Public Works Department - Rajasthan
39803632 tender for white wash and painting work in v and vi type qtrs under section iii under sub dn gandhinagar i jaipur ( 36 / se city / cd iii / 2216 m r / 07 / 2023 24 ) ...
1
white wash Tenders in Rajasthan
2
Public Works Department - Rajasthan
39803576 tender for white wash and painting work in i and ii type qtrs under sub dn gandhi nagar 1, jaipur ( 45 / se city / cd iii / 2216 m r / 08 / 2023 24 ) ...
3
Public Works Department - Rajasthan
39757700 tender for white wash and painting work iii and ivth type qtrs. under sub dn. gandhi nagar iv, jaipur. 51 / secity / cd iii / 2216 mtc rep / 09 / 2023 24...
4
Public Works Department - Rajasthan
39757590 tender for white wash and painting work in i and ii type qtrs under sub dn. gandhi nagar iv, jaipur. 48 / secity / cd iii / 2216 mtc rep / 08 / 2023 24...
5
Public Works Department - Rajasthan
39732061 white wash and painting work in iii and iv type qtrs under sub dn. gandhi nagar ii, jaipur. 49/secity/cd iii/2216 mtc rep/09/2023 24...
6
Public Works Department - Rajasthan
39732059 white wash and painting work in v and vi type qtrs under sub dn gandhinagar 1, jaipur 34 / secity / cd iii / 2216 mtc rep / 07 / 2023 24...
7
Public Works Department - Rajasthan
39731960 white wash and painting work in v and vi type qtrs under section iii under sub dn gandhinagar 1 , jaipur 35 / secity / cd iii / 2216 mtc rep / 07 / 2023 24...
8
Public Works Department - Rajasthan
39731959 white wash and painting work in iii and iv type qtrs under section iii under sub dn gandhinagar 1 jaipur 50 / secity / cd iii / 2216 mtc rep / 09 / 2023 24...
9
Public Works Department - Rajasthan
39731956 white wash and painting work in minister bunglow under section iii under sub dn gandhinagar 1, jaipur 29/secity/cd iii/2216 mtc rep/05/2023 24...
10
Public Works Department - Rajasthan
39674062 white wash and painting work in minister bunglow under section iii under sub dn gandhinagar 1, jaipur 29 / secity / cd iii / 2216 mtc rep / 05 / 2023 24...
11
Public Works Department - Rajasthan
39674060 white wash and painting work in v and vi type qtrs under section iii under sub dn gandhinagar 1 , jaipur 35 / secity / cd iii / 2216 mtc rep / 07 / 2023 24...
12
Military Engineer Services - Rajasthan
39456813 tender for special repair of offers mess bldg at jalipa mil stn under ge ( a ) barmer ( job no 001 / sr / ( bldg ) / 12c / 23 24 / q3w ) ; 1 s&f for rolled mild steel fe 410 w ( gde e 250 ) quality a in plate girder or single stanchions, built up of one beam of channel section with flange plates, caps, bases, splices, angle brackets, cleats and other connections including with necessary butt or lap welded joint complete all as specified and directed. 2 s&f for rolled mild steel fe 410 w ( gde e 250 ) quality a in compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. including with necessary butt or lap welded joint complete all as specified and directed. 3 s&f for rolled mild steel fe 410 w ( gde e 250 ) quality a in plates ( plain or chequered ) channels. square cut or notched ( ordinary and counter sunk ) forming holes, with riveted, bolted or welded attachment including with necessary butt or lap welded joint complete all as specified and directed. 4 s&f for mild steel screw bolts ( machine made ) of 16 to 24 mm dia of neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, but length of bolt exc 22.5cm and n exc 30cm long embedded in concrete complete all as specified and directed. 5 m&l for steel work in tubular trusses, bracings including special shaped washer etc. complete using erw or induction butt welded tubes conforming to is 1161 1979 grade st. 240 complete all as specified and directed by engineer in charge. 6 m&l for preparation of new or previously untreated steel or iron surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paintover a coat of red oxide primer complete all as specified and as directed. 7 m&l for plain cement concrete 1:4:8 ( type d 2 ) using 40 mm graded crushed stone aggregate in foundations , filling and mass concreate complete all as specified and directed. 8 excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard / dense soil complete all as specified and directed. 9 excavating in trenches, n exc 1.5 m wide and exc 1.5 m in deep but n exc 3.00 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in hard / dense soil complete all as specified and directed. 10 excavation over area n exc. 1.5 m deep and getting out in hard / dense soil complete all as specified and directed. 11 removing excavated material exc. 1.50 km but n exc.5 km complete all as specified and directed. 12 returning filling in including spreading levelling watering and well ramming in layers n.exc 25 cm in soil. 13 formwork to sides rough finished surfaces of concrete of pillars, posts, struts, piers, columns, and stanchions ( leak proof ) complete all as specified and directed by engineer in charge. 14 formwork to flat rough finished surfaces of soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) ( leak proof ) complete all as specified and directed. 15 formwork to rough finished surfaces edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. 16 s&f for mild steel tmt bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 17 s&f for mild steel tmt bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 18 s&f for mild steel tmt bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed. 19 m&l for chipping of 50mm average thickness unsound / weak concrete material from slabs, beams, columns, footings etc. with manual chisel and / or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts complete all as specified and directed. 20 m&l for cleaning & applying rust remover on ( cico clean o rust ) in two coats over rusted reinforcement surface of rcc membersand providing anti corrosive coating with two component epoxy based zinc rich primer / rust passivation inhibitor coat at the rate of 2 3 sq. mtr / ltr not less than 50 microns dft with cico zincilate 500 or equivalent to reinforcement surface as per manufacturer’s instructions including all machinery, tools tackles and clearing of debris. make: cico clean o rust, cico zincilate 500 or equivalent in fosroc / dr fixit / acc / l&t / stp. ( note : entire surface of rcc members shall be measured. ) 21 s&f of new steel or rebars by drilling holes with 10 mm to 25mm dia and 100 to 200mm deep as per is code of 10d formula and filling the holes after inserting of reinforcement dia 8 to 16mm for anchoring at ends / shear connector and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy acrylate fixing and anchoring compound ( having the technical parameters mentioned in material specifications ) using standard sealant applicator gun after drilling holes of required diameter at required locations, for holding / fixing / placing in position the steel mesh reinforcement at desired level / stretching. ( note : steel / reinforcement shall be paid and measured separately ) .make: cico resifix g or equivalent in fosroc lokfix / hilti and master builder ( basf ) 22 m&l for providing micro concrete m 50 ( minimum grade ) with cico microcrete at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine, including all necessary scafolding if required etc all as specified and directed.make: cico microcrete of cico technologies ltd or equivalent in fosroc / stp / basf. 23 m&l for epoxy bonding agent suitable for bonding new to old concrete, bricks and steel components, bricks, tiles etc after the prepration of old concrete / rcc surface by cleaning and removing of dust, dirt, loose particles, laitance etc by wire brushing, scrapping and washing with water complete all as per manufacturers instructions. 24 demolition of brickwork of stone / boulder masonry, build in cement mortar including all for ashlars facings, dressed stonework, precast concrete articles and precast concrete block walling complete all as specified and directed. 25 m&l for pre cast cement concrete block masonry with solid blocks, 1:3:6, type c 1 ( using 20 mm graded aggregate ) exc. 10 cm in width and setting in cement mortar ( 1:6 ) , complete all as specified and directed. 26 taking down cement plaster of any description, any thickness from surfaces of walls / soffits of roof projections & chajjas / ceilings etc. incl raking out joints, hacking for keys, scrubbibg down with water etc complete all as specified and directed. 27 m&l for rendering 15mm thick in cm ( 1:6 ) on fair faces of brick work or concrete surfaces even and fair finish without using extra cement complete all as specified and directed. 28 m&l for 3mm thick wall care putty on wall complete all as specified and directed. 29 m&l for preparing new plastered or unplastered surfaces of walls, and applying two coats of oil emulsion distempering over a coat of interior wall primer complete all as specified and directed. 30 m&l for rendering 15mm thick in cm ( 1:4 ) on fair faces of brick work or concrete surfaces even and fair finish without using extra cement mixed with wpc as per manufacturers instructions complete all as specified and directed. 31 m&l for preparation of new plastered surfaces of walls and applying two coat of cement based paint over a coat of primer complete all as specified and directed. 32 supply only integral liquid water proofing compound complete all as specified & as directed. 33 demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, cills, aprons etc complete all as specified and directed. 34 m&l for virified ceramic tiles ( dark shed ) 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cm ( 1:4 ) complete all as specified and directed. 35 m&l for virified ceramic tiles ( dark shed ) 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick backing coat in cm ( 1:4 ) complete all as specified and directed. 36 m&l for machine cut kota stone slab cills 20 25mm thick over cement screed bed 15mm thick in cm ( 1:4 ) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab inclunding rubbing and polishing complete all as specified and as directed. 37 demolition of cement concrete ( unreinforced ) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 38 m&l for 25mm thick pcc 1:2:4 type b 0 ( using 12.5mm graded stone aggregate ) as in levelling course in floor complete all as specified and directed. 39 m&l for 75 mm thick pcc 1:3:6 type c 1 ( using 20mm graded stone aggregate ) as in plinth protection including making joint at every 3mtr interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and directed. 40 taking down chowkhats or frames ( without taking off shutters from the frame ) exc 1.5 sqm and n. exc 4.00 sqm incl cutting holesand making good reqd shape for hold fast block for new frame complete all as specified and directed. 41 s&f for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. 42 s&f for anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long ( 1 no. ) . hinges type b 21 100mm long ( 2 no. ) suitable handle ( 1 no. ) complete all as specified and as directed. 43 s&f for anodised aluminium door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 nos in each door, hinges, anodised aluminum snap beading screws etc. ccomplete all as specified and as directed. 44 s&f for aluminium ( die cast ) body door closer hydraulically regulated, designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed. 45 m&l for 4.8mm thick sheet glass, ordinary quality and fixed with glazing clips, rubber packing in square in n exc 0.5 sq.m in each pane in each pane complete all as specified and as directed. 46 s&f for stainless steel wire cloth 0.36mm nominal dia of wire andaverage width of aperture 1.40mm and fixed with stainless steel wire stapples complete all as specified and as directed. 47 s&f for 25mm thick pre formed filler for expansion joints including dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed. 48 s&f for heavy duty false work of any height like composite steel section erecting for temporary supports with adjustable arrangement to the structural members like beams, columns, slabs in horozointal or vertical directions etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work and removed after work complete as per the instruction of engineer in charge. note: these supports shall be provided either in the form of props or trestles fabricated using structural steel as per the site requirements complete and all as specified & directed. 49 s&f for ms props of any height, erecting for temporary supports with adjustable arrangement to the structural members like beams, columns, slabs in vertical directions etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work and removed after work complete as per the instruction of engineer in charge. note : these supports shall be provided either in the form of props or trestles fabricated using structural steel as per the site requirements complete and all as specified & directed. 50 s&f for 150mm bore of pvc ( swr ) perforated pipes with 10mm dia perforation holes single socketed in any length with rubber ring joints laid laid in trenches or in floors complete all as specified and as directed. 51 s&f for 150mm bore of pvc ( swr ) pipes single socketed in any length with rubber ring joints laid laid in trenches or in floors complete all as specified and as directed. 52 supply only 20mm nominal size graded coarse aggregate as in trenches around the pvc perforated pipe complete all as specified and as directed. 53 m&l for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed. 54 demolition of cement concrete ( reinforced ) of any description and in any position not otherwise specifically provided for complete all as specified and as directed. 55 m&l for reinforced cement concrete ( design mix ) m 25 ( 20mm graded stone aggregate ) inbeams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by engineer in charge. 56 m&l for reinforced cement concrete ( design mix ) m 25 ( 20mm graded stone aggregate ) incolumns, pillars, piers, posts and struts complete all as specified and directed by engineer in charge. 57 m&l for reinforced cement concrete ( design mix ) m 25 ( 20mm graded stone aggregate ) inslabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, chajjas and in shelves and the like complete all as specified and directed. 58 m&l for reinforced cement concrete ( design mix ) m 25 ( 20mm graded stone aggregate ) infoundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed. 59 m&l for reinforced cement concrete ( design mix ) m 25 ( 20mm graded stone aggregate ) inwalls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed. 60 formwork to sides of flat rough finished surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. 61 formwork to sides of flat rough finished surfaces of concret to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and directed. 62 m&l for plain cement concrete, 1:2:4, type b 1 ( using 20 mm graded crushed stone aggregate ) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. 63 m&l for providing precast cement concrete, 1:2:4, type b 1 ( using 20 mm graded crushed stone aggregate ) in landings, cover slabs ( for manholes etc. ) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and setting in cm ( 1:4 ) with joints to match complete all as specified and directed. 64 m&l for soil stabilization of 150 mm sub grade soil by uniform mixing of cement opc 43 grade / lime / other additive@ 5% cement by weight of soil ( percentage of cement / additives for estimation purposes only type of additive and, percentage required fo blending to be given in mix design ) . item will include pulverization of soil, spreading of additive, blending mix by tractor towed rotovator, addition of water / drying of mix to required moisture content and compaction using suitable vibratory roller to required 95% maximum dry density. provisions of irc sp:89 2010 be referred to for this item 65 m&l for hardcore broken stone / boulder of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled / rammed to a true surface complete all as specified and directed. 66 m&l for complete removal of existing treatment, plastered or unplastered old surfaces of ceiling, including filling of cracks / holes by crack filler, removing unnecessary nails and applying three coats of white wash complete all as specified and directed. 67 m&l for complete removal of existing treatment, plastered or unplastered old surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails applying two coats of oil bound distemper / emulsionover a coat of interior wall primer over 3mm thick wall care putty complete all as specified and directed. 68 m&l for preparing old plastered or unplastered surfaces of walls, including filling of cracks / holes by crack filler, removing unnecessary nails and applying two coats cement based paint complete all as specified and directed. 69 note: ( i ) retrofitting / rehabilitation work shall be executed with / under supervision of specialised agency, charges of specialised agency supervision to be borne by the contractor during the execution of the work as specified and directed. ( ii ) contractor have to get approval of applicator or authorized agency by submitting its authorization letter to this office for approval of accepting officer prior to commencement of work. ( iii ) name of specialised agency : cico resifix g or equivalent in fosroc lokfix and master builder ( basf ) ] ...
13
Military Engineer Services - Rajasthan
39416595 tender for provn of smart meter and server with backup including allied work for jcos / or md accn at lalgarh jattan military station ( 3rd call ) ; phase isupply, installation, testing and commissioning of smart single phase meter with the following specifications:• ac single phase two wire, tamper proof, static meter of class 1.0, 240 v, 50 hz, 10a 60aisi marked conforming to is 16444 2015 and relevant iec standards with inbuilt 865 867 mhz radio frequency communication facility with self healing mesh network with default and on demand display, billing data generation facility, anti tamperfeatures, tamper event detection, microprocessor and led / lcd based circuitry.• meter should support the following data : 15 / 30 min instantaneous data for voltage, current, power factor, power, cumulative energy and frequency, 15 / 30 load survey data for energy, monthly billing survey for cumulative energy and max demand.• meter should have connect / disconnect functionality operatable from prepaid billing software electric supply will be disconnected under followingcondition. ( a ) over current ( 105 % of max current in any phase ) ( b ) load control limit ( programmable ) ( c ) disconnection signal from utility control centre ( d ) the meter shall confirm requirements specified in is 15959. ( e ) all meters should be connected / integrated with their respective data control units and approved softwares / servers. • the meter should support open communication protocol tcp / lp or dlms / cosem to communicate with dcu / hes on rf mesh communication technology. make: secure, xenius, l&t, hpl, panasonic 2 notes: ( a ) the contractor would be responsible from removing the existing meters, noting down the reading and depositing it with the mes store yard of ge sgnr ( age em ) . ( b ) it would be possible to run the meter in both prepaid and postpaid mode ( c ) the meters to carry 05 year guarantee. the contractor shall furnish 05 ( five ) years replacement guarantee for prepaid meters installed under this contract except damage from water and fire. ( d ) whole work shall be executed through origional equipment manufacturer ( oem ) or its authorised repersentative. ( e ) contractor will submit necessary mou on rs 100 stamp paper with oem / authorized rep ( who will provide all these facility mentioned above before commencement of work ) ( f ) the contractor should maintain reserve stock of 3% of total meter installed and replace the faulty meter within one week of complaint given to him.otherwise penal recovery of rs 100 / day / meter will be recovered from the contractor. ( g ) meter should be compliant to is16444. data exchange protocol used should be as per is 15959 ( 2011 ) . ( h ) meter manufacturer should share lls key & hls key of each meter. ( j ) thesmart meter should be rf enabled, the buyer has to insist during purchase ( in specs ) that their mdas can be exchanged with other third party billing systems, and that they will provide support to enable data exchange. another point to be confirmed from meter manufacturing module used inside the meter is a plugin module. 3 notes: ( k ) the cost of internal wiring required for connection of meter and making good disturbed surface & matching with existing surfaces is deemed to included in quated rate. ( l ) while installing power shutdown etc needs to be take in consulation with the user and mes .the contractor should ensure minimum disturbance of powerwhile changing the old metering system to new meters. ( m ) certification of is 16444 may be given by manufactures. ( n ) meter manufactures shall submit is 16444 type test certificates for all metre specification in the tender. ( o ) the meter comunication should work with standrad metal meter panels. 4 supply, installation, testing and commissioning of data concentrator units ( dcu ) / gateway / hes and arrangement of sim card or internet to enable reliable communication with server. the dcu / gateway shall be having ip 65 / ip 54 protection, compatible for remote automatic metering infrastructure ( ami ) solution and capable of communicating with the smart energy meters in the corresponding frequency band and with the data server through lte / gprs / ethernet. it would have capacity to communicate and store data of atleast 200 meters / modules in a radius of approximately 600 800 mtr in mesh formation. the data acquisition ( push / pull ) frequency shall be configurable 15 min, 30 min or 60 minutes. it would have inbuilt battery back up for min 1hour. it would support auto discovery of the meters and self healing mechanism for the breaks in the rf network complete all as specified and directed by engineer in charge.make: secure, l&t, hpl, xenius, panasonic 5 supply and installaton of single phase smart meter as repeater complete all as specified and directed by engineer in charge.make: secure, xenius, l&t, hpl, panasonic 6 supply and installation of ip 54 compliant polycarbonate meter box with transparent cover to view meter display parameter & with transparent / opaque base for single phase smart meter, comply with is 14772:2000 and is 11000:1984. it shall be totally shock proof, safe weather proof, and having internally embedded gasket and sealing provision as required including wiring complete all as specified and directed by engineer in charge.make: hpl, sintex, grasp, hensel / panasonic. 7 supply, engineering, installation, testing and configuration of multi user web based cloud hosted smart metering software system with following features all as specified and directed. ( i ) it would acquire meters data automatically from dcus / gateways and monitor parameters acquired from meters. the meter data management module would be responsible for collecting the data from the concentrator and make the data available to billing system. the meter data management system would capture and provide the following data. ( a ) 15 / 30 min instantaneous data from all the meters for seven parameters – cumulative energy, cumulative apparent energy ( as applicable ) , power, current, voltage, power factor and frequency ( b ) monthly billing survey data for cum energy and max demand ( ii ) postpaid / prepaid billing modulethe billing module would collect the data from the meter data management module, calculate the energy consumption, calculate billing determinant and make energy data / billing data available to admin and end users. the billing module would include functionalities for tariff setup, bill format setup, bill adjustment, occupation billing and vacation billing. it would allow postpaid and prepaid functionality as required. ( iii ) occupation and vacation modulethe system would support occupation / vacation and billing reports.the software would be collecting data from dcu. the software would provide access to staff as well as the occupant for the data. 8 ( iv ) web site: there would be a dedicated website for mes staff to view all the data and information along with customer portal for use of customer. the designated users in mes would have the admin access to the application. the mes staff would also have the access of the key information on an android / ios mobile app ( for admin use ) . website must have only access ofmes authority, not to any third party or web devloper and oem team will visit regularly or on request for any bug fixing as required for smooth runing of website and application software. ( v ) customer portalthe system would include a customer portal for the resident / occupant to log in and view their own energy / billing data. there would be android and ios mobile apps for the user to monitor its own data and balance on regular basis. ( vi ) energy accounting modulethe system would include features of energy accounting. the system would be able to account for total energy block wise, facility wise and would also allow calculations of unaccounted energy in case total energy meter is also available ( vii ) communication modulethe system would provide communication of energy data and bills via print, email and sms methods. 9 ( viii ) meter master datathe system would support meter master data repository. the system would support meter replacement process. ( ix ) excel exportthe system would support export of metering and billing data in excel format. ( x ) customer care module the software would include a customer care module where the user would be log in any complaints. the service provider would monitor the complaints and carry out the necessary activities for the complaints resolution. ( xi ) meter installation module the software would include an app based meter installation module where the meter installation or changes can be captured on the app itself and the readings may be demonstrated to the user if required on the app itself. ( xii ) activities communication the software support communication of the various activities such as occupation, vacation, meter change. personal detail change etc. with the user as well as the department on email.contractor should submitmoufrom oem toprovide the software & hardware update for smart meter / data communicator / website / mobile app / application software. ( xiii ) ( a ) . application software / mobileapp, website and other connected items must be supplied as recommonded by oem ( manufacturar of meter ) irrespective of developers and contractor should submit mou on 100 rupees non judicial stamp paper to provide the availability of software update / hardware spares for five years. 10 ( b ) all softwares / applications must have security provisions to protect privacy data and army area security, ( c ) the software would contain two years defect liability including all operating expenses such as regulator security patch updates, hosting charges, future integration with meters etc. ( d ) personal data of user and electric comsumption data shall be stored on the ministry of electronics and information technology ( meity ) approved cloud server designated specifically for the purpose. cyber security audit shall be carried out by govt empaneled cert in auditor and compliance report shall be submitted to ge. the oem shall submit an affidavit to ge confirming that mes data will not be shared to any third party and shall not be used in any case and the same shall also be confirmed during third party cyber security audit by govt empaneled cert in auditor. ( e ) personal data for user / qtr / accn on standard format as required for software shall be provided by the dept. ( f ) the configuration of smart meter will be through software which will be compatible with all makes of smart meter and complete smart metering system will be audited by cert in empaneled firm and cost of audit is to be borne by contractor. the cert in auditor shall submit preliminary audit report and oem shall take action based on the report and resolve all issues. ( g ) the software provided by the firm is to be user friendly and compatible with future upgradation. ( h ) system should be compatible with all possible payment / recharge mode, be it online or offline mode. ( j ) software for smart meter should also include prepayment mode recovery of licence fee, higher charge of furniture, water charges etc as directed to contractor by mes. 11 ( k ) smart meter and software / mobile application will be in compliance with service hq cyber security norms. ( l ) one payment gateway would be installed and connected to the sbi public bank account provided by the ge. this payment gateway should have both payment options of online payment and offline payments.make :hpl, oracle, secure, xenius, innologix, panasonicnotes: ( 1 ) oem shall arrange 3 days training to mes staff for understanding complete system incl software and the cost of the same is deemed to be included in quoted rate. ( 2 ) the quoted rate would include provision of high speed 1 gbps broadband seperate connection for system ( 3 ) the software should support future integration with any is 16444 based meter provided the meter integration details and / or headend integration details are made available. ( 4 ) all charges for taking cloud service and cost of cyber security audit is deemed to be included in the quoted rate. ( 5 ) the configuration and necessary arrangement for payment gateway and e mro facility as reqd shall be deemed to be included in the quoted rate. ( 6 ) the above system is considered as complete system delivery for smart metering system and any additional hardware / software reqd based on proposed system architecture by oem is deemed to be included in quoted rate. no claim shall be entertained in this regard. ( 7 ) the software shall be demonstrated compartible with at lease three makes of the smart meter. 12 supply and installation of ups for the server with the specification10 kva, 230v suitable for india harsh environment or equivalent complete with joints to match complete all as specified and directed by engineer in chargemake: aps, emerson, luminous 13 excavation in trenches, not exc. 1.50 mtr wide and not exc 1.50 mtr in depth and getting out in soft / loose soil for foundations complete all as specified and directed by engineer in charge. 14 m & l for pcc ( 1:4:8 ) type d 2 ( using 40mmgraded crushed stone aggregate ) as in foundation filling and mass concrete complete all as specified and directed by engineer in charge. 15 m&l for formwork to chajjas, lintel beam, troughts and similar items including edges rough finish surface of concrete flat complete all as specified and directed by engineer in charge. 16 m&l for formwork to soffits of suspended slabs such as roof slabs, floor slabs thickness n. exc. 200 mm ( horizontal or sloping ) in rough finish complete all as specified and directed by engineer in charge. 17 m&l for fromwork to edges of concrete flats, treads breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20cm wide and sides of rcc / pcc bands in walls, orizontal or sloping and similar work exc 10 cm but n.exc 20 cm wide, roughed finished surfaces of concrete complete all as specified and directed by engineer in charge. 18 m & l for mild steel tmt bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire ( annealed ) not less than 0.90mm dia complete all as specified and directed by engineer in charge. 19 all as per item no 13 here in before but 5mm dia and over upto and including 10mm dia as in stirrups, spaces & binderscomplete all as specified and directed by engineer in charge. 20 m&l for rcc m 25 ( design mix ) using 20 mm graded stone aggregate as inbeams, chajjas, cantilevers, bressummers, lintel beam & ovr 1.5m span complete all as specified and directed by engineer in charge.note: reinforcement shall be measured and paid separately. 21 m&l for rcc m 25 ( design mix ) using 20 mm graded stone aggregate as in slab suppored on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likecomplete all as specified and directed by engineer in charge.note: reinforcement shall be measured and paid separately. 22 m&l for brick work withfly ash bricks bricks straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar ( 1:6 ) complete all as specified and directed by engineer in charge. 23 m&l for 40mm thick damp proof course in cement concrete 1:2:4, type b 0, 12.5 mm graded stone aggregate with wpc to horizontal or vertical surfaces including necessary formwork complete all as specfied and directed by engr in charge. note : approved water proofing compound shall be measured and paid separately as supply only. 24 returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm complete all as specified and directed by engineer in charge. 25 spreading and levelling in layers n.exc 25cm thick and well ramming including watering as required under floors complete all as specfied and directed by engr in charge. note. earth required for filling shall be used obtained from earth work. 26 removal of surplus soil obtained from excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed by engineer in charge. . 27 m&l for hard core of gauge n.exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface brocken stone or boulders ( 15cm compacted thickness ) complete all as specified and directed by engineer in charge. 28 m&l for 75 mm thick pcc ( 1:3:6 ) type c 1 using 20 mm graded crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10 mm wide, 30 mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as specified and directed by engineer in charge. 29 m & l for 75mm thick pcc ( 1:4:8 ) type d 2 ( using 40mm graded crushed stone aggregate ) as in sub base below floors complete all as specified and directed by engineer in charge. 30 m & l for 25mm thick pcc ( 1:2:4 ) , type b 0, using 12.5mm graded crushed stone aggregate as in floor complete all as specified and directed by engineer in charge. 31 m&l for machine cut kota stone slab flooring, 20 25mm thickover and including 20 mm thick screed bed in cement mortar ( 1:6 ) base laidand jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete all as specified and directed by engineer in charge. 32 m & l for 20 25 mm thick machine cut kota stone slabs as in vertical surfces such as risers of steps laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing and moulding edgesover and including 10mm thick rendering in cm ( 1:4 ) complete all as specified and directed by engineer in charge. 33 m&l for 10mm thick rendering in cm ( 1:6 ) to brick / concrete surfaces finishedeven & smooth without using extra cement complete all as specified and directed by engineer in charge. 34 m&l for rendering 15 mm thick in cement mortar ( 1:4 ) onfair face of brick walls, finished even & smooth without using extra cement, complete all as specified and directed by engineer in charge. note: wpc shall be measured and paid separately as supply only. 35 m&l for rendering 5 mm thick in cement mortar ( 1:3 ) on concrete surfaces as in ceiling, finished even & smooth without using extra cementcomplete all as specified and directed by engineer in charge. 36 supply only liquid water proofing compound complete all as specified and as directed by the engineer in charge. 37 m&l for preparation and applying three coats of white wash on newly plastered surface of ceiling complete all as specified and directed by engineer in charge. 38 m&l for preparation andapplying two coats of oil bound distember over a coat of primer on newly plastered surface of wall paint over3mm thick thick wall care putty complete all as specified and directed by engineer in charge. 39 m&l forpreparation ofnew plasteredandtreating with two coats ofweather proof exterior emulsion paint ( apex ultima or equivalent ) over a coat of primer over 3 mm thick wall care puttycomplete all as specified and directed by engineer in charge. 40 material and labour for water proofing treatment over 10mm thick screed bed in cm 1:3mixing of wpc in mortar inrcc slab by applying one coat of bituminous primer @ 0.25 kg / sqm and providing 3mm thick app modified water proofing membrane weighting not less than 3.5 kg / sqm, reinforced with non woven polyster reinforcement mat weighing not less than 160 gm / sqm, polyster core having softening point not less than 150 degree c, longitudinal tensile strength not less than 650 n / 5cm, tearing strength of 180n / 5cm including two coat of solar reflective aluminium paint @ 0.15kg / sqm including cleaning the newly plastered surfaces of concrete / existing plastered vertical surfaces with wire brushes free from dust etc complete all as specified and directed by engineer in charge. 41 m & l for cement concrete tiles 25cm x 25cm x 22mm thick, macine pressed; over cement screed base laid over cement screed base laid over and including15 mm thick screed bed incement mortar 1:6, set and jointed with grey cement slurry mixed with pigment and no pigmentin floors / roof, and cut and polished complete all as specified and directed by engineer in charge. 42 s & f for aluminium anodised ( powder coated ) three track sliding window frame with shutters ( two glazed and one gauged shutter ) including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete andglazing with 5 mm thick tinted glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc with the following section of frame and shutter ( a ) sections for frame. ( i ) top and verticals 92 x 29.50 x 1.30 mm thick ( ii ) bottom 92 x 29.50 x 1.20 mm thick. ( b ) sections for shutter ( i ) a section 39 x 20 x 1.50 mm thick ( ii ) interlock section 39 x 20 x 1.50 mm thick ( iii ) h section 41 x 20 x 1.10 mm thick make: jindal or equivalent sections of hindalco. 43 s & f powder coatedaluminium door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed by engineer in charge. 44 m & l for door closer hydraulically regulated of aluminium cast type , designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed other parts made of mild steel heavy duty and fixed complete all as specified and directed by engineer in charge. 45 s & f 4 lever brass body mortice lock, vertical type, size 100 mm complete all as specified and directed by engineer in charge. 46 m&l for 4.0 mm thick figured glass, ordinary quality and glazing with aluminium snap beading of any size in each panescomplete all as specified and directed by engineer in charge. 47 surface excavation n.exc. ( not exceeding ) 30 cm deep and averaging 15cm deep and getting out in soft / loose soil complete all as specified and directed by engineer in charge. 48 m&l for 75 mm thick pcc ( 1:3:6 ) type c2 using 40mm graded stone aggregate as in sub base below floors complete all as specified and directed by engineer in charge. 49 m&l for precast cement concrete ( 1:2:4 ) type b1 using 20mm graded stone aggregate as in kerb stones size 300mm x 300mm x 100mm with plain fair faces, including chamfers, weathering, throating etc setting in cm ( 1:4 ) complete all as specified and directed by engineer in charge. 50 m&l for 60mm thick m 35 grade machine pressed precast concrete interlocking paver block glossy with grey cementand pigment, any shape and size confirming to is 15658 2006 over and including 25mm thick sand cushion complete all as specified and directed by engineer in charge. 51 supply, installation and setup of application server and backup server dell power edge tower server t550. the sever would be suitable for 5000 meters. the below specifications are indicative. the servers may be hosted at the locations provided by the department.• 3.5 chassis with up to 8 hard drives ( sas / sata ) , 1 cpu • cpuintel® xeon® silver 4314 2.4g, 16c / 32t, 10.4gt / s, 24m cache, turbo, ht ( 135w ) ddr4 2666 • memory 16gb rdimm, 3200mt / s, dual rank• hard drive 800gb ssd sas ise mixed use 12gbps 512 2.5in hp ag drive, 3.5in hyb carr, 3 dwpd • standard heat sink for less = 150w• dual, hot plug, non redundant power supply ( 2+0 ) , 600w, mixed mode make: dell, hp, ibmnote: ( 1 ) the server cost would include two year charges for high speed 1 gbps broadband connectionfor one locations. ( 2 ) the server cost would include suitable data switch, firewall, monitor. 52 phase iiamc of smart metering system excluding warranty of all hardware and software ( covered in defect liability period ) and other operating costs after completion of work which includes the following: ( a ) monthly sim charges for all dcus / gateways. the contractor would ensure supply of appropriate sims / modules to ensure necessary signal availability. the contractor would change the sim or sim provider as required. in case of network issues, the contractor would change sim or liase with the service provider for necessary resolution. ( b ) recurring sms charges. the sms would be issued for the payments alerts, low balance alerts and disconnection / connection alerts. ( c ) software and security patch updates which includes necessary upgradations in the software as required. ( d ) yearly changes in the government tariff structure, if any and the same to be updated in software. ( e ) remote server admin support ensuring adequate database back up, upgradations in the operating system, anti virus updates, database upgrade etc. ( f ) reports development the additional reports as needed for the success of the project would be developed ( g ) the communication network monitoring and support . trouble shooting and necessary actions to run the system, software bug fixing as and when requiredand managing meter recharge problems. ( h ) rectifying any problem that may occur in the hardware / software system and coordinating for smooth functioning and deploying all measures for corrective actions as and when required. 53 ( j ) providing training to mes personnel as and when required & directed. ( k ) generation and maintenance ofe cash payment details and updating the same to mes designated officer and reconcilliation of account on monthly basis. ( l ) providing any other associated technical support. ( m ) payment of cyber security audit charges by cert in auditor, which is be carried out annually. ( n ) payment of high speed 1 gbps broadband charges. ( o ) payment of cloud charges to oem for smooth functioning and data backup. 54 ( p ) contractor will employ min 01no trained / skilled personel at ge lgj in shift from 9:00 am to 5:00 pm ( except on sunday and holiday ) after completion of work for a period of two year, the duties shall include: ( i ) managing meter recharge problems. ( ii ) rectifying any problem that may occur in the hardware as well as software system and coordinating for smooth functioning of the same. ( iii ) deploying all measures for corrective actions as and when required. ( iv ) acting as a link between respective ge / resident and the parent company providing the metering system. ( v ) providing training to mes personnel as and when required & directed. ( vi ) generation and maintenance ofe cash payment details and updating the same to mes designated officer. ( vii ) providing any other associated technical support.notes: ( a ) phase ii shall be operative & commence after declaring all meters commissioned and post completion of work. ( b ) absence of responsible persononel for system during phase ii ( amc ) of work, rs. 500 / day penalty will be recovered from contractor fron next due rar. ( c ) non rectification / non observance / delay in attending breakdown of system beyond 24 hours ( smart meter, dcu, software ) , rs.1000 / day penalty will be recovered from contractor. 55 comprehensive amc of complete system including operating costs after completion of 2 years defect liability period which includes the following: ( a ) monthly sim charges for all dcus / gateways. the contractor would ensure supply of appropriate sims / modules to ensure necessary signal availability. the contractor would change the sim or sim provider as required. in case of network issues, the contractor would change sim or liase with the service provider for necessary resolution, recurring sms charges. the sms would be issued for the payments alerts, low balance alerts and disconnection / connection alerts. ( b ) hardware amc. this would include necessary replacement of any hardware incl dcu incase of any defect. ( c ) software amc. this would include necessary upgradations in the software such as support to the chrome browser changes, android version changes, security patch updates, ios version changes. these changes happen on frequent basis and the software would support all the changes. ( d ) changes in the government tariff structure. the government tariff structure changes may require software upgrade. the same would be included in the amc scope of work. ( e ) remote server admin support ensuring adequate database back up, upgradations in the operating system, anti virus updates, database upgrade etc. ( f ) reports development the additional reports as needed for the success of the project would be developed ( g ) software installation on any alternate / backup server if required 56 ( h ) the communication network monitoring and support , trouble shooting and necessary actions to run the system, software bug fixing as and when requiredand managing meter recharge problems. ( j ) rectifying any problem that may occur in the hardware / software system and coordinating for smooth functioning and deploying all measures for corrective actions as and when required. ( k ) providing training to mes personnel as and when required & directed. ( l ) generation and maintenance ofe cash payment details and updating the same to mes designated officer and reconcilliation of account on monthly basis. ( m ) providing any other associated technical support. ( n ) payment of cyber security audit charges by cert in auditor, which is be carried out annually. ( o ) payment of high speed 1 gbps broadband charges. ( p ) payment of cloud charges to oem for smooth functioning and data backup.notes: ( a ) non rectification / non observance / delay in attending breakdown of system beyond 24 hours ( smart meter, dcu, software ) , rs.1000 / day penalty will be recovered from contractor....
14
Department Of Defence - Rajasthan
39282826 bids are invited for putty glass , wall putty , geru mitti , mitti pili , paint white make berger asian nerolac or equivalent in pack of 4ltrs , paint black make berger asian nerolac or equivalent in pack of 4ltrs , blue robin neel , lime unslacked , thinner pack of 5 ltr , varnish pack of 1 ltr , wood primer pack of 1 ltr , red oxide make berger asian nerolac or equivalent in pack of 4 ltrs , sand paper no 100 , snowcem pale cream , kuchi for white wash , fevicol in 1 kg pack , fevicol ddl in 1 kg pack , fevicol sr , fevicol sh , painting brush nylon size 1 inch , painting brush nylon size 2 inch , painting brush nylon size 3 inch , painting brush nylon size 4 inch , painting brush nylon size 5 inch , painting brush nylon size 6 inch , distemper brush of size 100mm , white washing brush of size 5 6 , roller brush for painting of size 9 inch , distemper brush of size 5 inch 6 inch , dendrite wood shine pack of 1 ltrs , distamper white make asian nerolac berger or equivalent in pack of 04 ltrs , distamper pale cream make asian berger nerolac or equivalent in pack of 04 ltrs , distemper colour pale cream make berger asian nerolac or equivalent in pack of 4 ltrs , distemper colour white make berger asian nerolac or equivalent in pack of 4 ltrs , distemper colour pink make berger asian nerolac or equivalent in pack of 4 ltrs , paint synthetic enameled po red make berger asian nerolac or equivalent in pack of 4 ltrs , paint golden yellow make berger asian nerolac or equivalent in pack of 4 ltrs , paint phiroze blue sky blue make berger asian nerolac or equivalent in pack of 4 ltrs , emulsion paint pale cream exteriormake berger asian nerolac or equivalent in pack of 4 ltrs , stainer different colours make berger asian nerolac or equivalent as per buyer requirement , cement primer , paint olive green make berger asian nerolac or equivalent in pack of 4 ltrs , distemper pink oil bound make berger asian nerolac or equivalent , paint synthetic enamel black make berger asian nerolac or equivalent in pack of 4 ltrs , paint synthetic enammeled white make berger asian nerolac...
15
Public Works Department - Rajasthan
39242496 white wash work in sahyog appartment vidhyadhar nagar jaipur ( 33 / secity / cd iii / 2216 mtc rep / 07 / 2023 24 ) ...
16
Military Engineer Services - Rajasthan
39191248 tender for special repair to bldg no t 04 and p 25 at lgj mil station; 1 dismantling of brick tiles or terracing tiles, single layer on roofs complete all as specified and as directed by engineer in charge. 2 demolition mud in roofs, any thickness, including plastering and leeping complete all as specified and directed. 3 demolition of cement concrete of any description ( unreinforcement concrete ) and in any position not otherwise specifically provided for complete all as specified and directed. 4 demolition of brick work or stone / boulder masonry, built in cement mortar including allquoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by engineer in charge. 5 demolition of cement concrete of any description ( reinforcement cut as required to facilitate ) demolitionand in any position not otherwise specifically provided for complete all as specified and directed. 6 formwork to chajjas, troughs and similar items including edges , for rough surface of concrete, complete all as specified and directed by engineer in charge 7 m&l for reinforced cement concrete 1:1.5:3 type a 1 using 20mm graded stone aggregrate in chajjas; complete all as specified and directed by engr in charge.note : reinforcement shall be measured and paid seperately. 8 m&l for 40 mm thick cement concrete type b0, 1:2:4 ( 12.5 mm graded stone aggregate ) as in roof padding and laid in slope 1:30 complete all as specified. 9 m&l applying evenly a tack coat of industrial bitumen 85 / 25 at the rate of 1.2 kg per sqm as in roof including cleaning surfaces all as specified and directed 10 m & l app based membrance minimum weighing 3 kg per sqm and minimum 3mm thick reinforced with polyster non woven fabric ( wt not less than 150 gms / sqm ) laid on primed surface by torced application with app membrane over10mm thick screed bed in cm 1:3mixing of wpc in mortarcomplete all as specified & directed. 11 m & l for cement concrete tiles 25cm x 25cm x 22mm thick, m a c h i n e pressed; over cement screed base laid over cement screed base laid over and including15 mm thick screed bed incement mortar 1:6, set and jointed with grey cement slurry mixed with pigment and no pigmentin floors / roof, and cut and polished complete all as specified and directed. 12 m&l pcc 1:2:4 type b 1, using ( 20mm graded stone aggregate ) as in roof kerbs or mud stops, rounded or chamfered on edges including necessary form work etc complete all as specified & directed 13 m&l forbrick work with fly ash bricks straight or curved on plan exc. 6 metre mean radius built in cement mortar ( 1:6 ) all as specified & directed. 14 m&l for old size brick work with fly ash bricks straight or curved any radius half brick thick walls, built in cement mortar ( 1:4 ) all as specified & directed. 15 s&f for framed work such as grills, gratings etc., with ends of bars shouldered and / or riveted, or forget into spikes, framed guard bars; barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to fe 290 0 or grade e 165 complete all as specified and as directed 16 taking down wooden chowkhats or frames with shutters ( without taking off shutters from the frames ) area exceeding 1.50 sqm but not exceeding 4.00 sqm each and removing from site all as specified & directed 17 taking down existing shutter and refixing in same opening shutters of any description exc 1.0 sqm but not exc 2.0 sqm each all as specified and directed. ( note: refixing includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc. ) 18 taking down wooden chowkhats or frames n.exc 1.5 sq. m each with shutters ( without taking off shutters from the frame ) complete all as specified and directed by engr in charge. 19 taking down shutters of any description exc 1.00 sqm but not 2.00 sqm each including removing to store complete all as specified and directed. 20 supply & fixing 35mm thick 2nd class hard wood factory made plain framed panelled shutters ( two panels ) with lock rail and panel inserts of comercial veneered particle board with commercial veneering on both faces.the size of rails and styles as per is 1003 ( part i ) , kiln seasoned and chemically pressure treated all as specified & directed 21 supply and fixing of fibre glass reinforced plastic ( frp ) door frame of required built in colour in three legged of cross section 90mm x 45mm having single ribate of 32mm x 15mm to recieve shutter of 30mm thick includinglaminated door frame moulded with fire retardant grade unsaturated polyster resin and chopped strand mat ( csm ) also door frame laminated shall be 2mm thick and shall be filled with suitable wooden block of 2nd class hard wood in all three legs frame shall be covered with fibreglass from all sides ms stay flat iron 25mm x 3mm shall be provided at the bottom to steady the frame complete all as specifiedand as directed by engineer in charge. 22 supply and fixing of 30 mm thick glass fibre reinforced plastic ( frp ) paneled door shutter conferming to is:14856 2000 of required colour andmade with fire retardant grade unsaturated polyster resin, moulded to 3mm thick frp laminated for forming hollow rails and style with suitable second class hardwood timber block inside at required places for fixing of fittings, cast molithically with 5mm thick frp laminated for panels including fixing to frames, complete all as specified and as directed by engineer in charge. 23 dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed 24 m&l for rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates and conforming to fe 410 w ( gde e 250 ) quality a complete all as specified and directed 25 s & fframed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting of other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel handing door fitttings ( exclusive or steel sheeting or other covering, running rails and guides ) and hanging also fastening and fixing confirming to fe 410 w ( gde e 250 ) complete all as specified and directed by engr in charge. 26 s&f 150mm long aluminium alloy handles, fabricated type, anodised complete all as specified & directed by engr in charge. 27 s&f aluminium anodised barrel tower bolt of extruded section 200mm longall as specified & directed by engr in charge. 28 s&ffor 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring all as directed. 29 s&f stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture1.40 mm and fixed with stainless steel wire staplesall as directed. 30 s&f for powder coated aluminium frame / shutter for doors, windows, ventilators and aluminium partition with one or more rebates including jointing cleats glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete with locking arrangements for fixing with powder coating on aluminium sections, minimum thickness of poweder coating shall be 50 micron as per the specification. the top and bottom horizontal members and vertical members adjacent to wall shall be fixed with floor, ceiling, walls and cills where required and fixed with the help of rawl plugs and screws or with fixing clips or with expansion hold plate fastners. aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically whereever required complete in all respect all as specified & directed by engr in charge. make of al section : jindal / hindalco / nalco 31 s & f powder coatedaluminium door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 03 nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed note : minmum thickness of powder coating should be 50 microns. 32 s&f for powder coated anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing exc 0.55 kg / m ( 1.50 to1.80mm th ) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings suchas peg stays 150 mm long ( 01 no ) hinges type b 21 100 mm long ( 2 nos ) suitable handle ( 01 no ) in each window shutter and necessary accessary as required complete all as specified and directed by engineer in charge ( note : glass will measured and paid separately ) 33 s & f for aluminium anodised ( powder coated ) three track sliding window frame with shutters ( two glazed and one gauged shutter ) including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete andglazing with 5 mm thick tinted glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc with the following section of frame and shutter ( a ) sections for frame ( i ) top and verticals 92 x 29.50 x 1.30 mm thick ( ii ) bottom 92 x 29.50 x 1.20 mm thick. ( b ) sections for shutter ( i ) a section 39 x 20 x 1.50 mm thick ( ii ) interlock section 39 x 20 x 1.50 mm thick ( iii ) h section 41 x 20 x 1.10 mm thick make: jindal or equivalent sections of hindalco / nalco. 34 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) and rubbish off the premises all as specified and as directed. 35 m&l for joint free non skid ceramic coloured tiles 7 to 8 mm thick ( square / rectengular ) area of each tile exc 0.11 sqm but not exc 0.18 sqm in floor over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match the floorall as specified and directed. 36 m&l glazed ceramic coloured tiles 450 x 300 x 7 mm thick joint less tiles as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick rendering in cement mortar ( 1:4 ) including necessary cutting as per site requirement complete all as specified and directed 37 s & f virified ceramic tiles light colour 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick rendering in cm 1:6 complete all as specified and directed 38 s & f virified ceramic tiles light colour 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm but not exceeding 1.25 sqm, as in dado / skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in cm 1:4 complete all as specified and directed 39 dismantling stone slabs and tiles of any description or thickness in floors, aprons etc and laided, bedded and pointed in any mortar complete all as specified and directed. 40 m&l for 20 mm thick granite ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite over 20 mm thick screed bed in cm 1:6 completeall as specified and directed. 41 rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified and directed 42 taking down cement plaster on brick / terrazoo on brick / stone walls including raking out joints, hacking for key, scrubbing down with waterall as directed 43 m&l for rendering 15mm thick on brickwork or concrete surfaces in cement mortar 1:6 on wall and finished fair even and smooth without using extra cemnt all as specified and directed. 44 m&l for rendering 15mm thick on brickwork or concrete surfaces in cement mortar 1:4 on wall and finished fair even and smooth without using extra cemnt all as specified and directed. 45 m & l for rendering 10 mm thick on concrete surfaces in cm 1:4finished even and smooth on ceilingwithout using extra cementall as specified and directed by engr in charge. 46 m&l for preparation of newceiling surface and applyingtwo coats of acrylic distemperover a coat of primer complete all as specified and directed by engr in charge. 47 m&l for complete removal of existing treatment in old ceiling surfaces and appying two coat of acrylicdistemper ( any colour / tint ) on ceiling surface complete all as specified and directed by engr in charge. 48 m&l for applying two coats of acrylic distemper over a coat of primer over 3 mm thick wall care puttyon newly plastered surfacesof wallsincluding preparation of surfaces complete all as specified and directed by engr in charge. 49 m&l for complete removal of existing treatment from walls andapplying two coats of acrylic distemper over 3 mm thick wall care putty of wallsincluding preparation of surfaces complete all as specified and directed by engr in charge. 50 m&l preparing newly plastered of wall and applying three coats of white wash on wall complete all as specified & directed by engr in charge 51 m&l for preparation of new plastered surface of walls and applying two coats of cement base paint all as specified & directed by engr in charge. 52 m&l for applying two coats of weather proof exterior emulsion paint ( apex ultima or equivalent ) over a coat of alkali resistant primer over 3mm thick wall care putty on newly plastered surfacesof walls including preparation of surfaces complete all as specified and directed by engr in charge. 53 m&l for preparation of old plastered wall surface and treating with two coats of weather proof exterior emulsion paint ( apex ultima or equivalent ) over a coat of alkali resistant primer over 3mm thick wall care putty complete all as specified and directed by engineer in charge. 54 m & l for painting new / untreated steel and iron surfaces of any discription, over 10 cm width or girth, withtwo coats of synthetic enamel paint over coat of red oxide primer ordinary tint includingpreparation of new surfaces all as spefified and directed 55 m & l for painting oldsteel and iron surfaces of any discription, over 10 cm width or girth, withtwo coats of synthetic enamel paint ordinary tint includingpreparation of old surfaces all as spefified and directed 56 m&l preparation of new or previously untreated wooden based surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer all as specified. 57 s & f 4 mm thickfigured glass, pin head oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed. 58 taking down pvc soil, waste& rain water pipe 100 / 75 mm dia including fittings fixed to walls, laid in floor etccomplete all as specified and directed by engr in charge. 59 s&f 110 mm dia bore pvc ( swr ) pipe, single socketed in any length with rubber ring joints fixed with clamps to wallsall as directed. 60 s&f 75 mm dia bore pvc swr pipe, single socketed in any length with rubber ring joints fixed with clamps to walls and including bend as per side requirement, taking down existing pipe all as directed. 61 s & f pvc ( swr ) bend 110 mm bore all as specified & directed by engr in charge 62 s & f pvc ( swr ) bend 75 mm bore with access door and radiusall as specified & directed by engr in charge 63 s & f 110 mm bore pvc ( swr ) branch piece double ( single y ) equal or unequal all as directed 64 s & f in repair 100 bore of spun cast, cast iron soil, waste and vent pipes in any length with or without ears, with cement joint and laid in trenches or in floors cast ironcomplete all as specified and directed. 65 s & f in repair 75 mm bore of spun cast, cast iron soil, waste and vent pipes in any length with or without ears, with cement joint and laid in trenches or in floors cast ironcomplete all as specified and directed. 66 s & f in repair cast iron 100 mm bore branch pieces, single ( equal or unequal ) , ordinary or inverted ( spigot or socket type ) or with parallel branchescomplete all as specified and directed. 67 s & f in repair cast iron 75 mm bore branch pieces, single ( equal or unequal ) , ordinary or inverted ( spigot or socket type ) or with parallel branchescomplete all as specified and directed. 68 s & f in repair cast iron 100 mm bore bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) complete all as specified and directed. 69 s & f in repair cast iron 75 mm bore bends ( any radius ) , diminishing pieces or tapers ( larger bore measured ) complete all as specified and directed. 70 m & l in repairscast iron floor trap dia of out let 75 mm, with grating including jointing to waste pipe fixed in cement concrete type b 1, ( 1:2:4 ) complete all as specified and directed by engineer in charge. 71 m & l pvc ( swr ) gully trap 125 / 110 mm, setting and jointing with solvent cementcomplete all as specified and directed by engineer in charge. 72 taking down 15 mm dia steel gi tubing including all connected fittings of any dia and in any positionall as directed. 73 all as per item no 72 above but 20 mm dia pipe 74 all as per item no 72 above but 25 mm dia pipe 75 s&f 15 mm diagalvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etcfixed to walls / ceiling complete all as directed. 76 all as per item no 75 above but fixing only 77 all as per item no75above but 20 mm dia pipe 78 all as per item no 75 above but 25 mm dia pipe 79 s&f in repair bib tap 15mm bore cast copper alloy chromium plated long body fancy type with capston head and cup screwed down, hand operated, screwed for iron pipe or for brass ferrule all as specified. 80 s&f in repair cp brass stop valve / angle valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy typefixed complete all as specified and directed by engr in charge. 81 s&f in repair cp brass stop valve / angle valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup ( concealed type ) fixed complete all as specified and directed by engr in charge. 82 s & f in repair brass chromium plated liquid soap dispenser complete all as specified and as directed by engineer in charge. 83 s&f in repair gun metal globe or gate valve 25 mm bore with iron wheel head, screwed both ends for iron pipe and fixed all as specified and directed by engineer in charge. 84 s&f in repair gun metal globe or gate valve of 20 mm bore with iron wheel head, screwed both ends for iron pipe and fixedall as specified and as approved by ge / engineer in charge. 85 m & l for 19 mm thick plywood fixed in repair, grade bwr, type bb, with decorative face veneers on both faces; handle and fixed with screws to timber frame work complete all as specified and directed 86 s & f continuous ( piano ) hinges mild steel bright finsh or electro galvanised, width of flap when open 30mm complete all as specified and directed by engr in charge. 87 s&f drapery stainless steel rods, standarad quality, not less than 25 / 28 mm dia with heads, brackets and boths ends stainless caps , etc. all as specified and direced. 88 s&f in repairvitreous china squatting pan orissa pattern size 580 x 440 mm white with integral foot rests ( excl flushing cistern ) but including ci p trap set in cement concrete fixed all as specified. 89 s & f in repair cabinet mirror of size 400mm x 500 mm fixed with wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by engineer in charge 90 s&f in repair looking mirror of selected quality on size600 mm x 450 mm withbevelled edge mounted 6 mm thick commercial plywood and aluminium channel of required size fixed to pvc plugs with chromium plated brass screws and cup washers all as directed. 91 s&fin repairtubular towel rail stainless steel20mm dia d type 60cm long between flanges complete all as spd & dir by eic. 92 s & f in repair corner glass shelf 200 mm with abs brackets complete all as specified and directed by engineer in charge 93 s&f in repair chromium plated fancy type soap dish complete all as specified and directed 94 s&f in repair vitreous china wash down water closet pan ( pedestral pattern ) , white ( excluding fixing bolts , flushing cistern and flush pipe ) , including connection to drain ( or outgoing pipe ) and to flushing pipe, antisyphonage pipe, etccomplete. 95 s&f in repair vitreous china wash hand basin coloured counter flat back of size 550x400mm, long screwed shank fly nut flangeend including cutting for and pinning in ends of brackets in 1:3 cm including 32mm dia chromium plated waste coupling / trap all as specified . 96 s&f in repair vitreous china wash hand basin coloured counter top ( bowl type / oval shape ) of size 560x450mm, long screwed shank fly nut flangeend including cutting for and pinning in ends of brackets in 1:3 cm including 32mm dia chromium plated waste coupling / trap all as specified . 97 s&f in repairs grating doom cp 100 mm diawith waste hole complete all as specified and directed 98 s&f in repair stainless steel trap with grating round or square 150mm size ( minimum weight 100gms ) complete all as specified and as directed by engineer in charge. 99 s & f in repairs 32 mm pvc waste down pipe suitable for whb and urinal complete all as specified and directed by engineer in charge 100 supply and fixing in repair hot and cold whb mixer cast copper alloy chromium plated quarter turn screwed down for pipe of15mm bore complete all as specified and directed by engineer in charge 101 s & f in repairwall mixer with l bend 115 mm long full system brass ( cast copper alloy ) chromium plated, mixer for mixing hot & cold water, screwed down for iron pipe 15 mm borecomplete all as specified and as directed by engineer in charge 102 s&f in repair health faucet with cp flexible cord fixed on wall complete all as specified and directed by engneer in charge 103 s&f in repairs pvc valve less, syphonic action type flushing cistern, 10 ltrs capacitylow level, white, with inlet ball valve, float, handle, and connection to pipesand flush pipe of polyethylene of low or high density or pvc, 32mm dia, for low level cistern all as directed. 104 s&f in repair cp towel ring of size 150 mm decorative type fixed with walls complete all as specified and directed by engneer in charge 105 s&fin repair pvc connections 15 mm size with ptmt nuts of length 450 mm long all as directed. 106 s&f in repair, shower rose, 125 mm size, brass chromium plated withsweivel joint complete all as specified and directed by engr in charge. 107 m&l for 75 mm thick pcc 1:3:6 type c 2 using 40 mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10 mm wide, 30 mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as directed. 108 dismantling water tank exc 250 but n. exc. 500 litre capacity any type and remove from sitecomplete all as specified and directed by engineer in charge. 109 dismantlingwater tank exc 500 but n. exc. 1000 litre capacity any typeand remove from sitecomplete all as specified and directed by engineer in charge. 110 s&f for rotational moulded polythene water storage tank 500 ltr capacity vertical with closed top hoisted and fixed in position all as specified in ssr part i complete all as specified and directed by engineer in charge. . 111 s&f for rotational moulded polythene water storage tank 1000 ltr capacity vertical with closed top hoisted and fixed in position all as specified in ssr part i complete all as specified and directed by engineer in charge. . 112 s&fin repairs20 mm ball valves high pressure of ptmt with epoxy coated aluminium rod & high density plastic bal screwed for iron pipe and fixed. ( minimum weight 15mm 142 gms / 20mm 210 gms / 25mm 455gms ) 113 s&f for tmt bars ( fe 500d ) 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips all as specified and directed. 114 demolition of cement concrete in ground floor and paving n.exc 15cm in thickness ( below or above ground level ) all as specified. 115 m&l for 75 mm thick pcc ( 1:3:6 ) type c2 using 40mm graded stone aggregate as in sub base below floors all specified and directed. 116 m&l pre cast pcc 1:2:4 type b 1, using ( 20mm graded stone aggregate ) as in kerb stone size 300 mm x 300 mm x 100 mm with plain fair face, including chamfers, weathering, throating etc setting in cm 1:4 complete all as specified and directed. 117 m&l machined pressed precast concrete interlocking paver block glossy with grey cementand pigment, any shape and size confirming to is 15658 2006 of 60mm thickness m 35 grade with over fazilka sand cushion all as specified and directed. ( sand will be measured and paid seperatly ) 118 suply onlyfine aggregate ( sand ) for cushioning ( fazilka sand ) all as specified and directed 119 m & l plain cement concrete type b 2 1:2:4 using 20 mm graded stone aggregate as in 40 mm thick flooring finished surfaces even and smooth without using extra cement complete for all as specified and directed 120 dismantling asbestos cement ( corrugated, semicorrugated, etc. ) sheets in roof coverings all as directed. 121 s & f pre painted galvatume aluminum zinc coating gi based corrugated / semi corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified 122 s & f pre painted galvatume aluminum zinc coating gi based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified 123 excavation in trenches n.exc. 1.5m wide and n.exc 1.50 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out in getting out in sof / loose soil all as directed. 124 removal of excavated surplus spoil to a distance n.exc 50m and deposting where directed at level not exceeding 1.5 m above the starting point complete all as specified & directed by engineer in chargeq 125 returning, filling in, including spreading levelling including watering & well ramming in layers n. exc 25 cm any type of soil complete all as specified and directed by engineer in charge 126 s & f for 2 mm thick fibre glass reinforced translucent plain sheeting with 15 cm side lap fixed with coach screw and washer in roof, wall etc 127 m&l for pcc 1:2:4 type b1 using20mm graded aggregates as in benching / haunching ofmanholes including forming channels including necessary formwork etc. 128 m&l for pcc 1:2:4 type b1 using20mm graded aggregates as in coping and the like including weathering slightly rounded or chamfered angles and throating, as directed including necessary formwork etc. 129 m&l precast cement concrete 1:2:4 type b1 using 20mm graded stone aggregate and set cement mortar 1:6 as in cover slabs ( for manholes etc ) , chajjas, shelves and similar articles with plain faces all as directed 130 m&l moorum / red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed by engr in charge. 131 supply and laying dwcpe ( sn8 ) 150 ( id ) mm diameter drain pipes as per is 16098 ( part ii ) , laid in trenchesand including over 100 mm moorumbed to required slope, including all accessories / fittings, jointing and tested complete all as specified and as directed by engineer in charge. note:dwcpe pipe should be isi marked as approved by engr in charge. 132 dismantling wall and ceiling boards ( fibre, pulp, insulation etc ) or insulation boards / slabs / blankets of any thickness including cover fillets complete all as specified and directed. 133 s&f armstrong mineral fiber accoustical suspended ceiling system with anf ( micro look ) ege tiles with arm strong silhouette exposed grid. the tiles should have humidity resistance ( rh ) of 90%. nrc 0.5%. light reflectance shall be more than 85% thermal conductivity k=0.052 0.057 w / mk. colour shall be white, fire perfomance class 0 / class 1 ( bs 4760 in module size of 600mmx600mmx15mm with bioblock coating on the face of tiles. suitable for green building application with recycle content of 63% the tiles shall be laid on arm strong silhouette profile grid system with 15mm with flanges incorporating 6mm central revel in white / black colour and with a web height of 45mm and and load carrying capacity of minimum 15.68kg / sqm.silhouette , main runner and cross runner shall have mitred end and birdsmouth notches to provides mitred juction. the tee section hace a galvanised of 125gms / sqm complate all as specified and directed by engineer in charge. 134 dismantling timber scantling 40 sq cm and over in section framed work, in any position 135 s&f for 4.8 mm thick sheet glass, ordinary quality and glazing with aluminium snap beading of any size of glass in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufactuers complete all as specified & directed. ( aluminium snap beading & neoprene gasket / rubber packing not included in this items 136 s & f powder coated standard aluminium anodised grill size of mesh 75 mm x 75 mm and 8 mm thick section using u channel 25 x 12 mm all as specified and directed. 137 s & f 4 lever brass body mortice lock, vertical type, size 100 mm complete all as specified and directed. 138 s & f door closer aluminium ( die cast ) body hydraulically regulated designation no 3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed 139 e / m portiontaking down carefully copper / aluminium point wiring ( light, socket or power ) complete ( fittings such as switches, ceiling roses, pendants, regulatos, sockets etc to be measured separately ) , and making good disturbed surfaces of walls, floors etc to match with existing surfaces. 140 taking down mcb with sheet metal enclosure, main switch, db, etc and making good disturbed surfaces to match with existing surfaces. 141 taking down sub main wiring of any size / capacity complete all as specified and making good disturbed surfaces to match with the existing surfaces 142 m&l for concealed point wiringfor one light point controlled by one, oneway switch with single core pvc insulate, unsheathed multistranded copper conductorcable of size 1.5 sq.mm ( frls ) drawn in and including electrical grade pvc conduit20 mm dia concealed on wall / ceiling / floorincluding pvc insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm ( frls ) including ms shunk sheet metal box with 3 mm thick bakelite plastic laminated sheet top cover with brass counter shunk screws with washercomplete all as specified. note quoted rate shall include making good to the disturbed surfaces including plastering andpaintingto match with the existing colour. 143 , ditto all as per serial item no 143 above, but for one ceiling / exhaust fan point controlled by one switch and regulator complete all as specified and directed by engr in charge. 144 , ditto all as per serial item no 143 above, but for one bell / buzzer point controlled by one bell puch complete all as specified and directed by engr in charge. 145 , ditto all as per serial item no 143 above, but for one 3 pin 5 amps switch socketon same board with other switches complete all as specified and directed by engr in charge. 146 , ditto all as per serial item no 143 above, but for one 3 pin 5 amps switch socket outlet point on independent board complete all as specified and directed by engr in charge. 147 , ditto all as per item no.143above but point wiring with 4 sqmm multi stranded conductor cable and 2.5 sqmm unsheathedcopper conductor earth wire for two in one 5 pin 15 amp socket outlet on indep board. 148 supply and fix switch, piano type, single pole, one way 5 / 6 amp rating 230 / 250 volts grade on top covers ( catered in point wiring above ) 149 supply and fix piano socket 2 in 1, 2 / 3 pin 6 amp flush type 250 volts ac complet all as specified and as directed 150 supply and fix piano socket 2 in 1, 3 pin 5 amp and 15 amp flush type 240 volts ac complet all as specified and as directed 151 supply and fix piano swith 15 amp flush type 240 volts ac complet all as specified and as directed 152 s & f led light fitting 1 x 20 w, 230 v integral sleek polycarbonate led channel with white acrylic cover incl making connection complete. 153 s & f led 2 x 2 flat panels to enhance the delight of occupants with fittings recess mounting complete all as specified and as directed. 154 supply and fix lamp holder insulated body with back plate for angle / batten fitting with ledof 09 watt complete all as specified and as directed. 155 supply & fixingbell push switch 6a, all as specified and directed by engineer in charge 156 supply and fix bell ac 230 vott single pole complete all as specified and directed 157 supply and fix ceiling rose surface bakelite two to three terminals / plate 5 amps complete all as specified and directed by engr in charge. 158 supply and fix fan regulator electronic solid state with steps suitable for 1200 / 1400mm sweep ceiling fan working on 230 volt ac complete all as specified and directed 159 supply and fix verticle mcb db tpn 415 volts 4 way with 200 amps bus capacity double door incl fixing on wooden board or recessed on wall complete all as specified and as directed 160 supply and fix sheet metal enclosure db single pole and neutral for 240 volts 8 way double door with 200 amps rated busbarflush / surface mounting double door complete all as specified and directed 161 supply and fix mcb sp 240 volt 5 32 amp 10ka complete all as specified and as directed. 162 supply and fix mcb sp & n240 volt 5 32 amp 10ka complete all as specified and as directed. 163 supply and fix mcb sp240 volt 40 amp 10ka complete all as specified and as directed. 164 supply and fixing pvc blanking plates one way with internal lock complete all as specified and as directed. 165 material & labour for sub main wiring with two run single core 6 sqmm pvc insulated unsheathed ( frls ) cable with stranded copper conductor drawn in pvc conduit & accessories suitable size with and including 6 sqmm copper green colour earth wire all as specified and directed by engineer in charge.note two run of 6 sq.mm & one run of 4 sq.mm & one run of pvc conduit with accessories shall be measured as one length. 166 m&l for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to earth lead ofgi wire 4 mm dia ( 8 swg ) by means of bolts, nuts and washers of the earth wire.galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia and water pipe 20mm dia gi light grade with funnel and wire mesh, pcc chamber in cement concrete ( 1:2:4 ) type b 1and ci cover with frame all as shown in electrical plate no. 3 of mes schedule part i of ssr 2009. notes : ( i ) 20 mm dia gi pipe for watering to be provided with a socket and plug and should be 10 cms above ground level. ( ii ) outer edge of earth pit will be 1 metre away from the outer edge of pcc chamber. ( ii ) gi wire upto dbs earth connection is included in this item. ( iii ) water pipe shall be provided in slanting position 167 supply and fix sheet metal enclosure db single pole and neutral for 240 volts 8 way with 200 amps rated busbarflush / surface mounting double door complete all as specified and directed 168 note: the contract sum shall be calculated by deducting the amount shown in credit schedule attached to this tender, from total amount of schedule a / boq...
17
Council Of Scientific And Industrial Research - Rajasthan
39172958 tender for providing power supply and lightning in new shed at near old auditorium at csir ceeri, pilani.; 1 wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required. 2 group c ( irrespective of any length ) 3 supplying and drawing following sizes of frls pvc insulated copper conductor, single core cable in the surface / recessed steel / pvc conduit as required. 4 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire 5 2 x 4 sq. mm + 1 x 4 sq. mm earth wire 6 supplying and drawing following sizes of frls pvc insulated copper conductor, single core cable in the existing surface / recessed steel / pvc conduit as required. 7 3 x 1.5 sq. mm 8 4 x 1.5 sq. mm 9 5 x 1.5 sq. mm 10 supplying and fixing of following sizes of medium class pvc conduit along with accessories in surface / recess / angle iron on high roofwith clamp including cutting the wall and making good the same in case of recessed conduit as required. 11 20 mm 12 25 mm 13 32 mm 14 supplying and fixing following size / modules, gi box alongwith modular base, cover & blankingplate for modular switches in recess etc. as required. etc as required. 15 6 module ( 200mmx75mm ) 16 8 module ( 125mmx125mm ) 17 12 module ( 200mmx150mm ) 18 supplying and fixing suitable size gi box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5 / 6 & 15 / 16 a modular socket outlet and 15 / 16 a modular switch, making connections and testing etc. as required. 19 supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 20 5 / 6 a switch 21 supplying & fixing of 3pin, 5amp. ceiling rose / connector on juction box with provinding round phinolic sheet, including making connections etc. as required. 22 supplying of recessed mounted 36 watt soft / full glow, slim energy efficient, green square 2x2 led lightingluminaires type rc360b led36s 6500 v3 w60l60 od240v, philips or equivalent make complete with hanging arrengment all accessories, metallic crca powder coated housing etc. complete as required. 23 installation, testing and commissioning of above led tube light fittings complete with all accessories on ressesed / ceiling or suspended from ceiling upto 20 feet hight including providing hanging arrangment with clutch wire, transperent connection wire / 1.5sq.mm fr pvc copper conductoretc. as required. 24 supply of xlpe insulated pvc sheathed 1.1 kv. grade copper conductor armoured cableis: 7098 part 1 of approved make. 25 4 x 10 sqmm. copper cable 26 providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. 27 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade on wall / roof / duct / shaft including fixing by means of screws & rag bolts, suitable size ms u clamps complete as per specifications, repairing works etc as reqd. of following sizes of cables. 28 upto 35 sqmm. ( clamped with 1mm thick saddle ) 29 supply& making one end termination with heavy duty single compression brass gland sibg type, aluminium / copper lugs duly crimped with crimping tool, pvc tape etc. for following size of xlpe insulated & pvc sheathed aluminium / copper cable of 1.1 kv grade as required. 30 4 x 10 sqmm. copper cable 31 supplying and fixing of , 8 wayspn, double door, sheet steel, mcb distribution board, 415 volts on surface / recess, incomer 1no. 1 no.. dp rccb 25a, 240 volts, having a sensitivity current 30 milliamperes, outgoings 1no. 40 amp dp isolator 4 nos.sp ac mcb 10 32a, 10ka, 240v ( c curve ) , terminal blocks, duly prewired with suitable size frls pvc insulated copper conductor upto terminal blocks, tinned copper bus bar, seperate neutral links , earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted, making internal db terminations with copper lugs including all the existing incoming / outgoing connections, earthing, testing, repair & making good the wall with matching colour distemper / white wash etc. as required....
18
Public Works Department - Rajasthan
39130285 tender for white wash & painting work in qtr. no. j / ii 15 under sub dn gandhi nagar iv jaipur. ( sanction work ) ...
19
Military Engineer Services - Rajasthan
38911722 tender for welcome maintenance of offers married accommodation in central area at ge nasirabad. 1 m & l for preparation of old plastered or unplastered surfaces of wall including cornices etc applying one coat of white wash complete all as specified and directed. 2 all as per srl item no 1.00 here in before but one coat of white wash on ceiling 3 m & l for washing rubbing down and stopping distempered surfaces of wall and applying one coat of oil bound distemper white or tinted complete all as specified and directed. 4 m & l for complete removal of existing treatment of old plastered surface of wall andapplying two coats of oil bound distemper over a coat of 1mm thick putty ( jk / birla ) complete all as specified and directed. 5 m&l for preparation of old surface of wood and wood based material of any description over 10cm width or girth and applying one coat of synthetic enamel paint ( 1st quality ) complete all as specified and directed. 6 m&l for preparation of old surface of steel or iron based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint ( 1st quality ) complete all as specified and directed. 7 m & l for washing rubbing down and stopping of old painted surfaces, removing nails, making good holes, cracks etc and applying one coat of cement base paint complete all as specified and directed. 8 m & l for complete removal of existing treatment and applying two coats of weather proof acrylic emulsion paint over a coat of 1mm thick wall care putty including a coat of emulsion wall primer all as per manufactures instructions complete all as specified and directed.make : asian, apex and berger or equivalent as approved by ge 9 m & l for complete removal of existing treatment of oldsurface of manglore tiles and applying two coats of terracotta roof paint complete all as specified and directed. make : apex / berger 10 taking down cement or cement lime plaster from stone / brick wall, ceiling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 11 dismantling floor, hearth or wall tiles including cement mortar and rubbish off the premises, complete all as specified and directed. 12 demolition of brick / stone masonry built in cement or cement lime mortar in any description complete all as specified and directed. 13 demolition of cement concrete ( unreinforced ) in floors and paving n.exc 15cm thickness ( above or below ground level ) complete all as specified and directed. 14 hacking out old broken glass ( any thickness, size quality or description ) from metal frame including punching or drilling out old glazing, pins, spring clips & providing & fixing new ones and s&f 3.00 mm thick sheet glass, ordinary quality & glazing with oil putty not exc0.50 sqm each pane complete all as spd & directed. 15 hacking out old broken glass ( any thickness, size quality or description ) from metal frame including punching or drilling out old glazing, pins, spring clips & providing & fixing new ones and s&f 3.00 mm thick figured glass, ordinary quality & glazing with oil putty not exc0.50 sqm each pane complete all as spd & directed. 16 taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) n. exc 1.50 sqm each and removing from site complete all as spd & directed and making good disturbed surface of walls in cement mortar ( 1:3 ) complete all as specified and directed. 17 taking down chowkhats or frames with shutters ( without taking off shutters from the frames ) exc 1.50 sqm and n.exc 4.00 sqm each and removing from site complete and making good disturbed surfaces of wall in cm ( 1:3 ) complete all as specified and directed. 18 taking down shutters of any description exc 1 sqm and n.exc 2 sqm each leaf and removing from site complete all as specified and directed 19 m & l for rendering 15mm thick in cm ( 1:6 ) on stone masonry surfaces wall finished even and smooth without using extra cement or surface other than fair face of brick work or on one side of lathing complete all as specified and directed. 20 m & l for rendering 10mm thick in cm ( 1:3 ) on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed. 21 m & l for 15mm thick rendering in cm ( 1:4 ) on brick / concrete surface mixed with water proofing compound @ 3% by weight of cement & surface fair and even complete all as specified & directed. note : wpc will be measured and paid separately 22 m & l for 15 mm thickrough cast plaster mix with crusted stone ( 6 10 mm ) , sand and cement in the ratio 1:1:1 , over 10 mm thick rendering in cm 1:4 as in under coat including dubbing coat ( if required ) complete all as specified and directed. 23 m&l for stone walling of random rubble, uncoursed, well bonded, bedded & solidly hearted, built in cm ( 1:6 ) complete all as specified and directed. 24 all as per sl item no 23.00 here in before but except stones.note: old servieable stones retrieved vide sl item no 12.00 shall be reused. 25 m & l for brick work with fly ash bricks, straight or curved on planto any radius, in half brick thick wall built in cm 1:4 complete all as specified and directed. 26 m & l for brickwork with fly ash bricks, old size, straight or curved on plan exc 6 m mean radius, built in cm 1:6complete all as specified anddirected. 27 dismantling loose / disintegrated portion of rcc chajjas bends shelves, beams balconies and similar work at any position or any height and dubbing out with pcc ( 1:1.5:3 ) , 15mm to 50mm thick using 6 to12mm graded stone aggregate to make up and finished to required shape including applying anti corrosive paint on exposed surface of reinforcement, provision of necessarysupports, form work and 10mm thick plastering in cm ( 1:4 ) finished fair and even complete all as specified and directed. 28 m&l 25mm thick pcc ( 1:2:4 ) type b 0 using 12.5mm graded stone aggregate as in floorcomplete all as specified and directed. 29 m & l for non skid ceramic coloured tiles ( joint free ) , 7 to 8 mm thick ( square / rectangular ) , area of each tile exc 0.18 sqmbut not exc 0.38 sqmin floors etc set and jointed in neat cement slurryand pointed inwhite cement mixed with pigments to match the shade of tile laid over and including screed bed 15 mm thick in cm ( 1:6 ) complete all as specified and directed. 30 m & l for non skid ceramic coloured tiles ( joint free ) , 7 to 8 mm thick ( square / rectangular ) , area of each tile exc 0.11 sqmbut not exc 0.18 sqmin floors etc set and jointed in neat cement slurryand pointed inwhite cement mixed with pigments to match the shade of tile laid over and including screed bed 15 mm thick in cm ( 1:6 ) complete all as specified and directed. 31 m & l for vitrified ceramic tiles light shade 10mm thick ( square / rectangular ) polished area of each tiles exc. 0.18 sqm but n.exc 0.36sqm in floor, set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with the shade of tile laid over and including screed bed 15mm thick in cm ( 1:6 ) complete all as specified and directed. 32 all as per sl item no 31.00 here in before but on vertical surfaces of stone wall such as dados, skirting etc set& jointed in neat slurry and pointed inwhite cement mixed with pigments to match the shade of tile over & including 10 mm thick screed plaster in cm 1:4 complete all as specified and directed. 33 m & l for glazed ceramic coloured tiles, 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on vertical surfaces of wall such as dados, skirtingsetc set and jointed in neat cement slurry and pointedin white cement mixed with pigments to match with the shade of tile over and including 10mm thick screed plaster in cm ( 1:4 ) complete all as specified and directed. 34 all as per sl item no 29.00 here in before but on vertical surfaces of stone wall such as dados, skirting etc set& jointed in neat slurry and pointed inwhite cement mixed with pigments to match the shade of tile over & including 10 mm thick screed plaster in cm 1:4 complete all as specified and directed. 35 m&l for 16 18 mm thick granite ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking platform and like set & jointed in neat cement slurry & pointed in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite including rounding the exposed edgeslaid over & including 15mm thick screed bed in cm ( 1:6 ) complete all as specified and directed. 36 m & l for rolled mild steel work angle iron ( 40x40x6mm ) as in door frame ( chowkhats ) including provn of 10mm dia deformed bar welded horizontally to bottom of frame confirming to fe 210 gde e 165 including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed 37 s & f second class hw ( hollock / bansum / sal ) , plain, solid, straight, chowkhats & frames, wrought, framed, rebated on the solid, rounded or chamfered, put together glue pinned at joints complete all as specified and directed. 38 s & f hold fast of flat iron 25x6mm conforming to fe 210 gde e 165including preparing the surfaces & treated with coaltar & sanded with clean sharp sand complete all as specified & directed 39 raking out joints / pointing to random rubble or polygonal rubble stone masonry uncoursed or brought upto courses built in cm and m & l for raised pointing in cement mortar ( 1:4 ) complete all as specified and directed. 40 taking down shutters of any description exc 1 sqm and n.exc 2 sqm each leaf& refixing in the same opening after necessary resecuring or easing & adjusting etccomplete all asspecified and directed. 41 taking down shutters of any description exc 2 sqm each leaf& refixing in the same opening after necessary resecuring or easing & adjusting etc complete all asspecified and directed. 42 s & f 30mm thick flush shuttersolid core construction with block board core and ply wood face panels with commercial face on both sides including 6mm thick iind class hard wood lipping on edges complete all as specified and directed. 43 s & f second class hw hollock / bansum / sal, 35 mm thick, glazed and skeleton shutters, factory made open rebated ( three panels ) and prepare to receive glass, gauge etc without sash bar, edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. size of members of shutter shall be as specified in ssr part i, section 8 clause 8.24 ( a ) member shall be kiln seasoned & chemically pressure treated complete all as specified and directed. 44 s&f factory made pvc solid frame of size 50mmx47mm made out of 5mm prelam pvc sheet & edges will be painted to match with prelam sheet reinforced with m.s. square tube and fixing in opening as per specification & drawing as perssr 2020 complete all as specified and directed. 45 s & f factory made solidpvc mouldeddoor shutter with wood free eps, 28 to 30mm thick, ( styles ) with 2 raised panel design with 2mm thick moulded prelaminated pvc sheeton front face & 2mm thick plain colour pvc sheet on back face, and fixing in the frame at site as per specification and drawings on page 161 of ssr ( part ii ) 2020 complete all as specified and directed. 46 s & f in repair steel window / ventilator factory made, made out of ms hollow section 79mmx39mmx1.6mm thick frame with double shutters ( glazed & wire gauge shutters ) made out of z section using flush butt welding & tenon riveting all as per is 1038 / 83, dobby hinges shall be provided to both shutters. locking arrangements as per sample approved by ge, provided with knob, 10mm ms square bars in grills, z section handle 100mm sized & 150mm long hook & eye welded to frame & shutter, four nos lugs welded to frame including necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fasts and making good in pcc 1:2:4 type b 1 including preparation of surfaces & applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed.note : wire mesh and sheet glass shall be measured & paid separately under respective items. 47 taking down of old boards and s & f 18 / 19mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice lamination, fixed with screws including teak wood lipping 19 x 6mm thick fixed with nails in shelves, partition and palmet boxes, shelves, almirah book cases, toilet boxes, racks, cup board shutter and similar works complete all as spepcified and directed. 48 s & f aluminium alloy, anodised sliding door bolt, 300mm long, isi marked, with hasp and staple ( bolt type ) and fixing bolts and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed. 49 s & f in repairs aluminium alloy, anodised sliding door bolt, 300mm long, isi marked, with hasp and staple ( bolt type ) and fixing bolts and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed. 50 s&f mild steel butt hinges, medium weight, cold rolled, isi marked of size 125 mm complete all as specified and directed. 51 s&f in repairs mild steel butt hinges, medium weight, cold rolled, isi marked of size 125 mm including necessary welding work etc complete all as specified and directed. 52 s&f aluminium, anodised, barrel tower bolt of extruded section, isi marked, 150 mm long complete all as specified and directed. 53 s&f in repairs aluminium, anodised, barrel tower bolt of extruded section, isi marked, 150 mm long complete all as specified and directed. 54 s&f 150 mm long extruded aluminium alloy handle fabricated type anodized complete all as specified & directed. 55 s&f in repairs 150 mm long extruded aluminium alloy handle fabricated type anodized complete all as specified & directed. 56 s & f stainless steel wire cloth0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staple complete all as specified and directed 57 s & f in repairs stainless steel wire cloth0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staple complete all as specified and directed 58 s & f in repairs floor door stopper aluminium alloy body & tongue of size 140mm, anodised with hard drawn spring, fixed in door, over all length of cover plate of complete all as specified and directed. 59 taking down the existing material and s&f 300 mm rat tail rod mild steel ordianarypattern springs including roller and roller plate complete all as specified and directed. 60 s & f in repairs 100mm size hasp and staple, aluminium anodised, safety type including bolt to hinge plate complete all as specified and directed 61 s & f in reapirs25mm dia ms chromium plated curtain rod powder coated tubular, fancy type, complete all as specified and directed. 62 s&f in reapirs ms chromium plated powder colour coated, decorative type knobs with bracket fixed at end of pelmet rod suitable for 25mm dia complete all as specified and directed. 63 dismantling of exisiting unserviceable rcc / pvc water tank of capacity not exceeding 500 litre each s&f 500 litre capacity rotational moulded polyethylene water storage tanks double layered ( cylindrical vertical with closed top ) isi marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in ssr part i. 64 dismantling of exisiting unserviceable rcc / pvc water tank of capacity not exceeding exc 500 but n. exc 1000 litre each s&f 1000 litre capacity rotational moulded polyethylene water storage tanks double layered ( cylindrical vertical with closed top ) isi marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in ssr part i. 65 taking out old unserviceable water closet ( squatt pattern ) and s & f vitreous china, squatting panorissa pattern size 580x440mm, white with integral foot rests ( excluding flushing cistern and flush pipe ) with chinaware ‘p’ or ‘s’ trap, front or back inletincluding connection to trap and to flushing pipe, anti syphonage pipe and making good the floor to match the existing completeall as specified and directed. 66 taking out old unserviceable water closet and s & f vitreous china wash down closet pan ( pedestal pattern ) , white, including plastic cover white closed pattern whith flat bottom and mild steel chromium plated / pvc hinge device including connections to drain ( or outgoing pipe ) and to flushing pipe, anti syphonage pipe etc complete all as specified and directed. 67 taking down old unserviceable whb and s&f vitreous china, white, wash hand basin flatback of size 550 x 400mm complete all as specified and directed 68 demolition of cement concrete ( unreinforced ) in any position & of any description from sunken floor ( ground or 1st floor ) and removing and depositing materials exc 50mtrs level not exc. 1.5m above the starting point complete all as specified and directed. 69 m & l for cement concrete 1:5:10 type e2 using 40mm graded stone aggregate as in sunken floors filling and mass concrete complete all as specified and directed. 70 m&l 20mm thick cement plaster in cm 1:4 mixed with water proofing compound @ 3% and applying water proffing treatment on sunken portion with acrylic based polymer modified cementitious composit compound as specified and approved & cement slurry two layers, 1st layer @ 0.488 kg / sqm mixed with composit compound @ 0.253 kg / sqm & the second layer slurry @ 0.242 kg / sqm mixed 0.126 kg of compound complete with min 4 hours allowed to air cure between these layers and applying 200 polyflim with adhesive complete all as specified and directed. 71 m&l for 50mm thick pcc ( 1:3:6 ) type c 1 using 20mm graded stone aggregate as in plinth protection finished fair and even laid in alternatebays n.exc 2m in length and joints filled with bitumen mastic 1:3 ( 1 bitumen :3 sand ) complete all as specified and directed. 72 s & f in repair pvc valve less, syphonic action type flushing cistern, isi marked, 10 litre capacity, low level, white / ivory colour, with inlet, ball valve, float, handle fixed with pvc rawl plug of suitable size complete all as specified and directed. 73 s & f in repair pvc flush pipe of approved quality 32 mm bore, for low level flushing cistern complete all as specified and directed. 74 s & f in repair brass chromium plated shower rose of 100mm size with swivel joints, including fixing to steel pipe or union complete all as specified and directed. 75 taking down old unserviceable pvc connectionand s & f pvc connection, heavy duty 15 mm bore, 45 cm long with two nos ptmt nuts at both ends of approved quality complete all as specified and directed 76 s&f in repair pillar tap, 15mm bore, cast copper alloy, chromium plated, isi marked, screwed down high pressure with or without lettred hot or cold with long screw shanks and fly nuts screwed for iron pipe complete all as specified and directed 77 s&f in repair stop / angle valve 15mm bore cast copper alloy, chromium plated, isi marked with long crutch or butterfly handle screwed down high pressure screwed both ends for iron pipe complete all as specified & directed. 78 s&f in repairs 25mm bore gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipes and fixed all as directed. 79 taking down old unserviceable waste pipe and s&f 32mm bore pvc waste pipe of 75mm length with oneend socketed complete all as specified and directed. 80 s & f in repairs grating square / round 140mm size of ptmt with centre hole movable or side hole for fix to waste pipe ( minimum weight 50 gms ) complete all as specified and directed. 81 s & f in repairs 15 mm bore bib taps standard of ptmt any colour, screwed for iron pipe and fixed complete all as specified and directed. 82 taking down old unserviceable water closet seat cover & s&f plastic water closet seat cover, white, closed pattern with flat bottom and cover & mild steel chromium plated or aluminised hinging device complete all as specified and directed. 83 taking down old unserviceable kitchen sink and s&fkitchen sink with drainage board overall size not less than 915x460mm, bowl size 410x 330x160mm made of stainless steel 1.00 mm thick with plugs, washers and waste including fixing cantilever brackets and connecting union complete all as specified and directed.note : minor variation in dimension + 20mm as per standard catalogue of manufacturer may be approval of ge in writing without price adjustment. 84 s & f in repairs stainless steel plate rack made of 0.50mm thick of over all size914mm x 609 mm x 255 mm and weight not less than 7.00 kg each of approved quality complete all as specified and directed.note : minor variation in dimension may be permitted as per standard manufacturing models of manufacturer without price adjustment with prior approval of ge but weight shall not be less than 7.00 kgs. 85 s & f waste coupling cp 32mm dia for glazed ware basins etc with long screwed shanks and fly nuts flanged etc complete all as specified and directed. 86 s & f in repair bib taps isi marked, cast copper alloy, chromium plated, isi marked with crutchor butterfly handle, screwed down, screwed for iron pipeor for brass ferrule and fixed for 15 mm boreof pipe complete all as specified and directed. 87 s & f in repair pvc ( swr ) floor trap with grating 75 mm dia, plain with grating including jointing with solvent cement complete all as specified and directed. 88 taking down old unserviceable mirror and s & f looking mirror of size 600 mm x 450 mm x 5.5mm thickof selected quality, mounted on pvc frame and fixed to and including wooden plugs with chromium plated brass screwswasher cup washer complete all as specified and directed. 89 s & f in repair tubular towel rail, chromium plated brass 20mm dia ‘d’ type 60cm long between flanges complete all as specified and directed. 90 s & f in repair for toilet fittings chromium coated towel rack 600mm long without lower haners but three hookscomplete all as specified and directed. 91 s & f in repair brass wall mixer 15mm bore cast copper alloy chlromium plated wall each mixer with hot and cold water with crutch handlecomplete all as specified and directed. 92 s & f in repair for toilet fittings corner glass shelf with bracket complete all as specified and directed. 93 s & f in repair for toilet fittings wall mixer ( wall mounted model ) with teliphonic shower rose complete all as specified and directed. 94 s & f in repair for toilet fittings wall teliphonic shower with 1.5 mtr long flexible tube & swivel wall hookcomplete all as specified and directed. 95 s & f in repair for toilet fittings health faucet with 1.2mtr long flexible tube & swivel wall hook complete all as specified and directed. 96 s & f in repair for pvc cabinet of size 422mm x 622mm with mirror of good quality with shelves in bath fixed complete to wallscomplete all as specified and directed.make : prayag cat no. 555 or make and model are equivalent as approved by ge. 97 s & f in repair for toilet fittings two way bib cock of 15mm bore complete all as specified and directed. 98 taking up or down steel tubing and connection 15mm bore keeping aside for reuse or removingto store complete all as specified and directed. 99 all as per srl item no 98.00 here in before but 20mm bore 100 all as per srl item no 98.00 here in before but 25mm bore 101 supply and fix mild steel water tubing 15 mm dia galvanised medium grade including all fittings ( such as bends, tees, short pieces connectors, elbows, reducers, unions, sockets etc ) and fixed to walls / ceilings / laid on floors including testing complete all as specified and as directed. 102 all as per srl item no 101.00 here in before but 20mm bore 103 all as per srl item no 101.00 here in before but 25mm bore 104 refixing only 15mm bore old gi tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, tee, union, socket, reducer etc complete all as specified and directed. 105 all as per srl item no 104.00 here in before but 20mm bore 106 all as per srl item no 104.00 here in before but 25mm bore 107 supply only liquid water proofing compound, isi marked complete all as specified & directed 108 m&l in repairs for 2nd class hard wood plain fillets, square , rectangular or triangular area exec. 6 sqcm but n. exec 13 sqcm in sectional, clean sawn, secured with nails complete all as specified and directed. 109 s & f in repairs 75mm bore pvc ( swr ) pipe single socketed in any length with rubber ring joints fixed to wall isi mark, complete all as specified and directed. 110 s & f in repairs 110mm bore pvc ( swr ) pipe single socketed in any length with rubber ring joints fixed to wall isi mark, complete all as specified and directed. 111 s & f in repairs 75mm bore pvc ( swr ) bend / shoe with oval access door of any radius complete all as specified and directed. 112 s & f in repairs 110mm bore pvc ( swr ) bend / shoe with oval access door of any radius complete all as specified and directed. 113 s&fin repair 75mm bore pvc ( swr ) junction single ( single t ) equal or unequal complete all as specified and directed. 114 s & f in repairs 110mm bore pvc ( swr ) junction single ( single t ) equal or unequal complete all as specified and directed. 115 m&l for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over & including one coat of 1mm thick cement putty complete all as specified & directed.. 116 m&l for preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified & directed. 117 m & l for preparation of newly plaster surfaces of wall& applying two coats of cement base paint over a coat of primer complete all as specified and directed. 118 m&l for preparation of new steel surfaces of any description over 10 cm width or girth applying two coats of synthetic enamel paint ( 1st grade ) over a coat of red oxide primer complete all as specified. 119 m&l for preparing the new wooden surface of any description over 10 cm width or girth & applying two coats of synthetic enamel paint ( 1st grade ) over one coat of pink primer complete all as specified & directed. 120 s&f in repair jet flush including plate and coonection pipe complete all as specified and directed. 121 m&l for machine cut kota stone slab flooring of size 550mm x 550mm 20 25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishinglaid over & including 15mm thick screed bed in cm 1:6 complete all as specified & directed. 122 m&l for kota stone slab 20 25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & mirror polishing in riser of steps, skirting, dado and pillar laid over & including cement screed 10mm thick in cm ( 1:4 ) complete all as specified & directed. 123 only on old surfacesmirror polishing on marble / granite / kota stone where ever required to give high gloss finish complete all as specified & directed. 124 m&l for crack repair in wall, ceiling and roof with cm 1:3 mixed with water proofing compound @3% by weight of cement, width of crack is 25mm and 50mm deep including necessary demolition and making good disturbed surfacecomplete all as specified & directed.note : wpc measured and paid separately 125 supply and fixing in repairs18mm thick ( one side decorative lamination & other side balancing lamination sheet density 600kg / m3 ) solid pvc board with edge bending on edgeswith cement solvent adhesive for shutter / kitchen cabinet / cup boards / partition wall / wall cabinet and similar work completeall as specified and directed. make : rajshree / kitply / century or equivalent as approved by ao. 126 supply and fixing in repairs12mm thick ( one side decorative lamination & other side balancing lamination sheet density 600kg / m3 ) solid pvc board with edge bending on edges with cement solvent adhesive for shutter / kitchen cabinet / cup boards / partition wall / wall cabinet and similar work complete all as specified and directed.make : rajshree / kitply / century or equivalent as approved by ao. 127 s&f stainless steel soft close hinge with assembly, complete all as specified and directed.make : godrej code no. 5070 128 s&f 125 mm dia oval shape brass handle fancy type bright finish complete all as specified & directed. 129 s&f stainless steel basket ( plain ) of approved quality of size 520 x 485 x 100mm complete all as spepcified and directed. make : godrej ss 304 code no. 6154 130 s&f stainless steel plate / thali basket of approved quality of size 520 x 485 x 200mm complete all as spepcified and directed. make : godrej ss 304 code no. 6168 131 s&f stainless steel cutlery basket of approved quality of size 520 x 485 x 100mm complete all as spepcified and directed. make : godrej ss 304 code no. 6162 132 s&f stainless steel cup & saucer basket of approved quality of size 520 x 485 x 100mm complete all as spepcified and directed. make : godrej ss 304 code no. 6159 133 s&f stainless steel two shelf pull out basket of approved quality of size 150 x 485 x 430mm complete all as spepcified and directed. make : godrej ss 304 code no. 6169 134 s&f steel ball bearing basket / trolly / drawer channel 50cm long complete all as spepcified and directed.make : godrej code no. 8178 135 total in figures 136 quoted amount in words...
20
Public Works Department - Rajasthan
38744615 repair and white wash in iti building at sri ganganagar...
21
Public Works Department - Rajasthan
38448682 white wash work in minister bunglows under sub dn gandhi nagar iii jaipur ( 08 / secity / cd iii / 2216 mtc rep / 05 / 2023 24 ) ...
22
Department Of Local Bodies - Rajasthan
38411401 annual rate contract materials supply for tengible work in irgy urban scheme at various ward at different places in municipal council pratapgarh. , based on ruidp sor2022 and labour department rate , stone coarse aggregate 40 mm , white wash with lime / samosham ( 2 & more coat ) , synthetic enemal paint to give an even shade for iron / steel work , paint brush as per required size , tarpin oil , steel leaf , cotton colth ( dhoti ) , water tanker supply 5000 ltr. at site , concrete mixer with viabrator including p.o.l. , interlocking tile 60 mm thick , sand ( fine aggregate ) , cement ( 50 kg ) 43 grade opc , kerb stone precast cc m 20 grade , rcc bench with complete fixing and supply , fevicole adhesive item for white wash , stone coarse aggregate 20 mm , centring & shutring , tractor trolly with pol , plastic emulsion paint , hydraulic excavator of 1 cum bucket , vibratory roller 8 tonne with driver including pol , granular material or hard moorum for gsb works at site , grassing with carpet grass , good earth , steel work gates etc with complete fitting , stancil for wall designing , sand paper , stone for rr masonary , brick for masonary , irgy banner stancil , concrete mixer with including p.o.l. , plate vibrator with including p.o.l. , vibrator ( needle type 40mm ) with including p.o.l. , crusher broken grade ii ( 63 45mm ) , paint roller , stone boulder for pitching , wired brush...
23
Department Of Local Bodies - Rajasthan
38267682 annual rate contract materials supply for tengible work in irgy urban scheme at various ward at different places in municipal council pratapgarh. , based on ruidp sor2022 and labour department rate , stone coarse aggregate 40 mm , white wash with lime/samosham (2 & more coat) , synthetic enemal paint to give an even shade for iron/steel work , paint brush as per required size , tarpin oil , steel leaf , cotton colth (dhoti) , water tanker supply 5000 ltr. at site , concrete mixer with viabrator including p.o.l. , interlocking tile 60 mm thick , sand (fine aggregate) , cement (50 kg) 43 grade opc , kerb stone precast cc m 20 grade , rcc bench with complete fixing and supply , fevicole adhesive item for white wash , stone coarse aggregate 20 mm , centring & shutring , tractor trolly with pol , plastic emulsion paint , hydraulic excavator of 1 cum bucket , vibratory roller 8 tonne with driver including pol , granular material or hard moorum for gsb works at site , grassing with carpet grass , good earth , steel work gates etc with complete fitting , stancil for wall designing , sand paper , stone for rr masonary , brick for masonary , irgy banner stancil , concrete mixer with including p.o.l. , plate vibrator with including p.o.l. , vibrator(needle type 40mm) with including p.o.l. , crusher broken grade ii (63 45mm) , paint roller , stone boulder for pitching , wired brush...
24
Public Works Department - Rajasthan
38266855 white wash/colour work in autodoriyam main building at snkp govt. college neemkathana...
25
Public Works Department - Rajasthan
38243691 white wash and colour paint work in iii and iv type qtrs under sub dn gandhinagar 1 jaipur 08/secity/cd iii/2216 and/09/2023 24...
26
Public Works Department - Rajasthan
38235457 white wash / colour work in autodoriyam main building at snkp govt. college neemkathana...
27
Public Works Department - Rajasthan
38211721 white wash and clolour work in v and vi type qtrs. under sub dn gandhi nagar i jaipur. ( 08 / secity / cd iii / 2216 mtc rep / 07 / 2023 24 ) ...
28
Public Works Department - Rajasthan
38211710 white wash and painting work in v and vi type qtrs. under sub dn gandhi nagar iii jaipur. ( 04 / secity / cd iii / 2216 mtc rep / 07 / 2023 24 ) ...
29
Public Works Department - Rajasthan
38211198 white wash and colour paint work in iii and iv type qtrs under sub dn gandhinagar 1 jaipur 08/secity/cd iii/2216 and/09/2023 24...
30
Public Works Department - Rajasthan
38211173 white wash maintenance work in iii and iv type qtrs. under sub dn gandhi nagar iii jaipur. ( 12 / secity / cd iii / 2216 mtc rep / 09 / 2023 24 ) ...
31
Public Works Department - Rajasthan
38211168 white wash work in ja type qtrs. under sub dn gandhi nagar iii jaipur. ( 22 / secity / cd iii / 2216 mtc rep / 08 / 2023 24 ) ...
32
Kendriya Vidyalaya Sangathan - Rajasthan
38060890 bids are invited for toilet repair and installation mse white wash and painting , pipe fitting , taps , wastage pipe , dismantaling , ceramic tile work , sanitary items , brick work total quantity : 591...
33
Public Works Department - Rajasthan
38002532 white wash & painting work in qtr no. j / ii 7 under sub dn gandhi nagar iv jaipur. ( sanction work ) ...
34
Public Works Department - Rajasthan
37922761 tender for white wash and colour washing work in bajaj nagar qtrs. under sub dn. gandhi nagar iii jaipur ( 123 / secity / cd iii / 2216 mtc rep / 09 / 2022 23 ) ...
35
Public Works Department - Rajasthan
37862391 colour wash & white wash in govt. school salection for use of newly created distt. collector office....
36
Kendriya Vidyalaya Sangathan - Rajasthan
37815623 bids are invited for toilet repair and maintenance mse white wash and painting , pipe fitting , taps , wastage pipe , dismantling , ceramic tile work , sanitary items , brick work total quantity : 591...
37
Maharana Pratap University Of Agriculture And Technology - Rajasthan
37650789 white wash and minor repairing of ug class rooms 1 7 & toilets & roof treatment of smart class room of rca....
38
Maharana Pratap University Of Agriculture And Technology - Rajasthan
37631248 white wash and minor repairing of ug class rooms 1 7 & toilets & roof treatment of smart class room of rca....
39
Public Works Department - Rajasthan
37505699 white wash work in qtr no j / ii 16 under sub dn gandhi nagar iii jaipur. ( sanction work ) ...
40
Department Of Local Bodies - Rajasthan
37475687 under the indira gandhi urban employment scheme, the work of providing necessary resources / materials for the repair and renovation work of government buildings / parks / water harvesting etc. 1 painting two coats on specified surface with synthetic enamel paint of approved brand and shade, after through cleaning and neccesary filling to give even shade including all material, labour. on new plastered concrete surface ( excluding labour ) 2 painting two coats on specified surface with synthetic enamel paint of approved brand and shade, after through cleaning and neccesary filling to give even shade including all material, labour. on steel surface ( excluding labour ) 3 scraping & removing of white wash / distemper / oil paint / algli etc. from lime plaster highly decorative, ornamental and stucco work with at most care by using fine sand paper under the close supervision to keep intact the old designs. ( excluding labour ) 4 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:two or more coats on new work ( excluding labour ) 5 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete ( excluding labour ) 6 cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded 20mm nominal size stone aggregate ) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. ( collectorate, gpf office, municipal office and other govt building ) ( excluding labour ) 7 construction of water harvesting structure in nagar prashid ( excluding labour ) ...
41
Military Engineer Services - Rajasthan
37255521 welcome maintenance for offrs qtrs under age b / r ii under ge ( n ) bikaner. 1 m&l preparingof old decorated surfaces of walland applying one coat of distemper oil emuision complete all as specified and as directed by engr in charge. 2 m&l preparingof old decorated surfaces of walland applying two coat of distemper oil emuision complete all as specified and as directed by engr in charge. 3 m&l preparing surfaces of plaster or unplaster old surface of wall and applying one coat of white wash complete all as specified and as directed by engr in charge. 4 m&l preparing surfaces of plaster or unplaster old surface of wall and applying two coat of white wash complete all as specified and as directed by engr in charge. 5 m&l preparing surfaces of plaster or unplaster old surface of wall and applying one coat of white wash on ceiling complete all as specified and as directed by engr in charge. 6 m&l preparing surfaces of plaster or unplaster old surface of wall and applying two coat of white wash on ceiling complete all as specified and as directed by engr in charge. 7 m&l preparing old surfaces of wall and applying one coats of plastic emulsion paint complete all as specified and as directed by engr in charge. 8 m&l preparingold surfaces of ceiingand applying one coats of plastic emulsion paint complete all as specified and as directed by engr in charge. 9 m&l preparing old surface of wood of any desc over 10cm width or girth and applying two coats of synthetic enamel paint .over pink primer complete all as specified and as directed by engr in charge. 10 m&l preparing new surface of steel of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide complete all as specified and as directed by engr in charge. 11 m&l preparing the old painted wooden surfaces of any description over 10 cm width or girthand applying one coat of synthetic enamel paint.complete all as specified and as directed by engr in charge. 12 m&l preparing new surface of steel of any desc over 10cm width or girth and applying one coat of synthetic enamel paint over red oxide complete all as specified and as directed by engr in charge. 13 m&l complete removal of existing treatment and applying a thin layer of putty on wall surfaces complete all as specified and as directed by engr in charge. 14 m&l preparing new surface of old or new incl removal of old treatment ans applying a thin layerof plaster of paries to give a uniform finish as approved by engr in charge 15 m&l demolition of cement conc. in any description and incl any position not otherwise specially provided complete all as specified and directed 16 m&l dismanting floor, hearth or wall tiling including cement mortar bedding and removal of rubbish out of the premises complete all as specified and as directed by engr in charge. 17 hacking out old broken glass ( any thickness, size, quality or description ) fromwooden frame or stone concrete or brick surrounds glazed with putty or fixed with beads.complete all as specified and as directed by engr in charge. 18 dismantlingpipes of any desc fixed to wall or laid under floor complete all as specified and as directed by engr in charge. 19 dismantling cast iron pipes of any desc fixed to wall or laid under floor complete all as specified and as directed by engr in charge. 20 taking down cement plaster on brick or stone walls, including raking out joints, hacking for key, scrubbing down with water etc. 21 taking up or down steel tubing 15 mm diaand connections and stacking neatly for offering credit complete all as specified and as directed by engr in charge. 22 all as per item n 21 above, but 20 mm dia. complete all as specified and as directed by engr in charge. 23 taking down chowkhats or frameswith shutters ( without taking off shutters from the frames ) of size n. exc 1.5 sqm each complete all as specified and as directed by engineer in charge. 24 taking down chowkhats or frameswith shutters ( without taking off shutters from the frames ) of size exc 1.5 sqm but not exc 4.0 sqm each complete all as specified and as directed by engineer in charge. 25 taking down shutters of any description, areaexceeding 1.00 sqm and n.exc 2.00 sqm eachcomplete all as specified and as directed by engineer in charge. 26 m&l for welding in repairs n.exc 2.5 cm in length and not exceeding 6mm thick of metal complete all as specified and directed by engineer in charge. 27 s&f 1.25 mm thick pressed steel frames of size 125mm x 60mm for single doorsincluding necessary fixing lugs, hinges, lock strike plate, etc complete all as per is provns.complete all as specified and as directed by engr in charge. 28 s&f 1.25 mm thick pressed steel frames of size 105mm x 60mm for single doorsincluding necessary fixing lugs, hinges, lock strike plate, etc complete all as per is provns.complete all as specified and as directed by engr in charge. 29 s&f second classhard wood plain, framed, panelled shutters 35mm thick, ( any number of panels ) with panels of timber flat on both sides ( feather edged ) or of veneered partcile board medium density wood particle board with commercial faces venners supplied and fixed to chowkats.complete all as specified and as directed by engr in charge. 30 s&f second class hard wood, glazed and skelleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etcwithout sash bar, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing gauze etc, size of members as directedsupplied and fitted to chowkats complete all as specified and as directed by engr in charge. 31 m&l for 25 mm thick flush shutters for cupboards solid core construction, with block board core, and ply wood face panels, both faces covered with decorative face veneer with lipping to matchcomplete all as specified and as directed by engineer in charge. 32 s&f solid pvc door frame of size 50 mm x 47 mm made out of 5 mm plain colour pvc sheet reinforced with m.s. square tube suppling & fixing in opening all as specified and as directd. 33 s&f factory made solidpanel pvc door shutter 30mm thick ( style ) consisting of framemade out of ms tubes for top and bttom rails. ms frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colourpvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail, panneling of plain color pvc sheetto be fitted in the ms frame welded / sealed to the stiles &rails with suitable pvc sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site all as specfied and as directed. 34 s&f steel window / ventilators pressed steelframed ( box type ) factory made glaged and guaged with side hung shutters including pintolhinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded incl a prov of cooler / ac opening with shutter including one shop coat of red oxide primer complete all specified.note :i ) he window shall be fabricated as per drg no cebz / 888r & 889 sheet 1 to 4. ii ) ms fillets, glazing, wire gauge shall be measured and paid separately. 35 s&f framed work such as grills , framed guard bars barred iron doors ;ladders framed balusters railings and similar work conforming to fe 410 0or fe 310 0 complete all as specified and as directed by engr in charge. 36 s&f stainless steel wire cloth o.36mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples.complete all as specified and as directed by engr in charge. 37 s&f stainless steel wire cloth o.36mm nominal dia of wire and average width of aperature 1.40mm and fixed in repairwith stainless steel wire staples.complete all as specified and as directed by engr in charge. 38 m&l for second classhard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the soild, rounded or chamfered, put together with glue pinned at joints.complete all as specified and as directed by engr in charge. 39 m&l second classhard wood, in scantling wrought, in timber fixed complete all as specified and as directed by engr in charge. 40 teakwood beading 20x60mm half round complete supplied and fixed complete all as specified and as directed by engr in charge. 41 s&f 18 / 19 mmplywood, grade 1 ( with bwr resistant / termite proof ) with fixed with screws to timber frame work as in cup boards / cabinets etc complete all as specified and as directed by engr in charge. ( make : century / kitply / or other app by ge ) 42 m&l for water proofing block boards 18 / 19 mm , grade 2 exterior quality grade , commercial type fixed with screws to timber frame work. complete all as specified and as directed by engr in charge. 43 m&l for 0.9 mm thick decorative choice of laminates type i of surface finishwhitestuck with importedadhesive on sides of board as directed by eng in charge . ( make corby, or euro ) 44 m&l prelaminated partical board 19 / 20mm medium density , prelaminated with one side with decorative choicelaqmination and other side balancingwith white laminationfixed with screws as in shelves to kitchen almirah and cub board fixed in repair.complete all as specified and as directed by engr in charge. 45 s&f 12mm thick plywwod grade bwr , type bb , fixed with screws to timber frame work.complete all as specified and as directed by engr in charge. 46 s&f 6mm thick plywwod grade bwr , type bb , fixed with screws to timber frame work.complete all as specified and as directed by engr in charge. 47 m&l for 0.9 mm thick decorative choice of laminationtype 1 of surface finish , colour and pattern as approved adhesive as per manufacturers instructions complete all as specified and as directed by engr in charge. 48 m&l for 1.50 mm thick pvc laminated decorative impressionchoice of laminationtype 1 of surface finish , colour and pattern as approved adhesive as per manufacturers instructions ( corby / duco ) . 49 s&f stain less steel catcherof superior quality complete all as specified and as directed by engr in charge. 50 s&f stain less steel pivoted type hingesof superior quality complete all as specified and as directed by engr in charge. 51 s&f 75mm long brass handle of desired finish with screws as approved by engg in charge. 52 s&f 35mm long mortice lockcomplete all as specified and as directed by engr in charge. ( make :godrej / harrison ) 53 s&f 75mm long brass tower bolt of desired finish with screws as approved by engg in charge. 54 s&f drawer side channel of std size and incl of rooler for moving drawer, mild steel bright finish, or electrogalavanised width of flap 30mm & length 60 mm all as specified. 55 s&f stainless steel fancy type, bright finish handles fixed with screw, of 125mm size all as specified. 56 s&f stainless steel multipurpose bracket in wooden / partitions for storing rations types made of 4mm dia stainless steel rods, fixed in side partition etccomplete.make: usha shriram enpt or equivalent ) . 57 s&f stainless steel luddel craddle hanging stand for cutlery all as specified and directed dy engr in charge.make: usha shriram enpt pvt ltd. 58 s&f stainless steelzero crank hinges fancy type ( with euro concealed hinges make: avis gold or equivalent ) fixed to shutter in cub board of std size and shape all asdirected dy engr in charge. 59 s&f 7s&f sinks made of stainless steel lmmthickkitchenorlaboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including fixing contilever brackets and connecting union to pipe complete all as specified and as directed by engr in charge. 60 m&l for recessed type stain less steelhandle for cup boards size 150 mm long complete all as specified and as directed by engr in charge. 61 m&l for roller ( pvc / stain less steel ) suiltable for sliding shutters . as app by eng in charge 62 pvc toilet cabinet with shelves and shutters fixed with looking mirror of size 600 x 450 mm complete all as specified and as directed by engr in charge. ( make : commander or equivalent ) 63 s&f continous ( piano ) hinges 30mm wide mild steel bright hinges 30 mm with flap, ms bright finished or electrogalvanised complete all as specified and as directed by engr in charge. 64 hasp and staple 100mm aluminium anodised, safety type, with mild steel hinges pin including bolt to hinge plate and fixed with screws complete all as specified and as directed by engr in charge. 65 s&f mild steel peg set stay 300 mm with and incl screws and bolts complete all as specified and as directed by engr in charge. 66 butt hings, 100 mm long, extructed aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type c 21.complete all as specified and as directed by engr in charge. 67 s&f butt hings, 100 mm long, extructedisi marked complete all as specified and directed by engr in chargefixed complete all as specified and as directed by engr in charge. 68 s&f extruded aluminium alloy handles, 100 mm long, fabricated type anodised complete all as specified and as directed by engr in charge. 69 s&f aluminium, anodised , 100 mm long, barrel tower bolts of extruded section and fixed complete all as specified and as directed by engr in charge. 70 s&f extruded aluminium alloy handles, 150 mm long, fabricated type anodised complete all as specified and as directed by engr in charge. 71 s&f aluminium, anodised , 150 mm long, barrel tower bolts of extruded section and fixed complete all as specified and as directed by engr in charge. 72 supply and fix floor door stopper of aluminium alloy body, overall length of cover plate 140 mm and tongue anodised with hard drawn steel sring fixed in floor complete all as specified and as directed by engr in charge. 73 s&f aluminium alloy, anodised, slidding door bolt300mm long, with hasp staple ( bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and as directed by engr in charge. 74 s&f mild steel, 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete fixed in repair complete all as specified and as directed by engr in charge. 75 s&f figured glass, pin head type, 4mm thick and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and as directed by engr in charge. 76 s&f 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not execeeding 0.5 sqm in each pane for metal frames complete all as specified. 77 s&f anodised aluminium with powder coating frame for doors, windows , ventilators with one or more rebates includirg joining cleat for fixing etc. complete all as specified and as directed. 78 s&f anodised aluminium frame for doors, windows , ventilators with one or more rebates includirg joining cleat for fixing etc. complete all as specified and as directed. 79 s&f sheet glass, ordinary quality 5.5 mm thick for aluminium door , window and vent.and glazing in square n exc 0.5 sq.m in each pane complete all as specified. 80 s&f neoprene / epdm rubber gasket for fixing sheet glass complete all as specified. 81 m & l pcc25 mm thick 1:2:4 type b0 ( 12.50 mm graded aggregate ) in any position in ground floor / roof complete all as specified and as directed by engr in charge. 82 m & l pcc75 mm thick 1:3:6 type b0 ( 12.50 mm graded aggregate ) in any position in ground floor / roof finishing cement concrete surface without using extra cement complete all as specified and as directed by engr in charge. 83 m & l pcc1:2:4 type b1 ( 20 mm graded aggregate ) as in hold fast blocks rungs etc icluding necessary form work complete all as per specified and directed ny engr in charge 84 m & l pcc 1:3:6 type c0 ( 12.50 mm graded aggregate ) as in filling in pressed steel frames complete all as specified and as directed by engr in charge. 85 m and l for coloured non skid ceramic tiles exceeding 0.11 sqm but not exceeding 0.18 sqm 7 to 8mm thick in floorsset and jointed in neat cement slurry and pointed incoloured cement to match the floorlaid over 15mm thick screed in cement mortar 1:6.complete all as specified and as directed by engr in charge. 86 m&l glazed ceremic tiles white450x300mmx7mm thickcoloured, set and jointed in neat cement slurry and pointed in white cement or coloured to match colour matching with floortiles as on vertical surfaces laid over 10mm thick cement screed in 1:4.complete all as specified and as directed by engr in charge. 87 m&l chequered cement concrete tiles 25 cm x 25 cmx25mm thick with grey cement and no pigment set jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed in cement and sand mortar 1:4 complete all as specified 88 m&l for vitrified tiles not exceeding 0.36 sqm 10 mm thick in floors set and jointed in neat cement slurry and pointed in neat cement s;urry in floors including 15 mm thick screed bed in cement and sand mortar 1:4 complete all as specified 89 m&l for vitrified tiles not exceeding 0.36 sqm 10 mm thick in floors set and jointed in neat cement slurry and pointed in neat cement s;urry in floors including 15 mm thick screed bed in cement and sand mortar 1:4 complete all as specified but in vertical surface. 90 m and l for 20mm thick granitemachine cutslab table rubbed and polished graniteas on cooking platforms incl. pointing in white cement 1:2using marble dustwith admixture of pigmentto match with marble shadelaid over 20mm thick cement screed in cement mortar 1:6.complete all as specified and as directed by engr in charge. 91 rendering 10 mm thick in cm 1:6 on other than fair faces of brick work or concrete surfacesfinished fair and even complete all as specified and as directed by engr in charge. 92 rendering 15 mm thick in cm 1:4 on fair faces of brick work or concrete surfacesfinished fair and even complete all as specified and as directed by engr in charge. 93 rendering 5mm thick on fair faces ofconc. surfaces in cement mortar 1:3, even and smooth w / o using extra cement as on ceiling.complete all as specified and as directed by engr in charge. 94 s&f tubes, medium grade galvanised, 15 mm borewith all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed by engr in charge. 95 s&f tubes, medium grade galvanised, 20 mm borewith all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed by engr in charge. 96 s&f aluminium sheeting 0.56 mm thick alloy 31000 h4 in ridges, hips, valley gutter drip and straight flashing ( length and girth as fixed ) complete all as specified and as directed by engr in charge. 97 s&f mild steel work as in hold fasts, clamps, bands, straps etc conforming to fe 410 0 complete all as specified and as directed by engr in charge. 98 s&f sinks with drainage board made of stainless steel 1mm thick kitchen or laboutery with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460mm bowl size 410 mm 330 mm x 160mm complete all as specified and as directed by engr in charge. 99 s&f stainless steel plate rack, tubular type, with fixing arrangement900mm x 900 mm size all as directed and as approved by engr in charge. 100 s & f glass corner of size 300mmx300mm with5.5 mm thick glass andsteelness steel clip and steelness steel railing allround the shelfcomplete all as specified and directed by engineer in charge . 101 s&f 600x450mm bevelled edge mirror of selected quality glass mounted on 6mm th ac building board or commercial ply complete all as specified and as directed by engr in charge. 102 s&f 5mm thick looking mirror of selected quality with and including stainless steel spacers any size as approved by engrbevelled edge mirror of selected quality glass mounted on 6mm th ac building board or commercial ply complete all as specified and as directed by engr in charge. 103 s&f pvc ( swr ) pipes 75 mm bore, single socketed, in any length with rubber ring jointed fixed to walls complete all as specified and as directed by engr in charge. 104 s&f pvc ( swr ) pipes 110mm bore, single socketed, in any length with rubber ring jointed fixed to walls.complete all as specified and as directed by engr in charge. 105 s&f pvc ( swr ) branch piece, single ( single y ) equal or unequal, 75mmbore.complete all as specified and as directed by engr in charge. 106 s&f pvc ( swr ) vent cowl 75 mm complete all as specified and as directed by engr in charge. 107 s&f pvc ( swr ) floor trap 75 mm, plain with grating including jointing with solvent cement complete all as specified and as directed by engr in charge. 108 s&f pvc ( swr ) branch piece, single ( single y ) equal or unequal 110mmbore.complete all as specified and as directed by engr in charge. 109 s&f pvc ( swr ) bends any radius 75mm bore complete all as specified and as directed by engr in charge. 110 s&f pvc ( swr ) bends any radius 110mm bore complete all as specified and as directed by engr in charge. 111 s&f pvc ( swr ) gully trap 125 / 110 mm setting and jointing with solvent cement complete all as specified and as directed by engr in charge. 112 s&f in repair stack clamp out of 40mm x3mm flat iron stays with rubber gasket covering including bolt and nuts, spacer and securing ends of stays to walls or roof for 50mm bore piece complete all as specified and as directed by engr in charge. 113 s&f in repair stack clamp out of 40mm x3mm flat iron stays with rubber gasket covering including bolt and nuts, spacer and securing ends of stays to walls or roof for 100mm bore piece complete all as specified and as directed by engr in charge. 114 disconnecting existing tanks, setting aside ( or lowering if required ) for repairs cleaning etc andhoisting if required reconnecting and refixing in position after cleaning and removing all scale and dirtetc from tanks and from mouths of circulating pipes etc complete ( capacity of tanksexc 250 ltr and n exc 500 ltrs ) complete all as specified and as directed by engr in charge. 115 s&f rotational moulded double layer ( isi marked of app make ) polythene water storage tank ( cylindrical vertical with closed top ) hoisted and fixed in position of 500 ltrs including dismantling existing.complete all as specified and as directed by engr in charge. 116 s&f ball valve high pressure of ptmt with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixedfixed in repair.of 20mm complete all as specified and as directed by engr in charge.make : prayag or equivalent. 117 s&f brass cp wall mixer non telephonic for mixing hot and cold water screwed down for iron pipe 15mm bore.complete all as specified and as directed by engr in charge. ( make : parryware or hindware or equivalent ) . 118 s&f brass cp whb mixer non telephonic for mixing hot and cold water screwed down for iron pipe 15mm bore complete all as specifie and as directed by engr in charge . ( make : parryware or hindware or equivalent ) . 119 s&f vitreous china wash down water closet pan with fixing bolts, trap ( pedestal pattern ) , white, ( excludingflushing cistern and flush pipe ) complete fixed in repairs complete all as specified and as directed by engr in charge. 120 supply and fix vitreous chinawash hand basin flat back size 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand etc complete fixed in repairs complete all as specified and as directed by engr in charge. 121 s & f pvc valveless ( syphon internal fitting ) of pvc low levelaction type flushing cistern, 10 ltr capacity low level , whitewith inlet, ball valve, float and handle including brackets fixed in repairs complete all as specified and as directed by engr in charge. 122 s & f pvc valveless syphonic action type flushing cistern, 10 ltr capacity low level , whitewith inlet, ball valve, float and handle including brackets fixed in repairs.complete all as specified and as directed by engr in charge. 123 s&f pvc connections 15 mm size with ptmt nuts of length 450 mm complete all as specified and as directed by engr in charge. 124 s&f stainless steel tubular towel rail, 200 mm dia d type 60cm long between flanges complete all as specified and as directed by engr in charge. 125 s&f bib tap 15 mm dia, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwedfor iron pipeand fixed in repairs complete all as specified and as directed by engr in charge. ( make : parryware or hindware or equivalent ) 126 s&f bib tap 15 mm dia, long body fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwedfor iron pipeand fixed in repairs complete all as specified and as directed by engr in charge. ( make : parryware or hindware or equivalent ) 127 s&f stop valve, 15 mm dia, fancy type, chromium plated, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repairs complete all as specified and as directed by engr in charge. 128 s&f stop valve, 15 mm dia, concealed stop valvefancy type, chromium plated, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repairs complete all as specified and as directed by engr in charge. 129 s&f pillar taps, 15mm dia, fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, long screwed shanks and fly nuts, screwed for iron pipe and fixed in repairs.complete all as specified and as directed by engr in charge.make: jaquar or equivalent 130 s&f brass chromium plated shower rose 125 mm size including fixing to steel pipe or union fixed in repairs complete all as specified and as directed by engr in charge.make: jaquar or equivalent 131 sf brass chromium plated shower arm 15 mm 195 mm long with bend 45 degreemm size including fixing to steel pipe or union fixed in repairs complete all as specified and as directed by engr in charge.make: jaquar or equivalent 132 s&f sheet glass shelf assembly in repair , oconsisting of 5.5 mm thick sheet glass shelf 12 cm wide chromium plated bracket guard and railing 60 cm long complete all as specified. 133 s&f plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by engr in charge. 134 s&f cp health faucetfixed type suitable for ewcs with 1, 5 mtr stainless steel tube complete all as specified and directed by engineer in charge make : jaquar, prayag 135 s&f cp toilet paper holder fancy type complete all as specified and directed by engineer in charge.make: jaquar or equivalent 136 s&f angle valve cast copper alloy fancy type cp with long shank and cup and screwed for iron pipefixed in repair complete all as specified and as directed by engr in charge.make: jaquar or equivalent 137 s&f waste pipe 32mm for whb with coupling fixed in repairs complete all as specified and as directed by engr in charge. 138 m&l for along the wall below concrete or masonry using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed by engr in charge. 139 m&l for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 ( 1 cement: 2 coarse sand ) to match the existing floors complete all as specified and as directed by engr in charge. 140 s&f grating doom 125 mm dia with waste hole of ptmt ( minimum weight 40 gms ) complete all as specified and as directed by engr in charge. 141 s&f chromium plated soap dish complete all as specified and directed by engineer in charge. 142 s&f aluminium snake bead with bush duly fitted with screws with length equal to door width as specified and directed by engr in charge 143 m&l for repairingof rolling shutters making functional by providing greasing oiling , welding etc.including taking down rolling shutters or hood if required complete all as specified and as directed. 144 s&f safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed by engr in charge. 145 s&f ball bearing for rolling shutters.complete all as specified and as directed by engr in charge. 146 m&l for 25mm to 30mm thick plaster of paris ( pop ) ( gypsum anyhydrous ) raised moulding to flat surface of ceiling including preparation of surfaces all as directed.complete all as specified and as directed by engr in charge. 147 m&l for green sheet pvc of best quality to cover the surface where required complete all as specified and as directed. 148 s&f water closet pedestral pattern white or coloured ( as approved by engr in charge ) make :cera cat no.s1013113 ( cristy single piece suite p or s trap incl seat cover ) or equivalent in hindware , jaquar, parryware ) complete all as specified and as directed. 149 s&f in aluminium composite panel of any colour of having thickness of approx 3 4mm thick which are used in aluminium doors / partitions of all as specified and as directed. 150 s&f in pre laminated pvc boards of heat and fire resistant , non toxic , anti chemicaland corrosion resistant, termite proof and resistant to fungal attacks used in kitdhen cabinets of any finish complete all as specified and as directed. 151 m&l washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 ( 1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per square metre, top layer 15mm cement plaster 1:1 / 2:2 ( 1 cement: 1 / 2 coarse sand : 2 stone chipping 10mm nominal size ) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified ( paymentfor providing grooves shall be made separately ) . 152 s&f 10.00 mm thick gypsum boards as in ceiling as per approved desidg including recessing for provision of ceiling lights , moisture resistant , incl intermediate , perimeter channel ceiling channel , alon nuts and bolts connecting plates gypsum boards , dry wall screws soffits cleats , ceiling section, rowel plugs fixtures and screws complete all as spfd and as shown in sketch and applying twwo coats of emulsion paint over a coat primer on exposed surfaces.design of ceiling board as app by engr in charge. ( note: no extra payment shall be claimed from contractor for designs to ceiling falls etc ad shall be measured in plan only ) 153 m&l for 1.5mm thick self adhesive waterproofing membrane consisting of self adhesive sbs ( styrene butadiene styrene ) modified / bitumen compound covered on the top side with high density cross laminated polyethylene film and on the underside with an easy to peel silicon film all as per manufacturer’s instructions having minimum overlaps 50mm on sides and 100mm on ends, provided with & including suitable bitumen primer @ 0.30 litre per sqm as recommended by membrane manufacturer after cleaning the roof surface / sunken floor from all loose, dust, dirt, foreign material and particularly oil and grease marks, complete all as specified and as directed.make : m / s texsa india ltd / m / s pidilite industries ltd / m / s sika india pvt ltd / m / s stp limitednote : the net area of waterproofing treatment shall be measured and paid for without any extra allowance for side & end laps for membrane and this aspect shall be deemed included in the quoted rates. 154 taking down carefully ( aluminium ) point wiring complete of any type ( batten / surface conduit or concealed ) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper / white washing / colour washing to match with the existing surface complete all as spcified and directed. 155 taking down submain wiring aluminium / copper of any size including earth continuity condutor on teak wood or conduit and removing from site and making good the disturbed surface of wall etc complete all as specified and directed. 156 taking down old u / s existingdb tpn 4 way anddb spn 12 way including mcb / mccb of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed. 157 m & l for point wiring with and including single core frlsh pvc insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm 1100 volts grade drawn through and including suitable size of pvc concealed conduit with accessorieswithlaminated top cover fixed on ms sunken box for housing of switch, socket, regulator etc complete with and including 1.5 sqmmfrlsh pvc insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete all as specified and as directed by engr in charge for the following : ( a ) one light / fan / ex fan / bell / point controlled by one switch. 158 ( b ) one pin 5 amps socket point on the same board with other switches complete 159 ( c ) one 3 pin 5 amps socket on independent board. 160 ( d ) all as per item no 4 above but but one light point controlled by two 02 way switchboard complete and all as directed by engr in charge. 161 ditto all as per item no 157 above but with 4.0 sqmm copper wire for 3 pin socket outlet 20 amp on independent board complete and all as directed by engr in charge. 162 s&f switch piano type, 5 amp, single pole one way, 230 volts, flush type complete all as specified and as directed by engr in charge. 163 s&f switch piano flush type single pole, one way 15 / 20 amps 230 voltscomplete all as specified & directed by engr in charge. 164 m&l socket outlet 3 pin5 amps flush type230 voltscomplete all as specified and directed by engr in charge. 165 m&l for socket outlet 2 in 1, 3 pin, 5 & 15 amps, 230 volts t complete all as specified & directed by engr in charge. 166 s&f ceiling rose, surface backelite , three terminal ac, 230 voltcomplete all as specified. 167 supply and fixing led mirror light fitting , type with high out put diffuser 2 feet, 5watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete.havells cat part no enduralinearneobs10wled865spcwh / wipro cat part no ll20 111 xxx 65ne3 / bclsb 10 wh 168 s&f led tube light fitting, 1x 20 22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24 / 0.20 sqmm complete all as specified and directed by engr in charge. make :philips bn021 led 20s psu cw gr s2 / crompton greaves lddr20 cdl dazzle ray / bajaj bclab 20w 169 s&f single pole and neutralenclosure with a two pin and earth plug and socket complete with one single pole mcb 20 amp complete all as specified and as directed by engineer in charge. 170 supply and fixing fan regulator electronicsocket typefive step controlled 230v ac 50 hz forcomplete all as specified and directed by engr in charge. 171 s&f sheet metal enclosure mcb db, double door, tpn 4 way with 200 amps rated busbar all as specified and as directed. make: hegar / legrand / seimens 172 s & f double door, sheet metal enclosure, powder coated for mcb db spn 12 way fittedwith neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to is 13032 1991 complete all as specified and as directed by engr in charge. 173 s & f mcb sp, 5 32 amps , 240 volts, breaking capacity 10ka complete all as specified and as dircted by engr in charge. 174 s&f mcb 63amps, c curve tpn, 415 volts, complete all as specified and as directed by engr in charge. 175 supply and fixing bell push, flush type, 5 amp 230v ac 50 hz forcomplete all as specified and directed by engr in charge. 176 supply and fixing buzzer, ding dong ac. 230 volts, single pole complete all as specified and directed by engr in charge. 177 m & l lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by engr in charge. 178 taking dowen and refixing led light fitting mirror type with high out put diffuser 2 feet, 10 / 5 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size complete. 179 taking dowen and refixingled tube light fitting, 1x 20 22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24 / 0.20 sqmm complete all as specified and directed by engr in charge. 180 s&f mccb 100 amps, 4 pole, 415 volts, fixed type breaking capacity 16ka complete all as specified and as directed by engr in charge. 181 s&f mccb 40 amps, 4 pole, 415 volts, fixed type breaking capacity 16ka complete all as specified and as directed by engr in charge. 182 s&f in replacement decorative wall light fittings complete made up of polycarbonate, including withfor 9 w led lamp complete all as specified and directed by engr in charge. make / sample approved by engr in charge : surya / havells / phillips 183 s&f in replacement bad side light fitting with suitable led bulb complete all as specified and directed by engr in charge. sample approved by engr in charge and ge . 184 s & f led light fitting 1x9w / 1x10wbulkhead luminaires including led light driver holder connecting up with three core flexible copper conductor cable of suitable size. 185 s&f switch piano single pole 5 amps, two way, complete all as specified and as directed by engineer in charge 186 supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230v, 50 hz, rpm 1200, copper winding of sweep 300m 187 m & l for submain ( single phase ) wiring complete with and including 10 sqmm two single core, ( frlsh ) fire retardant, pvc insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, drawn through existing pvc conduitincluding accessories and fixed on walls and10sqmm, fire retardant, pvc insulated, multistranded copper conductor cable for earthing and connected to common earth dolly complete all as specified and as directed by engr in charge. note : ( i ) two runs of10.0 sqmm pvc insulated wire and one run of 10sqmm wire and one run of pvc conduit shall be measured as one unit length. 188 m & l for submain ( single phase ) wiring complete with and including 4.0 sqmm two single core, ( frlsh ) fire retardant, pvc insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, drawn through pvc conduit of suitable size including accessories and fixed on walls and 4 sqmm, fire retardant, pvc insulated, multistranded copper conductor cable for earthing and connected to common earth dolly complete all as specified and as directed by engr in charge. note : ( i ) two runs of 4.0 sqmm pvc insulated wire and one run of 4 sqmm wire and one run of pvc conduit shall be measured as one unit length. 189 s & f mcb spn, 5 32 amps, 240 volts, breaking capacity 16ka complete all as specified and as dircted by engr in charge. 190 m&l for submain wiringusing 4 runs of single core frls pvc insulated, unsheathed stranded copper conductor cable of size 4runs of 10 sqmm of voltage rating 1100v for three phase & neutral, drawn in and including concealed pvc conduit of dia not less than 25 mm dia with standard acessories, along with two run of frls pvc insulated, unsheathed, stranded copper conductor of size 2x6.0 sqmm as earth continuity conductor all as specified and directed ( note 4 runs of single core frls pvc cable 10sqmm for three phase & neutral with two run of earth conductor as earth and conduit shall be measured as one unit ) ...
42
Public Works Department - Rajasthan
36822515 white wash and colour washing work in bajaj nagar qtrs. under sub dn. gandhi nagar iii jaipur ( 123 / secity / cd iii / 2216 mtc rep / 09 / 2022 23 ) ...
43
Department Of Local Bodies - Rajasthan
36536464 painting white wash road repair and any other works at various places in city vidhan shabha ward 25 se 43...
44
Public Works Department - Rajasthan
36318476 remaining work of white wash and steel railing in circuit house, pali...
45
Department Of Defence - Rajasthan
36150222 bids are invited for computer table , white board , wall clock , power change liver , printer cartridge lexmark 58d 3000 , dry colour , paint , white wash , large enevelope yellow , a4 envelopes , brown envelopes , do envelope , stapler pin 10nos , yellow dusting cloth , refill reynold pen , add gel pen , refill add gel pen , pilot pen ink , sketch pen black mse total quantity : 281...
46
Military Engineer Services - Rajasthan
36109207 repair and maintenance of internal electrification with fitting and fixture of otm zone f at mil station sri ganganagar, 1 taking down carefully aluminium point wiring ( light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in cm 1:3 etc complete all as specified and directed by engineer in charge. 2 m & lfor concealed conduit point wiring complete for light on independent / combine boardwith cable 1.5 sqmm ( nominal area ) frlsh pvc insulated multistranded unsheathed copper conductor, drawn in and includingpvc concealed conduitpipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , aftercutting in wall chasing for conduits and sinkings for sunkencast iron / pressed steelterminal boxes 60mm deep , suitable lengthand 1.20 mm thickness for mounting, switches, sockets, fan regulatorwith 3 mm thick plastic laminated sheet cover fixedwith brass screwed and cup washers, dulygrouting and painted with red oxide metal primer and making the gooddisturbed surfaces of wallin cm 1:3 with white wash or existing colour including provision ofcontinuousearth continuity conductoralong with point wiring of 1.5 sqmm copper pvc insulated cable for one light / fan point controlled by one switchand connected to commonearth dolly, complete all as specified anddirecedby the engineer in charge. 3 all as per srl item no 02 here in before but for one switch socket combination 5 / 6 amp on independent board complete all as specified and directed by engineer in charge. 4 all as per srl item no 02 here in before but for one three pin socket outlet 5 amp on same board with other switches complete all as specified and directed by engineer in charge. 5 all as per srl item no. 2 here in before but for one switch socket combinationt 6 pin 5 / 15 amps on independent board with copper conductor 2.5 sqmm complete all as specified and directed by engineer in charge. 6 all as srl item no. 02 here in before but for one light point controlled by two 2 ways switches complete all as specified and directed by engineer in charge. 7 all as per srl item no. 2 here in before but for call bell point complete all as specified and directed by engineer in charge. 8 m & lfor concealed existingconduit point wiring complete for light / fan on independent / combine boardwith cable 1.5 sqmm ( nominal area ) frlsh pvc insulated multistranded unsheathed copper conductor, drawn inpvc existing concealed conduitpipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , and sinkings for new sunkencast iron / pressed steelterminal boxes 60mm deep , switches, sockets, fan regulatorwith 3 mm thick plastic laminated sheet cover fixedwith brass screwed and cup washers, dulygrouting and painted with red oxide metal primerincluding provision ofcontinuousearth continuity conductoralong with point wiring of 1.5 sqmm copper pvc insulated cable for one light / fan point controlled by one switchand connected to commonearth dolly, complete all as specified anddirecedby the engineer in charge. 9 all as per srl item no 08 here in before but for one switch socket combination 5 / 6 amps on independent board complete all as specified and directed by engineer in charge. 10 all as per srl item no 08 here in before but for one three pin socket outlet 5 amp on same board with other switches complete all as specified and directed by engineer in charge. 11 all as per srl item no. 8 here in before but for one socket outlet 3 pin 15 amps on independent board with 2.5 sqmm copper cable complete all as specified and directed by engineer in charge. 12 all as per srl item no. 8 here in before but for one light point controlled by two 2 ways switches complete all as specified and directed by engineer in charge. 13 all as per srl item no. 8 here in before but for call bell point complete all as specified and directed by engineer in charge. 14 s & f switch piano flush type 5 / 6 amps single pole one way complete all as specified and directed by engineer in charge. 15 s & f switch piano flush type 5 / 6 amps single pole two ways complete all as specified and directed by engineer – in charge. 16 s&f bell push flush type 5 amp complete all as specified and directed by engineer – in charge. ) 17 s&f electronic bell ac 230 volt single pole ding dong type complete all as specified and directed by engineer in charge. 18 s & f switch socket combination 5 pin, type 5 / 6 amps flush type complete all as specified and directed by engineer in charge. 19 s & f switch socket combination 6 pin, 15 / 16 amps flush type complete all as specified and directed by engineer in charge. 20 s & f socket outlet 5 pin 5 amps flush type complete all as specified and directed by engineer in charge. 21 s & f in replacement industrial socket metal clad plug and socket with mcbs single pole 20 amp complteall as specified and directed by engineer in charge. 22 s & f in replacement modular switch5 / 6 amps single pole one way, one module complete all as specified and directed by engineer in charge. 23 s & f in replacement modular switch socket combination 5 pin, type 5 / 6 amps5 in 1flush type including modular cover plate with frame complete all as specified and directed by engineer in charge. 24 s & f in replacement modular switch socket combination 6 pin, 5 / 16 amps flush type including modular cover plate with framecomplete all as specified and directed by engineer in charge. 25 s & f in replacement modular switch5 / 6 amps single pole two ways complete all as specified and directed by engineer – in charge. 26 s & f in replacement modular socket outlet 5 pin 5 amps flush type complete all as specified and directed by engineer in charge. 27 s&f in replacement modular bell push 5 amp complete all as specified and directed by engineer – in charge. 28 s & f in replacementmodular stepped type, fan regulator not less than 120 watt for ceiling fan 1200 / 1400mm sweep complete all as specified and directed by engineer in charge 29 s & f ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified and directed by engineer in charge. 30 s & f in replacement of existing light fitting withled batten with aliminium housing andintegrated electronic driver, 20 / 22 watt having input voltage ac90 300v, 50 hz , 6500k, and all other accessories including connection with flexiblecable copper conductortwin coreof size 23 / .2 mm upto ceiling rose / connectorcomplete all as specified and directed by engineer in charge. ( make:havells cat part no: lumilineplusbs20wled865spcss, bajaj cat part no.: bclsbal 20w cw , philips cat part no. bn021c led22s psu cw gr 31 s&fin replacement security light fitting led type 25 watt with all necessary acessories, clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 hz ac & supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23 / 0.0076 complete all as specified and directed by engineer in charge ( make:havells cat part no: endurapearlsl25wled757sasytopcmp, bajaj cat part no. brlep 25w led wh, philips catpart no. brp042pled25cwslepsugr dx ) 32 s & fin replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed by engineer in charge. 33 s & f water tight bulk head fitting, comprising of connector galvanised cast iron back plate, weather proof enameled gallery , with electronic driver, ( latest design ) , 10 w , upper pvc body all as specified and directed by engineer in charge ( make:havells cat part no : hexaft10wled857ssymbopc, bajaj cat part no. bibwp 10w led, crompton cat part no. lbhp 10 cdl ) 34 s&fin replacement decorative wall light, brushed nickle finish fiturewith opal glass diffuser including 4 watt led filament lamp e14 base complete all as specified and directed by engineer in charge ( make havells cat part no: lhfoaic1tz1i040or equivalent make in bajaj, crompton 35 supply and fixing led light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexible copper conductor cable of suitable size all as specified and directed by engr in charge. ( make : havells cat part no lumilineplusbs10wled865spcss, bajaj cat part no. bclsb 10 wh, philips cat part no. bn021 led12s 6500 psu gr ) 36 s & f speed regulator for ceiling fan 1200 / 1400mm sweepcomplete all as specified and directed by engineer in charge 37 s&f in replacementrecess mounting 2 x 2 feet 36 watt led luminaire with powder coated crca housing with leds, seamless front frame with high transmission acrylic cover and fixed electronic driver ( surge protector ) complete all as specified and directed by engineer in charge.make:crompton cat part no :lctlrne 36 fo cdl or equivalent make in havells, bajaj 38 s & f in replacement round / square recess mounted led edge lit slim downlight 12 wattwith die cast aluminum housing finished in premium white powder coating. efficacy 100lm / w complete all as specified and directed by engineer in charge.make havells cat part no.edgeprorddlr12wled857s, bajaj cat part no. bpslr 12w wh, crompton cat part no. lscrm 12w cdl 39 supply and fix in replacement led flood light 80watt , protected to ip65 with flat front toughened glass and fixed electronic driver ( surge protecter ) complete including fixing arrangments in ground / on pole complete all as specified and directed by engineer in charge .make havells cat part no. baybriteflare80wled857pwbbolt g, bajaj cat part no.bjfl 80w led i, crompton cat part no. lfl 80 cdl / 60 m 40 supply and fix in replacement ledhighbay luminaire 80w having fin ventilation technology for better thermal management and its cutting edge led technology seeks to various industrial applicaton complete all as specified and directed by engineer in charge . make: havells cat part no. iliosbayplushbp80wled857sp90dtopc, bajaj cat part no. bghb 80w led g v, crompton cat part no. lhb11 80 cdl / 60 m 41 supply & fixing in replacementled land scape light / bollard light 10w / 9 w with 900mm height extruded aluminium cylindrical section housing ip 65 rated complete with base & log bolt grafite grey epoxy cationic powder coated all accessories all as specified. and directed by engineer in charge . make: crompton cat part no lblsr 10 ww, bajaj cat part no bgbom 650 9w led or equivalent make in havells. 42 s & f in replacement ledsuspension light fitting 36 w ( fixture size : ( lxwxh ) in 1136x54x74 mm ) , aluminum extruded direct indirect light effect gives homogenous light distribution effect & enhances the visual comfort with joining kitaccessoriesand connecting to mains cable complete all as specified and directed by engineer in charge. ( make : havells cat part no. destellodilp36wled857spmmawh, crompton cat part no. lclp54 36 cdlor equivalent make in bajaj 43 supply and fixing in replacement post top lantern led type60 / 70 watt including fixing arrangments on 76 mm dia gipipe on main gate pillers 230 watt volts ac outdoor type with decorative post top for 360 degree indirect light ip 65 protection with impact and corrosion resistant complete with driver and lamp complete.complete all as specified and directed by engineer in charge. ( make : havells cat part no. coralmaxipt70wled830psymtopc, crompton cat part no. lpto 60 cdl m or equivalent make in philips ) 44 s&f led lamp 9w, white / red / yellow / blue / green color for angle holder complete all as specified and directed by engineer in charge. 45 s & f in replacement of sub main wiring with two single core cables pvc insulated and un sheathed 6 sqmm ( nominal area ) frlsh stranded copper conductor drawn inexistingpvc conduitincluding 6.00 sq mm ( nominal area ) copper cableas earthcontinuity conductor including necessary connections, pvcflexible pipes are used in pannel board while connecting the cablecomplete all as specified and directed by engineer in charge. ( note : pvc cable and pvc conduit shall be isi marked ) 46 s & f in replacement of sub main wiring with two single core cables pvc insulated and un sheathed 4 sqmm ( nominal area ) frlsh stranded copper conductor drawn inexistingpvc conduitincluding 4.00 sq mm ( nominal area ) copper cableas earthcontinuity conductor including necessary connections, pvcflexible pipes are used in pannel board while connecting the cablecomplete all as specified and directed by engineer in charge. ( note : pvc cable and pvc conduit shall be isi marked ) 47 s & f in replacement sheet metal enclosure for double door db made out of crca mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted sp & n 8 ways, 240 volts, isi marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation mcbs and isolators etc complete all as specified and directed by engineer in charge. 48 s & f in replacement sheet metal enclosure for double door db made out of crca mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted sp & n 12 ways, 240 volts, isi marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation mcbs and isolators etc complete all as specified and directed by engineer in charge. 49 s & f in replacement mcb ‘b’ series type suitable for 240 volts, ac supply5 to 40 amps, s p & n with over load and short circuit protection and rupturing capacity not less than 10ka complete all as specified and directed by engineer in charge. 50 s & f in replacementmcb ‘b’ series type suitable for 240 volts, ac supply5 to 40 amps , single pole with over load and short circuit protection and rupturing capacity not less than 10ka complete all as specified and directed by engineer in charge. 51 s&f in replacement sheet metal enclouser for doble door vertical dbs made out of crca mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting vtpn 4 way 415 voltisi marked 250amps busbar stove enameled dust and vermin proof, ip:43 protection suitable for incorporation fp mccb ( v tech ) n1 frame upto 125a, isolators and including give connection with wire and cable etc complete all as specified and directedby engineer in charge 52 s&f in replacement mccb 4 pole63 amps with breaking capcity 16ka , fixed tm and 415 volts ac supply isi marked complete all as specified and directed by engineer in charge. 53 s&f in replacement mccb 4 pole 40 amps with breaking capcity 16ka , fixed tm and 415 volts ac supply isi marked complete all as specified and directed by engineer in charge. 54 s&f in replacement mccb 4 pole 100 amps with breaking capcity 16ka , fixed tm and 415 volts ac supply isi marked complete all as specified and directed by engineer in charge. 55 m & l for earthing complete with gi earth plate electrode 60 cm x 60 cm x 6 mmthick burried directly in ground ( earth pit not less than 2.25 mtr deep below ground level ) with top edge of plate not less than 1.5 mtr below ground level , connecting to gi earth lead 4 mm dia gi earth wire , by means of bolts, nuts and washers of giand protection by provisionof gi medium grade pipe 15 mm bore including provision of concrete pit in pcc ( 1:2:4 ) type b1 using 20 mm grade stone aggregate with 40 mm thick cover of rcc ( 1:2:4 ) reinforced with xpm ( weight not less than 4 gs / sqmm ) and frame of angle iron 25mmx25mmx6mm with lugs 02 nos and with 6 mm dia ms bar handle made to shape , gi light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmx 8 mm fi with fixing arrangement , funnel, wire mesh and earth work inhard dense soil , returning filling in and removal of surplus soil to a distance not exceeding50 mtrs all as per electric plate no.3 of ssr part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on complete all as specified and directed by engr in charge 56 excavation in trenches not exceeding 1.5 mtr wide and not ecxceedinf 1.5 mtr depth for laying of cablescomplete all as direted by engr in charge 57 returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm complete all as direted by engr in charge 58 removal of excavated material n exceeding 50 mtr and depositing where complete all as direted by engr in charge 59 supply and filling in sand for cable protection complete all as direted by engr in charge 60 supplying and laying un reinforced precast concrete cable cover, class lv, type 1 flat, size 250x 150mm x 40mm complete all as direted by engr in charge 61 s & f 1100 volts grade heavy duty cable pvc insulated aluminium conductor, served with inner sheathing of pvc tape and overall pvc sheathed in service connection suspended by insulating hanger not more than 1 meter apart including 4 mm suspension wire, one twin core cable flat or circular 4 sqmm, complete all as specified and directed by engineer in charge. 62 supply and lay in replacement jointing and testing and commissioning in replacement of 10 sqmm x2core xlpe insulated, screened , pvc bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & pvc sheathed lt cable 1100 v grade conforming to is 7098 laid in trenches / ducts / fixed on poles wall / laid under roads / paths / drain / culverts or passing through pipes complete all as specified and directed by engineer in charge. 63 supply and lay in replacement jointing and testing and commissioning in replacement of 25 sqmm x4 core xlpe insulated, screened , pvc bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & pvc sheathed lt cable 1100 v grade conforming to is 7098 laid in trenches / ducts / fixed on poles wall / laid under roads / paths / drain / culverts or passing through pipes complete all as specified and directed by engineer in charge. 64 m & l for air termination, single pointed, aluminium rod 12 mm dia and 300 mm long complete all as specified and directed by engineer in charge. 65 m & l for providing test point terminal block, made out of gun metal or phosphors bronze, of size 75 mm x 75 mm x 25 mm drilled and screwed including 03 nos 8 mm dia, 25 mm long hexagonal head screws complete all as specified and directed by engineer in charge. 66 m & l for aluminium strip 25 mm x 3.15 mm with saddles and fixing screws etc as in roof conductors and down conductor above ground complete all as specified and directed by engineer in charge. 67 m & l for gi strip 32 mm x 6 mm buried in ground complete all as specified and directed by engineer in charge. 68 m & l for earthing complete with gi earth plate electrode 60 cm x 60 cm x 6 mmthick burried directly in ground ( earth pit not less than 2.25 mtr deep below ground level ) with top edge of plate not less than 1.5 mtr below ground level , connecting to gi strip 32 x 6 mm as earthing lead , by means of bolts, nuts and washers of giand protection by provisionof gi medium grade pipe 50 mm bore including provision of concrete pit in pcc ( 1:2:4 ) type b1 using 20 mm grade stone aggregate with 40 mm thick cover of rcc ( 1:2:4 ) reinforced with xpm ( weight not less than 4 gs / sqmm ) and frame of angle iron 25mmx25mmx6mm with lugs 02 nos and with 6 mm dia ms bar handle made to shape , gi light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmx 8 mm fi with fixing arrangement , funnel, wire mesh and earth work inhard dense soil , returning filling in and removal of surplus soil to a distance not exceeding50 mtrs all as per electric plate no.3 of ssr part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on complete all as specified and directed by engr in charge 69 m & l for gi water tubing, light grade, 50 mm, 1.2 m long duly threaded on one side in and including fixing of gi socket for fixing of air termination and including fi clamp of 50 x 6 mm bend to shape for fixing of gi pipe post and fixed to wall ( gi pipe 1.2 m will be in single length and no joint will be allowed ) complete all as specified and directed by engr in charge 70 supply only 16 amp 3 pintop plug 240 volt, non flamablecomplete all as direted by engr in charge. havells ahlgxxw163 pk1 71 supply only 6 amp 3 pintop plug 240 volt, non flamablecomplete all as direted by engr in charge. havells 72 s&f exhaust fan made of sturdy engineering plastic of 250mmsweep , 240 volt, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core pvc insulated pvcsheathed copper conductorflexible cable 24 / 0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar ( 1 :4 ) white washing matching with existing colour etc. complete all as direted by engr in charge. 73 s&fmetal body exhaust fan 300 mmsweep, 900rpm, 230 volt, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core pvc insulated pvcsheathed copper conductorflexible cable 24 / 0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar ( 1 :4 ) white washing matching with existing colour etc. complete all as direted by engr in charge. 74 note : ( i ) amount ofcreditfor retrieved materials is mentionedin sch a section ii of tender documents in pdf form which will be deducted while acceptance of tender offline. ( ii ) contractor will furnish the performance warranty certificate along with name of dealer from the manufacturer for a specified period as recmmended by the companyfor the equipments mentioned againstrespective items. ( iii ) all led lights should be marked with ge sgnr and date of fixing. ( iv ) the contracotr will liable for penalty of rs 500 / day if he fail to interain the complaint given to him on next day...
47
Department Of Local Bodies - Rajasthan
36052672 painting white wash road repair and other necessary work at various places in city zone ward 25 to 43...
48
Public Works Department - Rajasthan
35898927 barricading work on banswara side causeway (both side), white wash and other work at beneshwar dham for beneshwar fair in block ghatol...
49
Military Engineer Services - Rajasthan
35811567 tender for repair maintenance of stps of age e / m under jaipur mil stn cleaning of treated water undergroud water storage sump of capacity 50, 000 gln at stp 1, 2, 3, 4 & 5 by specialized water tank clean tank cleanprocess as under : note 1 : all workers will wear mask and carry all necessary t&p for protection and smooth working before start cleaning process. the contractor will take prior permission from engineer in charge in written before starting work and will brief all aspect i.e date and time of cleaning start and completion so that suitable arrangment may be made to supply water during cleaning process. contractor will depute manpower in such manner that water supply time do not hamper. ( a ) mechanized dewatering and scrubbing the surface of floor and wall till removal of dirt, sendiments, fungus and the stains and cleaning, removal of sludge and shifting as directed. ( b ) high pressure cleaning. ( c ) soak the dirt and sendiments by vacuum cleaning. ( d ) anti bacterial spray on all dimensions inside tank. ( e ) m&l for marking date of cleaning on tank by using synthetic enemal paint, font design and letter size will be as directed by engineer in charge. ( 2 ) sludge / dirt and other sand debries etc will thrown out to place as directed by engineer in charge. ( 3 ) each stp shall be measured and paid as one job, if contractor failed / delayed after intimation for cleaning of each plant, penalty @ 20000 / shall be recoverd from his dues and contractors claim on this account shall not be entertained. 2 removing silt ( mud ) from sewage pump wellat stp 1, 2, 4&5 ( depth 7.5 meter, dia 8.5 meter ) and cleaning the bottom portion and sides of pump well by using man power at equal intervel of 6 months from date of commencement of contract, proper cleaning of sewage tank by following method complete all as mentioned in item no 3. 3 removing silt ( mud ) from sewage pump wellat stp 3 queens road ( size depth 7.5 meter, dia 3.5 meter covered with rcc roof and wall ) and cleaning the bottom portion and sides of pump well by using man power at equal intervel of 6 months from date of commencement of contract, proper cleaning of sewage tank by following method complete all as mentioned below: note for item no 2 and 3 : ( a ) all workers should be experienced for sewage pump well cleaning and necessary safety equipments including mask and other t&p for workers should be arranged by contractor before start cleaning process. ( b ) the contractor will take prior permission from engineer in charge in written before starting work and will brief all aspect i.e. date and time of cleaning start and completion so that suitable arrangement may be made. contractor will supply t&p and manpower in such manner that cleaning should be done without hampering sewage system.note ( 1 ) sludge / dirt and other sand debries etc will thrown out to place as directed by engineer in charge. ( 2 ) if contractor failed / delayed after intimation for cleaning of each plant, penalty@ rs 30000 / shall be recoverd from his dues and contractor s claim on this account shall not be entertained. 4 proper cleaning of rcc stilling chamber, rcc fine bar screen i&ii, rcc grit chamber i&ii, rcc oil and grease chamber, equalization tank, mbbr tank i&ii, flocculator, tube settler, cct, rcc filter feed tank, rcc slurry / sludge sump by experienced workers with safety equipments and t&p items required for cleaning of all above said parts of sewage treatment plant of 05 nos at equal intervel of 01month from date of commencement of contract complete all as mentioned below: ( a ) by mechanised dewatering and scrubbing the surface of floor, wall till removal of dirt, sediments and cleaning sludge removal and shifting as directed. ( b ) the contractor will take prior permission from engineer in charge in written before starting work and will brief all aspect i.e. date and time of cleaning start and completion so that suitable arrangement may be made. contractor will supply t&p and manpower in such manner that cleaning should be done without hamper sewage system.note ( 1 ) sludge / dirt and other sand debries etc will thrown out to place as directed by engineer in charge. ( 2 ) if contractor failed / delayed after intimation for cleaning of each plant, penalty @ rs 35000 / shall be recoverd from his dues and contractor s claim on this account shall not be entertained. 5 m&l for rectification of leakage from 50mm hdpe bore pipe line by cutting & replacement of defective hdpe pipe and refixing the same after cleaning and by connecting with old line with and including necessary fittings hdpe welding ( hot plate welding ) for old & new pipe includingnecessary exacavation & earth work as required complete all as specfied and directed . 6 all as per item no. 05 but for 100mm hdpe bore pipe 7 all as per item no. 05 but for 150mm hdpe bore pipe 8 all as per item no. 05 but for 250mm hdpe bore pipe 9 dismentling of centrifugal / monoblock pump set after disconnecting from power mains & pipe line of capacity 5 hp, 3 phase, 415 volts 50 hz, acof make kirloskar fromfoundation and dismantlingfor overhauling repairincludingreplacementof unservicablepart oiling , greasing, reinstalling and connecting with suction / dischargeline with correctalignment by replacing glandstuds and making completeelectricconnection includingtesting complete all as specifiedand directed. ( note spare parts required for replacement shall be measured and paid separetaly under respective items ) 10 transportation of motor to contractors work shop and back to site after repair, cutting of burnt winding & rewinding the stator with super enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles ete as per relevent is standard / manufacturers recommendation as directed by eic. 11 supply only stainless steel pump shaft as per existing make. 12 supply only gun metal impeller with neck key, distance bush as per existing make. 13 supply only ball bearing as per existing number and as per existing make. 14 m&l for dismantling the non clogging sewagepump ( 5.0 to 7.5 hp ) from foundation including electric and mechanical connection and taking out from 10 mtr deep sewage well with chain pulley block and instalation, reconnecting the electric and mechanical connection at existing location after carrying out minor repairs including replacement oil seal, oil, hanging chain etc all as specified and directed by engineer in charge. make :crompton greaves ltd, ksb ( note spare parts required for replacement shall be measured and paid separetalyrespective items. 15 transportation of motor to workshop and back to site after repair, cutting of burnt winding & rewinding the stator with super enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles ete as per relevent is standard / manufacturers recommendation as directed by eic. 16 supply only ball bearing nde and de as per existing numbers. make nde / de or equivalent as approved by ge. 17 all as per item no. 10 above but non clogging sewage pump ofcapacity 12.5 hp 18 transportation of motor to workshop and back to site after repair, cutting of burnt winding & rewinding the stator with super enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles ete as per relevent is standard / manufacturers recommendation as directed by eic. 19 supply only ball bearing nde and de as per existing numbers. 20 all as per item no. 10 above but non clogging sewage pump ofcapacity 3 / 4 hp 21 transportation of motor to workshop and back to site after repair, cutting of burnt winding & rewinding the stator with super enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles ete as per relevent is standard / manufacturers recommendation as directed by eic. 22 supply only ball bearing nde and de as per existing numbers. make nde / de or equivalent as approved by ge. 23 dismentling of centrifugal / monoblock pump set after disconnecting from power mains & pipe line of capacity 7.5 to 15 hp, 3 phase, 415 volts 50 hz, acof make kirloskar fromfoundation and dismantlingfor overhauling repairincludingreplacementof unservicablepart oiling , greasing, reinstalling and connecting with suction / dischargeline with correctalignment by replacing glandstuds and making completeelectricconnection includingtesting complete all as specifiedand directed. ( note spare parts required for replacement shall be measured and paid separetalyas supply only under respective item ) 24 transportation of motor to workshop and back to site after repair, cutting of burnt winding & rewinding the stator with super enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles ete as per relevent is standard / manufacturers recommendation as directed by eic. 25 supply only stainless steel pump shaft 26 supply only gun metal impeller with neck key, distance bush 27 supply only ball bearing as per existing number. 28 all as per item no. 13 above but centrifugal / monoblock pump ofcapacity 25 hp 29 transportation of motor to workshop and back to site after repair, cutting of burnt winding & rewinding the stator with super enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles ete as per relevent is standard / manufacturers recommendation as directed by eic. 30 supply only stainless steel pump shaft 31 supply only gun metal impeller with neck key, distance bush 32 supply only ball bearing as per existing number. 33 dismentling of filter press pump set, gear boxmotor after disconnecting from power mains & pipe line of capacity 1.5 hp to 2 hp , 3 phase, 415 volts 50 hz, acfromfoundation and dismantlingfor overhauling repairincludingreplacementof unservicablepart oiling , greasing, reinstalling and connecting with suction / dischargeline with correctalignment by replacing of gear road / pin and making completeelectricconnection includingtesting complete all as specifiedand directed. ( note spare parts required for replacement shall be measured and paid separetalyas supply only under respective items ) 34 transportation of motor to workshop and back to site after repair, cutting of burnt winding & rewinding the stator with super enamelled copper wire of suitable size and class of insulation including insulation paper, sleeves, thimbles ete as per relevent is standard / manufacturers recommendation as directed by eic. 35 supply only set of gear box as per existing model. 36 supply onlyneck key, distance bush 37 supply only ball bearing as per existing number. 38 supply only fan belt as per existing number. 39 m&l for taking out & servicing of existing air blower ( make everest, ) of capacity488 cum / hr from authorised service centre of everest company with taking out of electric cable complete and reconnecting the electric and mechanical connection at existing location after carrying out minor repairs including replacement of oil seal, oil, locking arrangement of pully, belt, gland packing etc all as specified and directed by engineer in charge. ( note spare parts required for replacement shall be measured and paid separetaly as supply only under respective items ) 40 supply only air filter suitable for above modelstainless steel pump shaft 41 supply only ball bearing ( make skf or equivalent as approved by ge ) 42 supply only set of rotor with hub as per existing model. 43 supply only set of gear with hub as per existing model. 44 taking out & rewinding the existing burnt blowermotor 20 hp, 3phase, 50 cycles by disconnecting electrically and mechanically and transporting to the locally contractors workshop. dismantlingthemotor and removing the old burnt copper winding & demoisturise, cleaning, rewindingthecoilswith same gauge super enamelled copper wire, with suitable f class paper insulation, varnishing, andreassembling by replacing bearings, remetalling of armature shaft and turning on lathe to give proper size for bearing fittings, replacement of terminal plate and reinstalling at the installation andtesting, commissioning etc complete.note before rewinding the existing motor, contractor must show the burnt motor / winding to the eic. old unserviceable copper retrieved will be property of contractor 45 supply & fix in repair pvc insulated, pvc sheathed, submersible flat cable isi marked with multi stranded copper conductor 1100 volt grade of size 6 sqmm 3 core of with pvc conduit of size 25mm dia for connecting pump from panel including heavy duty pvc conduit as per ground requirement complete all as specified and directed. 46 supply & fix in repair 3 pole power contactor type mnx 9 of ac3 9amp, 415v, 50 hz complete all as specified and directed. 47 supply & fix in repair contactor type mnx 32 of ac3 32amp, 415v, 50 hz complete all as specified and directed. 48 supply & fix in repair front mounting add on aux contact block mnx a2, 1no+1nc, 415v, 50 hz of make l&t, c&s, schneider or equivelent as approved by ge 49 supply & fix in repair control relay ( auxiliary contactors ) type mx0 22e ( 2no + 2nc ) , 415v of make l&t, abb, ae, or equivelent as approved by ge 50 supply & fix in repair mcb tp, c curve of capacity 6 amp to 32 amp 415v complete all as specified and directed. 51 supply & fix in repair mcb tpn, c curve of capacity 40 amp to 63 amp 415v complete all as specified and directed. 52 m & l for testing of treated water ( stp 1, 2, 3, 4&5 ) from regional govt approved test lab or nabl accredited lab. the undermentioned test should be carried out by each treated water sample and their characteristics will be as under: ( i ) biochemical oxygen demand ( bod ) < 10 mg / litre ( ii ) chemical oxygen demand ( cod ) < 150 mg / litre ( iii ) total suspended solids ( tss ) < 10 mg / litre ( iv ) dissolved oxygen ( do ) > 5 mg / litre ( v ) ph should be 6.5 to 8.5 ( vi ) residual chlorine > 0.5 mg / litre or more ( vii ) outlet coliform < 100 counts / 100ml note : ( i ) the frequency of all test should be once in a month at equal interval. ( ii ) ph and residual chlorine shall be tested on daily basis in the presence of je e / m / age e / m. ph meter and chlorine testing kit shall be provided by the contractor and cost of which shall be deemed to be included in the quoted rates. 53 m&l for rectification of leakage ( priming system ) from gi 15 / 20 mm size bore pipe line by cutting defective gi pipe by connecting with old line with and including necessary fittings such as socket & union, nipple, gate valveincluding screwingold & new pipe including all necessary earth work for connecting complete all as specified and directed. 54 s&f in repair of old u / sgland packing of valves / pump set of any sizes / capacity complete with neoprene rubber gasket , jointing material and nuts / bolts / washer of suitable size complete all as specified and directed. 55 s&f in repair ci foot valve isi marked with all fittings of size 100 mm dia 56 m & l for plaincement concrete 1:3:6 type c 1 ( 20mm graded aggregate ) in foundation filling mass concreting etc for making good the disturbed portion of road / floor / platform including form work etc complete all as specified and directed. 57 s&f in repairs electro magnetic diaphragm pump model v 12 having a capacity of 6.0 lph at maximum injection pressure of 3.5 kg / cm2 complete with pp head, fittings, footvalve, antisyphon valve and suitable to operate on 230 v / single phase / 50 hz ac supply including connecting to pipe line including testing complete as directed by eic. 58 servicing / overhauling ofsludge cake machinemake sachinfiltech pvt ltdafter disconnecting frompipe by authorised manufacturecompany, opening andchecking of various components andproper cleaning and greasing / oilingincd if any spare parts requiredfor repair and fuctioning of machine inclreplace compnay approved cloth as required each machine and pvc handle, knob, gear etcshall be deemed to be included in quoted rate of this item and testing of machine after repair complete and making sluge brick / rollall as directed by engr in charge. 59 labour only for checking the serviceability of different spares / component / parts of the starter and motor pump set / panel of any capacity at any site complete all as directed by engr in charge 60 supply and fix in repair of fullyautomatic star delta starter 10 hpcomprising of combo volt andammeter single phase preventor, over load relayand timer housed in ms sheet power coated enclosure of 10 hp capacity complete all as specified and directed. 61 supply and fix in repair ofstarter 5 hp comprising of combo volt andammeter, over load relayin ms sheet power coated enclosure complete all as specified and directed. 62 providing daily area cleaning / sweeping of preimises of following stp including cutting outgreen vegetation, roots, bushes, treebranches, picking polythene and other unwanted material from theinstallation area, spreading of suitable chemical to stop growing unwanted vegitation / grass and maintaining the ground surrounding the installation and removing the same out sidethe defence area as directed by engr in charge. the approx area of installation kept clean all as under.stp no 1 6000 sqm 63 all as per item no 35.01 here in before but stpno 02 4900 sqm 64 all as per item no 35.01 here in before but stp no 3 6100 sqm 65 all as per item no 35.01 here in before but raw sump hameed vihar 3000 sqm 66 all as per item no 35.01 here in before but stp no 4 8000sqm 67 all as per item no 35.01 here in before but stpno 05 12000 sqmnote : for item no 35.01 to 35.06 ( i ) if contractor fail is the clean the area of installation that recovery @ 5000 per job shall be recovered from his dues and contractors claim on this account shall not be entertained. ( ii ) contractor shall provide required t&p like as ( broom, axe, saw, bucket etc ) ( ii ) area will be maintained throughout the contract peroid from the date of commencement to date of completion and the payment will be made at once only. 68 m & l forci butterfly valve 100 mm dia, isi marked, complete with all fittings / accessories, required for fixing complete all as specified and directed 69 m&l for water high pressure gauge including socket welded to measure pressure in the deliverypipe 0 150 psi kg / cm2 make fe / big / guru, ramco or equivalent as approved by ge 70 earthing complete with glavanised steel earth plate elactrode 600mm x600mm x6.0 mm thick buried directly in ground ( earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to galvanised earth lead strip 25 x 4mm sizeby means of nut , bolt, check nut and washer ofgalvanised iron or of steel, earth lead protected by 40 mm dia gi pipe light grade watering pipe 20 mm dia gi light grade gi wire meshed funnel alternate layer of charcoal and salt pcc chamber , recessed for and including rcc cover including all necessary excavation and earth work, earth wire connected to main switch board, testing the earthing after completion all as specified and shown in electric plate no 3 of mes ssr pt i 2009 print, complete all as specified & directed ( pannel earthing ) . 71 taking out non clog sewage lifting pump set of cap5 to 12.5 hp, 3 phase, 415 volts, 50hz, ac supply along withpipe from the sewage collection well andremoveing mud, plastic, cloth, poleythen, stone etc completeand testing then lowering the same after cleaning complete all as specified and directed 72 taking out old unserviceable pvcbio filter media filling and m&l pvcbio filter mediafilling for mbbbr as per exisiting size all as directed by engr in charge. 73 material and labour for fabrication of retro reflectroised sign board of size exceeding 0.90 sqm as per irc : 67 made of encapsulated lens type reflective sheeting, fixed over aluminium sheet 1.5 mm thick of required size duly written with thematter as directed in blue colourmounted on angle iron / ms pipe support complete and including grouting the sign board in brick work, plastered and white wash on all exposed surfaces or in pcc 1:2:4 type b 2 using 40 mm graded stone aggregate complete all as directed by engineer in charge.note – ( i ) angle iron frame work, pcc, brick work, plastering and white wash shall be measured and paid for separately under appropriate item of schedule a ( ii ) retro reflective sheet and letters shall be astm 4956 type 3 of high intensity grade of make: 3m grade 3870 / kiwalite 22000 / avery dennison series 6200 or equivalent as approved by ge 74 material and labour for mild steel frame work confirming to fe 290 ( gde e 165 ) of sign boards made of m s angle iron or ms square or round pipe of suitable thickness and size as directed duly painted with two coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces complete all as directed and specified by engineer in charge.note : the surface of angle iron coming in contact with pcc / brick work shall be painted with two coats of bituminous paint and rate quoted for above item shall be deemed to inclusive of same. 75 s & f for rotational moulded polyethylene water cantainer500 litres capacity ( cylindrical vertical with lid ) , double layer, isi marked, fixed in position with pp head, fittings, footvalve, antisyphon valve, end block plateincluding connecting to pipe line assuitable length including testing complete as directed by eic. 76 all as per item no. 44 above but capacity 1000 litres. 77 providing / fabrecation in replacement of fire point stand made out of angle iron 40x40x5mm thickand canopy roof made out of mssheet 22 gauge thick incl provision for hanging 03 buckets fill with sandincluding 02 nos fire extingusher a / b / c type incl pcc foundation, pick axe, belcha complete sample drg approved by engr in charge before fabrication 78 supplying, laying, jointing and testingductile iron pressure pipe centrifugally castisi marked with socket and spigot ends including all necessary fittings with jointing materialsconforming to is 8329 / 2000 standard length , of k7 specification with out zinc coatinglaid in trenches, under floor, road etc of following dia sizes including taking out old unsv hdpe / pvc pipe : 150 mmmake jindal ltd / electrosteel casting ltd / tata or equivalent as approved by ge 79 all as per item no 47.01 here in before but 100 mm 80 m&l for rendering 10 mm thick cement plaster in cm 1:4 on stone masonary orfaces of brick work including finished even and smooth without using extra cement including taking down old complete all as directed. 81 excavation & earth work in trenches n.exc 1.5m wide and n.exc 1.5m in depth and getting out in soft and loose soil including trimming of sides and bottom of trenches complete all as specified and directed. 82 returning, filling in, including spreading, watering and well ramming in layers n.exc 25cm thick each in soft / loose soil complete all as specified and directed. 83 removing excavated surplus soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting pointcomplete all as specified and directed. 84 m & l for 3 layer pp r ( polypropylene random copolymer ) concealed pipes sdr 7.4 pn 16 uv stabilised and antimicrobial fusion welded having thermal stability for sewage treated water supply and including all types required fittings with pp r plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and directed of the following sizes : 75 mm dia note :wall thickness of pipe shall beas per is 1580 ( make zindal / sfmc / kanha plastic pvt ltd or equivalent as approved by ge ) 85 all as per item no 52 here in before but 50 mm dia 86 all as per item no 52 here in before but 25 mm dia 87 all as per item no 52 here in before but 15 mm dia 88 disconnecting exisitng lt over heated or burnt cable terminal / joint at panel / feeder pillar & lt cable of any size cutting out over heated / burnt / unserviciable portion of cable, stretching / opening cable to suitable required length etc and fixing aluminium lugs / joint material and suitablenuts bolts & washeretc all as direeted by engr in charge 89 supply and fix of flex board of water installation and machine specification board size 45cm x 60cm fix on fronteach and every equipment , machiney specification given by engr in charge 90 m&l foructech 01 ( liquid floculant ) using for the de established colloidal particales together to form large aggregates of sewage water, dozing 2.5 kg / 50 ppm per day ( for two times ) and using at the time of peak water flow in a settling tank complete all as specified and directed. make : urveeka chemteck pvt ltd, or euivalent makeas approvedby ge 91 m&l for uctech 02 ( liquid coagulant ) using for neutralizing the non settleable particles & allow to form clumps of sewage water, dozing2.5 kg / 50 ppm per day ( for two times ) and using at the time of peak water flow in a settling tank complete all as specified and directed.make : urveeka chemteck pvt ltd, or euivalent makeas approvedby ge 92 m&l for uctech 04 ( liquid disinfectant ) using for deal with bacterial problem and make fare color ofwater, dozing 4 kg / 80 ppm per day ( for two times ) and using at the time of peak water flow in a holdingtank complete all as specified and directed. make : urveeka chemteck pvt ltd, or euivalent makeas approvedby ge 93 m&l foructech 03 ( liquiddeodprizer ) using for stop biological fouling in working zone and make odorless water to provide healthy environment of sewage water , dozing 3 kg / 60 ppm per day ( for three times ) and using at the time of peak water flow in a collectiontank complete all as specified and directed.make : urveeka chemteck pvt ltd, or euivalent makeas approvedby ge 94 m&l for uctech 07 ( nutrient chemical ) using for maintain the ph in 7 8 range to sustain quality of water as per pollution control normof water , dozing 5 kg in a week ( for two times ) and using at the time of peak water flow in a aerationtank complete all as specified and directed. make : urveeka chemteck pvt ltd, or euivalent makeas approvedby ge 95 m& l preparing old steel surfaces and applying one coat of synthetic enamel paint as per existing colour such as ( pipe line, filter tank and pump etc ) including marking ofarrow sign and name in capital letter with black synthetic enamel paintthe following equpt each stp ( i ) treated pump 02 nos ( ii ) filter feed pump 02 nos ( iii ) air blower 02 nos ( iv ) press filter motor 02 nos ( v ) suction / discharge line ( vi ) filter 02 nos 96 s&f 1.25 meter length of gi 20mm dia size medium grade pipe as tapping point pipe by providing 20mm dia bore gate valve with excavation of earth& refilling complete for trenches of size 2.0 x 1.0 x 1.0 meter for existing pipe line dia by proper punching for water tapping& connected with suitable saddle / clamp of size 25 x 3 mm with nut bolts & accessories complete & in pcc ( 1:3:6 ) , type c1, using 20mm graded stone aggregate for stand post of size 200 x 200 x 300mm testing & commissioning on water pressure complete as directed by eic. 97 supply and fix in repair mccb tpn 63 amp to 100 amp , 415 volts, 50 hz 35ka complete all as specified and directed. 98 supply and fix in repair mccb tpn 200 amp , 415 volts, 50 hz 35ka complete all as specified and directed. 99 supply and fix in repair mccb tpn 250 amp , 415 volts, 50 hz 35ka complete all as specified and directed. 100 s&f in repair submersible copper cable pvc insulated over all sheethed flat isi marked of 1100 volts grade of 10 sqmm 3 core. ( make: finolex / l&t / havells ) 101 s&f in repair submersible copper cable pvc insulated over all sheethed flat isi marked of 1100 volts grade of 6 sqmm 3 core. ( make: finolex / l&t / havells ) 102 s&f in replacementair pressure pipe as per existing size approx 6mtr long for connection filter press pump machine incl connection fitting , clamp , nozel etc including testing complete as directed by eic. ...
50
Public Works Department - Rajasthan
35702730 colour, white wash, barricading work and repair work on republic day 2023 at ambedkar stadium tonk...