories, hot dipped galvanizedmodular box of 1.2 mm thick with earth terminal, 10 a modularswitch, 3 / 5 pin 6 a modular socket, modular face plate with grid plate, screws, making connections, testing etc. as required.for specification of copperconductor, phenolic laminated sheets & electrical / wiring accessories refer chapter e 04, e 05 & e 07 for additional technical parameters of product / work refer annexure a attached with this bsr 9 on board 10 short point ( up to 3 mtr. ) 11 medium point ( up to 6 mtr. ) 12 long point ( up to 10 mtr. ) 13 s&f following sizes ( dia. ) of isi marked virgin material mms ( is:9537 p iii ) pvc conduit along withisi marked ( is:3419 1988 ) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. for additional technical parameters of product / work refer annexure a attached with this bsr 14 20 mm 15 25 mm 16 32 mm 17 40 mm 18 50 mm 19 s&f following sizesof isi marked ( is:14927 p ii ) virgin materialupvc trunking along with accessorieslike coupler, inner, outer, elbow, square box, tee, end cap etc. on surfacewithscrews, expansionfastenersas required. for additional technical parameters of product / work refer annexure a attached with this bsr 20 100 mm x 50 mm 21 150 mm x 50 mm 22 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, class 5 stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, in existingsurface or recessed pvc / ms conduit / casing capping making connections with copper lugs of suitable size, ferrules, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of product / work refer annexure a attached with this bsr 23 1 x 1.5 sq.mm 24 2 x 1.5 sq.mm 25 3x 1.5 sq.mm 26 1x 2.5 sq.mm 27 2 x 2.5 sq. mm. + 1x1.5sqmm 28 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 29 2 x 6.0 sq. mm. + 1 x 4.0 sq. mm. 30 2 x 6.0 sq.mm 31 2 x 4.0 sq.mm 32 4 x 10.0 sq.mm 33 4 x 16.0 sq.mm 34 supplying and drawing pe insulated & pvc sheathed unarmoured telephone cable with 0.5 mm dia. solid annealed electrolytic grade bare copper conductor as per is: 8130 / 84 &confirming to tec specification gr / wir / 06 03 march 2002in existingsurface or recessed conduit / casing capping. including ferruling on each pair for identification etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 35 2 pair 36 supply and laying of pe insulated jelly filledarmouredtelephone cable. with 0.6 mm thick solid annealed bare copper conductor and confirming to tec specificationsconfirming. to dot gr / cug 01 / aug.2003 in existing pipe / open trench / cable tray / on surface including making necessary connection, testing etc. as required of size. for additional technical parameters of product / work refer annexure a attached with this bsr 37 10 pair 38 50 pair 39 supplying and drawing coaxial cable 75 ohm impedance with foam pe insulated solid bare copper inner conductor, and ist outer conductor of bonded alum. tape and second outer conductor ofalum. alloy braidin existingsurface or recessed conduit / casing capping including making connections as required. for additional technical parameters of product / work refer annexure a attached with this bsr 40 rg 6 41 p / laying isi marked p.v.c. insulated submersible cable confirming to ( is:694 ) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from99.90 % purity copper, stranding in acc. to is:8130 / iec 60228 forlower watt loss , oxygen freefor less chances of oxidization, insulation pvc type a / c / d , flame retardant as per is 10810 53, better amperage rating as per is:3961 part 5, existing pipe / open trench / cable tray / on surface including making connection etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 42 2.5 sq.mm 3 core flat / round 43 4.0 sq.mm 3 core flat / round 44 6.0 sq.mm 3 core flat / round 45 p & f paper phenolic resin bondedlaminates confirming to is : 2036 1995 for boxes / frames including making holes for switches etc, with brass screws, washers / zinc platednut and bolts as required. for additional technical parameters of product / work refer annexure a attached with this bsr 46 3.0 mm thick 47 4.8 mm thick 48 6.4 mm thick 49 p & f 1.2mm thickm.s. recessed fan box, hexagonal / round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mmlength extended on each side . all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 50 p & f krone module with base framein the recess / surface made out of 1.2 mm thicksheet steel box, front openable, having locking arrangements duly powder painted, including dressing, ferrulingandpunchingof telephone cable with krone tool etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 51 10 pairs 52 50 pairs 53 supplying and fixing of power plug point with modular accessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal / connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofisi marked modular 16 amp. switch ( is :3854 ) and 6 / 16 amp. socket outlet ( is:1293 ) making connection , testing , etc. as required. for specification ofwiring accessories refer chaptere 07related item & for additional technical parameters of product / work refer annexure a attached with this bsr 54 p&f metal clad / plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain / bakelite base in recessed / surface mounting heavy duty enclosure made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted ( without mcb ) including making connections, testing etc.as required.for additional technical parameters of product / work refer annexure a attached with this bsr 55 20 amp, 3 pin + scrapping earth, 4 module 56 32 amp, 5 pin + scrapping earth, 8 module 57 making of hole in wall ( brick / stone ) of required and placing np 2 rcc pipe ring of required size for housing exhaust fan and making good the same, with cement plaster required of following size. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 58 up to 457 mm size 59 providing & fixing ofextra down rod of 15 mm dia . erw ( electrical resistance welded ) of 1.6mm nominal thick medium duty steelpipe including cutting, threading, drilling, fixing quarter pin etc as reqd.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 60 providing & fixing of single / multi tone electronic call bell as per pwd specification for electrical works, including making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 61 providing & fixing of modular type switch / bell push duly isi marked ( is :3854 ) with cm / l no. printed and made out of unbreakable and fire retardant vergin uv stabilized polycarbonatewith brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , minimum width ofswitch toggle ( push part ) should not less then 20mm, includingall as per pre approved by engineer in charge, making connections, testing etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 62 10 a one way switch 63 32 amp. 2 moduleswitch with ledindicator 64 providing & fixing of modular type lockable feature socket dulymade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required. for additional technical parameters of product / work refer annexure a attached with this bsr 65 6 a3 / 5 pin shuttered socket 66 25 amp. 2 module socket 67 providing & fixing of modular type 120 w step fan regulator duly isi marked ( is 11037:1984 ) with cm / l no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 68 5 step fan regulator 2 module 360 dgree rotating 69 providing & fixing of following modular accessories as per pwd specification for electrical works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith ip 20 rating , includingall as per pre approved by engineer in charge, making connections, testing etc. as required.for additional technical parameters of product / work refer annexure a attached with this bsr 70 t.v. coaxial socket 71 rj 11 telephone jack double line 72 blanking plate 73 modular mcb 6 a to 32 adp 74 providing & fixing offollowing size mounting grid plates with cover plates made from fire retardent uv established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 75 1 / 2 module 76 8 module 77 providing & fixing ofwiring accessories oem fabricated following size gi box of 1.2 mm thick with earthing terminal and adjustable floating clamp in recess / surface suitable for modular accessories as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 78 1 2 module 79 6 / 8 module 80 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from powder coated extruded aluminiumhousing with in built driver, system lumen efficacy = 110 lm / watt output, internal surge protection of 2.5 kv with short & open circuit protection , thd < 10% , p. f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing on housing. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 81 1170mm ( + / 10% ) led batten with min. lumen output 2200 lm 82 570mm ( + / 10% ) batten with min. lumen output 1000 lm 83 providing & fixing of ip 20 led recessed / surface mounted, round / sqauresmd mid power led downlight with power coated die cast aluminum housingwith uv stabilized non yellowish diffuser withbis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% . system lumen efficacy of = 110 lm / watt, thd < 10 % , pf.=0.95, cri >80, life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 84 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 85 surface mounting ( with extruded alumn. housing ) 86 minimum lumen output 1300 lm 87 minimum lumen output 1950 lm 88 providing & fixing of ip20, 2x2 led surface / recessedmounting mid power smd type led light fixture not less than 50mm housing depth made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 4 kv internal / external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection ( integral with light fixture ) . system lumen efficacy of = 120 lm / watt , thd < 10 % , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. 89 oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 90 surface moutning 91 minimum lumen output 4200 lm 92 providing & fixing of ip65 ik08 rated integrated smd mid power led bulk head type light fixture made from pressure die cast al housing suitable with integral driver, system lumen efficacy =100 lm / watt output , thd < 10% , p.f.=0.95, cri >80 , life time of minimum50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k / 5700°k / 6000°k / 6500°k ( as per ansi bin ) , maximum power consumption should not more than the specified rating and fixture shall be ofbis standard andtrade mark certificate ( t.c. ) . manufactures word mark / name engraved / embossing / screen printing onhousing. surge protection 4 kv. oem must have its own in house nabl lab setup for all testing facilities for led fixtures. ( lm79 & lm80 ) certificate / report from oem shall be submitted.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 93 minimum lumen output 1000 lm 94 providing & fixing of 400 mm sweepbldc technology oscillating type wall mounting / pedestal typefans with three speed, on andoff position, double wall bearing withfront and back 120 or moreribs guard; three no.blades, noise level should be <= 75 db, including fixing with anchor bolts, making connection testing etc. as required. ( with remote ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 95 wall mounting type with service value 2.0 cmm / w, min. air delivery 71 cmm 96 providing & fixing ofbeestar rated copper wounded double ball bearing capacitor start, aluminium body & metallicblade ceilingfanconforming to all the performance requirements laid down in is 374:2019 including all amendments, as applicable ; & carry bis licensing ( i.e. isi marking ) with down rod up to 80 cm with secondary support safety cable ( steel rope ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 97 1200 mm sweep bee 1 star rated ( service value >=4.0 to < 4.5 ) 98 providing & fixing ofof double ball bearing, copper wounded capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor , making connections, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 99 300 mm sweep 100 providing & fixing of heavy duty capacitor start, copper wounddouble ball bearing900 / 1400 rpm single phaseexhaustfan conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 101 300 mm sweep ( 900 / 1400 rpm ) 102 380 mm sweep ( 900 / 1400 rpm ) 103 providing & fixing ofof ventilating fans capacitor start, copper wounded, single phase with pvc impeller, abs body, automatic openable louver shutter in existing opening including making connection, testing etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 104 150 mm sweep 105 250 mm sweep 106 p & f of wall cowl with bird screen suitable for outside wall of exhaust fan openingof following size and made out from 24 swg gi sheet as per instructions of engineer in chargeincluding fixing with suitable fasteners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 107 suitable for 300 mm sweep exhaust fan 108 suitable for 380 mm sweep exhaust fan 109 providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket / pole. fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with uv stabilized pc ( uv stablization report submitted for uv cover ) / toughened glass coverand secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm / wt and potted driver& has a unique bis r number withinput voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driverefficiency >85%, thd ( i ) <10%humidity 10% to 90% rh working temp 5c to 45c .driver current <750ma. the luminaireshall be bis certified and trade mark certified. life expectancyequal or more than 50000 burning hrs with minimum 70% lumen maintened , cri >70 and cct 5700k +355k. surge protection shall be min = 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs.manufactures word mark / name engraved / embossing on die cast housing to allow traceability / authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 110 led street light fixture with minimum lumen output 11225 lm 111 supply and erection ofgalvanized iron pole with galvanizing done in single dipping ( average coating thickness minimum 65 microns ) continuously tapered poles having octagonal / circular cross sections designed to withstand the maximum wind speed as per is 875, the pole shaft shall be made from sheet steel ( ht steel conforming to grade s355jo ) and confirming to bsen 10025 and shall be continuously tapered with single longitudinal welding. there shall not be any circumferential welding. the welding of pole shaft shall be done by submerged arc welding ( saw ) process. pole shafts shall be provided with the rigid flange plate of suitable thickness ( fe 410 conforming to is 226 / is 2062 ) with provision for fixing 4 no. foundation bolts, this base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside.the octagonal poles shall have lockable door of approximate 500 mm length at the elevation of 500 mm from the base plate with bakelite sheet having 6a sp mcb and 16 sqmm stud type connector ( 4 nos ) inside the pole at door opening for cable connection of following length and dimension as per table p 01 with base plate and foundation bolt on the existing cement concrete foundation.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 112 poles with octagonal cross section 113 7 mtr. 114 supply and fixing of pole oem fabricated hot dipped galvanised m.s. overhang ( 48.3 x 3.25 mm ) with cap ( 400 x 88.9 / 114.3 x 3.25 mm ) over the existing poles. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 115 single arm overhang 116 providing and laying rcc foundation for octagonal / conical street light poles, high mast poles as per drawing attach at tablep 4with following procedure& all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 117 a ) excavation of pit for foundation size upto required depth from ground level 118 b ) dressing of pit and dry stone pitching 200 mm thick including supply of stones and preparing surface complete. 119 c ) providing and laying in position cement concrete of m 10 grade of 75 mm thickness 120 d ) reinforcement for r.c.c. work with tmt bars including straightening, cutting, bending, placing in position and binding all complete. 121 e ) centring and shuttering including strutting , propping etc. and removal of form work for footing and pedestal 122 f ) providing & fixing of 2 no. required sizeplb hdpe pipe& foundation bolt with template as per oem recommendations. 123 g ) providing and layingreinforce cement concrete of m 25 grade in footing and pedestal including curing the foundation for 7 days. 124 h ) providing and fixing nosing angle 40 mm x 40 mm x 6mm with 2 no. 100 mm long, 10 mm dia. lugs on each face. 125 pole foundation for octagonal pole from 7 mtr. to 9 mtr. 126 providing & fixing of ik08ip65 protected top / bottom mounted led post top luminarie made of single piece constructionpowder coated die cast alluminium housing with uv stabalized clear / frosted polycarbonate diffuser andaluminium anodised with sand blast reflector. the system level luminous efficacy =100 lumen / w. smd leds is to be used, system cri>70, cct: 3000 / 4000 / 6500 k. the integral electronic driver must be potted & has a unique bis r number must be potted & has a unique bis r number constant current and internal / external surge protection device of min. 4kv ( l n ) and efficiency > 85%, pf>0.9, thd<10% and input voltage range of 140 270v ac at 50hz. system life of 50000 burning hours with 70% of initial lumens maintained . driver current <750ma.fixture must be in compliance with bis standards and trade mark certificate complete in all respect.oem must have its own in house nabl lab setup for all testing facilities forled fixtures. ( lm79 / lm80 ) certificate / report with liable warranty of product / accessories from oem shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 127 minimum lumen output 4500 lm post top luminarie 128 providing & fixing of street light bracket made out from following size of b class , medium class g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with heavy duty pole clamp, saddles suitable fastners etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 129 40 mm dia. 130 supply , installation, testing and comissioning of is:1475 marked self contained drinking water cooler withhermeticallysealed compressor, non cfc refrigerent suitable for operation on 230v / 1ph / 50hz ac supply, full stainless steel ( ss304 ) body ( 0.8 mm thick ) and tank ( 0.5 mm thick ) , stainless steel water tray, minimum two nosbrass chrome plated faucets and suitable drainage system complete in all respect with requiredheight ms fabricated and painted angle iron frame ( cost of frame to be paid extra ) complete in all respect of the following capacity.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 131 cooling capacity 150 ltr. / hr. and storage capacity 150 ltrs 132 providing and laying non pressure np 3 classr.c.c. pipes including collars / spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) etc. as required. ( excavation of earth& back filling with compaction is to be paid extra ) . all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 133 200 mm dia. 134 labour charges for excavating trenches of required width for pipes dressing of sides, ramming of bottoms, depth up to 1.5 mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 mtr.: 135 all kind of soils 136 sitc of wall type following zone ( each zoneaccessing minimum 20 units ( detectors / devices ) ) conventional type microprocessor based with lcd display en / lpcb / ul listed / approved main control panel fabricated from 16 swg crca sheet steel sealed maintenance free ( smf ) batteries of min2x7ah of 12 v or as required.including the cost of all accessories, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 137 4 zone 138 sitcof en / lpcb / ul listed / approved conventional type manual call point resettable complete with glass, hammer and chain etc.including the cost of all accessories etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 139 sitc of en / lpcb / ul listed / approved conventional type hooter cum strobe including the cost of all accessories, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 140 supply & fixing of water + afff 6%mechanical foam typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 25 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 141 capacity 6 ltrs. 142 supply & fixing of co2 type fire extinguisher conforming to is:15683:2018, charged with co2 gas ( purity 99.7% conforming to is 15222 ) , powder coated internal & external surface manganese steel isi marked as per is 7285 cylinder body , wheel type forged brass release valve isi marked as per is 3224 with inbuilt safety release device ( ( fusible plug and rupture disc type ) , 1.0 mtr. metal wire braided hose having minimum bursting pressure of 140 kgf / cm2, horn with metallic thread connection, qr code for product traceability, including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 143 capacity 4.5 kg. 144 supply & fixing of dry powder agent ( as per is 4308:2019 ) , abc typefire extinguisher ( stored pressure type ) conforming to is:15683:2018 , powder coated internal & external surface deep drawn cylinder body of mild steel cr2 grade conforming to is: 513, squeeze grip forged brass release valve with inbuilt safety release device, diaphragm type, 0 to 28 bar range pressure gauge, 450 mm long epdm discharge tube, qr code for product traceability including fixing on wall with suitable anchor fasteners as required of following capacity. test certificates of all the parameters along with hydro test & burst test ( for cylinder body ) certificatefrom oem / external nabl accrediated lab is to be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 145 4 kg 146 supply , installation, testing and comissioning ofinverter type air cooled hi wall split type air conditioners with latest star rating system as per bee amended upto date complete with indoor unit ( idu ) , out door unit ( odu ) , surface / concealed copper refrigerant piping with insulation ( closed cell elastomeric nitrile rubber tubular pipe section ) upto 3 mtr ( idu to odu ) , copper power cable upto 3.5 mtr ( idu to odu ) , r 32 / r 410 green refrigerant, wireless remote control, suitable for working between 230v + / 10% with low & high voltage cutoff and50 hz , single phaseacsupply capable of performing cooling, dehumidification, air circulation of following capacity with scroll / rotary compressor. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 147 1.5 tr iseer not less then 4.6 148 2.0 tr iseer not less then 4.6 149 providing & fixing of is : 4985 2000 class 4 ( 10 kgf / sqcm ) upvc drain water piping withfittings ( is:7834 & 10kgf / sqcm ) like elbow, socket, tee, solvent cement jointing, support with ms hanger on ceiling or recessed in wallwith chasing & plastering with 6 mmthickclosedcellelastomeric nitrile rubberinsulation including leakage testing etc. as required of following nominal sizes. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 150 25 mm 151 supply, fixing and testing of following capacity iso certified company made wall mounted stabilizer having output voltage variation from 200 v to 250 v ( + / 5% ) with input voltage variation from 170 v to 260 v, time delay facility from 2 to 4 minute and high cutoff at 270 v with providing of 16 amp / 20 amp industrialplug top making connection etc complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 152 4 kva 153 5 kva 154 making hole in stone masonary / rcc wall / rcc slab with core cutter for accomodating refrigerant pipe / drain pipe / ms pipe / cables etc of following dia 155 50 mm dia per running inch length 156 supply & fixing ms powder coated stand suitable for 1.0 / 1.5 / 2.0 tr outdoor type of split ac.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 157 sitc of interconnecting refrigerantcopper pipe forsplit / ductable / casseette ac of dhe grade c12200 astm b68, b75, chemical composition of copper % 99.0 min and phosphorus % 0.015 to 0.040 . for annealed copper tube : tensile strength = 210 mpa wih elongation % = 40 min . ink markbrand printing on hard tubes should be present. piping between each set of indoor & outdoor units of different sizesas per oem requirement & specifications including class o nitrile rubber sleeves, chase cutting, supports, making good the same with sand cement plaster etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 158 supplying and drawing flexible / stranded bare copper conductor, pvc / xlpe insulated, overall aluminium mylar tape shielded atc drain wire and outer pvc sheathed industrial instrumentation ( shielded ) cables voltage grade 300 / 500 v as per bs / en 50288 7 in existingsurface or recessed pvc / ms conduit / casing capping / cable tray / open duct making connections, testing etc. as required. oem must have its own in house nabl lab setup for all testing facilities for cables. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 159 un armoured 160 4 core x 2.5 sq.mm 161 providing & fixing of 240 / 415 v ac mcb with positive isolation of 10 ka breaking capacity ( b / c / d tripping characteristic as per type of load andsite requirement ) 4 kv impulse withstand voltage, isi marked is 8828 ( 1996 ) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , ip 20 contact protection and fitted inexisting distribution board / sheets, minimum electrical operation 20, 000 upto 20 a rating and 10, 000 upto 63 a, 5000 for 80 a & above ratingincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 162 single pole mcb ( with b / c curve tripping characteristics ) 163 0.5 a to 5 a rating 164 6 a to 32 a rating 165 double pole mcb ( with b / c curve tripping characteristics ) 166 50 / 63 a rating 167 triple pole mcb ( with d curve tripping characteristics ) 168 6 a to 32 a rating 169 50 / 63 a rating 170 four pole mcb ( with b / c curve tripping characteristics ) 171 50 / 63 a rating 172 40 a rating 173 providing & fixing of 240 / 415 v residual current circuit breaker ( rccb ) conforming to ( is:12640 1 ) / iec 61008 1 , rated 4 kv impulse withstand voltage truly current operated and shall operate on cbct mechanisum, provision for pad lock, min. operation 10, 000 upto 63 a rating and5000 for 100 aratingand minimum phase termination capacity of 35 sq.mm. rigid wire, ip 20 contact protection with existing distribution board / sheetincluding making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 174 two pole 100 / 300ma sensitivity 175 40 a rating 176 63 a rating 177 providing & fixing of recessed / surface mounting heavy duty horizontal type double door ( metal / glazed ) distribution board with metal end box made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3, powder painted complete with reversible door ( for double door db only ) 100 amp. insulated copper bus bar / shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 178 glazed door ( single phase ) ik 09 and ip 43 with metal end box 179 12 way ( 12+2 ) 180 metal door ( three phase ) per phase isolation, horizontal ik 09 and ip 43 with metal end box 181 4way ( incomer 8, sub incomer2+2+2 ) 182 6way ( incomer 8, sub incomer2+2+2 ) 183 8way ( incomer 8, sub incomer2+2+2 ) 184 12 way ( incomer 8, sub incomer2+2+2 ) 185 providing & fixing of recessed / surface mounting heavy duty vertical tpn distribution board with metal end box with provision of incomer suitable for 3 / 4 pole mccb and sp / tp mcb as outgoing , made out from galvanized steel / crca sheet not less then 1.2 mm thick conforming to is 8623 1 & 3 / iec 61439 1 & 3. powder painted with reversible door ( for double door db only ) complete with insulated 160 ( upto 160 a incomer ) / 250 amp. copper bus bar, neutral bars with shrouds, earth bar , color coded interconnecting wire set of suitable rating and din bar, masking sheet, making internal db terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. oem shall have submitnabl / cpri / erda accrediated lab type test reports& all as per pre approved by engineer in charge.for additional technical parameters of product / work refer annexure a attached with this bsr 186 double door ip 43 & ik 09 with provision of incomer mccb 100 / 125 a rating with metal end box 187 4 way 188 6 way 189 8 way 190 12 way 191 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed arrmouredaluminiumcable confirming to is:1554 p i / is :7098 p i of 1.1 kv withh4 grade electrolyticaluminium conductor confirming to is 8130 of purity >99.6 %, round / flat strip armouring of cables, inner / outer sheath confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray ( with cable tie ) includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810.for additional technical parameters of product / work refer annexure a attached with this bsr 192 6.0 sq. mm 193 4 core 194 10.0 sq. mm 195 4 core 196 16.0 sq. mm 197 4 core 198 35.0 sq. mm 199 3.5 core 200 70.0 sq. mm 201 3.5 core 202 95.0 sq. mm 203 3.5 core 204 185.0 sq. mm 205 3.5 core 206 add extra for laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv gradedirect in ground including excavation of trench of size 75 cm ( depth ) x 35 cm ( width ) , with procedure as per followingpoints: ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay the cable in the middle of the trench, ( c ) provide river sand bed of height 125 mm on top of the cable, ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm widejust above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth 207 add extra for laying of one number additional pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv gradedirect in ground in the same trench in one tier horizontal formation including excavation of trench of size additional 20 cm in width, with procedure as per following points : ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay another cable in middle of trench in such manner that spacing between another cable is 20 cm., ( c ) provide river sand bed of height 125 mm on top of the cable. ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm widejust above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth. 208 supplying and making one end termination with nickel plated heavy duty brass single compression gland ( as per is 12943 1990 ) ) sibg type consisting of check nut, gland body, metal washer ( 3 nos. ) , outer seal rubber ring, compression nut, heavy duty aluminium lugs ( as per is 8309 1993 ) duly crimped with crimping tool, pvc tape as peris 8337 1976offollowing size ofpvc insulated & pvc sheathed / xlpe aluminium conductor cable of 1100 volt grade as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 209 3.5 x 185.0 sq.mm 210 3.5 x 95.0 sq.mm 211 3.5 x 70.0 sq.mm 212 3.5 x 35.0 sq.mm 213 4 x 16.0 sq.mm 214 4 x 10.0 sq.mm 215 4 x 6.0 sq.mm 216 supply, fabricating & installing following sizes of perforated hot dipped galvanized iron cable tray ( galvanized thickness not less then 50 microns ) with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers tees, cross members and other accessories as required and duly suspended from the ceiling with gi suspenders including gi bolts & nuts , fastners, supports etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 217 150mm x 50mm x 1.6mm 218 p / l of double wall corrugated hdpe pipe confirming to is : 16205 p 24, stiffness class750 n, externally corrugated and having smooth surface insidewith hdpe coupler, elbow, teeat required depth below the ground for laying cable of followingnominal outer dia.mfr test reportfrom nabl accrediated is to be submitted. ( excavation of earth& back filling with compaction is to be paid extra ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 219 50 mm 220 110 mm 221 plate earthing as per is:3043 withcopper earth plate of purity >95% of size 600mm x 600mm x 3.0mm by embodying3 mtr. below the ground level with 20mm dia. g.i. b class watering pipe , including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. and embodying the pipecomplete with alternate layers salt and coke / charcoal, testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 222 supplyandinstallationofhigh tensile low carbon steel rod molecularly bonded with 99.9 % copperthickness ( 250 microns ) andconfirming toul 467, is / iec 62561 2of following size and length and as per point mentioned ( a ) , ( b ) , [ c ) , ( d ) , ( e ) below : 223 ( a ) bore a hole of dia. 100 mm of required length, place the rod in the centre of hole 224 ( b ) filled with anti corrosiveconductivecompounds with the permanent sealings at both the ends, cpri / erdatested with rms capacity of minimum 30 ka for withstanding 1 second .to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated labfor lowresistivity ( less than 0.12 ohm meter ) & high conductivity in nature with carbon as a major contentas per referance of is 3043 1987, ieee 80 2013 ( clause 14.5d ) , ieee 837 & ier 1956 with latest amendemnts 225 © connect the rod with copper strip / conductor / wire with suitable clamp made from tinned copper and ss 304 bolt 226 ( d ) place heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height250 to 300 mm. 227 ( d ) testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book. 228 ( e ) test certificatesfor confirming above standards from oem is mandatory. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 229 25 mm thick and 3 mtr. long 230 supply & laying following size earth stripin horizontal or vertical run in surface by means of earth strip dmc insulatorincluding riveting / soldering / welding, jointing shall be done by overlapping and with 2 set of brass ( for cu strip ) / gi ( for gi strip ) nut bolt & spring washer spaced at 50cm making connection etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 231 25mm x 3mm g.i. ( hot dipped ) strip 232 50mm x 6mm g.i. ( hot dipped ) strip 233 40mm x 6mm copper strip 234 supply & laying following size b class , g.i. pipe confirming to is : 1239 p 1 ( 2004 ) with accessories like bend, socket etc.for laying earth conductor / strip / cable in ground / surface / recess as required.all as per pre approved by engineer in charge. ( earth excavation will be paid extra ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annex ure a attached with this bsr . 235 50 mm dia. 236 65 mm dia. 237 80 mm dia. 238 100 mm dia. 239 150 mm dia. 240 supply & laying following size earth wire in horizontal or vertical run in ground / surface / recess including riveting, soldering, saddles, making connection with gi / cu purity purity >95%thimble etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 241 8 swg g.i. ( hot dipped ) wire 242 supply, drawing and testing of 4 pair, 23 awg solid bare copper wire insulated with pvc, utp ( unshielded twisted pair ) , category 6, class e, 100 ohm impedance, indoor cable as per latest ammendments of ansi / tia / eia 568 , the copper conductors should be balanced twisted in pairs, seperated by a cross member fluted pair divider & protected bypvc jacket. certified performance in a 4 connector configuration upto 100 mtrs channel requirements & transmission frequencies up to 250 mhz. in existing ms / pvc conduits / casing capping including making connections to information outlets and patch panels with jack &ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 243 supply and installation of unsheilded / 360 degree sheilded information outlets made of high impact plastic body with abs, fr grade halogen free material with provision for protection against dust in jack, suitable for cat 6 / 6a application complying to latest ammendments, according. to cat. 6 / 6a channel, it should support channel as well as components requirements of cat.6 / 6a standards at frequencies of up to 250 to 500 mhz. cat 6 / 6a unshielded / shielded jack should be suitable to terminate 4 pair, 23 / 24 awg solid / stranded wire diameters, using 100 ohm unshielded / shielded balance twisted pair cable, the jack should have tooless / impact termination on reliable copper tin plated insulation displacement contact, with easy lock mechanism, it supports iec 60603 7 4 and complied with ansi / tia / eia 568 c.2 standard. jack should be rj11, rj12 & rj45 compatible. should support ethernet 1.2 gb / s atm, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) specifications in existing modular / ms boxes along with necessory connections as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 244 cat 6, un sheilded information outlet 245 supply & fixing of square faceplate for flush / surface mount information outlets single / dual or quad aperture , material should bepc+abs body, suitable for rj45 unshielded / shielded connection modules. should match with i. o. oem. dimensions should be 86mm x 86mm as required complete in all respect.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 246 single aperture 247 supply, installation, testing and comissioning of rack mounted 19 1u, cat6 24 port loaded, 1.5 1.6 mm crs chasis, powder coated, sheet steel, made of plastic ( abs ) , modular patch panelswith rear cable management system and mounting hardware to mount the patch panel. should have port identification numbers printed / engraved on front of the panel. etc. as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 248 modular patch panel loaded with cat 6 i / o 249 supply , installation and testing of 4 pair, 100 ohm impedance, cat 6 / 6a / class e / ea patch cords should be constructed of minimum 23 / 24 awg, stranded bare copper cable with frpvc / lszh jacket, with an enhanced performance by factory moulded rj45 connectors with strain relief boots as per ansi / tia / eia 568 c.2 suitable for cat 6 / 6a application complying to latest ammendments category 6 / 6a standards, according. to tia568c.2, iso / iec 11801, en 50173, iec 60603 7 51, en 60603 7, ieee 802.3an minimum requirement for 1g base t to 10g base t performance. patch cords shall be straight thru cable compatible with both t568 a and t568 b wiring schemes, should support ieee 802.3af / ieee 802.3at for poe applications, minimum 750 to 1000 mating cycles in plug contacts for long durability, should support ethernet 10gbase t, 1.2 gb / s atm, token ring 4 / 16, digital video and broadband / baseband analog video, voice over internet protocal ( voip ) .all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 250 cat 6, u / utp ( unscreened / un sheilded twisted pair ) patch cord 251 1 mtr 252 2 mtr 253 supply & installation of ip 20 & ik 08 , ul listedwall mounted double section communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door, vertical mounting rail 1.6 mm with umarking , with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19 angles with wall mounting provision on wall. accessories like: 1 no of 19 1u horizontal cable manager, 1 no of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 1 no of 19 1u, mountable socket strips with 5 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with suitable anchor fastneretc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 254 15 u rack with width 600 mm & depth 400 mm + 100 mm 255 supply & installation of ip 20 & ik 08 , ul listed communication enclosure ( rack ) made from powder coated ( 60 to 80 micron ) crca sheet, vertical mounting rail 1.6 mm with umarking, front sturdy sheet steel frame folded from one piece and welded with 5mm toughened glass door, with all round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, set of 75 mm height 4 castors, 2 of which have brakes, accessories like: 5 nos of 19 1u horizontal cable manager, 2 nos of vertical cable managers, 1 no. keyboard tray, 4 nos of 90 cfm 230v ac fan with 1 mts long cable, mounting hardware , 2 no of 19 1u, mountable socket strips with 6 nos of 5a universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 256 27 u rack with width 600 mm &depth 800 mm 257 supply , installation, testing and comissioning ofmanaged layer 2 intelligent 10 / 100 ethernet switch providing 24 x 10 / 100 / 1000 mbps giga ethernet ports / with min 2 sfp giga ports ( provision for fiber giga connectivity ) with related lan base software including making connections etc as required.all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 258 providing & laying xlpe insulated three core armouredaluminiumcable for working voltage 11 k.v. ( e ) confirming is :7098 p 2withh4 grade electrolyticaluminium conductor confirming to is: 8130 class 2 of purity >99.6 %, insulation screening: extruded semiconducting compound followed by helically wrapped copper tape, round / flat strip armouring of cables , inner / outer sheath pvc type st 2 confirming to is:5831in existing rcc / hume / stoneware / pvc pipe / open duct / cable trench / cable tray includingtesting etc. as required of following size. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810 all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 259 3 core 185.0 sq.mm 260 add extra for laying of one number xlpe power cable of 11 / 33 kv ( earthed ) voltage gradedirect in ground including excavation of trench of size 120 cm ( depth ) x 35 cm ( width ) , with procedure as per followingpoints: ( a ) make a river sand bed of height 125 mm along the trench, ( b ) lay the cable in the middle of the trench, ( c ) provide river sand bed of height 125 mm on top of the cable. ( d ) lay the protective common burnt clay f.p.s. bricks of class designation 75 / sand stone slabs of 50 mm thicknessand 225 mm wide just above the sand bed vertically across the cable ( approx. 9 no. bricks per mtr. ) , ( e ) backfill the excavated soil leaving 300 mm from the ground level, ( f ) lay the cable warning tape and again back fill the remaining portion of the trench upto the ground level and compacting the earth 261 providing & making heat shrinkable type indoor / outdoor / straight through terminations / joint kitsuitable for11 kv / 33 kv ( earthed ) cable with required components, prepration of cable ends. type test report should be as per is13573:2011 which covered all sequence for table 2 for termination kit and table 3 for streightthrough joint inclusive thermal & dynamic short circuit test, humidity test, soil fog test. crosslinking shall be done out side factory with e beam / peroxide technology. extrusion process shall be in house oem within same vicinity. includingtesting etc. as required of following sizes. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 262 11 kv end termination kit indoor type 263 3 core 120 / 150 / 185 sq.mm 264 11 kv end termination kit outdoor type 265 3 core 120 / 150 / 185 sq.mm 266 providing & fixing of iso certified company made on load change over switch, front handle operated, four pole 415 v as per pwd specificationfor electrical works conforming to is / lec 60947 3 : 1999 including connections , testing etc. as required .in the following rating.appropriate type test certificate / oem test report shall be submitted .all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 267 open execution type 268 200 a 269 sitc of ip 42 and general construction confirming to is:8623 : 1993, wall / free standing floor mounted dust and vermin proof compartmentalisedcubical panel as specifications andother parameters requiredas per point ( a ) , ( b ) , ( c ) , ( d ) , ( e ) , ( f ) , ( g ) , ( h ) as below: 270 ( a ) thickness of crca sheet shallbe 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / withoutdetachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided 271 ( b ) complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel.the panel having pe foam / neoprene rubber gasket of not less than 3mm thickness , required hardware , concealed hinged door with key type locking arrangement for equipment / switchgear earthed with 2.5 sq.mm braided copper wire. 272 [ c ) interconnection between bus bar and switchgears / cable shall be rigidly supported and made out by flexible copper wires ( up to 63 amp ) and by solid bus bar ( >63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only.all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgearis to be paid extra ) 273 ( d ) wiring between components within switchgear and incoming / outgoing cableshall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram. 274 ( e ) all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be ‘point to point’ ( no wire splitting or tee connections ) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging. 275 ( f ) floor mounted panel shall be mounted on base frame of ismcchannel size 100 x 50 x 5 mm ( to be paid extra ) 276 ( g ) tests: the insulation resistance ( with 1000 v megger ) and high voltage power frequency test ( by applying a voltage of 2.5kv for one minute ) shall be measured between phases, between phase and neutral and between phase and earth. both before and after high voltage power frequency test. the insulation resistance shall not be less than three megaohm. ct secondary current injection test shall also be carried out. 277 ( h ) only outer surface area on all sides shall be measured & panel to be fabricated only from cpri approved fabricator only ( cpri test certificates to be submitted ) all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 278 supplying and fixing of aluminium ( iec 60105 iso 209 1, 2 ) / copper ( iec 60028 ) bus bar by means of smc / dmc type insulatorwith standard short circuit withstand capacity, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable pvc sleeves. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 279 electrolytic grade aluminium bus bar 6010 grade 280 providing & fixing of is: 13875 & iec :61326 confirming led digital type ( up to 500 ) v range volt meter / direct ammeter / ct oertated ammeter / frequency meter / kwh meter / multi function meter / power analyzer of class 1 accuracyas per is : 1248 of size 96mm x 96 mm including making connection by pvc insulated copper conductor with pvc sleeves / channel etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 281 threephase amp+hz+pf+kw+kva+kvar+t.energy+thd i, thd v & run hrs 282 providing & fixing of bis approvedcurrent transformeras per pwd specification for electrical works , isi marked as peris 2705 1992 / conforming to iec 60044 1, with secondary terminalof ct shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as requiredcurrent transformer ring type tape wound / resin cast wound as per is 16227 with, accuracy cl, ct ratio and burden as specified. isf<=5, cu cross section of secondary wire 1.5sqmm ( minimum ) , including all necessary support in existing panel including connection etc. as required . all as per pre approved by engineer in charge.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 283 ring type tape wound ct 284 c t class 1, ratio 200 / 5 to 300 / 5, burden 10 va 285 c t class 1, ratio 400 / 5 to 1200 / 5, burden 15 va 286 providing & fixing ofcam operated rotary ( auto / manual ) switches on existing panel with 2 way and off position using high grade engineering materialto international standards with cam assemblyinsulation of glass filled polyamide with high tracking index. for reliable and stable electrical and mechanical endurance double butt contacts with silver bi metal on copper should provided . contact assembly is of operating temp range 25 degree c to 55 degree c, frequency upto 10 khz. switch life under std. op. conditions shall be mechanically minimum 50000 operations @300 cycles / hour and electrically 10, 000 operations at 100% rated duty for 100 cycles / hour including making connection etc.as required . all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 287 32 amp 288 providing & fixing of110 / 220 v, unibody led indicatinglamp iec 60947with integral circuit, ip 65 above panel &ip 20 terminal block, approx. body dia for panel not less then 20 mm, length min. 50mm, front led cover dia min.29 mm, contact material phospher bronze for led, pcb contacts shall be ofbrass ( tin plated ) , impulsedielectric tested for 2.5 kv, rated insulation resistance shall be 100 m ohm at 500vdcincluding connection etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 289 red / yellow / green colour 290 blue / white colour 291 providing & fixing of electricalinsulating rubber matts as per pwd specification for electrical works, isi marked confirming to is: 15652 / 2006with one sideanti skid abberation marks and pasting the mat with synthetic rubber adhesive as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 292 11 kv, class b 2.5 mm thick with proof voltage 22 kv ac ( rms ) and break down voltage45 kv ac ( rms ) 293 providing & fixing of self healing ip20 mpp type shunt capacitor ( banks ) conforming to is:13340 41 / iec :831 1&2 or iec : 60831 1& 2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector ( psd ) and shall have dissipation factor less than 0.0025 at 50 hz, operating loss less than 0.30 watt per kvar. min over current capacity 1.8 times rated current & peak inrush current min. 300 times of rated current, llife expectancy greater than 100000hrs ( temp class 25 d ) in 440 v / 480 v capacitor and for 525 v should life expectancy minimum 1, 65, 000 hrs ( temp class 25 d ) including making connections, testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 294 heavy dutythree phase 525v, 50 hzcylindrical typecapacitor ( bank ) 295 providing & fixing of ip54 microprocessor based 3 ct’s for all 3 phasesensing compensationpower factor correction relay size 139mm x 139 mm, operating voltage 415 / 440 v, iec / en 61000 6 ( 2&4 ) having 3 ct sensing, sensitivity up to 50 milli amp secondary current , self analysing auto c / k setting according to targeted power factor setting, the relay shall havedigit display unit for display of real power factor, targeted power factor, lag / lead capacitor switching status, alarm output for under current, over current, insufficient compensation, communication interface with rs 485, indication of switching on units, auto / manual status, and shall have over load protection, no volt release , having multi parameter like kw, kva, kvar, rms value, step switching time 2 sec to 1800 sec. lead & lag parameters, metering facility and3 no. class 0.5 cast resinct ( refer ct specs in this chapter ) for sensing the relay including making coonection with 1.5 sq.mm copper wire etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 296 12 to 14 stage 297 providing & fixing ofac operated heavy duty 230 / 440 volt power contactor as per pwd specification for electrical works, isi marked is / iec 60947 4 1 : 2000 having provision of mechanical interlocking, auxilary contacts, din rail mounting type including making connections, testing etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 298 3 pole power contactorswith following ac 3 rating 299 40 amp 300 providing & fixing of440 volt 3 pole capacitor ( ac 6 b ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors / reactors to limit the inrush current as per pwd specification for electrical works, is / iec 60947 4 1 : 2000, insulation voltage 1000v, impulse withstand voltage 8 kv, din rail mounting type including making connections, testing etc. as required. suitable for following capacity capacitor bank.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 301 up to 6 kvar 302 10 kvar 303 20.0 kvar 304 providing & fixing of mechanical / digital time switch having following day / week programme and minimum 100 hours reserve and ac1 rating of 16 20 amperes including making connection, programming conforming to iec 60730 1 and 60730 2 7 etc. as required.all as per pre approved by engineer in charge. for additional technical parameters of products / work, refer annexure a attached with this bsr . 305 one day & week reserve ( digital type ) 306 sitc of3 / 4pole current limiting moulded case circuit breaker ( mccb ) made of flame retardent & heat resistant materialhaving following current rating, short circuitbreaking capacityat 440 / 415 v, 50 hz; o / l & s / c settings , conforming to is / iec 60947 p 2 :2003 with frontface and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push ( test ) to trip, trip time less then 10 ms under s / c condition, breaking capacity ics = 100% icu. u imp =8 kv, rated insulation voltage690 v.provision for uvr , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connectionsetc. as required.oem shall have submitnabl / cpri / erda accrediated lab type test certificate before execution all as per pre approved by engineer in charge. for additional technical parameters of product / work refer annexure a attached with this bsr 307 3 pole mccb with thermal magnetic release 308 160 amp , 25 ka, adjustable o / l & adjustable s / c setting, 309 4 pole mccb with thermal magnetic release 310 up to 100 amp , 25 ka, adjustable o / l & adjustable s / c setting, 311 125 amp , 25 ka, adjustable o / l & adjustable s / c setting, 312 160 amp , 25 ka, adjustable o / l & adjustable s / c setting, 313 200 amp , 25 ka, adjustable o / l & adjustable s / c setting, 314 250 amp , 35 ka, adjustable o / l & adjustable s / c setting, 315 400 amp , 35 ka, adjustable o / l & adjustable s / c setting, 316 s i t c of star ratedaluminium wound distribution transformerof following rating 11 / 0.433kv delta star connected, vector group dyn 11, onan cooled & as per bee star 1 & bis approved as per is 2026 1977 & lossesas defined as per 2014 ( fourth revision ) level 1 . including standardaccessories like conservator, silica gel breather, radiator, fins, ht cable box & lt cable boxes, temperature rise in winding / oil 35 40 degree c upto 200 kva & 40 45 degree c for above 200 kva, isi marked drain valve, dial type temperature gauge, first filling of transformer oil as per is :335 1953, epoxy based paint, including carrying of pre commission testing & charging of transformer complete in all respect . 317 the transformer shall be subjected to routine factory tests ( as per is:2026 and is:1180 ) including testing from ctlof discombefore charging of transformer & complete installaion must be certified from electrical inspectorate office as per indian electricity rule, ( ctl testing charges and electrical inspection charges shall be reimbursed by the department to the contractor ) . all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 318 250 kva with off ltc ( +5% to 10% @ 2.5% ) 319 sitc of 11kv 630 amps 21ka for 3 sec. sf6 insulated, outdoor duty ( ip54 ) , extensible / non extensible typering main unit ( rmu ) manually operated in combination ofvcb modules andload break switch consisting of copper busbar in sf6 insulated 304 ( non ferrite non magnetic grade ) stainless steel enclosure of thickness 2.5mm with manometer.the hv switchgear and control gear should be confirming to iec 62271 100, iec 62271 200 2003 & iec 60694 1996. the rmu should be internal arc tested for 21ka for 1second with iac afl classification for gas tank. vacum interrupter of vcb should be rmu manufacturer’s own make.each feeder of rmu should have voltage presence indicator. . and compring offollowings: 1 no. microprocessor based self powered numerical relay with over current / earth fault & short circuit protection with each vcb feeder. 3 nos. protection ct shall be of burden 2.5va, ratio 50 / 1a, class of accuracy class 5p10for o / c and e / f protection for each vcb. 1 no. manometer for each tank, 1 nos. fault passage indicator, right angle boots for all the feeder modulesall the type test certificates as per iec from third partynabl / cpri / erda accrediated lab to be submitted. ( cost of rcc foundation / steel structure to be paid extra ) all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr 320 non extensible 3 way rmu with 1 no. vcb & 2 no. load break switch 321 sitc of ht metering cubical panel as approved by discoms fabricated out of 18 swg crca sheet steel in two compartment & ms angle of size 60mmx 6mm having provision for following: ( i ) provision for fixing trivector / import export meter ( to be supplied by discoms ) ( ii ) provision for fixing of combined ct pt set with copper strip for connection ( to be supplied by discoms ) , ( iii ) test terminal block, ( iv ) 6mm thick bakelite sheet on all sides, ( v ) 3 / 6 corex 1.5 / 2.5 sq.mm copper cable for interconnections, etc. as required. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 322 sitc of radiator cooled and turbo charged silent dg set ( as per latest cpcb emissionnorms ) havingspecifications as per a, b, c, d, e, f, g, h & i 323 a ) 1500 rpm diesel engine conforming to bs:649 / 5514 of suitable bhp ( up to 82.5 kva 6 cylinder or below required, 125 kva & above ratings 6 cylinder or aboverequired ) capable of taking 10% over loading for one hour after 12 hours of continuous operation., dry exhaust mainfold with hospital grade silencer and catalytic convertor ( isolated from main dg chamber ) , up to 3 m exhaust piping ( with lrb insulation & alum. cladding ) as required . 324 b ) ac brush less spdp alternator conform to bs 5000 ( part 99 ) or is / iec 60034 1. . alternator shall be self regulated with standard alternator protection ( over voltage , over speed & under voltage, under speed warning & shutdown ) .engine & alternator mounted on a common base frame & coupled through a flexible coupling or close coupled 325 c ) cpcb / arai approved standard canopy with weatherproof, powdercoated accoustic enclosure for dg set for sound attenuation fabricated from 1.6 mm crca sheet steel ( structure ) with sidewall fabricated from 1.6 mm crca sheet & filled with glasswool ( 96kg / m3 ) / foam. as per is8183 the doors of 28 / 40 / 50 / 85mm thick as perrating and fabricated from 1.6mm crca sheet packed with accoustic material, all doors / opening are sealed with neoprene / epdngaskets. the dg set has inbuilt / external in fuel tank to run 6 to 8 hrs as per oem standard, with protection and tripping of dg set against temperature of more than 50 degree centigrade. 326 d ) electronic / mechanical governor, manual & electric start , batteries with battry charger, engine instruments panel, avm pads all controls for operation of dg set are from outside the enclosure with dg control panel having microprocessor based genset monitoring like running hour, rpm, low lube oil tripping & control system, panel mounted mccb / acb of suitable rating, ammeter, voltmeter, pf meter, frequency meter, kwh meter, digital fuel display meter, ind.lamps etc. mounted inside enclosure , visible and accessible from outside. the enclosure should be suitable for following capacity dg sets and alternator. noise level shall be less than 75 db at a distance of 1 mtrs. duly certified by authorised agency etc. complete in all respect of following capacity : 327 e ) ( i ) accoustic glass wool wall thickness should not be less then 40mm and not less then 20mm pu foam upto rating 100 kva. ( ii ) .accoustic glass wool wall thickness should not be less then 65mm and not less then 50mm pu foam upto rating 250 kva. ( iii ) accoustic glass wool wall thickness should not be less then 100mm forrating above 250 kva. 328 f ) first filling of the fuel tank shall be done by contractor and the prevailing fuel cost at that time shall be reimbursed to the contactor by department. 329 g ) servicing contract of dg set from oems authorised service dealer as per oem guidelines during the dlp period shall be done by contractor including all consumables, actual charges shall be reimbursed to the contractor by end user department. 330 h ) manufacturer / oem must have its authorized service dealer in rajasthan. which can provide service within 6 hours of compalint registration. 331 i ) dg set will be offered for inspection and testing at manufacturers works in presence of departmental engineers. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 332 40 kva at 0.8 pf 415v 50hz 3 ? 333 sitc of plc based auto main failure ( amf ) panel fabricated from crca sheet steel 2 mmthick , powder coated finish , engine start & stopcommands, control relays , ammeter & voltmeterwith selector switches, control & 2 nos 4 pole power contactors with 2 no. of required size 4 pole mccb, timers, electronic hooter , visual & alarm indication for faults, ups, operator interface panel complete in all respect suitable for following capacity dg sets: appropriate test certificate / report of product / accessories from oem / panel manufecturer shall be submitted. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 334 20 to 40 kva 335 supply & fabrication steel structure with ms channel / angle / joist / ismb / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as requiredcomplete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 336 providing and fixing welded mesh / expanded metal mesh 25 mmx 25 mm x 3mm in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. including two coat of red oxide and two coat of enamel paint or more requiredcomplete with frame work with 50 x 50 x 6mm angle iron post 30 cm in ground embeded in cement concrete 1:3:6 ( 30x30x45cm ) at corner and every three mtr including painting with one coat of primer and two coat of enamel paint work will be done as per direction of engineer incharge of sizecomplete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 337 earth work in excavation / by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5m in width as well as 10 sum on plan ) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed: 338 random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 ( 1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size ) upto plinth level with cement mortar 1:6 ( 1 cement : 6 sand ) . 339 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level 340 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) 341 plaster on new surface on wall in cement sand mortar 1:4 including racking of joints etc. complete fine finish : 342 20mm thick 343 finishing wall with water proofing cement paint of approved brand and manufacture and or required shadetogive an even shade including all scaffolding: 344 new work ( two or more coats applied @ 3.84 kg / 10 sqm ) . 345 sitc of single stage, water cooled, high speed ( 2880 rpm ) , horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t / c vs t / c, thrust bearing shall be ofcarbon + s.s.the stator body of single phase pumpshall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition ( ced ) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. oem shall have submitnabl / cpri / erda accrediatedlab type test certificate before execution. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 346 5.0 hp, 3 ø, ( 14 28 ) mtr, ( 995 500 ) lpm 347 sitc of contactoroem fabricated dol / star delta starter panel with switchgear selection as per type 2 cordinatiom chart andmade out from 1.6 mm thick powder coated crca sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, illuminated on / offpush buttons, ammeter, voltmeter, indicating lamps etc.suitable for following rating motors complete in all respect. all as per pre approved by engineer in charge.for additional technical parameters of products / work, refer annexure a attached with this bsr . 348 for three phase submersible / mono block pump 349 3.0 hp to 5.0 hp ( dol starter ) 350 part b non bsr items based on market rate 351 sitc ofro water system with filtration stage = particulate filter membrane life enhancer filter sediment filter pre carbon filter ro membrane filter post carbon filter, input power rating 230 v ac , 50 hz, percentage of rejection tds 90% or better having following features ( a ) double purification by ro with ess or latest technology with tds indicator ( b ) .spin welded ro membrane housing to prevent tempering ( c ) . push fit components for leak proof performance ( d ) . fully automatic operation with auto start and auto off ( e ) . ss construction for corrosion free lifespan ( f ) . equally suitable for water from all bore wells, , overhead storage tanks, water tankers and even municipal taps ( g ) ro membrane flushing auto flush @ every start , every stop and every one hourof working for one minute. complete in all respect with following capacity. approved make:eureka forbes, kent, au smith, ion exchange, pentair. 352 purification capacity 50 lph, duty cycle 270 500 liters / day, 353 sitc of dome ip ir cctv cameras: network h.265 2mp ( full hd ) megapixel high frame rate mini dome camera with built in microphone:2mp ir dome camera with metal body and built in mic: 1 / 2.8 progressive scan cmos; resolution: 1920 × 1080@30fps or better; colour: 0.01 lux @ ( f1.2, agc on ) or better, h.265+ compression or better; 120 db true wdr or better; fixed 2.8 / 4mm lens; built in mic; 3d dnr; 40m ir range or better, triple streams; blc, 3d dnr, hlc; line crossing detection, intrusion detection; scene change detection; face detection; anti flicker, heartbeat, mirror, password protection, privacy mask, watermark, ip address filter; onvif ( profile s, profile g ) , isapi; built in micro sd / sdhc / sdxc slot, up to 128 gb or better; operating condition: 30 °c to +60 °c; ip67; 12dc & poe; certificate of compliance: ul, ce / fcc, bis, rohsapproved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 354 sitc of ip ir cctv bullet outdoor camera: network h.265 2mp ( full hd ) megapixel high frame rate ir bullet camera ( outdoor ) with metal body, 2mp full frame low light ir bullet camera: 1 / 2.5 progressive scan cmos; resolution: 1920 × 1080 or better; color: 0.002 lux @ ( f1.2, agc on ) or better; slow shutter; fixed 3.6 mm lens; triple streams; 3d dnr; 120db wdr; 50m ir range or better; line crossing detection, intrusion detection, object removal detection, unattended baggage detection, scene change detection; face detection; anti flicker, heartbeat, mirror, password protection, privacy mask, watermark, ip address filter; onvif ( profile s, profile g ) , isapi; roi; support micro sd / sdhc / sdxc card ( 128g ) , local storage and nas ( nfs, smb / cifs ) , anr; operating condition: 30 °c to +60 °c; ip67; 12dc & poe; metal body; built in junction box for cable management; certificate of compliance: ul, ce / fcc, bis / rohs approved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 355 sitc of raid 5 supported 32ch nvr with upto 48 tb hdd support 32ch ip inputs; dual os for redundancy; support anr technology;320mbps incoming bandwidth, supports up to 12mp full channel recording; support h.265 compression; 16ch syncronised playback @1080p; support raid 5; n+1 hot spare system; support 3rd party cameras; 4k output; minimum 8 sata hdd slots; each slot should suppport upto 6tb hdd; e sata interface; dual gigabit self adaptive ethernet interface; serial interace; usb interface; alarm in / out;dual power supply ( all cameras and storage nvr should be of same make for the smooth functioning of the system ) . certificate of compliance: ul, ce / fcc, bisapproved make: samsung / hikvision / panasonic / infinova / cp plus / dahua / honeywell 356 sitc of 3.5 6tb surveillance hard disk ( makes: seagate / wd / toshiba ) 357 sitc of workstation latest intel® i5 processor, with 17 led monitor screen intel chipset motherboard, 08 gb ram, 1 tb sata hdd at 7200 rpm, with 4gb gpu type higher end graphic card for h.265 compression technique with dual display ports / dvi / hdmi port, giga lan card, wireless keyboard, wireless optical mouse with original license windows software of approved makes: lenovo, hp, dell. 358 sitc of 55 flat smart screen hd profesional led with remote control and wall mount unit / floor stand complete with making connections etc of approved makes: lg, samsung, panasonic. 359 sitc of 5 kva 1 phase input, 1 phase output advance dsp controlled ups with igbt based rectifier, lcd display, double conversion / digital signal processing ups, with isolationtransformer, with 26ahx x 16 nos smf batteries for min 30 min back up, with ms rack for barreries and required cabling for incoming & outgoing connection of approved makes: numeric, eaton, emerson, apc. 360 supply, installation, testing & commissioning of managed layer 2 intelligent ethernet poe switches providing 08 x 10 / 100 / 1000 fast ethernet poe ports 67w or better and 2 dual purpose uplink ports ( provision for copper / fiber giga connectivity ) all switches & related fiber modules should be of same make & category for seamless integration with each other of approved makes: cisco catalyst series or equivalent in avaya, juniper ) 361 p & f of early streamer emission type lightning arrester on gi mast with air terminal configured as spheroid which is comprised ofseparate electrically isolated 4 panels surrounding an earthed central finial, the terminal shall be tested by cpri for impulse current of 45 ka ( 8 / 20 sec ) with 5 positive & 5 negative impulse, the arrester having following protection radius at level 1 approved makes :lpi ( australia ) , lpsfr ( france ) , sudafix ( uk ) , ef ( switzerland ) , abb 362 30 48 mtr. 363 s & laying of p.v.c. / xlpe insulated & p.v.c. sheathed down conductor of 70 sq.mm single core insulated flexible copper cable confirming to is:1554 p i / is :7098 p i of 1.1 kv withelectrolytic gradecopper made of copper rodsconfirming to is 613 1964, of purity >99.7 %, inner / outer sheath confirming to is:5831 with accessories as required. oem must have its own in house nabl accrediated laboratory for testing procedure as per is:10810approved makes: polycab, rr, finolex....

North Western Railway - Rajasthan

36238787 supply of over hauling kit for brake cylinderover hauling kit for brake cylinder, over hauling kit for brake cylinder kbi make [ 1117429 / 1204 v or 1182516 / 1204 lp ] consisting of 27 item as per annexure a [ knorr bremse india pvt ltd ] kbi part no 1 ] b 24037 o ring =1 , 2 ] b 25145 / 21 shaft sealing ring =1 , 3 ] b 25145 / 25 shaft sealing ring =1, 4 ] b 25145 / 26 shaft sealing ring =1, 5 ] b 26669 spring washer p =7, 6 ] b 30779 o ring =1, 7 ] b 33687 / 14 o ring =1, 8 ] b 33793 / 2 hose clamp =1, 9 ] b 33793 / 6 hose clamp =1 , 10 ] b33793 / 8 hose clamp =1, 11 ] b 53267 / a washer =1, 12 ] b 65557 / 4 machine screw =1, 13 ] b75404 protective cap=1, 14 ] b 85886 / 5 hex head bolt =1, 15 ] c 57231 / 1 supporting roller =2, 16 ] 464360 retaining ring =2, 17 ] 462767 snap ring ==2, 18 ] 463250 clamping pin =1, 19 ] 465121 lock washer =1, 20 ] b 38079 collar =1, 21 ] 466250 clamping pin =1, 22 ] b 23166 thrust bearing needle=1, 23 ] b 66529 / 5 breather plug =1, 24 ] b 43640 washer=1, 25 ] b 65580 / 12 bellow =1, 26 ] 466885 locking ring =13, 27 466887 locking ring =3 specn: rdso spec. no. rdso / cg04 rev.01. [ warranty period: 36 months after the date of delivery ] carriage stores depot rajasthan 32.00 set ajmer , nwr...

North Western Railway - Rajasthan

36151981 supply of rc for kbi make spares for coaches, overhauling kit for dump valve to kbi part no 34652 / 15024 for lhb coaches of 07 items. s. no. 1. o ring a40125 / 6 02 nos. 2. o ring b31807 02 nos. 3 o ring a40125 / 2 02 nos. 4 o ring a91150 02 nos. 5. o ring b57679 02 nos. 6 strainer c62814 02 nos. 7 sealing ring 465372 01 nos. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 960.00 set ajmer , nwr , overhawling kit for check valve to kbi part no. 190476 for lhb coaches consisting of 03 items sn. 1 o ring k3581 1 nos. 2. o ring k4140 3 nos. 3. valve sealing disc 468676 1 nos. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 480.00 set ajmer , nwr , circut board eb01 for wsp system of lhb coaches kbi part no. stn 25799 / 01 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 16.00 numbers , circuit board pb03 a for wsp system of lhb coaches kbi part no. stn 25089 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 16.00 numbers , circut board mb 04b for wsp systemof lhb coaches. kbi part no.stn 28339 / 00000 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 11.00 numbers , distributor valve ke11pksl with suitable relay valve & mounting bkt ( lhb ) kbi part no i.2.765 & i.2.724. distributor valv offer accepted as e kedipksl with pressure convertor for lhb to kbi part no. i.2.765 and mounting bracket to kbi part no. i.2.724. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 15.00 numbers , speed sensor g16 to kbi part no. stn31450 / 205a 18u with 2 meters long cable only integral with speed sensor as per rdso spec no rdso / 2011 / cg 04 ( rev 1 ) with amendment no 1 appendix f. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 88.00 numbers ajmer , nwr , check valve rv7 t kbi part no 190476 for lhb coaches. [ warranty period: 30 months after the date of delivery ] page 2 of 11 run date / time: 08 / 02 / 2023 16:15:58stores / north western rly tender document , filter nw 19 with code pin for lhb coaches. part no. m / s knorr bremse wbfil 100aa002 special terms and conditions. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 15.00 numbers , brake caliper unit leverage ratio 2.17 without brake cylinder for lhb fiat bogie eog coaches to kbi part no. ii39700 / zb .confirm to rdso spec. no. rdso / 2011 / cg 04, rev 1 & amndt. 1. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 25.00 numbers , brake caliper unit leverage ratio 2.48 without brake cylinder for lhb fiat bogie power cars to kbi part no. ii39601 / za .confirming to rdso spec. no. rdso / 2011 / cg 04, rev 1 & amndt. 1. [ warranty period: 30 months after the date of delivery ] , led plate kbi part no.c133700 as per rdso spec. no. rdso / 2011 / cg 04 rev.01. [ warranty period: 30 months after the date of delivery ] , over hauling kit for brake cylinder kbi make [ 1117429 / 1204 v or 1182516 / 1204 lp ] consisting of 27 item as per annexure a [ knorr bremse india pvt ltd ] kbi part no 1 ] b 24037 o ring =1 , 2 ] b 25145 / 21 shaft sealing ring =1 , 3 ] b 25145 / 25 shaft sealing ring =1, 4 ] b 25145 / 26 shaft sealing ring =1, 5 ] b 26669 spring washer p =7, 6 ] b 30779 o ring =1, 7 ] b 33687 / 14 o ring =1, 8 ] b 33793 / 2 hose clamp =1, 9 ] b 33793 / 6 hose clamp =1 , 10 ] b33793 / 8 hose clamp =1, 11 ] b 53267 / a washer =1, 12 ] b 65557 / 4 machine screw =1, 13 ] b75404 protective cap=1, 14 ] b 85886 / 5 hex head bolt =1, 15 ] c 57231 / 1 supporting roller =2, 16 ] 464360 retaining ring =2, 17 ] 462767 snap ring ==2, 18 ] 463250 clamping pin =1, 19 ] 465121 lock washer =1, 20 ] b 38079 collar =1, 21 ] 466250 clamping pin =1, 22 ] b 23166 thrust bearing needle=1, 23 ] b 66529 / 5 breather plug =1, 24 ] b 43640 washer=1, 25 ] b 65580 / 12 bellow =1, 26 ] 466885 locking ring =13, 27 466887 locking ring =3 specn: rdso spec. no. rdso / cg04 rev.01. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 20.00 set ajmer , nwr , overhauling kit for distributor valve with rlv lhb coaches consisting 31 items make knorr bremse as per annuxure a atteched. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 180.00 set , pair of brake pad holder ( lh ) for brake caliper for lhb coaches as per m / s knorr bremse part no 176904 / a and brake pad holder ( rh ) for brake caliper for lhb coaches as per m / s knorr bremse part no. 176903 / a [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 22.00 numbers , brake cylinder with hand brake arrangement ( pbacm 254 130 ) for lhb coaches m / s. knorr bremse part no. ii 82516 / 1204 lp. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 6.00 numbers ajmer , nwr , rlv kit items for lhb dv consisting of 03 items of m / s knorr bremse 01. diaphragm a 49886 02 nos. 02. control sleeve b 25804 01 no 03. o ring 463074 01 no. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 240.00 set ajmer , nwr , brake cylinder left verson for lhb coaches to kbi part no. i70297 / 704ur and drg. no. c160859 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 13.00 numbers ajmer , nwr , emergency brake accelerator eb3 s / l without bracket kbi part no 189179. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 14.00 numbers , brake cylinder right version for lhbcoach to kbi part no. ii82515 / 304lp and drg. no. c177349 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 11.00 numbers ajmer , nwr , overhaul kit for emergency brake accelerator for lhb coaches to kbi part no.189179 consisting of 21 items list as per given below: s.no. description part no. qty / kit 1. retaining ring 464845 01 no. 2. grooved ring a18294 / 5 02 no. 3. valve tappet a 30530 01 no. 4. cup diaphragm a30711 01 no. 5. cup diaphragm a38362 01 no. 6. gasket a38363 01 no. 7. strainer a38433 / 1 01 no. 8. o ring a40125 / 14 02 no. 9. o ring a54062 04 no. 10. toothed ring a86235 / 1 01 no. 11. retaining ring a86239 01 no. 12. o ring a91453 01 no. 13 o ring b21836 01 no. 14. o ring b35265 01 no. 15. valve sealing ring b58852 / 6 01 no. 16. valve sealing ring b62784 / 3 01 no. 17. valve sealing ring b63323 / 2 01 no. 18. knorr k ring 459356 01 no. 19. knorr k ring 462581 01 no. 20. knorr k ring 465924 01 no. 21. diaphragm b82200 01 no. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 240.00 set ajmer , nwr , overhauling kit for brake cylinder to kbi part no. 170191 / 704w and 170191 / 304w ( earlier design ) and 1182515 / 704 lp and 1182515 / 304 lp ( current design ) for lhb coaches cons isting of 20 items ( 1 ) shaft sealing ring part no. b25145 / 21 qty. 01 nos. ( 2 ) spring washer part no. b26669 qty 07 nos. ( 3 ) o ring part no. b30779 qty.01 nos. ( 4 ) hose clamp part no. b33793 / 2 qty. 01 nos. ( 5 ) hose clamp part no. b33793 / 6 qty. 01 ( 6 ) hose clamp b33793 / 8 qty. 01 nos. ( 7 ) washer b53267 / a qty. 01 nos. ( 8 ) fastening wire part no. b61190 / 4 qty. 01 nos. ( 9 ) machine screw part no. b65557|4 qty. 01 nos. ( 10 ) protective cap part no. b75404 qty. 01 nos. ( 11 ) snap ring part no. 462767 qty. 02 nos. ( 12 ) clamping pin part no. 463250 qty. 01 nos. ( 13 ) lock washer part no. 465121 qty. 01 nos ( 14 ) colar part no. b38079 qty. 01 nos. ( 15 ) locking ring part no. 466031 qty. 01 nos ( 16 ) clamping pin part no. 466250 qty. 01 nos. ( 17 ) thurstin bearing needle part no. b23166466 qty. 01 nos. 18 ) breather plug part no. b66529 / 5 qty. 01 nos. ( 19 ) washer part no. b43640 qty. 01 nos. ( 20 ) bellow part no. b65580 / 12 qty. 01 nos. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 200.00 set ajmer , nwr , overhauling kit for cock dh7 for lhb coaches to kbi part no. 188738 consisting of 06 items. ( 1 ) retaining ring. 457709 qty 1 no. ( 2 ) knorr k ring. 462575 qty 2 nos. ( 3 ) o ring, a47412 qty 1 no. ( 4 ) o ring, a95468 qty 1 no. ( 5 ) o ring, k 4140 qty 3 nos. ( 6 ) valve seat bushing, c 170298, qty1 no special terms & conditions: guarantee / warranty 36 months from the date of delivery or 24 months from the date of placing in service whichever is earlier [ warranty period: 30 months after the date of delivery ] page 5 of 11 run date / time: 08 / 02 / 2023 16:15:58stores / north western rly tender document , over hauling kit for cock ahb to kbi parts no wbahb230aa002 for air brake system of lhb coachess consisting of 09 items. ( 1 ) gasket part no. wb419137a qtyiset. 02 nos ( 2 ) springpart no. wb409906 qty / set. 01 no. ( 3 ) shaft sealing ring part no. w4082704a qty / set. 01 no. ( 4 ) oring part no.or022000 qty / set. 02 nos. ( 5 ) 0 ring part n0. b76832 qty / set. 01 no. ( 6 ) 0 ring partno a78503 qty / set. 01 no. ( 7 ) o ring part no oro10000 qty / set. 01no. ( 8 ) 0 ring part no b72767qty / set. o3 nos. ( 9 ) 0 ring part no or123000 qty / set. 01 no [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 480.00 set ajmer , nwr , overhauling kit for filter to kbi part no. wbfil100aa002 for air brake system of lhb coaches consisting of 03 items. ( 1 ) o ring part no. b76832 qty / set 01 no. ( 2 ) o ring part no.b72767 qty. / set 02 nos. ( 3 ) retaining ring part no. 468861 qty. / set 01 no. special terms &conditions: guarantee / warranty 36 months from the date of delivery or 24 months from the date of delivery or 24 months from the date of placing in service whichever is earlier [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 301.00 set , cock dh 7te lhb knorr bremse part no. 188738 drg.no. b 80866 kb [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 25.00 numbers , overhauling kit for indicator to kbi part no. 148102 / w for lhb coaches consisting of 02 items. ( 1 ) plastic cover part no. c107249 qty / set 01 nos. ( 2 ) k. ring part no. 457353 qty / set 01 nos. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 408.00 set ajmer , nwr , cock ahb 200 nw 19 ( lhb ) rcf drg no.wb.415503 za & kbi part no. wbahb230aa002 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 23.00 numbers ajmer , nwr , kit for emergency brake valve nb12 kbi part no. 194023 / ki consisting 8 items, ( 1 ) o ring a27763 / 22=1no ( 2 ) o ring a93706=1no ( 3 ) o ring b90075=1no ( 4 ) knorr k ring 461627=1no ( 5 ) knorr k ring 461794=1no ( 6 ) hexagon nut 468825=1no ( 7 ) retaining ring 463775=1no ( 8 ) locking ring 466031=4no. [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 60.00 set ajmer , nwr , dump valve connector kbi part no n.62148 / 10000 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 48.00 numbers , set of connector kbi part no. stn 30979 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 4.00 set , test connection k 1e knorr bremse part no. 179470 / 07k [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 9.00 numbers , poh kit for kbi make emergency brake cable box for lhb coaches consisting 7 items. ( 1 ) kbi part no. b73364 / 3. description valve head qty / set 01 ( 2 ) kbi part no. 455588. description lock washer qty / set 01 ( 3 ) kbi part no. 456790. description clamping pin, qty / set 01 ( 4 ) kbi part no. 459143. description clamping pin, qty / set02 ( 5 ) kbi part no. 461043. description lock washer, qty / set 01 ( 6 ) kbi part no. 461664. description toothed washer, qty / set 02 ( 7 ) kbi part no. 465632. description spring, qty / set 01 [ warranty period: 30 months after the date of delivery ] carriage stores depot rajasthan 35.00 set ajmer , nwr , kit for brake caliper without brake cylider consisting 19 items ( 1 ) bush kbi part no. c101877 qty 02 set, ( 2 ) washer kbi part no. b58532 / 9 qty 2 set, ( 3 ) bush kbi part no. c101892 / 2 qty 02 set, ( 4 ) bush kbi part no. c80809 / 13 qty 02 set, ( 5 ) flanged bush kbi part no. c81080 / 14 qty 04 set, ( 6 ) hexagon nut kbi part no. 469548 qty 02 set ( 7 ) hose clamp kbi part no. b33793 / 20 qty 02 set ( 8 ) clamp ring kbi part no. c146738 / 4 qty 02 set ( 9 ) apron kbi part no. c112059 / 4 qty 02 set ( 10 ) threaded rod kbi part no. c58819 qty 04 set ( 11 ) hexagon nut kbi part no. c20308 / 13 qty 04 set ( 12 ) washer kbi part no. c84536 / 25 qty 04 set ( 13 ) pin kbi part no. c22894 / 2 qty 02 set ( 14 ) locking gate kbi part no. c77932 qty 02 set ( 15 ) locking spring c66859 qty 02 set ( 16 ) pivot screw kbi part no. c51515 / 01 qty 04 set ( 17 ) locking ring kbi part no. 466572 qty 04 set ( 18 ) clamping pin kbi part no. 462523 qty 02 set ( 19 ) bush kbi part no. b33096 / 03212 qty 08 set [ warranty period: 30 months after the date of delivery ] page 7 of 11 run date / time: 08 / 02 / 2023 16:15:58stores / north western rly tender document...

Ministry Of Mines - Rajasthan

36025079 bids are invited for t06 thrust bearing (q3) , t08 thrust bearing (q3) , 6309 ball bearing (q3) , 51115 thrust ball bearing (q3) mse total quantity : 70...

Ministry Of Mines - Rajasthan

35877952 bids are invited for t6 bearing (q3) , t8 bearing (q3) , ball bearing 3210 (q3) , thrust bearing 51113 (q3) , thrust bearing 51115 (q3) , bearing 6309 (q3) mse total quantity : 74...

Ministry Of Agriculture - Rajasthan

35859084 bids are invited for kartar 4400 combine spare parts kk010100004 double finger 2 s1010100101 knife strip 3 kk010101101 upper disc r 4 kk010101102 upper disc l 5 s0401124 chuck nut m32x1.5 6 kk010103006 prong bush 7 kk010103012 prong 8 kk010103011 prong shaft bush 9 s01010103004 prong shaft 10 s1501021 link chain 11 kk01015001 reel frame 12 kk010105003 spring tine 13 kk010105006 nylon bush 14 kk010105005 nylon bush half 15 s1010105001 ree tube assembly 16 kk010107019 strip holder assy with nut 17 kk010108016 holder assly 18 kk010108101 lower disc r 19 kk010108102 lower disc l 20 kk010108014 ball pin 21 kk010108014 ball strip 22 s0207153 hex head screw m8x20 23 s1501003 chain feeder conveyer / fitting chain set 24 s1010200005 feeder angle 25 kk010201003 coupling slip clutch 26 kk010201004 slip clutch assy 27 kk010201002 bearing carrier 28 kk01500013 castle nut size m28x 15 29 kk010201012 sprocket z 10 30 kk010201013 sprocket z 10 31 kk01307003 gun metal bush 32 kk010307023 slotted nut m32x1.5 33 kk010307002 pivot pin 34 s0606011 thrust bearing t 144 35 kk010307006 gun metal bush 36 kk010307008 o ring 37 kk010307009 ring plate 38 s0802001 internal circlip b 35 39 kk010307021 tie rod end lh 40 kk010307022 tie rod end rh 41 kk010107021 castle nut size m18x15 42 kk010105023 flat pulley 43 kk010307010 steering arm l 44 kk010307011 steering arm r 45 kk010405022 brake leather 46 s1010500002 rasp bar rh 47 s1010500003 rasp bar lh 48 kk010500009 coiled spring 49 s0201251 hex head bolt m12x40 50 kk010502003 flat idle pulley 51 kk010700007 coupling 52 s0602032 ball bearing 6309 z 53 kk010700102 guide bush 54 kk010900008 bush hsg 55 kk010900006 pivot pin 56 kk010900007 rubber bush big 57 kk010901009 lever 58 s0602022 ball bearing 6207 z 59 s1010903001 adjustable slieve top 47 / 5 inch x 55 inch 60 s1010903002 adjustable slieve bottom 61 s1010903003 adjustable slieve rear 62 kk011000003 wooden bearing 63 kk011000009 supporting bracket 64 s1011000001 crankshaft rear 65 s1011000002 crankshaft front 66 kk0111022002 guide rail 67 s1502002 elevator chain 38 pad 68 kk011102002 elevator chain 37 pad 69 s1501023 link chain 70 kk011102014 back plate 71 kk011102013 elevator cleaning pad 72 kk011107004 drive auger 73 kk01140010 suction hose 74 kk011402007 steering wheel...

Military Engineer Services - Rajasthan

35497691 tender for repair / maintenance of pump sets, submersible pump sets, s / d starters and connected items in zone iii area under age e / m of ge jaipur supply , laying, jointing, testing & commissioning in repair lt under ground cable xlpe insulated, screened pvc bedded, galvanised steel strips or wire armoured, heavy duty with multi stranded aluminium conductor, 1100 volts grade ( isi marked ) laid in trenches, ducts, pipes or fixed on poler of size 16sqmm 4 core complete all as specified and directed. including taking down old unserviceable cable. 2 supply , laying, jointing, testing & commissioning in repair lt under ground cable xlpe insulated, screened pvc bedded, galvanised steel strips or wire armoured, heavy duty with multi stranded aluminium conductor, 1100 volts grade ( isi marked ) laid in trenches, ducts, pipes or fixed on poler of size 25 sqmm 3 ½ core complete all as specified and directed. including taking down old unserviceable cable. 3 supply , laying, jointing, testing & commissioning in repair lt under ground cable xlpe insulated, screened pvc bedded, galvanised steel strips or wire armoured, heavy duty with multi stranded aluminium conductor, 1100 volts grade ( isi marked ) laid in trenches, ducts, pipes or fixed on poler of size 35 sqmm 3 ½ core complete all as specified and directed. including taking down old unserviceable cable. 4 supply , laying, jointing, testing & commissioning in repair lt under ground cable xlpe insulated, screened pvc bedded, galvanised steel strips or wire armoured, heavy duty with multi stranded aluminium conductor, 1100 volts grade ( isi marked ) laid in trenches, ducts, pipes or fixed on poler of size 95 sqmm 3 ½ core complete all as specified and directed. including taking down old unserviceable cable. 5 m & l for lifting out submersible pump set ofcapacity 10 hp to 20 hp, 1 / 3 phase, 230 / 415 volts, 50hz, ac supply along with column pipe of any size from the bore well after disconnecting electric connection, dismantling of pump and motor for repairing / replacing defective parts as ordered, oiling, greasing as required and re assembling and testing including replacing worn out nuts, bolts, washers complete and lowering the same after repairing and making electrical and delivery pipe connections complete all as specified and directed.note : ( i ) the spare part required for replacement shall be measured & paid for separately as supply only under respective items. 6 supply only, stainless steel pumpshaft. 7 supply only, gun metal impeller with neck key, distance bush. 8 supply only shaft bush. 9 supply only thrust bearing with plate of pump make : aroma / ksb or equivalent as approved by ge 10 supply only rubber gasket 3mm thick for upto 3 dia pipe flanged joint. 11 supply only shaft coupling with key. 12 supply only steel sleave for submersible cable. 13 cutting of burnt winding and rewinding the stator with supper enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles etc. 14 preparation of old paintedsteel surface of pump and motor and applying two coats of synthetic enameled paint after applying one coat of red oxide primer 15 surfaceexcavation not exceding 30 cm deep in hard and dense soil andaveraging 15 cm deepand gettingoutgreen vegetation, roots, bushes, etc surrounding ofpumphouse, cutting anxious green growth / vegetation growth for cleaning out the area around oh tank / pump house at ground levelby cutting up root, un wanted plants / trees bushes and removal the same to a distancenot less than 50 mtr complete all as specified and directed. by engineer in charge. note : the area shall be maintained from commencement of contract to completion date and paind at once only 16 m&l for pcc ( 1:3:6 ) type c1 using 20 mm graded aggregate for making good the disturbed portion of road / floor / platform etc including form work andcompaction etc completeall as specfied and directed . 17 m&l for bricks for protection cover to under ground cable ( with old size sub class b bricks ) laid flat abutting each other wth width of protection being rqual to length of bricks. the gap between adjacent bricks shall not exceeding 10mm complete all as specified and directed. 18 excavationin trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft / loose soil including trimming of tree roots in trenches complete all as specified. 19 returning, filling in, including spreading, watering and well ramming in layers notexceeding 25 cm thick each, in soft / loose soil complete all as specified. 20 removing excavated surplus soil to a distance not exceeding50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified. 21 m & l sand cushioning to pvc under ground cable with screened and washed tibba sand ( non cohessive ) and punning to provide a required cover complete all as specified and directed. note :punned thickness shall only be measured for payment. 22 supply and fix in repair dol starter, 7.5 hp suitable for 3 phase, 415 volts ac supply motorcomplete all as specified and directed. 23 supply and fix in repair of fullyautomatic star delta starter 10 hp comprising of combo volt andammeter single phase preventor, over load relayand timer housed in ms sheet power coated enclosure of 10 hp capacity complete all as specified and directed. 24 supply and fix in repair of fullyautomatic star delta starter suitable for 12.5 to 20 hp comprising of combo volt andammeter single phase preventor, over load relayand timer housed in ms sheet power coated enclosuresuitable for 12.5 to 20 hp capacity complete all as specified and directed. 25 supply and fix in repair of fullyautomatic star delta starter 25 hp comprising of combo volt andammeter single phase preventor, over load relayand timer housed in ms sheet power coated enclosure suitable for operating 25 hp centrifugal pumpset complete all as specified and directed. 26 supply and fix in repair of fullyautomatic star delta starter comprising of combo volt andammeter single phase preventor, over load relayand timer housed in ms sheet power coated enclosure suitable for operating up to 30 to 35 hp centrifugal pumpset complete all as specified and directed. 27 supply and fix in repair of fullyautomatic star delta starter comprising of combo volt andammeter single phase preventor, over load relayand timer housed in ms sheet power coated enclosure suitable for operating up to 40 hp to 50 hp centrifugal pumpset complete all as specified and directed. 28 supply and fix in repair of fullyautomatic star delta starter comprising of combo volt andammeter single phase preventor, over load relayand timer housed in ms sheet power coated enclosure suitable for operating 55 hp to 75 hp centrifugal pumpset complete all as specified and directed. 29 s&f in repair fullyautomatic star delta starter comprising ofline contactor, bypass contactor and semiconductor fuse of capacity up to centrifugal pump 17.5 hp set complete all as specified and directed. 30 s&f in repair fullyautomatic star delta starter comprising ofline contactor, bypass contactor and semiconductor fuse of capacity up to centrifugal pump 40 hp set complete all as specified and directed. 31 s&f in repair fullyautomatic star delta starter comprising ofline contactor, bypass contactor and semiconductor fuse of capacity up to centrifugal pump 60 hp set complete all as specified and directed. 32 s&f in repair copper cablemultistranded conductor unarmoured16 sqmm single core 1100 v grade pvc insulated sheathed along with copper lugs complete all as specified and directed. 33 s&f in repair copper cablemultistranded conductor unarmoured25 sqmm single core 1100 v grade pvc insulated sheathed along with copper lugs complete all as specified and directed. 34 supply and fix in repair mccb tpn 63 amp to 100 amp , 415 volts, 50 hz 35ka complete all as specified and directed. 35 supply and fix in repair mccb tpn 200 amp , 415 volts, 50 hz 35ka complete all as specified and directed. 36 supply and fix in repair mccb tpn 250 amp , 415 volts, 50 hz 35ka complete all as specified and directed. 37 supply and fix in repair mccb tpn 400 amp , 415 volts, 50 hz 35ka complete all as specified and directed. 38 m & l for transporataion & dismanteling of mono block, fountain pump set any type cap upto 10 hp, 1 or 3 phase, 415 volts, 50hz, ac supplyafter disconnecting electric connection, dismanteling of pump for repairing / replacing defective parts as ordered, oiling & greasing, re assembling and testing including replacing worn out nuts, bolts, washers complete and refixing the same and reconnecting to pipe line and electric connection after following repairs as directed : note : ( i ) the spare part required for replacement shall be measured & paid for separately as supply only under corresponding items 39 supply only cable clamp including grommet for cable connection of motor. 40 supply only ball bearing as per existing. 41 supply only, stainless steel pumpshaft. 42 supply only, cast iron impeller with lock nut and washer. 43 supply only oil seal with oil seal cup as per existing. 44 supply only ss counter for bearing thrust load as per existing 45 supply only delivery flange wahser as per existing. 46 supply only foot valve made of ms / pvc as per existing. 47 cutting of burnt winding and rewinding the stator with pvc insulated copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles etc. complete all as directed. 48 preparation of old paintedsteel surface of pump and motor and applying two coats of synthetic enameled paint after applying one coat of red oxide primer. 49 m & l for transporattaion & dismanteling of centerifugal pump set of cap 5 to 12.5 hp 3 phase, 415 volts, 50hz, ac supplyafter disconnecting electric connection, dismanteling of pump for repairing / replacing defective parts as ordered, oiling and greasing, re assembling and testing including replacing worn out nuts, bolts, washers complete and refixing the same and reconnecting to pipe line and electric connection after following repairs as directed by engineer in charge : note : ( i ) the spare part required for replacement shall be measured & paid for separately as supply only under repective items 50 supply only terminal box including connectors of copper, plate of motor. 51 supply only ball bearing as per existing. 52 supply only, stainless steel pumpshaft. 53 supply only, gun metal impeller with neck key, distance bush. 54 supply only mettalic coupling with cover as per existing. 55 supply only damaged ms love joint star rubber disc for coupling as per existing 56 supply only rubber gasket 3mm thick for flange joints as per existing 57 supply only fan blade ( pvc / mettalic ) as per existing. 58 cutting of burnt winding and rewinding the stator with super enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles etc. complete all as directed. 59 preparation of old paintedsteel surface of pump and motor and applying two coats of synthetic enameled paint after applying one coat of red oxide primer. 60 m & l for transporattaion & dismanteling of centerifugal pump set of cap 15 to 30 hp 3 phase, 415 volts, 50hz, ac supplyafter disconnecting electric connection, dismanteling of pump for repairing / replacing defective parts as ordered, oiling and greasing re assembling and testing including replacing worn out nuts, bolts, washers complete and refixing the same and reconnecting to pipe line and electric connection after following repairs as directed by engineer in charge : note : ( i ) the spare part required for replacement shall be measured & paid for separately as supply only under respective items 61 supply only terminal box including connectors of copper, plate of motor. 62 supply only ball bearing as per existing. 63 supply only, stainless steel pumpshaft. 64 supply only, gun metal impeller with neck key, distance bush. 65 supply only coupling with cover as per existing. 66 supply only damaged ms love joint star rubber disc as per existing 67 supply only fan blade as per existing. 68 supply only steel pipe for watering the gland packing as per existing 69 supply only base stand for motor with new nut, bolt & washers as per existing 70 cutting of burnt winding and rewinding the stator with supper enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles etc. complete all as specified and directed. 71 preparation of old paintedsteel surface of pump and motor and applying two coats of synthetic enameled paint after applying one coat of red oxide primer. 72 supply only rotor for motor as per existing. 73 m & l for transporattaion & dismanteling of centerifugal pump set of cap 40 to 75 hp 3 phase, 415 volts, 50hz, ac supplyafter disconnecting electric connection, dismanteling of pump for repairing / replacing defective parts as ordered, oiling & greasing, re assembling and testing including replacing worn out nuts, bolts, washers complete and refixing the same and reconnecting to pipe line and electric connection after following repairs as directed by engineer in charge : note : ( i ) the spare part required for replacement shall be measured & paid for separately as supply only under respective items 74 supply only terminal box including connectors of copper, plate of motor. 75 supply only ball bearing as per existing. 76 supply only, stainless steel pumpshaft. 77 supply only, gun metal impeller with neck key, distance bush. 78 supply only coupling with cover as per existing. 79 supply only damaged ms love joint star rubber disc as per existing 80 supply only rubber gasket 3mm thick for flange joints as per existing 81 supply only fan blade as per existing. 82 supply only base stand for motor with new nut, bolt & washers as per existing 83 cutting of burnt winding and rewinding the stator with supper enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles etc. complete all as specified and directed. 84 preparation of old paintedsteel surface of pump and motor and applying two coats of synthetic enameled paint after applying one coat of red oxide primer. 85 supply only rotor for motor as per existing 86 m & l taking out submersible pump set of capacity 3 hp to 7.5 hp, 1 / 3 phase, 230 / 415 volts, 50hz, ac supply along with column pipe of any size from the bore well after disconnecting electric connection, dismantling of pump and motor for repairing / replacing defective parts as ordered, oiling, greasing as required and re assembling and testing including replacing worn out nuts, bolts, washers complete and refixing the same after repairing and making electrical and delivery pipe connections complete all as specified and directed.note : ( i ) the spare part required for replacement shall be measured & paid for separately as supply only under respective items 87 supply only, stainless steel pumpshaft. 88 supply only, gun metal impeller with neck key, distance bush. 89 supply only shaft bush. 90 supply only thrust bearing with plate of pump. 91 supply only rubber gasket 3mm thick having 4 nos of 5 / 8 dia hole. 92 supply only shaft coupling with key. 93 supply only steel sleave for submersible cable. 94 cutting of burnt winding and rewinding the stator with pvc insulated copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles etc. complete all as directed. 95 preparation of old paintedsteel surface of pump and motor and applying two coats of synthetic enameled paint after applying one coat of red oxide primer 96 supply & fixcablejointingkitfor 1.1 kv grade cablefor straight throughjointcompletewithjointingmaterial andaccessories including necessary earth work suitablefor 3.5 core xlpe / pvcarmouredai conductorcableoffollowing sizes : 25 sqmm to 95 sqmm 97 all as per item no. 34 above but of size 120 sqmm to 185 sqmm 98 m&l for re wiring of the complete starter panel main switch to starter and connected accessories withcopper conductor pvc insulated wire of existing suitable size ( upto 4 sqmm and maximum 20 mtr ) including cable lugs complete all as specified and directed. 99 supply & fixin repair contactor of capacity 100 amp, 4 pole, as per existing.complete all as specified and directed. 100 supply & fixin repair contactor of capacity 200 amp, 3 pole, typeas per existing.complete all as specified and directed. 101 supply & fix in repair electronic timer as per existing. 102 supply & fix in replacement micro processer relay 8 amp to 40 amp as per existing. 103 supply & fixin repair single phase preventor for the motors upto capacity 60 hpas per existing complete all as specified and directed. 104 supply & fixin repair ampere meter with ct, s of range 0 30 amps as per existing complete all as specified and directed. 105 supply & fixin repair voltmeter with pt, s of range 0 500 volts as per existing complete all as specified and directed. 106 supply & fixin repair selector switch for voltmeter / ampere meter as per existing. 107 supply & fixin repair over load relay coil 37 50 amp, 230 volts type rt23vas per existing complete all as specified and directed. 108 supply & fix in repair existing pannel box upto size 1.2 x 0.4x1.5mtr with new copperbus bar ( upto 10 kg ) suitable for existing fittings / fixtures complete all as specified and directed. 109 supply & fix in repair mcb tp of capacity 20 63 amps, rating 10 / 15 ka415 volts as per existing complete all as specified and directed. 110 s&f in repair gland packing to thevalves / pump setc. of any sizes / capacity complete with neoprene rubber gasket, jointing material and incl nuts / bolts / washer of suitable size etc complete all as specified and directed. 111 replacing old u / s ms nuts, bolts with washer of any size / type. 112 material and labour for cutting of bituminous road or any type of floor for laying of pipe / cables not exceeding 1.5 meter wide and not exceeding 1.5meterdeep including refilling / with material and, watering well ramming / compacting and making good with pcc 1;2;4, type b 1, 100mm thick complete all as specified anddirected. 113 s&f in repairof following sizecolumn pipe both side flanged gi medium grade isi marked ( each of 3 m length ) including taking out old corroded column pipe both side flanged complete all as specified and directed. ( i ) 80 mm bore 114 ( ii ) 65 mm bore 115 ( iii ) 50 mm bore 116 supply and fix jointing kit for submersible cable of 1100 volts grade of 4 / 6 sqmm 3 core , complete all as specified and directed. 117 supply & fix in repair submersible copper cable pvc insulated over all sheethed flat isi marked of 1100 volts grade of 4 sqmm 3 core. 118 supply & fix in repair submersible copper cable pvc insulated over all sheethed flat isi marked of 1100 volts grade of 6 sqmm 3 core. 119 disconnecting and taking outexisitng lt over heated or burnt cable terminal / joint atpanel / fidder piller & unserviciable portion oflt cable of any size , after thatstretching / opening cable to suitable required length etc and fixing aluminium lugs / joint material and suitablenuts bolts & washeretc complete all as specified and directed 120 dismanteling of pressure pump set of cap 0.75 to 01hp , 1 or 3 phase, 415 volts, 50hz, ac supplyafter disconnecting electric connection, repairing / replacing defective parts as ordered, re assembling and testing including replacing worn out nuts, bolts, washers completeand electric connection after following repairs as directednote : ( i ) the spare part required for replacement shall be measured & paid for separately as supply only under respective items 121 supply only ball bearing as per existing. make: nbc / skf or equivalent as approved by ge 122 cutting of burnt winding and rewinding the stator with supper enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles etc. 123 preparation of old paintedsteel surface ofpressure pump and applying two coats of synthetic enameled paint after applying one coat of red oxide primer. 124 supply and spray of chemicalfor unwanted wild grass by spray machine etc complete all as directed by engr in charge. make : glyphosate ( 41 sl ) or eqivalent as approved by ge 125 s&f in repair changeover switch 100 amp , 415 volts, 4 pole on load without sheet enclouser suitable for existing panel complete all as specified and directed. 126 m&l for development of tube well with compressed air and after with 25% extra capacity pump by pumping muddy water complete all as specified and directed. 127 s&f in repair of ci foot valve isi marked with all fittings of following sizes: ( i ) 150 mm dia 128 ( ii ) 100 mm dia 129 ( iii ) 80 mm dia 130 ( iv ) 50 mm bore 131 supply calcium based high strength granular chlorination chemical ( calcium hypochlorite having chlorine 65% to 70% ) for water treatment. granular material shall be free of foreign material decomposing at 177 c soluble in water and alcohol not hygroscopic practically clear in water solution at saturation level. the material should not contain more than 5% to 10% moisture. granular size should be as follws : mesh passing through 100 bss 1.5% maximum iron as fe 0.05% maximum mn 40 ppm maximum mol wt 142.98, toxicity :oral rate ld 50 850 mg / kg. duly tested from approved laboratory packed in a fibre drum duly sealed granular type from manufacturer or authorised dealer / distributor complete all as specified and directed. note brand name / batch number and complete pariculars of manufacturer should be printed on the container / packing. make: m / s sree rayalaseema hi strength hypo ltd ( puri chlor brand calcium hypo chlorite ) or any make approved by e in cs branch. 132 supply only bleaching powder grade i havin chloring content 35% dry and white free flowing powder without hard lumps and impurities and easily soluble in water. the material should not contain more thatn 0.3% moisture particle size passing through 1.70 mm is sieve and stability loss of chlorine should be maximum 1 / 15th. make: as approved by e in cs branch....

Rajasthan State Ganganagar Sugar Mills Limited - Rajasthan

35074535 rate contract for spare parts of semi automatic bottling machines 1 level control rubber washer assoited size 2 sponge washer black 3 nozzle inner washer ( for s.s. m / c ) flat 4 o ring ( for s.s. m / c ) ( assoited size ) 5 s.s. nozzle outer and inner set 28 mm complete ( for s.s. & engineers india m / c ) 6 teflon nozzle outer and inner set 28 mm complete ( for engineers india / s.s. make m / c ) 7 n.r.v. complete set for ( for s.s. m / c ) 8 n.r.v. complete set for ( for engineer india make m / c ) 9 glass tube indicator for ( for engineer india mane m / c ) 10 three way valve for filling m / c 11 filling m / c belt ( b 32 ) 12 vacuum pump oil level indicator 3 mm thick 13 vacuum pump rotor blade 14 vacuum pump oil seal 15 vacuum pump filter with nipple ( brass ) 16 three way valve teflon washer, 17 theard roller 18 skrit roller 19 skrit roller washer / spring / lock 20 theard roller spring / lock 21 thrust bearing 22 arm set four pin complete with roller etc. 23 planzer for adjust of roller 24 side cam roller complete set 25 side cam roller nut / bolt only 26 side cam arm set complete with spiring 27 side cam arm tension spring 28 clamping spring 29 taper pin 30 head return spring 31 base pressure spring ( for s.s. make ) 32 base pressure spring ( for engineers india 33 leading screw complete with cheak nut 34 pressure noze 28 mm ( for s.s. make ) 35 pressure noze 25 mm ( for s.s. make ) 36 pressure noze 28 mm ( for engineers india ) 37 pressure noze 25 mm ( for engineers india ) 38 6x6 gurev screw 39 5 / 16x1 allan bolt 40 wavell pinion gun metal ( 30 teeth ) 41 l key wavell pinion suitable for ssp / ee machine 42 closing camp brass bush gun metal 43 wavell pinion guide screw 44 oil cap 45 rubber pad 46 bottle guide with nut ( aluminum ) 47 gear box bush with key ( for s.s. make ) 48 gear box shaft 49 gear box 12 teeth gear tempered with shaft and keys 50 gear box 72 teeth gear 51 gear box 88 teeth gear 52 pressure plat only with nut and bolt 53 sprocket 21 teeth gear black ( for s.s. make m / c ) 54 sprocket 19 teeth with bearing ( for engineers india make m / c 55 sprocket 19 teeth without bearing ( for engineers india make m / c 56 bearing uc 205 with cover 57 bearing uc 206 with cover 58 bearing 6205 59 z type green strip suitable for ssp / ee ( per feet ) 60 chain adjuster nut bolt 61 chain adjuster complete set with bracket and nut / bolt 62 slat chain nylon roller ( ssp / ee ) 63 idler nylon roller for single slat chain ( ssp / ee ) 64 double slat chain 21 teeth sprocket mounting shaft with keys ( ssp ) 65 slat chain nylon polly mounting shaft ( ssp / ee ) 66 variator set complete ( gear box+ variator+2hp motor ) 67 side plate ss flat with green strip complete ( per feet ) 68 40 teeth bronze gear for ( greaves gear box ) ee 69 transfer plate ( ssp / ee ) 70 bearing 6006 dz 71 comb for packing belt 12 wide 35 no. 72 packing belt gear box adjuster pulley 73 packing belt patta 12 wide 5 mm thick, 5 ply nylon / cloth ( per feet ) 74 packing belt roller ( nylon ) 75 filter pad / filter cloth 76 rubber for aluminum roller 77 adjuster rubber 78 chain timing with naka 79 aluminum roller 80 assorted size for ssp machine 81 finger for label gumming m / c 82 nozzle for rinser m / c ( engineer india & s.s. make m / c ) 83 pocket ( bottle holder ) for engineer india make m / c ) 84 teflon disc for engineers indin make m / c 85 massage press plate 5 wide x 68 length of auto wet glue labeling machine 86 pressure belt 1 wide x 40 length of auto wet glue labeling machine 87 foam space l 25 x w 5 for auto wet glue labeling machine 88 bearing 6205 89 bearing 6206 90 bearing 6208 91 chamber bearing 6907 92 magzine finger for auto wet glue labeling machine ( 8 set ) 93 male / female of pick up cylinder for auto labeling machine ( 16 set ) 94 pick up cylinder can ( 8 set ) for auto labeling machine 95 pick up cylinder finger ( 8 set ) for auto labeling machine 96 master ( 55x60 ) mm ( w x l ) for auto labeling machine 97 chain gear box for wet glue labeling machine 98 warm gear box for wet glue labeling machine 99 warm set for wet glue labeling machine 100 oil seal 35 72 10 101 oil seal 50 80 10 102 oil seal 50 60 10 103 oil seal 55 vfd 1.5 kw ( schneider ) / siemers / deata 104 relay 24 vdc ( omron / bch ) 105 power supply 24 vbc 4.5 amp ( smps ) 106 vfd variator panel complete for slat chain drive 107 100 ltr ( s.s. 304 ) tank complete for vaccum firing machine ( 6 head+8 head ) 108 massage press plate 5 wide x 68 length of auto wet glue labeling machine...

Rajasthan State Road Transport Corporation - Rajasthan

34997895 tender for supply of ball & tapper roller bearings specifications of ball & tapper roller bearings as:190:81:march:2014, as:322:66:jan:2004 2 2691 2620 0143 / 3125 / 3133 bb455236 fsassy. needle cage bearing 3 2691 2620 0142 / 3124 / 3130 bb728040fsassy needle cage bearing 4 2691 2630 3104 tapper roller bearing25572 25520, bs iii / 2017 5 p4900402 / mub 7307 / jc 8035tail pinion bearing bs ii 6 2576 3340 3103tapper roller bearing32308 bs iv / frt hub outer bearing bs iii / 2017 7 f0242510 / f0254010 spigot bearing 8 f0243010 / f0254610 needle roller bearing 1st 9 f0242710 / f0254910needle roller bearingbb44545fs 10 f0243110 / f0254710 2691 2620 3106needle rollerbearing 1st bb627040 11 f0242410 / f0259310 roller bearing ( nup 309em ) 12 f0248510 / f0254510 taper rollerbearing ( 2789 2729 ) 13 p4900202 diff. pinion bearing ( 493 497 ) 14 f0259210 / jc 8020cyl. roller bearing ips 15 f0246010tapper bearing ( 567 563 ) 16 6201 2rsalternator bearing tc 17 mb563234ps center bearing eicher ( tx 7240 ) 18 f0253810clutch release brg.ley. bs iii ( 6212 lu ) 19 ib001825 needle bearing 3rd ( b60049 ) 20 ib001824 needle bearing 1st ( b60047 ) 21 ib001826 needle bearing reverse ( b60048 ) 22 ib003070pilot bearing m / s eicher midi 23 if000148 / bb60063needle bearing 4th eicher midi 24 if000864 / nup307 mnrneedle bearing c / s 25 if000863 / nup307 mnneedle bearing c / s 26 id200359 / jc 8022bearing 27 id200480 / bb60107needle roller bearing 1st 28 id200456 / bb60109needle roller bearing 2nd 29 id200349 / b60106needle roller bearing reverse 30 2691 2620 3103 / tapper roller bearing 28580 / 521 bs iii / 2017 / 2013 31 2516 2635 3104roller ring ( rev idler gear ) 32 id200457bearing 3rd speed 33 id200458bearing 4th speed 34 id200453bearing drive pinion 35 2691 2625 3113roller thrust bearing arrgmtbs iii / 2017 36 f0267310bearing 6.s.850 37 f0267510bearing 6.s.850 38 f0267410n.r. bearing 39 f0256310 nr bearing 5th6.s. 850 40 f0267710input shaft bearing 41 2060 3501 3001tapper rollerbearing 31312l bs iii / 2017 42 2573 3530 3101 / 47487 / 20diff.cage bearing 43 2691 2620 3111needle cage bearing ist 44 jc 409025pinion bearing lay 45 pop00150pilot bearing r160 crb 46 hk4012 ntnbearing leyland 47 0009811201 / nu309ncyl. roller bearing 48 2505 2620 3106four point ball bearing qj309 49 2505 2620 3123double row needle cage bearing 50 2505 2620 3124double row roller cage bearing 51 2505 2630 3104t.r. bearing bs1 / 2 / 3 / 4 52 6202bearing 53 6204bearing 54 db142012pn.r. bearing...

Department Of Atomic Energy - Rajasthan

34936227 bids are invited for pumps private ltd spare o ring bell mouth part no 4250 , spare o ring casing part no 4250 1 , spare o ring rm pipe part no 4250 2 , o ring st box part no 4250 3 , spare key thrust block part no 3280 , spare impeller key part no 3200 , spare anti rotation pin part no 4221 , spare key solid muff coupling part no 3260 , spare flexible coupling ph mhpart no 4830 , spare pump bearing bush part no 2830 , spare rising main pipe intermediatepart no 1151 , spare rising main pipe bottom part no 1150 , spare lock nut part no 3011 , spare adjusting ring part no 1822 , spare ratchet pin part no 2004 , spare gland one set consisting of 2 halves part , spare loose stuffing box part no 2401 , spare bearing end cover ratchetpart no 2880 , spare thrust bearing housing part no 2882 , spare thrust block part no 2883 , spare coupling bush for flexible coupling of pump , spare intermediate bearing sleeve part no 2834 , spare casing and diffuser part no 1030 , spare solid muff coupling part no 2050 , spare split collar part no 2060 , spare impeller wearing ring de part no 1601 , spare impeller wearing ring part no 1602 , spare gland sleeve part no 2106 , spare int bush bearing bracket part no 2802 , spare rising main pipe intermediate part no 115 , spare logging lantern ring part no 2301 , spare suction bell mouth part no 4910 spare for napw pumps make ms wilo mather and platt total quantity : 148...

Indira Gandhi Canal Project Rajasthan - Rajasthan

34353365 supply of spares for various equipments etc. and sitc work at ps i to ps iv of ch. kumbha ram arya lift scheme during the year 2022 23 2 vacuum contractor unit for existing alsthom motor feeder panel ( existing vc make vc3ad400 schneider ) providing fixing testing in existing motor feeder panel 3 vacuum interrupter assembly with fixed contact ( for exixting andrewle make motor feeder panel ) providing fixing testing in existing motor feeder panel 4 motor protection relay numerical type for exixting motor feeder panels 5 master trip relay 1 element 3no +2nc 24 volt dc 6 idmt relay , 3 over currentand1 earth fault numerical protection relay auxsupply 18 230 volt ac / dc 7 isolator 7.2 kv 630a 18.4 ka on / off for existing alsthom motor feeder panel 8 24 v dc 8 way contactor compitable / matching with existing system 9 3.3 / 7.2 kv surge arrester / la ( indoor type matching with existing in lxh type slv6 compitable with exixting system 10 contactor pak 6us, 44w, 30v dc compitable with existing system 11 trip coil box assembly with plunger with coil for existing andrew yule panels 12 switch auxiliary assembly 8 way for existing andrew yule panels 13 capacitor rectifier unit 10a 600 piv 350 v940 mfd110 v ac to dc 14 copper bus bar ( a ) 50x10 mm size 15 three pole ac contactor ( cat. no. ce15gn3, size g, 40 amp, 22 kw ) for eot crane 16 earthing strip 50x5x5 17 pvc sleeve 800 amp for bus bar size 12x50mm ( mtr ) 18 6.6 / 7.2 kv indoor current transformer, ration asmention below accuracy class 1, 5p10 burden 15vaepoxy resin cast twin core with following ratioconfirmed to is 2705 ctr: 100 / 5+5 amp, str 13.1 / 1 sec ( providing fixing testing , compitable with existing system ) 19 digital power factor meter, is 722 ( 415 volt, 3phase ) is:6767 20 thrust bearing 29328e 1 21 bearing nu226 m1c3 22 bearing 7320 b 23 bearing nu232 m1c3 24 bearing 7322 b 25 thrust bearing 29324 e1 26 bearing 6232mc3 27 bearing 7326 b 28 muff coupling complete set of material ss. 410110 / 132 cusec pump 29 muff coupling complete set of material ss. 410100 cusec pump 30 muff coupling complete set of material ss. 41075 cusec pump 31 ammeter digital for 6.6 kv incomer / motor feeder panels / 33kv cr panel compitable with existing system 32 voltmeter digital for 6.6 kv incomer / motor feeder panels / 33kv cr panels compitable with existing system 33 oti for transformer ( for 500 to 7500 kva ) 34 wti for trasnsformer ( for 500 to 7500 kva ) 35 bucholz relay for transformer ( for 500 to 7500 kva ) 36 tnc switch...

North Western Railway - Rajasthan

34224033 supply of set of items for 35 ton jackset of items for 35 ton jack, set of items for 35 ton jack. ( a ) supply and fitment for main load screw of 96 mm dia. for navyug make 35 ton jack. material en9 , ( b ) supply and fitment of top nut, thrust bearing packing, bronze nut with housing for navyug make 35 ton jack...

Medical And Health Services - Rajasthan

34206683 construction of shc bejpur block itawa distt. kota 1 clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 2 earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms, lift upto 1.5 mtr. including taking out the excavated soil and depositing and refilling of jhiri with watering and ramming and disposal of surplus excavated soil as directed within a lead of 50 mtr. all kinds of soil 3 filling in plinth with locally available river shingle under floors including watering ramming consolidating and dressing complete including cost of shingle sand. 4 providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering all work up to plinth level.1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). 5 centering and shuttering with plywood or steel plate including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. 6 providing and laying in position specified grade ofcement concrete forall rcc structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement.m20 grade nominal 7 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.m20 grade nominal mix 8 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for :columns, pillars, posts and struts etc. 9 centering & shuttering with plywood or steel plate including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor three level for :suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 10 random rubble stone masonry for foundation and plinth in cement sand mortar above 30 cm thick wall in :cement mortar 1 : 6 (1 cement : 6 sand). 11 providing and laying in position specified grade ofcement concrete for rcc structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.m20 grade nominal mix 12 providing and fabricating reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. thermo mechanically treated bars (conforming of relevent is code) 13 filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead upto 50 mtr. and lift upto 1.5 mtr. 14 filling in plinth withlocally available good earth under floors including watering ramming consolidating and dressing complete including cost of locally available good earth 15 flyash flyash brick work with flyash flyash bricks of class designation 75 in superstructure above plinth level upto floor three level in all shapes and sizes in :cement mortar 1 : 6 (1 cement : 6 coarse sand) 16 half flyash brick masonry in superstructure , above plinth level upto floor three levelusing flyash bricks of designation 75 cement mortar 1 : 6 (1 cement : 6 coarse sand 17 random rubble dry stone kharanja under floor. 18 providing and fixing 15 to 20 mm thick granite stone slab mirror polished and machine edge cut in walls, pillars, steps, shelves, sills counters, floors etc. laid on 12 mm (av.) thick base of cement mortar 1 : 3 (1 cement : 3 coarse sand) jointing with white cement mortar 1 : 2 (1 white cement : 2 marble dust) with pigment to match the shade of the granite slab complete including rubbing and polishing of :green / black / other granite. above 3601 cm2 slabs 19 providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to is : 13753 & is :15622 of size 300mm x 450mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). 20 providing and fixing 1st quality mat finished ceremic tile size 300 x 300 mm confirming to is : 13753 colour such as white, grey, ivory, fume red brown in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (untile of roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of the complete (including the cost of cement mortor bed1:4). category a : kajaria, jhonson, somani make 21 providing & fixing vitrified paving tiles size 600 mm × 600 mm × 12 mm thick fix with cement mortar over 20 mm thich (1 cement 4 sand) laid on a bed of neat cement slurry including nicely finished joints using water proof joint filler powder (untile or roffe make) and finishing with flush pointing in white cement mixed with pigment to match the shade of tile complete (including the cost of cement mortor 1:4) category a : kajaria, jhonson, somani make 22 providing and fixing external grade board solid core single leaf flush door shutters isi 2202 67 marked using phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure a :30 mm thick commercial veneer both side 23 add extra in flush doors :for double leaf 24 for external teak wood lipping on flush door30mmx6mm 25 extra for cutting rebate in flush door shutters (total area of the shutter to be measured). 26 providing and fixing anodised aluminium curtain rod with aluminium brackets complete :25 mm dia 27 providing and fixing t iron frames for doors, windows and ventilators of mild steel tee sections, joints mitred and welded with 15 x 3 mm lugs, 10cm long embedded in cement concrete blocks 15 x 10 x 10 cm of 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 28 supply and fixing in cement mortar welded hand railing made out of ms round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or pvc hand railing to be paid extra) with priming coat of red oxide. 29 providing and fixing steel gate grating and grills made of angles, tees, square bars or other flats black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. 30 providing and fixing m.s. sheet single leaf door shutter in angle iron frame 35 x 35 x 5 mm suitabilly diagonally braced with 25 x 3 mm flat iron above and below lock rail of size 50 x 5 mm beading extra including all fittings, as per direction of engg. incharge but excluding cost of chowkhats : including two coats of anit corrasite red oxide primer paint. m.s. sheet 18 s.w.g. 31 supplying and fixing of steel windows made out (65 x 40 mm) hollow metal pressed section of 1.25 mm thick sheet f4 & f7 standard rolled section conforming to is 1038 with wholly openable shutter of 0.80 mm thick (out side & inside) opening c.r. sheet embossed panels, joints matted and flush welded with suitable hinges, steel lugs & screws with approved oxidised steel handles, fittings, peg stays (casement stays) etc. complete in all respect including providing 10 mm square m.s. bars 10 cm. c/c and applying priming coat of red oxide paint. 32 supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20 x 3 mm with suitable screw at not exceeding 150 mm distance. 33 providing batta (gola) 75 mm x 75 mm in cement concrete (1 : 2 : 4) including finishing with cement mortar 1 : 3 as per standard design. 34 providing & laying chequerred plain cement concrete embossed to specially manufactured non slipping tiles of approved make 20 mm thick laid on 20 mm thick bed of cement mortar 1 : 6 jointed with neat cement slurry complete.medium shade using approximately 50% white cement and 50% ordinary cement. 35 plaster on new surface on walls in cement sand mortar 1 : 6 including racking of joint etc. complete fine finished :25 mm thick 36 plaster on new surface on walls in cement sand mortar 1 : 6 including racking of joint etc. complete fine finished :20 mm thick 37 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand). 38 applying priming coat :with ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. 39 painting with enamel paint of approved brand and manufacture to give an even shade :two or more coats on new work. 40 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including prepration of base and all scaffolding :new work (two or more coats) over and including scrapping and priming coat with cement primer. 41 painting exterior surface ofwallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. new work 42 renewing glass panes, with putty and nails wherever necessary :4 mm thick plain glass panes. 43 supplying and fixing dressed sand or other approved stone shelves, tands in cement mortar 1 : 3 with fine dressed edges : 35 mm thick. 44 supplying and fixing in walls machine cut and polished stone shelves, tands andin cm 1:3 with machine cut edges :kota stone 25 to 30mm thick. 45 making of health wellness center patern (gola) including colour picture work in side for fascasde branding includig material labour and t & p as pe direction engineer in charge as per standared drawing/patern 46 making of border of window health wellness center as per given patern for fascasde branding includig material labour and t & p as pe direction engineer in charge up to window size 4x5.6 as per standared drawing/patern 47 extra for providing edge moulding to 15 18mm thick marble/ granite stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge.granite work / kota stonefull edge moulding 48 providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completebirla/j.k./nerolac or iso. as per direction of engineer in charge. 49 providing& fixing precast cement concrete coping 1: 2:4mix50mmthickcompleteas per specification 50 finishing with 25 mm thick cement plaster on roofs in cement sand mortar 1 : 4 mix including water proofing compound @ 2% of cement used. with neat cement, finishing, curing etc. complete in all respect including making of 300 mm x 300 mm square. 51 providing and fixing indian type white glazed vitreous china 1st quality w.c. orissa pan (is : 2556 mark) with 100 mm vitreous china p or s trap including cutting and making good the wall and floor. size 580 x 440 mm 52 p & f wvc wash basin (1st quality is : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p.pillar cock (is : 8934 mark) & 32 mm c.p. brass waste coupling of approved make, 25 mm g.i. waste pipe complete including cutting & making good the wall. size 510 mmx 400 mm 53 p & f wvc wash basin (1st quality is : 2556 mark) of approved make with c.i. brackets duly painted, 1 no. 15 mm c.p.pillar cock (is : 8934 mark) & 32 mm c.p. brass waste coupling of approved make, 25 mm g.i. waste pipe complete including cutting & making good the wall. size 550 x 400 mm dia for counter top 54 p & f kitchen & lab sink of approved make with c.i. brackets duly painted, 40 mm c.p. waste coupling, c.p. brass chain with rubber plug, 40 mm g.i. waste pipe upto floor level complete including cutting & making good the wall & floor. 1.0 mm thick salem stainless steel aisi 304 kitchen sink of approved make (nirali, neel kanth, jaina, faber, criystal ) with large waste couplings is 13983 1994 over all size bowl size(inches) (inches)24 x 18 x 8 20 x 16 x 8 55 p & f looking mirror with pvc frame of approved (atul/ equivalent)size 500 x 400 mm 56 providing and fixing towel rail or ring of approved quality / make. c.p. brass towel rail with brackets 450 x 20 mm. 57 providing and fixing soap dish or tray of approved quality / make. c.p. brass 58 providing and fixing bath shower of approved quality / make. c.p. brass of heavy & superior quality 150 mm. 59 providing & fixing c.p. flange for 15 mm dia taps 60 p & f bib cock (is: 8931 mark) superior quality of approved make c.p. brass bib cock, 15 mm nominal bore 61 providing and fixing inlet connection (angle, valves) superior quality, of approved make.for wash basin gyser etc.c.p. inlet connection 15 mm.brass (is: 8931 marked) 62 providing and fixing 15 mm dia connection pipe of approved quality / make. pvc pipe with cp brass nuts upto length 600 mm 63 providing and fixing flush cock / flush valve (is : 9758 mark) for wc of approved quality make. c p brass half turn exposed 25 mm nominal bore 64 providing and fixing full way valve (is : 778 mark) or wheel valve of approved make. gun metal 15 mm nominal bore 65 providing and fixing full way valve (is : 778 mark) or wheel valve of approved make. gun metal 25 mm nominal bore 66 providing and fixing pvc storage tank confirming to is : (12701 marked indicating the bis license no) of approved make with cover, 25 mm dia 1 m long g.i. over flow pipe & 25 cm. long wash out pipe with plug & socket, including making connection etc. complete of approved design.500 litres capacity 67 hoisting charges for each floor. 68 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. (internal work exposed on wall) 20mm nominal outer dia pipes 69 providing and fixing 3 layer pp r (polypropylene random coplymer ) pipes sdr 7.4 uv stabilized and antimicrobial fusion welded, having thermal stability for hot & cold water supply including all pp r plain & brass threaded polypropylene random fittings including trenching, refilling and testing of joint complete as per direction of engineer in charge. (external works)pn 16pipe, 32 mm od 70 providing and laying c.c. 1 : 5 :10 (stone aggregate 40 mm nominal size) upto haunches of s.w. pipes including 150 mm thick bed concrete as per rajasthan pwd specifications : (width w = dia of pipe in cm + 40 cm.) concrete width to be reduced from width w at centre of pipe to 0 at top of pipe.(excluding cost of pipe )100 mm dias.w. pipe 71 providing and fixing rigid pvc pipe (is : 4985 mark) class ii (4 kg./cm2) approved quality / makeincluding jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia 72 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia coupler (socket) 73 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia plain tee 74 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia bend 45° 75 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia bend 87.5° 76 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia vent cowel 77 providing and fixing rigid pvc pipe fittings (is : 4985 mark) of approved quality / make including jointing the pipe with solvent cement rubber ring and lubricant. 110 mm dia pipe clip 78 construction of chamber in all types of soil with 300 mm thick masnory in cm. 1 : 6, 100 mm thick c.c. 1 : 5 : 10 in foundation , 20 mm thick inside plaster in cm 1 : 6, finished with floating neat cement 50 mm thick m 15 grade c.c. flooring earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. inside size 450 x 450 mm depth upto 0.5 m cement coverwith frame 79 construction of chamber in all types of soil with 300 mm thick masnory in cm. 1 : 6, 100 mm thick c.c. 1 : 5 : 10 in foundation , 20 mm thick inside plaster in cm 1 : 6, finished with floating neat cement 50 mm thick m 15 grade c.c. flooring earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. inside size 600 x 450 mm upto depth of 0.5 m cement cover with frame 80 construction of soakage well in all types of soil 300mm thick dry stone masonry, top and bottom 300 mm course in cm 1 : 6, 80 mm thick stone slab, jointing of slab in cm 1 : 3, ralthal, kharanja, 40 mm thick m 15 grade c.c. flooring earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr. size 240 cm dia outside & 240 cm depth 81 construction of septic tank in all types of soil with 40 cm. thick masonry in cm 1 : 6, 15 cm. thickc.c. bed of 1 : 5 : 10, m 15 grade c.c. flooring & over stone slab covering, 80 mm thick slab, jointing of slab in cm 1 : 3 ralthal, kharanja, 50 mm thick stone partition walls, 20 mm thick plaster in cm 1: 6 finished with neat floating cement, 4 nos c.i. foot rests of approved design, two no. 450 mm dia 25kg. of each c.i. cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr. size 200 x 100 x 130 cm (for 10 users) 82 construction of cement concrete chamber 125mm dia on depressed floor upto 45cm height from floor with : stainless steel sheet grating 83 wiring of light point/ fan point/ exhaust fan point/ call bell point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p iii ) vergin material pvc conduit & its all accessories( j.b. , bends etc.) , round tiles,18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, modular face plate with grid plate, 3 pin ceiling rose / lamp holder/ 3 pin connector , screws etc, making connections,all as per pre approved by engineer in charge, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheets & electrical/ wiring accessories refer chapter e 04, e 05 & e 07 . for additional technical parameters of products/ work , refer annexure a attached with this bsr short point (up to 3 mtr.) 84 medium point (up to 6 mtr.) 85 long point(up to 10 mtr..) 86 wiring of 3/5 pin 6 amp. light plug point as per pwd specification for electrical works with isi marked 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper conductor 1.1 kv grade (is:694) and 1.5 sq. mm nominal size fr pvc insulated unsheathed flexible copper earth conductor 1.1 kv grade (is:694) in recessed isi marked mms ( is:9537 p iii ) vergin material pvc conduit & its all accessories( j.b. , bends etc.) , round tiles, 18 swg hot dipped galvanized modular box with earth terminal, 6 a modular switch, 3/ 5 pin 6 a modular socket, modular face plate with grid plate, screws etc,all as per pre approved by engineer in charge, making connections, testing etc. complete as required. for specification of copper conductor, phenolic laminated sheets & electrical/ wiring accessories refer chapter e 04, e 05 & e 07. for additional technical parameters of products/ work refer annexure a attached with this bsr on board 87 medium point (up to 6 mtr.) 88 s&f following sizes (dia.) of isi marked mms ( is:9537 p iii ) vergin material pvc conduit as per pwd specification for electrical works along with its accessories (is: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required. all relative and latest acceptance tests reports by any nabl accredited lab for the conduit shall be submitted before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 20 mm 89 25 mm 90 supplying and drawing fr pvc insulated & unsheathed flexible copper conductor as per pwd specification for electrical works with isi marked (is:694) and as per is 8130 : 2013 of 1.1 kv grade . wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4, , in existing surface or recessed pvc/ ms conduit/casing capping including all as per pre approved by engineer in charge,making connections, etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. for additional technical parameters of products/ work , refer annexure a attached with this bsr 2 x 2.5 sq. mm. + 1x1.5sqmm 91 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 92 supplying and fixing of power plug point with modularaccessories as per pwd specification for electrical works, on hot dipped galvanized modular box of 18 swg with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of isi marked modular 16 amp. switch (is :3854) and 3/5 pin 16 amp. socket outlet (is:1293) [ as per detailed in respective item in bsr] , making connection , testing , etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 93 providing & fixing of modular type step fan regulator duly isi marked (is :11037) as per pwd specification for electrical works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with ip 20 rating , minimum width of 1 module switch toggle( push part ) should not less then 20mm, including all as per pre approved by engineer in charge,making connections, testing etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 5 step fan regulator 100 watt 2 module 94 providing & fixing of heavy duty capacitor start, copper woind double ball bearing 900/1400 rpm single phase exhaust fan as per pwd specification for electrical works, conforming to is:2312 isi marked in existing opening including making connections testing etc. as required. oem shall be an iso certified company. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached withthis bsr .300 mm sweep(900/1400 rpm) 95 providing & fixing of ik07 ip 66 protected led street light luminaire on existing bracket/pole. fixture made of powder coated single piece pressure die cast aluminum lm6/ adc12 material with heat dissipation fins on housing with uv stabilized pc/toughened glass cover (uv stablzation report submitted for uv cover ) and secondary lens on each led & should be smd type . the system level luminaire efficacy >=120 lm/ wt with high power leds is to be used and potted driver must be potted & has a unique bis r number with input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety ,input frequency 50hz±3% power factor >0.95 driver efficiency >85% ,thd(i) <10% humidity 10% to 90% rh working temp 5c to 45c . driver current <1000ma shown in lm79 report. the luminaire shall be bis certified and t.c. certified. life expectancy equal or more than 50000 burning hrs with minimum 70% lumenmaintened,colorrendering index>70 andcct 5700k+355k. surge protection shall be min = 4 kv internal and min 10 kv external. driver should be phase to phase protection of 440 v for 4 hrs. manufactures word mark/name engraved/embossing on die cast housing to allow traceability/authenticity. fixture shall be as per is 10322 complianced.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate/ report with liable warranty of product/accessories from oem shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr led street light fixture 70 watt 96 providing & fixing of 240/415 v ac mcb with positiveisolation of breaking capacity not less than 10 ka (b/ c tripping characteristic as per type of load and site requirement) 4kv impulse withstand voltage, as per pwd specification for electrical works with isi marked is 8828(1996) / conforming to iec 60898 1 2002, iec 60947 2, low watt losses, trip free mechanisum , energy limiting of class 3 as per iec, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , ip 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 a rating and 10,000 upto 63 a, 5000 for 80 a rating including making connections, testing etc. as required. . oem shall have submit nabl / cpri / erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with thisbsr .single pole mcb6 a to 32 a rating 97 double pole mcb50 63 a rating 98 providing & fixing of ik09 recessed/surface mountingheavy duty horizontal type sheet steel of 1.6 mm thick distribution board as per pwd specification for electrical works isi marked conforming to is 13032 & is 8623 / conforming to iec 61439 3. phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal db terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.oem shall have submit nabl / cpri/ erda accrediated lab test reports before execution & all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr ip 43 double door (single phase)6 way (6 o/g +2 i/c ) 99 supply & laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with gi/cu thimble etc. as required. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 8 swg copper wire 100 providing & fixing of ip40 led recessed / surface mounted, round / sqaure non dimmable back lit smd mid power led downlight with die cast aluminum housing & heat sink for heat dissipation with uv stabilized non yellowish diffuser with internal/ external bis complience 2.5 kv surge protected isolated driver, with short & open circuit protection, having efficiency > 85% and in compliance to iec standards. system lumen efficacy of = 120 lm / watt, thd < 10 % ,p.f.=0.95, cri >80, life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) ,maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsrrecessed mountingled downlight 18/20w 101 providing & fixing of ip40 led surface/ recessed / suspended mounting mid power smd type led light fixture made from crca sheet steel housing, high purity / transmisivity uv stabilized non yellowish diffuser for uniform light distribution. high efficiency with 2.5 kv internal/external surge protection bis certified isolated driver having efficiency > 85% , with short & open circuit protection and in compliance to iec standards (integral with light fixture). system lumen efficacy of = 120 lm/watt ,thd < 10 % , p.f.=0.95,cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends , cct 3000°k / 4000°k / 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsrrecessed mounting36w led light fixture 2x2 with acrylic / prismatic front cover 102 providing & fixing of ip20 smd mid power led batten type integrated light fixture made from polycarbonate /extruded aluminium powder coated housing with in built driver , power consumption of 18w/20w ,system lumen efficacy = 120 lm/watt output, internal surge protection of 2.5 kv with short & open circuit protection ,thd < 10% ,p.f.=0.95, cri >80 , life time of minimum 50000 burning hours with , 70% of intial lumen maintaned till life ends, cct 3000°k / 4000°k/ 5700°k /6000°k/6500°k (as per ansi bin) , maximum power consumption should not more than the specified rating and fixture shall be of bis standard and trade mark certificate ( t.c.). manufactures word mark/ name engraved/ embossing/ screen printing on housing.oem must have its own in house nabl lab setup for all testing facilities for led fixtures. (lm79/lm80) certificate / report from oem shall be submitted. all as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer annexure a attacheded with this bsr.4 led tube shape fixture 18/20 w (polycarbonate base) 103 sitc of chemical gel earthing system of dual pipe technology made of with b class g i pipe as per is 1239 ( part 1):2004 of medium duty of following sizes as per points mentioned (a), (b), [c), (d), (e) below : (a) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, cpri/ erda tested with rms capacity of minimum 35 40 ka for withstanding 1 second(b) to ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. the compound shall be tested form nabl acredeated lab for low resistivity ( less than 0.12 ohm meter) & high conductivity in nature with carbon as a major content as per referance of is 3043 1987,ieee 80 2013 (clause 14.5d) , ieee 837 & ier 1956 with latest amendemnts©heavy duty weather proof poly propylene earth pit chamber with lockable jam free lid suitable for safe working load 5000 kg or more of size top dia. 225 to 260 mm, bottom dia 300 to 350 mm. and height 250 to 300 mm.(d) testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book.(e) self certificate for confirming above standards from oem is mandatory. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr .with pipe in pipe technology (outer pipe dia. / inner pipe dia. ) minimum 100 mm dia borewellgi pipe 2000 mm long, 80 / 50 mm, terminal 50mm x 6 mm gi strip 104 providing & laying p.v.c. / xlpe insulated & p.v.c. sheathed un armoured / armoured aluminium cable of 1.1 kv grade as per pwd specification for electrical works in existing rcc / hume / stoneware / pvc pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below: (a) material : h4 grade aluminium conductor of purity >99.6 %& as per is:1554 p i / is :7098 p i(b) conductor shall have electrolytic aluminium confirming to is 8130, is 3975 1999 for armouring of cables in armoured cable items , is 5831 for sheath, is 10810 (part 0 to 64 ) for testing procedures .(c) oem must have iso 9001 & 14001 certifications for quality assuarance & its own in house nabl lab setup for all testing facilities for cables . appropriate type test certificate / oem test report shall be submitted . all above as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr . armoured cable10.0 sq. mm2.0 core 105 providing & fixing of iso certified company made bee star rated copper wounded double ball bearing capacitor start, aluminium body & metallic blade ceiling fan as per pwd specification for electrical works, conforming to is:374 2019, & is:1885 p v 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. appropriate oem test certificate shall be submitted by contractor. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 1200 mm sweep bee 2 star rated (service value >=4.5 to < 5 ) 106 supply & fixing of abc type (map 50) type powder fire extinguisher (stored pressure type) of following capacity duly current and valid bis certification conforming to is: 15683:2006, with dry chemical powder used as extinguishing agent should be mono ammonium phosphate 50% concentration conforming to is 14609:1999. oem will produce supplier certificate complete with squeeze grip release valve, locking arrangement, pressure gauge and bracket including initial fill and wall suspension complete in all respect. serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. the firm should submit the product certificate from an en notified body & product performance test report from nabl accredited lab as per is 15683. . all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 4 kg 107 supply installationtesting&commissioningofisocertified manufacturer made monoblock motor pump set isi marked (is:9079 2002) with tefc motor, motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011. with stainless steel impellor, stainless steel shaft, mechanical seal, single/three phase ( 240 440 v ) permanent split capacitor type (psc), fitted with thermal overload protection, . including cost of hardware etc on existing platform complete. pump shall have following hp rating, phase, head, minimum discharge respectively complete in all respect. appropriate type test certificate / oem test report shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 0.5 hp, 1 ø, (3 18)mtr, (100 26) lpm 108 construction of tube well 100 metre depth and above in all type of rocks by dth system and over burden, to accommodate casing pipe of following size in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per is : 2800 (part i & ii) 1979 specifications. the work would be completed after obtaining sand free water. the tube well should have a throughout bore as per nominal dia of casing pipe. 200 mm dia nominal bore 109 development of tube well as per is specifications using suitable compressor to give sand free water for required yield of the gravel packed tube well. 110 supply of erw m.s. black casing pipe isi marked (is : 4270/1992) of grade fe 410 of following sizes at site of work. nominal bore of pipe200 (mm) 111 supply & fixing tube well cover of m.s. sheet (6 mm thick) with nuts and bolts complete for casing size. 200 mm dia 112 supply & fixing m.s. clamp, set of 50 x 6 mm flat from iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. 113 providing & fixing of single stage, water cooled, high speed(2880 rpm), horizontal, centrifugal, openwell submersible pumps set pre filled with coolent water and fitted with mechanical seal t/c vs t/c, thrust bearing shall be of carbon + s.s.the stator body of single phase pump shall be of ss and rest of all shall be of cast iron. all casting parts should be cathod electro deposition (ced) coated and other construction material should be confirming to is : 14220: 2018 . the overall performance of pump shall confirm to bee energy efficiency level of 3 star. valid bee certificate from oem must be submitted for the same. motor should be ie2 class as per iec 60034 2 1: 2007, iec 60034 30: 2008, & is12615:2011, including making connection etc as required complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 2.0 hp, 1 ø, (12 25) mtr, (350 115) lpm 114 supplying andlaying isimarkedp.v.c. insulated submersible cable as per pwd specification for electrical works confirming to is:694 and as per is 8130 : 2013 of 1.1 kv grade .wire should be made from 99.99% purity copper, class 5 stranding in acc. to iec 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation pvc type a ,flame retardant as per is 10810 53, better amperage rating as per vde 0298 part 4 including making connection etc. as required. oem must have its own in house nabl lab setup for all testing facilities for wires. all as per pre approved by engineer in charge, making connections. for additional technical parameters of products/ work , refer annexure a attached with this bsr 6.0 sq.mm 3 core flat / round 115 providing & fixing of hdpe pipe isi mark (is:4984/2016 ) for watersupply (suitable for submersible & jet pump) with required fittings ie socket, elbows, tee etc. complete in all respect. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr 50 mm od 6 kg / cm2 116 construction of 185 cm. dia platform as per approved design and drawing of unicef. 117 supply installation testing & commissioning of iso certified company made dol/star delta starter panel made out from 1.6 mm thick powder coated crca sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, illuminated on / off push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. appropriate type test certificate / oem test report shall be submitted. all as per pre approved by engineer in charge. for additional technical parameters of products/ work , refer annexure a attached with this bsr for single phase submersible / monoblockpump0.5 hp to 3.0 hp (dol starter) ...

Directorate Of Purchase And Stores - Rajasthan

33952578 supply and safe delivery of spare thrust bearing assembly, bearing bushes, sleeves, shaft coupling etc for m / s. wilo mather and platt make supply and safe delivery of spare thrust bearing assembly, bearing bushes, sleeves, shaft coupling etc for m / s. wilo mather and platt make , spares of spare thrust bearing assembly impeller nose cad , o seal ring , impeller taper distance sleeve , pump bearing brush , coupling moc , intermediate bearing bush , intermediate bearing sleeve , tilting pad type thrust...

North Western Railway - Rajasthan

33628224 supply of thrust bearing no. 51109 hthrust bearing no. 51109 h, thrust bearing no. 51109 h for sab regulators make nbc, skf, nachi, rbc, excel offer accepted make: nbc...

Rajasthan State Road Transport Corporation - Rajasthan

33555482 rsrtc invites the tender for ball and tapper roller bearings tata leyland and eicher rsrtc invites the tender for ball and tapper roller bearings tata leyland and eicher , specifications of ball & tapper roller bearings as:190:81:march:2014, as:322:66:jan:2004 , 2691 2620 0143 /3125/3133 bb455236 fsassy. needle cage bearing , 2691 2620 0142 /3124/3130 bb728040fsassy needle cage bearing , 2691 2620 3120 / 3123 / 3132 bb 808840fs needle bearing , 2691 2630 3104 tapper roller bearing25572 25520, bs iii/2017 , p4900402/ mub 7307/ jc 8035 tail pinion bearing bs ii , f0243210/f0255010needle roller bearing , f0242510/ f0254010 spigot bearing , f0243010/ f0254610 needle roller bearing 1st , f0242710/ f0254910needle roller bearingbb44545fs , f0243110 /f0254710 needle rollerbearing 1st bb627040 , f0242410/ f0259310 roller bearing (nup 309em) , f0248510/ f0254510taper rollerbearing (2789 2729) , p4900202 diff. pinion bearing (493 497) , f0259210/ jc 8020cyl. roller bearing ips , f0246010 tapper bearing (567 563) , 55200/55437tapper bearing zf , mb563234 ps center bearing eicher (tx 7240) , f 0238910 /6305 lu fly wheel bearing tc , ib001825 needle bearing 3rd(b60049) , ib001824 needle bearing 1st (b60047) , ib001826 needle bearing reverse (b60048) , ib003070pilot bearing m/s eicher midi , if000148/bb60063needle bearing 4th eicher midi , if000864 / nup307 mnrneedle bearing c/s , if000863 / nup307 mnneedle bearing c/s , id200359 /jc 8022bearing , id200480 / bb60107needle roller bearing 1st , id200456 / bb60109needle roller bearing 2nd , id200349 / b60106needle roller bearing reverse , 2691 2625 3105cylinder rollerbearing ar7.5 75 100, bs iii/2017/2013 , 2691 2620 3103/ tapper roller bearing 28580/521 bs iii/2017/2013 , 2691 2620 3106needle cage bearing tata , 2516 2635 3104roller ring (rev idler gear ) , id200457bearing 3rd speed , id200458bearing 4th speed , id200453bearing drive pinion , 2691 2625 3113bs iii/2017roller thrust bearing arrgmt , f0267310bearing 6.s.850 , f0267510bearing 6.s.850 , f0267410n.r. bearing , f0256310 nr bearing 5th6.s. 850 , f0267710input shaft bearing , 206035013001tapper rollerbearing 31312l bs iii/2017 , 2573 3530 3101/ 47487/20diff.cage bearing , 2691 2620 3111needle cage bearing ist , jc 409025pinion bearing lay , pop00150pilot bearing r160 crb , hk4012 ntnbearing leyland , 0009811201/nu309ncyl. roller bearing , 2505 2620 3106four point ball bearing qj309 , 2505 2620 3123double row needle cage bearing , 2505 2620 3124double row roller cage bearing , 2505 2630 3104t.r. bearing bs1/2/3/4 , 6202bearing , 6204bearing , db142012pn.r. bearing...

Rajasthan Rajya Vidhyut Utpadan Nigam Limited - Rajasthan

33263446 purchase of critical type bearings category b against nit no. tn 09 / 2022 23 purchase of critical type bearing category b against nit no. tn 09 / 2022 23 , chhabra thermal power project, rvun, chhabra , 6004.2z.c3 , bearing 6006 , 6007 2rs , 6009 2rsr , bearing 6012 , 6012rsrc3c140 , bearing 6016 , bearing 6018 , bearing 6019 , bearing 6020 , bearing 6021 , bearing 6024 , bearing 6028 , bearing 6008 , bearing 6012 a , bearing 6201 , bearing 6202 , bearing 6202 2rs , bearing 6202 2z , bearing 6202.2z.c3 , bearing 6203 , bearing 6204 , bearing 6204 2z , bearing 6205 , bearing 6206 , bearing 6206 2rs , bearing 6206 zz , bearing 6207 , bearing 6208 zz , bearing 6208 , bearing 6208.2z.c3 , bearing 6208.2rs1 , bearing 6208.2rs.c3 , bearing 6209.2z.c3 , bearing 6209 , bearing 6209 zz , bearing 6210zz , bearing 6210 , bearing 6211 , bearing 6211.c3 , bearing 6212 , bearing 6212.c3 , bearing 6212 2z.c3 , bearing 6213 , bearing 6213.c3 , bearing 6215 zz , bearing 6216 , bearing 6216 2rs1 , bearing 6217 , bearing 6218 , bearing 6219 , bearing 6232 , km 17 , mb 26 , km 26 , mb 17 , uc209 , uc204 , csa212 , csa211 , bearing 6301 , bearing 6304 zz , bearing 6305 2z , bearing 6305 2z.c3 , bearing 6306 2z.c3 , bearing 6306 zz , bearing6306 2rs1 , bearing 6306 , bearing 6307 , bearing 6308 , bearing 6308 zz , bearing 6308.2z.c3 , bearing 6308.2rs.c3 , bearing 6309.2rs1 , bearing 6309 , bearing 6309 2z , bearing 6310 , bearing 6310 +h305 , bearing 6310 zz c3 , bearing 6311 c3 , bearing 6312 , bearing 6312.c3 , bearing 6313.c3 , bearing 6313 zr , bearing 6319 , bearing 6319.c3 , bearing 6321.c3 , bearing 6404 , bearing 6405 , bearing 6406 , bearing 22220cc / w33 , bearing 22222cc / w33 , bearing 22222 cck / w33 + h 322 , bearing 22222e1k , bearing 22224e1k , bearing 22226e1k , bearing 22226 e , bearing 22226 cck / w33 + h3126 , bearing 22228 cck / w33+h3128 , bearing 22230e1k , bearing 22230cc / w33 , bearing 22232e1k , bearing 22232 cck / w33 + h3132 , bearing 22244e1k , bearing 22244 cck / w33 with sleeve 3144 , bearing 22211 ek / ck + sleeve h 311 , bearing 22215 ek / ck + sleeve h 315 , bearing 22216ek / ck + sleeve h 316 , bearing 22216 cc / w33 , bearing 22216 , bearing 22217 , bearing 22217 cc / w33 , bearing 22217 ek / ck + sleeve h 317 , bearing 22218 ek / ck +sleeve h 318 , bearing 22219 cc / w33 , bearing 22220 ek / ck + sleeve h 320 , bearing 22222 e , bearing 22222 ek / ck + sleeve h 322 , bearing 22226e1amc3e1c3 , bearing 22309e , bearing 22308 , bearing 22311 , bearing 22311e1c3 , bearing 22313e1am , bearing 22314 , bearing 22314e1amc3 , bearing 22316 ek / ck + sleeve h 2316 , bearing 22319 , bearing 22320 , bearing 22322 , bearing 22312e1am , bearing 23136e1akm , bearing 23148 e1k + aoh3148 , bearing 2312 k + sleeve h 2312a , bearing23218 cck / w33 + sleeve h 2318 , bearing 23222 cck / w33 + sleeve h 2322 , bearing 23120 , bearing 23024 , bearing 23030 , bearing 23028 , bearing 23028 e1akm / w33+h3028 , bearing 23226cc / w33 , bearing 23064 e1a.mb1 ( brass cage ) , bearing 23236cc / w33 , bearing 23248cc / w33 , bearing 22330 e1 , bearing 23268cak / w33 + sleeve h3268 / 8151 + lock washer with locking clip , bearing 24030 smb , bearing 24064 e1a.mb1 ( brass cage ) , bearing 23128e1km , ahx3128 , bearing 30312a , bearing 30214a , ncf2926vc3 , ncf2928vc3 , ncf 2928 r / c3 , ncf2936 vc3 , ncf2938 vc3 , ncf3032 vc3 , ncf2948 vc3 , nj2306ecp / c3 , nj2318emiac4 , nj210e , nj2322emic3 , nj2308ecp / c3 , nj2310ecp , nj306 ecp / c3 , nj204 ecp , nj310 ejp / c3 , nu221.c3 , nu228em1 , nu236e.m1 , nu308 , nu313 , nu319 ecp , nu310e , bearing 2922 , sl182928bxl.c3 , sl 182932 bxl.c3 , ge 35 es 2rs , ge340 dw 2rs2 , ge 80es xxog , e 32226j , wu 150x270 m1.c4 ( fag / schaeffler make specifications ) , bearing 3310 a / c3 , bearing 3309 atn9 / c3 , bearing 3206 a / c3 , bearing 3205 a / c3 , bearing 3215 b / atup , bearing 32324 j , dyzv7307 , 1306 etn9 , 1213ektn9 +h305 , ta 1825 z , hk 1512 , sleeve no. h313 , sleeve no. h315 , sleeve no. h317 , sleeve no. h320 , sleeve no. h322 , sleeve no. h3124 , sleeve no. h3126 , sleeve no. h3130 , sleeve no. h3132 , sleeve no. h 3136 , sleeve h309 , bearing 29344 e , bearing 29322e , bearing 29332 e , bearing 211 ec , bearing 6220 , bearing 792 795 , bearing 48220 48290 , bearing 98350 98788 , mh813844 mh813810 , bearing 9285 9220 , bearing 749a 742d , bearing 32216 j2 / q , bearing 2312 , bearing 1211 ektn 9 , bearing 3203 atn 9 , t 210j , bearing 7309 , bearing ck 72212 / 2 &sk72487 / 3 , bearing 7214 bep , bearing 7314 , 310ec , bearing 30220 j2 / df , bearing 30210 j2 / q , bearing 30220 , bearing 30226 , bearing 30213 , bearing 30217 , bearing 30219 , bearing 31308 , bearing 30310 , bearing 31311 , bearing 31314 , bearing 31313 , bearing 31315 , bearing 31317 , bearing 31319 , bearing 3220 a / c3 , bearing 32006 , bearing 32014 , bearing 32213 , bearing 32216 , bearing 32218 , bearing 32219 , bearing 32232a , bearing 32302 , bearing 32305 , bearing 32306 , bearing 32307 , bearing 32308 , bearing 32310 , bearing 32309 , bearing 32311 , bearing 32311 j2 , bearing 32312 , bearing 32312a , bearing 32312 c3 , bearing 32314 , bearing 32313 , bearing 32315 , bearing 32315 / q , bearing 32316 , bearing 32318 , bearing 3306 , bearing 3307 , bearing 33205 , bearing 33207 , bearing 33207 c3 , bearing 33208 , bearing 33209 c3 , bearing 33209 , bearing 33213 , bearing uk216+sleeve h 2316 , bearing 23022 , ncf2948vc3 , bearing 23060 e1 ( brass cage ) , bearing 22248 e1 , bearing 22232 e1am ( brass cage ) , total , chhabra supercriticalthermal power project, rvun, chhabra , bearing 6204 zz , bearing 6205 zz , bearing 6205 2zc3 , bearing 6206 2zc3 , bearing 6206 zz , bearing 6207 zz , bearing 6208 zz , bearing 6209 zz , bearing 6210 zz , bearing 6309 zz , bearing 6310 zz , bearing 6313 zz , bearing 6313 c3 , bearing 6314 c3 , bearing 6316 c3 , bearing 6318 c3 , bearing 6319 c3 , bearing 6322 c3 , bearing nu 234 c3 , bearing nu 319 c3 , bearing nu 322 c3 , bearing nu 324 c3 , bearing 32313 , bearing 22318 , bearing 32030 , bearing 32315 , bearing 32219 , bearing 22326 , bearing 32034 , bearing 2211k+sleeve h311 , bearing 2216k+sleeve h316 , bearing 22218k+sleeve h318 , bearing 22220k+sleeve h320 , bearing 22222k+sleeve h322 , bearing 22240cckc3 / w33 +sleeve h3140 , bearing 23024 cck / w33 +sleeve h3024 , bearing 23026 cck / w33 +sleeve h3026 , bearing 23028 cck / w33 +sleeve h3028 , bearing 23030 cck / w33 +sleeve h3030 , bearing 23032 cck / w33 +sleeve h3032 , bearing 23034 cck / w33 +sleeve h3034 , bearing 23036 cck / w33 +sleeve h3036 , bearing 23040 cck / w33 +sleeve h3040 , bearing 23044 cck / w33 +sleeve h3044h , bearing 23048 cck / w33 +sleeve h3048h , bearing 24030 e#1 , bearing 23044 e#1 , bearing 230381 e1 a#m , bearing 2216 bearing+sleeve , bearing 22218 bearing+sleeve , bearing 6307 zz , bearing 6305 zz , bearing 32928 / q , bearing 24030 e1 k295 080804 0200 , bearing 6205 pt , j0913 , bearing 22211 k / c3 + sleeve h311 , plummer block ( snv 100 f l ) with double lip seal , bearing 6308 zz , bearing 6202 zzc3 , bearing 6208 z , bearing 3313 , bearing 6005 2rsr , bearing 6304 , bearing 6310 z , bearing 6312 , bearing uc 209 , bearing ucf 209 , bearing uc 204 , bearing ucf 204 , bearing 6212 zr , bearing 6211 , bearing 6311 2rs , bearing 7306 b , bearing 32310 a , bearing 32311 a , bearing 32024 x , bearing 22209e1ak.m + sleeve h034 , bearing ( de ) ball bearing skf 6220 , bearing ( nde ) ball bearing skf 7220 becbm , bearing 6205 zz c3 , bearing 6202 zz , bearing 6307 lb , bearing 6311 zz , bearing 6311 zz c3 , bearing 6312 z c3 , bearing 6315 zz , bearing 6317 c3 , bearing 6318 2rs , bearing nu 322 , bearing 6212 , bearing 6206 2rs c3 , bearing 6206 2hrs c3 , bearing 6208 z c3 , bearing 6212 c3 , bearing 6322m / c3vl0241 , bearing nu 224 c3 , bearing 7320 b , bearing 6224 c3 , bearing nu 226 c3 , bearing 6226 c3 , bearing nu 230 m , bearing nu 219 ec mc3 , bearing 6320 mc3 , bearing nu 236 m , bearing 7220 b , bearing nu 220 c3 , bearing 6220 c3 , bearing 6236 c3 , bearing 22315 sk mbc3 , bearing 22308 e1 x2 c3 , bearing 22310 exq w33 , bearing 29324 e1 , bearing 3309 a , bearing 6317 , bearing 7316 be , bearing 29322 e , bearing 6409 c3 , bearing 6313 z c3 , bearing 3314 c3 , bearing 6315 , bearing 6306 c3 , bearing 7319 becbm , bearing 16026 , bearing 6310 c3 , skf 938 / 932 , timken 932 m8 dp , bearing 32222 , bearing 22317 sk mb , sleeve h 2317 , bearing 6309 c3 , bearing 6313z , bearing 6210 , bearing 6309 , bearing 6408 z , bearing 6211 c3 , 7214 becbj , bearing 7313 , bearingfor 43.5 m dia x 3.5 mswd + 0.425fb , bearing 6312 c3 , bearing 6309 z c3 , bearing nu 305 ecp , bearing 3306 , bearing 6307 , bearing 7206 becbp , bearing 7214 becbm , bearing 29320 , bearing 29324 e , bearing 3310 , bearing 22211 , bearing 22309 c3 , nj314 , bearing 3610 zz , bearing 22328ccja / w33 , 4910v , suratgarh supercriticalthermal power project, rvun, suratgarh , nj412 cylindrical roller bearing , nj2319 ecp c3 cylindericalroller bearing , nu218 cylindical roller brearing. , nu 219m cylinderical roller brearing , nu220 cylindericalroller bearing. , nu 224 c3cylindericalroller bearing , nu 226 m cylindericalroller bearing , nu226m + 6226c cylinderical roller bearing , nu230 m cylindericalroller bearing , nu313 cylindericalroller bearing , nu316c3 cylindericalroller bearing , nu413 cylindericalroller bearing , nu1028mcylindrical roller bearing , nu1030m+6030c3 cylindrical roller bearing , nup 2213 cylindrical roller bearings , 1305 self aligning ball brg. , 1503 self aligning ball brg. , 1603 self aligning ball brg. , 3206 double row angular contactbrg. , 3206 bd c3 angular contract ball bearing , 3311double row angular contactbrg.. , 6016 deep groove ball bearings , 6036 deep groove ball bearings , 6202 zz c3 deep groove ball bearing , 6203 deepgroove ball bearing , 6204 deep groove ball bearing , 6204 zz c3 deep groove ball bearing , 6204 c3 deep groove ball bearing , 6205 deepgroove ball bearing , 6206 deep groove ball bearing , 6206 2rs1 single row deep groove ball bearing , 6208 2rs1 deep groove ball bearing , 6208 z deep groove ball bearings , 6208 zz deep groove ball bearing , 6208 zz c3 deep groove ball bearing , 6209 c3 deep groove ball bearing , 6209 zzc3 deep groove ball bearing , 6211deep groov ball brg. , 6212 c3 deep groove ball bearing , 6212 z deep groove ball bearing , 6212 zz deep groove ball bearing , 6213 c3 deep groove ball bearing , 6213 zz deep groove ball bearing , 6215 c3 deep groove ball bearing , 6215zz deep groove ball bearing , 6217deep groov ball brg. , 6218deep groovball bearing , 6218 c3 deep groovball bearing , 6220deep groovball bearing , 6220 c3deep groovball bearing , 6224 c3 deep groove ball bearing , 6228 c3 deep groove ball bearing , 6230c3deep groovball bearing , 6304 zzdeep groov ball brg. , 6305 deep groov ball brg. , 6308deep groov ball brg. , 6308 zzdeep groov ball brg. , 6309deep groov ball brg. , 6312 c3 deep groovball bearing , 6313 c3deep groovball bearing , 6313 zzdeep groovball bearing , 6314 c3 deep groove ball bearing , 6314 c4 deep groove ball bearing , 6314znr c3deep groov ball brg. , 6315 c3deep groovball bearing , 6315 2z c3deep groovball bearing , 6316 c3deep groovball bearing , 6317 c3deep groovball bearing , 6319 c3deep groovball bearing , 6319 2z c3deep groovball bearing , 6322 c3deep groovball bearing , 6406deep groov ball brg. , 6410 open deep groove ball bearing , 6412 deep groove ball bearing , 7213angular contact ball brg. , 7214 bgangular contact ball bearing , 7315single row angular contact ball brg. , 7316 angular contact ball brg. , 7319 angular contact ball bearing , 7320angular contact ball bearing , 16026 deep groov ball brg. , 22210k + h310 spherical roller bearing , 22213k+ h313 spherical roller bearing , 22218k+ h318 spherical roller bearing , 22219 ckspherical roller bearing , 22220k+ h320 spherical roller bearing , 22222 spherical roller bearing , 22222k+ h322 spherical roller bearing , 22224cspherical roller bearing , 22224k+ h3124 spherical roller bearing , 22226 spherical roller bearing , 22226k+ h3126 spherical roller bearing , 22228k+ h3128 spherical roller bearing , 22230 spherical roller bearing , 22230k+ h3130 spherical roller bearing , 22232 spherical roller bearing , 22232k+ h3132 spherical roller bearing , 22320 ck spherical roller bearing , 22326 spherical roller bearing , 23024k + h3024 spherical roller bearing , 23028k + h3028 spherical roller bearing , 23032k + h3032 spherical roller bearing , 23036k + h3036 spherical roller bearing , 23040k + h3040 spherical roller bearing , 23044 spherical roller bearing , 23064k + h3064hg spherical roller bearing , 23134k+ h3134 spherical roller bearing , 23136k+ h3136 spherical roller bearing , 23138k+ h3138 spherical roller bearing , 23140k+ h3140 spherical roller bearing , 23144k+ h3144a spherical roller bearing , 23148k+ h3148a spherical roller bearing , 23152k+ h3152a spherical roller bearing , 24168e1k30 + h3168a spherical roller bearing , 24030 e1 spherical roller bearing , 29240 spherical roller thrust bearings , 29320espherical roller thrust bearing , 29322e spherical rollar thrust bearing , 29422e spherical rollar thrust bearing , 30207 taper roller bearing , 30214 taper roller bearing , 30312 taper roller bearing , 31306 taper roller bearing , 32224 a tapered roller bearing , 51228 thrust ball bearings , ucf312 ball bearing block assembly , 6218 j20aa c3 insulated deep groove ball bearing , 6220 c3 insulated deep groove ball bearing , 6224 c3 insulated deep groove ball bearing , nu1028m insulated cylindrical roller bearing , 33019 / q tapper cylindrical bearing , 6306 2z l207 c3 single row deep groove ball bearing , total , suratgarh thermal power station, rvun, suratgarh , 6305deep groove ball bearing , 6214 c3 deep groove ball bearings , 6217 c3 deep groove ball bearings , 6306 c3 deep groove ball bearing , 6316 c3 deep groove ball bearing , 6317 c3deep groove ball bearings , 6318 c3deep groove ball bearings , 6014deep groove ball bearing , 6016 deep groove ball bearing , 6018deep groove ball bearing , 6021deep groove ball bearing , 6024 deep groove ball bearing , 6026 deep groove ball bearing , 6028 deep groove ball bearing , 6208 2z / 2zr deep groove ball bearing , 6210 c3 deep groove ball bearing , 6212 z deep groove ball bearing , 6224 deep groove ball bearing , 6305 2z deep groove ball bearing , 6306 zzdeep groove ball bearings , 6307 c3 deep groove ball bearing , 6309 c3 deep groove ball bearing , 6321 c3 deep groove ball bearing , 6020 z deep groove ball bearings , 6206deep groove ball bearings , 6213 2z c3deep groove ball bearing , 6220 c3deep groove ball bearing , 6234 m c3deep groove ball bearing , 6308 2z deep groove ball bearing , 6308 2z c3 deep groove ball bearings , 6309 zz c3 deep groove ball bearings , 6312 c3 deep groove ball bearings , 6312 2z c3deep groove ball bearing , 6314 deep groove ball bearing , 6315 c3 deep groove ball bearings , 6316 c3 deep groove ball bearing , 6319 c3 deep groove ball bearing , 6315 deep groove ball bearing , 6205 c3 deep groove ball bearing , 6210 zz deep groove ball bearing , 6309 deep groove ball brg , 6313 c3 deep groove ball bearing , 6313 2zrc3 deep groove ball bearing , 6218 deep groove ball bearings , 6311deep groove ball bearing , 6210 c4 deep groove ball bearing , 1213 k deep groove ball bearing , 1306 tvself aligning ball bearing , 7313 b jb angular contact ball bearing , 3307 a angular contact ball bearing , 7213 bjp angular contact ball bearing , 3207 btnh angular contact ball bearing , 3213 btvh angular contact ball bearing , nu 226 em1c3cylindrical roller bearing , nu 319 emi c3 cylindrical roller bearing , nu 321 emi c3 cylindrical roller bearing , nu 322 em1c3cylindrical roller bearing , nu324 emic3 cylindricalroller bearing , n 321 em1 c3cylindrical roller bearing , nu 220 em1c3 cylindrical roller bearing , nu 1020 ml cylindrical roller bearing , nu 2226 ecp / c3 cylindrical roller bearing , nu 318 ecj / c3cylindrical roller bearing , nu 307 cylindrical roller bearing , nu 218 etvp2cylindrical roller bearing , nu 2211 e m1 cylindrical roller bearing single row , nu 211 e m1 cylindrical roller bearing single row , nu 317 ecm c3 cylindrical roller bearing , 22217 ek spherical roller bearing , 22222 ek / c3 spherical roller bearing , 22226 cck / w33 spherical roller bearing , bearing 23236cc / w33 , 22217 cck / eiakm spherical roller bearing , 22220 e1 akm spherical roller bearing , 22224 cck / eiakm spherical roller bearing , 22317 ek spherical roller bearing , 22322 e1am spherical roller bearing , 22316 e1am spherical roller bearing , 23120e1 am c3 spherical roller bearing , 22226ek / c3 + h3126 spherical roller bearing , 23138 e1 akm spherical roller bearing , 48290 / 48220tapper roller bearing , 22234 cck / eiakm , 23144 cck / eiakm spherical roller bearing , 22211 e1akm+h311 or 22211kejw33+h311 spherical roller bearing , 22213 cck / e1 akm spherical roller bearing , 22228 cck / e1 akm spherical roller bearing , 22311 e1 c3 spherical roller bearing , 23136 e1 akm spherical roller bearing , 23228 e1 akm+h 2328 or 23228kemw33+h2328 spherical roller bearing , 23128 cck / w33 + ahx 3128 , 23064 cc / w33 spherical roller bearing , 24064 cc / w33 spherical roller bearing , h 311 sleevespherical roller bearing , h 313 spherical roller bearing sleeve , h 317 spherical roller bearing adopter sleeve , h 3124 spherical roller bearing sleeve , h 3126 spherical roller bearing sleeve , h 3128 spherical roller bearing sleeve , h 3132 spherical roller bearing sleeve , h 3134 spherical roller bearing sleeve , h 3136 spherical roller bearing sleeve , h 2317 spherical roller bearing sleeve , h 3144 spherical roller bearing sleeve , h 2328 spherical roller bearing sleeve , spherical rollerbearing 23248 ccw33 , 23268 cak / w33+sleeve oh 3268h+ lock nut hm 3168 , 22217 e1k spherical roller bearing , 22216 e1am spherical roller bearing , 22324 smb / skmb spherical roller bearing , 32318 a , 32208 tapper roller bearing , 22326tapper roller bearing , 30310 tapper roller bearing , 30312 atapered roller bearing , 31322 x tapper roller bearing , 32209 a taper roller bearing , 32312 a tapper roller bearing , 32313a taper roller bearing , 32314 a tapered roller bearing , 32317 a tapper roller bearing , 98350 / 98788tapper roller bearing , hm 813844 / 813810tapper roller bearing , 795 / 792tapper roller bearing , 9285 assy.902a5 tapper roller bearing , 32218 j2 / q taper roller bearing , taper roller bearing 749a assy.90070 , 30315 a tapered roller bearing , 32020tapper roller bearing , 32212 j2 / q tapered roller bearing , 32218a taper roller bearing , 30313 j2 / q tapper roller bearing , 30216 j2 / q taper roller bearing , 31313 j2 / q cl 7c tapper roller bearing , 29322 e1 spherical roller thrust bearing , hm926749 cup: hm926710d with spacer hm926749 xe , ucpx 12 bend pulleys of ilms of chp stg. i & ii. make: ntn , bearing qj320 n2mpac3 , ucpx 15 , h322bearing sleeve , h 3126 sleevespherical roller bearing , h3134bearing sleeve , 7309 btvpua angular contact ball bearing , 3310 bd angular contact ball bearing , nu 313 cylindrical roller bearing , 22209 e1 c3 spherical roller bearing , spherical roller bearing adaptor sleeve h 309 , spherical roller bearing22312 k , he 2312 spherical roller bearing sleeve , spherical roller bearing22308 e / c3 , 22224 e1 k or 2224kejw33 / kymw33spherical roller bearing with sleeve h3124 , 22232 e1 akm spherical roller bearing with sleeve h3132 , 22234 e1k spherical roller bearingwith sleeve h3134 , 22236 e1k spherical roller bearingwith sleeve h3136 , 22213 e1 akm spherical roller bearing with sleeve h313 , 22222 e1 akm spherical roller bearingwith sleeve h322 , 22228 e1 kor 22228kejw33 spherical roller bearing with sleeve h3128 , ge70es ( skf ) plain redial sperical brg. , 32221 j2 tapered roller bearing , ucf 213bearing block , ucf 212bearing block , sleeve 3140 , total , dholpur combined cycle power project, rvun, dholpur , bearing 71450 , bearing 6202 , 6315 c3 , 6316 c3 , total , kota super thermal power station, rvun, kota , brg. 29422 e , brg. 6030 , bearing 7313 , 29324e , bearing 6020 , brg. 22228 cck / w33 , bearing 29330 , brg. 6408 , bearing 6306 , bearing assembly ( non exp ) with brg. 1h22317 , thrust brg. 29338 e , thrust brg.29322 , spherical roller brg.22316 smbc3 , brg. 32209 a , brg. 32212 a , brg. 32218 a , brg. 3313 btvh , brg. 29426 e , brg. 22326 cc / c3w33 , brg. 29422 e1 , brg.22322 e1am , brg. nu 308 ecp , bearing 6205 , nu 2308 ec roller bearing , 22312eak , sleeve hkg h 2312 , 23220 cc / w33 / 23220 e1am , bearing no. 30311d , bearing no. 72212 / 72487q , bearing no. 32213 , bearing 22308 e / c3 , bearing no. 22317ekw33j , sleeve / adopter sleeve h 2317 , bearing no. 6307 c3 , bearing no. 6213 , bearing no. 3307 c3 , bearing no. nj 210 , bearing no. 6308 z , bearing 6217 , bearing no. 22315 smb , bearing no. 2224 e , bearing no. 22320 smb , bearing no. 29426 e1 ( nde ) , bearing no. 22326 cc / c3 w33 , 22220e / c3 , 31311 s2 / q , 6210 c3 , nu 319 em / c3 , 6208 zz , 6208 zz c3 , 6308 deep groove bearing , 6319 c3 , bearing no. 22216 e1 am , bearing no. 3313 s / 3313 b tvh ( fag ) , bearing no. 22313 smb , bearing no. nu 314 em1 , bearing no. nu 318 em1 , deep grove bearing6308 , bearing no. 3207 , bearing no. 7213 , bearing 31311a , bearing nu326 , bearing no. 3311 s , 6202 2z , 6203 zz , 6302 cm , double roller tapered worm shaft thrust bearing 29438ejw18w66 ( pair ) , cylindrical roller vertical shaft upper radial 280ru92ac1112 r3 imported , journal bearing upper tapper roller trb h 242649 / h242610 ( imported ) , journal bearing lower tapper roller trb hh437549 / hh437510 imported , vertical shaft thrust bearing trb t811 902a1 imported , vertical shaft lower radial bearing crb nu330 / ema imported , cylindrical roller worm shaft radial bearing crb 170rn03aa782r3 imported , cylindrical roller thrustbearing lower t ecrt 624 , tapper roller bearing for feeder gear box ( for worm gear ) trb 552a 2024 / 560 20024 , head pully bearing for volumetric feeder yel 209 , deep groove ball brg.6209 2rsr , deep groove ball brg.6212 2rsr , 23236 cc / w33 ( imported ) , 23248 cc / w33 ( imported ) , 23064e1am , 24064bmb , 23264kmb with sleeve , 23128 e1ak.m with withdrawal sleeve and lock nut& lock washer , uel209d1 / uel209d1 w33 , 22309e , 6212 2z , bearing 6204 , 6009 z , 6207 2z , 6306 2z , 6305zz , 30214a , 30312a , 23122 c , bearing 30220 , hr 303 mj , nu 309 w , hr 32217 j , bearing 6210 , hr 30309 j , bearing 23122 , hr 32213 j , hr 30308 j , 6306 2rs , bearing 21305 , bearing 22309 , qj313 , bearing 22313 , 6220 z , nu 220 , 63062z / c3 , bearing 22309 , qj313 , bearing 21313 , 6220 z , nu 220 , nu 210 ecj , 7214 becbm , bearing no.6020 , brg. no 29324 e , bearing no. 29322 e , bearing no.29317 e , brg no nu 313 , bearing no.7313 , bearing no.6024 , bearing no.29416 e , bearing 6310 , bearing no.31310 j2 , bearing no. nup 2310 ecp , brg. no., 32311 j2 , bearing 81216 tn , bearing nj 317 ecp / cylirdrical roller brg , bearing 6313 z nr , bearing 6313 z c3 , bearing no.6314z , bearing no.6314znr , 6004c3 , 6004zzc3 , 6205zz , 6205zzc3 , 6206c3 , 6206zzc3 , 6207zzc3 , 6208zz , bearing 6209 , 6209zz , 6209zzc3 , 6212 2rsrx2 , 6213c3 , 6216c3 , 6226c3 , 6240mc3 , 6305zz , 6306zz , 6308zz , bearing 6309 , 6309zz , 6309zzc3 , bearing 6310 , 6310zz , bearing 6312 , 6313c3 , 6313 2rs , 6314c3 , 6315c3 , 6316c3 , bearing 6317 , bearing 6318 , 6319c3 , bearing 6322 , 6322c3 , 7320becbm , 7322bg , 7324 bmpuo , nu226 em c3 , nu240em , nu316 , nu316c3 , nu318 , nu319c3 , nu320 , nu321 , nu322 , nu324 , nu326 , nu326ecmc3 , tapper roller bearing 29322e1 , 6310zzr , bearing ms11 , bearing 6406 , 23238e1c3 , bearing 6202 , bearing 6205 , bearing 51205 , bearing 6203 , bearing 6204 , bearing 30203 , bearing 30204 , bearing 30205 , radial ball bearing 30x68x15 , radial ball bearing 40x68x15 , radial ball bearing 30x62x16 , radial ball bearing 35x62x14 , radial ball bearing 30x55x13 , radial ball bearing 25x47x12 , radial ball bearing 35x62x14 , thrust ball bearing with sleeve 30 / 47x11 , thrust ball bearing with sleeve 25 / 47x15 , needle cage b30x35x17 , needle cage b20x24x13 , 22244 cck / c3 / w33 , bearing 32222 , 30228 j2 , 22240 cck / c3 / w33 , 22238 cck / c3 / w33 , 22236 cck / w33 , 22228 c3 / c33 , ncv 2936 / sl 182936 / ncf2936v , 23226 e1am / cc / w33 , 22218 ck , nj2318 em1c3 , 22236 cck / c3 / w33 , 22244 c3k , 22320 c or e1am , bearing 22324 , bearing 22334 , 32240 cc , bearing 30307 , bearing 30317 , 32311 a , bearing 32307 , bearing 32312 , bearing 32322 , bearing 31310 , sl 182926 , sl 182944 , sl 182972 , nj 318 , nj 2226 , qj 218 n2 , bearing 22316 , 23060 hlk with sleeve ah 3060 h , 23052 hlk with sleeve ah3052 h , 22215ek , 22218ek , 22220ek , 22222ek , 22224ek , 22230cc / w33 , 22211ek , 22217ek , 22212ek , 22228ek , 22232ek , 22226skmb , 23136e1akm , 23140ek ( cage steei ) , 32312j2 / q , ucf212 d1 , 22213ek , 22244k ( cage steei ) , 32310u , 32315u , 22230 ek , ucf 211 , ucf 210 d1 , ucf 213 d1 , 23144 ek , 23122 easkmc3 , nu 213 em1c3 , nu 316em1c3 , nu 315em1c3 , nu 318em1c3 , nu 321em1c3 , nu 320em1c3 , nu 322 em1c3 , nu 324 em1c3 , nu314 e / c3 , nj 2320 ecj / c3 , 6216 c3 , 3306 btvh , 3309btvhc3 , 6318 c3 , 6321 c3 , 6322 c3 , 6310 c3 , 6314 c3 , 6319c3 , 6324c3 , 6312 / c3 , total , kalisindh thermal power project, rvun, jhalawar , bearing 23238 , bearing 31330 , bearing 24048 , bearing nu238 , bearing 23138 , nu1080 , nu2368 , bearing 23168 , e60 xl krr , e 45 krr , ucf 209 , csa212 , cna209 , yar 210 2f , 6208 2rs , 6212 2rs , 6204 zz , 7319becb , nu316ecmp63 , 6316mc3 , nu234ecml / c3 , 6234m , nu2318 , h90381 / 90744 d , 22316 ck / w33 , nu316c3 , 6315c3 , 6319c3 , 6410 c3 , 6411 c3 , 6004 zz , 6203 2rs1 , 6204 zzc3 , 6205 zzc3 , 6206 zzc3 , 6208 zzc3 , 6209 2rs , 6210 zz / 2rs , 6213 2rs , 6221 em1c3 , 6305 zz , 6308 2z , 6310 zz / em1c3 , 6312 2rs / c3 , 6313 2rs / c3 , 6315 2rs / c3 , 6317 em1c3 , 6318 em1c3 , 6319 em1c3 , 6322 em1c3 , nu 221 em1c3 / epc / c3 , nu226 em1c3 / ecj / c3 , cylindrical roller bearing nj2317 ecml c4 , 22232 e1akm , 22216e1akm , 22256 bk.mb with adaptor sleeve oh3156 , bearing 6312 , 22210 e1kc3 , 22213 cck , bearing 7308 , bearing 7212 b , bearing 7305 , nu1020m1 , roller bearing nu218 , 3308 a / c3 , 32318 a , total , ramgarh gas thermal power project, rvun, ramgarh , 6203 zz , 6204 c3 , 6204 zz c3 , 6205 zz c3 , 6206 c3 , 6209 2rs , 6305 zz , 6308 zz c3 , 6304 zz , bearing 6305 , bearing 6308 , bearing 6310 , 6311 c3 , total => limited...

Rajasthan Rajya Vidhyut Utpadan Nigam Limited - Rajasthan

33192762 procurement of critical type bearings under category a2 against nit no. tn 07 / 2022 23 procurement of critical type bearings under category a2 against nit no. tn 07 / 2022 23 , chhabra thermal power project, rvun, chhabra , bearing 61840 , 22220e , 23220cc / w33 , 3311 bd ( 11j340 ) x life , bearing 71450 90045 , 6202.2z.c3 , 6204.2z.c3 , 6205.2z , 6205.2z.c3 , 6206.2z.c3 , 6206.2z , 6208.2z , 6208.2rs , 6209.2z.c3 , 6220.c3 , 6222.c3 , 6304.2z , 6306.2z.c3 , 6308.2z , 6308.2zr , 6308.zz.c3 , 6309.2z , 6309.zz.c3 , 6314.c3 , 6314.2rs , bearing 6317 , bearing 6318 , 7322bg , nu240.c3 , qj320.n2.mpa , rna4905 , nu318ecm , 6318.c3 , total , chhabra supercriticalthermal power project, rvun, chhabra , 22212 k / c3 + sleeve h312 , plummer block ( snv 110 f l ) with double lip seal and frm 110 ring , 22220 e1k / c3 ( with steel cage ) + sleeve h320 , bearing 6322 , 6310 c3 , 6315 c3 , 7314 bdb , 6209 c3 , 6322 c3 , 6319 c3 , nu 324 c3 , nu 1052 c3 , 7319 bm , 7334bg , 6234 c3 , ( de ) spherical roller skf 22220e , ( nde ) spherical roller 23 220cc / w33 , ( de ) deep groove ball bearing skf explorer: 7310 becbp ( austria ) , ( nde ) cylindrical roller bearing skf explorer: nu 310 ecj ( germany ) , suratgarh supercriticalthermal power project, rvun, suratgarh , nu1028mcylindrical roller bearing , nu1030m+6030c3 cylindrical roller bearing , nu 234 c3 , 2216 c3 self aligning ball bearing , 6203 2rs c3deep groove ball bearing , 6204 2z deep groove ball bearing , 6204 zzc3 , 6205 zz c3 deep groove ball bearing , 6206 zz deep groove ball bearing , 6206 zz c3 , 6207 zz deep groove ball bearing , 6208 2rs c3 deep groove ball bearing , 6209 zz deep groove ball bearing , 6209 zz c3 deep groove ball bearing , 6209 2rs deep groove ball bearing , 6210 zz , 6212 zz , 6212 c3 , 6212 z c3 deep groove ball bearing , 6213 2rs deep groove ball bearing , 6218 c3 deep groovball bearing , 6219 c3 deep groove ball bearing , 6220 c3deep groovball bearing , 6234 c3 deep groove ball bearing , 6283 zz c3 deep groove ball bearing , 6284 zz c3 deep groove ball bearing , 6304 zz , 6305 zz c3 , 6308 deep groove ball bearing , 6308 zz c3 deep groove ball bearing , 6309 zz deep groove ball bearing , 6309 2rs deep groove ball bearing , 6310 zz , 6312 zz , 6312 c3 , 6314 c4 deep groove ball bearing , 6315 c4 deep groove ball bearing , 6316 c3 deep groove ball bearing , 6317 c3 , 6318 c3 , 6319 c3 , 6322 c3 deep groove ball bearing , 6334 c3 , 7332 b deep groove ball bearing , 22216 / c3double row spherical roller bearing , 22224 ck spherical roller bearing , 22224 ck &3320 , 22240 cckc3 / w33 + h3140 spherical roller bearing , vob8494 / 240thrustbearing , sleeve #280 , total , suratgarh thermal power station, rvun, suratgarh , 6310 deep groove ball bearings , 6217 c3 deep groove ball bearings , 6221 c3 deep groove ball bearing , 6316 c3 deep groove ball bearings , 6205 2z deep groove ball bearing , 6206 2z deep groove ball bearing , 6308 deep groove ball bearing , 6308 2z deep groove ball bearing , 6309 zz c3 deep groove ball bearings , 6313 deep groove ball bearing , 6314 deep groove ball bearing , 6315 c3deep groove ball bearing , 6319 c3 deep groove ball bearings , 6316 2rsr deep groove ball bearing , 6208 deep groove ball bearings , 63112rsr deep groove ball bearing , 3311angular contact double row ball bearing , 3311 a / c3 angular contact double row ball bearing , 3310 a angular contact ball bearing , nu 222 e cylindrical roller bearing , nup222 e cylindrical roller bearing , nu226 emic3 cylindrical roller bearing , nu 311 general segment cylindrical roller bearing , n 213 e m1cylindrical roller bearing , nu 315 emi c3 cylindricalroller bearing , nu 310 emi c3 cylindricalroller bearing , n 316 em1cylindrical roller bearing , 71450 tapered roller bearing , 29415e spherical roller thrust bearing , 29344 e spherical roller thrust bearing , total , dholpur combined cycle power project, rvun, dholpur , 6209 2rs , total , mahi, rvun, banswara , ball bearing 6303 zz for jet pump , cylindrical roller bearing nu 318 ecp for power generator ( de ) , open deep groove ball bearing 6318 for power generator ( nde ) , cylindrical roller bearing nu 324 for power generator ( de ) , open deep groove ball bearing 6324 for power generator nde , total , kota super thermal power station, rvun, kota , 3310atn9 , 6413c3 , 6408c3 , bearing 6020 , 29326 e1 , 6004zz , 6202zz , 6205zz , 6205zzc3 , 6206zz , bearing 6208 , 6208 2rsr , 6208zz , 6212c3 , 6212zzc3 , 6213c3 , 6213 2rs , 6215c3 , 6224emc3 , 6304zz , 6305zz , 6307zzc3 , bearing 6308 , 63082rsr , 6308zz , 6308zzc3 , 6309zz , 6309 2rs , bearing 6310 , 6310zz , bearing 6311 , 6311zz , 6311 2rs , bearing 6312 , 6312 2 rs , bearing 6313 , 6313c3 , 6314c3 , 6315c3 , 6316c3 , 6316 2rs , 6317c3 , bearing 6318 , bearing 6319 , 6319c3 , 7206zz , 7322bg , nu305 , nu213 , nu214 , nu248m , nu316 , nu318 , nu319ecm , nu322 , nu326ecmc3 , nu1060 , 29356 ea , 3309 a , nu 309 ecp , bearing 6306 , nu 306 ecj , nu326ecm / c3 , 6326c3 , 6324c3 , nu 322 em1c3 , 6322 c3 , total , kalisindh thermal power project, rvun, jhalawar , bearing 22226 , bearing 7226 , 7311 acm , 6326m / c3 , nu226ecj / c3 , nu221ecp / c3 , 7320bebcm , 6248mc3 , 6232m / c3 , 7330bcbm , nu224ecj , bearing 6224 , nu 220ecj , 29452 e1 , 29320 e1 , 29318 e , total , ramgarh gas thermal power project, rvun, ramgarh , 6212 zz , 6213 2rs , 6313 c3 , 6316 2rs , nu 215 m , nu 313 c3 => limited...

Rajasthan Rajya Vidhyut Utpadan Nigam Limited - Rajasthan

33096958 purchase of critical type bearing category a1 ls against nit no. tn 06 / 2022 23 purchase of critical type bearing category a1 ls against nit no. tn 06 / 2022 23 , chhabra thermal power project, rvun, chhabra , bearing 6205.zz , bearing 6209.2z.c3 , bearing 6309.2z.c3 , bearing 6322.c3 , bearing nu322e.m1 , bearing 32308 , bearing 32310 , bearing 32316 , bearing 32222 , spherical roller 23060 cck / c3 / w33+hm3060+oh3060h+ms3060 ( adpter sleeve & lock nut ) , spherical rollerthrust 294 / 500 e , total , chhabra supercriticalthermal power project, rvun, chhabra , bearing 31316 trb , bearing nf217 mb , bearing 31322 x j2db trb , bearing 6056 dgb , bearing 6010rs1 , bearing 3010cm nsk , bearing 6308 2rs1 , total , suratgarh supercriticalthermal power project, rvun, suratgarh , 6212 2rs deep groove ball bearing , 6312 2rs deep groove ball bearing , total , suratgarh thermal power station, rvun, suratgarh , 6205 2z deep groove ball bearing , 6308 2z deep groove ball bearing , 6309 zz c3 deep groove ball bearing , total , mahi, rvun, banswara , spherical roller bearing23026 cc / w33 for gear box ( speed increasing ) , spherical roller bearing 23220 cc / w33 for gear box ( speed increasing ) , spherical roller thrust bearing 29322 e for gear box ( speed increasing ) , spherical roller thrust bearing 29412 e , spherical roller thrust bearing29416 e , spherical roller thrust bearing24122 cc / w33 for gear box ( speed increasing ) , bearing skf de 29324e , total , kota super thermal power station, rvun, kota , bearing 6204zz , bearing 6205zz , bearing 6209 2rs1 c3 , bearing 6309zz , bearing 6310 , total , kalisindh thermal power project, rvun, jhalawar , bearing 32209 , bearing 22309 , bearing 30309 , bearing 32312 , bearing 30319 , bearing 2007960 , bearing 32232 , bearing nna4905 , bearing 16005 , bearing 6208 , total , dholpur combined cycle power project, dholpur , a1 , b2 , total , plantx , total , plant y , total => limited...

Indian Army - Rajasthan

33048637 bids are invited for torsion damper , upper thrust bearing , lower thrust bearing , air pressure guage 044 10 kpa , conductor vru cable , sleeve assy , pressure plate assy , clutch plate , air pressure governor assy ,hood pump assy , cabin shocker , control valve ,fifth leaf , isolator switch total quantity : 34...

Rajasthan Rajya Vidyut Utpadan Nigam Limited - Rajasthan

32738757 supply of rollers and idlers frames for chp conveyor system at katpp, rvunl, jhalawar supply of rollers and idlers frames for chp conveyor system at katpp, rvunl, jhalawar , impact rollers for 1400 mm belt width, dimensions / specificationsas per approved drawing j1601 11 , carrying rollers for 2000 mm belt width, dimensions / specifications as per approved drawing j1601 19 , impact rollers for 2000 mm belt width, dimensions / specificationsas per approved drawing j1601 20 , v type two roll return rollers for 2000 mm belt width, dimensions / specificationsas per approved drawing j1601 21 , guide rollers, 100mm length , 60.30 mm dia with thrust bearing skf / fag of 51107 . dimensions / specifications as per approved drawing j1601 05. , 25 deg. impact idler for 2000 mm belt width, dimensions / specifications as per approved drawing j1601 16 , 10 deg. v type two roll return idler for 2000 mm belt width. dimensions / specifications as per approved drawing j1601 17...

Rajasthan State Road Transport Corporation - Rajasthan

32614622 rsrtc invites the tender for ball and tapper roller bearings rsrtc invites the tender for ball and tapper roller bearings , specifications of ball & tapper roller bearings as:190:81:march:2014, as:322:66:jan:2004 , pbg / 66 f0243210 / f0255010 needle roller bearing , pbg / 67 f0242510 / f0254010spigot bearing , pbg / 126 ib001825needle bearing 3rd ( b60049 ) , pbg / 127 ib001824needle bearing 1st ( b60047 ) , pbg / 128 ib001826needle bearing reverse ( b60048 ) , pbg / 119 ib003070 pilot bearing m / s eicher midi , pbg / 120 if000148 / bb60063 needle bearing 4th eicher midi , pbg / 122 if000864 / nup307 mnr needle bearing c / s , pbg / 121 if000863 / nup307 mn needle bearing c / s , pbg / 130 id200359 / jc 8022 bearing , pbg / 132 id200480 / bb60107 needle roller bearing 1st , pbg / 131 id200456 / bb60109 needle roller bearing 2nd , pbg / 129 id200349 / b60106 needle roller bearing reverse , pbg / 90 2691 2620 3106 needle cage bearing tata , pbg / 97 2516 2635 3104 roller ring ( rev idler gear ) , pbg / 141 id200457 bearing 3rd speed , pbg / 142 id200458 bearing 4th speed , pbg / 144 id200453 bearing drive pinion , pbg / 2691 2625 3113 roller thrust bearing arrgmt bs iii / 2017 , pbg / f0267310 bearing 6.s.850 , pbg / f0267510 bearing 6.s.850 , pbg / 79 f0267410 n.r. bearing , pbg / f0256310nr bearing 5th6.s. 850 , pbg / f0267710 input shaft bearing , pbg / 92 2691 2620 3111 needle cage bearing ist , pbg / jc 409025 pinion bearing lay , pbg / pop00150 pilot bearing r160 crb , pbg / hk4012 ntn bearing leyland , db142012p nr bearing...

Indian Army - Rajasthan

32526347 bids are invited for torsion damper , upper thrust bearing , lower thrust bearing , air pressure guage 044 10 kpa , conductor vru cable , sleeve assy , pressure plate assy , clutch plate , air pressure governor assy ,hood pump assy , cabin shocker , control valve ,fifth leaf , isolator switch , injector for 135kv total quantity : 46...

Indian Army - Rajasthan

32325649 bids are invited for torsion damper , upper thrust bearing , lower thrust bearing , air pressure guage 044 10 kpa , conductor vru cable , sleeve assy , pressure plate assy , clutch plate , air pressure governor assy ,hood pump assy , cabin shocker , control valve ,fifth leaf , isolator switch , injector for 135kv total quantity : 46...

Rajasthan Rajya Vidhyut Utpadan Nigam Limited - Rajasthan

32077925 procurement of spares of m / s jyoti ltd. make cw & acw pumps installed at 2x660 mw, csctpp, chhabra — a. pump name. cw pump make: jyoti limited: type. vmf pump ( ip229352 — 1 thurstpao ( setofsnos ) : 2 2 impeller shaft with sleeve — nos._ i bottom line shaft with sleeve nos. 4 top line shaft with sleeve nos 1 5 top shaft with sleeve nos. — 1 6 jounral pad ( set of 12 nos. ) set — 1 7 sleeve for impeller shaft ( set of 3 nos. ) set — 1 8 sleeve for top shaft ( set of 2 nos. ) set 9 thordan bearing housing nos. 1 1 10 cover for tiiordan bearing housing — nos. nos 1 11 12 imp! ler nut toyi’. wasi ep muff coupling 1 1 13 thrust bearing nos. 14 pump motor coupling fastners ( n1 set z12 nos. ) set 1 1 15 ( setof2nos. ) nos. 1 16 bowl. wearing ring 3 1 b. 1 impeller nut 2 pump name. acw pump; mnke: jyoti limited; rype: vt pump ( ip129 742 ) 3 4 line shaft bearing housing bowt bearing housing implll [ r nut lucj ( _wai1 s tune shaft with sleeve 6 isle eve for uune shwft iôs. 1a_. s. 3 nos. nos. 1 nos. 1 1 nos. 1 mpeller nut nos. line shaft bearing housing bowl bearing hous!ng impeller nut lock washer line shaft with sleeve sleeve for line shaft muff coupling top shaft with sleeve sleeve for top shaft gland impeller adjusting nut ratchet impeller shaft with sleeve sleeve for impeller shaft (set of 2 nos.) pump motor coupling fastners nos. nos. nos. nos. nos. nos. nos. nos. nos. 10 nos. 11 1 nos. nos. 12 set 14 (1 set set 15 ratchet pin suction bell ringg impeller back wearing ring (set of 2 nos.) bowl wearing ring etc ...

Rajasthan State Road Transport Corporation - Rajasthan

31325478 rsrtc invites the tender for exclusive parts tata through single source procurement rsrtc invites the tender for exclusive parts tata through single source procurement , exclusive items ( tata ) , 2724 2540 8601collector ring , 2786 1599 9902tensioner belt , 2786 2099 9925thermostate tc , 2786 0198 9924tube inj. fuel supply 1, 2, 3 , 2786 0198 9925tube inj. fuel supply 4, 5, 6 , 2786 1899 9905core cooler , 2786 2099 9973thermostate bs iii , 2786 0599 9978tappit valve , 2786 0599 9969valve intake , 2786 0599 9004 / 9968valve exh. , 2786 0599 9912support cam shaft , 2786 1899 9933oil pump , 2786 0599 9977 / 7902cam shaft , 2786 0199 9946 hose plain , 2786 0199 9910plug expension , 2786 0199 9907plug expension , 2786 0599 9979push rod , 2786 0599 9981assy rocker lever , 2786 2099 9996clutch viscus fan , 2786 0798 9922timing plate , 2778 3210 3702front spring bracket frt. rh , 2754 2560 5101clutch release yoke , 2786 0399 9972fly wheel housing , 2770 312 00115engine cross member frt. , 2770 312 00113engine cross member rear , 2786 2099 9937 / 96fan engine , 2573 3120 8216cross member , 2786 0399 9907sleeve wear , 2778 3210 3701front spring bracketfrt. lh , 2778 3210 3703front spring bracket rear lh , 2778 3210 3704frt spring bracket rear rh , 2778 3210 7701webeller rubber front spring , 2786 0199 9802main brg. 2nd tc , 2786 0399 0106main brg. 3rd tc , 8854 0302 1618engine overhauling kit , 2786 0799 6901 / 2786 0798 9949tube fuel drain , 2754 2510 3401clutch housing bush , 2786 0599 9970collect valve , 2786 0399 0196flywheel , 2786 0399 9911flywheel washer , 2786 0599 9971 / 9901retainer valve , 2786 1899 9944 / 9922plug expension , 2786 0399 9980 / 5701 0399 0105con. rod bearing std. , npncon. rod bearing rs i , npncon. rod bearing rs ii , 2786 0199 9801 / 2786 0399 0176main bearing tc std. , npnmain bearing tc rs i. , npnmain bearing tc rs ii. , 2786 0599 9980cross head valve , 2076 5000 0201radiator , 2786 0199 9916cylinder liner tata , 2527 0110 3727cylinder liner tata midi , 2786 0999 9921hose plain a / b type , 2576 2410 0101frt. engine mtg. pad tata , 2576 2420 0118rr. engine mtg. pad tata , 2576 4130 6301p.s. rubber pad , 2641 2410 0109engine mtg. pad frt. rh tata midi , 2641 2410 0110engine mtg. pad frt. lh tata midi , 2573 4130 7505c.b. rubber tata midi , 2786 5010 5819hose rubber radiator , 2786 5010 5840hose radiator , 2786 5010 5835hose radiator , 2786 0399 0150 piston set bare std. , 2786 0399 0153piston ring set std. , 2786 0399 0151 piston set bare rs i , 2786 0399 0154piston ring set rs i , 2576 4130 3301c.b. bracket , 2076 5010 0152radiator assly. , 2786 5010 0375 / 0337raiator assly. , 2786 5010 0301 / 0286reserve tank plastic , 2575 3570 7902rr. axle shaft , 2527 0399 0172piston set bare std. tata midi , 2527 0399 0173piston ring set tata midi , 2575 3530 5403 / 5405rr. axle shaft gear gbs 60 , 2575 3530 5101diff. spidergbs 60 , 2691 2625 3704gear box frt cover upper gbs 60 , 2691 2630 3703g.b.frt.cover lower gbs 60 , 2691 2620 7911main shaft gbs 60 , 2691 2620 4615 engaging sleeve gbs 60 , 2691 26200185gear 2nd speed gbs 60 , 2691 26200184 geat ist speed gbs 60 , 2691 26204616 / 4624engaging gear reverse gbs 60 , 2691 2620 3710 rear cover main shaft gbs 60 , 2691 2630 3702 rear cover counter shaft gbs 60 , 2691 26208203oil slinger gbs 60 , 2691 2651 6705doweling pin gbs 60 , 2507 2670 9902brass pad gbs 60 , 2691 2620 8612spacer gbs 60 , 2516 2635 6102th. washer gbs 60 , 2691 2651 9901brass pad gbs 60 , 2691 2625 0135drive shaftgbs 60 , 2691 2630 7904 / 09counter shaft gbs 60 , 2691 2625 0126drive shaftgbs 60 , 2691 2630 5423constantmesh gear gbs 60 , 2691 2620 0182syncro. kit gbs 60 , 2688 2620 4608shifter sleevegbs 60 , 2691 2630 54105th gear on c / shaft gbs 60 , 2691 2620 0186gear 3rd speed gbs 60 , 2691 2620 0187gear 4th speed gbs 60 , 2691 2620 0189gear 5th speed gbs 60 , 2691 2620 4640engaging gear 5th&7th gbs 60 , 2691 2620 4651syncro. conegbs 60 , 2691 2620 4621engaging gear gbs 60 , 2691 2620 4618shifter sleevegbs 60 , 2691 2620 4650syncro. conegbs 60 , 2691 2620 5413gear reverse gbs 60 , 2691 2630 5424c / shaft third gear gbs 60 , 2691 2630 5425c / shaft fourth gear gbs 60 , 2688 2620 5407speed drive gear gbs 60 , 2691 2620 8601spacer gbs 60 , 2515 2620 4312 circlip gbs 60 , 2691 2620 4306circlip gbs 60 , 2691 2620 4301circlip gbs 60 , 2691 2620 4313circlip gbs 60 , 2691 2620 8629spacer main shaft gbs 60 , 2691 2651 8703compression spring gbs 60 , 2691 2625 8205oil slinger gbs 60 , 2668 3530 0107 / 0130c.w. & pinion set gbs 60 , 2688 2620 6501lock nut gbs 60 , 2691 2620 0172assly.coupling flange gbs 60 , 2691 2625 3113roller set gbs 60 , 2668 3530 5439gear rear axle shaft gbs 60 , 2691 2620 0146assly. over drive gear , 2691 2630 5414over drive gear , 2691 2651 5125shifter fork , 2691 2620 4652clutch body , 2691 2620 4643clutch body , 2691 2620 46444th spd. synchro cone , 2691 2620 4624engine gear reverse , 2516 2678 8201cap selector shaft , 2691 2620 4605clutch body d / shaft , 8854 2601 2516detent pin kit , 2691 2651 7507shifter fork , 2691 2620 4645syn. cone , 2691 2620 4623syn. cone , 2691 2620 4635syn. cone , 2691 2620 3426speedo adaptor ( rear cover upper ) 2017 model , 2691 2620 7910speedo pinion ( rear cover upper ) , 2691 2620 8203oil slinger ( rear cover ) , 2516 2671 3705gear case cover top ( upper half ) , 2691 2670 7903selector & shifter shaft rhd , 2691 2671 5101shifter finger , 2691 2671 8702compression spring inner , 2691 2671 8701compression spring outer , 2505 2670 6009shifting lever , 2691 2651 7907shifter shaft 5th / 6th , 2691 2651 5123shifter dog finger 5th / 6th , 2691 2651 5120swing fork 5th / o.d. , 2691 2651 9901brass pad , 2691 2651 7910shifter shaft 3rd / 4th , 2691 2651 5116shifter dog 3rd / 4th , 2691 2651 7908shifter shaft 1st / 2nd , 2691 2651 5115shifter dog 1st / 2nd , 2691 2651 7918shifter shaft reverse speed , 2691 2651 5118shifter dog reverse , 2691 2651 5113shifter fork reverse , 2574 4910 0110silencer muffler, tata , 2786 0599 9966inlet valve bs iii , 2651 3210 6704frt. spg. shackle pin , 2651 3240 3401frt. spring bush , 2640 3240 6702rr. spring shackle pin , 2640 3240 3401rear spring bush , 2643 3220 4201frt. spring u bolt , 2644 3250 4203rr. spring u bolt , 1205 239 6067nut for u bolt , 1205 239 6075nut for u bolt , 2821 3320 6701king pin std , 8854 3319 0709king pin kit std. , 2641 4010 6703wheel bolt , 1205 169 6059wheel nut , 5507 4010 6702rear wheel bolt , 2525 2010 0124assy. water pump , 2525 2010 0119water pump repair kit major , 2641 3320 0121tie rod , 2641 3320 0135assy ball joint lh , 2641 3220 0136assy ball joint rh , 2651 3320 6304dust cap tie rod , 2651 4110 0128u.j.cross kit , 2632 4370 0115frt. brake diaphragm , 2821 4210 3702rear brake drum , 2574 3340 3701hub cover front , 2763 2540 0102310 dia assy. pressure plate , 2527 2311 0103steering oil pump midi , 2654 4620 8711compressor spring for stg. , 2641 4621 0136power stg. gear box rep. kit major , 2651 4660 0102u.j.cross stg. , 2786 0999 9951diesel fuel stainer , 2786 0399 0176con. rod brg. std. , 2641 2910 0189brake pedal assly. , 2527 0312 3119main brg. set , 8854 0343 2534con. rod brg. std. , 2534 2015 6323cogged belt 980 length , 2534 2010 6310v. belt ( cogged ) 925 , 2525 2015 6305fan belt , 2640 3210 0105assly. shackle with bush , 2527 1451 0120turbocharger assly. , 2527 5011 0130radiator assly. , 2661 3570 7903rear axle shaft , 2770 0100 0102engine assly. complete , 2691 2601 0155gear box assly. gb 60 , 2691 2601 0150gear box assly. gb 60 ( over drive ) , 2778 3300 0101frt. axle assly. tata , 2668 3500 0205rear axle assly. tata , 2786 0199 0311short block w / o cyl. head ( with internal fitting ) , 2786 0199 0110cylinder block , 2651 3210 6704frt. spg. shackle pin , 2651 3240 3401frt. spring bush , 2640 3240 6702rr. spring shackle pin , 2640 3240 3401rear spring bush , 2525 2010 0124assy. water pump , 2525 2010 0119water pump repair kit major , 2574 3340 3701hub cover front , 2763 2540 0102310 dia assy. pressure plate , 2654 4620 8711compressor spring for stg. , 2651 4660 0102u.j.cross stg. , 2786 0999 9951diesel fuel stainer , 2527 0100 0368engine assly. complete , 2786 0399 0176con. rod brg. std. , 2641 2910 0189brake pedal assly. , 2527 0312 3119main brg. set , 8854 0343 2534con. rod brg. std. , 2640 3210 0105assly. shackle with bush , 2527 0399 0172piston set std , 2527 0399 0173piston ring set std , 2527 5011 0130radiator assly. , 2661 3570 7903rear axle shaft , 2786 0199 9902bush cam shaft , 2786 0399 3401con. rod bush , 2786 1499 9942exh. manifold clip , 2507 2670 0152sub assy ball socket , 2848 2910 0122cmc steel pipe , 2770 2681 0101gear lever stand , 2786 1399 9904con. rod bearing set , 2651 4660 3401needle bush rs 1 , 8854 0358 2527piston set tata midi , 8854 0360 2527 piston ring set tata midi , 2632 5420 9903tempreture switch , 2654 5450 9913oil pressure switch , npnrecone engine assy tata bs iii , 2691 2625 3105cylinder roller bearing , 2691 2620 3120needle cage double row bearings , 2691 2620 3106needle cage rev. gear bearings , 2691 2620 3103tapper roller bearings , 2691 2620 7814g b oil seals , 2691 2625 3113roller thrust bearings , 2651 3530 7701oil sel tp , 2691 2620 0143assy neddle cage bearings , 805345 / gb 356437fan support bearings , 2786 2099 0153water pump assy bs iii , 2525 2010 0124water pump assy midi , 2691 2630 54136th counter gear over drive , 2691 2651 7918shifter shaft reverse , 2786 0199 9905plug expension , 2691 2651 7907shifter shaft 5& 6 , 2576 3340 3104 / 3101front huib inner bearing , 2573 3530 3109 / 0009818601 / nu 307mnwtail pinion bearing , 2691 2620 0142neddle cage bearing , 2691 2630 3104tapper roller bearings , 2676 3320 3109king thrust bearing t151 , 2690 2620 3106 / 3131needle cage bearing 1st , 5812 2560 1602clutch release bearing , 2574 4100 0000centre bearing tata midi , 2516 2635 3104roller ring , 2525 0161 0173assy. engine complete bs iv , 2525 0199 0262assy. long block bs iv , 2525 0116 0140assly. fuel injectors bs iv , 2525 0199 0264assy. half block bs iv , 2525 0117 0313assly.oil seperator bs iv , 2525 0199 0266engn. over haul gasket kit bs iv , 2525 0199 0267decarbonising gasket kit , 2525 0110 0313cylinder block assy.w / o clutch housing , 2525 011 63809air intake elbow , 2525 0115 5336gasket , 2525 0115 5355gasket rocker arm cover , 2525 0114 6301gasket , 8854 0504 2525cam shaft bearing set , 8854 0398 2525set inlet & exh. valve , 2534 0515 3402valve guide inlet std , 8854 0397 2525valve seat ring std , 2534 0515 3415valve guide exh. std , 2525 0114 0186assy. timing gear hsg. , 2534 0310 7801oil seal crank shaft frt. , 2525 2510 3745clutch housing , 2525 0311 8203back cover , 2525 0311 8204cover , 5710 1520 9903cam sensor , 5710 1520 9902crank sensor / speed sensor , 2525 0311 0141assy. fly wheel with ring gear , 352 032 1105ring gear , 2525 0310 7940crank shaft , 3520 520 003crank shaft gear , 2525 0313 8201oil slinger , 2525 0313 8603spacer , 8854 0308 2525kit crank shaft sealing ring , 2525 0312 0159set main bearing , 8854 0376 2525thrust washer set std , 8854 0377 2525thrust washer set rs i , 8854 0378 2525thrust washer set rs ii , 2525 0399 0165set con rod bearing std , 8854 0368 2525con rod bush set std , 2525 0399 0197piston set bare std , 2525 0399 0188piston ring set std , 2534 0310 3102ball bearing , 2525 0510 0145assy. cam shaft with cyl. pin , 3520 520 762thrust washer , 2525 0713 0123assy. cam shaft gear & drive gear , 2534 0513 9902tappet valve , 3520 540 205valve push rod inlet & exh. , 2525 0712 5302gasket , 2527 0911 0136protect filter , 2525 1451 0145assy. turbo charger , 2525 1411 5301gasket , 2525 1412 3703exh. manifold cowl , 2525 1411 0136assy. gasket exh. manifold , 2525 1411 0135assy. gasket exh. manifold , 2525 1410 0101assy. gasket intake manifold , 2525 1411 0235assy. egr cooler , 2525 1411 5314gasket , 2525 1411 0281assy. egr valve 24 v , 2525 1470 0167assy. inlet line , 2525 1514 6303poly v belt 1260l , 5033 5420 9904ems ecu for 697 dicor engn. , 2525 1810 0148assy. oil pump with strainer , 2525 1810 0144assy. oil pump w / o strainer , 2525 1810 3704housing , 2525 1810 7902drive shaft oil pump , 2525 1810 5405drive shaft ( 50mm ) , 2525 1810 7901shaft for drive gear , 3521 840 329valve hsg. , 2525 1815 0140assy. strainer , 3121 860 080gasket , 8854 1808 2525gear kit oil pump , 8854 1804 2525oil pressure relief valve kit , 2525 1813 0166assy. oil filter head , 2654 5450 9913low oil pressure switch , 2534 1813 5301gasket , 2525 1817 0232assy. oil cooler , 2525 1817 0150assy. relief valve , 2525 2010 0180assy. water pump , 2527 2010 5310w. p. gasket , 2525 2014 0153assy. viscous fan 550 dia , 2525 2014 7028water pump pulley , 2525 2012 0248assy. thermostate 35 dia , 2525 2314 6313v belt coggerd 1060l , 2618 4660 0101power steering pump assy. , 2525 2311 0122assy. bracket , 2525 2340 7006pulley , 2525 2314 6316v belt coggerd 995l , 2576 2410 0101frt. engn. mtg. pad , 2724 2520 0151clutch plate 330 dia , 2724 2540 0143clutch cover assy. 330 dia , 2724 2560 0160assy. clutch release bearing , 2724 2560 5106clutch release fork , 2724 2560 0115assy. bracket out side rh , 2505 2605 0154gear box assy. gbs 40 , 2505 2610 3723gear box housing , 2505 3014 5301gasket frt. cover lower , 2505 2630 8201housing cover frt. lower , 2505 2625 5301gasket frt cover top to hsg. , 2505 3013 4701gear box hsg. cover frt. top , 2505 2625 7808oil seal drive shaft , 2505 2620 7803oil seal , 2668 3515 0102pressure relief valve , 2505 2670 5105shifter fork ist speed , 1595 3520 131needle roller bearing 2x13.8 , 321 265 0805selector shaft ist speed , 321 265 1805selector shaft 2 / 3rd speed , 321 265 1905selector shaft 4 / 5th speed , 322 265 0305selector shaft reverse , 322 265 0123gear shift dog 1st gear , 321 265 1205selector fork 2 / 3rd , 2505 2651 5102selector fork 4 / 5th , 321 265 1301selector fork 1st , 2505 2651 5101selector fork reverse , 2505 2671 3756top cover , 2507 2671 3105needle bearing , 2505 2670 5104shifter finger , 2505 2670 7908selector & shifter shaft , 1706 160 2518oil seal , 2507 2670 6014shifting lever , 2506 2671 5301gasket kit , 2505 2600 0101kit gasket gear box , 2505 2625 7910drive shaft , 000 981 1201cylinder roller bearing nu 309n , 2505 2620 3106four point ball bearing , 2505 2625 3118roller cage , 2505 2620 7903main shaft pilot bearing , 340 262 0134syn. ring , 2505 3015 5403syn. sleeve 4 & 5th , 2505 2620 3802syn. cone , 321 262 0823shifting sleeve , 2505 3015 0105assy. helical gear 4th speed , 2505 2620 3123double row needle cage , 2505 2620 3124double row needle cage , 322 260 0644assy. helical gear 3rd , 322 262 0435syn. sleeve 2 / 3rd , 322 262 0112helical gear 2nd ( t 32 ) , 322 263 0333reverse gear main shaft 36t , 321 262 0723shifter sleeve 1st , 2505 3015 5401gear wheel 1st speed t 39 , 2505 2620 0176gear drive oil slinger , 2505 2620 7902drive shaft , 2507 2620 5001coupling flange ( 8 holes ) , 2505 2630 7906counter shaft , 2505 2630 54142nd gear counter shaft , 2505 2630 54153rd gear counter shaft 23t , 2505 3014 54014th gear on counter shaft , 2505 3014 5402constent mesh gear , 2505 2630 3104tapper roller bearing , 2505 2635 0106assy. reverse idler gear ( en 36 ) , 2505 3017 7901reverse idler gear shaft , 8854 2604 1612syn. kit , 2165 2680 0111assy. self & shifter yoke & fork , 2651 4660 3401needle bush , 2630 2680 8601spacer , 2641 2680 0224assy. ball joint rh , 2641 2680 0225assy. ball joint lh , 2641 2910 0117cmc assy. ( 19.05 dia ) , 2724 2560 5106clutch release fork , 302 991 0015ball pin , 2699 2910 0177cmc repair kit major , 2651 29100148cmc repair kit minor , 2754 32103201frt. center bolt , 1205 150 1207nut center bolt m12 , 352 320 0063frt. spring shackle , 2770 3210 3401frt. spring bush , 352 322 0530frt. spring pin , 2573 3210 6701frt. spring pin , 2573 3210 0107assy. sealing ring , 042 990 0037jcotter pin , 2770 3220 4203u bolt l 280 , 2618 3240 3202rear center bolt , 352 320 0163rear spring shackle , 2770 3240 3402rear spring bush , 352 325 0530rear shackle pin , 2575 3320 3401king pin bush , 2575 3320 9203 thrust washer upper , 2575 3320 9207thrust washer lower , 2846 3320 3101tapper roller th. bearing , 2576 3320 6707king pin cotter pin , 2632 3340 0104frt. hub assy. , 2576 3340 3103tapper roller bearing outer , 2576 3340 3101tapper roller bearing inner , 5030 3340 7801oil seal , 2631 4010 6701frt. wheel bolt m 22 , 2776 4210 3703frt. brake drum , 8854 3316 1612king pin repair kit minor std , 8854 3301 1612king pin repair kit minor 1st o / s , 8854 3302 1612king pin repair kit minor 2ndo / s , 8854 3303 1612king pin repair kit minor 3rdo / s , 5014 4210 9902kit cam end spring , 2880 4210 6701fulcrum pin , 5006 4210 0155front brake shoe assy. , 2573 4211 3210frt. mtg. bolt , 5014 4210 5101cam shaft lh , 5014 4210 5102cam shaft rh , 2786 0399 0246crank shaft engine w / gear 6 bt tata bs iii , 8854 4201 1512front brake lining set std. ( set of 8 pcs. ) , 8854 4202 1512front brake lining set 1st o / s ( set of 8 pcs. ) , 8854 4203 1512front brake lining set 2nd o / s ( set of 8 pcs. ) , 8854 4219 0709brass rivet long ( set of 48 nos. ) , 8854 4220 0709alluminium rivet long ( set of 48 nos. ) , 8854 4204 1512rear brake lining set std. ( set of 8 pcs. ) , 8854 4205 1512rear brake lining set 1st o / s ( set of 8 pcs. ) , 8854 4206 1512rear brake lining set 2nd o / s ( set of 8 pcs. ) , 2631 4020 6701rear wheel bolt m22 , 3668 3560 7703oil seal double , 2576 3560 3101tapper roller bearing inner rear , 2575 3560 3110tapper roller bearing outer rear , 2776 4230 3714rear brake drum , 2575 3570 7902rear axle shaft , 2576 3560 5301gasket , 2575 3530 5101differential spider , 2668 3530 5440diff. bavel pinion , 2575 3530 9201spherical washer , 2575 3530 3102tapper roller bearing , 2668 3530 0233c.w. & pinion assy. , 2573 3530 3109cylindrical roller bearing , 2060 3501 3001tapper roller bearing , 2668 3530 6501threaded ring , 2732 3530 0187assy. coupling flange 130dia , 2574 3315 0102breather assy. , 2776 4299 0109rear brake shoe assy. , 2776 4230 5102rear cam shaft lh , 2776 4230 5103rear cam shaft rh , 2880 4210 3403bush , 5040 4230 9909kit roller , 2631 4010 0107assy. wheel nut m 22 , 2750 4111 5101flange yoke , 2750 4130 0101center bearing kit , 2750 4130 3322center bearing bracket , 2632 4111 6301center bearing rubber , 2750 4111 5102companion flange , 2778 4230 0190automatic slack adjuster , 2776 4230 0230auto. slack adjuster rear lh , 2776 4230 0231auto. slack adjuster rear rh , 2778 4230 0165major repair kit slack adjuster , 2651 4660 0102assy. universal joint , 2063 4630 5104pitman arm , 2632 4600 0103drag link assy. , 2618 4660 0110seal kit , npnpiston set bare rs 1 , npnpiston set bare rs 2 , npnpiston ring set rs 1 , npnpiston ring set rs 2 , 2618 3240 0107rear main leaf , 2618 3240 7127rear 2nd leaf , 2618 3240 7128rear 3rd leaf , 2618 3240 7129rear 4thleaf , 2618 3240 7130rear 5th leaf , 2618 3240 7131rear 6th leaf , 2618 3240 7132rear 7th leaf , 2618 3240 7133rear 8th leaf , 2618 3210 0109front main leaf , 2618 3210 7111front 2nd leaf , 2618 3210 7112front 3rd leaf , 2618 3210 7113front 4thleaf , 2618 3210 7114front 5th leaf , 2618 3210 7115front 6th leaf , 2618 3210 7116front 7th leaf , 2618 3210 7117front 8th leaf , 2632 4210 3403sensor bush abs , 2643 5420 9929sensor l type frt. ( wheel speed ) , 2808 4210 3401sensor sleeve frt. , 2808 4230 3301sensor axle bracket rear , 2808 4230 3303sensor mounting bracket rear , 2163 5462 0221wiring harness battery cut off switch , 2165 5462 0101wiring harness sensor , 2165 5462 0102wiring harness engine for egr , 2165 5462 0110wiring harness dps inter connection , 2165 5462 0114main wiring harness , 2780 5420 9938speed sensor 12v / 24v , 2816 5421 0125ecu abs8, 4s / 4m 24v , 2525 0911 9903temperature sensor , 2525 1520 9901boost pressure sensor , 2525 1520 9905hfm sensor , 2527 0911 9911water level sensor , 2527 0911 9912temperature sensor , 2641 5420 9962water temperature sensor , 2525 1520 9906dps sensor , 2632 4210 3403sensor bush abs ( knoor ) , 2782 4210 0106brake chamber type 24 , 2632 3910 0174repair kit brake chamber type 24 , 2752 4370 0108spring brake actuator type 24 / 24 , 5042 4399 0105spring brake actuator t24 / 24 major , 2778 4370 0165air dryer 9 bar osc cartridge , 5053 43900176air dryer cartridge , 2632 4371 0102repair kit air dryer , 2632 43700142four circuit prot. valve , 2632 4370 0104major repair kit four circuit prot. valve , 2632 4371 0145minor repair kit four circuit prot. valve , 2880 4370 0194rg2 relay valve , 2782 4370 0189repair kit relay valve , 2846 4371 0109dual treadle valve , 2632 4391 0168repair kit dual brake valve , 2163 4370 00252quick release valve , 4103 4370 9910repair kit quick release valve , 2770 3010 0138accelerator cable assy. , 5028 3010 0106assy. pull cable accelerator , 2525 1810 0148assy. oil pump with strainer , 2525 1810 0144assy. oil pump without strainer , 2786 0799 6905tube fuel supply bs iii 2017 model , 2786 0799 6901tube fuel drain bs iii 2017 model , 2786 0799 6904tube fuel supply bs iii 2017 model , 2523 0117 6937tube bs iii , 2525 0714 0204assy. fuel pressure line 1 ( bent ) fip , 2525 0714 0243assy. fuel pressure line 1 ( bent ) rail to inject , 2525 0714 0205assy. fuel pressure line 2 ( bent ) fip , 2525 0714 0244assy. fuel pressure line 2 ( bent ) rail to inject , 2525 0714 0245assy. fuel pressure line 3 ( bent ) rail to inject , 2525 0714 0246assy. fuel pressure line 4 ( bent ) rail to inject , 2525 0714 0247assy. fuel pressure line 5 ( bent ) rail to inject , 2525 0714 0248assy. fuel pressure line 6 ( bent ) rail to inject , 2525 0912 0307assy. over flow line rail to accumulator , 2525 0912 0306assy. over flow line pump to accumulator , 2525 1817 0205assy. lube line flexible , 2525 1813 0162assy. oil line oil filter to fip , 2527 1817 0128assy. lube line oil filter to fip , 2651 4660 0102assy. universal joint bs iii / iv , 2067 4660 0105assy. universal joint bs iii / iv , 2641 2680 0224assy. ball joint rh bs iii / iv , 2641 2680 0225assy. ball joint lh bs iii / iv , 2785 5010 5803hose ( 20idx110l ) bs iv , 2525 5010 5865hose water fill pipe ( 20idx90x105 ) , 2525 5011 5811hose radiatorto w.p. , 2525 5011 5857rubber hose ( th. to radiator ) , 2525 5011 5858vent hose ( radiator to th. ) , 2786 0599 9906hose plain bs iii , 2786 1899 5803hose elbow bs iii , 2525 0117 5809hose oil separator bs iv , 2786 0599 9967insert valve 2017 model , 5701 0599 9001valve exhaust , 5701 0599 8701spring valve , 2786 0599 9973seal valve steam , 2786 0599 4701cover valve , 2770 3230 0102assy. frt. shock absorber , 2574 4323 0104assy. bracket frt. shock absorber , 042 323 0063 jshock absorber mtg. bracket lower , 2574 3230 8602bush frt. shock absorber , 2786 2099 9995fan engine 2017 model , 2076 0101 0109engine assy. complete bs iii 2017 model , 2786 0199 0212long block bs iii 2017 model , 2786 0199 9906plug expansion , 2786 0199 9915plug expansion , 2786 0599 9937plug expansion , 2786 0198 9911plug expansion , 2863 0199 9922plug expansion , 2786 0599 0108housing gear , 2786 0399 5402gear fly wheel ring , 2786 2099 9828thermostat , 2505 2605 0154assy. gear box gb 40 bs iv , 2505 2610 3727gear box housing bs iv , 2691 2610 0167assy. housing rear & front half 2017 model , 2163 3300 0112front axle assy. 2017 model , 2668 3500 0282rear axle assy. with brake , 3163 3300 0114front axle assy. bs iv , 2668 3500 0276rear axle assy. complete bs iv , 2165 2910 0120assly.clutch booster bs iv , 2525 1411 0262assly egr pipe ( cooler to elbow ) , 2525 1411 0337assly egr pipe ( cooler to elbow ) , 2525 2012 0310thermostat assly. , 2525 2012 5841rubber hose , 2525 5050 6348fan shroud jetring , 5027 4680 0105assly pressure pipe ( pump to gb ) , 5027 4680 0106assly return pipe ( gb to tank ) , 5027 4680 0107 assly suction pipe , 2691 2620 8628spacer main shaft , 352 1310 280gasket sleeve to head , 2525 2314 3706bracket , 2525 1460 5814hose ( ic pipe to intake elbow ) , 2839 2910 0102assly clutch pipe , 2525 2012 5842rubber hose , 2525 0914 0219air intake pipe , 2525 1460 6967pipe ( tc adapter to ic ) , 5030 4660 0105assly stg plastic reservoir , 2782 4440 0101assly hydraulic stg tank plastic , 2525 1460 4201 coated clamp ( for ic pipe ) , 2163 5460 0166 pigtail abs wiring harness , 2754 2560 5101 clutch release yoke , 2750 4610 0101assly bktstg gear box mounting , 2573 3511 0106assly.carrier housing , 2808 4640 0101assly steering wheel , 2525 2014 0154 assly jetring fan , 2668 3560 0109assly rear hub ( w / o brg & seal ) , 2163 4371 0118air dryer , 2732 3530 0183diff housing assly , 2525 0116 3809 air intake elbow , 57091 4105 5303gasket ( intake monifold toheator flange , 27860913 0134air filter assly. bs iv , 2786 0913 0297assly.strap with shackle , 2525 0914 0190assly. pipe with flange , 2525 1460 6961pipe ( ic to intake elbow ) , 2194 5420 9962instruments cluster assly. bs iv , 2592 6890 0106assly. ip & ip cover...

Rajasthan State Road Transport Corporation - Rajasthan

31252330 rsrtc invites the tender for ball and tapper roller bearings rsrtc invites the tender for ball and tapper roller bearings , specifications of ball & tapper roller bearings as:190:81:march:2014, as:322:66:jan:2004 , pbg / 01 2576 3340 3103 tapper roller bearing32308 bs iv / frt hub outer bearing bs iii / 2017 , pbg / 02 2576 3340 3104 / 3101 ( t ) / 513615 3640 tapper roller bearing565 562 bs iv / frt hub inner bearing bs iii / 2017 , pbg / 18 000 981 8601 ( nu 307 mnw ) / 2573 3530 3109 ( t ) cylinder rollerbearing bs iii / 2017 , pbg / 51 2575 3560 3101 / 2575 3560 3110 tapper roller bearing 32214, bs iv / rr. hub outer bearing bs iii / 2017 , pbg / 52 2575 3560 3103 / 2576 3560 3101 tapper roller bearing 33019, bs iv / rr. hub inner bearing bs iii / 2017 , pbg / 53 2574 4130 3104 / 3114 p.s. centre bearing ( 6211 ) , pbg / 88 2691 2620 0143 / 3125 / 3133 bb455236 fs assy. needle cage bearing , pbg / 89 2691 2620 0142 / 3124 / 3130 bb728040fs assy needle cage bearing , pbg / 91 2691 2620 3120 / 3123 / 3132 bb 808840fsneedle bearing , pbg / 96 / 123 2691 2630 3104tapper roller bearing25572 25520, bs iii / 2017 , pbg / 101 2186 3310 3127ft. hub outer bearing eicher big ( 32309 ) , pbg / 103 2576 3560 3102 / 3103 ft. hub inner bearing eicher big ( 33215 ) , pbg / 105 000 981 9605 / 2641 3340 3103ft. hub outer eicher midi ( 32307 ) , pbg / 104 2664 3375 3108ft. hub inner bearing eicher midi ( 33111 bc ) , pbg / 102 2661 3560 3101 / 2612 3560 3102rr. hub outerbearing eicher / tata midi ( tx32212 ) , pbg / 25 f0232810 frt.hub outer bearing ( 535 532 ) , pbg / 26 f0232910frt. hub inner bearing ( 6379 6320 ) , pbg / 27 f0230310rr. hub outerbearing ( 563 566 ) , pbg / 28 f0230110 rr. hub inner bearing ( 580 572 ) , pbg / 37 f0230010tapper roller pinion bearing ( 72212 / 72487 ) , pbg / 85 p4900402 / mub 7307 / jc 8035 tail pinion bearing bs ii , pbg / 48 f0245410 pilot bearing hino ( 6203 2rs ) / bs iv alternator , pbg / 57 6303 2rsd.e. bearing alt bs iii , pbg / 58 2576 3320 3109 / f0256910 / t 151 king pin thrust brg.std , pbg / 60 6201 2rs alternator bearing tc , pbg / 63 f0253810clutch release brg.ley. bs iii ( 6212 lu ) , pbg / 66 f0243210 / f0255010 needle roller bearing , pbg / 67 f0242510 / f0254010spigot bearing , pbg / 68 f0243010 / f0254610needle roller bearing 1st , pbg / 69 f0242710 / f0254910needle roller bearing bb44545fs , pbg / 70 f0242910 / f0254810needle roller bearing 3rd , pbg / 71f0243110 / f0254710 needle rollerbearing 1st bb627040 , pbg / 72 f0242410 / f0259310roller bearing ( nup 309em ) , pbg / 73 f0248510 / f0254510taper rollerbearing ( 2789 2729 ) , pbg / 74 f0248610 / f0254210 taper rollerbearing ( 344 332 ) , pbg / 75 f0242810 / f0254310 needle roller bearing reverse , pbg / 76 f0242610 pinion bearing ( nup 12097 ) , pbg / 77 p4501139 209 yy 2 nrb p.s. centrebearing / bs iv , pbg / 83 p4900202 diff. pinion bearing ( 493 497 ) , pbg / 109 f0259210 / jc 8020 cyl. roller bearing ips , pbg / 99 f0246010 tapper bearing ( 567 563 ) , pbg / 100 55200 / 55437 tapper bearing zf , pbg / 106 f0245910 rear hub outer brg.ley. midi ( 3982 3920 ) , pbg / 108 f0244610 front hub inner brg. ley. midi ( 39581 39520 ) , pbg / 116 f0244710 front hub outer brg. ley. midi ( 3490 3420 ) , pbg / 112 f0259410king pin thrust bearing ley.midi ( t 126 ) , pbg / 110 mb563234ps center bearing eicher ( tx 7240 ) , pbg / 39 f 0238910 / 6305 lufly wheel bearing tc , pbg / 113 id305142 clutch release bearing eicher midi , pbg / 126 ib001825needle bearing 3rd ( b60049 ) , pbg / 127 ib001824needle bearing 1st ( b60047 ) , pbg / 128 ib001826needle bearing reverse ( b60048 ) , pbg / 119 ib003070 pilot bearing m / s eicher midi , pbg / 120 if000148 / bb60063 needle bearing 4th eicher midi , pbg / 122 if000864 / nup307 mnr needle bearing c / s , pbg / 121 if000863 / nup307 mn needle bearing c / s , pbg / 130 id200359 / jc 8022 bearing , pbg / 132 id200480 / bb60107 needle roller bearing 1st , pbg / 131 id200456 / bb60109 needle roller bearing 2nd , pbg / 129 id200349 / b60106 needle roller bearing reverse , pbg / 114 f0258210 / tx 92al clutch release bearing ley.midi , pbg / 03 tx 32213 crown pinion bearing , pbg / 117 tx 30309 pinion bearing eicher midi , pbg / 118 ia201080 pinion pilot wheel brg. , pbg / 124 31308 taper roller bearing , pbg / 125 31309 / id 345400 taper roller bearing , pbg / 140 6308 n / c3 / me601855 ball bearing with snap ring , pbg / 65 805345 fan support bearing tata , pbg / 86 2691 2625 3105 cylinder rollerbearing ar7.5 75 100, bs iii / 2017 / 2013 , pbg / 87 2691 2620 3103 / tapper roller bearing 28580 / 521 bs iii / 2017 / 2013 , pbg / 90 2691 2620 3106 needle cage bearing tata , pbg / 97 2516 2635 3104 roller ring ( rev idler gear ) , pbg / 141 id200457 bearing 3rd speed , pbg / 142 id200458 bearing 4th speed , pbg / 143 id200466 bearing counter shaft nup309 , pbg / 144 id200453 bearing drive pinion , pbg / 145 id200455 bearing main shaft nup310 , pbg / 2786 0399 9944pilot bearing bs iii / 2017 , pbg / 2691 2625 3113 roller thrust bearing arrgmt bs iii / 2017 , pbg / f0267310 bearing 6.s.850 , pbg / f0267510 bearing 6.s.850 , pbg / 79 f0267410 n.r. bearing , pbg / f0256310nr bearing 5th6.s. 850 , pbg / f0267710 input shaft bearing , pbg / 147 / 22 206035013001 tapper rollerbearing 31312l bs iii / 2017 , pbg / 54 2573 3530 3101 / 47487 / 20 diff.cage bearing , pbg / 92 2691 2620 3111 needle cage bearing ist , pbg / f0256610 ball bearing zf ley , pbg / jc 409025 pinion bearing lay , pbg / h715334 crown bearingley , pbg / h715343 crown bearing , pbg / jc 8017a bearing leyland , pbg / 148 47820 890 crown bearing , pbg / pop00156 inner bearing cup & cone r149.5 , pbg / pop00150 pilot bearing r160 crb , pbg / pop00140 bearing cup&cone r149 , pbg / pop00144 roller bearing r149 crb , pbg / hk4012 ntn bearing leyland , db142012p nr bearing...

Nuclear Power Corporation Of India Limited - Rajasthan

30893163 supply of aop and eop equipment for lube oil system and plant startup. 1 supply of suction strainer, part no : 2, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 2 2 supply of impeller nut, part no : 3, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 3 3 supply of impeller key, part no : 4, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 4 4 supply of neck ring, part no : 6, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 6 5 supply of shaft sleeve, part no : 8, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 9 6 supply of pump brg bush, part no : 9, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 9 7 supply of pump shaft, part no : 11, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 11 8 supply of brg spacer, part no : 13, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 13 9 supply of thrust bearing ( skf or fag 3313 ) , part no : 14, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 14 10 supply of skf brg washer, part no : 15, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 15 11 supply of bearing cover, part no : 16, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 16 12 supply of coupling key, part no : 17, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 17 13 supply of flexible coupling, part no : 18, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 18 14 supply of gasket ( for casing / delivery pipe ) , part no : 22, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 22 15 supply oforing for casing, part no : 23, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 23 16 supply of gasket ( for casing / suction pipe ) , part no : 26, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 26 17 supply of adjusting ring, part no : 27, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 27 18 supply of brg carrier, part no : 31, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 31 19 supply of skf lock nut, part no : 32, for auxiliary oil pump, make: wilo mather and platt model no : pnv 31 sr no: 81252045 / 42 as per the npcil drg no:rapp 7&8 / 41332 / 6002 / ga / r2, ref 32 20 supply of impeller nut, part code : 3, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 3 21 supply of impeller key, part code : 4, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 4 22 supply of impeller, part code : 5, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 5 23 supply of neck ring ( suction cover ) , part code : 6, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 6 24 supply of shaft sleeve, part code : 8, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 8 25 supply of pump brg bush, part code : 9, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 9 26 supply of pump shaft, part code : 11, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 11 27 supply of bearing spacer, part code : 13, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 13 28 supply of thrust bearing ( skf or fag 3310 ) , part code : 14, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 14 29 supply of skf bearing washer, part code : 15, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 15 30 supply of bearing cover, part code : 16, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 16 31 supply of coupling key, part code : 17, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 17 32 supply of flexible coupling, part code : 18, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 18 33 supply of gasket ( for casing / delivery pipe ) , part code : 22, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 22 34 supply of`o ring ( for casing ) , part code : 23, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 23 35 supply of clip, part code : 24, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 24 36 supply of gasket ( for casing / concentric reducer ) , part code : 26, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 26 37 supply of adjusting ring, part code : 30, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 30 38 supply of skf lock nut, part code : 32, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 32 39 supply of suction strainer, part code : 2, for emergency lube oil pump, make : wilo mather and platt model no : pnv 24 sr no: 81252046 / 51, as per the npcil drg no: rapp 7&8 / 41332 / 6003 / ga / r2, ref 2...

Rajasthan Rajya Vidhyut Utpadan Nigam Limited - Rajasthan

30814563 requirement of e pac modules and spare parts for auma make actuators at rgtpp, ramgarh oil seal set , thrust bearing with raqce , drive socket limit switch drive assembly , torque switch drive assembly , clutch ring , limit switch , circlip set clutch ring , reduction gearing unit , declutch tripping arm handwheeel retainer , clutch form assembly worm shaft assembly o ring set oil seal set , ball bearing , spur gear , worm gear , stem nut , thrust bearing with race , drive socket , limit switch counter gear , limit switch , etc...